INTERNET-DRAFT Zhaohui Zhang, Ed.
Intended Status: Proposed Standard Juniper
Expires: 2016-02-12 Saud Asif
AT&T
Andy Green
BT
Sameer Gulrajani
Cisco
Pradeep Jain
Alcatel-Lucent
2015-08-12
MPLS/BGP Layer 3 VPN Multicast
Management Information Base
draft-ietf-bess-mvpn-mib-01
Abstract
This memo defines an portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it describes managed objects to configure and/or
monitor multicast in MPLS/BGP-based Layer-3 VPN (MVPN) on an MVPN
router.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as
Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/1id-abstracts.html
The list of Internet-Draft Shadow Directories can be accessed at
Zhaohui Zhang Expires 2016-02-12 [Page 1]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
http://www.ietf.org/shadow.html
Copyright and License Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Terminology . . . . . . . . . . . . . . . . . . . . . . . . 3
2 MVPN MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1 Summary of MIB Module . . . . . . . . . . . . . . . . . . . 3
2.2 MIB Module Definitions . . . . . . . . . . . . . . . . . . 5
3 Security Considerations . . . . . . . . . . . . . . . . . . . . 29
4 IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 29
5 Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . 29
6 References . . . . . . . . . . . . . . . . . . . . . . . . . . 29
6.1 Normative References . . . . . . . . . . . . . . . . . . . 30
6.2 Informative References . . . . . . . . . . . . . . . . . . 30
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 30
Zhaohui Zhang Expires 2016-02-12 [Page 2]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
1 Introduction
Multicast in MPLS/BGP L3 VPNs is specified in [MVPN], [BGP-MVPN] and
[MVPN-WILDCARD]. These specifications support either PIM or BGP as
the protocol for exchanging VPN multicast (referred to as C-multicast
states, where 'C-' stands for 'VPN Customer-') among PEs. In the rest
of this document we'll use the term "PIM-MVPN" to refer to PIM being
used for exchanging C-multicast states, and "BGP-MVPN" to refer to
BGP being used for exchanging C-multicast states.
This document defines a standard MIB for MVPN-specific objects that
are generic to both PIM-MVPN and BGP-MVPN.
This document borrowed some text from Cisco PIM-MVPN MIB [CISCO-MIB].
For PIM-MVPN this document attempts to provide coverage comparable
to [CISCO-MIB], but in a generic way that applies to both PIM-MVPN
and BGP-MVPN.
Comments should be made directly to the BESS WG at bess@ietf.org.
1.1 Terminology
This document adopts the definitions, acronyms and mechanisms
described in [MVPN] and other documents that [MVPN] refers to.
Familiarity with Multicast, MPLS, L3VPN, MVPN concepts and/or
mechanisms is assumed.
Interchangeably, the term MVRF and MVPN are used to refer to a
partiular Multicast VPN instantiation on a particular PE device.
2 MVPN MIB
This MIB enables configuring and/or monitoring of MVPNs on PE
devices: the whole multicast VPN machinery and the per-MVRFs
information, including the configuration, status and operational
details, such as different PMSIs and the provider tunnels
implementing them.
2.1 Summary of MIB Module
The configuration and states specific to an MVPN include the
following:
- C-multicast routing exchange protocol (PIM or BGP)
- I-PMSI, S-PMSI and corresponding provider tunnels
Zhaohui Zhang Expires 2016-02-12 [Page 3]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
- Mapping of c-multicast states to PMSI/tunnels
To represent them, the following tables are defined.
+--------------+
| MvpnBgp |
| General |
+--------------+ +-------------------+ +-----------------+
| MvpnGeneral | -> | MvpnPmsiConfig | <- | MvpnSpmsiConfig |
+--------------+ +-------------------+ +-----------------+
+--------------+ +-------------------+ +-----------------+
| MvpnIpmsi | -> | L2L3VpnMcastPmsi | <- | MvpnSpmsi |
+--------------+ | TunnelAttribute | +-----------------+
-> +-------------------+
/ ^
/ |
+--------------+ +-------------------+
| MvpnInterAs | | MvpnMroute |
| Ipmsi | +-------------------+
+--------------+
- mvpnGeneralTable/Entry
An entry in this table is created for every MVRF in the device, for
general configuration/states of the MVRF, including I-PMSI
configuration.
Existence of the corresponding VRF in [L3VPN-MIB] is necessary for
a row to exist in this table.
- mvpnBgpGeneralTable/Entry
This table augments mvpnGeneralTable and is for BGP-MVPN specific
information.
- mvpnSpmsiConfigTable/Entry
This table contains objects for S-PMSI configurations in an MVRF.
- mvpnPmsiConfigTable/Entry
Both I-PMSI configuration (in mvpnGeneralEntry) and S-PMSI
configuration (in mvpnSpmsiConfigEntry) refer to entries in this
Zhaohui Zhang Expires 2016-02-12 [Page 4]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
table.
- mvpnIpmsiTable/Entry
This table contains all advertised or received intra-as I-PMSIs.
With PIM-MVPN, it is applicable only when BGP-Based Autodiscovery
of MVPN Membership is used.
- mvpnInterAsIpmsiTable/Entry
This table contains all advertised or received inter-as I-PMSIs.
With PIM-MVPN, it is applicable only when BGP-Based Autodiscovery
of MVPN Membership is used.
- mvpnSpmsiTable/Etnry
This table contains all advertised or received S-PMSIs.
- l2l3VpnMcastPmsiTunnelAttributeTable/Entry
This table is defined separately in l2L3VpnMcastMIB [L2L3MVPN-MIB],
which is common for both VPLS Multicast and MVPN. It contains
sent/received PMSI attribute entries referred to by mvpnIpmsiEntry,
mvpnSpmsiEntry, mvpnInterAsIpmsiEntry, and other MIB objects (e.g.,
VPLS Multicast ones).
- mvpnMrouteTable/Entry
This table augments ipMcastMIB.ipMcast.ipMcastRouteTable [MROUTE-
MIB], for some MVPN specific information.
2.2 MIB Module Definitions
MCAST-VPN-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
experimental, Unsigned32
FROM SNMPv2-SMI
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
FROM SNMPv2-CONF
TruthValue, RowPointer, RowStatus, TimeStamp, TimeInterval
FROM SNMPv2-TC
SnmpAdminString
FROM SNMP-FRAMEWORK-MIB
Zhaohui Zhang Expires 2016-02-12 [Page 5]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
InetAddress, InetAddressType
FROM INET-ADDRESS-MIB
MplsLabel
FROM MPLS-TC-STD-MIB
mplsL3VpnVrfName, MplsL3VpnRouteDistinguisher
FROM MPLS-L3VPN-STD-MIB
ipMcastRouteEntry
FROM IPMCAST-MIB
L2L3VpnMcastProviderTunnelType
FROM L2L3-VPN-MCAST-MIB;
mvpnMIB MODULE-IDENTITY
LAST-UPDATED "201405071200Z" -- 07 May 2014 12:00:00 GMT
ORGANIZATION "IETF Layer-3 Virtual Private
Networks Working Group."
CONTACT-INFO
" Jeffrey (Zhaohui) Zhang
zzhang@juniper.net
Comments and discussion to bess@ietf.org"
DESCRIPTION
"This MIB contains managed object definitions for
multicast in BGP/MPLS IP VPNs defined by [MVPN].
Copyright (C) The Internet Society (2015)."
-- Revision history.
REVISION "201405071200Z" -- 07 May 2014 12:00:00 GMT
DESCRIPTION
"Initial version of the draft."
::= { experimental 99 } -- number to be assigned
-- Top level components of this MIB.
mvpnNotifications OBJECT IDENTIFIER ::= { mvpnMIB 0 }
-- tables, scalars
mvpnObjects OBJECT IDENTIFIER ::= { mvpnMIB 1 }
-- conformance information
mvpnConformance OBJECT IDENTIFIER ::= { mvpnMIB 2 }
-- mvpn Objects
mvpnScalars OBJECT IDENTIFIER ::= { mvpnObjects 1 }
Zhaohui Zhang Expires 2016-02-12 [Page 6]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnGeneral OBJECT IDENTIFIER ::= { mvpnObjects 2 }
mvpnConfig OBJECT IDENTIFIER ::= { mvpnObjects 3 }
mvpnStates OBJECT IDENTIFIER ::= { mvpnObjects 4 }
-- Scalar Objects
mvpnMvrfNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of MVRFs for IPv4 or IPv6 or mLDP
C-Multicast that are present in this device."
::= { mvpnScalars 1 }
mvpnMvrfNumberV4 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of MVRFs for IPv4 C-Multicast that are
present in this device."
::= { mvpnScalars 2 }
mvpnMvrfNumberV6 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of MVRFs for IPv6 C-Multicast that are
present in this device."
::= { mvpnScalars 3 }
mvpnMvrfNumberPimV4 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PIM-MVPN MVRFs for IPv4 C-Multicast that are
present in this device."
::= { mvpnScalars 4 }
mvpnMvrfNumberPimV6 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of PIM-MVPN MVRFs for IPv6 C-Multicast that are
Zhaohui Zhang Expires 2016-02-12 [Page 7]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
present in this device."
::= { mvpnScalars 5 }
mvpnMvrfNumberBgpV4 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BGP-MVPN MVRFs for IPv4 C-Multicast that are
present in this device."
::= { mvpnScalars 6 }
mvpnMvrfNumberBgpV6 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BGP-MVPN MVRFs for IPv6 C-Multicast that are
present in this device."
::= { mvpnScalars 7 }
mvpnMvrfNumberMldp OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of BGP-MVPN MVRFs for mLDP C-Multicast that are
present in this device."
::= { mvpnScalars 8 }
mvpnNotificationEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"If this object is TRUE, then the generation of all
notifications defined in this MIB is enabled."
DEFVAL { false }
::= { mvpnScalars 9 }
-- General MVRF Information Table
mvpnGeneralTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnGeneralEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the general information about the MVRFs
Zhaohui Zhang Expires 2016-02-12 [Page 8]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
present in this device."
::= { mvpnGeneral 1 }
mvpnGeneralEntry OBJECT-TYPE
SYNTAX MvpnGeneralEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created for every MVRF in the
device."
INDEX { mplsL3VpnVrfName,
mvpnGenAddressFamily }
::= { mvpnGeneralTable 1 }
MvpnGeneralEntry ::= SEQUENCE {
mvpnGenAddressFamily INTEGER,
mvpnGenOperStatusChange INTEGER,
mvpnGenOperChangeTime TimeStamp,
mvpnGenCmcastRouteProtocol INTEGER,
mvpnGenIpmsiConfig RowPointer,
mvpnGenInterAsPmsiConfig RowPointer,
mvpnGenUmhSelection INTEGER,
mvpnGenSiteType INTEGER,
mvpnGenSptnlLimit Unsigned32,
mvpnGenRowStatus RowStatus
}
mvpnGenAddressFamily OBJECT-TYPE
SYNTAX INTEGER { ipv4(1),
ipv6(2)
}
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Address Fammily that this entry is for"
::= { mvpnGeneralEntry 1 }
mvpnGenOperStatusChange OBJECT-TYPE
SYNTAX INTEGER { createdMvrf(1),
deletedMvrf(2),
modifiedMvrfIpmsiConfig(3),
modifiedMvrfSpmsiConfig(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object describes the last operational change that
happened for the given MVRF.
Zhaohui Zhang Expires 2016-02-12 [Page 9]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
createdMvrf - indicates that the MVRF was created in the
device.
deletedMvrf - indicates that the MVRF was deleted from the
device. A row in this table will never have
mvpnGenOperStatusChange equal to deletedMvrf(2),
because in that case the row itself will be deleted from the
table. This value for mvpnGenOperStatusChange is defined
mainly for use in mvpnMvrfChange notification.
modifiedMvrfIpmsiConfig - indicates that the I-PMSI
for the MVRF was configured, deleted or changed.
modifiedMvrfSpmsiConfig - indicates that the S-PMSI
for the MVRF was configured, deleted or changed."
DEFVAL { createdMvrf }
::= { mvpnGeneralEntry 2 }
mvpnGenOperChangeTime OBJECT-TYPE
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time at which the last operational change for the MVRF in
question took place. The last operational change is specified
by mvpnGenOperStatusChange."
::= { mvpnGeneralEntry 3 }
mvpnGenCmcastRouteProtocol OBJECT-TYPE
SYNTAX INTEGER { pim (1),
bgp (2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Protocol used to signal C-multicast states across the
provider core.
pim(1): PIM (PIM-MVPN).
bgp(2): BGP (BGP-MVPN)."
::= { mvpnGeneralEntry 4 }
mvpnGenIpmsiConfig OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This points to a row in mvpnPmsiConfigTable,
for I-PMSI configuration."
Zhaohui Zhang Expires 2016-02-12 [Page 10]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
::= { mvpnGeneralEntry 5 }
mvpnGenInterAsPmsiConfig OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This points to a row in mvpnPmsiConfigTable,
for inter-as I-PMSI configuration, in case of segmented
inter-as provider tunnels."
::= { mvpnGeneralEntry 6 }
mvpnGenUmhSelection OBJECT-TYPE
SYNTAX INTEGER {
highest-pe-address (1),
c-root-group-hashing (2),
ucast-umh-route (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The UMH selection method for this mvpn, as specified in
section 5.1.3 of [MVPN]:
highest-pe-address (1): PE with the highest address
c-root-group-hashing (2): hashing based on (c-root, c-group)
uncast-umh-route (3): per ucast route towards c-root"
::= { mvpnGeneralEntry 7}
mvpnGenSiteType OBJECT-TYPE
SYNTAX INTEGER {
sender-receiver (1),
receiver-only (2),
sender-only (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Whether this site is a receiver-only site or not.
sender-receiver (1): both sender and receiver site.
receiver-only (2): receiver-only site.
sender-only (3): sender-only site."
::= { mvpnGeneralEntry 8}
mvpnGenSptnlLimit OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-write
STATUS current
Zhaohui Zhang Expires 2016-02-12 [Page 11]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
DESCRIPTION
"The max number of selective provider tunnels this device
allows for this mvpn."
::= { mvpnGeneralEntry 9}
mvpnGenRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This is used to create or delete a row in this table."
::= { mvpnGeneralEntry 10 }
-- General BGP-MVPN table
mvpnBgpGeneralTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnBgpGeneralEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table augments the mvpnGeneralTable and is for BGP-MVPN
specific information."
::= { mvpnGeneral 2 }
mvpnBgpGeneralEntry OBJECT-TYPE
SYNTAX MvpnBgpGeneralEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mvpnBgpGeneralEntry matches and augments an
mvpnGeneralEntry for a BGP-MVPN instance, with BGP-MVPN
specific informatoin."
AUGMENTS { mvpnGeneralEntry }
::= { mvpnBgpGeneralTable 1 }
MvpnBgpGeneralEntry ::= SEQUENCE {
mvpnBgpGenMode INTEGER,
mvpnBgpGenVrfRtImport MplsL3VpnRouteDistinguisher,
mvpnBgpGenSrcAs Unsigned32
}
mvpnBgpGenMode OBJECT-TYPE
SYNTAX INTEGER {
rpt-spt (1),
spt-only (2)
}
MAX-ACCESS read-write
STATUS current
Zhaohui Zhang Expires 2016-02-12 [Page 12]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
DESCRIPTION
"For two different BGP-MVPN modes:
rpt-spt(1): inter-site shared tree mode
spt-only(2): inter-site source-only tree mode."
::= { mvpnBgpGeneralEntry 1}
mvpnBgpGenVrfRtImport OBJECT-TYPE
SYNTAX MplsL3VpnRouteDistinguisher
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The VRF Route Import Extended Community that this device
adds to unicast vpn routes that it advertises for this mvpn."
::= { mvpnBgpGeneralEntry 2}
mvpnBgpGenSrcAs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Source AS number in Source AS Extended Community that this
device adds to the unicast vpn routes that it advertises for
this mvpn."
::= { mvpnBgpGeneralEntry 3}
-- PMSI Configuration Table
mvpnPmsiConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnPmsiConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table specifies the configured PMSIs."
::= { mvpnConfig 1 }
mvpnPmsiConfigEntry OBJECT-TYPE
SYNTAX MvpnPmsiConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created for each PMSI configured
on this router. It can be referred to by either I-PMSI
configuration (in mvpnGeneralEntry) or S-PMSI configuration
(in mvpnSpmsiConfigEntry)"
INDEX { mvpnPmsiConfigTunnelType,
mvpnPmsiConfigTunnelAuxInfo,
mvpnPmsiConfigTunnelPimGroupAddressType,
mvpnPmsiConfigTunnelPimGroupAddress,
Zhaohui Zhang Expires 2016-02-12 [Page 13]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnPmsiConfigTunnelOrTemplateName }
::= { mvpnPmsiConfigTable 1 }
MvpnPmsiConfigEntry ::= SEQUENCE {
mvpnPmsiConfigTunnelType L2L3VpnMcastProviderTunnelType,
mvpnPmsiConfigTunnelAuxInfo Unsigned32,
mvpnPmsiConfigTunnelPimGroupAddressType InetAddressType,
mvpnPmsiConfigTunnelPimGroupAddress InetAddress,
mvpnPmsiConfigTunnelOrTemplateName SnmpAdminString,
mvpnPmsiConfigEncapsType INTEGER,
mvpnPmsiConfigRowStatus RowStatus
}
mvpnPmsiConfigTunnelType OBJECT-TYPE
SYNTAX L2L3VpnMcastProviderTunnelType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Type of tunnel used to instantiate the PMSI."
::= { mvpnPmsiConfigEntry 1 }
mvpnPmsiConfigTunnelAuxInfo OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Additional tunnel information depending on the type.
pim: In case of S-PMSI, number of groups starting at
mvpnPmsiConfigTunnelPimGroupAddress.
This allows a range of PIM provider tunnel
group addresses to be specified in S-PMSI case.
In I-PMSI case, it must be 1.
rsvp-p2mp: 1 for statically specified rsvp-p2mp tunnel
2 for dynamically created rsvp-p2mp tunnel
ingress-replication:
1 for using any existing p2p/mp2p lsp
2 for dynamically creating new p2p lsp"
::= { mvpnPmsiConfigEntry 2 }
mvpnPmsiConfigTunnelPimGroupAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"In case of PIM provider tunnel, the type of tunnel address."
::= { mvpnPmsiConfigEntry 3 }
mvpnPmsiConfigTunnelPimGroupAddress OBJECT-TYPE
Zhaohui Zhang Expires 2016-02-12 [Page 14]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"In case of PIM provider tunnel, the provider tunnel address."
::= { mvpnPmsiConfigEntry 4 }
mvpnPmsiConfigTunnelOrTemplateName OBJECT-TYPE
SYNTAX SnmpAdminString
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The tunnel name or template name used to create tunnels.
Depending on mvpnPmsiConfigTunnelType and
mvpnPmsiConfigTunnelAuxInfo:
dynamically created rsvp-p2mp tunnel: template name
statically specified rsvp-p2mp tunnel: tunnel name
ingress-replication using
dynamically created lsps: template name
other: null"
::= { mvpnPmsiConfigEntry 5 }
mvpnPmsiConfigEncapsType OBJECT-TYPE
SYNTAX INTEGER { greIp (1),
ipIp (2),
mpls (3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The encapsulation type to be used, in case of PIM tunnel or
ingress-replication."
::= { mvpnPmsiConfigEntry 6 }
mvpnPmsiConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Used to create/modify/delete a row in this table."
::= { mvpnPmsiConfigEntry 7 }
-- S-PMSI configuration table
mvpnSpmsiConfigTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnSpmsiConfigEntry
MAX-ACCESS not-accessible
Zhaohui Zhang Expires 2016-02-12 [Page 15]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
STATUS current
DESCRIPTION
"This table specifies S-PMSI configuration."
::= { mvpnConfig 2 }
mvpnSpmsiConfigEntry OBJECT-TYPE
SYNTAX MvpnSpmsiConfigEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry is created for each S-PMSI configuration."
INDEX { mplsL3VpnVrfName,
mvpnSpmsiConfigCmcastAddressType,
mvpnSpmsiConfigCmcastGroupAddress,
mvpnSpmsiConfigCmcastGroupPrefixLen,
mvpnSpmsiConfigCmcastSourceAddress,
mvpnSpmsiConfigCmcastSourcePrefixLen }
::= { mvpnSpmsiConfigTable 1 }
MvpnSpmsiConfigEntry ::= SEQUENCE {
mvpnSpmsiConfigCmcastAddressType InetAddressType,
mvpnSpmsiConfigCmcastGroupAddress InetAddress,
mvpnSpmsiConfigCmcastGroupPrefixLen Unsigned32,
mvpnSpmsiConfigCmcastSourceAddress InetAddress,
mvpnSpmsiConfigCmcastSourcePrefixLen Unsigned32,
mvpnSpmsiConfigThreshold Unsigned32,
mvpnSpmsiConfigPmsiPointer RowPointer,
mvpnSpmsiConfigRowStatus RowStatus
}
mvpnSpmsiConfigCmcastAddressType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Type of C-multicast address"
::= { mvpnSpmsiConfigEntry 1 }
mvpnSpmsiConfigCmcastGroupAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"C-multicast group address"
::= { mvpnSpmsiConfigEntry 2 }
mvpnSpmsiConfigCmcastGroupPrefixLen OBJECT-TYPE
SYNTAX Unsigned32
Zhaohui Zhang Expires 2016-02-12 [Page 16]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"C-multicast group address prefix length.
A group 0 (or ::0) with prefix length 32 (or 128)
indicates wildcard group, while a group 0 (or ::0)
with prefix length 0 indicates any group."
::= { mvpnSpmsiConfigEntry 3 }
mvpnSpmsiConfigCmcastSourceAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"C-multicast source address"
::= { mvpnSpmsiConfigEntry 4 }
mvpnSpmsiConfigCmcastSourcePrefixLen OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"C-multicast source address prefix length.
A source 0 (or ::0) with prefix length 32 (or 128)
indicates a wildcard source, while a source 0 (or ::0)
with prefix length 0 indicates any source."
::= { mvpnSpmsiConfigEntry 5 }
mvpnSpmsiConfigThreshold OBJECT-TYPE
SYNTAX Unsigned32 (0..4294967295)
UNITS "kilobits per second"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The bandwidth threshold value which when exceeded for a
multicast routing entry in the given MVRF, triggers usage
of S-PMSI."
::= { mvpnSpmsiConfigEntry 6 }
mvpnSpmsiConfigPmsiPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This points to a row in mvpnPmsiConfigTable,
to specify tunnel attributes."
::= { mvpnSpmsiConfigEntry 7 }
Zhaohui Zhang Expires 2016-02-12 [Page 17]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnSpmsiConfigRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Used to create/modify/delete a row in this table."
::= { mvpnSpmsiConfigEntry 8 }
-- Table of intra-as I-PMSIs advertised/received
mvpnIpmsiTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnIpmsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is for all advertised/received I-PMSI
advertisements."
::= { mvpnStates 1 }
mvpnIpmsiEntry OBJECT-TYPE
SYNTAX MvpnIpmsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table corresponds to an I-PMSI
advertisement that is advertised/received on this router.
This represents all the sender PEs in the MVPN,
with the provider tunnel they use to send traffic."
INDEX { mplsL3VpnVrfName,
mvpnIpmsiAfi,
mvpnIpmsiRD,
mvpnIpmsiOrigAddrType,
mvpnIpmsiOrigAddress }
::= { mvpnIpmsiTable 1 }
MvpnIpmsiEntry ::= SEQUENCE {
mvpnIpmsiAfi Unsigned32,
mvpnIpmsiRD MplsL3VpnRouteDistinguisher,
mvpnIpmsiOrigAddrType InetAddressType,
mvpnIpmsiOrigAddress InetAddress,
mvpnIpmsiUpTime TimeInterval,
mvpnIpmsiAttribute RowPointer
}
mvpnIpmsiAfi OBJECT-TYPE
SYNTAX Unsigned32 (1|2)
MAX-ACCESS not-accessible
STATUS current
Zhaohui Zhang Expires 2016-02-12 [Page 18]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
DESCRIPTION
"The address family this I-PMSI is for.
1 - IPv4
2 - IPv6"
::= { mvpnIpmsiEntry 1 }
mvpnIpmsiRD OBJECT-TYPE
SYNTAX MplsL3VpnRouteDistinguisher
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Route Distinguisher in this I-PMSI."
::= { mvpnIpmsiEntry 2 }
mvpnIpmsiOrigAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Internet address type of mvpnIpmsiOrigAddress."
::= { mvpnIpmsiEntry 3 }
mvpnIpmsiOrigAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The BGP address of the device that originated the I-PMSI."
::= { mvpnIpmsiEntry 4 }
mvpnIpmsiUpTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this I-PMSI
was first advertised/received by the device."
::= { mvpnIpmsiEntry 5 }
mvpnIpmsiAttribute OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable."
::= { mvpnIpmsiEntry 6 }
-- Table of inter-as I-PMSIs advertised/received
Zhaohui Zhang Expires 2016-02-12 [Page 19]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnInterAsIpmsiTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnInterAsIpmsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table is for all advertised/received inter-as I-PMSI
advertisements."
::= { mvpnStates 2 }
mvpnInterAsIpmsiEntry OBJECT-TYPE
SYNTAX MvpnInterAsIpmsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table corresponds to an inter-as I-PMSI
advertisement that is advertised/received on this router.
This represents all the ASes in the MVPN,
with the provider tunnel used to send traffic to."
INDEX { mplsL3VpnVrfName,
mvpnInterAsIpmsiAfi,
mvpnInterAsIpmsiRD,
mvpnInterAsIpmsiSrcAs }
::= { mvpnInterAsIpmsiTable 1 }
MvpnInterAsIpmsiEntry ::= SEQUENCE {
mvpnInterAsIpmsiAfi Unsigned32,
mvpnInterAsIpmsiRD MplsL3VpnRouteDistinguisher,
mvpnInterAsIpmsiSrcAs Unsigned32,
mvpnInterAsIpmsiAttribute RowPointer
}
mvpnInterAsIpmsiAfi OBJECT-TYPE
SYNTAX Unsigned32 (1|2)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address family this I-PMSI is for.
1 - IPv4
2 - IPv6"
::= { mvpnInterAsIpmsiEntry 1 }
mvpnInterAsIpmsiRD OBJECT-TYPE
SYNTAX MplsL3VpnRouteDistinguisher
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Route Distinguisher in this inter-as I-PMSI."
::= { mvpnInterAsIpmsiEntry 2 }
Zhaohui Zhang Expires 2016-02-12 [Page 20]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnInterAsIpmsiSrcAs OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The source-as in this inter-as I-PMSI."
::= { mvpnInterAsIpmsiEntry 3 }
mvpnInterAsIpmsiAttribute OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Points to a row in the l2L3VpnMcastPmsiTunnelAttributeTable."
::= { mvpnInterAsIpmsiEntry 4 }
-- Table of S-PMSIs advertised/received
mvpnSpmsiTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnSpmsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table has information about the S-PMSIs sent/received
by a device."
::= { mvpnStates 3 }
mvpnSpmsiEntry OBJECT-TYPE
SYNTAX MvpnSpmsiEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in this table is created or updated for every S-PMSI
advertised/received in a particular MVRF."
INDEX { mplsL3VpnVrfName,
mvpnSpmsiCmcastAddrType,
mvpnSpmsiCmcastGroup,
mvpnSpmsiCmcastGroupPrefixLen,
mvpnSpmsiCmcastSource,
mvpnSpmsiCmcastSourcePrefixLen,
mvpnSpmsiOrigAddrType,
mvpnSpmsiOrigAddress}
::= { mvpnSpmsiTable 1 }
MvpnSpmsiEntry ::= SEQUENCE {
mvpnSpmsiCmcastAddrType InetAddressType,
mvpnSpmsiCmcastGroup InetAddress,
mvpnSpmsiCmcastGroupPrefixLen Unsigned32,
Zhaohui Zhang Expires 2016-02-12 [Page 21]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnSpmsiCmcastSource InetAddress,
mvpnSpmsiCmcastSourcePrefixLen Unsigned32,
mvpnSpmsiOrigAddrType InetAddressType,
mvpnSpmsiOrigAddress InetAddress,
mvpnSpmsiTunnelAttribute RowPointer,
mvpnSpmsiUpTime TimeInterval,
mvpnSpmsiExpTime TimeInterval,
mvpnSpmsiRefCnt Unsigned32
}
mvpnSpmsiCmcastAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Internet address type of mvpnSpmsiCmcastGroup/Source."
::= { mvpnSpmsiEntry 1 }
mvpnSpmsiCmcastGroup OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"S-PMSI C-multicast group address.
If it is 0 (or ::0), this is a wildcard group,
and mvpnSpmsiCmcastGroupPrefixLen must be 32 (or 128)."
::= { mvpnSpmsiEntry 2 }
mvpnSpmsiCmcastGroupPrefixLen OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"S-PMSI C-multicast group address prefix length."
::= { mvpnSpmsiEntry 3 }
mvpnSpmsiCmcastSource OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"S-PMSI C-multicast source address
If it is 0 (or ::0), this is a wildcard source,
and mvpnSpmsiCmcastSourcePrefixLen must be 32 (or 128)."
::= { mvpnSpmsiEntry 4 }
mvpnSpmsiCmcastSourcePrefixLen OBJECT-TYPE
SYNTAX Unsigned32
Zhaohui Zhang Expires 2016-02-12 [Page 22]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"S-PMSI C-multicast source address prefix length."
::= { mvpnSpmsiEntry 5 }
mvpnSpmsiOrigAddrType OBJECT-TYPE
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The Internet address type of mvpnSpmsiOrigAddress."
::= { mvpnSpmsiEntry 6 }
mvpnSpmsiOrigAddress OBJECT-TYPE
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The BGP address of the device that originated the S-PMSI."
::= { mvpnSpmsiEntry 7 }
mvpnSpmsiTunnelAttribute OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"A row pointer to the l2L3VpnMcastPmsiTunnelAttributeTable"
::= { mvpnSpmsiEntry 8 }
mvpnSpmsiUpTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time since this S-PMSI
was first advertised/received by the device."
::= { mvpnSpmsiEntry 9 }
mvpnSpmsiExpTime OBJECT-TYPE
SYNTAX TimeInterval
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"For UDP-based S-PMSI signaling for PIM-MVPN,
the amount of time remaining before this
received S-PMSI Join Message expires,
or the next S-PMSI Join Message refresh is to be
Zhaohui Zhang Expires 2016-02-12 [Page 23]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
advertised again from the device.
Otherwise, it is 0."
::= { mvpnSpmsiEntry 10 }
mvpnSpmsiRefCnt OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of c-multicast routes that are mapped to
this S-PMSI."
::= { mvpnSpmsiEntry 11 }
-- Table of multicast routes in an MVPN
mvpnMrouteTable OBJECT-TYPE
SYNTAX SEQUENCE OF MvpnMrouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table augments ipMcastRouteTable, to provide some MVPN
specific information."
::= { mvpnStates 4 }
mvpnMrouteEntry OBJECT-TYPE
SYNTAX MvpnMrouteEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The mvpnMrouteEntry matches and augments an ipMcastRouteEntry,
with MVPN specific information, such as PMSI used."
AUGMENTS { ipMcastRouteEntry }
::= { mvpnMrouteTable 1 }
MvpnMrouteEntry ::= SEQUENCE {
mvpnMroutePmsiPointer RowPointer,
mvpnMrouteNumberOfLocalReplication Unsigned32,
mvpnMrouteNumberOfRemoteReplication Unsigned32
}
mvpnMroutePmsiPointer OBJECT-TYPE
SYNTAX RowPointer
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The I-PMSI or S-PMSI this C-multicast route is using.
This is important because an implementation may not have an
interface corresponding to a provider tunnel,
Zhaohui Zhang Expires 2016-02-12 [Page 24]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
that can be used in ipMcastRouteNextHopEntry."
::= { mvpnMrouteEntry 1 }
mvpnMrouteNumberOfLocalReplication OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of replications for local receivers.
For example, if an ingress PE needs to send traffic out of
N PE-CE interfaces, then mvpnMrouteNumberOfLocalReplication
is N."
::= { mvpnMrouteEntry 2 }
mvpnMrouteNumberOfRemoteReplication OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of local replications for remote PEs. For example,
if the number of remote PEs that need to receive traffic is N,
then mvpnMrouteNumberOfRemoteReplication is N in case of
Ingress Replication, but may be less than N in case of RSVP-TE
or mLDP P2MP tunnels, depending on the actual number of
replications the PE needs do."
::= { mvpnMrouteEntry 3 }
-- MVPN Notifications
mvpnMvrfChange NOTIFICATION-TYPE
OBJECTS {
mvpnGenOperStatusChange
}
STATUS current
DESCRIPTION
"A mvpnMvrfChange notification signifies a change about
a MVRF in the device. The change event can be creation of
the MVRF, deletion of the MVRF or an update on the I-PMSI
or S-PMSI configuration of the MVRF. The change event
is indicated by mvpnGenOperStatusChange embedded in
the notification. The user can then query
mvpnGeneralTable, and/or mvpnSpmsiConfigTable to
get the details of the change as necessary.
Note: Since the creation of a MVRF is often followed by
configuration of I-PMSI and/or S-PMSIs for the MVRF,
more than one (three at most) notifications for a MVRF may
be generated serially, and it is really not necessary to
Zhaohui Zhang Expires 2016-02-12 [Page 25]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
generate all three of them. An agent may choose to generate a
notification for the last event only, that is for S-PMSI
configuration.
Similarly, deletion of I-PMSI and S-PMSI configuration on a
MVRF happens before a MVRF is deleted and it is recommended
that the agent send the notification for MVRF deletion
event only."
::= { mvpnNotifications 2 }
-- MVPN MIB Conformance Information
mvpnGroups OBJECT IDENTIFIER ::= { mvpnConformance 1 }
mvpnCompliances OBJECT IDENTIFIER ::= { mvpnConformance 2 }
-- Compliance Statements
mvpnCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement "
MODULE -- this module
MANDATORY-GROUPS {
mvpnScalarGroup,
mvpnGeneralGroup,
mvpnSpmsiConfigGroup,
mvpnSpmsiGroup,
mvpnMrouteGroup
}
GROUP mvpnIpmsiGroup
DESCRIPTION
"This group is mandatory for systems that support
BGP signaling for I-PMSI."
GROUP mvpnInterAsIpmsiGroup
DESCRIPTION
"This group is mandatory for systems that support
Inter-AS Segmented I-PMSI."
GROUP mvpnBgpGeneralGroup
DESCRIPTION
"This group is mandatory for systems that support
BGP-MVPN."
::= { mvpnCompliances 1 }
Zhaohui Zhang Expires 2016-02-12 [Page 26]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
-- units of conformance
mvpnScalarGroup OBJECT-GROUP
OBJECTS {
mvpnMvrfNumber,
mvpnMvrfNumberV4,
mvpnMvrfNumberV6,
mvpnMvrfNumberPimV4,
mvpnMvrfNumberPimV6,
mvpnMvrfNumberBgpV4,
mvpnMvrfNumberBgpV6,
mvpnMvrfNumberMldp,
mvpnNotificationEnable
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
global MVPN parameters."
::= { mvpnGroups 1 }
mvpnGeneralGroup OBJECT-GROUP
OBJECTS {
mvpnGenOperStatusChange,
mvpnGenOperChangeTime,
mvpnGenCmcastRouteProtocol,
mvpnGenIpmsiConfig,
mvpnGenInterAsPmsiConfig,
mvpnGenUmhSelection,
mvpnGenSiteType,
mvpnGenSptnlLimit,
mvpnGenRowStatus
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
per-VRF MVPN parameters."
::= { mvpnGroups 2 }
mvpnPmsiConfigGroup OBJECT-GROUP
OBJECTS {
mvpnPmsiConfigEncapsType,
mvpnPmsiConfigRowStatus
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
PMSI tunnel configurations."
::= { mvpnGroups 3 }
Zhaohui Zhang Expires 2016-02-12 [Page 27]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnSpmsiConfigGroup OBJECT-GROUP
OBJECTS {
mvpnSpmsiConfigThreshold,
mvpnSpmsiConfigPmsiPointer,
mvpnSpmsiConfigRowStatus
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
S-PMSI configurations."
::= { mvpnGroups 4 }
mvpnIpmsiGroup OBJECT-GROUP
OBJECTS {
mvpnIpmsiUpTime,
mvpnIpmsiAttribute
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
Intra-AS I-PMSI attributes."
::= { mvpnGroups 5 }
mvpnInterAsIpmsiGroup OBJECT-GROUP
OBJECTS {
mvpnInterAsIpmsiAttribute
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
Inter-AS I-PMSI attributes."
::= { mvpnGroups 6 }
mvpnSpmsiGroup OBJECT-GROUP
OBJECTS {
mvpnSpmsiTunnelAttribute,
mvpnSpmsiUpTime,
mvpnSpmsiExpTime,
mvpnSpmsiRefCnt
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
S-PMSI attributes."
::= { mvpnGroups 7 }
mvpnMrouteGroup OBJECT-GROUP
OBJECTS {
Zhaohui Zhang Expires 2016-02-12 [Page 28]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
mvpnMrouteNumberOfLocalReplication,
mvpnMrouteNumberOfRemoteReplication
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage
VPN multicast forwarding states."
::= { mvpnGroups 8 }
mvpnBgpGeneralGroup OBJECT-GROUP
OBJECTS {
mvpnBgpGenMode,
mvpnBgpGenVrfRtImport,
mvpnBgpGenSrcAs
}
STATUS current
DESCRIPTION
"These objects are used to monitor/manage BGP-MVPN "
::= { mvpnGroups 9 }
mvpnOptionalGroup OBJECT-GROUP
OBJECTS {
mvpnMroutePmsiPointer
}
STATUS current
DESCRIPTION
"Support of these object is not required."
::= { mvpnGroups 10}
END
3 Security Considerations
This document does not introduce new security risks.
4 IANA Considerations
This document does not require IANA assignments.
5 Acknowledgement
Some of the text has been taken almost verbatim from [CISCO-MIB].
We would like to thank Yakov Rekhter, Jeffrey Haas, Huajin Jeng, Durga
Prasad Velamuri for their helpful comments.
6 References
Zhaohui Zhang Expires 2016-02-12 [Page 29]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
6.1 Normative References
[L3VPN-MIB] Nadeau, T., Ed., and H. van der Linde, Ed., "MPLS/BGP
Layer 3 Virtual Private Network (VPN) Management
Information Base", RFC 4382, February 2006.
[MROUTE-MIB] McWalter, D., Thaler, D., and A. Kessler, "IP Multicast
MIB", RFC 5132, December 2007.
[MVPN] Eric C. Rosen, Rahul Aggarwal, et. al., Multicast in MPLS/BGP
IP VPNs, RFC 6513, February 2012.
[BGP-MVPN] R. Aggarwal, E. Rosen, T. Morin, Y. Rekhter, BGP Encodings
and Procedures for Multicast in MPLS/BGP IP VPNs,
RFC 6514, February 2012.
[MVPN-WILDCARD] E. Rosen, Y. Rekhter, Wildcards in Multicast VPN
Auto-Discovery Routes, RFC 6625, May 2012.
[L2L3MVPN-MIB] Zhang, J., L2L3 VPN Multicast MIB, draft-ietf-bess-
l2l3-vpn-mcast-mib, Work In Progress.
6.2 Informative References
[CISCO-MIB] Susheela Vaidya, Thomas D. Nadeau, Harmen Van der Linde,
Multicast in BGP/MPLS IP VPNs Management Information Base,
draft-svaidya-mcast-vpn-mib-02.txt, Work In Progress,
April 2005.
Authors' Addresses
Zhaohui Zhang (Editor)
Juniper Networks, Inc.
10 Technology Park Drive
Westford, MA 01886
USA
Email: zzhang@juniper.net
Saud Asif
AT&T
C5-3D30
200 South Laurel Avenue
Middletown, NJ 07748
USA
Email: sasif@att.com
Andy Green
BT Design 21CN Converged Core IP & Data
Zhaohui Zhang Expires 2016-02-12 [Page 30]
INTERNET DRAFT L3VPN Multicast MIB 2015-08-12
01473 629360
Adastral Park, Martlesham Heath, Ipswich IP5 3RE
UK
Email: andy.da.green@bt.com
Sameer Gulrajani
Cisco Systems
Tasman Drive
San Jose, CA 95134
USA
EMail: sameerg@cisco.com
Pradeep G. Jain
Alcatel-Lucent Inc
701 E Middlefield road
Mountain view, CA 94043
USA
Email: pradeep.jain@alcatel-lucent.com
Zhaohui Zhang Expires 2016-02-12 [Page 31]