Autonomic Networking: Definitions and Design Goals
RFC 7575
Internet Research Task Force (IRTF) M. Behringer
Request for Comments: 7575 M. Pritikin
Category: Informational S. Bjarnason
ISSN: 2070-1721 A. Clemm
Cisco Systems
B. Carpenter
Univ. of Auckland
S. Jiang
Huawei Technologies Co., Ltd
L. Ciavaglia
Alcatel Lucent
June 2015
Autonomic Networking: Definitions and Design Goals
Abstract
Autonomic systems were first described in 2001. The fundamental goal
is self-management, including self-configuration, self-optimization,
self-healing, and self-protection. This is achieved by an autonomic
function having minimal dependencies on human administrators or
centralized management systems. It usually implies distribution
across network elements.
This document defines common language and outlines design goals (and
what are not design goals) for autonomic functions. A high-level
reference model illustrates how functional elements in an Autonomic
Network interact. This document is a product of the IRTF's Network
Management Research Group.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Research Task Force
(IRTF). The IRTF publishes the results of Internet-related research
and development activities. These results might not be suitable for
deployment. This RFC represents the consensus of the Network
Management Research Group of the Internet Research Task Force (IRTF).
Documents approved for publication by the IRSG are not a candidate
for any level of Internet Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc7575.
Behringer, et al. Informational [Page 1]
RFC 7575 Autonomic Networking June 2015
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document.
Table of Contents
1. Introduction to Autonomic Networking . . . . . . . . . . . . 3
2. Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. Design Goals . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1. Self-Management . . . . . . . . . . . . . . . . . . . . . 5
3.2. Coexistence with Traditional Management . . . . . . . . . 6
3.3. Secure by Default . . . . . . . . . . . . . . . . . . . . 7
3.4. Decentralization and Distribution . . . . . . . . . . . . 8
3.5. Simplification of Autonomic Node Northbound Interfaces . 8
3.6. Abstraction . . . . . . . . . . . . . . . . . . . . . . . 8
3.7. Autonomic Reporting . . . . . . . . . . . . . . . . . . . 9
3.8. Common Autonomic Networking Infrastructure . . . . . . . 9
3.9. Independence of Function and Layer . . . . . . . . . . . 10
3.10. Full Life-Cycle Support . . . . . . . . . . . . . . . . . 10
4. Not among the Design Goals . . . . . . . . . . . . . . . . . 11
4.1. Eliminate Human Operators . . . . . . . . . . . . . . . . 11
4.2. Eliminate Emergency Fixes . . . . . . . . . . . . . . . . 11
4.3. Eliminate Central Control . . . . . . . . . . . . . . . . 11
5. An Autonomic Reference Model . . . . . . . . . . . . . . . . 12
6. Security Considerations . . . . . . . . . . . . . . . . . . . 13
7. Informative References . . . . . . . . . . . . . . . . . . . 13
Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . 15
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 15
Behringer, et al. Informational [Page 2]
RFC 7575 Autonomic Networking June 2015
1. Introduction to Autonomic Networking
Autonomic systems were first described in a manifesto by IBM in 2001
[Kephart]. The fundamental concept involves eliminating external
systems from a system's control loops and closing of control loops
within the autonomic system itself, with the goal of providing the
system with self-management capabilities, including self-
configuration, self-optimization, self-healing, and self-protection.
IP networking was initially designed with similar properties in mind.
An IP network should be distributed and redundant to withstand
outages in any part of the network. Routing protocols such as OSPF
and IS-IS exhibit properties of self-management and can thus be
considered autonomic in the definition of this document.
However, as IP networking evolved, the ever-increasing intelligence
of network elements was often not put into protocols to follow this
paradigm, but was put into external configuration systems. This
configuration made network elements dependent on some process that
manages them, either a human or a network management system.
Autonomic functions can be defined in two ways:
o On a node level: Nodes interact with each other to form feedback
loops.
o On a system level: Feedback loops include central elements as
well.
System-level autonomy is implicitly or explicitly the subject in many
IETF working groups, where interactions with controllers or network
management systems are discussed.
This work specifically focuses on node-level autonomic functions. It
focuses on intelligence of algorithms at the node level, to minimize
dependency on human administrators and central management systems.
Some network deployments benefit from a fully autonomic approach, for
example, networks with a large number of relatively simple devices.
Most currently deployed networks, however, will require a mixed
approach, where some functions are autonomic and others are centrally
managed. Central management of networking functions clearly has
advantages and will be chosen for many networking functions. This
document does not discuss which functions should be centralized or
follow an autonomic approach. Instead, it should help make the
decision which is the best approach for a given situation.
Behringer, et al. Informational [Page 3]
RFC 7575 Autonomic Networking June 2015
Autonomic function cannot always discover all required information;
for example, policy-related information requires human input, because
policy is by its nature derived and specified by humans. Where input
from some central intelligence is required, it is provided in a
highly abstract, network-wide form.
Autonomic Computing in general and Autonomic Networking in particular
have been the subject of academic study for many years. There is
much literature, including several useful overview papers (e.g.,
[Samaan], [Movahedi], and [Dobson]). In the present document, we
focus on concepts and definitions that seem sufficiently mature to
become the basis for interoperable specifications in the near future.
In particular, such specifications will need to coexist with
traditional methods of network configuration and management, rather
than realizing an exclusively autonomic system with all the
properties that it would require.
There is an important difference between "automatic" and "autonomic".
"Automatic" refers to a predefined process, such as a script.
"Autonomic" is used in the context of self-management. It includes
feedback loops between elements as well as northbound to central
elements. See also the definitions in the next section. Generally,
an automatic process works in a given environment but has to be
adapted if the environment changes. An autonomic process can adapt
to changing environments.
This document provides the definitions and design goals for Autonomic
Networking in the IETF and IRTF. It represents the consensus of the
IRTF's Network Management Research Group (NMRG).
2. Definitions
We make the following definitions.
Autonomic: Self-managing (self-configuring, self-protecting, self-
healing, self-optimizing); however, allowing high-level guidance by a
central entity, through Intent (see below). An autonomic function
adapts on its own to a changing environment.
Automatic: A process that occurs without human intervention, with
step-by-step execution of rules. However, it relies on humans
defining the sequence of rules, so is not Autonomic in the full
sense. For example, a start-up script is automatic but not
autonomic. An automatic function may need manual adjustments if the
environment changes.
Behringer, et al. Informational [Page 4]
RFC 7575 Autonomic Networking June 2015
Intent: An abstract, high-level policy used to operate the network.
Its scope is an autonomic domain, such as an enterprise network. It
does not contain configuration or information for a specific node
(see Section 3.2 on how Intent coexists with alternative management
paradigms). It may contain information pertaining to a node with a
specific role (for example, an edge switch) or a node running a
specific function. Intent is typically defined and provided by a
central entity.
Autonomic Domain: A collection of autonomic nodes that instantiate
the same Intent.
Autonomic Function: A feature or function that requires no
configuration and can derive all required information through self-
knowledge, discovery, or Intent.
Autonomic Service Agent: An agent implemented on an autonomic node
that implements an autonomic function, either in part (in the case of
a distributed function) or whole.
Autonomic Node: A node that employs exclusively autonomic functions.
It requires (!) no configuration. (Note that configuration can be
used to override an autonomic function. See Section 3.2 for more
details.) An Autonomic Node may operate on any layer of the
networking stack. Examples are routers, switches, personal
computers, call managers, etc.
Autonomic Network: A network containing exclusively autonomic nodes.
It may contain one or several autonomic domains.
3. Design Goals
This section explains the high-level goals of Autonomic Networking,
independent of any specific solutions.
3.1. Self-Management
The original design goals of autonomic systems as described in
[Kephart] also apply to Autonomic Networks. The overarching goal is
self-management, which is comprised of several "self" properties.
The most commonly cited are:
o Self-configuration: Functions do not require configuration, by
either an administrator or a management system. They configure
themselves, based on self-knowledge, discovery, and Intent.
Discovery is the default way for an autonomic function to receive
the information it needs to operate.
Behringer, et al. Informational [Page 5]
RFC 7575 Autonomic Networking June 2015
o Self-healing: Autonomic functions adapt on their own to changes in
the environment and heal problems automatically.
o Self-optimizing: Autonomic functions automatically determine ways
to optimize their behavior against a set of well-defined goals.
o Self-protection: Autonomic functions automatically secure
themselves against potential attacks.
Almost any network can be described as "self-managing", as long as
the definition of "self" is large enough. For example, a well-
defined Software-Defined Networking (SDN) system, including the
controller elements, can be described overall as "autonomic", if the
controller provides an interface to the administrator that has the
same properties as mentioned above (high level, network-wide, etc.).
For the work in the IETF and IRTF, we define the "self" properties on
the node level. It is the design goal to make functions on network
nodes self-managing, in other words, minimally dependent on
management systems or controllers, as well as human operators. Self-
managing functions on a node might need to exchange information with
other nodes in order to achieve this design goal.
As mentioned in the introduction, closed-loop control is an important
aspect of self-managing systems. This implies peer-to-peer dialogues
between the parties that make up the closed loop. Such dialogues
require two-way "discussion" or "negotiation" between each pair or
groups of peers involved in the loop, so they cannot readily use
typical top-down command-response protocols. Also, a discovery phase
is unavoidable before such closed-loop control can take place.
Multiparty protocols are also possible but can be significantly more
complex.
3.2. Coexistence with Traditional Management
For the foreseeable future, autonomic nodes and networks will be the
exception; autonomic behavior will initially be defined function by
function. Therefore, coexistence with other network management
paradigms has to be considered. Examples are management by command
line, SNMP, SDN (with related APIs), the Network Configuration
Protocol (NETCONF), etc.
Conflict resolution between a) autonomic default behavior and Intent
and b) other methods is therefore required. This is achieved through
prioritization. Generally, autonomic mechanisms define a network-
wide behavior, whereas the alternative methods are typically on a
node-by-node basis. Node-based management concepts take a higher
priority over autonomic methods. This is in line with current
Behringer, et al. Informational [Page 6]
RFC 7575 Autonomic Networking June 2015
examples of autonomic functions; for example, with routing, a
(statically configured) route has priority over the routing
algorithm. In short:
o lowest priority: autonomic default behavior
o medium priority: autonomic Intent
o highest priority: node-specific network management concepts, such
as command line, SNMP, SDN, NETCONF, etc. How these concepts are
prioritized is outside the scope of this document.
The above prioritization essentially results in the actions of the
human administrator always being able to overrule autonomic behavior.
This is generally the expectation of network operators today and
therefore remains a design principle here. In critical systems, such
as atomic power plants, sometimes the opposite philosophy is used:
The expectation is that a well-defined algorithm is more reliable
than a human operator, especially in rare exception cases.
Networking generally does not follow this philosophy yet. However,
warnings should be issued if node-specific overrides may conflict
with autonomic behavior.
In other fields, autonomic mechanisms disengage automatically if
certain conditions occur: The autopilot in a plane switches off if
the plane is outside a predefined envelope of flight parameters. The
assumption is that the algorithms only work correctly if the input
values are in expected ranges. However, some opinions suggest that
exactly in exceptional conditions is the worst moment to switch off
autonomic behavior, since the pilots have no full understanding of
the situation at this point and may be under high levels of stress.
For this reason, we suggest here to NOT generally disable autonomic
functions if they encounter unexpected conditions, because it is
expected that this adds another level of unpredictability in
networks, when the situation may already be hard to understand.
3.3. Secure by Default
All autonomic interactions should be secure by default. This
requires that any member of an autonomic domain can assert its
membership using a domain identity, for example, a certificate issued
by a domain certification authority. This domain identity is used
for nodes to learn about their neighboring nodes, to determine the
boundaries of the domain, and to cryptographically secure
interactions within the domain. Nodes from different domains can
also mutually verify their identity and secure interactions as long
as they have a mutually respected trust anchor.
Behringer, et al. Informational [Page 7]
RFC 7575 Autonomic Networking June 2015
A strong, cryptographically verifiable domain identity is a
fundamental cornerstone in Autonomic Networking. It can be leveraged
to secure all communications and thus allows automatic security
without traditional configuration, for example, preshared keys. See
also the document "Making The Internet Secure By Default" [Behringer]
for more information.
Autonomic functions must be able to adapt their behavior depending on
the domain of the node they are interacting with.
3.4. Decentralization and Distribution
The goal of Autonomic Networking is to minimize dependencies on
central elements; therefore, decentralization and distribution are
fundamental to the concept. If a problem can be solved in a
distributed manner, it should not be centralized.
In certain cases, it is today operationally preferable to keep a
central repository of information, for example, a user database on an
Authentication, Authorization, and Accounting (AAA) server. An
Autonomic Network should be able to use such central systems, in
order to be deployable. It is possible to distribute such databases
as well, and such efforts should be at least considered. Depending
on the case, distribution may not be simple replication but may
involve more complex interactions and organization.
3.5. Simplification of Autonomic Node Northbound Interfaces
Even in a decentralized solution, certain information flows with
central entities are required. Examples are high-level service
definitions, as well as network status requests, audit information,
logging, and aggregated reporting.
Therefore, nodes in an Autonomic Network require a northbound
interface. However, the design goal is to maintain this interface as
simple and high level as possible.
3.6. Abstraction
An administrator or autonomic management system interacts with an
Autonomic Network on a high level of abstraction. Intent is defined
at a level of abstraction that is much higher than that of typical
configuration parameters, for example, "optimize my network for
energy efficiency". Intent must not be used to convey low-level
commands or concepts, since those are on a different abstraction
level.
Behringer, et al. Informational [Page 8]
RFC 7575 Autonomic Networking June 2015
For example, the administrator should not be exposed to the version
of the IP protocol running in the network.
Also on the reporting and feedback side, an Autonomic Network
abstracts information and provides high-level messages such as "the
link between node x and y is down" (possibly with an identifier for
the specific link, in case of multiple links).
3.7. Autonomic Reporting
An Autonomic Network, while minimizing the need for user
intervention, still needs to provide users with visibility like in
traditional networks. However, in an Autonomic Network, reporting
should happen on a network-wide basis. Information about the network
should be collected and aggregated by the network itself and
presented in a consolidated fashion to the administrator.
The layers of abstraction that are provided via Intent need to be
supported for reporting functions as well, in order to give users an
indication about the effectiveness of their Intent. For example, in
order to assess how effective the network performs with regards to
the Intent "optimize my network for energy efficiency", the network
should provide aggregate information about the number of ports that
were able to be shut down, and the corresponding energy savings,
while validating current service levels are, on aggregate, still met.
Autonomic network events should concern the Autonomic Network as a
whole, not individual systems in isolation. For example, the same
failure symptom should not be reported from every system that
observes it, but only once for the Autonomic Network as a whole.
Ultimately, the Autonomic Network should support exception-based
management, in which only events that truly require user attention
actually cause the user to be notified. This requires capabilities
that allow systems within the network to compare information and
apply specific algorithms to determine what should be reported.
3.8. Common Autonomic Networking Infrastructure
[RFC7576] points out that there are already a number of autonomic
functions available today. However, they are largely independent,
and each has its own methods and protocols to communicate, discover,
define, and distribute policy, etc.
The goal of the work on Autonomic Networking in the IETF is therefore
not just to create autonomic functions but to define a common
infrastructure that autonomic functions can use. This Autonomic
Networking Infrastructure may contain common control and management
Behringer, et al. Informational [Page 9]
RFC 7575 Autonomic Networking June 2015
functions such as messaging, service discovery, negotiation, Intent
distribution, self-monitoring, and diagnostics, etc. A common
approach to define and manage Intent is also required.
Refer to the reference model below: All the components around the
"Autonomic Service Agents" should be common components, such that the
Autonomic Service Agents do not have to replicate common tasks
individually.
3.9. Independence of Function and Layer
Autonomic functions may reside on any layer in the networking stack.
For example, Layer 2 switching today is already relatively autonomic
in many environments, since most switches can be plugged together in
many ways and will automatically build a simple Layer 2 topology.
Routing functions run on a higher layer and can be autonomic on Layer
3. Even application-layer functionality such as unified
communications can be autonomic.
"Autonomic" in the context of this framework is a property of a
function that is implemented on a node. Autonomic functions can be
implemented on any node type, for example, a switch, router, server,
or call manager.
An Autonomic Network requires an overall control plane for autonomic
nodes to communicate. As in general IP networking, IP is the
spanning layer that binds all those elements together; autonomic
functions in the context of this framework should therefore operate
at the IP layer. This concerns neighbor discovery protocols and
other functions in the Autonomic Control Plane.
3.10. Full Life-Cycle Support
An autonomic function does not depend on external input to operate;
it needs to understand its current situation and surroundings and
operate according to its current state. Therefore, an autonomic
function must understand the full life cycle of the device it runs
on, from manufacturing and initial testing through deployment,
testing, troubleshooting, and decommissioning.
The state of the life cycle of an autonomic node is reflected in a
state model. The behavior of an autonomic function may be different
for different deployment states.
Behringer, et al. Informational [Page 10]
RFC 7575 Autonomic Networking June 2015
4. Not among the Design Goals
This section identifies various items that are explicitly not design
goals in the IETF and IRTF for Autonomic Networks; they are mentioned
to avoid misunderstandings of the general intention. They address
some commonly expressed concerns from network administrators and
architects.
4.1. Eliminate Human Operators
Section 3.1 states that "It is the design goal to make functions
[...] minimally dependent on [...] human operators". However, it is
not a design goal to completely eliminate them. The problem targeted
by Autonomic Networking is the error-prone and hard-to-scale model of
individual configuration of network elements, traditionally by manual
commands but today mainly by scripting and/or configuration
management databases. This does not, however, imply the elimination
of skilled human operators, who will still be needed for oversight,
policy management, diagnosis, reaction to help-desk tickets, etc.
The main impact on administrators should be less tedious detailed
work and more high-level work. (They should become more like doctors
than hospital orderlies.)
4.2. Eliminate Emergency Fixes
However good the autonomous mechanisms, sometimes there will be fault
conditions, etc., that they cannot deal with correctly. At that
point, skilled operator interventions will be needed to correct or
work around the problem. Hopefully, this can be done by high-level
mechanisms (adapting the policy database in some way), but, in some
cases, direct intervention at the device level may be unavoidable.
This is obviously the case for hardware failures, even if the
Autonomic Network has bypassed the fault for the time being. "Truck
rolls" will not be eliminated when faulty equipment needs to be
replaced. However, this may be less urgent if the autonomic system
automatically reconfigures to minimize the operational impact.
4.3. Eliminate Central Control
While it is a goal to simplify northbound interfaces (Section 3.5),
it is not a goal to eliminate central control, but to allow it on a
higher abstraction level. Senior management might fear loss of
control of an Autonomic Network. In fact, this is no more likely
than with a traditional network; the emphasis on automatically
applying general policy and security rules might even provide more
central control.
Behringer, et al. Informational [Page 11]
RFC 7575 Autonomic Networking June 2015
5. An Autonomic Reference Model
An Autonomic Network consists of Autonomic Nodes. Those nodes
communicate with each other through an Autonomic Control Plane that
provides a robust and secure communications overlay. The Autonomic
Control Plane is self-organizing and autonomic itself.
An Autonomic Node contains various elements, such as autonomic
service agents that implement autonomic functions. Figure 1 shows a
reference model of an autonomic node. The elements and their
interaction are:
o Autonomic Service Agents: They implement the autonomic behavior of
a specific service or function.
o Self-knowledge: An autonomic node knows its own properties and
capabilities
o Network Knowledge (Discovery): An Autonomic Service Agent may
require various discovery functions in the network, such as
service discovery.
o Feedback Loops: Control elements outside the node may interact
with autonomic nodes through feedback loops.
o An Autonomic User Agent, providing a front-end to external users
(administrators and management applications) through which they
can receive reports and monitor the Autonomic Network.
o Autonomic Control Plane: Allows the node to communicate with other
autonomic nodes. Autonomic functions such as Intent distribution,
feedback loops, discovery mechanisms, etc., use the Autonomic
Control Plane. The Autonomic Control Plane can run in-band, over
a configured VPN, over a self-managing overlay network as
described in [ACP], or over a traditional out-of-band network.
Security is a requirement for the Autonomic Control Plane, which
can be bootstrapped by a mechanism as described in [BOOTSTRAP].
Behringer, et al. Informational [Page 12]
RFC 7575 Autonomic Networking June 2015
+------------------------------------------------------------+
| +------------+ |
| | Feedback | |
| | Loops | |
| +------------+ |
| ^ |
| Autonomic User Agent |
| V |
| +-----------+ +------------+ +------------+ |
| | Self- | | Autonomic | | Network | |
| | knowledge |<------>| Service |<------>| Knowledge | |
| | | | Agents | | (Discovery)| |
| +-----------+ +------------+ +------------+ |
| ^ ^ |
| | | |
| V V |
|------------------------------------------------------------|
| Autonomic Control Plane |
|------------------------------------------------------------|
| Standard Operating System Functions |
+------------------------------------------------------------+
Figure 1: Reference Model for an Autonomic Node
At the time of finalizing this document, this reference model is
being worked out in more detail. See [Reference-Model] for more
details.
6. Security Considerations
This document provides definitions and design goals for Autonomic
Networking. A full threat analysis will be required as part of the
development of solutions, taking account of potential attacks from
within the network as well as from outside.
7. Informative References
[ACP] Behringer, M., Bjarnason, S., BL, B., and T. Eckert, "An
Autonomic Control Plane", Work in Progress,
draft-behringer-anima-autonomic-control-plane-02, March
2015.
[Behringer]
Behringer, M., Pritikin, M., and S. Bjarnason, "Making The
Internet Secure By Default", Work in Progress,
draft-behringer-default-secure-00, January 2014.
Behringer, et al. Informational [Page 13]
RFC 7575 Autonomic Networking June 2015
[BOOTSTRAP]
Pritikin, M., Behringer, M., and S. Bjarnason,
"Bootstrapping Key Infrastructures", Work in Progress,
draft-pritikin-anima-bootstrapping-keyinfra-01, February
2015.
[Dobson] Dobson, S., Denazis, S., Fernandez, A., Gaiti, D.,
Gelenbe, E., Massacci, F., Nixon, P., Saffre, F., Schmidt,
N., and F. Zambonelli, "A survey of autonomic
communications", ACM Transactions on Autonomous and
Adaptive Systems (TAAS), Volume 1, Issue 2, Pages 223-259,
DOI 10.1145/1186778.1186782, December 2006.
[GANA] ETSI, "Autonomic network engineering for the self-managing
Future Internet (AFI); Generic Autonomic Network
Architecture (An Architectural Reference Model for
Autonomic Networking, Cognitive Networking and Self-
Management)", ETSI GS AFI 002, April 2013,
<http://www.etsi.org/deliver/etsi_gs/
AFI/001_099/002/01.01.01_60/gs_afi002v010101p.pdf>.
[Kephart] Kephart, J. and D. Chess, "The Vision of Autonomic
Computing", IEEE Computer, vol. 36, no. 1, pp. 41-50,
DOI 10.1109/MC.2003.1160055, January 2003.
[Movahedi] Movahedi, Z., Ayari, M., Langar, R., and G. Pujolle, "A
Survey of Autonomic Network Architectures and Evaluation
Criteria", IEEE Communications Surveys & Tutorials, Volume
14, Issue 2, Pages 464-490,
DOI 10.1109/SURV.2011.042711.00078, 2012.
[Reference-Model]
Behringer, M., Ed., Carpenter, B., Eckert, T., Ciavaglia,
L., and B. Liu, "A Reference Model for Autonomic
Networking", Work in Progress, draft-behringer-anima-
reference-model-02, June 2015.
[RFC7576] Jiang, S., Carpenter, B., and M. Behringer, "General Gap
Analysis for Autonomic Networking", RFC 7576,
DOI 10.17487/RFC7576, June 2015,
<http://www.rfc-editor.org/info/rfc7576>.
[Samaan] Samaan, N. and A. Karmouch, "Towards Autonomic Network
Management: an Analysis of Current and Future Research
Directions", IEEE Communications Surveys and Tutorials,
Volume 11, Issue 3, Page(s) 22-36,
DOI 10.1109/SURV.2009.090303, 2009.
Behringer, et al. Informational [Page 14]
RFC 7575 Autonomic Networking June 2015
Acknowledgements
Many parts of this work on Autonomic Networking are the result of a
large team project at Cisco Systems. In alphabetical order: Ignas
Bagdonas, Parag Bhide, Balaji BL, Toerless Eckert, Yves Hertoghs,
Bruno Klauser.
We thank the following people for their input to this document:
Dimitri Papadimitriou, Rene Struik, Kostas Pentikousis, Dave Oran,
and Diego Lopez Garcia.
The ETSI working group AFI <http://portal.etsi.org/afi> defines a
similar framework for Autonomic Networking in the "General Autonomic
Network Architecture" [GANA]. Many concepts explained in this
document can be mapped to the GANA framework. The mapping is outside
the scope of this document. Special thanks to Ranganai Chaparadza
for his comments and help on this document.
Authors' Addresses
Michael H. Behringer
Cisco Systems
Building D, 45 Allee des Ormes
Mougins 06250
France
EMail: mbehring@cisco.com
Max Pritikin
Cisco Systems
5330 Airport Blvd
Boulder, CO 80301
United States
EMail: pritikin@cisco.com
Steinthor Bjarnason
Cisco Systems
Mail Stop LYS01/5
Philip Pedersens vei 1
LYSAKER, AKERSHUS 1366
Norway
EMail: sbjarnas@cisco.com
Behringer, et al. Informational [Page 15]
RFC 7575 Autonomic Networking June 2015
Alexander Clemm
Cisco Systems
170 West Tasman Drive
San Jose, CA 95134-1706
United States
EMail: alex@cisco.com
Brian Carpenter
Department of Computer Science
University of Auckland
PB 92019
Auckland 1142
New Zealand
EMail: brian.e.carpenter@gmail.com
Sheng Jiang
Huawei Technologies Co., Ltd
Q14, Huawei Campus
No.156 Beiqing Road
Hai-Dian District, Beijing 100095
China
EMail: jiangsheng@huawei.com
Laurent Ciavaglia
Alcatel Lucent
Route de Villejust
Nozay 91620
France
EMail: laurent.ciavaglia@alcatel-lucent.com
Behringer, et al. Informational [Page 16]