Requirements for Energy Management
RFC 6988
| Document | Type | RFC - Informational (September 2013; No errata) | |
|---|---|---|---|
| Authors | Juergen Quittek , Mouli Chandramouli , Rolf Winter , Thomas Dietz , Benoît Claise | ||
| Last updated | 2018-12-20 | ||
| Stream | Internet Engineering Task Force (IETF) | ||
| Formats | plain text html pdf htmlized bibtex | ||
| Reviews | |||
| Stream | WG state | Submitted to IESG for Publication | |
| Document shepherd | Adrian Farrel | ||
| IESG | IESG state | RFC 6988 (Informational) | |
| Action Holders |
(None)
|
||
| Consensus Boilerplate | Unknown | ||
| Telechat date | |||
| Responsible AD | Joel Jaeggli | ||
| IESG note | Nevil Brownlee (n.brownlee@auckland.ac.nz) is the document shepherd. | ||
| Send notices to | (None) | ||
Internet Engineering Task Force (IETF) J. Quittek, Ed.
Request for Comments: 6988 NEC Europe Ltd.
Category: Informational M. Chandramouli
ISSN: 2070-1721 Cisco Systems, Inc.
R. Winter
T. Dietz
NEC Europe Ltd.
B. Claise
Cisco Systems, Inc.
September 2013
Requirements for Energy Management
Abstract
This document defines requirements for standards specifications for
Energy Management. The requirements defined in this document are
concerned with monitoring functions as well as control functions.
Monitoring functions include identifying energy-managed devices and
their components, as well as monitoring their Power States, Power
Inlets, Power Outlets, actual power, Power Attributes, received
energy, provided energy, and contained batteries. Control functions
include such functions as controlling power supply and Power State of
energy-managed devices and their components.
This document does not specify the features that must be implemented
by compliant implementations but rather lists features that must be
supported by standards for Energy Management.
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6988.
Quittek, et al. Informational [Page 1]
RFC 6988 Requirements for Energy Management September 2013
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction ....................................................3
1.1. Conventional Requirements for Energy Management ............3
1.2. Specific Requirements for Energy Management ................4
2. Terminology .....................................................5
3. General Considerations Related to Energy Management .............6
3.1. Power States ...............................................7
3.2. Saving Energy versus Maintaining Service Level .............7
3.3. Local versus Network-Wide Energy Management ................7
3.4. Energy Monitoring versus Energy Saving .....................8
3.5. Overview of Energy Management Requirements .................8
4. Identification of Entities ......................................9
5. Information on Entities ........................................10
5.1. General Information on Entities ...........................10
5.2. Power Interfaces ..........................................11
5.3. Power .....................................................13
5.4. Power State ...............................................15
5.5. Energy ....................................................17
5.6. Battery State .............................................18
5.7. Time Series of Measured Values ............................19
6. Control of Entities ............................................21
7. Reporting on Other Entities ....................................21
8. Controlling Other Entities .....................................22
8.1. Controlling Power States of Other Entities ................22
8.2. Controlling Power Supply ..................................23
9. Security Considerations ........................................23
10. Acknowledgments ...............................................25
11. References ....................................................25
11.1. Normative References .....................................25
11.2. Informative References ...................................26
Quittek, et al. Informational [Page 2]
RFC 6988 Requirements for Energy Management September 2013
1. Introduction
With rising energy costs and an increasing awareness of the
ecological impact of running information technology equipment, Energy
Management (EMAN) functions and interfaces are becoming an additional
basic requirement for network management systems and devices
connected to a network.
This document defines requirements for standards specifications for
Energy Management, both monitoring functions and control functions.
Energy Management functions focus mainly on devices and their
components that receive and provide electrical energy. Devices such
as hosts, routers, and middleboxes may have an IP address or may be
connected indirectly to the Internet via a proxy with an IP address
providing a management interface for the device, for example, devices
in a building infrastructure using non-IP protocols and a gateway to
the Internet.
These requirements are concerned with the standards specification
process and not the implementation of specified standards. All
requirements in this document must be reflected by standards
specifications to be developed. However, which of the features
specified by these standards will be mandatory, recommended, or
optional for compliant implementations is to be defined by Standards
Track document(s) and not in this document.
Section 3 elaborates on a set of general needs for Energy Management.
Requirements for an Energy Management standard are specified in
Sections 4 through 8.
Sections 4 through 6 contain conventional requirements specifying
information on entities and control functions.
Sections 7 and 8 contain requirements specific to Energy Management.
Due to the nature of power supply, some monitoring and control
functions are not conducted by interacting with the entity of
interest but rather with other entities, for example, entities
upstream in a power distribution tree.
1.1. Conventional Requirements for Energy Management
The specification of requirements for an Energy Management standard
starts with Section 4, which addresses the identification of entities
and the granularity of reporting of energy-related information. A
standard must support the unique identification of entities,
reporting per entire device, and reporting energy-related information
on individual components of a device or attached devices.
Quittek, et al. Informational [Page 3]
RFC 6988 Requirements for Energy Management September 2013
Section 5 specifies requirements related to the monitoring of
entities. This includes general (type, context) information and
specific information on Power States, Power Inlets, Power Outlets,
power, energy, and batteries. The control of Power State and power
supply by entities is covered by requirements specified in Section 6.
1.2. Specific Requirements for Energy Management
While the conventional requirements summarized above seem to be all
that would be needed for Energy Management, there are significant
differences between Energy Management and most well-known network
management functions. The most significant difference is the need
for some devices to report on other entities. There are three major
reasons for this.
o For monitoring a particular entity, it is not always sufficient to
communicate only with that entity. When the entity has no
instrumentation for determining power, it might still be possible
to obtain power values for the entity via communication with other
entities in its power distribution tree. A simple example of this
would be the retrieval of power values from a power meter at the
power line into the entity. A Power Distribution Unit (PDU) and a
Power over Ethernet (PoE) switch are common examples. Both supply
power to other entities at sockets or ports, respectively, and are
often instrumented to measure power per socket or port.
o Similar considerations apply to controlling the power supply of an
entity that often needs direct or indirect communications with
another entity upstream in the power distribution tree. Again, a
PDU and a PoE switch are common examples, if they have the
capability to switch power on or off at their sockets or ports,
respectively.
o Energy Management often extends beyond entities with IP network
interfaces to non-IP building systems accessed via a gateway
(sometimes called an Energy Management System or controller).
Requirements in this document do not cover the details of these
networks and energy devices but specify means for opening IP
network management towards them.
These specific issues of Energy Management, as well as other issues,
are covered by requirements specified in Sections 7 and 8.
The requirements in these sections need a new Energy Management
framework that deals with the specific nature of Energy Management.
The actual standards documents, such as MIB module specifications,
address conformance by specifying which features must, should, or may
be implemented by compliant implementations.
Quittek, et al. Informational [Page 4]
RFC 6988 Requirements for Energy Management September 2013
2. Terminology
The terms specified in the terminology section are capitalized
throughout the document; the exceptions are the well-known terms
"energy" and "power". These terms are generic and are used in
generated terms such as "energy-saving", "low-power", etc.
Energy
Energy is the capacity of a system to do work. As used by
electric utilities, it is generally a reference to electrical
energy and is measured in kilowatt-hours (kWh) [IEEE-100].
Power
Power is the time rate at which energy is emitted, transferred, or
received; power is usually expressed in watts (or in joules per
second) [IEEE-100]. (The term "power" does not refer to the
concept of demand, which is an averaged power value.)
Power Attributes
Power Attributes are measurements of electric current, voltage,
phase, and frequencies at a given point in an electrical power
system (adapted from [IEC.60050]).
NOTE: Power Attributes are not intended to be "judgmental" with
respect to a reference or technical value and are independent of
any usage context.
Energy Management
Energy Management is a set of functions for measuring, modeling,
planning, and optimizing networks to ensure that the network
elements and attached devices use energy efficiently and in a
manner appropriate to the nature of the application and the cost
constraints of the organization [ITU-M.3400].
Energy Management System
An Energy Management System is a combination of hardware and
software used to administer a network with the primary purpose
being Energy Management.
Quittek, et al. Informational [Page 5]
RFC 6988 Requirements for Energy Management September 2013
Energy Monitoring
Energy Monitoring is a part of Energy Management that deals with
collecting or reading information from network elements and
attached devices and their components to aid in Energy Management.
Energy Control
Energy Control is a part of Energy Management that deals with
controlling energy supply and Power State of network elements, as
well as attached devices and their components.
Power Interface
A Power Interface is an interface at which a device is connected
to a power transmission medium, at which it can in turn receive
power, provide power, or both.
Power Inlet
A Power Inlet is a Power Interface at which a device can receive
power from other devices.
Power Outlet
A Power Outlet is a Power Interface at which a device can provide
power to other devices.
Power State
A Power State is a condition or mode of a device that broadly
characterizes its capabilities, power consumption, and
responsiveness to input [IEEE-1621].
3. General Considerations Related to Energy Management
The basic objective of Energy Management is to operate sets of
devices using minimal energy, while maintaining a certain level of
service. [EMAN-STATEMENT] presents the applicability of the EMAN
framework to a variety of scenarios and also lists use cases and
target devices.
Quittek, et al. Informational [Page 6]
RFC 6988 Requirements for Energy Management September 2013
3.1. Power States
Entities can be set to an operational state that results in the
lowest power level that still meets the service-level performance
objectives. In principle, there are three basic types of Power
States for an entity or for a whole system:
o full Power State
o sleep state (not functional but immediately available)
o off state (may require significant time to become operational)
In specific devices, the number of Power States and their properties
vary considerably. Simple entities may only have the extreme states:
full Power State and off state. Many devices have three basic Power
States: on, off, and sleep. However, more finely grained Power
States can be implemented. Examples are various operational low
Power States in which a device requires less energy than in the full
power "on" state, but -- compared to the sleep state -- is still
operational with reduced performance or functionality.
3.2. Saving Energy versus Maintaining Service Level
One of the objectives of Energy Management is to reduce energy
consumption. While this objective is clear, attaining that goal is
often difficult. In many cases, there is no way to reduce power
without the consequence of a potential service (performance or
capacity) degradation. In this case, a trade-off needs to be made
between service-level objectives and energy minimization. In other
cases, a reduction of power can easily be achieved while still
maintaining sufficient service-level performance, for example, by
switching entities to lower Power States when higher performance is
not needed.
3.3. Local versus Network-Wide Energy Management
Many energy-saving functions are executed locally by an entity; it
monitors its usage and dynamically adapts its power according to the
required performance. It may, for example, switch to a sleep state
when it is not in use, or outside of scheduled business hours. An
Energy Management System may observe an entity's Power State and
configure its power-saving policies.
Energy savings can also be achieved with policies implemented by a
network management system that controls Power States of managed
entities. Information about the power received and provided by
Quittek, et al. Informational [Page 7]
RFC 6988 Requirements for Energy Management September 2013
entities in different Power States may be required in order to set
such policies. Often, this information is best acquired through
monitoring.
Network-wide and local Energy Management methods both have advantages
and disadvantages, and it is often desirable to combine them.
Central management is often favorable for setting Power States of a
large number of entities at the same time, for example, at the
beginning and end of business hours in a building. Local management
is often preferable for power-saving measures based on local
observations, such as the high or low functional load of an entity.
3.4. Energy Monitoring versus Energy Saving
Monitoring energy, power, and Power States alone does not reduce the
energy needed to run an entity. In fact, it may even increase it
slightly due to monitoring instrumentation that needs energy.
Reporting measured quantities over the network may also increase
energy use, though the acquired information may be an essential input
to control loops that save energy.
Monitoring energy and Power States can also be required for other
purposes, including:
o investigating energy-saving potential
o evaluating the effectiveness of energy-saving policies and
measures
o deriving, implementing, and testing power management strategies
o accounting for the total power received and provided by an entity,
a network, or a service
o predicting an entity's reliability based on power usage
o choosing the time of the next maintenance cycle for an entity
3.5. Overview of Energy Management Requirements
The following basic management functions are required:
o monitoring Power States
o monitoring power (energy conversion rate)
o monitoring (accumulated) received and provided energy
Quittek, et al. Informational [Page 8]
RFC 6988 Requirements for Energy Management September 2013
o monitoring Power Attributes
o setting Power States
Power control is complementary to other energy-saving measures, such
as low-power electronics, energy-saving protocols, energy-efficient
device design (for example, low-power modes for components), and
energy-efficient network architectures. Measurement of received and
provided energy can provide useful data for developing these
technologies.
4. Identification of Entities
Entities must be capable of being uniquely identified within the
context of the management system. This includes entities that are
components of managed devices as well as entire devices.
Entities that report on or control other entities must identify the
entities they report on or control: see Section 7 or Section 8,
respectively, for the detailed requirements.
An entity may be an entire device or a component of it. Examples of
components of interest are a hard drive, a battery, or a line card.
The ability to control individual components to save energy may be
required. For example, server blades can be switched off when the
overall load is low, or line cards at switches may be powered down at
night.
Identifiers for devices and components are already defined in
standard MIB modules, such as the Link Layer Discovery Protocol
(LLDP) MIB module [IEEE-802.1AB] and the Link Layer Discovery
Protocol -- Media Endpoint Discovery (LLDP-MED) MIB module
[ANSI-TIA-1057] for devices, and the Entity MIB module [RFC6933] and
the power Ethernet MIB [RFC3621] for components of devices. Energy
Management needs a means to link energy-related information to such
identifiers.
Instrumentation for measuring the received and provided energy of a
device is typically more expensive than instrumentation for
retrieving its Power State. Many devices may provide Power State
information for all individual components separately, while reporting
the received and provided energy only for the entire device.
4.1. Identifying Entities
The standard must provide means for uniquely identifying entities.
Uniqueness must be preserved such that collisions of identities are
avoided at potential receivers of monitored information.
Quittek, et al. Informational [Page 9]
RFC 6988 Requirements for Energy Management September 2013
4.2. Persistence of Identifiers
The standard must provide means for indicating whether identifiers of
entities are persistent across a restart of the entity.
4.3. Change of Identifiers
The standard must provide means to indicate any change of entity
identifiers.
4.4. Using Entity Identifiers of Existing MIB Modules
The standard must provide means for reusing entity identifiers from
existing standards, including at least the following:
o the entPhysicalIndex in the Entity MIB module [RFC6933]
o the LldpPortNumber in the LLDP MIB module [IEEE-802.1AB] and in
the LLDP-MED MIB module [ANSI-TIA-1057]
o the pethPsePortIndex and the pethPsePortGroupIndex in the Power
Ethernet MIB [RFC3621]
Generic means for reusing other entity identifiers must be provided.
5. Information on Entities
This section describes information on entities for which the standard
must provide means for retrieving and reporting.
Required information can be structured into seven groups.
Section 5.1 specifies requirements for general information on
entities, such as type of entity or context information.
Requirements for information on Power Inlets and Power Outlets of
entities are specified in Section 5.2. The monitoring of power and
energy is covered by Sections 5.3 and 5.5, respectively. Section 5.4
covers requirements related to entities' Power States. Section 5.6
specifies requirements for monitoring batteries. Finally, the
reporting of time series of values is covered by Section 5.7.
5.1. General Information on Entities
For Energy Management, understanding the role and context of an
entity may be required. An Energy Management System may aggregate
values of received and provided energy according to a defined
grouping of entities. When controlling and setting Power States, it
may be helpful to understand the grouping of the entity and role of
Quittek, et al. Informational [Page 10]
RFC 6988 Requirements for Energy Management September 2013
an entity in a network. For example, it may be important to exclude
some mission-critical network devices from being switched to lower
power or even from being switched off.
5.1.1. Type of Entity
The standard must provide means to configure, retrieve, and report a
textual name or a description of an entity.
5.1.2. Context of an Entity
The standard must provide means for retrieving and reporting context
information on entities, for example, tags associated with an entity
that indicate the entity's role.
5.1.3. Significance of Entities
The standard must provide means for retrieving and reporting the
significance of entities within its context, for example, how
important the entity is.
5.1.4. Power Priority
The standard must provide means for retrieving and reporting power
priorities of entities. Power priorities indicate an order in which
Power States of entities are changed, for example, to lower Power
States for saving power.
5.1.5. Grouping of Entities
The standard must provide means for grouping entities. This can be
achieved in multiple ways, for example, by providing means to tag
entities, assign them to domains, or assign device types to them.
5.2. Power Interfaces
A Power Interface is an interface at which a device is connected to a
power transmission medium, at which it can in turn receive power,
provide power, or both.
A Power Interface is either an inlet or an outlet. Some Power
Interfaces change over time from being an inlet to being an outlet
and vice versa. However, most Power Interfaces never change.
Devices have Power Inlets at which they are supplied with electric
power. Most devices have a single Power Inlet, while some have
multiple inlets. Different Power Inlets on a device are often
connected to separate power distribution trees. For Energy
Quittek, et al. Informational [Page 11]
RFC 6988 Requirements for Energy Management September 2013
Monitoring, it is useful to retrieve information on the number of
inlets of a device, the availability of power at inlets, and which
inlets are actually in use.
Devices can have one or more Power Outlets for supplying other
devices with electric power.
For identifying and potentially controlling the source of power
received at an inlet, identifying the Power Outlet of another device
at which the received power is provided may be required.
Analogously, for each outlet, it is of interest to identify the Power
Inlets that receive the power provided at a certain outlet. Such
information is also required for constructing the wiring topology of
electrical power distribution to devices.
Static properties of each Power Interface are required information
for Energy Management. Static properties include the kind of
electric current (AC or DC), the nominal voltage, the nominal AC
frequency, and the number of AC phases. Note that the nominal
voltage is often not a single value but a voltage range, such as, for
example, (100V-120V), (100V-240V), (100V-120V,220V-240V).
5.2.1. List of Power Interfaces
The standard must provide means for monitoring the list of Power
Interfaces of a device.
5.2.2. Operational Mode of Power Interfaces
The standard must provide means for monitoring the operational mode
of a Power Interface, which is either "Power Inlet" or "Power
Outlet".
5.2.3. Corresponding Power Outlet
The standard must provide means for identifying the Power Outlet that
provides the power received at a Power Inlet.
5.2.4. Corresponding Power Inlets
The standard must provide means for identifying the list of Power
Inlets that receive the power provided at a Power Outlet.
Quittek, et al. Informational [Page 12]
RFC 6988 Requirements for Energy Management September 2013
5.2.5. Availability of Power
If the Power States allow it, the standard must provide means for
monitoring the availability of power at each Power Interface. This
includes indicating whether a power supply at a Power Interface is
switched on or off.
5.2.6. Use of Power
The standard must provide means for monitoring each Power Interface
if it is actually in use. For inlets, this means that the device
actually receives power at the inlet. For outlets, this means that
power is actually provided from the outlet to one or more devices.
5.2.7. Type of Current
The standard must provide means for reporting the type of current (AC
or DC) for each Power Interface as well as for a device.
5.2.8. Nominal Voltage Range
The standard must provide means for reporting the nominal voltage
range for each Power Interface.
5.2.9. Nominal AC Frequency
The standard must provide means for reporting the nominal AC
frequency for each Power Interface.
5.2.10. Number of AC Phases
The standard must provide means for reporting the number of AC phases
for each Power Interface.
5.3. Power
Power is measured as an instantaneous value or as the average over a
time interval.
Obtaining highly accurate values for power and energy may be costly
if dedicated metering hardware is required. Entities without the
ability to measure with high accuracy their power, received energy,
and provided energy may just report estimated values, for example,
based on load monitoring, Power State, or even just the entity type.
Depending on how power and energy values are obtained, the confidence
in a reported value and its accuracy will vary. Entities reporting
such values should qualify the confidence in the reported values and
Quittek, et al. Informational [Page 13]
RFC 6988 Requirements for Energy Management September 2013
quantify the accuracy of measurements. For reporting accuracy, the
accuracy classes specified in IEC 62053-21 [IEC.62053-21] and
IEC 62053-22 [IEC.62053-22] should be considered.
Further properties of the power supplied to a device are also of
interest. For AC power supply in particular, several Power
Attributes beyond the real power are of potential interest to Energy
Management Systems. The set of these properties includes the complex
Power Attributes (apparent power, reactive power, and phase angle of
the current or power factor) as well as the actual voltage, the
actual AC frequency, the Total Harmonic Distortion (THD) of voltage
and current, and the impedance of an AC phase or of the DC supply. A
new standard for monitoring these Power Attributes should be in line
with already-existing standards, such as [IEC.61850-7-4].
For some network management tasks, it is desirable to receive
notifications from entities when their power value exceeds or falls
below given thresholds.
5.3.1. Real Power / Power Factor
The standard must provide means for reporting the real power for each
Power Interface as well as for an entity. Reporting power includes
reporting the direction of power flow.
5.3.2. Power Measurement Interval
The standard must provide means for reporting the corresponding time
or time interval for which a power value is reported. The power
value can be measured at the corresponding time or averaged over the
corresponding time interval.
5.3.3. Power Measurement Method
The standard must provide means to indicate the method used to obtain
these values. Based on how the measurement was conducted, it is
possible to associate a certain degree of confidence with the
reported power value. For example, there are methods of measurement
such as direct power measurement, estimation based on performance
values, or hard-coding average power values for an entity.
5.3.4. Accuracy of Power and Energy Values
The standard must provide means for reporting the accuracy of
reported power and energy values.
Quittek, et al. Informational [Page 14]
RFC 6988 Requirements for Energy Management September 2013
5.3.5. Actual Voltage and Current
The standard must provide means for reporting the actual voltage and
actual current for each Power Interface as well as for a device. For
AC power supply, means must be provided for reporting the actual
voltage and actual current per phase.
5.3.6. High-Power/Low-Power Notifications
The standard must provide means for creating notifications if power
values of an entity rise above or fall below given thresholds.
5.3.7. Complex Power / Power Factor
The standard must provide means for reporting the complex power for
each Power Interface and for each phase at a Power Interface. In
addition to the real power, at least two of the following three
quantities need to be reported: apparent power, reactive power, and
phase angle. The phase angle can be substituted by the power factor.
5.3.8. Actual AC Frequency
The standard must provide means for reporting the actual AC frequency
for each Power Interface.
5.3.9. Total Harmonic Distortion
The standard must provide means for reporting the Total Harmonic
Distortion (THD) of voltage and current for each Power Interface.
For AC power supply, means must be provided for reporting the THD per
phase.
5.3.10. Power Supply Impedance
The standard must provide means for reporting the impedance of a
power supply for each Power Interface. For AC power supply, means
must be provided for reporting the impedance per phase.
5.4. Power State
Many entities have a limited number of discrete Power States.
There is a need to report the actual Power State of an entity and to
provide the means for retrieving the list of all supported Power
States.
Quittek, et al. Informational [Page 15]
RFC 6988 Requirements for Energy Management September 2013
Different standards bodies have already defined sets of Power States
for some entities, and others are creating new Power State sets. In
this context, it is desirable that the standard support many of these
Power State standards. In order to support multiple management
systems that possibly use different Power State sets while
simultaneously interfacing with a particular entity, the Energy
Management System must provide means for supporting multiple Power
State sets used simultaneously at an entity.
Power States have parameters that describe their properties. It is
required to have a standardized means for reporting some key
properties, such as the typical power of an entity in a certain
state.
There is also a need to report statistics on Power States, including
the time spent as well as the received and provided energy in a Power
State.
5.4.1. Actual Power State
The standard must provide means for reporting the actual Power State
of an entity.
5.4.2. List of Supported Power States
The standard must provide means for retrieving the list of all
potential Power States of an entity.
5.4.3. Multiple Power State Sets
The standard must provide means for supporting multiple Power State
sets simultaneously at an entity.
5.4.4. List of Supported Power State Sets
The standard must provide means for retrieving the list of all Power
State sets supported by an entity.
5.4.5. List of Supported Power States within a Set
The standard must provide means for retrieving the list of all
potential Power States of an entity for each supported Power State
set.
5.4.6. Typical Power Per Power State
The standard must provide means for retrieving the typical power for
each supported Power State.
Quittek, et al. Informational [Page 16]
RFC 6988 Requirements for Energy Management September 2013
5.4.7. Power State Statistics
The standard must provide means for monitoring statistics per Power
State, including the total time spent in a Power State, the number of
times each state was entered, and the last time each state was
entered. More Power State statistics are addressed by the
requirements in Section 5.5.3.
5.4.8. Power State Changes
The standard must provide means for generating a notification when
the actual Power State of an entity changes.
5.5. Energy
The monitoring of electrical energy received or provided by an entity
is a core function of Energy Management. Since energy is an
accumulated quantity, it is always reported for a certain interval of
time. This can be, for example, the time from the last restart of
the entity to the reporting time, the time from another past event to
the reporting time, the last given amount of time before the
reporting time, or a certain interval specified by two timestamps in
the past.
It is useful for entities to record their received and provided
energy per Power State and report these quantities.
5.5.1. Energy Measurement
The standard must provide means for reporting measured values of
energy and the direction of the energy flow received or provided by
an entity. The standard must also provide the means to report the
energy passing through each Power Interface.
5.5.2. Time Intervals
The standard must provide means for reporting the time interval for
which an energy value is reported.
5.5.3. Energy Per Power State
The standard must provide means for reporting the received and
provided energy for each individual Power State. This extends the
requirements on Power State statistics described in Section 5.4.7.
Quittek, et al. Informational [Page 17]
RFC 6988 Requirements for Energy Management September 2013
5.6. Battery State
Batteries are special entities that supply power. The status of
these batteries is typically controlled by automatic functions that
act locally on the entity, and manually by users of the entity.
There is a need to monitor the battery status of these entities by
network management systems.
Devices containing batteries can be modeled in two ways. The entire
device can be modeled as a single entity on which energy-related
information is reported, or the battery can be modeled as an
individual entity for which energy-related information is monitored
individually according to requirements in Sections 5.1 through 5.5.
Further information on batteries is of interest for Energy
Management, such as the current charge of the battery, the number of
completed charging cycles, the charging state of the battery, its
temperature, and additional static and dynamic battery properties.
It is desirable to receive notifications if the charge of a battery
becomes very low or if a battery needs to be replaced.
5.6.1. Battery Charge
The standard must provide means for reporting the current charge of a
battery, in units of milliampere-hours (mAh).
5.6.2. Battery Charging State
The standard must provide means for reporting the charging state
(charging, discharging, etc.) of a battery.
5.6.3. Battery Charging Cycles
The standard must provide means for reporting the number of completed
charging cycles of a battery.
5.6.4. Actual Battery Capacity
The standard must provide means for reporting the actual capacity of
a battery.
5.6.5. Actual Battery Temperature
The standard must provide means for reporting the actual temperature
of a battery.
Quittek, et al. Informational [Page 18]
RFC 6988 Requirements for Energy Management September 2013
5.6.6. Static Battery Properties
The standard must provide means for reporting static properties of a
battery, including the nominal capacity, the number of cells, the
nominal voltage, and the battery technology.
5.6.7. Low Battery Charge Notification
The standard must provide means for generating a notification when
the charge of a battery decreases below a given threshold. Note that
the threshold may depend on the battery technology.
5.6.8. Battery Replacement Notification
The standard must provide means for generating a notification when
the number of charging cycles of a battery exceeds a given threshold.
5.6.9. Multiple Batteries
If the battery technology allows, the standard must provide means for
meeting requirements in Sections 5.6.1 through 5.6.8 for each
individual battery contained in a single entity.
5.7. Time Series of Measured Values
For some network management tasks, obtaining time series of measured
values from entities, such as power, energy, battery charge, etc., is
required.
In general, time series measurements could be obtained in many
different ways. Means should be provided to either push such values
from the location where they are available to the management system
or to have them stored locally for a sufficiently long period of time
such that a management system can retrieve the full time series.
The following issues are to be considered when designing time series
measurement and reporting functions:
1. Which quantities should be reported?
2. Which time interval type should be used (total, delta, sliding
window)?
3. Which measurement method should be used (sampled, continuous)?
4. Which reporting model should be used (push or pull)?
Quittek, et al. Informational [Page 19]
RFC 6988 Requirements for Energy Management September 2013
The most discussed and probably most needed quantity is energy. But
a need for others, such as power and battery charge, can be
identified as well.
There are three time interval types under discussion for accumulated
quantities such as energy. They can be reported as total values,
accumulated between the last restart of the measurement and a certain
timestamp. Alternatively, energy can be reported as delta values
between two consecutive timestamps. Another alternative is reporting
values for sliding windows as specified in [IEC.61850-7-4].
For non-accumulative quantities, such as power, different measurement
methods are considered. Such quantities can be reported using values
sampled at certain timestamps or, alternatively, by mean values for
these quantities averaged between two (consecutive) timestamps or
over a sliding window.
Finally, time series can be reported using different reporting
models, particularly push-based or pull-based. Push-based reporting
can, for example, be realized by reporting power or energy values
using the IP Flow Information Export (IPFIX) protocol [RFC7011]
[RFC7012]. The Simple Network Management Protocol (SNMP) [RFC3411]
is an example of a protocol that can be used for realizing pull-based
reporting of time series.
For reporting time series of measured values, the following
requirements have been identified. Further decisions concerning
issues discussed above need to be made when developing concrete
Energy Management standards.
5.7.1. Time Series of Energy Values
The standard must provide means for reporting time series of energy
values. If the comparison of time series between multiple entities
is required, then time synchronization between those entities must be
provided (for example, with the Network Time Protocol [RFC5905]).
5.7.2. Time Series Interval Types
The standard must provide means for supporting alternative interval
types. The requirement in Section 5.5.2 applies to every reported
time value.
5.7.3. Time Series Storage Capacity
The standard should provide means for reporting the number of values
of a time series that can be stored for later reporting.
Quittek, et al. Informational [Page 20]
RFC 6988 Requirements for Energy Management September 2013
6. Control of Entities
Many entities control their Power State locally. Other entities need
interfaces for an Energy Management System to control their Power
State.
A power supply is typically not self-managed by devices, and control
of a power supply is typically not conducted as an interaction
between an Energy Management System and the device itself. It is
rather an interaction between the management system and a device
providing power at its Power Outlets. Similar to Power State
control, power supply control may be policy driven. Note that
shutting down the power supply abruptly may have severe consequences
for the device.
6.1. Controlling Power States
The standard must provide means for setting Power States of entities.
6.2. Controlling Power Supply
The standard must provide means for switching a power supply off or
turning a power supply on at Power Interfaces providing power to one
or more devices.
7. Reporting on Other Entities
As discussed in Section 5, not all energy-related information may be
available at the entity in question. Such information may be
provided by other entities. This section covers only the reporting
of information. See Section 8 for requirements on controlling other
entities.
There are cases where a power supply unit switches power for several
entities by turning power on or off at a single Power Outlet or where
a power meter measures the accumulated power of several entities at a
single power line. Consequently, it should be possible to report
that a monitored value does not relate to just a single entity but is
an accumulated value for a set of entities. All of the entities
belonging to that set need to be identified.
7.1. Reports on Other Entities
The standard must provide means for an entity to report information
on another entity.
Quittek, et al. Informational [Page 21]
RFC 6988 Requirements for Energy Management September 2013
7.2. Identity of Other Entities on Which Information Is Reported
For entities that report on one or more other entities, the standard
must provide means for reporting the identity of other entities on
which information is reported. Note that, in some situations, a
manual configuration might be required to populate this information.
7.3. Reporting Quantities Accumulated over Multiple Entities
The standard must provide means for reporting the list of all
entities from which contributions are included in an accumulated
value.
7.4. List of All Entities on Which Information Is Reported
For entities that report on one or more other entities, the standard
must provide means for reporting the complete list of all those
entities on which energy-related information can be reported.
7.5. Content of Reports on Other Entities
For entities that report on one or more other entities, the standard
must provide means for indicating what type or types of energy-
related information can be reported, and for which entities.
8. Controlling Other Entities
This section specifies requirements for controlling Power States and
power supply of entities by communicating with other entities that
have the means for doing that control.
8.1. Controlling Power States of Other Entities
Some entities have control over Power States of other entities. For
example, a gateway to a building system may have the means to control
the Power State of entities in the building that do not have an IP
interface. For this scenario and other similar cases, a way to make
this control accessible to the Energy Management System is needed.
In addition, it is required that an entity that has its state
controlled by other entities has the means to report the list of
these other entities.
Quittek, et al. Informational [Page 22]
RFC 6988 Requirements for Energy Management September 2013
8.1.1. Control of Power States of Other Entities
The standard must provide means for an Energy Management System to
send Power State control commands to an entity that controls the
Power States of entities other than the entity to which the command
was sent.
8.1.2. Identity of Other Power State Controlled Entities
The standard must provide means for reporting the identities of the
entities for which the reporting entity has the means to control
their Power States. Note that, in some situations, a manual
configuration might be required to populate this information.
8.1.3. List of All Power State Controlled Entities
The standard must provide means for an entity to report the list of
all entities for which it can control the Power State.
8.1.4. List of All Power State Controllers
The standard must provide means for an entity that receives commands
controlling its Power State from other entities to report the list of
all those entities.
8.2. Controlling Power Supply
Some entities may have control of the power supply of other entities,
for example, because the other entity is supplied via a Power Outlet
of the entity. For this and similar cases, means are needed to make
this control accessible to the Energy Management System. This need
is already addressed by the requirement in Section 6.2.
In addition, it is required that an entity that has its supply
controlled by other entities has the means to report the list of
these other entities. This need is already addressed by requirements
in Sections 5.2.3 and 5.2.4.
9. Security Considerations
Controlling Power State and power supply of entities are considered
highly sensitive actions, since they can significantly affect the
operation of directly and indirectly connected devices. Therefore,
all control actions addressed in Sections 6 and 8 must be
sufficiently protected through authentication, authorization, and
integrity protection mechanisms.
Quittek, et al. Informational [Page 23]
RFC 6988 Requirements for Energy Management September 2013
Entities that are not sufficiently secure to operate directly on the
public Internet do exist and can be a significant cause of risk, for
example, if the remote control functions described in Sections 6 and
8 can be exercised on those devices from anywhere on the Internet.
The standard needs to provide means for dealing with such cases. One
solution is providing means that allow the isolation of such devices,
e.g., behind a sufficiently secured gateway. Another solution is to
allow compliant implementations to disable sensitive functions, or to
not implement such functions at all.
The monitoring of energy-related quantities of an entity as addressed
in Sections 5 through 8 can be used to derive more information than
just the received and provided energy; therefore, monitored data
requires protection. This protection includes authentication and
authorization of entities requesting access to monitored data as well
as confidentiality protection during transmission of monitored data.
Privacy of stored data in an entity must be taken into account.
Monitored data may be used as input to control, accounting, and other
actions, so integrity of transmitted information and authentication
of the origin may be needed.
9.1. Secure Energy Management
The standard must provide privacy, integrity, and authentication
mechanisms for all actions addressed in Sections 5 through 8. The
security mechanisms must meet the security requirements detailed in
Section 1.4 of [RFC3411].
9.2. Isolation of Insufficiently Secure Entities
The standard must provide means to allow the isolation of entities
that are not sufficiently secure to operate on the public Internet,
e.g., behind a gateway that implements sufficient security that the
vulnerable entities are not directly exposed to the Internet.
9.3. Optional Restriction of Functions
The standard must allow compliant implementations to disable
sensitive functions, or to not implement such functions at all, when
operating in environments that are not sufficiently secured. This
applies particularly to the control functions described in Sections 6
and 8.
Quittek, et al. Informational [Page 24]
RFC 6988 Requirements for Energy Management September 2013
10. Acknowledgments
The authors would like to thank Ralf Wolter for his first essay on
this document. Many thanks to William Mielke, John Parello,
JinHyeock Choi, Georgios Karagiannis, and Michael Suchoff for their
helpful comments on the document. Many thanks to Stephen Farrell,
Robert Sparks, Adrian Farrel, Barry Leiba, Brian Haberman, Peter
Resnick, Sean Turner, Stewart Bryant, and Ralph Droms for their IESG
reviews. Finally, special thanks to the document shepherd, Nevil
Brownlee, and to the EMAN working group chairs: Nevil Brownlee and
Bruce Nordman.
11. References
11.1. Normative References
[ANSI-TIA-1057]
Telecommunications Industry Association, ANSI-
TIA-1057-2006, "TIA Standard -- Telecommunications -- IP
Telephony Infrastructure -- Link Layer Discovery Protocol
for Media Endpoint Devices", April 2006.
[IEC.61850-7-4]
International Electrotechnical Commission, "Communication
networks and systems for power utility automation --
Part 7-4: Basic communication structure -- Compatible
logical node classes and data object classes", March 2010.
[IEC.62053-21]
International Electrotechnical Commission, "Electricity
metering equipment (a.c.) -- Particular requirements --
Part 21: Static meters for active energy (classes 1
and 2)", January 2003.
[IEC.62053-22]
International Electrotechnical Commission, "Electricity
metering equipment (a.c.) -- Particular requirements --
Part 22: Static meters for active energy (classes 0,2 S
and 0,5 S)", January 2003.
[IEEE-100] IEEE, "The Authoritative Dictionary of IEEE Standards
Terms, IEEE 100, Seventh Edition", December 2000.
[IEEE-1621]
Institute of Electrical and Electronics Engineers,
"IEEE 1621-2004 - IEEE Standard for User Interface
Elements in Power Control of Electronic Devices Employed
in Office/Consumer Environments", 2004.
Quittek, et al. Informational [Page 25]
RFC 6988 Requirements for Energy Management September 2013
[IEEE-802.1AB]
IEEE Computer Society, "IEEE Std 802.1AB-2009 -- IEEE
Standard for Local and Metropolitan Area Networks --
Station and Media Access Control Discovery",
September 2009.
[RFC3411] Harrington, D., Presuhn, R., and B. Wijnen, "An
Architecture for Describing Simple Network Management
Protocol (SNMP) Management Frameworks", STD 62, RFC 3411,
December 2002.
[RFC3621] Berger, A. and D. Romascanu, "Power Ethernet MIB",
RFC 3621, December 2003.
[RFC6933] Bierman, A., Romascanu, D., Quittek, J., and M.
Chandramouli, "Entity MIB (Version 4)", RFC 6933,
May 2013.
11.2. Informative References
[EMAN-STATEMENT]
Schoening, B., Chandramouli, M., and B. Nordman, "Energy
Management (EMAN) Applicability Statement", Work in
Progress, April 2013.
[IEC.60050]
International Electrotechnical Commission, "Electropedia:
The World's Online Electrotechnical Vocabulary", 2013,
<http://www.electropedia.org/iev/iev.nsf/
welcome?openform>.
[ITU-M.3400]
International Telecommunication Union, "ITU-T
Recommendation M.3400 -- Series M: TMN and Network
Maintenance: International Transmission Systems, Telephone
Circuits, Telegraphy, Facsimile and Leased Circuits --
Telecommunications Management Network - TMN management
functions", February 2000.
[RFC7011] Claise, B., Ed., Trammell, B., Ed., and P. Aitken,
"Specification of the IP Flow Information Export (IPFIX)
Protocol for the Exchange of Flow Information", STD 77,
RFC 7011, September 2013.
[RFC7012] Claise, B., Ed., and B. Trammell, Ed., "Information Model
for IP Flow Information Export (IPFIX)", RFC 7012,
September 2013.
Quittek, et al. Informational [Page 26]
RFC 6988 Requirements for Energy Management September 2013
[RFC5905] Mills, D., Martin, J., Burbank, J., and W. Kasch, "Network
Time Protocol Version 4: Protocol and Algorithms
Specification", RFC 5905, June 2010.
Authors' Addresses
Juergen Quittek (editor)
NEC Europe Ltd.
NEC Laboratories Europe
Network Research Division
Kurfuersten-Anlage 36
Heidelberg 69115
Germany
Phone: +49 6221 4342-115
EMail: quittek@neclab.eu
Mouli Chandramouli
Cisco Systems, Inc.
Sarjapur Outer Ring Road
Bangalore
India
Phone: +91 80 4426 3947
EMail: moulchan@cisco.com
Rolf Winter
NEC Europe Ltd.
NEC Laboratories Europe
Network Research Division
Kurfuersten-Anlage 36
Heidelberg 69115
Germany
Phone: +49 6221 4342-121
EMail: Rolf.Winter@neclab.eu
Quittek, et al. Informational [Page 27]
RFC 6988 Requirements for Energy Management September 2013
Thomas Dietz
NEC Europe Ltd.
NEC Laboratories Europe
Network Research Division
Kurfuersten-Anlage 36
Heidelberg 69115
Germany
Phone: +49 6221 4342-128
EMail: Thomas.Dietz@neclab.eu
Benoit Claise
Cisco Systems, Inc.
De Kleetlaan 6a b1
Diegem 1831
Belgium
Phone: +32 2 704 5622
EMail: bclaise@cisco.com
Quittek, et al. Informational [Page 28]