Diameter Priority Attribute-Value Pairs
RFC 6735

Document Type RFC - Proposed Standard (October 2012; No errata)
Authors Ken Carlberg  , Tom Taylor 
Last updated 2020-07-29
Replaces draft-carlberg-dime-priority-avps
Stream Internet Engineering Task Force (IETF)
Formats plain text html pdf htmlized (tools) htmlized bibtex
Stream WG state Submitted to IESG for Publication
Document shepherd Lionel Morand
IESG IESG state RFC 6735 (Proposed Standard)
Action Holders
Consensus Boilerplate Unknown
Telechat date
Responsible AD BenoƮt Claise
IESG note Lionel Morand (lionel.morand@orange-ftgroup.com) is the document shepherd
Send notices to (None)
Internet Engineering Task Force (IETF)                  K. Carlberg, Ed.
Request for Comments: 6735                                           G11
Category: Standards Track                                      T. Taylor
ISSN: 2070-1721                                     PT Taylor Consulting
                                                            October 2012

                Diameter Priority Attribute-Value Pairs


   This document defines Attribute-Value Pair (AVP) containers for
   various priority parameters for use with Diameter and the
   Authentication, Authorization, and Accounting (AAA) framework.  The
   parameters themselves are defined in several different protocols that
   operate at either the network or application layer.

Status of This Memo

   This is an Internet Standards Track document.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by
   the Internet Engineering Steering Group (IESG).  Further
   information on Internet Standards is available in Section 2 of
   RFC 5741.

   Information about the current status of this document, any
   errata, and how to provide feedback on it may be obtained at

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Carlberg & Taylor            Standards Track                    [Page 1]
RFC 6735                Resource Priorities AVPs            October 2012

   This document may contain material from IETF Documents or IETF
   Contributions published or made publicly available before November
   10, 2008.  The person(s) controlling the copyright in some of this
   material may not have granted the IETF Trust the right to allow
   modifications of such material outside the IETF Standards Process.
   Without obtaining an adequate license from the person(s) controlling
   the copyright in such materials, this document may not be modified
   outside the IETF Standards Process, and derivative works of it may
   not be created outside the IETF Standards Process, except to format
   it for publication as an RFC or to translate it into languages other
   than English.

1.  Introduction

   This document defines a number of Attribute-Value Pairs (AVP) that
   can be used within the Diameter protocol [RFC6733] to convey a
   specific set of priority parameters.  These parameters are specified
   in other documents, but are briefly described below.  The
   corresponding AVPs defined in Section 3 are extensions to those
   defined in [RFC5866].  We note that all the priority fields
   associated with the AVPs defined in this document are extensible and
   allow for additional values beyond what may have already been defined
   or registered with IANA.

   Priority influences the distribution of resources and, in turn, the
   QoS associated with that resource.  This influence may be
   probabilistic, ranging between (but not including) 0% and 100%, or it
   may be in the form of a guarantee to either receive or not receive
   the resource.

   Another example of how prioritization can be realized is articulated
   in Appendix A.3 (the Priority Bypass Model) of [RFC6401].  In this
   case, prioritized flows may gain access to resources that are never
   shared with non-prioritized flows.

1.1.  Other Priority-Related AVPs

   The 3rd Generation Partnership Project (3GPP) has defined several
   Diameter AVPs that support prioritization of sessions.  The following
   AVPs are intended to be used for priority services (e.g., Multimedia
   Priority Service):

      -  Reservation-Priority AVP as defined in [ETSI]
      -  MPS-Identifier AVP as defined in [3GPPa]
      -  Priority-Level AVP (as part of the Allocation Retention
         Priority AVP) as defined in [3GPPb]
      -  Session-Priority AVP as defined in [3GPPc] and [3GPPd]

Carlberg & Taylor            Standards Track                    [Page 2]
RFC 6735                Resource Priorities AVPs            October 2012

   Both the Reservation-Priority AVP and the Priority-Level AVP can
   carry priority levels associated with a session initiated by a user.
   We note that these AVPs are defined from the allotment set aside for
   3GPP for Diameter-based interfaces, and they are particularly aimed
Show full document text