RFC - Unknown
(April 1969; Errata)
||RFC Editor Note
RFC 2 (Unknown)
||Send notices to
Network Working Group Bill Duvall
Request for Comments: 2 SRI
[page 1 missing]
1a Control Links
1a1 Logical link 0 will be a control link between any two HOSTs on
1a1a Only one control link may exist between any two HOSTs on
the network. Thus, if there are n HOSTs on the network, there
are n-1 control links from each HOST.
1a2 It will be primarily used for communication between HOSTs for
the purposes of:
1a2a Establishing user links
1a2b Breaking user links
1a2c Passing interrupts regarding the status of links and/or
programs using the links
1a2d Monitor communication
1a3 Imps in the network may automatically trace all messages sent
on link 0.
1b Primary Links
1b1 A user at a given HOST may have exactly 1 primary link to each
of the other HOSTs on the network.
1b1a The primary link must be the first link established
between a HOST user and another HOST.
1b1b Primary links are global to a user, i.e. a user program
may open a primary link, and that link remains open until it is
Duvall [Page 1]
1b1c The primary link is treated like a teletype connected over
a normal data-phone or direct line by the remote HOST, i.e. the
remote HOST considers a primary link to be a normal teletype
1b1d The primary link is used for passing (user) control
information to the remote HOST, e.g. it will be used for
logging in to the remote host (using the remote hosts standard
1c Auxilliary Links
1c1 A user program may establish any number of auxilliary links
between itself and a user program in a connected HOST.
1c1a These links may be used for either binary or character
1c1b Auxilliary links are local to the sub-system which
establishes them, and therefore are closed when that subsystem
2 MANIPULATION OF LINKS
2a Control links
2a1 The control link is established at system load time.
2a2 The status of a control link may be active or inactive
2a2a The status of the control link should reflect the
relationship between the HOSTs.
2b Primary Links
2b1 Primary links are established by a user or executive call to
2b1a The network identification number of the HOST to be linked
to must be included in the call
2b1b An attempt to establish more than one primary link to a
particular HOST will be regarded as an error, and the request
will be defaulted
2b1c Standard Transmission Character Set
Duvall [Page 2]
2b1c1 There will be a standard character set for
transmission of data over the primary links and control
2b1c1a This will be full (8 bit) ASCII.
2b1d (get link) The protocol for establishing a link to HOST B
from HOST A is as follows
2b1d1 A selects a currently unused link to HOST B from its
2b1d2 A transmits a link-connect message to B over link 0.
2b1d3 A then waits for:
2b1d3a A communication regarding that link from B
2b1d3b A certain amount of time to elaspse
2b1d4 If a communication regarding the link is received from
B, it is examined to see if it is:
2b1d4a A verification of the link from B.
2b1d4a1 This results in a successful return from the
monitor to the requestor. The link number is returned
to the requestor, and the link is established.
2b1d4b A request from B to establish the link. This
means: that B is trying to establish the same link as A
independently of A.
2b1d4b1 If the network ID number of A(Na) is greater
than that of B(Nb), then A ignores the request, and
continues to await confirmation of the link from B.
2b1d4b2 If, on the other hand, Na<Nb, A:
2b1d4b2a Honors the request from B to establish the
2b1d4b2b Sends verification as required,
2b1d4b2c Aborts its own request, and repeats the
Duvall [Page 3]
2b1d4c Some other communication from B regarding the
2b1d4c1 This is an error condition, meaning that
2b1d4c1a A has faulted by selecting a previously
allocated link for allocation,
2b1d4c1b B is transmitting information over an un-
2b1d4c1c Or a message regarding allocation from B
to A has been garbled in transmission.
2b1d4c2 In this case, A's action is to:
2b1d4c2a Send a link disconnect message to B
concerning the attempted connection
2b1d4c2b Consider the state of HOST B to be in
error and initiate entry to a panic routine(error).
2b1d5 If no communication regarding the link is received
from B in the prescribed amount of time, HOST B is
considered to be in an error state.
2b1d5a A link disconnect message is sent to B from A.
2b1d5b A panic routine is called(error).
2c Auxilliary Links
2c1 Auxilliary links are established by a call to the monitor from
a user program.
2c1a The request must specify pertinent data about the desired
link to the monitor
2c1a1 The number of the primary link to B.
2c1b The request for an auxilliary link must be made by a user
program in each of the HOSTs (A and B).
2c1c If Na > Nb, then HOST A proceeds to establish a link to
HOST B in the manner outlined above (getlink).
Duvall [Page 4]
2c1d If Na<Nb, then A waits:
2c1d1 For HOST B to establish the link (after looking to see
if B has already established the corresponding link).
2c1d2 For a specified amount of time to elapse.
2c1d2a This means that HOST B did not respond to the
request of HOST A.
2c1d2b The program in HOST A and B should be able to
specifiy the amount of time to wait for the timeout.
3 ERROR CHECKING
3a All messages sent over the network will be error checked initally
so as to help isolate software and hardware bugs.
3b A checksum will be associated with each message, which is order
3b1 The following algorithm is one which might be used:
3b1a A checksum of length 1 may be formed by adding successive
fields in the string to be checked serially, and adding the
carry bit into the lowest bit position of the sum.
| | |
ADD CARRY---> | |
3b1a1 This process is known as folding.
Duvall [Page 5]
3b1a2 Several fields may be added and folded in parallel, if
they are folded appropiately after the addition.
| FIELD 4 | FIELD 3 | FIELD 2 | FIELD 1 |
| FIELD 8 | FIELD 7 | FIELD 6 | FIELD 5 |
| | | | | |
| | | | |
| | | | v
| | | | +---------+
| | | | | |
| | | | +---------+
| | | |
| | | \ +---------+
| | | `-> | |
| | | +---------+
| | |
| | \ +---------+
| | `-----------> | |
| | +---------+
| \ +---------+
| `--------------------->| |
| | |
ADD `-----> | |
Duvall [Page 6]
3b1a2a Using this scheme, it is assumed that, if there
are n fields, the carries from the first n-1 fields
are automatically added into the low order position of
the next higher field, so that in folding, one need
only add the [n] result fields to the carry from the
nth field, and then add in an appropiately sized carry
from that addition (and repeat the desired number of
times to achieve the result.
3b1a3 A checksum computed in this manner has the advantage
that the word lengths of different machines may each be used
3b1a3a If a string of suitable length is chosen for
computing the checksum, and a suitable checksum field
length is selected, the checksum technique for each of
the machines will be relatively optimal.
3b1a3a1 Field length: 288 bits (lowest common
denomenator of (24,32,36)
3b1a3a2 Checksum length: 8 bits (convenient field size
for all machines)
3b1b If a message is divided into groups of fields, and each
group is checksummed in this manner, an order dependent
checksum may be got by shifting the checksum for each group,
and adding it in (successively) to the checksum of the next
3c A facility will be provided where two HOSTs may enter a mode which
requires positive verification of all messages. This verification is
sent over the control link.
4 MONITOR FUNCTIONS
4a Network I/O drivers
4a1a Input message from IMP.
4a1b Do error checking on message.
4a1b1 Verify checksum,
4a1b2 Send "message recieved" aknowledgement over control
link if aknowledge mode is in effect.
Duvall [Page 7]
4a1c (trans)character translation
4a1c1 There is a strong possibility that the character
translation may be done in the IMP.
4a1c2 This needs to be explored further with BBN.
4a1c3 There are two main considerations
4a1c3a Should the translation be done by table or
4a1c3a1 Initially it seems as though the best way to
go is table.
4a1c3b How should we decide which messages should be
translated, i.e. is it desirable to not translate
everything (YES!!) and by what means can we use to
4a1d Decode header, and pass message to correct recipient as
identified by source, and link.
4a2a Build header
4a2b Character translation
4a2b1 See remarks under the section on output translation
4a2c Create checksum
4a2d Check status of link
4a2d1 If there has not been a RFNM since the last message
transmitted out the link, wait for it.
4a2e Transmit message to IMP
4a2f If aknowledge mode is in effect,wait for
4a2f1 RFNM from destination IMP.
4a2f2 Response from destination HOST over control line 0.
Duvall [Page 8]
4b Network status
4b1 Maintain status of other HOSTs on network
4b1a If an IMP is down, then his HOST is considered to be down.
4b2 Maintain status of control lines.
4b3 Answer status queries from other HOSTs.
4b4 Inform other HOSTs as to status of primary and auxilliary
links on an interrupt basis.
4b5 Inform other HOSTs as to status of programs using primary and
5 EXECUTIVE PRIMITIVES
5a Primary Links
5a1 These require the HOST number as a parameter.
5a1a Establish primary link
5a1b Connect controlling teletype to primary link
5a1c INPUT/OUTPUT over primary link
5a1d Interrogate status of primary link
5a1d1 Don't know what, exactly, this should do, but it seems
as though it might be useful.
5a1e Disconnect controlling teletype from primary link
5a1f Kill primary link
5b Auxilliary Links.
5b1 Establish auxilliary link.
5b1a requires the HOST number as a parameter
5b1b It returns a logical link number which is similar to a
file index. It is this number which is passed to all of the
other Auxilliary routines as a parameter.
5b2 INPUT/OUTPUT over auxilliary link
Duvall [Page 9]
5b3 Interrogate status auxilliary link.
5b3a Don't know what, exactly, this should do, but it seems as
though it might be useful.
5b4 Kill auxilliary link.
5c Special executive functions
5c1 Transparent. INPUT/OUTPUT over link
5c1a This may be used to do block I/O transfers over a link
5c1b The function of the monitor in this instance is to
transfer a buffer directly to its IMP
5c1c At does not modify it in any way
5c1c1 This means that the header and other control
information must be in the buffer.
5c1d The indended use of this is for network debugging.
6 INITIAL CHECKOUT
6a The network will be initially checked out using the links in a
simulated data-phone mode.
6a1 All messages will be one character in length.
6a2 Links will be transparent to the monitor, and controlled by
user program via a special executive primitive.
6a2a The initial test will be run from two user programs in
different HOSTs, e.g. DDT to DDT.
6a2b It will be paralleled by a telephone link or similar.
[ This RFC was put into machine readable form for entry ]
[ into the online RFC archives by Robbie Bennet 10/1998 ]
[ This RFC was nroffed by Kelly Tardif, Viagenie 10/1999 ]
Duvall [Page 10]