Skip to main content

Transport Mappings for Version 2 of the Simple Network Management Protocol (SNMPv2)
RFC 1906

Document Type RFC - Draft Standard (January 1996)
Obsoleted by RFC 3417
Obsoletes RFC 1449
Authors Dr. Jeff D. Case , Keith McCloghrie, Dr. Marshall T. Rose , Steven Waldbusser
Last updated 2013-03-02
RFC stream Internet Engineering Task Force (IETF)
Formats
Additional resources Mailing list discussion
IESG Responsible AD (None)
Send notices to (None)
RFC 1906
Network Working Group                               SNMPv2 Working Group
Request for Comments: 1906                                       J. Case
Obsoletes: 1449                                      SNMP Research, Inc.
Category: Standards Track                                  K. McCloghrie
                                                     Cisco Systems, Inc.
                                                                 M. Rose
                                            Dover Beach Consulting, Inc.
                                                           S. Waldbusser
                                          International Network Services
                                                            January 1996

                Transport Mappings for Version 2 of the
              Simple Network Management Protocol (SNMPv2)

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Table of Contents

   1. Introduction ................................................    2
   1.1 A Note on Terminology ......................................    2
   2. Definitions .................................................    3
   3. SNMPv2 over UDP .............................................    5
   3.1 Serialization ..............................................    5
   3.2 Well-known Values ..........................................    5
   4. SNMPv2 over OSI .............................................    6
   4.1 Serialization ..............................................    6
   4.2 Well-known Values ..........................................    6
   5. SNMPv2 over DDP .............................................    6
   5.1 Serialization ..............................................    6
   5.2 Well-known Values ..........................................    6
   5.3 Discussion of AppleTalk Addressing .........................    7
   5.3.1 How to Acquire NBP names .................................    8
   5.3.2 When to Turn NBP names into DDP addresses ................    8
   5.3.3 How to Turn NBP names into DDP addresses .................    8
   5.3.4 What if NBP is broken ....................................    9
   6. SNMPv2 over IPX .............................................    9
   6.1 Serialization ..............................................    9
   6.2 Well-known Values ..........................................    9
   7. Proxy to SNMPv1 .............................................   10
   8. Serialization using the Basic Encoding Rules ................   10
   8.1 Usage Example ..............................................   11

SNMPv2 Working Group        Standards Track                     [Page 1]
RFC 1906             Transport Mappings for SNMPv2          January 1996

   9. Security Considerations .....................................   11
   10. Editor's Address ...........................................   12
   11. Acknowledgements ...........................................   12
   12. References .................................................   13

1.  Introduction

   A management system contains:  several (potentially many) nodes, each
   with a processing entity, termed an agent, which has access to
   management instrumentation; at least one management station; and, a
   management protocol, used to convey management information between
   the agents and management stations.  Operations of the protocol are
   carried out under an administrative framework which defines
   authentication, authorization, access control, and privacy policies.

   Management stations execute management applications which monitor and
   control managed elements.  Managed elements are devices such as
   hosts, routers, terminal servers, etc., which are monitored and
   controlled via access to their management information.

   The management protocol, version 2 of the Simple Network Management
   Protocol [1], may be used over a variety of protocol suites.  It is
   the purpose of this document to define how the SNMPv2 maps onto an
   initial set of transport domains.  Other mappings may be defined in
   the future.

   Although several mappings are defined, the mapping onto UDP is the
   preferred mapping.  As such, to provide for the greatest level of
   interoperability, systems which choose to deploy other mappings
   should also provide for proxy service to the UDP mapping.

1.1.  A Note on Terminology

   For the purpose of exposition, the original Internet-standard Network
   Management Framework, as described in RFCs 1155 (STD 16), 1157 (STD
   15), and 1212 (STD 16), is termed the SNMP version 1 framework
   (SNMPv1).  The current framework is termed the SNMP version 2
   framework (SNMPv2).

SNMPv2 Working Group        Standards Track                     [Page 2]
RFC 1906             Transport Mappings for SNMPv2          January 1996

2.  Definitions

SNMPv2-TM DEFINITIONS ::= BEGIN

IMPORTS
    OBJECT-IDENTITY, snmpDomains, snmpProxys
        FROM SNMPv2-SMI
    TEXTUAL-CONVENTION
        FROM SNMPv2-TC;

-- SNMPv2 over UDP over IPv4

snmpUDPDomain  OBJECT-IDENTITY
    STATUS     current
    DESCRIPTION
            "The SNMPv2 over UDP transport domain.  The corresponding
            transport address is of type SnmpUDPAddress."
    ::= { snmpDomains 1 }

SnmpUDPAddress ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "1d.1d.1d.1d/2d"
    STATUS       current
    DESCRIPTION
            "Represents a UDP address:

               octets   contents        encoding
                1-4     IP-address      network-byte order
                5-6     UDP-port        network-byte order
            "
    SYNTAX       OCTET STRING (SIZE (6))

-- SNMPv2 over OSI

snmpCLNSDomain OBJECT-IDENTITY
    STATUS     current
    DESCRIPTION
            "The SNMPv2 over CLNS transport domain.  The corresponding
            transport address is of type SnmpOSIAddress."
    ::= { snmpDomains 2 }

snmpCONSDomain OBJECT-IDENTITY
    STATUS     current
    DESCRIPTION
            "The SNMPv2 over CONS transport domain.  The corresponding
            transport address is of type SnmpOSIAddress."
    ::= { snmpDomains 3 }

SNMPv2 Working Group        Standards Track                     [Page 3]
RFC 1906             Transport Mappings for SNMPv2          January 1996

SnmpOSIAddress ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "*1x:/1x:"
    STATUS       current
    DESCRIPTION
            "Represents an OSI transport-address:

               octets   contents           encoding
                  1     length of NSAP     'n' as an unsigned-integer
                                              (either 0 or from 3 to 20)
               2..(n+1) NSAP                concrete binary representation
               (n+2)..m TSEL                string of (up to 64) octets
            "
    SYNTAX       OCTET STRING (SIZE (1 | 4..85))

-- SNMPv2 over DDP

snmpDDPDomain  OBJECT-IDENTITY
    STATUS     current
    DESCRIPTION
            "The SNMPv2 over DDP transport domain.  The corresponding
            transport address is of type SnmpNBPAddress."
    ::= { snmpDomains 4 }

SnmpNBPAddress ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
            "Represents an NBP name:

                 octets        contents          encoding
                    1          length of object  'n' as an unsigned integer
                  2..(n+1)     object            string of (up to 32) octets
                   n+2         length of type    'p' as an unsigned integer
              (n+3)..(n+2+p)   type              string of (up to 32) octets
                  n+3+p        length of zone    'q' as an unsigned integer
            (n+4+p)..(n+3+p+q) zone              string of (up to 32) octets

            For comparison purposes, strings are case-insensitive All
            strings may contain any octet other than 255 (hex ff)."
    SYNTAX       OCTET STRING (SIZE (3..99))

-- SNMPv2 over IPX

snmpIPXDomain  OBJECT-IDENTITY
    STATUS     current
    DESCRIPTION
            "The SNMPv2 over IPX transport domain.  The corresponding

SNMPv2 Working Group        Standards Track                     [Page 4]
RFC 1906             Transport Mappings for SNMPv2          January 1996

            transport address is of type SnmpIPXAddress."
    ::= { snmpDomains 5 }

SnmpIPXAddress ::= TEXTUAL-CONVENTION
    DISPLAY-HINT "4x.1x:1x:1x:1x:1x:1x.2d"
    STATUS       current
    DESCRIPTION
            "Represents an IPX address:

               octets   contents            encoding
                1-4     network-number      network-byte order
                5-10    physical-address    network-byte order
               11-12    socket-number       network-byte order
            "
    SYNTAX       OCTET STRING (SIZE (12))

-- for proxy to SNMPv1 (RFC 1157)

rfc1157Proxy   OBJECT IDENTIFIER ::= { snmpProxys 1 }

rfc1157Domain  OBJECT-IDENTITY
    STATUS     current
    DESCRIPTION
            "The transport domain for SNMPv1 over UDP.  The
            corresponding transport address is of type SnmpUDPAddress."
    ::= { rfc1157Proxy 1 }

--  ::= { rfc1157Proxy 2 }            this OID is obsolete

END

3.  SNMPv2 over UDP

   This is the preferred transport mapping.

3.1.  Serialization

   Each instance of a message is serialized (i.e., encoded according to
   the convention of [1]) onto a single UDP[2] datagram, using the
   algorithm specified in Section 8.

3.2.  Well-known Values

   It is suggested that administrators configure their SNMPv2 entities
   acting in an agent role to listen on UDP port 161.  Further, it is
   suggested that notification sinks be configured to listen on UDP port

SNMPv2 Working Group        Standards Track                     [Page 5]
RFC 1906             Transport Mappings for SNMPv2          January 1996

   162.

   When an SNMPv2 entity uses this transport mapping, it must be capable
   of accepting messages that are at least 484 octets in size.
   Implementation of larger values is encouraged whenever possible.

4.  SNMPv2 over OSI

   This is an optional transport mapping.

4.1.  Serialization

   Each instance of a message is serialized onto a single TSDU [3,4] for
   the OSI Connectionless-mode Transport Service (CLTS), using the
   algorithm specified in Section 8.

4.2.  Well-known Values

   It is suggested that administrators configure their SNMPv2 entities
   acting in an agent role to listen on transport selector "snmp-l"
   (which consists of six ASCII characters), when using a CL-mode
   network service to realize the CLTS.  Further, it is suggested that
   notification sinks be configured to listen on transport selector
   "snmpt-l" (which consists of seven ASCII characters, six letters and
   a hyphen) when using a CL-mode network service to realize the CLTS.
   Similarly, when using a CO-mode network service to realize the CLTS,
   the suggested transport selectors are "snmp-o" and "snmpt-o", for
   agent and notification sink, respectively.

   When an SNMPv2 entity uses this transport mapping, it must be capable
   of accepting messages that are at least 484 octets in size.
   Implementation of larger values is encouraged whenever possible.

5.  SNMPv2 over DDP

   This is an optional transport mapping.

5.1.  Serialization

   Each instance of a message is serialized onto a single DDP datagram
   [5], using the algorithm specified in Section 8.

5.2.  Well-known Values

   SNMPv2 messages are sent using DDP protocol type 8.  SNMPv2 entities
   acting in an agent role listens on DDP socket number 8, whilst
   notification sinks listen on DDP socket number 9.

SNMPv2 Working Group        Standards Track                     [Page 6]
RFC 1906             Transport Mappings for SNMPv2          January 1996

   Administrators must configure their SNMPv2 entities acting in an
   agent role to use NBP type "SNMP Agent" (which consists of ten ASCII
   characters), whilst notification sinks must be configured to use NBP
   type "SNMP Trap Handler" (which consists of seventeen ASCII
   characters).

   The NBP name for agents and notification sinks should be stable - NBP
   names should not change any more often than the IP address of a
   typical TCP/IP node.  It is suggested that the NBP name be stored in
   some form of stable storage.

   When an SNMPv2 entity uses this transport mapping, it must be capable
   of accepting messages that are at least 484 octets in size.
   Implementation of larger values is encouraged whenever possible.

5.3.  Discussion of AppleTalk Addressing

   The AppleTalk protocol suite has certain features not manifest in the
   TCP/IP suite.  AppleTalk's naming strategy and the dynamic nature of
   address assignment can cause problems for SNMPv2 entities that wish
   to manage AppleTalk networks.  TCP/IP nodes have an associated IP
   address which distinguishes each from the other.  In contrast,
   AppleTalk nodes generally have no such characteristic.  The network-
   level address, while often relatively stable, can change at every
   reboot (or more frequently).

   Thus, when SNMPv2 is mapped over DDP, nodes are identified by a
   "name", rather than by an "address".  Hence, all AppleTalk nodes that
   implement this mapping are required to respond to NBP lookups and
   confirms (e.g., implement the NBP protocol stub), which guarantees
   that a mapping from NBP name to DDP address will be possible.

   In determining the SNMP identity to register for an SNMPv2 entity, it
   is suggested that the SNMP identity be a name which is associated
   with other network services offered by the machine.

   NBP lookups, which are used to map NBP names into DDP addresses, can
   cause large amounts of network traffic as well as consume CPU
   resources.  It is also the case that the ability to perform an NBP
   lookup is sensitive to certain network disruptions (such as zone
   table inconsistencies) which would not prevent direct AppleTalk
   communications between two SNMPv2 entities.

   Thus, it is recommended that NBP lookups be used infrequently,
   primarily to create a cache of name-to-address mappings.  These
   cached mappings should then be used for any further SNMP traffic.  It
   is recommended that SNMPv2 entities acting in a manager role should
   maintain this cache between reboots.  This caching can help minimize

SNMPv2 Working Group        Standards Track                     [Page 7]
RFC 1906             Transport Mappings for SNMPv2          January 1996

   network traffic, reduce CPU load on the network, and allow for (some
   amount of) network trouble shooting when the basic name-to-address
   translation mechanism is broken.

5.3.1.  How to Acquire NBP names

   An SNMPv2 entity acting in a manager role may have a pre-configured
   list of names of "known" SNMPv2 entities acting in an agent role.
   Similarly, an SNMPv2 entity acting in a manager role might interact
   with an operator.  Finally, an SNMPv2 entity acting in a manager role
   might communicate with all SNMPv2 entities acting in an agent role in
   a set of zones or networks.

5.3.2.  When to Turn NBP names into DDP addresses

   When an SNMPv2 entity uses a cache entry to address an SNMP packet,
   it should attempt to confirm the validity mapping, if the mapping
   hasn't been confirmed within the last T1 seconds.  This cache entry
   lifetime, T1, has a minimum, default value of 60 seconds, and should
   be configurable.

   An SNMPv2 entity acting in a manager role may decide to prime its
   cache of names prior to actually communicating with another SNMPv2
   entity.  In general, it is expected that such an entity may want to
   keep certain mappings "more current" than other mappings, e.g., those
   nodes which represent the network infrastructure (e.g., routers) may
   be deemed "more important".

   Note that an SNMPv2 entity acting in a manager role should not prime
   its entire cache upon initialization - rather, it should attempt
   resolutions over an extended period of time (perhaps in some pre-
   determined or configured priority order).  Each of these resolutions
   might, in fact, be a wildcard lookup in a given zone.

   An SNMPv2 entity acting in an agent role must never prime its cache.
   Such an entity should do NBP lookups (or confirms) only when it needs
   to send an SNMP trap.  When generating a response, such an entity
   does not need to confirm a cache entry.

5.3.3.  How to Turn NBP names into DDP addresses

   If the only piece of information available is the NBP name, then an
   NBP lookup should be performed to turn that name into a DDP address.
   However, if there is a piece of stale information, it can be used as
   a hint to perform an NBP confirm (which sends a unicast to the
   network address which is presumed to be the target of the name
   lookup) to see if the stale information is, in fact, still valid.

SNMPv2 Working Group        Standards Track                     [Page 8]
RFC 1906             Transport Mappings for SNMPv2          January 1996

   An NBP name to DDP address mapping can also be confirmed implicitly
   using only SNMP transactions.  For example, an SNMPv2 entity acting
   in a manager role issuing a retrieval operation could also retrieve
   the relevant objects from the NBP group [6] for the SNMPv2 entity
   acting in an agent role.  This information can then be correlated
   with the source DDP address of the response.

5.3.4.  What if NBP is broken

   Under some circumstances, there may be connectivity between two
   SNMPv2 entities, but the NBP mapping machinery may be broken, e.g.,

o    the NBP FwdReq (forward NBP lookup onto local attached network)
     mechanism might be broken at a router on the other entity's
     network; or,

o    the NBP BrRq (NBP broadcast request) mechanism might be broken
     at a router on the entity's own network; or,

o    NBP might be broken on the other entity's node.

   An SNMPv2 entity acting in a manager role which is dedicated to
   AppleTalk management might choose to alleviate some of these failures
   by directly implementing the router portion of NBP.  For example,
   such an entity might already know all the zones on the AppleTalk
   internet and the networks on which each zone appears.  Given an NBP
   lookup which fails, the entity could send an NBP FwdReq to the
   network in which the agent was last located.  If that failed, the
   station could then send an NBP LkUp (NBP lookup packet) as a directed
   (DDP) multicast to each network number on that network.  Of the above
   (single) failures, this combined approach will solve the case where
   either the local router's BrRq-to-FwdReq mechanism is broken or the
   remote router's FwdReq-to-LkUp mechanism is broken.

6.  SNMPv2 over IPX

   This is an optional transport mapping.

6.1.  Serialization

   Each instance of a message is serialized onto a single IPX datagram
   [7], using the algorithm specified in Section 8.

6.2.  Well-known Values

   SNMPv2 messages are sent using IPX packet type 4 (i.e., Packet
   Exchange Protocol).

SNMPv2 Working Group        Standards Track                     [Page 9]
RFC 1906             Transport Mappings for SNMPv2          January 1996

   It is suggested that administrators configure their SNMPv2 entities
   acting in an agent role to listen on IPX socket 36879 (900f
   hexadecimal).  Further, it is suggested that notification sinks be
   configured to listen on IPX socket 36880 (9010 hexadecimal)

   When an SNMPv2 entity uses this transport mapping, it must be capable
   of accepting messages that are at least 546 octets in size.
   Implementation of larger values is encouraged whenever possible.

7.  Proxy to SNMPv1

   In order to provide proxy to SNMPv1 [8], it may be useful to define a
   transport domain, rfc1157Domain, which indicates the transport
   mapping for SNMP messages as defined in RFC 1157.  Section 3.1 of [9]
   specifies the behavior of the proxy agent.

8.  Serialization using the Basic Encoding Rules

   When the Basic Encoding Rules [10] are used for serialization:

   (1)  When encoding the length field, only the definite form is used; use
        of the indefinite form encoding is prohibited.  Note that when
        using the definite-long form, it is permissible to use more than
        the minimum number of length octets necessary to encode the length
        field.

   (2)  When encoding the value field, the primitive form shall be used for
        all simple types, i.e., INTEGER, OCTET STRING, and OBJECT
        IDENTIFIER (either IMPLICIT or explicit).  The constructed form of
        encoding shall be used only for structured types, i.e., a SEQUENCE
        or an IMPLICIT SEQUENCE.

   (3)  When encoding an object whose syntax is described using the BITS
        construct, the value is encoded as an OCTET STRING, in which all
        the named bits in (the definition of) the bitstring, commencing
        with the first bit and proceeding to the last bit, are placed in
        bits 8 to 1 of the first octet, followed by bits 8 to 1 of each
        subsequent octet in turn, followed by as many bits as are needed of
        the final subsequent octet, commencing with bit 8.  Remaining bits,
        if any, of the final octet are set to zero on generation and
        ignored on receipt.

   These restrictions apply to all aspects of ASN.1 encoding, including
   the message wrappers, protocol data units, and the data objects they
   contain.

SNMPv2 Working Group        Standards Track                    [Page 10]
RFC 1906             Transport Mappings for SNMPv2          January 1996

8.1.  Usage Example

   As an example of applying the Basic Encoding Rules, suppose one
   wanted to encode an instance of the GetBulkRequest-PDU [1]:

     [5] IMPLICIT SEQUENCE {
             request-id      1414684022,
             non-repeaters   1,
             max-repetitions 2,
             variable-bindings {
                 { name sysUpTime,
                   value { unspecified NULL } },
                 { name ipNetToMediaPhysAddress,
                   value { unspecified NULL } },
                 { name ipNetToMediaType,
                   value { unspecified NULL } }
             }
         }

Applying the BER, this would be encoded (in hexadecimal) as:

[5] IMPLICIT SEQUENCE          a5 82 00 39
    INTEGER                    02 04 52 54 5d 76
    INTEGER                    02 01 01
    INTEGER                    02 01 02
    SEQUENCE                   30 2b
        SEQUENCE               30 0b
            OBJECT IDENTIFIER  06 07 2b 06 01 02 01 01 03
            NULL               05 00
        SEQUENCE               30 0d
            OBJECT IDENTIFIER  06 09 2b 06 01 02 01 04 16 01 02
            NULL               05 00
        SEQUENCE               30 0d
            OBJECT IDENTIFIER  06 09 2b 06 01 02 01 04 16 01 04
            NULL               05 00

   Note that the initial SEQUENCE is not encoded using the minimum
   number of length octets.  (The first octet of the length, 82,
   indicates that the length of the content is encoded in the next two
   octets.)

9.  Security Considerations

   Security issues are not discussed in this memo.

SNMPv2 Working Group        Standards Track                    [Page 11]
RFC 1906             Transport Mappings for SNMPv2          January 1996

10.  Editor's Address

   Keith McCloghrie
   Cisco Systems, Inc.
   170 West Tasman Drive
   San Jose, CA  95134-1706
   US

   Phone: +1 408 526 5260
   EMail: kzm@cisco.com

11.  Acknowledgements

   This document is the result of significant work by the four major
   contributors:

   Jeffrey D. Case (SNMP Research, case@snmp.com)
   Keith McCloghrie (Cisco Systems, kzm@cisco.com)
   Marshall T. Rose (Dover Beach Consulting, mrose@dbc.mtview.ca.us)
   Steven Waldbusser (International Network Services, stevew@uni.ins.com)

   In addition, the contributions of the SNMPv2 Working Group are
   acknowledged.  In particular, a special thanks is extended for the
   contributions of:

     Alexander I. Alten (Novell)
     Dave Arneson (Cabletron)
     Uri Blumenthal (IBM)
     Doug Book (Chipcom)
     Kim Curran (Bell-Northern Research)
     Jim Galvin (Trusted Information Systems)
     Maria Greene (Ascom Timeplex)
     Iain Hanson (Digital)
     Dave Harrington (Cabletron)
     Nguyen Hien (IBM)
     Jeff Johnson (Cisco Systems)
     Michael Kornegay (Object Quest)
     Deirdre Kostick (AT&T Bell Labs)
     David Levi (SNMP Research)
     Daniel Mahoney (Cabletron)
     Bob Natale (ACE*COMM)
     Brian O'Keefe (Hewlett Packard)
     Andrew Pearson (SNMP Research)
     Dave Perkins (Peer Networks)
     Randy Presuhn (Peer Networks)
     Aleksey Romanov (Quality Quorum)
     Shawn Routhier (Epilogue)
     Jon Saperia (BGS Systems)

SNMPv2 Working Group        Standards Track                    [Page 12]
RFC 1906             Transport Mappings for SNMPv2          January 1996

     Bob Stewart (Cisco Systems, bstewart@cisco.com), chair
     Kaj Tesink (Bellcore)
     Glenn Waters (Bell-Northern Research)
     Bert Wijnen (IBM)

12.  References

[1]  SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and
     S. Waldbusser, "Protocol Operations for Version 2 of the Simple
     Network Management Protocol (SNMPv2)", RFC 1905, January 1996.

[2]  Postel, J., "User Datagram Protocol", STD 6, RFC 768,
     USC/Information Sciences Institute, August 1980.

[3]  Information processing systems - Open Systems Interconnection -
     Transport Service Definition, International Organization for
     Standardization.  International Standard 8072, (June, 1986).

[4]  Information processing systems - Open Systems Interconnection -
     Transport Service Definition - Addendum 1: Connectionless-mode
     Transmission, International Organization for Standardization.
     International Standard 8072/AD 1, (December, 1986).

[5]  G. Sidhu, R. Andrews, A. Oppenheimer, Inside AppleTalk (second
     edition).  Addison-Wesley, 1990.

[6]  Waldbusser, S., "AppleTalk Management Information Base", RFC 1243,
     Carnegie Mellon University, July 1991.

[7]  Network System Technical Interface Overview.  Novell, Inc, (June,
     1989).

[8]  Case, J., Fedor, M., Schoffstall, M., and J. Davin, "Simple Network
     Management Protocol", STD 15, RFC 1157, SNMP Research, Performance
     Systems International, MIT Laboratory for Computer Science, May
     1990.

[9]  SNMPv2 Working Group, Case, J., McCloghrie, K., Rose, M., and
     S. Waldbusser, "Coexistence between Version 1 and Version 2 of the
     Internet-standard Network Management Framework", RFC 1908,
     January 1996.

[10] Information processing systems - Open Systems Interconnection -
     Specification of Basic Encoding Rules for Abstract Syntax Notation
     One (ASN.1), International Organization for Standardization.
     International Standard 8825, December 1987.

SNMPv2 Working Group        Standards Track                    [Page 13]