POP3 AUTHentication command
RFC 1734

Document Type RFC - Proposed Standard (December 1994; No errata)
Obsoleted by RFC 5034
Was draft-myers-pop3-auth (individual)
Last updated 2013-03-02
Stream Legacy
Formats plain text html pdf htmlized bibtex
Stream Legacy state (None)
Consensus Boilerplate Unknown
RFC Editor Note (None)
IESG IESG state RFC 1734 (Proposed Standard)
Telechat date
Responsible AD (None)
Send notices to (None)
Network Working Group                                           J. Myers
Request for Comments: 1734                               Carnegie Mellon
Category: Standards Track                                  December 1994

                      POP3 AUTHentication command

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

1. Introduction

   This document describes the optional AUTH command, for indicating an
   authentication mechanism to the server, performing an authentication
   protocol exchange, and optionally negotiating a protection mechanism
   for subsequent protocol interactions.  The authentication and
   protection mechanisms used by the POP3 AUTH command are those used by

2. The AUTH command

   AUTH mechanism

             a string identifying an IMAP4 authentication mechanism,
             such as defined by [IMAP4-AUTH].  Any use of the string
             "imap" used in a server authentication identity in the
             definition of an authentication mechanism is replaced with
             the string "pop".

             may only be given in the AUTHORIZATION state

             The AUTH command indicates an authentication mechanism to
             the server.  If the server supports the requested
             authentication mechanism, it performs an authentication
             protocol exchange to authenticate and identify the user.
             Optionally, it also negotiates a protection mechanism for
             subsequent protocol interactions.  If the requested
             authentication mechanism is not supported, the server

Myers                                                           [Page 1]
RFC 1734                       POP3 AUTH                   December 1994

             should reject the AUTH command by sending a negative

             The authentication protocol exchange consists of a series
             of server challenges and client answers that are specific
             to the authentication mechanism.  A server challenge,
             otherwise known as a ready response, is a line consisting
             of a "+" character followed by a single space and a BASE64
             encoded string.  The client answer consists of a line
             containing a BASE64 encoded string.  If the client wishes
             to cancel an authentication exchange, it should issue a
             line with a single "*".  If the server receives such an
             answer, it must reject the AUTH command by sending a
             negative response.

             A protection mechanism provides integrity and privacy
             protection to the protocol session.  If a protection
             mechanism is negotiated, it is applied to all subsequent
             data sent over the connection.  The protection mechanism
             takes effect immediately following the CRLF that concludes
             the authentication exchange for the client, and the CRLF of
             the positive response for the server.  Once the protection
             mechanism is in effect, the stream of command and response
             octets is processed into buffers of ciphertext.  Each
             buffer is transferred over the connection as a stream of
             octets prepended with a four octet field in network byte
             order that represents the length of the following data.
             The maximum ciphertext buffer length is defined by the
             protection mechanism.

             The server is not required to support any particular
             authentication mechanism, nor are authentication mechanisms
             required to support any protection mechanisms.  If an AUTH
             command fails with a negative response, the session remains
             in the AUTHORIZATION state and client may try another
             authentication mechanism by issuing another AUTH command,
             or may attempt to authenticate by using the USER/PASS or
             APOP commands.  In other words, the client may request
             authentication types in decreasing order of preference,
             with the USER/PASS or APOP command as a last resort.

             Should the client successfully complete the authentication
             exchange, the POP3 server issues a positive response and
             the POP3 session enters the TRANSACTION state.

         Possible Responses:
             +OK maildrop locked and ready
             -ERR authentication exchange failed

Myers                                                           [Page 2]
RFC 1734                       POP3 AUTH                   December 1994
Show full document text