Network Working Group B. Sarikaya
Internet-Draft Huawei USA
Intended status: Standards Track February 20, 2015
Expires: August 24, 2015
Source Address Dependent Routing and Source Address Selection for IPv6
Hosts
draft-sarikaya-6man-sadr-overview-05
Abstract
This document presents the source address dependent routing from the
host perspective. Multihomed hosts and hosts with multiple
interfaces are considered. Different architectures are introduced
and with their help, why source address selection and next hop
resolution in view of source address dependent routing is needed is
explained. The document concludes with an informative guidelines on
the different solution approaches.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 24, 2015.
Copyright Notice
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Sarikaya Expires August 24, 2015 [Page 1]
Internet-Draft SADR February 2015
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. SADR Scenarios . . . . . . . . . . . . . . . . . . . . . . . 4
4. Analysis of Source Address Dependent Routing . . . . . . . . 7
4.1. Scenarios Analysis . . . . . . . . . . . . . . . . . . . 7
4.2. Provisioning Domains and SADR . . . . . . . . . . . . . . 9
5. Guidelines on Standardization Work . . . . . . . . . . . . . 9
5.1. Source Address Selection Rule 5.5 . . . . . . . . . . . . 10
5.2. Router Advertisement Option . . . . . . . . . . . . . . . 10
5.3. Router Advertisement Option Set . . . . . . . . . . . . . 11
5.4. Other Solutions . . . . . . . . . . . . . . . . . . . . . 12
6. Security Considerations . . . . . . . . . . . . . . . . . . . 12
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 13
9. References . . . . . . . . . . . . . . . . . . . . . . . . . 13
9.1. Normative References . . . . . . . . . . . . . . . . . . 13
9.2. Informative References . . . . . . . . . . . . . . . . . 14
Author's Address . . . . . . . . . . . . . . . . . . . . . . . . 16
1. Introduction
BCP 38 recommends ingress traffic routing to prohibit Denial of
Service (DoS) attacks, i.e. datagrams which have source addresses
that do not match with the network where the host is attached are
discarded [RFC2827]. Avoiding packets to be dropped because of
ingress filtering is difficult especially in multihomed networks
where the host receives more than one prefix from the connected
Internet Service Providers (ISP) and may have more than one source
addresses. Based on BCP 38, BCP 84 introduced recommendations on the
routing system for multihomed networks [RFC3704].
Recommendations on the routing system for ingress filtering such as
in BCP 84 inevitably involve source address checks. This leads us to
the source address dependent routing. Source address dependent
routing is an issue especially when the host is connected to a
multihomed network and is communicating with another host in another
multihomed network. In such a case, the communication can be broken
in both directions if ISPs apply ingress filtering and the datagrams
contain wrong source addresses
[I-D.huitema-multi6-ingress-filtering].
Sarikaya Expires August 24, 2015 [Page 2]
Internet-Draft SADR February 2015
Hosts with simultaneously active interfaces receive multiple prefixes
and have multiple source addresses. Datagrams originating from such
hosts carry greats risks to be dropped due to ingress filtering.
Source address selection algorithm needs to be careful to try to
avoid ingress filtering on the next-hop router [RFC6724].
Many use cases have been reported for source/destination routing in
[I-D.baker-rtgwg-src-dst-routing-use-cases]. These use cases clearly
indicate that the multihomed host or Customer Premises Equipment
(CPE) router needs to be configured with correct source prefixes/
addresses so that it can route packets upstream correctly to avoid
ingress filtering applied by an upstream ISP to drop the packets.
In multihomed networks there is a need to do source address based
routing if some providers are performing the ingress filtering
defined in BCP38 [RFC2827]. This requires the routers to consider
the source addresses as well as the destination addresses in
determining the next hop to send the packet to.
Based on the use cases defined in
[I-D.baker-rtgwg-src-dst-routing-use-cases], the routers may be
informed about the source addresses to use in routing using
extensions to the routing protocols like IS-IS defined in
[ISO.10589.1992] [I-D.baker-ipv6-isis-dst-src-routing] and OSPF
defined in [RFC5340] [I-D.baker-ipv6-ospf-dst-src-routing]. In this
document we describe the use cases for source address dependent
routing from the host perspective.
There are two cases. A host may have a single interface with
multiple addresses (from different prefixes or /64s). Each address
or prefix is connected to or coming from different exit routers, and
this case can be called multi-prefix multihoming (MPMH). A host may
have simultaneously connected multiple interfaces where each
interface is connected to a different exit router and this case can
be called multi-prefix multiple interface (MPMI).
It should be noted that Network Address and Port Translation (NAPT)
[RFC3022] in IPv4 and IPv6-to-IPv6 Network Prefix Translation (NPTv6)
[RFC6296] in IPv6 implement the functions of source address selection
and next-hop resolution and as such they address multihoming (and
hosts with multiple interfaces) requirements arising from source
address dependent routing [RFC7157]. In this case, the gateway
router or CPE router does the source address and next hop selection
for all the hosts connected to the router. However, for end-to-end
connectivity, NAPT and NPTv6 should be avoided and because of this,
NAPT and NPTv6 are left out of scope in this document.
Sarikaya Expires August 24, 2015 [Page 3]
Internet-Draft SADR February 2015
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
3. SADR Scenarios
Source address dependent routing can be facilitated at the host with
proper next hop and source address selection. For this, each router
connected to different interfaces of the host uses Router
Advertisements to distribute default route, next hop as well as
source address/prefix information to the host.
The use case shown in Figure 1 is multi-prefix multi interface use
case where rtr1 and rtr2 represent customer premises equipment/
routers (CPE) and there are exit routers in both network 1 and
network 2. The issue in this case is ingress filtering. If the
packets from the host communicating with a remote destination are
routed to the wrong exit router, i.e. carry wrong source address,
they will get dropped.
+------+ +------+ ___________
| | | | / \
| |-----| rtr1 |=====/ network \
| | | | \ 1 /
| | +------+ \___________/
| |
| host |
| |
| | +------+ ___________
| | | | / \
| |=====| rtr2 |=====/ network \
| | | | \ 2 /
+------+ +------+ \___________/
Figure 1: multiple Interfaced Host with Two CPE Routers
Our next use case is shown in Figure 2. This use case is a multi-
prefix multihoming use case. rtr is CPE router which is connected to
two ISPs each advertising their own prefixes. In this case, the host
may have a single interface but it receives multiple prefixes from
the connected ISPs. Assuming that ISPs apply ingress filtering
policy the packets for any external communication from the host
should follow source address dependent routing in order to avoid
getting dropped.
Sarikaya Expires August 24, 2015 [Page 4]
Internet-Draft SADR February 2015
+------+ |
| | |
| | |=====|(ISP1)|=====
| | +------+ |
| | | | |
| |=====| rtr |=====|
| host | | | |
| | +------+ |
| | |
| | |
| | |=====|(ISP2)|=====
| | |
+------+ |
Figure 2: Multihomed Host with Multiple CPE Routers
A variation of this use case is specialized egress routing. Upstream
networks offer different services with specific requirements, e.g.
video service. The hosts using this service need to use the
service's source and destination addresses. No other service will
accept this source address, i.e. those packets will be dropped
[I-D.baker-rtgwg-src-dst-routing-use-cases].
___________ +------+
/ \ +------+ | |
/ network \ | | | |
\ 1 /--| rtr1 |----| |
\___________/ | | | | +------+ ___________
+------+ | host | | | / \
| |=====| rtr3 |=====/ network \
___________ | | | | \ 3 /
/ \ +------+ | | +------+ \___________/
/ network \ | | | |
\ 2 /--| rtr2 |----| |
\___________/ | | | |
+------+ | |
+------+
Figure 3: multiple Interfaced Host with Three CPE Routers
Next use case is shown in Figure 3. It is a variation of multi-
prefix multi interface use case above. rtr1, rtr2 and rtr3 are CPE
Routers. The networks apply ingress routing. Source address
dependent routing should be used to avoid any external communications
be dropped.
Sarikaya Expires August 24, 2015 [Page 5]
Internet-Draft SADR February 2015
In the homenet scenario given in Figure 4, representing a simple home
network, there is a host connected to two CPEs which are connected to
ISP1 and ISP2, respectively. Each ISP provides a different prefix.
Also each router provides a different prefix to the host. The issue
in this scenario is also ingress filtering used by each ISP.
+------+
| | +------+
| | | |
| |==+==| rtr1 |=====|(ISP1)|=====
| | | | |
| | | +------+
| host | |
| | |
| | | +------+
| | | | |
| | +==| rtr2 |=====|(ISP2)|=====
| | | |
+------+ +------+
Figure 4: Simple Home Network with Two CPE Routers
The host has to select the source address from the prefixes of ISP1
or ISP2 when communicating with other hosts in ISP1 or ISP2. The
next issue is to select the correct next hop router, rtr1 or rtr2
that can reach the right ISP, ISP1 or ISP2.
+------+ | +------+
| | | | |
| | |-----| rtrF |=====ISP3
| | | | |
| | | +------+
| | |
| host | |
| | |
| | +------+ | +------+
| | | | | | |===== ISP2
| |=====| rtr |=====|=====| rtrE |
| | | | | | |===== ISP1
+------+ +------+ + +------+
Figure 5: Shim6 Host with Two Routers
The last use case in Figure 5 is also a variation of multi-prefix
multihoming use case above. In this case rtrE is connected to two
ISPs. All ISPs are assumed to apply ingress routing. The host
receives prefixes from each ISP and starts communicating with
Sarikaya Expires August 24, 2015 [Page 6]
Internet-Draft SADR February 2015
external hosts, e.g. H1, H2, etc. H1 and H2 may be accessible both
from ISP1 and ISP3.
The host receives multiple provider-allocated IPv6 address prefixes,
e.g. P1, P2 and P3 for ISP1, ISP2 and ISP3 and supports shim6
protocol [RFC5533]. rtr is a CPE router and the default router for
the host. rtr receives OSPF routes and has a default route for rtrE
and rtrF.
4. Analysis of Source Address Dependent Routing
In this section we present an analysis of the scenarios of Section 3
and then discuss the relevance of SADR to the provisioning domains.
4.1. Scenarios Analysis
As in [RFC7157] we assume that the routers in Section 3 use Router
Advertisements to distribute default route, next hop and source
address prefixes supported in each next hop to the hosts or the
gateway/CPE router relayes this information to the hosts.
Referring to the scenario in Figure 1, source address dependent
routing can present a solution to the problem of the host wishes to
reach a destination in network 2 and the host may choose rtr1 as the
default router. The solution should start with the correct
configuration of the host. The host should be configured with the
next hop addresses and the prefixes supported in these next hops.
This way the host having received many prefixes will have the correct
knowledge in selecting the right source address and next hop when
sending packets to remote destinations.
Note that similar considerations apply to the scenario in Figure 3.
In the configuration of the scenario in Figure 2 also it is useful to
configure the host with the next hop addresses and the prefixes and
source address prefixes they support. This will enable the host to
select the right prefix when sending packets to the right next hop
and avoid any ingress filtering.
Source address dependent routing in the use case of specialized
egress routing may work as follows. The specialized service router
advertizes one or more specific prefixes with appropriate source
prefixes, e.g. to the CPE Router, rtr in Figure 2. The CPE router in
turn advertizes the specific service's prefixes and source prefixes
to the host. This will allow proper configuration at the host so
that the host can use the service by sending the packets with the
correct source and destination addresses.
Sarikaya Expires August 24, 2015 [Page 7]
Internet-Draft SADR February 2015
Let us analyze the use case in Figure 4. If a source address
dependent routing protocol is used, the two routers (rtr1 and rtr2)
are both able to route traffic correctly, no matter which next-hop
router and source address the host selects. In case the host chooses
the wrong next hop router, e.g. for ISP2 rtr1 is selected, rtr1 will
forward the traffic to rtr2 to be sent to ISP2 and no ingress
filtering will happen.
Note that home networks are expected to comply with requirements for
source address dependent routing and the routers will be configured
accordingly, no matter which routing protocol, e.g. OSPF is used
[I-D.ietf-homenet-hncp].
This would work but with issues. The host traffic to ISP2 will have
to go over two links instead of one, i.e. the link bandwidth will be
halved. Another possibility is rtr1 can send an ICMPv6 Redirect
message to the host to direct the traffic to rtr2. Host would
redirect ISP2 traffic to rtr2.
The problem with redirects is that ICMPv6 Redirect message can only
convey two addresses, i.e. in this case the router address, or rtr2
address and the destination address, or the destination host in ISP2.
That means the source address will not be communicated. As a result,
the host would send packets to the same destination using both source
addresses which causes rtr2 to send a redirect message to rtr1,
resulting in ping-pong redirects sent by rtr1 and rtr2.
The best solution to these issues is to configure the host with both
the next hop and the source address prefixes that the next hop
supports. In homenets, each interface of the host can be configured
by its next hop, so that all that is needed is to add the information
on source address prefixes. This results in the hosts to select the
right router no matter what.
Finally, the use case in Figure 5 shows that even though all the
routers may have source address dependent routing support, the
packets still may get dropped.
The host in Figure 5 starts external communication with H1 and sends
the first packet with source address P3::iid. Since rtr has a
default route to rtrE it will use this default route in sending the
host's packet out towards rtrE. rtrE will route this packet to ISP1
and the packet will be dropped due to the ingress filtering.
A solution to this issue could be that rtrE having multiple routes to
H1 could use the path through rtrF and could direct the packet to the
other route, i.e. rtrF which would reach H1 in ISP3 without being
Sarikaya Expires August 24, 2015 [Page 8]
Internet-Draft SADR February 2015
subject to ingress routing
[I-D.baker-6man-multiprefix-default-route].
4.2. Provisioning Domains and SADR
Consistent set of network configuration information is called
provisioning domain (PvD). In case of multi-prefix multihoming
(MPMH), more than one provisioning domain is present on a single
link. In case of multi-prefix multiple interface (MPMI)
environments, elements of the same domain may be present on multiple
links. PvD aware nodes support association of configuration
information into PvDs and use these PvDs to serve requests for
network connections, e.g. chosing the right source address for the
packets. PvDs can be constructed from one of more DHCP or Router
Advertisement (RA) options carrying such information as PvD identity
and PvD container [I-D.ietf-mif-mpvd-ndp-support],
[I-D.ietf-mif-mpvd-dhcp-support]. PvDs constructed based on such
information are called explicit PvDs [I-D.ietf-mif-mpvd-arch].
Apart from PvD identity, PvD content may be encapsulated in separate
RA or DHCP options called PvD Container Option. Examples of such
content are defined in [I-D.sarikaya-6man-next-hop-ra] and
[I-D.sarikaya-dhc-6man-dhcpv6-sadr]. They constitute the content or
parts of the content of an explicit PvD.
Explicit PvDs may be received from different interfaces. Single PvD
may be accessible over one interface or simulatenously accessible
over multiple interfaces. Explicit PvDs may be scoped to a
configuration related to a particular interface, however in general
this may not apply. What matters is PvD ID provided that PvD ID is
authenticated by the node even in cases where the node has a single
connected interface. The authentication of the PvD ID should meet
the level required by the node policy. Single PvD information may be
received over multiple interfaces as long as PvD ID is the same.
This applies to the router advertisements (RAs) in which case a
multi-homed host (that is, with multiple interfaces) should trust a
message from a router on one interface to install a route to a
different router on another interface.
5. Guidelines on Standardization Work
We presented many topologies in which a host with multiple interfaces
or a multihomed host is connected to various networks or ISPs which
in turn may apply ingress routing. Our scenario analysis showed that
in order to avoid packets getting dropped due to ingress routing,
source address dependent routing is needed. Also, source address
dependent routing should be supported by routers throughout a site
that has multiple exits.
Sarikaya Expires August 24, 2015 [Page 9]
Internet-Draft SADR February 2015
In this section, we provide informative guidelines on different
existing and future solutions vis a vis the scenarios presented in
Section 3. We start with source address selection rule 5.5 and the
scenarios it solves and continue with solutions that state exactly
what information hosts need in terms of new router advertisement
options for correct source address selection in those scenarios.
5.1. Source Address Selection Rule 5.5
One possible solution is the default source address selection Rule
5.5 in [RFC6724] which recommends to select source addresses
advertized by the next hop. Considering the above scenarios, we can
state that this rule can solve the problem in Figure 1, Figure 2 and
Figure 3.
In using Rule 5.5 the following guidelines should be kept in mind.
Source address selection rules can be distributed by DHCP server
using DHCP Option OPTION_ADDRSEL_TABLE defined in [RFC7078].
In case of DHCP based host configuration, DHCP server can configure
only the interface of the host to which it is directly connected. In
order for Rule 5.5 to apply on other interfaces the option should be
sent on those interfaces as well using [RFC7078].
The default source address selection Rule 5.5 solves that problem
when an application sends a packet with an unspecified source
address. In the presence of two default routes, one route will be
chosen, and Rule 5.5 will make sure the right source address is used.
When the application selects a source address, i.e. the source
address is chosen before next-hop selection, even though the source
address is a way for the application to select the exit point, in
this case that purpose will not be served. In the presence of
multiple default routes, one will be picked, ignoring the source
address which was selected by the application because it is known
that IPv6 implementations are not required to remember which next-
hops advertised which prefixes. Therefore, the next-hop router may
not be the correct one, and the packets may be filtered.
This implies that the hosts should register which next-hop router
announced each prefix.
5.2. Router Advertisement Option
There is a need to configure the host not only with the next hops and
their prefixes but also with the source prefixes they support. Such
a configuration may avoid the host getting ingress/egress policy
error messages such as ICMP source address failure message.
Sarikaya Expires August 24, 2015 [Page 10]
Internet-Draft SADR February 2015
If host configuration is done using router advertisement messages
then there is a need to define new router advertisement options for
source address dependent routing. These options include Route Prefix
with Source Address/Prefix Option. Other options such as Next Hop
Address with Route Prefix option and Next Hop Address with Source
Address and Route Prefix option will be considered in Section 5.3.
As we observed in Section 4.1, the scenario in Figure 4 can be solved
by defining a new router advertisement option, i.e. Route Prefix
with Source Address/Prefix Option as defined in Section 13 in
[I-D.sarikaya-6man-next-hop-ra].
If host configuration is done using DHCP then there is a need to
define new DHCP options for Route Prefix with Source Address/Prefix.
As mentioned above, DHCP server configuration is interface specific.
New DHCP options for source address dependent routing such as route
prefix and source prefix need to be configured for each interface
separately.
The scenario in Figure 4 can be solved by defining a new DHCP option,
i.e. Route Prefix with Source Address/Prefix Option, if DHCP
configuration is a must.
5.3. Router Advertisement Option Set
The source address selection rule 5.5 may possibly be a solution for
selecting the right source addresses for each next hop but there are
cases where the next hop routers on each interface of the host are
not known by the host initially. A typical use case is the Virtual
Private Network (VPN) access. The host in VPN access is configured
by the VPN router which should also give the information on the next
hop routers and host needs to solicit the router advertisment using
RS/RA exchange.
The solution then calls for configuring hosts with Next Hop Addresses
and the Route Prefix, Source Address/Prefixes that they support. A
set of new router advertisement options as in
[I-D.sarikaya-6man-next-hop-ra] needs to be defined.
The guideline for this solution is that routers in the whole site
should be configured to provide the correct configuration information
to the hosts. This may result is fate sharing in which one router,
e.g. VPN router failure may effect the whole system. In order to
avoid such failures, the availability and reliability of routing
paths need to be provided using Virtual Router Redundancy Protocol
(VRRP) which is widely deployed in industry.
Sarikaya Expires August 24, 2015 [Page 11]
Internet-Draft SADR February 2015
Additional guideline for this solution is that regular router
operation calls for unsolicited router advertisements which are
commonly available in shared links. Also this type of operation does
not require inter router communication and thus avoids the fate
sharing, i.e. each router can autonomously operate independent of
other routers.
If host configuration is done using DHCP then there is a need to
define new DHCP options for Next Hop Address, Route Prefix with
Source Address/Prefix. Since DHCP server configuration is interface
specific, new DHCP options for source address dependent routing such
as next hop address, route prefix and source prefix need to be
configured for each interface separately.
The scenarios in Figure 1, Figure 2, Figure 3 and Figure 4 as well as
the ones involving the next hop addresses can be solved by defining
new DHCP options as in [I-D.sarikaya-dhc-6man-dhcpv6-sadr].
5.4. Other Solutions
So far we have singled out the scenario in Figure 5. All the above
solutions do not work in this case. This brings us the issue of IP
path probing [I-D.naderi-ipv6-probing].
For a given destination, the host selects a source address and a next
hop and sends its packet. When the selected path fails, in case of
IP probing, the host can probe all available paths until finding one
that works.
The guideline in probing is Source Address Dependent Routing (SADR)
should be used, i.e. it is a necessary tool. Basically, SADR saves
time in eliminating wrong paths, i.e. sending the packets to the
wrong exit router. If SADR is not taken into account correctly the
host will end up wasting resources trying to explore paths that are
certain to fail.
6. Security Considerations
This document describes some use cases and thus brings no new
security risks to the Internet.
7. IANA Considerations
None.
Sarikaya Expires August 24, 2015 [Page 12]
Internet-Draft SADR February 2015
8. Acknowledgements
In writing this document, we benefited from the ideas expressed by
the electronic mail discussion participants on 6man Working Group:
Brian Carpenter, Ole Troan, Pierre Pfister, Alex Petrescu, Ray
Hunter, Lorenzo Colitti and others. Pierre Pfister proposed the
scenario in Figure 4 as well as some text for Rule 5.5.
9. References
9.1. Normative References
[I-D.ietf-homenet-hncp]
Stenberg, M., Barth, S., and P. Pfister, "Home Networking
Control Protocol", draft-ietf-homenet-hncp-03 (work in
progress), January 2015.
[ISO.10589.1992]
International Organization for Standardization,
"Intermediate system to intermediate system intra-domain-
routing routine information exchange protocol for use in
conjunction with the protocol for providing the
connectionless-mode Network Service (ISO 8473), ISO
Standard 10589", ISO ISO.10589.1992, 1992.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
June 1999.
[RFC2827] Ferguson, P. and D. Senie, "Network Ingress Filtering:
Defeating Denial of Service Attacks which employ IP Source
Address Spoofing", BCP 38, RFC 2827, May 2000.
[RFC3022] Srisuresh, P. and K. Egevang, "Traditional IP Network
Address Translator (Traditional NAT)", RFC 3022, January
2001.
[RFC3704] Baker, F. and P. Savola, "Ingress Filtering for Multihomed
Networks", BCP 84, RFC 3704, March 2004.
[RFC3971] Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure
Neighbor Discovery (SEND)", RFC 3971, March 2005.
[RFC4191] Draves, R. and D. Thaler, "Default Router Preferences and
More-Specific Routes", RFC 4191, November 2005.
Sarikaya Expires August 24, 2015 [Page 13]
Internet-Draft SADR February 2015
[RFC4605] Fenner, B., He, H., Haberman, B., and H. Sandick,
"Internet Group Management Protocol (IGMP) / Multicast
Listener Discovery (MLD)-Based Multicast Forwarding
("IGMP/MLD Proxying")", RFC 4605, August 2006.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
September 2007.
[RFC4862] Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
Address Autoconfiguration", RFC 4862, September 2007.
[RFC5340] Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
for IPv6", RFC 5340, July 2008.
[RFC5533] Nordmark, E. and M. Bagnulo, "Shim6: Level 3 Multihoming
Shim Protocol for IPv6", RFC 5533, June 2009.
[RFC6106] Jeong, J., Park, S., Beloeil, L., and S. Madanapalli,
"IPv6 Router Advertisement Options for DNS Configuration",
RFC 6106, November 2010.
[RFC6296] Wasserman, M. and F. Baker, "IPv6-to-IPv6 Network Prefix
Translation", RFC 6296, June 2011.
[RFC6724] Thaler, D., Draves, R., Matsumoto, A., and T. Chown,
"Default Address Selection for Internet Protocol Version 6
(IPv6)", RFC 6724, September 2012.
[RFC7078] Matsumoto, A., Fujisaki, T., and T. Chown, "Distributing
Address Selection Policy Using DHCPv6", RFC 7078, January
2014.
[RFC7157] Troan, O., Miles, D., Matsushima, S., Okimoto, T., and D.
Wing, "IPv6 Multihoming without Network Address
Translation", RFC 7157, March 2014.
9.2. Informative References
[I-D.baker-6man-multiprefix-default-route]
Baker, F., "Multiprefix IPv6 Routing for Ingress Filters",
draft-baker-6man-multiprefix-default-route-00 (work in
progress), November 2007.
[I-D.baker-ipv6-isis-dst-src-routing]
Baker, F. and D. Lamparter, "IPv6 Source/Destination
Routing using IS-IS", draft-baker-ipv6-isis-dst-src-
routing-02 (work in progress), October 2014.
Sarikaya Expires August 24, 2015 [Page 14]
Internet-Draft SADR February 2015
[I-D.baker-ipv6-ospf-dst-src-routing]
Baker, F., "IPv6 Source/Destination Routing using OSPFv3",
draft-baker-ipv6-ospf-dst-src-routing-03 (work in
progress), August 2013.
[I-D.baker-rtgwg-src-dst-routing-use-cases]
Baker, F., "Requirements and Use Cases for Source/
Destination Routing", draft-baker-rtgwg-src-dst-routing-
use-cases-01 (work in progress), October 2014.
[I-D.huitema-multi6-ingress-filtering]
Huitema, C., "Ingress filtering compatibility for IPv6
multihomed sites", draft-huitema-multi6-ingress-
filtering-00 (work in progress), October 2004.
[I-D.ietf-mif-mpvd-arch]
Anipko, D., "Multiple Provisioning Domain Architecture",
draft-ietf-mif-mpvd-arch-10 (work in progress), February
2015.
[I-D.ietf-mif-mpvd-dhcp-support]
Krishnan, S., Korhonen, J., and S. Bhandari, "Support for
multiple provisioning domains in DHCPv6", draft-ietf-mif-
mpvd-dhcp-support-00 (work in progress), August 2014.
[I-D.ietf-mif-mpvd-ndp-support]
Korhonen, J., Krishnan, S., and S. Gundavelli, "Support
for multiple provisioning domains in IPv6 Neighbor
Discovery Protocol", draft-ietf-mif-mpvd-ndp-support-00
(work in progress), August 2014.
[I-D.naderi-ipv6-probing]
Naderi, H. and B. Carpenter, "Experience with IPv6 path
probing", draft-naderi-ipv6-probing-00 (work in progress),
October 2014.
[I-D.sarikaya-6man-next-hop-ra]
Sarikaya, B., "IPv6 RA Options for Next Hop Routes",
draft-sarikaya-6man-next-hop-ra-04 (work in progress),
December 2014.
[I-D.sarikaya-dhc-6man-dhcpv6-sadr]
Sarikaya, B., "DHCPv6 Route Options for Source Address
Dependent Routing", draft-sarikaya-dhc-6man-dhcpv6-sadr-00
(work in progress), December 2014.
Sarikaya Expires August 24, 2015 [Page 15]
Internet-Draft SADR February 2015
Author's Address
Behcet Sarikaya
Huawei USA
5340 Legacy Dr. Building 175
Plano, TX 75024
Email: sarikaya@ieee.org
Sarikaya Expires August 24, 2015 [Page 16]