IDR                                                               F. Qin
Internet-Draft                                              China Mobile
Intended status: Standards Track                                 H. Yuan
Expires: March 6, 2021                                          UnionPay
                                                                 T. Zhou
                                                             G. Fioccola
                                                                 Y. Wang
                                                                  Huawei
                                                       September 2, 2020


                BGP SR Policy Extensions to Enable IFIT
                    draft-qin-idr-sr-policy-ifit-03

Abstract

   Segment Routing (SR) policy is a set of candidate SR paths consisting
   of one or more segment lists and necessary path attributes.  It
   enables instantiation of an ordered list of segments with a specific
   intent for traffic steering.  In-situ Flow Information Telemetry
   (IFIT) refers to network OAM data plane on-path telemetry techniques,
   in particular the most popular are In-situ OAM (IOAM) and Alternate
   Marking.  This document defines extensions to BGP to distribute SR
   policies carrying IFIT information.  So that IFIT methods can be
   enabled automatically when the SR policy is applied.

Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 6, 2021.



Qin, et al.               Expires March 6, 2021                 [Page 1]


Internet-Draft             bgp-sr-policy-ifit             September 2020


Copyright Notice

   Copyright (c) 2020 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Motivation  . . . . . . . . . . . . . . . . . . . . . . . . .   3
   3.  IFIT Attributes in SR Policy  . . . . . . . . . . . . . . . .   4
   4.  SR Policy for IOAM  . . . . . . . . . . . . . . . . . . . . .   5
     4.1.  IOAM Pre-allocated Trace Option Sub-TLV . . . . . . . . .   5
     4.2.  IOAM Incremental Trace Option Sub-TLV . . . . . . . . . .   6
     4.3.  IOAM Directly Export Option Sub-TLV . . . . . . . . . . .   6
     4.4.  IOAM Edge-to-Edge Option Sub-TLV  . . . . . . . . . . . .   7
   5.  SR Policy for Enhanced Alternate Marking  . . . . . . . . . .   8
   6.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   9
   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  10
   8.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  10
   9.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  10
     9.1.  Normative References  . . . . . . . . . . . . . . . . . .  10
     9.2.  Informative References  . . . . . . . . . . . . . . . . .  11
   Appendix A. . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  12

1.  Introduction

   Segment Routing (SR) policy [I-D.ietf-spring-segment-routing-policy]
   is a set of candidate SR paths consisting of one or more segment
   lists and necessary path attributes.  It enables instantiation of an
   ordered list of segments with a specific intent for traffic steering.

   In-situ Flow Information Telemetry (IFIT) denotes a family of flow-
   oriented on-path telemetry techniques (e.g.  IOAM, Alternate
   Marking), which can provide high-precision flow insight and real-time
   network issue notification (e.g., jitter, latency, packet loss).In
   particular, IFIT refers to network OAM data plane on-path telemetry
   techniques, including In-situ OAM (IOAM) [I-D.ietf-ippm-ioam-data]



Qin, et al.               Expires March 6, 2021                 [Page 2]


Internet-Draft             bgp-sr-policy-ifit             September 2020


   and Alternate Marking [RFC8321].  It can provide flow information on
   the entire forwarding path on a per- packet basis in real time.

   An automatic network requires the Service Level Agreement (SLA)
   monitoring on the deployed service.  So that the system can quickly
   detect the SLA violation or the performance degradation, hence to
   change the service deployment.  For this reason, the SR policy native
   IFIT can facilitate the closed loop control and enable the automation
   of SR service.

   This document defines extensions to Border Gateway Protocol (BGP) to
   distribute SR policies carrying IFIT information.  So that IFIT
   behavior can be enabled automatically when the SR policy is applied.

   This BGP extension allows to signal the IFIT capabilities together
   with the SR-policy.  In this way IFIT methods are automatically
   activated and running.  The flexibility and dynamicity of the IFIT
   applications are given by the use of additional functions on the
   controller and on the network nodes, but this is out of scope here.

2.  Motivation

   IFIT Methods are being introduced in multiple protocols and below is
   a proper picture of the relevant documents for Segment Routing.
   Indeed the IFIT methods are becoming mature for Segment Routing over
   the MPLS data plane (SR-MPLS) and Segment Routing over IPv6 data
   plane (SRv6), that is the main focus of this draft:

      IOAM: the reference documents for the data plane are
      [I-D.ietf-ippm-ioam-ipv6-options] for SRv6 and
      [I-D.gandhi-mpls-ioam-sr] for SR-MPLS.

      Alternate Marking: the reference documents for the data plane are
      [I-D.ietf-6man-ipv6-alt-mark] for SRv6 and
      [I-D.ietf-mpls-rfc6374-sfl], [I-D.gandhi-mpls-rfc6374-sr] for SR-
      MPLS.

   The definition of these data plane IFIT methods for SR-MPLS and SRv6
   imply requirements for various routing protocols, such as BGP, and
   this document aims to define BGP extensions to distribute SR policies
   carrying IFIT information.  This allows to signal the IFIT
   capabilities so IFIT methods are automatically configured and ready
   to run when the SR Policy candidate paths are distributed through
   BGP.

   It is to be noted that, for PCEP, [I-D.chen-pce-pcep-ifit] proposes
   the extensions to PCEP to distribute paths carrying IFIT information
   and therefore to enable IFIT methods for SR policy too.



Qin, et al.               Expires March 6, 2021                 [Page 3]


Internet-Draft             bgp-sr-policy-ifit             September 2020


3.  IFIT Attributes in SR Policy

   As defined in [I-D.ietf-idr-segment-routing-te-policy], the SR Policy
   encoding structure is as follows:

         SR Policy SAFI NLRI: <Distinguisher, Policy-Color, Endpoint>
         Attributes:
            Tunnel Encaps Attribute (23)
               Tunnel Type: SR Policy
                   Binding SID
                   Preference
                   Priority
                   Policy Name
                   Explicit NULL Label Policy (ENLP)
                   Segment List
                       Weight
                       Segment
                       Segment
                       ...
                   ...

   A candidate path includes multiple SR paths, each of which is
   specified by a segment list.  IFIT can be applied to the candidate
   path, so that all the SR paths can be monitored in the same way.  The
   new SR Policy encoding structure is expressed as below:

         SR Policy SAFI NLRI: <Distinguisher, Policy-Color, Endpoint>
         Attributes:
            Tunnel Encaps Attribute (23)
               Tunnel Type: SR Policy
                   Binding SID
                   Preference
                   Priority
                   Policy Name
                   Explicit NULL Label Policy (ENLP)
                   IFIT Attributes
                   Segment List
                       Weight
                       Segment
                       Segment
                       ...
                   ...

   IFIT attributes can be attached at the candidate path level as sub-
   TLVs.  There may be different IFIT tools.  The following sections
   will describe the requirement and usage of different IFIT tools, and
   define the corresponding sub-TLV encoding in BGP.




Qin, et al.               Expires March 6, 2021                 [Page 4]


Internet-Draft             bgp-sr-policy-ifit             September 2020


   Note that the IFIT attributes here described can also be generalized
   and included as sub-TLVs for other SAFIs and NLRIs.

4.  SR Policy for IOAM

   In-situ Operations, Administration, and Maintenance (IOAM)
   [I-D.ietf-ippm-ioam-data] records operational and telemetry
   information in the packet while the packet traverses a path between
   two points in the network.  In terms of the classification given in
   RFC 7799 [RFC7799] IOAM could be categorized as Hybrid Type 1.  IOAM
   mechanisms can be leveraged where active OAM do not apply or do not
   offer the desired results.

   When SR policy enables the IOAM, the IOAM header will be inserted
   into every packet of the traffic that is steered into the SR paths.

   This document aims to define the control plane.  While a relevant
   document for the data plane is [I-D.ietf-ippm-ioam-ipv6-options] for
   Segment Routing over IPv6 data plane (SRv6).

4.1.  IOAM Pre-allocated Trace Option Sub-TLV

   The IOAM tracing data is expected to be collected at every node that
   a packet traverses to ensure visibility into the entire path a packet
   takes within an IOAM domain.  The preallocated tracing option will
   create pre-allocated space for each node to populate its information.

   The format of IOAM pre-allocated trace option sub-TLV is defined as
   follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +---------------+---------------+-------------------------------+
   |      Type     |    Length     |    Namespace ID               |
   +---------------+---------------+--------------+--------+-------+
   |         IOAM Trace Type                      | Flags  | Rsvd  |
   +----------------------------------------------+--------+-------+

              Fig. 1 IOAM Pre-allocated Trace Option Sub-TLV

   Where:

   Type: to be assigned by IANA.

   Length: the total length of the value field not including Type and
   Length fields.





Qin, et al.               Expires March 6, 2021                 [Page 5]


Internet-Draft             bgp-sr-policy-ifit             September 2020


   Namespace ID: A 16-bit identifier of an IOAM-Namespace.  The
   definition is the same as described in section 4.4 of
   [I-D.ietf-ippm-ioam-data].

   IOAM Trace Type: A 24-bit identifier which specifies which data types
   are used in the node data list.  The definition is the same as
   described in section 4.4 of [I-D.ietf-ippm-ioam-data].

   Flags: A 4-bit field.  The definition is the same as described in
   [I-D.ietf-ippm-ioam-flags] and section 4.4 of
   [I-D.ietf-ippm-ioam-data].

   Rsvd: A 4-bit field reserved for further usage.  It MUST be zero.

4.2.  IOAM Incremental Trace Option Sub-TLV

   The incremental tracing option contains a variable node data fields
   where each node allocates and pushes its node data immediately
   following the option header.

   The format of IOAM incremental trace option sub-TLV is defined as
   follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +---------------+---------------+-------------------------------+
   |      Type     |    Length     |    Namespace ID               |
   +---------------+---------------+--------------+--------+-------+
   |         IOAM Trace Type                      | Flags  | Rsvd  |
   +----------------------------------------------+--------+-------+

               Fig. 2 IOAM Incremental Trace Option Sub-TLV

   Where:

   Type: to be assigned by IANA.

   Length: the total length of the value field not including Type and
   Length fields.

   All the other fields definistion is the same as the pre-allocated
   trace option sub-TLV in section 4.1.

4.3.  IOAM Directly Export Option Sub-TLV

   IOAM directly export option is used as a trigger for IOAM data to be
   directly exported to a collector without being pushed into in-flight
   data packets.



Qin, et al.               Expires March 6, 2021                 [Page 6]


Internet-Draft             bgp-sr-policy-ifit             September 2020


   The format of IOAM directly export option sub-TLV is defined as
   follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                   +---------------+---------------+
                                   |    Type       |    Length     |
   +-----------------------------------------------+---------------+
   |        Namespace ID           |            Flags              |
   +-------------------------------+---------------+---------------+
   |               IOAM Trace Type                 |      Rsvd     |
   +-----------------------------------------------+---------------+
   |                         Flow ID                               |
   +---------------------------------------------------------------+

                Fig. 3 IOAM Directly Export Option Sub-TLV

   Where:

   Type: to be assigned by IANA.

   Length: the total length of the value field not including Type and
   Length fields.

   Namespace ID: A 16-bit identifier of an IOAM-Namespace.  The
   definition is the same as described in section 4.4 of
   [I-D.ietf-ippm-ioam-data].

   IOAM Trace Type: A 24-bit identifier which specifies which data types
   are used in the node data list.  The definition is the same as
   described in section 4.4 of [I-D.ietf-ippm-ioam-data].

   Flags: A 16-bit field.  The definition is the same as described in
   section 3.2 of [I-D.ietf-ippm-ioam-direct-export].

   Flow ID: A 32-bit flow identifier.  The definition is the same as
   described in section 3.2 of [I-D.ietf-ippm-ioam-direct-export].

   Rsvd: A 4-bit field reserved for further usage.  It MUST be zero.

4.4.  IOAM Edge-to-Edge Option Sub-TLV

   The IOAM edge to edge option is to carry data that is added by the
   IOAM encapsulating node and interpreted by IOAM decapsulating node.

   The format of IOAM edge-to-edge option sub-TLV is defined as follows:





Qin, et al.               Expires March 6, 2021                 [Page 7]


Internet-Draft             bgp-sr-policy-ifit             September 2020


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                   +---------------+---------------+
                                   |      Type     |     Length    |
   +-----------------------------------------------+---------------+
   |        Namespace ID           |         IOAM E2E Type         |
   +-------------------------------+-------------------------------+

                  Fig. 4 IOAM Edge-to-Edge Option Sub-TLV

   Where:

   Type: to be assigned by IANA.

   Length: the total length of the value field not including Type and
   Length fields.

   Namespace ID: A 16-bit identifier of an IOAM-Namespace.  The
   definition is the same as described in section 4.6 of
   [I-D.ietf-ippm-ioam-data].

   IOAM E2E Type: A 16-bit identifier which specifies which data types
   are used in the E2E option data.  The definition is the same as
   described in section 4.6 of [I-D.ietf-ippm-ioam-data].

5.  SR Policy for Enhanced Alternate Marking

   The Alternate Marking [RFC8321]technique is an hybrid performance
   measurement method, per RFC 7799 [RFC7799] classification of
   measurement methods.  Because this method is based on marking
   consecutive batches of packets.  It can be used to measure packet
   loss, latency, and jitter on live traffic.

   This document aims to define the control plane.  While a relevant
   document for the data plane is [I-D.ietf-6man-ipv6-alt-mark] for
   Segment Routing over IPv6 data plane (SRv6).

   The format of Enhanced Alternate Marking (EAM) sub-TLV is defined as
   follows:












Qin, et al.               Expires March 6, 2021                 [Page 8]


Internet-Draft             bgp-sr-policy-ifit             September 2020


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
                                   +---------------+---------------+
                                   |    Type       |    Length     |
   +-------------------------------+-------+-------+-------+-------+
   |           FlowMonID                   |     Period    | Rsvd  |
   +---------------------------------------+---------------+-------+

                 Fig. 5 Enhanced Alternate Marking Sub-TLV

   Where:

   Type: to be assigned by IANA.

   Length: the total length of the value field not including Type and
   Length fields.

   FlowMonID: A 20-bit identifier to uniquely identify a monitored flow
   within the measurement domain.  The definition is the same as
   described in section 5.3 of [I-D.ietf-6man-ipv6-alt-mark].

   Period: Time interval between two alternate marking period.  The unit
   is second.

   Rsvd: A 4-bit field reserved for further usage.  It MUST be zero.

6.  IANA Considerations

   This document defines new sub-TLVs in the registry "BGP Tunnel
   Encapsulation Attribute sub-TLVs" to be assigned by IANA:

   Codepoint    Description                      Reference
   -------------------------------------------------------------
   TBD1         IOAM Pre-allocated Trace         This document
                Option Sub-TLV
   TBD2         IOAM Incremental Trace           This document
                Option Sub-TLV
   TBD3         IOAM Directly Export             This document
                Option Sub-TLV
   TBD4         IOAM Edge-to-Edge                This document
                Option Sub-TLV
   TBD5         Enhanced Alternate Marking       This document
                Sub-TLV








Qin, et al.               Expires March 6, 2021                 [Page 9]


Internet-Draft             bgp-sr-policy-ifit             September 2020


7.  Security Considerations

   The security mechanisms of the base BGP security model apply to the
   extensions described in this document as well.  See the Security
   Considerations section of [I-D.ietf-idr-segment-routing-te-policy].

   SR operates within a trusted SR domain RFC 8402 [RFC8402] and its
   security considerations also apply to BGP sessions when carrying SR
   Policy information.  The isolation of BGP SR Policy SAFI peering
   sessions may be used to ensure that the SR Policy information is not
   advertised outside the SR domain.  Additionally, only trusted nodes
   (that include both routers and controller applications) within the SR
   domain must be configured to receive such information.

   Implementation of IFIT methods (IOAM and Alternate Marking) are
   mindful of security and privacy concerns, as explained in
   [I-D.ietf-ippm-ioam-data] and RFC 8321 [RFC8321].  Anyway incorrect
   IFIT parameters in the BGP extension SHOULD not have an adverse
   effect on the SR Policy as well as on the network, since it affects
   only the operation of the telemetry methodology.

8.  Acknowledgements

   The authors of this document would like to thank Ketan Talaulikar and
   Joel Halpern for their comments and review of this document.

9.  References

9.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC7799]  Morton, A., "Active and Passive Metrics and Methods (with
              Hybrid Types In-Between)", RFC 7799, DOI 10.17487/RFC7799,
              May 2016, <https://www.rfc-editor.org/info/rfc7799>.

   [RFC8321]  Fioccola, G., Ed., Capello, A., Cociglio, M., Castaldelli,
              L., Chen, M., Zheng, L., Mirsky, G., and T. Mizrahi,
              "Alternate-Marking Method for Passive and Hybrid
              Performance Monitoring", RFC 8321, DOI 10.17487/RFC8321,
              January 2018, <https://www.rfc-editor.org/info/rfc8321>.







Qin, et al.               Expires March 6, 2021                [Page 10]


Internet-Draft             bgp-sr-policy-ifit             September 2020


   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

9.2.  Informative References

   [I-D.chen-pce-pcep-ifit]
              Chen, H., Yuan, H., Zhou, T., Li, W., Fioccola, G., and Y.
              Wang, "Path Computation Element Communication Protocol
              (PCEP) Extensions to Enable IFIT", draft-chen-pce-pcep-
              ifit-00 (work in progress), August 2020.

   [I-D.gandhi-mpls-ioam-sr]
              Gandhi, R., Ali, Z., Filsfils, C., Brockners, F., Wen, B.,
              and V. Kozak, "MPLS Data Plane Encapsulation for In-situ
              OAM Data", draft-gandhi-mpls-ioam-sr-02 (work in
              progress), March 2020.

   [I-D.gandhi-mpls-rfc6374-sr]
              Gandhi, R., Filsfils, C., Voyer, D., Salsano, S., and M.
              Chen, "Performance Measurement Using RFC 6374 for Segment
              Routing Networks with MPLS Data Plane", draft-gandhi-mpls-
              rfc6374-sr-05 (work in progress), June 2020.

   [I-D.ietf-6man-ipv6-alt-mark]
              Fioccola, G., Zhou, T., Cociglio, M., Qin, F., and R.
              Pang, "IPv6 Application of the Alternate Marking Method",
              draft-ietf-6man-ipv6-alt-mark-01 (work in progress), June
              2020.

   [I-D.ietf-idr-segment-routing-te-policy]
              Previdi, S., Filsfils, C., Talaulikar, K., Mattes, P.,
              Rosen, E., Jain, D., and S. Lin, "Advertising Segment
              Routing Policies in BGP", draft-ietf-idr-segment-routing-
              te-policy-09 (work in progress), May 2020.

   [I-D.ietf-ippm-ioam-data]
              Brockners, F., Bhandari, S., and T. Mizrahi, "Data Fields
              for In-situ OAM", draft-ietf-ippm-ioam-data-10 (work in
              progress), July 2020.

   [I-D.ietf-ippm-ioam-direct-export]
              Song, H., Gafni, B., Zhou, T., Li, Z., Brockners, F.,
              Bhandari, S., Sivakolundu, R., and T. Mizrahi, "In-situ
              OAM Direct Exporting", draft-ietf-ippm-ioam-direct-
              export-01 (work in progress), August 2020.




Qin, et al.               Expires March 6, 2021                [Page 11]


Internet-Draft             bgp-sr-policy-ifit             September 2020


   [I-D.ietf-ippm-ioam-flags]
              Mizrahi, T., Brockners, F., Bhandari, S., Sivakolundu, R.,
              Pignataro, C., Kfir, A., Gafni, B., Spiegel, M., and J.
              Lemon, "In-situ OAM Flags", draft-ietf-ippm-ioam-flags-02
              (work in progress), July 2020.

   [I-D.ietf-ippm-ioam-ipv6-options]
              Bhandari, S., Brockners, F., Pignataro, C., Gredler, H.,
              Leddy, J., Youell, S., Mizrahi, T., Kfir, A., Gafni, B.,
              Lapukhov, P., Spiegel, M., Krishnan, S., and R. Asati,
              "In-situ OAM IPv6 Options", draft-ietf-ippm-ioam-
              ipv6-options-02 (work in progress), July 2020.

   [I-D.ietf-mpls-rfc6374-sfl]
              Bryant, S., Swallow, G., Chen, M., Fioccola, G., and G.
              Mirsky, "RFC6374 Synonymous Flow Labels", draft-ietf-mpls-
              rfc6374-sfl-07 (work in progress), June 2020.

   [I-D.ietf-spring-segment-routing-policy]
              Filsfils, C., Talaulikar, K., Voyer, D., Bogdanov, A., and
              P. Mattes, "Segment Routing Policy Architecture", draft-
              ietf-spring-segment-routing-policy-08 (work in progress),
              July 2020.

Appendix A.

Authors' Addresses

   Fengwei Qin
   China Mobile
   No. 32 Xuanwumenxi Ave., Xicheng District
   Beijing
   China

   Email: qinfengwei@chinamobile.com


   Hang Yuan
   UnionPay
   1899 Gu-Tang Rd., Pudong
   Shanghai
   China

   Email: yuanhang@unionpay.com







Qin, et al.               Expires March 6, 2021                [Page 12]


Internet-Draft             bgp-sr-policy-ifit             September 2020


   Tianran Zhou
   Huawei
   156 Beiqing Rd., Haidian District
   Beijing
   China

   Email: zhoutianran@huawei.com


   Giuseppe Fioccola
   Huawei
   Riesstrasse, 25
   Munich
   Germany

   Email: giuseppe.fioccola@huawei.com


   Yali Wang
   Huawei
   156 Beiqing Rd., Haidian District
   Beijing
   China

   Email: wangyali11@huawei.com


























Qin, et al.               Expires March 6, 2021                [Page 13]