DTNRG H. Kruse
Internet-Draft S. Jero
Intended status: Experimental S. Ostermann
Expires: August 5, 2013 Ohio University
Feb 2013
Datagram Convergence Layers for the DTN Bundle and LTP Protocols
draft-irtf-dtnrg-dgram-clayer-02
Abstract
This document is a product of the DTNRG Research Group. It specifies
the preferred method for transporting DTN protocol data over the
Internet using datagrams. The specification covers convergence
layers for the Bundle Protocol as well as the transportation of LTP
segments. UDP and DCCP are the candidate datagram protocols
discussed. UDP can only be used on a local network, or in cases
where the DTN node implements explicit congestion control. DCCP
addresses the congestion control problem, and its use is recommended
whenever possible.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on August 5, 2013.
Copyright Notice
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
Kruse, et al. Expires August 5, 2013 [Page 1]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 3
2. General Recommendation . . . . . . . . . . . . . . . . . . . . 3
3. Recommendations for Implementers . . . . . . . . . . . . . . . 4
3.1. How and Where to Deal with Fragmentation . . . . . . . . . 4
3.1.1. DCCP . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.1.2. UDP . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.2. Bundle Protocol over a Datagram Convergence Layer . . . . 5
3.2.1. DCCP . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.2.2. UDP . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.3. LTP over Datagrams . . . . . . . . . . . . . . . . . . . . 6
3.3.1. DCCP . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.3.2. UDP . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.4. Keep Alive Option . . . . . . . . . . . . . . . . . . . . 6
3.5. Checksums . . . . . . . . . . . . . . . . . . . . . . . . 6
3.5.1. DCCP . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.5.2. UDP . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.6. DCCP Congestion Control Modules . . . . . . . . . . . . . 7
4. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
5. Security Considerations . . . . . . . . . . . . . . . . . . . 7
6. References . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.1. Normative References . . . . . . . . . . . . . . . . . . . 8
6.2. Informative References . . . . . . . . . . . . . . . . . . 9
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 10
Kruse, et al. Expires August 5, 2013 [Page 2]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
1. Introduction
Delay/Disruption Tolerant Network (DTN) communication protocols
include the Bundle Protocol described in RFC 5050 [RFC5050], which
provides transmission of application data blocks (Bundles) through
optional intermediate custody transfer, and the Licklider
Transmission Protocol (LTP), RFCs 5325 (LTP Motivation) [RFC5325],
5326 (LTP Specification) [RFC5326], and 5327 (LTP Security) [RFC5327]
which can be used to transmit Bundles reliably and efficiently over a
point to point link. It is often desirable to test these protocols
over Internet Protocol links. draft-irtf-dtnrg-tcp-clayer
[I-D.irtf-dtnrg-tcp-clayer] defines a method for transporting Bundles
over TCP. This draft specifies the preferred method for transmitting
either Bundles or LTP blocks across the Internet using datagrams in
place of TCP. This document represents the consensus of the DTNRG
RG.
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. General Recommendation
In order to utilize DTN protocols across the Internet, whether for
testing purposes or as part of a larger network path, it is necessary
to encapsulate them into a standard Internet protocol so that they
travel easily across the Internet. This is particularly true for
LTP, which provides no endpoint addressing. This encapsulation
choice needs to be made carefully in order to avoid redundancy, since
DTN protocols may provide their own reliability mechanisms.
Congestion control is vital to the continued functioning of the
Internet, particularly for situations where data will be sent at
arbitrarily fast data rates. The Bundle Protocol delegates provision
of reliable delivery and, implicitly, congestion control to the
convergence layer used (Section 7.2 of RFC 5050 [RFC5050]). In
situations where TCP will work effectively in communications between
pairs of DTN nodes, use of the TCP convergence layer
draft-irtf-dtnrg-tcp-clayer [I-D.irtf-dtnrg-tcp-clayer] will provide
the required reliability and congestion control for transport of
Bundles and would be the default choice in the Internet.
Alternatives such as encapsulating Bundles in directly in datagrams
and using UDP or the Datagram Congestion Control Protocol (DCCP) are
not generally appropriate because they offer limited reliability and,
in the case of UDP, no congestion control.
Kruse, et al. Expires August 5, 2013 [Page 3]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
LTP, on the other hand, offers its own form of reliability.
Particularly for testing purposes, it makes no sense to run LTP over
a protocol, like TCP, that offers reliability already. In addition,
running LTP over TCP would reduce the flexibility available to users,
since LTP offers more control over what data is delivered reliably
and what data is delivered best effort, a feature that TCP lacks. As
such, it would be better to run LTP over an unreliable protocol.
One solution would be to use UDP. UDP provides no reliability,
allowing LTP to manage that itself. However, UDP does not provide
congestion control. Because LTP is designed to run over fixed rate
radio links it does provides rate control, but not congestion
control. Lack of congestion control in network connections is a
major problem that can cause artificially high loss rates and/or
serious fairness issues. Previous standards documents are unanimous
in recommending congestion control for protocols to be used on the
Internet, see "Congestion Control Principles" [RFC2914], "Unicast UDP
Usage Guidelines" [RFC5405], and "Queue Management and Congestion
Avoidance" [RFC2309], among others. RFC 5405, in particular, calls
congestion control "vital" for "applications that can operate at
higher, potentially unbounded data rates". Therefore, any Bundle
Protocol implementation permitting the use of UDP to transport LTP
segments or Bundles outside an isolated network for the transmission
of any non-trivial amounts of data MUST implement congestion control
consistent with RFC 5405.
Alternatively, the Datagram Congestion Control Protocol (DCCP)
[RFC4340] was designed specifically to provide congestion control
without reliability for those applications that traverse the Internet
but do not desire to retransmit lost data. As such, it is
RECOMMENDED that, if possible, DCCP be used to transport LTP segments
across the Internet.
3. Recommendations for Implementers
3.1. How and Where to Deal with Fragmentation
The Bundle Protocol allows Bundles with sizes limited only by node
resource constraints. In IPv4, the maximum size of a UDP datagram is
nearly 64KB. In IPv6, when using jumbograms [RFC2675], UDP datagrams
can technically be up to 4GB in size [RFC2147], although this options
is rarely used. It is well understood that sending large IP
datagrams that must be fragmented by the network has enormous
efficiency penalties [Kent88]. The Bundle protocol specification
provides a Bundle fragmentation concept [RFC5050] that allows a large
Bundle to be divided into Bundle fragments. If the Bundle Protocol
is being encapsulated in DCCP or UDP, it therefore SHOULD create each
Kruse, et al. Expires August 5, 2013 [Page 4]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
fragment of sufficiently small size that it can then be encapsulated
into a datagram that will not need to be fragmented at the IP layer.
IP fragmentation can be avoided by using IP Path MTU Discovery
[RFC1191][RFC1981], which depends on the deterministic delivery of
ICMP Packet Too Big (PTB) messages from routers in the network. To
bypass a condition referred to as a black hole [RFC2923], a newer
specification is available in [RFC4821] to determine the IP Path MTU
without the use of PTB messages.
3.1.1. DCCP
Because DCCP implementations are not required to support IP
fragmentation and are not allowed to enable it by default, a DCCP
Convergence Layer (we will use "CL" from here on) MUST NOT accept
data segments that cannot be sent as one MTU sized datagram.
3.1.2. UDP
When an LTP CL is using UDP for datagram delivery, it SHOULD NOT
create segments that will result in UDP datagrams that will need to
be fragmented, as discussed above.
3.2. Bundle Protocol over a Datagram Convergence Layer
In general, the use of the Bundle protocol over a datagram CL is
discouraged in IP networks. Bundles can be of (almost) arbitrary
length, and the Bundle protocol does not include an effective
retransmission mechanism. Whenever possible the Bundle protocol
SHOULD be operated over the TCP Convergence Layer or over LTP.
If a datagram CL is used for transmission of Bundles, every datagram
MUST contain exactly one Bundle or four zero octets as a keep-alive.
Bundles that are too large for the path MTU SHOULD be fragmented at
the Bundle protocol layer to prevent IP fragmentation.
3.2.1. DCCP
The DCCP CL for Bundle protocol use SHOULD use the IANA assigned port
4556/DCCP and service code 1685351985; the use of other port numbers
and service codes is implementation specific.
3.2.2. UDP
The UDP CL for Bundle protocol use SHOULD use the IANA assigned port
4556/UDP; the use of other port numbers is implementation specific.
Kruse, et al. Expires August 5, 2013 [Page 5]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
3.3. LTP over Datagrams
LTP is designed as a point to point protocol within DTN, and it
provides intrinsic acknowledgement and retransmission facilities.
LTP segments are transported over a "local data link layer" (RFC 5325
[RFC5325]); we will use the term "transport" from here on. Transport
of LTP using datagrams is an appropriate choice. When a datagram
transport is used to send LTP segments, every datagram MUST contain
exactly one LTP segment or four zero octets as a keep-alive. LTP
MUST perform segmentation in such a way as to ensure that every LTP
segment fits into a single packet which will not require IP
fragmentation as discussed above.
3.3.1. DCCP
The DCCP transport for LTP SHOULD use the IANA assigned port 1113/
DCCP and service code 7107696; the use of other port numbers and
service codes is implementation specific.
3.3.2. UDP
The UDP transport for LTP SHOULD use the IANA assigned port 1113/UDP;
the use of other port numbers is implementation specific.
3.4. Keep Alive Option
It may be desirable for a UDP or DCCP CL or transport to send "keep-
alive" packets during extended idle periods. This may be needed to
refresh a contact table entry at the destination, or to maintain an
address mapping in a NAT or a dynamic access rule in a firewall.
Therefore, the CL or transport MAY send a datagram containing exactly
4 octets of zero bits. The CL or transport receiving such a packet
MUST discard this packet; the receiving CL or transport may then
perform local maintenance of its state tables, these maintenance
functions are not covered in this draft. Note that packets carrying
Bundles or segments will always contain more than 4 octets of
information (either the Bundle or the LTP header); keep-alive packets
will therefore never be mistaken for actual data packets. If UDP or
DCCP are being used for communication in both directions between a
pair of Bundle agents, transmission and processing of keep-alives in
the two directions occurs independently. Keep-alive intervals SHOULD
be configurable, SHOULD default to 15 sec, and MUST NOT be configured
shorter than 15 sec.
3.5. Checksums
Both the core Bundle protocol specification and core LTP
specification assume that they are transmitting over an erasure
Kruse, et al. Expires August 5, 2013 [Page 6]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
channel, i.e. a channel that either delivers packets correctly or not
at all.
3.5.1. DCCP
A DCCP transmitter MUST, therefore, ensure that the entire packet is
checksummed by setting the Checksum Coverage to 0. Likewise, the
DCCP receiver MUST ignore all packets with partial checksum coverage.
3.5.2. UDP
A UDP transmitter therefore MUST NOT disable UDP checksums, and the
UDP receiver MUST NOT disable checking of received UDP checksums.
Even when UDP checksums are enabled a small probability of UDP packet
corruption remains. In some environments it may be acceptable for
LTP or the Bundle protocol to occasionally receive corrupted input.
In general, however, a UDP implementation SHOULD use optional
security extensions available in the Bundle protocol or LTP to
protect against message corruption.
3.6. DCCP Congestion Control Modules
DCCP supports pluggable congestion control modules in order to
optimize its behavior to particular environments. The two most
common congestion control modules (CCIDs) are TCP-like Congestion
Control (CCID2) [RFC4341] and TCP-Friendly Rate Control (CCID3)
[RFC4342]. TCP-like Congestion Control is designed to emulate TCP's
congestion control as much as possible. It is recommended for
applications that want to send data as quickly as possible, while
TCP-Friendly Rate Control is aimed at applications that want to avoid
sudden changes in sending rate. DTN use cases seem to fit more into
the first case so DCCP CL's and transports SHOULD use TCP-like
Congestion Control (CCID2) by default.
4. IANA Considerations
Port number assignments 1113/UDP and 4556/UDP have been registered
with IANA. Assigned port numbers are 1113/DCCP for the transport of
LTP, and 4556/DCCP for the transport of Bundles. Assigned DCCP
Service Codes are 7107696 for tunneling LTP and 1685351985 for
tunneling Bundle Protocol.
5. Security Considerations
This memo describes the use of datagrams to transport DTN application
Kruse, et al. Expires August 5, 2013 [Page 7]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
data. Hosts may be in the position of having to accept and process
packets from unknown sources; the DTN Endpoint ID can be discovered
only after the Bundle has been retrieved from the DCCP or UDP packet.
Hosts SHOULD use authentication methods available in the DTN
specifications to prevent malicious hosts from inserting unknown data
into the application.
Hosts need to listen for and process DCCP or UDP data on the known
LTP or Bundle protocol ports. A denial of service scenario exists
where a malicious host sends datagrams at a high rate, forcing the
receiving hosts to use their resources to process and attempt to
authenticate this data. Whenever possible, hosts SHOULD use IP
address filtering to limit the origin of packets to known hosts.
6. References
6.1. Normative References
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791,
September 1981.
[RFC1883] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 1883, December 1995.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2147] Borman, D., "TCP and UDP over IPv6 Jumbograms", RFC 2147,
May 1997.
[RFC2675] Borman, D., Deering, S., and R. Hinden, "IPv6 Jumbograms",
RFC 2675, August 1999.
[RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram
Congestion Control Protocol (DCCP)", RFC 4340, March 2006.
[RFC4341] Floyd, S. and E. Kohler, "Profile for Datagram Congestion
Control Protocol (DCCP) Congestion Control ID 2: TCP-like
Congestion Control", RFC 4341, March 2006.
[RFC5050] Scott, K. and S. Burleigh, "Bundle Protocol
Specification", RFC 5050, November 2007.
[RFC5325] Burleigh, S., Ramadas, M., and S. Farrell, "Licklider
Transmission Protocol - Motivation", RFC 5325,
September 2008.
Kruse, et al. Expires August 5, 2013 [Page 8]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
[RFC5326] Ramadas, M., Burleigh, S., and S. Farrell, "Licklider
Transmission Protocol - Specification", RFC 5326,
September 2008.
[RFC5327] Farrell, S., Ramadas, M., and S. Burleigh, "Licklider
Transmission Protocol - Security Extensions", RFC 5327,
September 2008.
6.2. Informative References
[I-D.irtf-dtnrg-tcp-clayer]
Demmer, M., Ott, J., and S. Perreault, "Delay Tolerant
Networking TCP Convergence Layer Protocol",
draft-irtf-dtnrg-tcp-clayer-05 (work in progress),
January 2013.
[Kent88] Kent, C. and J. Mogul, "Fragmentation considered
harmful.", 1988, <http://doi.acm.org/10.1145/55482.55524>.
[RFC1191] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191,
November 1990.
[RFC1981] McCann, J., Deering, S., and J. Mogul, "Path MTU Discovery
for IP version 6", RFC 1981, August 1996.
[RFC2309] Braden, B., Clark, D., Crowcroft, J., Davie, B., Deering,
S., Estrin, D., Floyd, S., Jacobson, V., Minshall, G.,
Partridge, C., Peterson, L., Ramakrishnan, K., Shenker,
S., Wroclawski, J., and L. Zhang, "Recommendations on
Queue Management and Congestion Avoidance in the
Internet", RFC 2309, April 1998.
[RFC2914] Floyd, S., "Congestion Control Principles", BCP 41,
RFC 2914, September 2000.
[RFC2923] Lahey, K., "TCP Problems with Path MTU Discovery",
RFC 2923, September 2000.
[RFC4342] Floyd, S., Kohler, E., and J. Padhye, "Profile for
Datagram Congestion Control Protocol (DCCP) Congestion
Control ID 3: TCP-Friendly Rate Control (TFRC)", RFC 4342,
March 2006.
[RFC4821] Mathis, M. and J. Heffner, "Packetization Layer Path MTU
Discovery", RFC 4821, March 2007.
[RFC5405] Eggert, L. and G. Fairhurst, "Unicast UDP Usage Guidelines
for Application Designers", BCP 145, RFC 5405,
Kruse, et al. Expires August 5, 2013 [Page 9]
Internet-Draft Internet Datagram Transport for DTN Feb 2013
November 2008.
Authors' Addresses
Hans Kruse
Ohio University
292 Lindley Hall
Athens, OH 45701
United States
Phone: +1 740 593 4891
Email: kruse@ohiou.edu
Samuel Jero
Ohio University
Athens, Ohio 45701
United States
Email: sj323707@ohio.edu
Shawn Ostermann
Ohio University
Stocker Engineering Center
Athens, OH 45701
United States
Phone: +1 740 593 1566
Email: ostermann@eecs.ohiou.edu
Kruse, et al. Expires August 5, 2013 [Page 10]