PCE Working Group                                                A. Wang
Internet-Draft                                             China Telecom
Intended status: Standards Track                             B. Khasanov
Expires: April 23, 2021                                          S. Fang
                                                                  R. Tan
                                             Huawei Technologies,Co.,Ltd
                                                                  C. Zhu
                                                         ZTE Corporation
                                                        October 20, 2020


                  PCEP Extension for Native IP Network
               draft-ietf-pce-pcep-extension-native-ip-09

Abstract

   This document defines the Path Computation Element Communication
   Protocol (PCEP) extension for Central Control Dynamic Routing (CCDR)
   based application in Native IP network.  The scenario and framework
   of CCDR in native IP is described in [RFC8735] and
   [I-D.ietf-teas-pce-native-ip].  This draft describes the key
   information that is transferred between Path Computation Element
   (PCE) and Path Computation Clients (PCC) to accomplish the End to End
   (E2E) traffic assurance in Native IP network under central control
   mode.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 23, 2021.

Copyright Notice

   Copyright (c) 2020 IETF Trust and the persons identified as the
   document authors.  All rights reserved.




Wang, et al.             Expires April 23, 2021                 [Page 1]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Conventions used in this document . . . . . . . . . . . . . .   3
   3.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   3
   4.  Capability Advertisemnt . . . . . . . . . . . . . . . . . . .   3
     4.1.  Open message  . . . . . . . . . . . . . . . . . . . . . .   3
   5.  PCEP messages . . . . . . . . . . . . . . . . . . . . . . . .   4
     5.1.  The PCInitiate message  . . . . . . . . . . . . . . . . .   4
     5.2.  The PCRpt message . . . . . . . . . . . . . . . . . . . .   5
   6.  PCECC Native IP TE Procedures . . . . . . . . . . . . . . . .   6
     6.1.  BGP Session Establishment Procedures  . . . . . . . . . .   6
     6.2.  Explicit Route Establish Procedures . . . . . . . . . . .   9
     6.3.  BGP Prefix Advertisement Procedures . . . . . . . . . . .  12
   7.  New PCEP Objects  . . . . . . . . . . . . . . . . . . . . . .  13
     7.1.  CCI Object  . . . . . . . . . . . . . . . . . . . . . . .  13
     7.2.  BGP Peer Info Object  . . . . . . . . . . . . . . . . . .  14
     7.3.  Explicit Peer Route Object  . . . . . . . . . . . . . . .  17
     7.4.  Peer Prefix Association Object  . . . . . . . . . . . . .  18
   8.  New Error-Types and Error-Values Defined  . . . . . . . . . .  19
   9.  Management Consideration  . . . . . . . . . . . . . . . . . .  20
   10. Security Considerations . . . . . . . . . . . . . . . . . . .  21
   11. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  21
     11.1.  PCEP Object Types  . . . . . . . . . . . . . . . . . . .  21
   12. Contributor . . . . . . . . . . . . . . . . . . . . . . . . .  21
   13. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . .  21
   14. Normative References  . . . . . . . . . . . . . . . . . . . .  22
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  23

1.  Introduction

   Generally, Multiprotocol Label Switching Traffic Engineering (MPLS-
   TE) requires the corresponding network devices support Multiprotocol
   Label Switching (MPLS) or Resource ReSerVation Protocol (RSVP)/Label
   Distribution Protocol (LDP) technologies to assure the End-to-End
   (E2E) traffic performance.  But in native IP network, there will be
   no such signaling protocol to synchronize the action among different
   network devices.  It is necessary to use the central control mode



Wang, et al.             Expires April 23, 2021                 [Page 2]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   that described in [RFC8283] to correlate the forwarding behavior
   among different network devices.  Draft [I-D.ietf-teas-pce-native-ip]
   describes the architecture and solution philosophy for the E2E
   traffic assurance in Native IP network via Multi Border Gateway
   Protocol (BGP) solution.  This draft describes the corresponding Path
   Computation Element Communication Protocol (PCEP) extensions to
   transfer the key information about BGP peer info, peer prefix
   association and the explicit peer route on on-path routers.

2.  Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

3.  Terminology

   This document uses the following terms defined in [RFC5440]: PCE,
   PCEP

   The following terms are defined in this document:

   o  CCDR: Central Control Dynamic Routing

   o  E2E: End to End

   o  BPI: BGP Peer Info

   o  EPR: Explicit Peer Route

   o  PPA: Peer Prefix Association

   o  QoS: Quality of Service

4.  Capability Advertisemnt

4.1.  Open message

   During the PCEP Initialization Phase, PCEP Speakers (PCE or PCC)
   advertise their support of Native IP extensions.

   This document defines a new Path Setup Type (PST) [RFC8408] for
   Native-IP, as follows:

   o  PST = TBD1: Path is a Native IP path as per
      [I-D.ietf-teas-pce-native-ip].



Wang, et al.             Expires April 23, 2021                 [Page 3]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   A PCEP speaker MUST indicate its support of the function described in
   this document by sending a PATH-SETUP-TYPE-CAPABILITY TLV in the OPEN
   object with this new PST included in the PST list.

   [I-D.ietf-pce-pcep-extension-for-pce-controller] defined the PCECC-
   CAPABILITY sub-TLV to exchange information about their PCECC
   capability.  A new flag is defined in PCECC-CAPABILITY sub-TLV for
   Native IP.

   N (NATIVE-IP-TE-CAPABILITY - 1 bit - TBD2): If set to 1 by a PCEP
   speaker, it indicates that the PCEP speaker is capable for TE in
   Native IP network as specified in this document.  The flag MUST be
   set by both the PCC and PCE in order to support this extension.

5.  PCEP messages

   PCECC Native IP TE solution utilizing the existing PCE LSP Initate
   Request message(PCInitiate)[RFC8281], and PCE Report message(PCRpt)
   [RFC8281] to accomplish the multi BGP sessions establishment, end to
   end TE path deployment, and route prefixes advertisement among
   different BGP sessions.  A new PST for Native-IP is used to indicate
   the path setup based on TE in Native IP networks.

   The extended PCInitiate message described in
   [I-D.ietf-pce-pcep-extension-for-pce-controller] is used to download
   or cleanup central controller's instructions (CCIs).
   [I-D.ietf-pce-pcep-extension-for-pce-controller] specify an object
   called CCI for the encoding of central controller's instructions.
   This document specify a new CCI object-type for Native IP.  The PCEP
   messages are extended in this document to handle the PCECC operations
   for Native IP.  Three new PCEP Objects (BGP Peer Info (BPI) Object,
   Explicit Peer Route (EPR) Object and Peer Prefix Association (PPA)
   Object) are defined in this document.  Refer toSection 7 for detail
   object definitions.

5.1.  The PCInitiate message

   The PCInitiate Message defined in [RFC8281] and extended in
   [I-D.ietf-pce-pcep-extension-for-pce-controller] is further extended
   to support Native-IP CCI.

   The format of the extended PCInitiate message is as follows:









Wang, et al.             Expires April 23, 2021                 [Page 4]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


        <PCInitiate Message> ::= <Common Header>
                                 <PCE-initiated-lsp-list>
     Where:
        <Common Header> is defined in [RFC5440]

        <PCE-initiated-lsp-list> ::= <PCE-initiated-lsp-request>
                                     [<PCE-initiated-lsp-list>]

        <PCE-initiated-lsp-request> ::=
                             (<PCE-initiated-lsp-instantiation>|
                              <PCE-initiated-lsp-deletion>|
                              <PCE-initiated-lsp-central-control>)

        <PCE-initiated-lsp-central-control> ::= <SRP>
                                                (<LSP>
                                                <cci-list>)|
                                                ((<BPI>|<EPR>|<PPA>)
                                                <CCI>)

        <cci-list> ::=  <CCI>
                        [<cci-list>]

     Where:
         <cci-list> is as per
         [I-D.ietf-pce-pcep-extension-for-pce-controller].
         <PCE-initiated-lsp-instantiation> and
         <PCE-initiated-lsp-deletion> are as per
         [RFC8281].

        The LSP and SRP object is defined in [RFC8231].

   When PCInitiate message is used create Native IP instructions, the
   SRP and CCI objects MUST be present.  The error handling for missing
   SRP or CCI object is as per
   [I-D.ietf-pce-pcep-extension-for-pce-controller].  Further either one
   of BPI, EPR, or PPA object MUST be present.  If none of them are
   present, the receiving PCC MUST send a PCErr message with Error-
   type=6 (Mandatory Object missing) and Error-value=TBD (Native IP
   object missing).

   To cleanup the SRP object must set the R (remove) bit.

5.2.  The PCRpt message

   The PCRpt message is used to acknowledge the Native-IP instructions
   received from the central controller (PCE).

   The format of the PCRpt message is as follows:



Wang, et al.             Expires April 23, 2021                 [Page 5]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


         <PCRpt Message> ::= <Common Header>
                             <state-report-list>
      Where:

         <state-report-list> ::= <state-report>[<state-report-list>]

         <state-report> ::= (<lsp-state-report>|
                             <central-control-report>)

         <lsp-state-report> ::= [<SRP>]
                                <LSP>
                                <path>

         <central-control-report> ::= [<SRP>]
                                      (<LSP>
                                      <cci-list>)|
                                      ((<BPI>|<EPR>|<PPA>)
                                      <CCI>)


       Where:
         <path> is as per [RFC8231] and the LSP and SRP object are
         also defined in [RFC8231].

   The error handling for missing CCI object is as per
   [I-D.ietf-pce-pcep-extension-for-pce-controller].  Further either one
   of BPI, EPR, or PPA object MUST be present.  If none of them are
   present, the receiving PCE MUST send a PCErr message with Error-
   type=6 (Mandatory Object missing) and Error-value=TBD ( Native IP
   object missing).

6.  PCECC Native IP TE Procedures

   The detail procedures for the TE in native IP environment are
   described in the following sections.

6.1.  BGP Session Establishment Procedures

   The procedures for establishing the BGP session between two peers is
   shown below, using the PCInitiate and PCRpt message pair.

   The PCInitiate message should be sent to PCC which acts as BGP
   routers and route reflector.  In the example in Figure 1, it should
   be sent to R1(M1), R3(M2 & M3) and R7(M4), when R3 acts as RR.

   When PCC receives the BPI and CCI object (with the R bit set to 0 in
   SRP object) in PCInitiate message, the PCC should try to establish
   the BGP session with the indicated Peer AS and Local/Peer IP address.



Wang, et al.             Expires April 23, 2021                 [Page 6]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   When PCC creates successfully the BGP session that is indicated by
   the associated information, it should report the result via the PCRpt
   messages, with BPI object included, and the corresponding SRP and CCI
   object.

   When PCC receives this message with the R bit set to 1 in SRP object
   in PCInitiate message, the PCC should clear the BGP session that
   indicated by the BPI object.

   When PCC clears successfully the specified BGP session, it should
   report the result via the PCRpt message, with the BPI object
   included, and the corresponding SRP and CCI object.







































Wang, et al.             Expires April 23, 2021                 [Page 7]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


 M2   PCInitiate Message:                           M3   PCInitiate Message:
      CC-ID=X3(Symbolic Path Name=Class A)               CC-ID=X3(Symbolic Path Name=Class A)
      BPI Object(Local IP=R3_A, Peer IP=R1_A)            BPI Object(Local IP=R3_A, Peer IP=R7_A)

M2-R PCRpt Message:                                 M3-R PCRpt Message:
      CC-ID=X3                                           CC-ID=X3
      BPI Object(Local IP=R3_A, Peer IP=R1_A)            BPI Object(Local IP=R3_A, Peer IP=R7_A)
                     ^                                                       ^
                     |                                                       |
                     +------------------------------------^------------------+
                                                          |
                                                          |
                                                          |
                                                          |    +------------------+
 M1    PCInitiate Message:                          +----------+       PCE        +-----------+
       CC-ID=X1(Symbolic Path Name=Class A)         |     |    +--------^---------+           |
       BPI Object(Local IP=R1_A, Peer IP=R3_A)      |     |             |                     |
                                                    |     |             |                     |
                                             <------+     +-------------+                     +---+
 M1-R PCRpt Message:                                |                   |                     |   |
      CC-ID=X1                                      |                  +v-+                   |   |
      BPI Object(Local IP=R1_A, Peer IP=R3_A        +------------------+R3+-------------------+   |                                                                                  )
                                                    |                  +--+                   |   |
                                                    |                                         |   |
                                                   +v-+          +--+          +--+         +-v+  |
                                                   |R1+----------+R5+----------+R6+---------+R7|  |
                                                   ++-+          +--+          +--+         +-++  |
M4  PCInitiate Message:                             |                                         |   |
    CC-ID=X7(Symbolic Path Name=Class A)            |                                         |   |
    BPI Object(Local IP=R7_A,Peer IP=R3_A)          |            +--+          +--+           |   |
                                                    +------------+R2+----------+R4+-----------+   |
                                                                                                  |
M4-R PCRpt Message:                                                                               |
      CC-ID=X7                               <----------------------------------------------------+
      BPI Object(Local IP=R3_A, Peer IP=R1_A)


                         Figure 1: BGP Session Establishment Procedures(R3 act as RR)

   If the PCC cannot establish the BGP session that required by this
   object, it should report the error values with the newly defined
   error type(Error-type=TBD) and error value(Error-Value=01 or 02),
   which is indicated in Section 8








Wang, et al.             Expires April 23, 2021                 [Page 8]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


6.2.  Explicit Route Establish Procedures

   The detail procedures for the explicit route establishment procedures
   is shown below, using PCInitiate and PCRpt message pair.

   The PCInitiate message should be sent to the on-path routers
   respectively.  In the example, for explicit route from R1 to R7, the
   PCInitiate message should be sent to R1(M1), R2(M2) and R4(M3), as
   shown in Figure 2.  For explicit route from R7 to R1, the PCInitiate
   message should be sent to R7(M1), R4(M2) and R2(M3), as shown in
   Figure 3..

   When PCC receives the EPR and the CCI object (with the R bit set to 0
   in SRP object) in PCInitiate message, the PCC should install the
   explicit route to the the peer.

   When PCC install successfully the explicit route to the peer, it
   should report the result via the PCRpt messages, with EPR object
   included, and the corresponding SRP and CCI object.

   When PCC receives the EPR and the CCI object with the R bit set to 1
   in SRP object in PCInitiate message, the PCC should clear the
   explicit route to the peer that indicated by the EPR object.

   When PCC clear successfully the explicit route that indicated by this
   object, it should report the result via the PCRpt message, with the
   EPR object included, and the corresponding SRP and CCI object.
























Wang, et al.             Expires April 23, 2021                 [Page 9]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


                                                              +------------------+
M1    PCInitiate Message:                          +----------+       PCE        +-----------+
      CC-ID=X1(Symbolic Path Name=Class A)         |          +----^---^---^-----+           |
      EPR Object(Peer Address=R7_A                 |               |   |   |                 |
                 Next Hop=R2_A)                    |               |   |   |                 |
                                                   |               |   |   |                 |
M1-R PCRpt Message:                <---------------+               |   |   |                 |
     CC-ID=X1                                      |               |  +v-+ |                 |
     EPR Object(Peer Address=R7_A                  +------------+ +---+R3+-------------------+                                                                                       )
                Next Hop=R2_A)                     |               |  +--+ |                 |
                                                   |               |       |                 |
                                                  +v-+      +--+   |       |       +--+    +-v+
                                                  |R1+------+R5++ +----------------+R6+----+R7|
                                                  ++-+      +--+   |       |       +--+    +-++
                                                   |               |       |                 |
M2  PCInitiate Message                             |           +---+       +---+             |
    CC-ID=X2(Symbolic Path Name=Class A)           |          +v-+ |       |  +v-+           |
    EPR Object(Peer Address=R7_A                   +----------+R2+-+ +--------+R4+-----------+
               Next Hop=R4_A)                                      |       |
                                                                   |       |
M2-R PCRpt Message                                                 |       |
     CC-ID=X2(Symbolic Path Name=Class A)   <----------------------+       |
     EPR Object(Peer Address=R7_A                                          |
                Next Hop=R4_A)                                             |
                                                                           v
                                                    M3   PCInitiate Message
                                                         CC-ID=X4(Symbolic Path Name=Class A)
                                                         EPR Object(Peer Address=R7_A
                                                                    Next Hop=R7_A)

                                                    M3-R PCRpt Message
                                                         CC-ID=X4(Symbolic Path Name=Class A)
                                                         EPR Object(Peer Address=R7_A
                                                                    Next Hop=R7_A)

                      Figure 2: Explicit Route Establish Procedures(From R1 to R7)















Wang, et al.             Expires April 23, 2021                [Page 10]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


              -------------------------------------------------------------------------+
              |                                                                        |
              v                                               +------------------+     |
M1    PCInitiate Message:                          +----------+       PCE        +-----+-----+
      CC-ID=X7(Symbolic Path Name=Class A)         |          +----^---^---^-----+           |
      EPR Object(Peer Address=R1_A                 |               |   |   |                 |
                 Next Hop=R4_A)                    |               |   |   |                 |
                                                   |               |   |   |                 |
M1-R PCRpt Message:                                |               |   |   |                 |
     CC-ID=X7                                      |               |  +v-+ |                 |
     EPR Object(Peer Address=R1_A                  +------------+ +---+R3+-------------------+                                                                                       )
                Next Hop=R4_A)                     |               |  +--+ |                 |
                                                   |               |       |                 |
                                                  +v-+      +--+   |       |       +--+    +-v+
                                                  |R1+------+R5++ +----------------+R6+----+R7|
                                                  ++-+      +--+   |       |       +--+    +-++
                                                   |               |       |                 |
M3  PCInitiate Message                             |           +---+       +---+             |
    CC-ID=X2(Symbolic Path Name=Class A)           |          +v-+ |       |  +v-+           |
    EPR Object(Peer Address=R1_A                   +----------+R2+-+ +--------+R4+-----------+
               Next Hop=R1_A)                                      |       |
                                                                   |       |
M3-R PCRpt Message                                                 |       |
     CC-ID=X2(Symbolic Path Name=Class A)   <----------------------+       |
     EPR Object(Peer Address=R1_A                                          |
                Next Hop=R1_A)                                             |
                                                                           v
                                                    M2   PCInitiate Message
                                                         CC-ID=X4(Symbolic Path Name=Class A)
                                                         EPR Object(Peer Address=R1_A
                                                                    Next Hop=R2_A)

                                                    M2-R PCRpt Message
                                                         CC-ID=X4(Symbolic Path Name=Class A)
                                                         EPR Object(Peer Address=R1_A
                                                                    Next Hop=R2_A)

                     Figure 3: Explicit Route Establish Procedures(From R7 to R1)

   Upon the error occurs, the PCC SHOULD send the corresponding
   error(Error-type=TBD, Error-value=03) information that defined in
   Section 8.  When the peer info that associated with the Symbolic Path
   Name is not the same as the peer info that indicated in EPR object in
   PCC, an error (Error-type=TBD, Error-value=04) should be reported via
   the PCRpt message.






Wang, et al.             Expires April 23, 2021                [Page 11]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


6.3.  BGP Prefix Advertisement Procedures

   The detail procedures for BGP prefix advertisement is shown below,
   using PCInitiate and PCRpt message pair.

   The PCInitiate message should be sent to PCC that acts as BGP peer
   router only.  In the example, it should be sent to R1(M1) and R7(M2)
   respectively.

   When PCC receives the PPA and the CCI object (with the R bit set to 0
   in SRP object) in PCInitiate message, the PCC should send the
   prefixes indicated in this object to the appointed BGP peer.

   When PCC sends successfully the prefixes to the appointed BGP peer,
   it should report the result via the PCRpt messages, with PPA object
   included, and the corresponding SRP and CCI object.

   When PCC receives the PPA and the CCI object with the R bit set to 1
   in SRP object in PCInitiate message, the PCC should withdraw the
   prefixes advertisement to the peer that indicated by this object.

   When PCC withdraws successfully the prefixes that indicated by this
   object, it should report the result via the PCRpt message, with the
   PPA object included, and the corresponding SRP and CCI object.

   The IPv4 prefix MUST only be advertised via the IPv4 BGP session and
   the IPv6 prefix MUST only be advertised via the IPv6 BGP session.  If
   mismatch occur, an error(Error-type=TBD, Error-value=05) should be
   reported.

   When the peer info that associated with the Symbolic Path Name is not
   the same as the peer info that indicated in PPA object in PCC, an
   error (Error-type=TBD, Error-value=06) should be reported via the
   PCRpt message.

















Wang, et al.             Expires April 23, 2021                [Page 12]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


                                                M2  PCInitiate Message:
                                                    CC-ID=X7(Symbolic Path Name=Class A)
                                                    PPA Object(Peer IP=R1_A, Prefix=7_A)

                                                                                           <-----+
                                                M2-R  PCRpt Message:                             |
                                                      CC-ID=X7                                   |
                                                      PPA Object(Peer IP=R1_A, Prefix=7_A)       |
                                                                                                 |
                                                                                                 |
                                                                                                 |
                                                              +------------------+               |
M1   PCInitiate Message:                           +----------+       PCE        +-----------+   |
     CC-ID=X1(Symbolic Path Name=Class A)          |          +------------------+           |   |
     PPA Object(Peer IP=R7_A, Prefix=1_A)          |                                         |   |
                                                   |                                         |   |
                                        <----------+                                         +---+
M1-R PCRpt Message:                                |                                         |
     CC-ID=X1                                      |                  +--+                   |
     PPA Object(Peer IP=R7_A,Prefix=1_A)           +------------------+R3+-------------------+                                                                                        )
                                                   |                  +--+                   |
                                                   |                                         |
                                                  +v-+          +--+          +--+         +-v+
                                                  |R1+----------+R5+----------+R6+---------+R7|
                                                  ++-+          +--+          +--+         +-++
                                                   |                                         |
                                                   |                                         |
                                                   |            +--+          +--+           |
                                                   +------------+R2+----------+R4+-----------+

                                       Figure 4: BGP Prefix Advertisement Procedures

7.  New PCEP Objects

   One new CCI Object and three new PCEP objects are defined in this
   draft.  All new PCEP objects are as per [RFC5440]

7.1.  CCI Object

   The Central Control Instructions (CCI) Object is used by the PCE to
   specify the forwarding instructions is defined in
   [I-D.ietf-pce-pcep-extension-for-pce-controller].  This document
   defines another object-type for Native-IP.

   CCI Object-Type is TBD for Native-IP as below






Wang, et al.             Expires April 23, 2021                [Page 13]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                            CC-ID                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |          Reserved             |             Flags             |
   +---------------------------------------------------------------+
   |                                                               |
   //                        Optional TLV                         //
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

           Figure 5: CCI Object for Native IP

                                 Figure 1

   The field CC-ID is as described in
   [I-D.ietf-pce-pcep-extension-for-pce-controller].  Following fields
   are defined for CCI Object-Type TBD

   Reserved:  is set to zero while sending, ignored on receipt.

   Flags:  is used to carry any additional information pertaining to the
      CCI.  Currently no flag bits are defined.

   The Symbolic Path Name TLV [RFC8231] MUST be included in the CCI
   Object-Type TBD to identify the end to end TE path in Native IP
   environment and MUST be unique.

7.2.  BGP Peer Info Object

   The BGP Peer Info object is used to specify the information about the
   peer that the PCC should establish the BGP relationship with.  This
   object should only be included and sent to the head and end router of
   the E2E path in case there is no Route Reflection (RR) involved.  If
   the RR is used between the head and end routers, then such
   information should be sent to head router, RR and end router
   respectively.

   By default, there MUST be no prefix be distributed via such BGP
   session that established by this object.

   By default, the Local/Peer IP address SHOULD be dedicated to the
   usage of native IP TE solution, and SHOULD NOT be used by other BGP
   sessions that established by manual or non PCE initiated
   configuration.

   BGP Peer Info Object-Class is TBD



Wang, et al.             Expires April 23, 2021                [Page 14]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   BGP Peer Info Object-Type is 1 for IPv4 and 2 for IPv6

   The format of the BGP Peer Info object body for IPv4(Object-Type=1)
   is as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Peer AS Number                           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   ETTL        |              Reserved                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    Local IP Address                           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                   Peer IP Address                             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Additional TLVs                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
        Figure 6: BGP Peer Info Object Body Format for IPv4

   The format of the BGP Peer Info object body for IPv6(Object-Type=2)
   is as follows:





























Wang, et al.             Expires April 23, 2021                [Page 15]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      Peer AS Number                           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |   ETTL        |              Reserved                         |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |               Local IP Address (16 bytes)                     |
   +                                                               +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |               Peer IP Address (16 bytes)                      |
   +                                                               +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Additional TLVs                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
         Figure 7: BGP Peer Info Object Body Format for IPv6

   Peer AS Number: 4 Bytes, to indicate the AS number of Remote Peer.

   ETTL: 1 Bytes, to indicate the multi hop count for EBGP session.  It
   should be 0 and ignored when Local AS and Peer AS is same.

   Reserved: is set to zero while sending, ignored on receipt..

   Local IP Address(4/16 Bytes): IP address of the local router, used to
   peer with other end router.  When Object-Type is 1, length is 4
   bytes; when Object-Type is 2, length is 16 bytes.

   Peer IP Address(4/16 Bytes): IP address of the peer router, used to
   peer with the local router.  When Object-Type is 1, length is 4
   bytes; when Object-Type is 2, length is 16 bytes;

   Additional TLVs: TLVs that associated with this object, can be used
   to convey other necessary information for dynamic BGP session
   establishment.  Its definition is out of the current document.






Wang, et al.             Expires April 23, 2021                [Page 16]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


7.3.  Explicit Peer Route Object

   The Explicit Peer Route object is defined to specify the explicit
   peer route to the corresponding peer address on each device that is
   on the E2E assurance path.  This Object should be sent to all the
   devices that locates on the E2E assurance path that calculated by
   PCE.

   The path established by this object should have higher priority than
   other path calculated by dynamic IGP protocol, but should be lower
   priority that the static route configured by manual or NETCONF
   channel.

   Explicit Peer Route Object-Class is TBD.

   Explicit Peer Route Object-Type is 1 for IPv4 and 2 for IPv6

   The format of Explicit Peer Route object body for IPv4(Object-Type=1)
   is as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Route Priority        |          Reserved               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                IPv4 Peer Address                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |           Next Hop Address to the IPv4 Peer Address           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       Figure 8: Explicit Peer Route Object Body Format for IPv4

   The format of Explicit Peer Route object body for IPv6(Object-Type=2)
   is as follows:


















Wang, et al.             Expires April 23, 2021                [Page 17]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |       Route Priority        |           Reserved              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |                      IPv6 Peer Address                        |
   +                                                               +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   +                                                               +
   |          Next Hop Address to the IPv6 Peer Address            |
   +                                                               +
   |                                                               |
   +                                                               +
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       Figure 9: Explicit Peer Route Object Body Format for IPv6

   Route Priority: 2 Bytes, The priority of this explicit route.  The
   higher priority should be preferred by the device.

   Reserved.: is set to zero while sending, ignored on receipt.

   Peer Address: To indicate the peer address.

   Next Hop Address to the Peer: To indicate the next hop address to the
   corresponding peer.

7.4.  Peer Prefix Association Object

   The Peer Prefix Association object is defined to specify the IP
   prefixes that should be advertised to the corresponding peer.  This
   object should only be included and sent to the head/end router of the
   end2end path.

   The prefixes information included in this object MUST only be
   advertised to the indicated peer, MUST NOT be advertised to other BGP
   peers.

   Peer Prefix Association Object-Class is TBD

   Peer Prefix Association Object-Type is 1 for IPv4 and 2 for IPv6




Wang, et al.             Expires April 23, 2021                [Page 18]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   The format of the Peer Prefix Association object body is as follows:

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Peer IPv4 Address                            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   //               IPv4 Prefix subobjects                         //
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     Figure 10: Peer Prefix Association Object Body Format for IPv4

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                  Peer IPv6 Address                            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                               |
   //               IPv6 Prefix subobjects                         //
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      Figure 11: Peer Prefix Association Object Body Format for IPv6

   Peer IPv4 Address: 4 Bytes.  Identifies the peer IPv4 address that
   the associated prefixes will be sent to.

   IPv4 Prefix subojects: List of IPv4 Prefix subobjects that defined in
   [RFC3209], identify the prefixes that will be sent to the peer that
   identified by Peer IPv4 Address List.

   Peer IPv6 Address: 16 Bytes.  Identifies the peer IPv6 address that
   the associated prefixes will be sent to.

   IPv6 Prefix subojects: List of IPv6 Prefix subobjects that defined in
   [RFC3209], identify the prefixes that will be sent to the peer that
   identified by Peer IPv6 Address List.

8.  New Error-Types and Error-Values Defined

   A PCEP-ERROR object is used to report a PCEP error and is
   characterized by an Error-Type that specifies that type of error and
   an Error-value that provides additional information about the error.
   An additional Error-Type and several Error-values are defined to
   represent some the errors related to the newly defined objects, which
   are related to Native IP TE procedures.





Wang, et al.             Expires April 23, 2021                [Page 19]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


          +============+===============+==============================+
          | Error-Type | Meaning       | Error-value                  |
          +============+===============+==============================+
          | TBD        | Native IP     |                              |
          |            | TE failure    |                              |
          +------------+---------------+------------------------------+
          |            |               | 0: Unassigned                |
          +------------+---------------+------------------------------+
          |            |               | 1: Peer AS not match         |
          +------------+---------------+------------------------------+
          |            |               | 2: Peer IP can't be reached  |
          +------------+---------------+------------------------------+
          |            |               | 3: Explicit Peer Route Error |
          +------------+---------------+------------------------------+
          |            |               | 4: EPR/BPI Peer Info mismatch|
          +------------+---------------+------------------------------+
          |            |               | 5: BPI/PPA Object AF mismatch|
          +------------+---------------+------------------------------+
          |            |               | 6: PPA/BPI Peer Info mismatch|
          +------------+---------------+------------------------------+
          |            |               | 7:                           |
          +------------+---------------+------------------------------+
          |            |               | 8:                           |
          +------------+---------------+------------------------------+
          |            |               | 8:                           |
          +------------+---------------+------------------------------+
          |            |               | 9:                           |
          +------------+---------------+------------------------------+
               Figure 12: Newly defined Error-Type and Error-Value

9.  Management Consideration

   The information transferred in this draft is mainly used for the
   light weight BGP session setup, explicit route deployment and the
   prefix distribution.  The planning, allocation and distribution of
   the peer addresses within IGP should be accomplished in advanced and
   they are out of the scope of this draft.

   [RFC8232] describes the state synchronization procedure between
   stateful PCE and PCC.  The communication of PCE and PCC described in
   this draft should also follow this procedures, treat the three newly
   defined objects that associated with the same symbolic path name as
   the attribute of the same path in the LSP-DB.

   When PCE detects one or some of the PCCs are out of control, it
   should recompute and redeploy the traffic engineering path for native
   IP on the active PCCs.  When PCC detects that it is out of control of
   the PCE, it should clear the information that initiated by the PCE.



Wang, et al.             Expires April 23, 2021                [Page 20]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   The PCE should assures the avoidance of possible transient loop in
   such node failure when it deploy the explicit peer route on the PCCs.

10.  Security Considerations

   Service provider should consider the protection of PCE and their
   communication with the underlay devices, which is described in
   document [RFC5440] and [RFC8253]

11.  IANA Considerations

11.1.  PCEP Object Types

   IANA is requested to allocate new registry for the PCEP Object Type:

   Object-Class Value       Name                        Reference
   TBD               CCI Object                      This document
                     Object-Type
                        TBD: Native IP

   TBD               BGP Peer Info                   This document
                     Object-Type
                        1: IPv4 address
                        2: IPv6 address

   TBD               Explicit Peer Route             This document
                     Object-Type
                        1: IPv4 address
                        2: IPv6 address

   TBD               Peer Prefix Association         This document
                     Object-Type
                        1: IPv4 address
                        2: IPv6 address

12.  Contributor

   Dhruv Dhody has contributed the contents of this draft.

13.  Acknowledgement

   Thanks Mike Koldychev, Siva Sivabalan, Adam Simpson for his valuable
   suggestions and comments.








Wang, et al.             Expires April 23, 2021                [Page 21]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


14.  Normative References

   [I-D.ietf-pce-pcep-extension-for-pce-controller]
              Li, Z., Peng, S., Negi, M., Zhao, Q., and C. Zhou, "PCEP
              Procedures and Protocol Extensions for Using PCE as a
              Central Controller (PCECC) of LSPs", draft-ietf-pce-pcep-
              extension-for-pce-controller-07 (work in progress),
              September 2020.

   [I-D.ietf-teas-pce-native-ip]
              Wang, A., Khasanov, B., Zhao, Q., and H. Chen, "PCE in
              Native IP Network", draft-ietf-teas-pce-native-ip-11 (work
              in progress), August 2020.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC3209]  Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
              and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
              Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
              <https://www.rfc-editor.org/info/rfc3209>.

   [RFC5440]  Vasseur, JP., Ed. and JL. Le Roux, Ed., "Path Computation
              Element (PCE) Communication Protocol (PCEP)", RFC 5440,
              DOI 10.17487/RFC5440, March 2009,
              <https://www.rfc-editor.org/info/rfc5440>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8231]  Crabbe, E., Minei, I., Medved, J., and R. Varga, "Path
              Computation Element Communication Protocol (PCEP)
              Extensions for Stateful PCE", RFC 8231,
              DOI 10.17487/RFC8231, September 2017,
              <https://www.rfc-editor.org/info/rfc8231>.

   [RFC8232]  Crabbe, E., Minei, I., Medved, J., Varga, R., Zhang, X.,
              and D. Dhody, "Optimizations of Label Switched Path State
              Synchronization Procedures for a Stateful PCE", RFC 8232,
              DOI 10.17487/RFC8232, September 2017,
              <https://www.rfc-editor.org/info/rfc8232>.







Wang, et al.             Expires April 23, 2021                [Page 22]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   [RFC8253]  Lopez, D., Gonzalez de Dios, O., Wu, Q., and D. Dhody,
              "PCEPS: Usage of TLS to Provide a Secure Transport for the
              Path Computation Element Communication Protocol (PCEP)",
              RFC 8253, DOI 10.17487/RFC8253, October 2017,
              <https://www.rfc-editor.org/info/rfc8253>.

   [RFC8281]  Crabbe, E., Minei, I., Sivabalan, S., and R. Varga, "Path
              Computation Element Communication Protocol (PCEP)
              Extensions for PCE-Initiated LSP Setup in a Stateful PCE
              Model", RFC 8281, DOI 10.17487/RFC8281, December 2017,
              <https://www.rfc-editor.org/info/rfc8281>.

   [RFC8283]  Farrel, A., Ed., Zhao, Q., Ed., Li, Z., and C. Zhou, "An
              Architecture for Use of PCE and the PCE Communication
              Protocol (PCEP) in a Network with Central Control",
              RFC 8283, DOI 10.17487/RFC8283, December 2017,
              <https://www.rfc-editor.org/info/rfc8283>.

   [RFC8408]  Sivabalan, S., Tantsura, J., Minei, I., Varga, R., and J.
              Hardwick, "Conveying Path Setup Type in PCE Communication
              Protocol (PCEP) Messages", RFC 8408, DOI 10.17487/RFC8408,
              July 2018, <https://www.rfc-editor.org/info/rfc8408>.

   [RFC8735]  Wang, A., Huang, X., Kou, C., Li, Z., and P. Mi,
              "Scenarios and Simulation Results of PCE in a Native IP
              Network", RFC 8735, DOI 10.17487/RFC8735, February 2020,
              <https://www.rfc-editor.org/info/rfc8735>.

Authors' Addresses

   Aijun Wang
   China Telecom
   Beiqijia Town, Changping District
   Beijing, Beijing  102209
   China

   Email: wangaj3@chinatelecom.cn


   Boris Khasanov
   Huawei Technologies,Co.,Ltd
   Moskovskiy Prospekt 97A
   St.Petersburg  196084
   Russia

   Email: bhassanov@yahoo.com





Wang, et al.             Expires April 23, 2021                [Page 23]


Internet-Draft    PCEP Extension for Native IP Network      October 2020


   Sheng Fang
   Huawei Technologies,Co.,Ltd
   Huawei Bld., No.156 Beiqing Rd.
   Beijing
   China

   Email: fsheng@huawei.com


   Ren Tan
   Huawei Technologies,Co.,Ltd
   Huawei Bld., No.156 Beiqing Rd.
   Beijing
   China

   Email: tanren@huawei.com


   Chun Zhu
   ZTE Corporation
   50 Software Avenue, Yuhua District
   Nanjing, Jiangsu  210012
   China

   Email: zhu.chun1@zte.com.cn


























Wang, et al.             Expires April 23, 2021                [Page 24]