Network Working Group                                  Y. Jiang, Ed.
Internet Draft                                                Y. Luo
Intended status: Standards Track                              Huawei
                                                    E. Mallette, Ed.
                                               Bright House Networks
C. Shen                                                      Y. Shen
China Telecom                                       Juniper Networks
W. Cheng                                                     G. Zhou
China Mobile                                            China Unicom
Expires: July 2016                                   January 5, 2016


       Multi-chassis Passive Optical Network (PON) Protection in MPLS
                       draft-ietf-pals-mc-pon-02.txt


Abstract

   MPLS is being deployed deeper into operator networks, often to or
   past the access network node. Separately network access nodes such
   as Passive Optical Network (PON) Optical Line Terminations (OLTs)
   have evolved to support first-mile access protection, where one or
   more physical OLTs provide first-mile diversity to the customer edge.
   Multi-homing support is needed on the MPLS-enabled PON OLT to
   provide resiliency for provided services.  This document describes
   the multi-chassis PON protection architecture in MPLS and also
   specifies the Inter-Chassis Communication Protocol (ICCP) extension
   to support it.

Status of this Memo

   This Internet-Draft is submitted to IETF in full conformance with
   the provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six
   months and may be updated, replaced, or obsoleted by other documents
   at any time.  It is inappropriate to use Internet-Drafts as
   reference material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html




Jiang, et al            Expires July 5, 2016               [Page 1]


Internet-Draft            MC-PON Protection             January 2016


   This Internet-Draft will expire on July 5, 2016.

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors. All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with
   respect to this document. Code Components extracted from this
   document must include Simplified BSD License text as described in
   Section 4.e of the Trust Legal Provisions and are provided without
   warranty as described in the Simplified BSD License.

Table of Contents

   1.   Conventions used in this document ......................... 3
   2.   Terminology ............................................... 3
   3.   Introduction .............................................. 3
   4.   ICCP Protocol Extensions .................................. 6
      4.1. Multi-chassis PON Application TLVs ..................... 6
      4.1.1.  PON Connect TLV ..................................... 6
      4.1.2.  PON Disconnect TLV .................................. 7
      4.1.3.  PON Configuration TLV ............................... 8
      4.1.4.  PON State TLV ....................................... 9
      4.1.5.  PON ONU Database Sync TLV ........................... 9
   5.   PON ONU Database Synchronization ......................... 11
   6.   Multi-chassis PON application procedures ................. 11
      6.1. Protection procedure upon PON link failures ........... 13
      6.2. Protection procedure upon PW failures ................. 13
      6.3. Protection procedure upon the working OLT failure ..... 14
   7.   Security Considerations .................................. 14
   8.   IANA Considerations ...................................... 14
   9.   References ............................................... 14
      9.1. Normative References .................................. 14
      9.2. Informative References ................................ 15
   10.  Acknowledgments .......................................... 15
   Authors' Addresses ............................................ 16








Jiang, et al            Expires July 5, 2016               [Page 2]


Internet-Draft            MC-PON Protection             January 2016


1. Conventions used in this document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2. Terminology

   DSL  Digital Subscriber Line

   FTTx  Fiber-to-the-x (FTTx, x = H for home, P for premises, C for
   curb)

   ICCP  Inter-Chassis Communication Protocol

   OLT  Optical Line Termination

   ONU  Optical Network Unit

   MPLS  Multi-Protocol Label Switching

   PON  Passive Optical Network

   RG   Redundancy Group

3. Introduction

   Multi-Protocol Label Switching (MPLS) is being extended to the edge
   of operator networks, as is described in the seamless MPLS use cases
   [SEAMLESS-MPLS], and the Multi-Segment Pseudowires with Passive
   Optical Network (PON) access use case [RFC6456]. Combining MPLS with
   Optical Line Termination (OLT) access further facilitates a low cost
   multi-service convergence.

   Tens of millions of Fiber-to-the-x (FTTx, x = H for home, P for
   premises, C for curb) lines have been deployed over the years, with
   many of those lines being some PON variant. PON provides operators a
   cost-effective solution for delivering high bandwidth (1Gbps or even
   10Gbps) to a dozen or more subscribers simultaneously.

   In the past, access technologies such as PON and Digital Subscriber
   Line (DSL) are usually used for subscribers, and no redundancy is
   provided in their deployment.






Jiang, et al            Expires July 5, 2016               [Page 3]


Internet-Draft            MC-PON Protection             January 2016


   But with the rapid growth of mobile data traffic, more and more Long
   Term Evolution (LTE) small cells and Wi-Fi hotspots are deployed.
   PON is considered as a viable low cost backhaul solution for these
   mobile services. Besides its high bandwidth and scalability, PON
   further provides synchronization features, e.g., SyncE [G.8261] and
   IEEE 1588v2 [IEEE-1588] functionality, which can fulfill
   synchronization needs of mobile backhaul services.

   The Broadband Forum specifies reference architecture for mobile
   backhaul network using MPLS transport in [TR-221] where PON can be
   the access technology, and is further working on PON-based mobile
   backhaul network architecture in [WT-331].

   Unlike typical residential service where a single or handful of end-
   users hangs off of a single PON OLT port in a physical optical
   distribution network, a PON port that supports a dozen LTE small
   cells or Wi-Fi hotspots could be providing service to hundreds of
   simultaneous subscribers. Small cell backhaul often demands the
   economics of a PON first-mile and yet expects first-mile protection
   commonly available in point-to-point access portfolio.

   Some optical layer of protection mechanisms, such as Trunk and Tree
   protection, are specified in [IEEE-1904.1] to avoid single point of
   failure in the access. They are called Type B and Type C protection
   respectively in [G983.1].

   Trunk protection architecture is an economical PON resiliency
   mechanism, where the working OLT and the working link between the
   working splitter port and the working OLT (i.e., the working trunk
   fiber) is protected by a redundant protection OLT and a redundant
   trunk fiber between the protection splitter port and the protection
   OLT, however it only protects a portion of the optical path from OLT
   to Optical Network Units (ONUs). This is different from the more
   complex and costly Type C protection architecture where there is a
   working optical distribution network path from the working OLT and a
   complete protected optical distribution network path from the
   protection OLT to the ONUs. Figure 1 demonstrates a typical scenario
   of Trunk protection.










Jiang, et al            Expires July 5, 2016               [Page 4]


Internet-Draft            MC-PON Protection             January 2016


                        |                                 |
                        |<--Optical Distribution Network->|
                        |                                 |
                        |   branch               trunk    +-----+
                  +-----+   fibers               fibers   |     |
   Base     ------|     |     |                    |      . OLT |
   Stations ------| ONU |\    |                    |   ,'`|  A  |
            ------|     |  \  V                    V -`   +-----+
                  +-----+    \                    .'
                            .  \  +----------+ ,-`
                  +-----+   .    \|          -`   Working
   Base     ------|     |   .     | Optical  |
   Stations ------| ONU |---------| Splitter |
            ------|     |   .    /|          -,   Protection
                  +-----+   .  /  +----------+ `'.,
                             /                     `-,    +-----+
                  +-----+  /                          `'.,|     |
   Base     ------|     |/                                | OLT |
   Stations ------| ONU |                                 |  B  |
            ------|     |                                 +-----+
                  +-----+
               Figure 1 Trunk Protection Architecture in PON

   Besides small cell backhaul, this protection architecture can also
   be applicable to other services, for example, Digital Subscriber
   Line (DSL) and Multi-System Operator (MSO) services. In that case,
   an ONU in Figure 1 can play the similar role as a Digital Subscriber
   Line Access Multiplexer (DSLAM) and dozens of Customer Premises
   Equipments (CPEs) or cable modems may be attached to it.

   In some deployments, it is also possible that only some ONUs are
   needed to be protected.

   The PON architecture as depicted in Figure 1 can provide redundancy
   in its physical topology, however, all traffic including link
   Operation Administration and Maintenance (OAM) are blocked on the
   protection link which frustrates end to end protection mechanisms
   such as those specified in ITU-T G.8031 [G.8031]. Therefore, some
   standard signaling mechanisms are needed between OLTs to exchange
   information, for example, PON link status, registered ONU
   information, and network status, so that protection and restoration
   can be done rapidly and reliably, especially when the OLTs also
   support MPLS.






Jiang, et al            Expires July 5, 2016               [Page 5]


Internet-Draft            MC-PON Protection             January 2016


   Inter-Chassis Communication Protocol (ICCP) [ICCP] provides a
   framework for inter-chassis synchronization of state and
   configuration data between a set of two or more Provider Edges (PEs).
   Currently ICCP only defines application specific messages for
   Pseudowire (PW) redundancy and mLACP, but it can be easily extended
   to support PON as an Attachment Circuit (AC) redundancy.

   This document proposes the extension of ICCP to support Multi-
   chassis PON protection in MPLS.



4. ICCP Protocol Extensions

4.1. Multi-chassis PON Application TLVs

   A set of multi-chassis PON application Type-Length-Values (TLVs) are
   defined in the following sub-sections.

4.1.1. PON Connect TLV

   This TLV is included in the Redundancy Group (RG) Connect message to
   signal the establishment of PON application connection.

   0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |U|F|   Type=0x00XX             |    Length                     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Protocol Version         |A|         Reserved            |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    Optional Sub-TLVs                          |
   ~                                                               ~
   |                                                               |
   +                                 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |             ...                 |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   - U and F Bits, both are set to 0.

   - Type, set to 0x00XX for "PON Connect TLV".

   - Length, Length of the TLV in octets excluding the U-bit, F-bit,
   Type, and Length fields.

   - Protocol Version, the version of this PON specific protocol for
   the purposes of inter-chassis communication. This is set to 0x0001.



Jiang, et al            Expires July 5, 2016               [Page 6]


Internet-Draft            MC-PON Protection             January 2016


   - A Bit, Acknowledgement Bit. MUST be set to 1 if the sender has
   received a PON Connect TLV from the recipient. Otherwise, set to 0.

   - Reserved, Reserved for future use, and MUST be set to zero.

   - Optional Sub-TLVs, there are no optional Sub-TLVs defined for this
   version of the protocol.

4.1.2. PON Disconnect TLV

   This TLV is included in the RG Disconnect message to indicate that
   the connection for the PON application is to be terminated.

   0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |U|F|   Type=0x00XX             |    Length                     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                       Optional Sub-TLVs                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   - U and F Bits, both are set to 0.

   - Type, set to 0x00XX for "PON Disconnect TLV".

   - Length, Length of the TLV in octets excluding the U-bit, F-bit,
   Type, and Length fields.

   - Optional Sub-TLVs, there are no optional Sub-TLVs defined for this
   version of the protocol.

















Jiang, et al            Expires July 5, 2016               [Page 7]


Internet-Draft            MC-PON Protection             January 2016


4.1.3. PON System Configuration TLV

   The "PON System Configuration TLV" is included in the "RG
   Application Data" message, and announces an OLT's system parameters
   to other members in the same RG.
   0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |U|F|   Type=0x00XX             |    Length                     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                         System ID                             |
   |                                                              |
   |                                                              |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     System Priority           |             Port ID           |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   - U and F Bits, both are set to 0.

   - Type, set to 0x00XX for "PON System Configuration TLV".

   - Length, Length of the TLV in octets excluding the U-bit, F-bit,
   Type, and Length fields.

   - System ID, 8 octets encoding the System ID used by the OLT, which
   is the Chassis MAC address. If a 6 octet System ID is used, the
   least significant 2 octets of the 8 octet field will be encoded as
   0000.

   - System Priority, 2 octets encoding the System Priority.

   - Port ID, 2 octets PON Port ID.

   Further configuration such as multicast table and ARP table for
   static MAC addresses may be defined as separate configuration TLVs.












Jiang, et al            Expires July 5, 2016               [Page 8]


Internet-Draft            MC-PON Protection             January 2016


4.1.4.PON State TLV

   The "PON State TLV" is included in the "RG Application Data" message,
   and used by an OLT to report its PON states to other members in the
   same RG.

   0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |U|F|   Type=0x00XX             |    Length                     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                              ROID                             |
   |                                                               |
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    Local PON Port state                       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                    Remote PON Port state                      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   - U and F Bits, both are set to 0.

   - Type, set to 0x00XX for "PON State TLV"

   - Length, Length of the TLV in octets excluding the U-bit, F-bit,
   Type, and Length fields.

   - ROID, Redundant Object ID (ROID) as defined in Section 4.3 of
   [ICCP].

   - Local PON Port State, the status of the local PON port as
   determined by the sending OLT (PE). The last bit is defined as Fault
   indication of the PON Port associated with this PW (1 - in fault; 0
   - in normal).

   - Remote PON Port State, the status of the remote PON port as
   determined by the remote peer of the sending OLT (i.e., the sending
   PE). The last bit is defined as Fault indication of the PON Port
   associated with this PW (1 - in fault; 0 - in normal).

4.1.5.PON ONU Database Sync TLV

   This TLV is used to communicate the registered ONU database
   associated with a PON port between the active and standby OLT. This
   message is used to both transmit the PON ONU Database from working



Jiang, et al            Expires July 5, 2016               [Page 9]


Internet-Draft            MC-PON Protection             January 2016


   OLT to protect OLT and to communicate the PON ONU database status
   between protect OLT and working OLT.

   0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |U|F|   Type=0x00XX             |    Length                     |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                            ROID                               |
   |                                                               |
   |                                                               |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |A|  Reserved   |                      OUI                      |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-|
   |                     ONU Database Entry1                       |
   ~                                                               ~
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+


   - U and F Bits, both are set to 0.

   - Type, set to 0x00XX for "PON ONU Database Sync TLV"

   - Length, Length of the TLV in octets excluding the U-bit, F-bit,
   Type, and Length fields.

   - ROID, as defined in Section 4.3 of [ICCP].

   - A bit, Acknowledgement bit. Set to 1 if the receiver has received
   a PON ONU Database Sync. Otherwise, set to 0.

   - Reserved, reserved for future use and MUST be set to zero.

   - OUI, the 3-byte [IEEE-802] organization unique identifier that
   uniquely identifies the format for describing the registered ONU
   database information. There are multiple PON standards and are
   varying implementations within a given PON standard which likely
   have different required information, format, etc., related to the
   ONU Database Entry.

   - ONU Database Entry, there may be one or more ONU Database Entries
   transmitted in the PON ONU Database Sync TLV, each of which would
   describe a registered ONU. The format of the ONU Database Entry is
   outside the scope of this document and will be defined by the
   relevant PON standard organization.




Jiang, et al            Expires July 5, 2016              [Page 10]


Internet-Draft            MC-PON Protection             January 2016


5. PON ONU Database Synchronization

   Without an effective mechanism to communicate the registered ONUs
   between the working and protection OLT, all registered ONUs would be
   de-registered and go through re-registration during a switchover,
   which would significantly increase protection time. To enable faster
   switchover capability, the work OLT must be able to communicate the
   registered ONUs associated with an ROID to the protection OLT.

   The PON ONU Database Synchronization would begin once the ICCP PON
   Application enters OPERATIONAL state. The working OLT, the one with
   the working link member for the ROID, would begin transmitting the
   database of actively registered ONUs to the protection OLT for the
   same ROID. Each instance of the PON ONU Database Sync TLV describes
   a set of ONU Database Entries. Each ONU Database Entry would
   describe a registered ONU.

   The transmission of PON ONU Database Descriptors for a given ROID is
   only unidirectional - from the working OLT to the protection OLT.
   The protection OLT would only be responsible for acknowledging the
   received message to provide a reliable database synchronization
   mechanism. As ONUs register and deregister from the working OLT, the
   working OLT would transmit PON ONU Database Synchronization TLV
   including only the updated ONU Database Entries.

   If protected ONUs and unprotected ONUs are miscellaneously attached
   to the same splitter, only the protected ONUs needs to be
   synchronized. The specific ONUs which needs to be synchronized can
   be policy driven and provisioned in the management plane, or by some
   other signaling options.


6. Multi-chassis PON application procedures

   Two typical MPLS protection network architectures for PON access are
   depicted in Fig.2 and Fig.3 (their PON access segments are the same
   as in Fig.1 and thus omitted for simplification). OLTs with MPLS
   functionality are connected to a single PE (Fig.2) or dual home PEs
   (Fig.3) respectively, i.e., the working OLT to PE1 by a working PW
   and the protection OLT to PE1 or PE2 by a protection PW, thus these
   devices constitute an MPLS network which provides PW transport
   services between ONUs and a Customer Edge (CE), and the PWs can
   provide protection for each other.






Jiang, et al            Expires July 5, 2016              [Page 11]


Internet-Draft            MC-PON Protection             January 2016


                  +-----+
                  |     |
                  |OLT  -,
                  | A   | `.,
                  +-----+    ', PW1
                               `',
                                  `.,   +-----+          +-----+
                                     ', |     |          |     |
                                       `. PE1 ------------  CE |
                                     .'`|     |          |     |
                                  ,-`   +-----+          +-----+
                                .`
                  +-----+    .'` PW2
                  |     | ,-`
                  |OLT  -`
                  | B   |
                  +-----+
                 Figure 2 An MPLS Network with a Single PE


                  +-----+               +-----+
                  |     |     PW1       |     |
                  |OLT  ----------------- PE1 -,
                  | A   |               |     | ',
                  +-----+               +--/--+   ',
                                           |        `.
                                           |          `. +-----+
                                           |            `'     |
                                           |             |  CE |
                                           |             .     |
                                           |           ,'+-----+
                                           |        ,-`
                  +-----+               +--\--+   ,'
                  |     |     PW2       |     | .`
                  |OLT  ----------------- PE2 -`
                  | B   |               |     |
                  +-----+               +-----+
               Figure 3 An MPLS Network with Dual-homing PEs


   Faults may be encountered in PON access links, or in the MPLS
   network (including the working OLT). Procedures for these cases are
   described in this section (it is assumed that both OLTs and PEs are
   working in the independent mode of PW redundancy [RFC6870]).





Jiang, et al            Expires July 5, 2016              [Page 12]


Internet-Draft            MC-PON Protection             January 2016


6.1. Protection procedure upon PON link failures

   When a fault is detected on a working PON link, a working OLT
   switches to the corresponding protection PON link attached with its
   protection OLT, i.e., the working OLT turns off its faulty PON
   interface so that the protection trunk link to its protection OLT
   can be activated. The working OLT then MUST send an LDP fault
   notification message (i.e., with the status bit "Local AC (ingress)
   Receive Fault" being set) to its peer PE on the remote end of the PW.
   At the same time, the working OLT MUST send an ICCP message with PON
   State TLV with local PON Port State being set to notify the
   protection OLT of the PON fault.

   Upon receiving a PON state TLV where Local PON Port state is set, a
   protection OLT MUST activate the protection PON link in the
   protection group, and advertise a notification message for the
   protection PW with the Preferential Forwarding status bit of active
   to the remote PE.

   According to [RFC6870], the remote PE(s) can match the local and
   remote Preferential Forwarding status and select PW2 as the new
   active PW over which data traffic is sent.



6.2. Protection procedure upon PW failures

   Usually MPLS networks have its own protection mechanism such as LSP
   protection or Fast Reroute (FRR). But in a link sparse access or
   aggregation network where protection for a PW is impossible in its
   LSP layer, the following PW layer protection procedures can be
   enabled.

   When a fault is detected on its working PW (e.g., by VCCV BFD), a
   working OLT SHOULD turn off its associated PON interface and then
   send an ICCP message with PON State TLV with local PON Port State
   being set to notify the protection OLT of the PON fault.

   Upon receiving a PON state TLV where Local PON Port state is set,
   the protection OLT MUST activate its PON interface to the protection
   trunk fiber. At the same time, the protection OLT MUST send a
   notification message for the protection PW with the Preferential
   Forwarding status bit of active to the remote PE, so that traffic
   can be switched to the protection PW.





Jiang, et al            Expires July 5, 2016              [Page 13]


Internet-Draft            MC-PON Protection             January 2016


6.3. Protection procedure upon the working OLT failure

   As depicted in Fig. 2, a service is provisioned with a working PW
   and a protection PW, both PW terminated on PE1. If PE1 lost its
   connection to the working OLT, it SHOULD send an LDP notification
   message on the protection PW with the Request Switchover bit set.

   Upon receiving an LDP notification message from its remote PE with
   the Request Switchover bit set, a protection OLT MUST activate its
   optical interface to the protection trunk fiber and activate the
   associated protection PW, so that traffic can be reliably switched
   to the protection trunk PON link and the protection PW.

   In the case of Fig.3, PW-RED State TLV as described in Section 7.1
   of [ICCP] can be used by PE1 to notify PE2 the faults in all the
   scenarios, and PE2 operates the same as described in Section 5.1 to
   5.3.



7. Security Considerations

   Security considerations as described in [ICCP] apply.

8. IANA Considerations

   These values are requested from the registry of "ICC RG parameter
   type":
   0x00X0         PON Connect TLV
   0x00X1         PON Disconnect TLV
   0x00X2         PON Configuration TLV
   0x00X3         PON State TLV
   0x00X4         PON ONU Database Sync TLV

9. References

9.1.  Normative References

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
             Requirement Levels", BCP 14, RFC 2119, March 1997

   [RFC6870] Muley, P., Aissaoui, M., "Pseudowire Preferential
             Forwarding Status Bit", RFC 6870, February 2013

   [ICCP] Martini, L. and et al, "Inter-Chassis Communication Protocol
             for L2VPN PE Redundancy", RFC 7275, June 2014



Jiang, et al            Expires July 5, 2016              [Page 14]


Internet-Draft            MC-PON Protection             January 2016


9.2. Informative References

   [RFC6456] Li, H., Zheng, R., and Farrel, A., "Multi-Segment
             Pseudowires in Passive Optical Networks", RFC 6456,
             November 2011

   [SEAMLESS-MPLS] Leymann, N., Decraene, B., Filsfils, C.,
             Konstantynowicz, M., and Steinberg, D., "Seamless MPLS
             Architecture", draft-ietf-mpls-seamless-mpls-07, Work in
             progress

   [G983.1] ITU-T, "Broadband optical access systems based on Passive
             Optical Networks (PON)", ITU-T G.983.1, January, 2005

   [G.8031] ITU-T, "Ethernet Linear Protection Switching", ITU-T G.8031,
             January, 2015

   [G.8261] ITU-T, "Timing and synchronization aspects in packet
             networks", ITU-T G.8261, August, 2013

   [IEEE-1588] IEEE Std. 1588, "IEEE Standard for a Precision Clock
             Synchronization Protocol for Networked Measurement and
             Control Systems", IEEE Instrumentation and Measurement
             Society, July, 2008

   [IEEE-1904.1] IEEE Std. 1904.1, "Standard for Service
             Interoperability in Ethernet Passive Optical Networks
             (SIEPON)", IEEE Computer Society, June, 2013

   [IEEE-802] IEEE Std. 802, "IEEE Standard for Local and Metropolitan
             Area Networks: Overview and Architecture", IEEE Computer
             Society, March, 2002

   [TR-221] BBF TR-221, "Technical Specifications for MPLS in Mobile
             Backhaul Networks", the Broadband Forum, October, 2011

   [WT-331] BBF WT-331, "Architecture and Technical Requirements for
             PON-Based Mobile Backhaul Networks", the Broadband Forum,
             Work in progress

10.  Acknowledgments

   The authors would like to thank Min Ye, Hongyu Li, Wei Lin, Xifeng
   Wan, Yannick Legoff and Shrinivas Joshi for their valuable
   discussions and comments.




Jiang, et al            Expires July 5, 2016              [Page 15]


Internet-Draft            MC-PON Protection             January 2016


Authors' Addresses

   Yuanlong Jiang
   Huawei Technologies Co., Ltd.
   Bantian, Longgang district
   Shenzhen 518129, China
   Email: jiangyuanlong@huawei.com

   Yong Luo
   Huawei Technologies Co., Ltd.
   Bantian, Longgang district
   Shenzhen 518129, China
   Email: dennis.luoyong@huawei.com

   Edwin Mallette
   Bright House Networks
   4145 S. Falkenburg Road
   Tampa, FL 33578 USA
   Email: edwin.mallette@gmail.com

   Chengbin Shen
   China Telecom
   1835 South Pudong Road
   Shanghai 200122, China
   Email: shencb@sttri.com.cn

   Yimin Shen
   Juniper Networks
   10 Technology Park Drive
   Westford, MA 01886, USA
   Email: yshen@juniper.net

   Weiqiang Cheng
   China Mobile
   No.32 Xuanwumen West Street
   Beijing 100053, China
   Email: chengweiqiang@chinamobile.com

   Guangtao Zhou
   China Unicom
   No.9 Shouti South Road
   Beijing 100048, China
   Email: zhouguangtao@chinaunicom.cn






Jiang, et al            Expires July 5, 2016              [Page 16]