MMUSIC                                                       C. Holmberg
Internet-Draft                                                 S. Loreto
Intended status: Standards Track                            G. Camarillo
Expires: June 8, 2015                                           Ericsson
                                                        December 5, 2014


Stream Control Transmission Protocol (SCTP)-Based Media Transport in the
                   Session Description Protocol (SDP)
                     draft-ietf-mmusic-sctp-sdp-09

Abstract

   SCTP (Stream Control Transmission Protocol) is a transport protocol
   used to establish associations between two endpoints.

   This specification describes how to describe SCTP associations using
   the Session Description Protocol (SDP), and defines the following new
   SDP Media Description protocol identifiers (proto values):'SCTP',
   'SCTP/DTLS' and 'DTLS/SCTP'.

   The specification also describes how to use the new proto values
   together with the SDP Offer/Answer mechanism in order to negotiate
   and establish SCTP associations, and how to indicate the SCTP
   application usage.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on June 8, 2015.

Copyright Notice

   Copyright (c) 2014 IETF Trust and the persons identified as the
   document authors.  All rights reserved.




Holmberg, et al.          Expires June 8, 2015                  [Page 1]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   4
   3.  SCTP Terminology  . . . . . . . . . . . . . . . . . . . . . .   4
   4.  SDP Media Descriptions  . . . . . . . . . . . . . . . . . . .   4
     4.1.  General . . . . . . . . . . . . . . . . . . . . . . . . .   4
     4.2.  Protocol Identifiers  . . . . . . . . . . . . . . . . . .   5
     4.3.  Media Format Management . . . . . . . . . . . . . . . . .   5
     4.4.  Syntax  . . . . . . . . . . . . . . . . . . . . . . . . .   6
     4.5.  Example . . . . . . . . . . . . . . . . . . . . . . . . .   6
   5.  SDP 'sctp-port' Attribute . . . . . . . . . . . . . . . . . .   6
     5.1.  General . . . . . . . . . . . . . . . . . . . . . . . . .   6
     5.2.  Syntax  . . . . . . . . . . . . . . . . . . . . . . . . .   7
   6.  SDP 'max-message-size' Attribute  . . . . . . . . . . . . . .   7
     6.1.  General . . . . . . . . . . . . . . . . . . . . . . . . .   7
     6.2.  Syntax  . . . . . . . . . . . . . . . . . . . . . . . . .   7
   7.  SDP 'fmtp' Attribute  . . . . . . . . . . . . . . . . . . . .   7
     7.1.  General . . . . . . . . . . . . . . . . . . . . . . . . .   7
     7.2.  Syntax  . . . . . . . . . . . . . . . . . . . . . . . . .   8
   8.  SCTP Association Management . . . . . . . . . . . . . . . . .   8
     8.1.  General . . . . . . . . . . . . . . . . . . . . . . . . .   8
     8.2.  SDP sendrecv/sendonly/sendrecv/inactive Attribute . . . .   8
     8.3.  SDP setup Attribute . . . . . . . . . . . . . . . . . . .   8
       8.3.1.  General . . . . . . . . . . . . . . . . . . . . . . .   8
       8.3.2.  SCTP Association Initiation . . . . . . . . . . . . .   9
       8.3.3.  TLS Role Determination  . . . . . . . . . . . . . . .   9
     8.4.  SDP connection Attribute  . . . . . . . . . . . . . . . .   9
   9.  SDP Offer/Answer Procedures . . . . . . . . . . . . . . . . .  10
     9.1.  General . . . . . . . . . . . . . . . . . . . . . . . . .  10
     9.2.  Generating the Initial SDP Offer  . . . . . . . . . . . .  11
     9.3.  Generating the SDP Answer . . . . . . . . . . . . . . . .  11
     9.4.  Offerer Processing of the SDP Answer  . . . . . . . . . .  12
     9.5.  Modifying the Session . . . . . . . . . . . . . . . . . .  12
   10. Multihoming Considerations  . . . . . . . . . . . . . . . . .  13
   11. NAT Considerations  . . . . . . . . . . . . . . . . . . . . .  13
     11.1.  General  . . . . . . . . . . . . . . . . . . . . . . . .  13
     11.2.  ICE Considerations . . . . . . . . . . . . . . . . . . .  13



Holmberg, et al.          Expires June 8, 2015                  [Page 2]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   12. Examples  . . . . . . . . . . . . . . . . . . . . . . . . . .  14
   13. Security Considerations . . . . . . . . . . . . . . . . . . .  14
   14. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  14
     14.1.  New SDP proto values . . . . . . . . . . . . . . . . . .  14
     14.2.  New SDP Attribute  . . . . . . . . . . . . . . . . . . .  14
     14.3.  association-usage Name Registry  . . . . . . . . . . . .  15
   15. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  16
   16. Change Log  . . . . . . . . . . . . . . . . . . . . . . . . .  16
   17. References  . . . . . . . . . . . . . . . . . . . . . . . . .  16
     17.1.  Normative References . . . . . . . . . . . . . . . . . .  16
     17.2.  Informative References . . . . . . . . . . . . . . . . .  17
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  18

1.  Introduction

   SDP (Session Description Protocol) [RFC4566] provides a general-
   purpose format for describing multimedia sessions in announcements or
   invitations.  TCP-Based Media Transport in the Session Description
   Protocol (SDP) [RFC4145] specifies a general mechanism for describing
   and establishing TCP (Transmission Control Protocol) [RFC5246]
   streams.  Connection-Oriented Media Transport over the Transport
   Layer Security (TLS) Protocol in the Session Description Protocol
   (SDP) [RFC4572] extends RFC4145 [RFC4145] for describing TCP-based
   media streams that are protected using TLS.

   SCTP (Stream Control Transmission Protocol) is a transport protocol
   used to establish associations between two endpoints.

   This specification describes how to describe SCTP associations using
   the Session Description Protocol (SDP) [RFC4566], and defines the
   following new SDP Media Description [RFC4566] protocol identifiers
   (proto values):'SCTP', 'SCTP/DTLS' and 'DTLS/SCTP'.

   The specification also describes how to use the new proto values
   together with the SDP Offer/Answer mechanism [RFC3264] in order to
   negotiate and establish SCTP associations, and how to indicate the
   SCTP application usage.

   NOTE: TLS is designed to run on top of a byte-stream oriented
   transport protocol providing a reliable, in-sequence delivery like
   TCP.  [RFC6083] presents serious limitations with transporting SCTP
   on top of TLS.  Therefore, defining a mechanism to negotiate media
   streams transported using SCTP on top of TLS is outside the scope of
   this specification.







Holmberg, et al.          Expires June 8, 2015                  [Page 3]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


2.  Terminology

   In this document, the key words "MUST", "MUST NOT", "REQUIRED",
   "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT
   RECOMMENDED", "MAY", and "OPTIONAL" are to be interpreted as
   described in BCP 14, RFC 2119 [RFC2119] and indicate requirement
   levels for compliant implementations.

3.  SCTP Terminology

   SCTP Association: A protocol relationship between SCTP endpoints,
   composed of the two SCTP endpoints and protocol state information
   including Verification Tags and the currently active set of
   Transmission Sequence Numbers (TSNs), etc.  An association can be
   uniquely identified by the transport addresses used by the endpoints
   in the association.  Two SCTP endpoints MUST NOT have more than one
   SCTP association between them at any given time.

   SCTP Stream: A unidirectional logical channel established from one to
   another associated SCTP endpoint, within which all user messages are
   delivered in sequence except for those submitted to the unordered
   delivery service.

   SCTP Transport address: A transport address is traditionally defined
   by a network-layer address, a transport-layer protocol, and a
   transport-layer port number.  In the case of SCTP running over IP, a
   transport address is defined by the combination of an IP address and
   an SCTP port number (where SCTP is the transport protocol).

4.  SDP Media Descriptions

4.1.  General

   This section defines the following new SDP Media Description (m-
   line) protocol identifiers (proto values) for describing an SCTP
   association: 'SCTP', 'SCTP/DTLS' and 'DTLS/SCTP'.  The section also
   describes how an m- line, associated with the proto values, is
   created.

   The following is the format for an 'm' line, as specified in RFC4566
   [RFC4566]:

       m=<media> <port> <proto> <fmt> ...

   The 'SCTP', 'SCTP/DTLS' and 'DTLS/SCTP' proto values are similar to
   both the 'UDP' and 'TCP' proto values in that they only describe the
   transport protocol and not the upper-layer protocol.




Holmberg, et al.          Expires June 8, 2015                  [Page 4]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   NOTE: When the 'DTLS/SCTP' proto value is used, the underlying
   transport protocol is either UDP or TCP.

   The m- line fmt value, identifying the application-layer protocol,
   MUST be registered by IANA.

4.2.  Protocol Identifiers

   The new proto values are defined as below:

   o  The 'SCTP' proto value describes an SCTP association, as defined
      in [RFC4960].

   o  The 'SCTP/DTLS' proto value describes a Datagram Transport Layer
      Security (DTLS) [RFC6347] connection on top of an SCTP
      association, as defined in [RFC6083].

   o  The 'DTLS/SCTP' proto value describes an SCTP association on top
      of a DTLS connection, as defined in
      [I-D.ietf-tsvwg-sctp-dtls-encaps].

   NOTE: In the case of 'DTLS/SCTP', the actual transport protocol below
   DTLS is either UDP or TCP.

   OPEN ISSUE #1: It is FFS whether separate proto values will be used,
   depending on whether the underlying transport protocol is UDP (e.g.
   'UDP/DTLS/SCTP') or TCP (e.g.  'TCP/DTLS/SCTP').

4.3.  Media Format Management

   [RFC4566] defines that specifications defining new proto values must
   define the rules by which their media format (fmt) namespace is
   managed.  Use of an existing MIME subtype for the format is
   encouraged.  If no MIME subtype exists, it is recommended that a
   suitable one is registered through the IETF process [RFC6838]
   [RFC4289] by production of, or reference to, a standards-track RFC
   that defines the transport protocol for the format.

   An m- line with a proto value of 'SCTP', 'SCTP/DTLS' or 'DTLS/SCTP'
   always describe a single SCTP association.

   In addition, such m- line MUST further indicate the application-layer
   protocol using an 'fmt' identifier.  There MUST be exactly one 'fmt'
   value per m- line associated with the proto values defined in this
   specification.  The "fmt" namespace associated with those proto
   values describes the generic application usage of the entire SCTP
   association, including the associated SCTP streams.




Holmberg, et al.          Expires June 8, 2015                  [Page 5]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   NOTE: A mechanism on how to describe, and manage, individual SCTP
   streams within an SCTP association, is outside the scope of this
   specification.

4.4.  Syntax

       sctp-m-line = %x6d "="
        ("application" SP sctp-port SP "SCTP"  SP sctp-fmt CRLF) /
        ("application" SP sctp-port SP "SCTP/DTLS" SP sctp-fmt CRLF) /
        ("application" SP udp-port  SP "DTLS/SCTP" SP sctp-fmt CRLF)

       sctp-port = port

       udp-port = port

       sctp-fmt = association-usage

       association-usage = token

4.5.  Example

    TEMP:
    m=application 12345 DTLS/SCTP webrtc-datachannel
    a=max-message-size=100000
    m=application 12345 DTLS/SCTP webrtc-datachannel
    a=fmtp:webrtc-datachannel max-message-size=100000

5.  SDP 'sctp-port' Attribute

5.1.  General

   This section defines a new SDP media-level attribute, 'sctp-port'.
   The attribute can be associated with an SDP media descriptor (m-
   line) with a 'DTLS/SCTP' proto value, in which case the m- line port
   value indicates the port of the underlying transport protocol (UDP or
   TCP).

   TEMP: If the SDP sctp-port attribute is not present, the m- line
   SHOULD be discarded.  If the SDP sctp-port attribute is not present,
   the default value is 5000.

   Usage of the SDP sctp-port attribute with other proto values is not
   specified, and MUST be discarded if received.








Holmberg, et al.          Expires June 8, 2015                  [Page 6]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


5.2.  Syntax


       sctp-port-attr  =  "a=sctp-port:" port
       port            =  1*DIGIT


6.  SDP 'max-message-size' Attribute

6.1.  General

   The SDP 'max-message-size' attribute can be associated with an m-
   line to indicate the maximum message size that an SCTP endpoint is
   willing to receive on the SCTP association associated with the m-
   line.

   The remote peer MUST assume that larger messages will be rejected by
   the SCTP endpoint.  SCTP endpoints need to decide on appropriate
   behaviour in case a message that exceeds the maximum size needs to be
   sent.

   If the SDP 'max-message-size' attribute contains a maximum message
   size value of zero, it indicates the SCTP endpoint will handle
   messages of any size, subject to memory capacity etc.

   If the SDP 'max-message-size' attribute is not present, the default
   value is 64K.

6.2.  Syntax


       max-message-size-attr =  "a=max-message-size:" max-message-size
       max-message-size      =  1*DIGIT


7.  SDP 'fmtp' Attribute

7.1.  General

   The SDP 'fmtp' attribute can be used with an m- line, associated with
   an SCTP association, to indicate the maximum message size that an
   SCTP endpoint is willing to receive, for a particular SCTP
   association usage, on that SCTP association.

   The remote peer MUST assume that larger messages will be rejected by
   the SCTP endpoint.  SCTP endpoints need to decide on appropriate
   behaviour in case a message that exceeds the maximum size needs to be
   sent.



Holmberg, et al.          Expires June 8, 2015                  [Page 7]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   If the SDP 'fmtp' attribute contains a maximum message size value of
   zero, it indicates the SCTP endpoint will handle messages of any
   size, subject to memory capacity etc.

   If the SDP 'fmtp' attribute is not present, the default value is 64K.

   NOTE: This specification only defines the usage of the SDP 'max-
   message-size' attribute when associated with an m- line containing
   one of the following proto field values: 'SCTP', 'SCTP/DTLS' or
   'DTLS/SCTP'.  Usage of the attribute with other proto field values
   needs to be defined in a separate specification.

7.2.  Syntax


     sctpmap-attr      =  "a=fmtp:" association-usage [max-message-size]
     max-message-size  =  "max-message-size" EQUALS 1*DIGIT


8.  SCTP Association Management

8.1.  General

   The management of an SCTP association is identical to the management
   of a TCP connection.  An SCTP endpoints MUST follow the rules in
   Section 6 of [RFC4145] to manage SCTP associations.  Whether to use
   the SCTP ordered or unordered delivery service is up to the
   applications using the SCTP association, and this specification does
   not define a mechanism to indicate the type of delivery service using
   SDP.

8.2.  SDP sendrecv/sendonly/sendrecv/inactive Attribute

   This specification does not define any semantics for the SDP
   direction attributes [RFC4566].  Specifications for an individual
   SCTP association usage MAY define how the attributes can be used with
   that association usage.  If the semantics of these attributes for an
   SCTP association usage has not been defined, SDP direction attributes
   MUST be discarded if present.

8.3.  SDP setup Attribute

8.3.1.  General

   The SDP setup attribute is used to determine the 'active/passive'
   status of the endpoints, following the procedures for TCP in
   [RFC4145].




Holmberg, et al.          Expires June 8, 2015                  [Page 8]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


8.3.2.  SCTP Association Initiation

   Both the 'active' and 'passive' endpoint MUST initiate the SCTP
   association, and MUST use the same SCTP port as client port and
   server port (in order to prevent two separate SCTP associations from
   being established).

   NOTE: The procedure above is different from TCP, where only the
   'active' endpoint initiates the TCP connection [RFC4145].

   If the m- line proto field value is 'DTLS/SCTP', and if SCTP is
   carried on top of TCP, only the 'active' endpoint will initiate the
   TCP connection, following the procedures in [RFC4145], while both
   endpoints will initiate the SCTP association carried on top of the
   TCP connection.

8.3.3.  TLS Role Determination

   If the m- line proto field value is 'SCTP/DTLS' or 'DTLS/SCTP', the
   'active/passive' status is used to determine the TLS roles.
   Following the procedures in [RFC4572], the 'active' endpoint will
   take the TLS client role.

   Once a DTLS connection has been established, if the 'active/passive'
   status of the endpoints change during a session, a new DTLS
   connection MUST be established.  Therefore, endpoints SHOULD NOT
   change the 'active/passive' status in subsequent offers and answers,
   unless they want to establish a new DTLS connection.

   If the transport parameters or the key fingerprints change, the
   endpoints MUST establish a new DTLS connection.  In such case the
   'active/passive' status of the endpoints will again be determined
   following the procedures in [RFC4145], and the new status will be
   used to determine the TLS roles associated with the new DTLS
   connection.

   NOTE: The procedure above is identical to the one defined for SRTP-
   DTLS in [RFC5763].

   NOTE: A new DTLS connection needs to be established if the transport
   parameters or the key fingerprints change.

8.4.  SDP connection Attribute

   The SDP connection attribute is used following the procedures in
   [RFC4145], with the additional SCTP specific considerations described
   in this section.




Holmberg, et al.          Expires June 8, 2015                  [Page 9]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   The SDP connection attribute only applies to an SCTP association and,
   if the m- line proto field value is 'DTLS/SCTP', also to the TCP
   connection which is used to carry the SCTP association.  An attribute
   'new' value indicates that a new SCTP association (and, if
   applicable, the TCP connection, have to be established, following the
   procedures in [RFC4145].

   OPEN ISSUE #3: We need to determine whether the SDP connection
   attribute only applies to the transport-layer protocol, and not e.g.
   to an SCTP assocation carried on top of UDP or TCP.

   The SDP connection attribute value does not impact an existing DTLS
   connection.  Section 8.3.3 describes in which cases a new DTLS
   connections will be established.

   NOTE: if the m- line proto field value is 'SCTP/DTLS', and if the
   SCTP association is re-established, the DTLS connection also needs to
   be re-established.

   OPEN ISSUE #2: Verify that the above statement regarding 'SCTP/DTLS'
   is correct.

9.  SDP Offer/Answer Procedures

9.1.  General

   This section defines the SDP Offer/Answer [RFC3264] procedures for
   negotiating and establishing an SCTP association.  Unless explicitly
   stated, the procedures apply to all m- line proto values ('SCTP',
   'SCTP/DTLS' and 'DTLS/SCTP') defined in this specification.

   If the m- line proto value is 'SCTP/DTLS' or 'DTLS/SCTP', each
   endpoint MUST provide a certificate fingerprint, using the SDP
   'fingerprint' attribute [RFC4145], if the endpoint supports, and is
   willing to use, a cipher suite with an associated certificate.

   The authentication certificates are interpreted and validated as
   defined in [RFC4572].  Self-signed certificates can be used securely,
   provided that the integrity of the SDP description is assured as
   defined in [RFC4572].

   NOTE: The procedures apply to a specific m- line describing an SCTP
   association.  If an offer or answer contains multiple m- line
   describing SCTP associations, the procedures are applied separately
   to each m- line.






Holmberg, et al.          Expires June 8, 2015                 [Page 10]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


9.2.  Generating the Initial SDP Offer

   When the offerer creates an initial offer, the offerer:

   o  MUST, if the m- line proto field value is 'SCTP/DTLS' or 'DTLS/
      SCTP', associate an SDP setup attribute [Section 8.3], with an
      'actpass' value, with the m- line;

   o  MUST, if the m- line proto field is 'DTLS/SCTP', associate an SDP
      sctp-port attribute[Section 5] with the m- line;

   o  MUST associate an SDP 'connection' attribute [Section 8.4], with a
      'new' value, with the m- line; and

   o  MAY associate an SDP 'max-message-size' attribute [Section 7] with
      the m- line.

9.3.  Generating the SDP Answer

   When the answerer receives an offer, which contains an m- line
   describing an SCTP association, if the answerer accepts the m- line
   it:

   o  MUST insert a corresponiding m- line in the answer, with an
      identical m- line proto value [RFC3264];

   o  MUST, if the m- line proto field value is 'SCTP/DTLS' or 'DTLS/
      SCTP', associate an SDP setup attribute [Section 8.3], with an
      'active' or 'passive' value, with the m- line;

   o  MUST, if the m- line proto field is 'DTLS/SCTP', associate an SDP
      sctp-port attribute[Section 5] with the m- line;

   o  MAY associate an SDP 'max-message-size' attribute [Section 7] with
      the m- line.

   Once the answerer has sent the answer, the answerer:

   o  MUST, if an SCTP association associated with the m- line has yet
      not been established, or if an existing SCTP association is to be
      re-established, initiate the establishing of the SCTP association;
      and

   o  MUST, if the answerer is the 'active' endpoint, and if an DTLS
      connection associated with the m- line is to be established (or
      re-established), initiate the establishing of the DTLS connection
      (by sending a ClientHello message).




Holmberg, et al.          Expires June 8, 2015                 [Page 11]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   If the answerer does not accept the m- line in the offer, it MUST
   assign a zero port value to the corresponding m- line in the answer.
   In addition, the answerer MUST NOT establish an SCTP association, or
   a DTLS connection, associated with the m- line.

9.4.  Offerer Processing of the SDP Answer

   When the offerer receives an answer, which contains an m- line with a
   non-zero port value, describing an SCTP association, the offerer:

   o  MUST, if an SCTP association associated with the m- line has yet
      not been established, or if an existing SCTP association is to be
      re-established, initiate the establishing of the SCTP association;
      and

   o  MUST, if the offerer is the 'active' endpoint, and if an DTLS
      connection associated with the m- line is to be established (or
      re-established), initiate the establishing of the DTLS connection
      (by sending a ClientHello message).

   If the m- line in the answer contains a zero port value, the offerer
   MUST NOT establish an SCTP association, or a DTLS connection,
   associated with the m- line.

9.5.  Modifying the Session

   When an offerer sends an updated offer, in order to modify a
   previously established SCTP assiciation, it follows the procedures in
   Section 9.2, with the following exceptions:

   o  Unless the offerer wants to re-establish an existing SCTP
      association, the offerer MUST associate an SDP connection
      attribute, with an 'existing' value, with the m- line; and

   o  If the offerer wants to disable a previously established SCTP
      association, it MUST assign a zero port value to the m- line
      associated with the SCTP association, following the procedures in
      [RFC3264].

   NOTE: Different SCTP association usages might define protocol
   procedures etc that need to be performed before an SCTP association
   is terminated.  Such procedures are outside the scope of this
   specification.








Holmberg, et al.          Expires June 8, 2015                 [Page 12]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


10.  Multihoming Considerations

   SCTP supports multihoming.  An SCTP endpoint is considered multihomed
   if it has more than one IP address on which SCTP can be used.  An
   SCTP endpoint inform the remote peer about its IP addresses using the
   address parameters in the INIT/INIT-ACK chunk.  Therefore, when SDP
   is used to describe an SCTP association, while the "c=" line contains
   the address which was used to negotiate the SCTP association,
   multihomed SCTP endpoints might end up using other IP addresses.

   If an endpoint removes the IP address [RFC5061] that it offered in
   the SDP "c=" line associated with the SCTP association, it MUST send
   a new Offer, in which the "c=" line contains an IP address with is
   valid within the SCTP association.

   NOTE: In some network environments, intermediaries performing gate-
   and firewall control use the address information in the SDP "c=" and
   "m=" lines to authorize media, and will not pass media sent using
   other addresses.  In such network environment, if an SCTP endpoints
   wants to change the address information on which media is sent and
   received, it needs to send an updated Offer, in which the SDP "c="
   and "m=" lines contain the new address information.

   Multihoming is not supported when sending SCTP on top of DTLS, as
   DTLS does not expose address management to its upper layer.

11.  NAT Considerations

11.1.  General

   SCTP features not present in UDP or TCP, including the checksum
   (CRC32c) value calculated on the whole packet (rather than just the
   header), and multihoming, introduce new challenges for NAT traversal.
   [I-D.ietf-behave-sctpnat] defines an SCTP specific variant of NAT,
   which provides similar features of Network Address and Port
   Translation (NAPT).

   Current NATs typically do not support SCTP.  [RFC6951] defines a
   mechanism for sending SCTP on top of UDP, which makes it possible to
   use SCTP with NATs and firewalls that do not support SCTP.

11.2.  ICE Considerations

   At the time of writing this specification, no procedures have been
   defined for using ICE ICE (Interactive Connectivity Establishment)
   [RFC5768] together with SCTP.  Such procedures, including the
   associated SDP Offer/Answer procedures, are outside the scope of this
   specification, and might be defined in a future specification.



Holmberg, et al.          Expires June 8, 2015                 [Page 13]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


12.  Examples

   TODO: ADD EXAMPLES HERE

13.  Security Considerations

   [RFC4566] defines general SDP security considerations, while
   [RFC3264], [RFC4145] and [RFC4572] define security considerations
   when using the SDP Offer/Answer mechanism to negotiate media streams.

   [RFC4960] defines general SCTP security considerations.  security
   considerations on SCTP in general, while [RFC6083] defines security
   considerations when using DTLS on top of SCTP.

   This specification does not introduce new security considerations in
   addition to those defined in the specifications listed above.

14.  IANA Considerations

14.1.  New SDP proto values

   [RFC EDITOR NOTE: Please replace RFCXXXX with the RFC number of this
   document.]

   This document updates the "Session Description Protocol (SDP)
   Parameters" registry, following the procedures in [RFC4566], by
   adding the following values to the table in the SDP "proto" field
   registry:

                     +-------+-----------+-----------+
                     |  Type |  SDP Name | Reference |
                     +-------+-----------+-----------+
                     | proto |    SCTP   | [RFCXXXX] |
                     | proto | SCTP/DTLS | [RFCXXXX] |
                     | proto | DTLS/SCTP | [RFCXXXX] |
                     +-------+-----------+-----------+

                     Table 1: SDP "proto" field values

14.2.  New SDP Attribute

   [RFC EDITOR NOTE: Please replace RFCXXXX with the RFC number of this
   document.]

   This document defines a new SDP media-level attribute,'sctp-port', as
   follows:





Holmberg, et al.          Expires June 8, 2015                 [Page 14]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


       Attribute name:     sctp-port
       Type of attribute:  media
       Subject to charset: No
       Purpose:            Indicate the SCTP port value associated
                           with the SDP Media Description.
       Appropriate values: Integer
       Contact name:       Christer Holmberg
       Contact e-mail:     christer.holmberg@ericsson.com
       Reference:          RFCXXXX


14.3.  association-usage Name Registry

   [RFC EDITOR NOTE: Please replace RFCXXXX with the RFC number of this
   document.]

   This specification creates a new IANA registry, following the
   procedures in [RFC5226], for the "fmt" namespace associated with the
   'SCTP', 'SCTP/DTLS' and 'DTLS/SCTP' protocol identifiers.  Each "fmt"
   value describes the usage of an entire SCTP association, including
   all SCTP streams associated with the SCTP association.

   NOTE: Usage indication of individual SCTP streams is outside the
   scope of this specification.

   The "fmt" value, "association-usage", used with these "proto" is
   required.  It is defined in section Section 4.

   As part of this registry, IANA maintains the following information:

   association-usage Name:  .The identifier of the subprotocol, as will
      be used in the <sctp-fmtp> subfield.

   association-usage reference:  A reference to the document in which
      the the association usage is defined.

   association-usage names are to be subject to the "First Come First
   Served" IANA registration policy [RFC5226].

   IANA is asked to add initial values to the registry.











Holmberg, et al.          Expires June 8, 2015                 [Page 15]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


        |         name       |           Reference                 |
       -+--------------------+-------------------------------------+
        | webrtc-datachannel | draft-ietf-rtcweb-data-protocol-xx  |
       -+----------------------------------------------------------|


                                 Figure 1

15.  Acknowledgments

   The authors wish to thank Harald Alvestrand, Randell Jesup, Paul
   Kyzivat, Michael Tuexen for their comments and useful feedback.

16.  Change Log

   [RFC EDITOR NOTE: Please remove this section when publishing]

   Changes from draft-ietf-mmusic-sctp-sdp-08

   o  Default SCTP port removed

   o  - Usage of SDP sctp-port attribute mandatory

   o  SDP max-message-size attribute defined

   o  - Attribute definition

   o  - SDP Offer/Answer procedures

   o  Text about SDP direction attributes added

   o  Text about TLS role determination added

17.  References

17.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3264]  Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model
              with Session Description Protocol (SDP)", RFC 3264, June
              2002.

   [RFC4145]  Yon, D. and G. Camarillo, "TCP-Based Media Transport in
              the Session Description Protocol (SDP)", RFC 4145,
              September 2005.




Holmberg, et al.          Expires June 8, 2015                 [Page 16]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   [RFC4289]  Freed, N. and J. Klensin, "Multipurpose Internet Mail
              Extensions (MIME) Part Four: Registration Procedures", BCP
              13, RFC 4289, December 2005.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, July 2006.

   [RFC4572]  Lennox, J., "Connection-Oriented Media Transport over the
              Transport Layer Security (TLS) Protocol in the Session
              Description Protocol (SDP)", RFC 4572, July 2006.

   [RFC4960]  Stewart, R., "Stream Control Transmission Protocol", RFC
              4960, September 2007.

   [RFC5061]  Stewart, R., Xie, Q., Tuexen, M., Maruyama, S., and M.
              Kozuka, "Stream Control Transmission Protocol (SCTP)
              Dynamic Address Reconfiguration", RFC 5061, September
              2007.

   [RFC5226]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", BCP 26, RFC 5226,
              May 2008.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246, August 2008.

   [RFC6347]  Rescorla, E. and N. Modadugu, "Datagram Transport Layer
              Security Version 1.2", RFC 6347, January 2012.

   [RFC6838]  Freed, N., Klensin, J., and T. Hansen, "Media Type
              Specifications and Registration Procedures", BCP 13, RFC
              6838, January 2013.

   [I-D.ietf-tsvwg-sctp-dtls-encaps]
              Tuexen, M., Stewart, R., Jesup, R., and S. Loreto, "DTLS
              Encapsulation of SCTP Packets", draft-ietf-tsvwg-sctp-
              dtls-encaps-06 (work in progress), November 2014.

17.2.  Informative References

   [RFC5763]  Fischl, J., Tschofenig, H., and E. Rescorla, "Framework
              for Establishing a Secure Real-time Transport Protocol
              (SRTP) Security Context Using Datagram Transport Layer
              Security (DTLS)", RFC 5763, May 2010.

   [RFC5768]  Rosenberg, J., "Indicating Support for Interactive
              Connectivity Establishment (ICE) in the Session Initiation
              Protocol (SIP)", RFC 5768, April 2010.



Holmberg, et al.          Expires June 8, 2015                 [Page 17]


Internet-Draft    The SCTP protocol identifier for SDP     December 2014


   [RFC6083]  Tuexen, M., Seggelmann, R., and E. Rescorla, "Datagram
              Transport Layer Security (DTLS) for Stream Control
              Transmission Protocol (SCTP)", RFC 6083, January 2011.

   [RFC6951]  Tuexen, M. and R. Stewart, "UDP Encapsulation of Stream
              Control Transmission Protocol (SCTP) Packets for End-Host
              to End-Host Communication", RFC 6951, May 2013.

   [I-D.ietf-behave-sctpnat]
              Stewart, R., Tuexen, M., and I. Ruengeler, "Stream Control
              Transmission Protocol (SCTP) Network Address Translation",
              draft-ietf-behave-sctpnat-09 (work in progress), September
              2013.

Authors' Addresses

   Christer Holmberg
   Ericsson
   Hirsalantie 11
   Jorvas  02420
   Finland

   Email: christer.holmberg@ericsson.com


   Salvatore Loreto
   Ericsson
   Hirsalantie 11
   Jorvas  02420
   Finland

   Email: Salvatore.Loreto@ericsson.com


   Gonzalo Camarillo
   Ericsson
   Hirsalantie 11
   Jorvas  02420
   Finland

   Email: Gonzalo.Camarillo@ericsson.com










Holmberg, et al.          Expires June 8, 2015                 [Page 18]