Internet Engineering Task Force T. Savolainen
Internet-Draft Nokia
Intended status: Standards Track J. Kato
Expires: November 26, 2012 NTT
T. Lemon
Nominum, Inc.
May 25, 2012
Improved Recursive DNS Server Selection for Multi-Interfaced Nodes
draft-ietf-mif-dns-server-selection-09
Abstract
A multi-interfaced node is connected to multiple networks, some of
which may be utilizing private DNS namespaces. A node commonly
receives recursive DNS server configuration information from all
connected networks. Some of the recursive DNS servers may have
information about namespaces other servers do not have. When a
multi-interfaced node needs to utilize DNS, the node has to choose
which of the recursive DNS servers to contact to. This document
describes DHCPv4 and DHCPv6 options that can be used to configure
nodes with information required to perform informed recursive DNS
server selection decisions.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on November 26, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Savolainen, et al. Expires November 26, 2012 [Page 1]
Internet-Draft MIF and RDNSS selection May 2012
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Requirements Language . . . . . . . . . . . . . . . . . . 5
2. Private namespaces and problems for multi-interfaced nodes . . 5
2.1. Fully qualified domain names with limited scopes . . . . . 5
2.2. Network interface specific IP addresses . . . . . . . . . 6
2.3. A problem not fully solved by the described solution . . . 8
3. Deployment scenarios . . . . . . . . . . . . . . . . . . . . . 8
3.1. CPE deployment scenario . . . . . . . . . . . . . . . . . 8
3.2. Cellular network scenario . . . . . . . . . . . . . . . . 9
3.3. VPN scenario . . . . . . . . . . . . . . . . . . . . . . . 9
3.4. Dual-stack accesses . . . . . . . . . . . . . . . . . . . 9
4. Improved RDNSS selection . . . . . . . . . . . . . . . . . . . 9
4.1. Procedure for prioritizing RDNSSes and handling
responses . . . . . . . . . . . . . . . . . . . . . . . . 9
4.2. RDNSS selection DHCPv6 option . . . . . . . . . . . . . . 12
4.3. RDNSS selection DHCPv4 option . . . . . . . . . . . . . . 14
4.4. Limitations on use . . . . . . . . . . . . . . . . . . . . 16
4.5. Coexistence of various RDNSS configuration tools . . . . . 16
4.6. Considerations on follow-up queries . . . . . . . . . . . 17
5. Example of a node behavior . . . . . . . . . . . . . . . . . . 18
6. Scalability considerations . . . . . . . . . . . . . . . . . . 20
7. Considerations for network administrators . . . . . . . . . . 20
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 20
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 21
10. Security Considerations . . . . . . . . . . . . . . . . . . . 21
10.1. Attack vectors . . . . . . . . . . . . . . . . . . . . . . 21
10.2. Trust levels of network interfaces . . . . . . . . . . . . 21
10.3. Importance of following the algorithm . . . . . . . . . . 21
11. References . . . . . . . . . . . . . . . . . . . . . . . . . . 22
11.1. Normative References . . . . . . . . . . . . . . . . . . . 22
11.2. Informative References . . . . . . . . . . . . . . . . . . 22
Appendix A. Possible alternative practices for RDNSS selection . 23
A.1. Sending queries out on multiple interfaces in parallel . . 23
A.2. Search list option for DNS forward lookup decisions . . . 24
A.3. More specific routes for reverse lookup decision . . . . . 24
A.4. Longest matching prefix for reverse lookup decision . . . 24
Savolainen, et al. Expires November 26, 2012 [Page 2]
Internet-Draft MIF and RDNSS selection May 2012
Appendix B. DNSSEC and multiple answers validating with
different trust anchors . . . . . . . . . . . . . . . 24
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 25
Savolainen, et al. Expires November 26, 2012 [Page 3]
Internet-Draft MIF and RDNSS selection May 2012
1. Introduction
A multi-interfaced node faces several problems a single-homed node
does not encounter, as is described in [RFC6418]. This document
studies in detail the problems private namespaces may cause for
multi-interfaced nodes and provides a solution. The node may be
implemented as a host or as a router.
We start from the premise that network operators sometimes include
private namespaces in the answers they provide from Recursive DNS
Servers (RDNSS), and that those private namespaces are at least as
useful to nodes as the answers from the public DNS. When private
namespaces are visible for a node, some RDNSSes have information
other RDNSSes do not have. The node ought to be able to ask right
RDNSS for the information it needs.
An example of an application that benefits from multi-interfacing is
a web browser that commonly accesses many different destinations,
each of which is available only on one network. The browser
therefore needs to be able to communicate over different network
interfaces, depending on the destination it is trying to reach.
In deployments where private namespaces are present, selection of
correct route and destination and source addresses for the actual IP
connection is crucial as well, as the resolved destination's IP
addresses may be only usable on the network interface over which the
name was resolved on. Hence solution described in this document is
assumed to be commonly used in combination with tools for delivering
additional routing and source and destination address selection
policies.
This document is organized in the following manner. Background
information about problem descriptions and example deployment
scenarios are included in Section 2 and Section 3. Section 4
contains all normative descriptions for DHCP options and node
behavior. Informative Section 5 illustrates behavior of a node
implementing functionality described in the Section 4. Section 6
contains informational considerations about scalability. Section 7
contains normative guidelines related to creation of private
namespaces. Informational Section 10 summarizes identified security
considerations.
The Appendix A describes best current practices possible with tools
preceding this document and that may be possibilities on networks not
supporting the solution described in this document.
Savolainen, et al. Expires November 26, 2012 [Page 4]
Internet-Draft MIF and RDNSS selection May 2012
1.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Private namespaces and problems for multi-interfaced nodes
This section describes two node multi-interfacing related private
namespace scenarios for which the procedure described in Section 4
provides a solution for. Additionally, Section 2.3 describes a
problem for which this document provides only partial solution.
2.1. Fully qualified domain names with limited scopes
A multi-interfaced node may be connected to one or more networks that
are using private namespaces. As an example, the node may have
simultaneously open a wireless LAN (WLAN) connection to the public
Internet, cellular connection to an operator network, and a virtual
private network (VPN) connection to an enterprise network. When an
application initiates a connection establishment to an FQDN, the node
needs to be able to choose the right RDNSS for making a successful
DNS query. This is illustrated in the figure 1. An FQDN for a
public name can be resolved with any RDNSS, but for an FQDN of
enterprise's or operator's service's private name the node needs to
be able to correctly select the right RDNSS for the DNS resolution,
i.e. do also network interface selection already before destination's
IP address is known.
Savolainen, et al. Expires November 26, 2012 [Page 5]
Internet-Draft MIF and RDNSS selection May 2012
+---------------+
| RDNSS with | | Enterprise
+------+ | public + |----| Intranet
| | | enterprise's | |
| |===== VPN =======| private names | |
| | +---------------+ +----+
| MIF | | FW |
| node | +----+
| | +---------------+ |
| |----- WLAN ------| RDNSS with |----| Public
| | | public names | | Internet
| | +---------------+ +----+
| | | FW |
| | +---------------+ +----+
| |---- cellular ---| RDNSS with | |
+------+ | public + | | Operator
| operator's |----| Intranet
| private names | |
+---------------+
Private DNS namespaces illustrated
Figure 1
2.2. Network interface specific IP addresses
In the second problem an FQDN is valid and resolvable via different
network interfaces, but to different and not necessarily globally
reachable IP addresses, as is illustrated in the figure 2. Node's
routing and source and destination address selection mechanism must
ensure the destination's IP address is only used in combination with
source IP addresses of the network interface the name was resolved
on.
Savolainen, et al. Expires November 26, 2012 [Page 6]
Internet-Draft MIF and RDNSS selection May 2012
+--------------------| |
+------+ IPv6 | RDNSS A |------| IPv6
| |-- interface 1 --| saying Peer is | |
| | | at: 2001:0db8:0::1 | |
| MIF | +--------------------+ +------+
| node | | Peer |
| | +--------------------+ +------+
| | IPv6 | RDNSS B | |
| |-- interface 2 --| saying Peer is | |
+------+ | at: 2001:0db8:1::1 |------| IPv6
+--------------------+ |
Private DNS namespaces and different IP addresses for an FQDN on
interfaces 1 and 2.
Figure 2
Similar situation can happen with IPv6 protocol translation and AAAA
record synthesis [RFC6147]. A synthetic AAAA record is guaranteed to
be valid only on a network it was synthesized on. Figure 3
illustrates a scenario where the peer's IPv4 address is synthesized
into different IPv6 addresses by RDNSSes A and B.
+-------------------| +-------+
+------+ IPv6 | RDNSS A |----| NAT64 |
| |-- interface 1 --| saying Peer is | +-------+
| | | at: A_Pref96:IPv4 | |
| MIF | +-------------------+ | +------+
| node | IPv4 +---| Peer |
| | +-------------------+ | +------+
| | IPv6 | RDNSS B | |
| |-- interface 2 --| saying Peer is | +-------+
+------+ | at: B_Pref96:IPv4 |----| NAT64 |
+-------------------+ +-------+
AAAA synthesis results in network interface specific IPv6 addresses.
Figure 3
It is worth noting is that network specific IP addresses can cause
problems also for a single-homed node, if the node retains DNS cache
during movement from one network to another. After the network
change, a node may have entries in its DNS cache that are no longer
correct or appropriate for its new network position.
Savolainen, et al. Expires November 26, 2012 [Page 7]
Internet-Draft MIF and RDNSS selection May 2012
2.3. A problem not fully solved by the described solution
A more complex scenario is an FQDN, which in addition to possibly
resolving into network interface specific IP addresses, identifies on
different network interfaces completely different peer entities with
potentially different set of service offerings. In even more complex
scenario, an FQDN identifies unique peer entity, but one that
provides different services on its different network interfaces. The
solution described in this document is not able to tackle these
higher layer issues. In fact, these problems may be solvable only by
manual user intervention.
However, when DNSSEC is used, the DNSSEC validation procedure may
provide assistance for selecting correct responses for some, but not
all, use cases. A node may prefer to use the DNS answer that
validates with the preferred trust anchor.
3. Deployment scenarios
This document has been written with three particular deployment
scenarios in mind. First being a Consumer Premises Equipment (CPE)
with two or more uplink VLAN connections. Second scenario involves a
cellular device with two uplink Internet connections: WLAN and
cellular. Third scenario is for VPNs, where use of local RDNSS may
be preferred for latency reasons, but enterprise's RDNSS must be used
to resolve private names used by the enterprise.
3.1. CPE deployment scenario
A home gateway may have two uplink connections leading to different
networks, as is described in
[I-D.ietf-v6ops-ipv6-multihoming-without-ipv6nat]. In the two
uplinks scenario only one uplink connection leads to the Internet,
while another uplink connection leads to a private network utilizing
private namespaces.
It is desirable that the CPE does not have to send DNS queries over
both uplink connections, but instead CPE should send default queries
to the RDNSS of the interface leading to the Internet, and queries
related to private namespace to the RDNSS of the private network.
In this scenario the legacy hosts can be supported by deploying DNS
proxy on the CPE and configuring hosts in the LAN to talk to the DNS
proxy. However, updated hosts would be able to talk directly to the
correct RDNSS of each uplink ISP's RDNSS. It is deployment decision
whether the updated hosts would be pointed to DNS proxy or to actual
RDNSSes.
Savolainen, et al. Expires November 26, 2012 [Page 8]
Internet-Draft MIF and RDNSS selection May 2012
Depending on actual deployments, all VLAN connections might be
considered as trusted.
3.2. Cellular network scenario
A cellular device may have both WLAN and cellular network interfaces
up. In such a case it is often desirable to use WLAN by default,
except for those connections cellular network operator wants to go
over cellular interface. The cellular network may utilize private
names and hence the cellular device needs to ask for those through
the cellular interface.
In this scenario cellular interface can be considered trusted and
WLAN oftentimes untrusted.
3.3. VPN scenario
Depending on a deployment, there may be interest to use VPN only for
the traffic destined to a enterprise network. The enterprise may be
using private namespace, and hence related DNS queries should be send
over VPN to the enterprise's RDNSS, while by default RDNSS of a local
access network may be used.
In this scenario VPN interface can be considered trusted and local
access network untrusted.
3.4. Dual-stack accesses
In all three scenarios one or more of the connected networks may
support both IPv4 and IPv6. In such a case both or either of DHCPv4
and DHCPv6 can be used to learn RDNSS selection information.
4. Improved RDNSS selection
This section describes DHCP options and a procedure that a (stub /
proxy) resolver may utilize for improved RDNSS selection in the face
of private namespaces and multiple simultaneously active network
interfaces.
4.1. Procedure for prioritizing RDNSSes and handling responses
A resolver SHALL build a priority list of RDNSSes it will contact to
depending on the query. To build the list in an optimal way, a node
SHOULD ask with DHCP which RDNSSes of each network interface are most
likely to be able to successfully serve forward lookup requests
matching to specific domain or reverse (PTR record) lookup requests
matching to specific network addresses (later referred as "network").
Savolainen, et al. Expires November 26, 2012 [Page 9]
Internet-Draft MIF and RDNSS selection May 2012
For security reasons the RDNSS selection information MUST be used
only when it is safe to do so, see Section 4.4 for details.
The node SHOULD create node specific routes for RDNSS addresses
learned via DHCP. The route must point to the interface each RDNSS
address was learned on. This is required to ensure DNS queries are
sent out via the right network interface.
A resolver lacking more specific information shall assume that all
information is available from any RDNSS of any network interface.
The RDNSSes learnt by other RDNSS address configuration methods MUST
be handled as medium priority default RDNSSes (see also Section 4.5).
When a DNS query needs to be made, the resolver SHOULD give highest
precedence to the RDNSSes explicitly known to serve matching domain
or network. The resolver MUST take into account differences in trust
levels of pieces of received RDNSS selection information. The
resolver MUST prefer RDNSSes of trusted interfaces. The RDNSSes of
untrusted interfaces may be of highest priority only if trusted
interfaces specifically configure low priority RDNSSes. The non-
exhaustive list on figure 4 illustrates how the different trust
levels of received RDNSS selection information SHOULD influence the
RDNSS selection logic.
Trustworthiness of an interface and configuration information
received over the interface is implementation and/or node deployment
dependent. Trust may be based on, for example, on the nature of an
interface. For example, an authenticated and encrypted VPN or layer
2 connections to a trusted home network may be considered as trusted,
and an unauthenticated and unencrypted connection to an unknown
visited network may be considered as untrusted. In some occasions an
interface may be considered trusted only if explicitly configured to
be trusted.
A resolver SHOULD prioritize between equally trusted RDNSSes with
help of the DHCP option preference field. The resolver MUST NOT
prioritize less trusted RDNSSes higher than trusted, even in the case
of less trusted RDNSS would apparently have additional information.
In the case of all other things being equal the resolver shall make
the prioritization decision based on its internal preferences.
Savolainen, et al. Expires November 26, 2012 [Page 10]
Internet-Draft MIF and RDNSS selection May 2012
Information from | Information from | Resulting RDNSS
more trusted | less trusted | priority
interface A | interface B | selection
--------------------------+------------------------+--------------------
1. Medium priority | Medium priority | Default: A, then B
default | default |
--------------------------+------------------------+--------------------
2. Medium priority | High priority default | Default: A, then B
default | High priority specific | Specific: A, then B
--------------------------+------------------------+--------------------
3. Low priority default | Medium priority | Default: B, then A
| default |
--------------------------+------------------------+--------------------
4. Low priority default | Medium priority | Default: B, then A
High priority specific | default | Specific: A, then B
--------------------------+------------------------+--------------------
Figure 4: RDNSS selection in the case of different trust levels
Because DNSSEC provides cryptographic assurance of the integrity of
DNS data, data that can be validated under DNSSEC is necessarily to
be preferred over data that cannot be. There are two ways that a
node can determine that data is valid under DNSSEC. The first is to
perform DNSSEC validation itself. The second is to have a secure
connection to an authenticated RDNSS, and to rely on that RDNSS to
perform DNSSEC validation (signalling that it has done so using the
AD bit). If a DNS response is not proven to be unmolested using
DNSSEC, then a node cannot make a decision to prefer data from any
interface with any great assurance: any response could be forged, and
there is no way to detect the forgery without DNSSEC.
A node SHALL send requests to RDNSSes in the order defined by the
priority list until an acceptable reply is received, all replies are
received, or a time out occurs. In the case of a requested name
matching to a specific domain or network rule accepted from any
interface, a DNSSEC-aware resolver MUST NOT proceed with a reply that
cannot be validated using DNSSEC until all RDNSSes on the priority
list have been contacted or timed out. This protects against
possible redirection attacks. In the case of the requested name not
matching to any specific domain or network, first received response
from any RDNSS MAY be considered acceptable. A DNSSEC-aware node MAY
always contact all RDNSSes in an attempt to receive a response that
can be validated, but contacting all RDNSSes is not mandated for the
default case as in some deployments that would consume excess
resources.
The resolver SHOULD avoid sending queries over different network
interfaces in parallel as that wastes resources such as energy. The
Savolainen, et al. Expires November 26, 2012 [Page 11]
Internet-Draft MIF and RDNSS selection May 2012
amount of wasted energy can be significant, for example when radio
interfaces has to be started just for the queries.
In the case of validated NXDOMAIN response being received from a
RDNSS that can provide answers for the queried name a node MUST NOT
accept non-validated replies from other RDNSSes (see Appendix B for
considerations related to multiple trust anchors.
4.2. RDNSS selection DHCPv6 option
DHCPv6 option described below can be used to inform resolvers which
RDNSS should be contacted when initiating forward or reverse DNS
lookup procedures. This option is DNS record type agnostic and
applies, for example, equally to both A and AAAA queries.
Savolainen, et al. Expires November 26, 2012 [Page 12]
Internet-Draft MIF and RDNSS selection May 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_DNS_SERVER_SELECT | option-len |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| DNS-recursive-name-server (IPv6 address) |
| |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |prf| |
+-+-+-+-+-+-+-+-+ Domains and networks |
| (variable length) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code: OPTION_DNS_SERVER_SELECT (TBD)
option-len: Length of the option in octets
DNS-recursive-name-server: An IPv6 address of RDNSS
Reserved: Field reserved for the future. MUST be set to zero.
prf: RDNSS preference, for selecting between
equally trusted RDNSSes:
01 High
00 Medium
11 Low
10 Reserved
Domains and networks: The list of domains for forward DNS
lookup and networks for reverse DNS lookup the RDNSS
has special knowledge about. Field MUST be encoded as
specified in Section "Representation and use of
domain names" of [RFC3315].
Special domain of "." is used to indicate
capability to resolve global names and act as a
default RDNSS. Lack of "."
domain on the list indicates RDNSS only has
information related to listed domains and networks.
Networks for reverse mapping are encoded as
defined for ip6.arpa [RFC3596] or in-addr.arpa [RFC2317].
DHCPv6 option for explicit domain configuration
Figure 5
Savolainen, et al. Expires November 26, 2012 [Page 13]
Internet-Draft MIF and RDNSS selection May 2012
A node SHOULD include an OPTION_ORO option in a DHCPv6 request with
the OPTION_DNS_SERVER_SELECT option code to inform the DHCPv6 server
about the support for the improved RDNSS selection logic. DHCPv6
server receiving this information MAY then choose to provision RDNSS
addresses only with the OPTION_DNS_SERVER_SELECT.
The OPTION_DNS_SERVER_SELECT contains one or more domains the related
RDNSS has particular knowledge of. The option can occur multiple
times in a single DHCPv6 message, if multiple RDNSS are to be
configured.
IPv6 networks should cover all the domains configured in this option.
Networks should be as long as possible to avoid potential collision
with information received on other option instances or with options
received from DHCPv6 servers of other network interfaces.
Overlapping IPv6 networks are interpreted so that the resolver can
use any of the RDNSSes for queries matching the networks.
If the OPTION_DNS_SERVER_SELECT contains a RDNSS address already
learned from other DHCPv6 servers of the same network, and contains
new domains or networks, the node SHOULD append the information to
the information received earlier. The node MUST NOT remove
previously obtained information. However, the node SHOULD NOT extent
lifetime of earlier information either. In the case of conflicting
RDNSS address is learned from less trusted interface, the node MUST
ignore the option.
As the RDNSS options of [RFC3646], the OPTION_DNS_SERVER_SELECT
option MUST NOT appear in any other than the following DHCPv6
messages: Solicit, Advertise, Request, Renew, Rebind, Information-
Request, and Reply.
The information conveyed in OPTION_DNS_SERVER_SELECT is considered
valid until changed or refreshed by general events that trigger
DHCPv6 action. In the event that it is desired for the client to
request a refresh of the information, use of generic DHCPv6
Information Refresh Time Option, as specified in [RFC4242] is
RECOMMENDED.
4.3. RDNSS selection DHCPv4 option
DHCPv4 option described below can be used to inform resolvers which
RDNSS should be contacted when initiating forward or reverse DNS
lookup procedures. This option is DNS record type agnostic and
applies, for example, equally to both A and AAAA queries.
Savolainen, et al. Expires November 26, 2012 [Page 14]
Internet-Draft MIF and RDNSS selection May 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| CODE | Len | Reserved |prf| Primary .. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| .. DNS-recursive-name-server's IPv4 address | Secondary .. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| .. DNS-recursive-name-server's IPv4 address | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| |
+ Domains and networks |
| (variable length) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
option-code: OPTION_DNS_SERVER_SELECT (TBD)
option-len: Length of the option in octets
Reserved: Field reserved for the future. MUST be set to zero.
prf: RDNSSes preference, for selecting between
equally trusted RDNSSes:
01 High
00 Medium
11 Low
10 Reserved
Primary DNS-recursive-name-server's IPv4 address: Address of
a primary RDNSS
Secondary DNS-recursive-name-server's IPv4 address: Address of
a secondary RDNSS or 0.0.0.0 if not configured
Domains and networks: The list of domains for forward DNS lookup
and networks for reverse DNS lookup the RDNSSes
have special knowledge about. Field MUST be encoded as
specified in Section "Representation and use of
domain names" of [RFC3315].
Special domain of "." is used to indicate
capability to resolve global names and act as
default RDNSS. Lack of "."
domain on the list indicates RDNSSes only have
information related to listed domains and networks.
Networks for reverse mapping are encoded as
defined for ip6.arpa [RFC3596] or in-addr.arpa [RFC2317].
DHCPv4 option for explicit domain configuration
Savolainen, et al. Expires November 26, 2012 [Page 15]
Internet-Draft MIF and RDNSS selection May 2012
Figure 6
The OPTION_DNS_SERVER_SELECT contains one or more domains the primary
and secondary RDNSSes have particular knowledge of. If the length of
the domains and networks field causes option length to exceed the
maximum permissible for a single option (255 octets), then multiple
options MAY be used, as described in "Encoding Long Options in the
Dynamic Host Configuration Protocol (DHCPv4)" [RFC3396]. When
multiple options are present, the data portions of all option
instances are concatenated together.
If the OPTION_DNS_SERVER_SELECT contains a RDNSS address already
learned from other DHCPv4 servers of the same network, and contains
new domains or networks, the node SHOULD append the information to
the information received earlier. The node MUST NOT remove
previously obtained information. However, the node SHOULD NOT extent
lifetime of earlier information either. In the case of conflicting
RDNSS address is learned from less trusted interface, the node MUST
ignore the option.
4.4. Limitations on use
Use of OPTION_DNS_SERVER_SELECT is ideal in the following
environments, but SHOULD NOT be enabled by default otherwise:
1. The RDNSS selection option is delivered across a secure, trusted
channel.
2. The RDNSS selection option is not secured, but the client on a
node does DNSSEC validation.
3. The RDNSS selection option is not secured, the resolver does
DNSSEC validation, and the client communicates with the resolver
configured with RDNSS selection option over a secure, trusted
channel.
4. The IP address of RDNSS that is being recommended in the RDNSS
selection option is known and trusted by the client; that is, the
RDNSS selection option serves not to introduce the client to a new
RDNSS, but rather to inform it that RDNSS it has already been
configured to trust is available to it for resolving certain domains.
4.5. Coexistence of various RDNSS configuration tools
The DHCPv4 and DHCPv6 OPTION_DNS_SERVER_SELECT options are designed
to coexist between each other and with other tools used for RDNSS
address configuration.
Savolainen, et al. Expires November 26, 2012 [Page 16]
Internet-Draft MIF and RDNSS selection May 2012
For RDNSS selection purposes information received from all tools
should be combined together into a single list, as discussed in
Section 4.1.
In the case of DHCPv4 and DHCPv6 providing conflicting RDNSS
selection information on the same interface, or on the equally
trusted interfaces, the node SHALL firstly prefer DHCP-version
possibly securing OPTION_DNS_SERVER_SELECT, and secondly prefer
DHCPv6 over DHCPv4.
The RDNSSes learned via other tools than OPTION_DNS_SERVER_SELECT
MUST be handled as default RDNSSes, with medium preference, when
building a list of RDNSSes to talk to (see Section 4.1).
The non-exhaustive list of possible other sources for RDNSS address
configuration are:
(1) DHCPv6 OPTION_DNS_SERVERS defined in [RFC3646].
(2) DHCPv4 Domain Name Server Option defined in [RFC2132].
(3) IPv6 Router Advertisement RDNSS Option defined in [RFC6106].
When the OPTION_DNS_SERVER_SELECT contains default RDNSS address and
other sources are providing RNDSS addresses, the resolver MUST make
the decision which one to prefer based on RDNSS preference field
value. If OPTION_DNS_SERVER_SELECT defines medium preference then
RDNSS from OPTION_DNS_SERVER_SELECT SHALL be selected.
If multiple sources are providing same RDNSS(es) IP address(es), each
address MUST be added to the RDNSS list only once.
If a node had indicated support for OPTION_DNS_SERVER_SELECT in
DHCPv6 request, the DHCPv6 server may choose to omit sending of
OPTION_DNS_SERVERS. This enables offloading use case where network
administrator wishes to only advertise low priority default RDNSSes.
4.6. Considerations on follow-up queries
Any follow-up queries that are performed on the basis of an answer
received on an interface MUST continue to use the same interface,
irrespective of the RDNSS selection settings on any other interface.
For example, if a node receives a reply with a canonical name (CNAME)
or delegation name (DNAME) the follow-up queries MUST be sent to
RDNSS(es) of the same interface, or to same RDNSS, irrespectively of
the FQDN received. Otherwise referrals may fail.
Savolainen, et al. Expires November 26, 2012 [Page 17]
Internet-Draft MIF and RDNSS selection May 2012
5. Example of a node behavior
Figure 7 illustrates node behavior when it initializes two network
interfaces for parallel usage and learns domain and network
information from DHCPv6 servers.
Application Node DHCPv6 server DHCPv6 server
on interface 1 on interface 2
| | |
| +-----------+ |
(1) | | open | |
| | interface | |
| +-----------+ |
| | |
(2) | |---option REQ-->|
| |<--option RESP--|
| | |
| +-----------+ |
(3) | | store | |
| | domains | |
| +-----------+ |
| | |
| +-----------+ |
(4) | | open | |
| | interface | |
| +-----------+ |
| | | |
(5) | |---option REQ------------------->|
| |<--option RESP-------------------|
| | | |
| +----------+ | |
(6) | | store | | |
| | domains | | |
| +----------+ | |
| | | |
Illustration of learning domains
Figure 7
Flow explanations:
1. A node opens its first network interface
2. The node obtains domain 'domain1.example.com' and IPv6 network
'0.8.b.d.0.1.0.0.2.ip6.arpa' for the new interface 1 from DHCPv6
server
Savolainen, et al. Expires November 26, 2012 [Page 18]
Internet-Draft MIF and RDNSS selection May 2012
3. The node stores the learned domains and IPv6 networks for later
use
4. The node opens its second network interface 2
5. The node obtains domain 'domain2.example.com' and IPv6 network
information, say '1.8.b.d.0.1.0.0.2.ip6.arpa' for the new
interface 2 from DHCPv6 server
6. The node stores the learned domains and networks for later use
Figure 8 below illustrates how a resolver uses the learned domain
information. Network information use for reverse lookups is not
illustrated, but that would go as the figure 7 example.
Application Node RDNSS RDNSS
on interface 1 on interface 2
| | | |
(1) |--Name REQ-->| | |
| | | |
| +----------------+ | |
(2) | | RDNSS | | |
| | prioritization | | |
| +----------------+ | |
| | | |
(3) | |------------DNS resolution------>|
| |<--------------------------------|
| | | |
(4) |<--Name resp-| | |
| | | |
Example on choosing interface based on domain
Figure 8
Flow explanations:
1. An application makes a request for resolving an FQDN, e.g.
'private.domain2.example.com'
2. A node creates list of RDNSSes to contact to and uses configured
RDNSS selection information and stored domain information on
prioritization decisions.
3. The node has chosen interface 2, as from DHCPv6 it was learned
earlier that the interface 2 has domain 'domain2.example.com'.
The node then resolves the requested name using interface 2's
Savolainen, et al. Expires November 26, 2012 [Page 19]
Internet-Draft MIF and RDNSS selection May 2012
RDNSS to an IPv6 address
4. The node replies to application with the resolved IPv6 address
6. Scalability considerations
The size limitations of DHCP messages limit the number of domains and
networks that can be carried in configuration options. Including the
domains and networks in a DHCP option is best suited for deployments
where relatively few carefully selected domains and networks are
adequate.
7. Considerations for network administrators
Network administrators deploying private namespaces should assist
advanced nodes in their RDNSS selection process by providing
information described within this document.
Private namespaces MUST be globally unique in order to keep DNS
unambiguous and henceforth avoiding caching related issues and
destination selection problems (see Section 2.3). Exceptions to this
rule are domains utilized for local name resolution (such as .local).
Private namespaces MUST only consist of subdomains of domains for
which the relevant operator provides authoritative name service.
Thus, subdomains of example.com are permitted in the private
namespace served by an operator's RDNSSes only if the same operator
provides an SOA record for example.com.
To counter against attacks against private namespaces, administrators
utilizing this tool SHOULD deploy DNSSEC for their zone.
8. Acknowledgements
The author would like to thank following people for their valuable
feedback and improvement ideas: Mark Andrews, Jari Arkko, Marcelo
Bagnulo, Brian Carpenter, Stuart Cheshire, Lars Eggert, Tomohiro
Fujisaki, Peter Koch, Suresh Krishnan, Murray Kucherawy, Edward
Lewis, Kurtis Lindqvist, Arifumi Matsumoto, Erik Nordmark, Steve
Padgett, Fabien Rapin, Matthew Ryan, Dave Thaler, Margaret Wasserman,
Dan Wing, and Dec Wojciech. Ted Lemon and Julien Laganier receive
special thanks for their contributions to security considerations.
This document was prepared using xml2rfc template and the related
web-tool.
Savolainen, et al. Expires November 26, 2012 [Page 20]
Internet-Draft MIF and RDNSS selection May 2012
9. IANA Considerations
This memo requests IANA to assign two new option codes. First option
code is requested to be assigned for DHCPv4 RDNSS Selection option
(TBD) from the DHCP option code space defined in section "New DHCP
option codes" of RFC 2939. Second option code is requested to be
assigned to the DHCPv6 RDNSS Selection option (TBD) from the DHCPv6
option code space defined in section "IANA Considerations" of RFC
3315.
10. Security Considerations
10.1. Attack vectors
It is possible that attackers might try to utilize
OPTION_DNS_SERVER_SELECT option to redirect some or all DNS queries
sent by a resolver to undesired destinations. The purpose of an
attack might be denial-of-service, preparation for man-in-the-middle
attack, or something akin.
Attackers might try to lure specific traffic by advertising domains
and networks from very small to very large scope or simply by trying
to place attacker's RDNSS as the highest priority default RDNSS.
The best countermeasure for nodes is to implement validating DNSSEC
aware resolvers. Trusting on validation done by a RDNSS is a
possibility only if a node trusts the RDNSS and can use a secure
channel for DNS messages.
10.2. Trust levels of network interfaces
Decision on trust levels of network interfaces depends very much on
deployment scenario and types of network interfaces. For example,
unmanaged WLAN may be considered less trustworthy than managed
cellular or VPN connections. An implementation may not be able to
determine trust levels without explicit configuration provided by
user or administrator. Therefore, for example, an implementation may
not by default trust configuration received even over VPN interfaces.
The decision on levels of trust may be made by implementation, by
node administrators, or for example by other standards defining
organizations as part of system design work.
10.3. Importance of following the algorithm
The Section 4 uses normative language for describing node internal
behavior in order to ensure nodes would not open up new attack
Savolainen, et al. Expires November 26, 2012 [Page 21]
Internet-Draft MIF and RDNSS selection May 2012
vectors by accidental use of RDNSS selection options. During the
standards work consensus was that it is safer to not to enable this
option always by default, but only when deemed useful and safe.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2132] Alexander, S. and R. Droms, "DHCP Options and BOOTP Vendor
Extensions", RFC 2132, March 1997.
[RFC2317] Eidnes, H., de Groot, G., and P. Vixie, "Classless IN-
ADDR.ARPA delegation", BCP 20, RFC 2317, March 1998.
[RFC3315] Droms, R., Bound, J., Volz, B., Lemon, T., Perkins, C.,
and M. Carney, "Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 3315, July 2003.
[RFC3396] Lemon, T. and S. Cheshire, "Encoding Long Options in the
Dynamic Host Configuration Protocol (DHCPv4)", RFC 3396,
November 2002.
[RFC3596] Thomson, S., Huitema, C., Ksinant, V., and M. Souissi,
"DNS Extensions to Support IP Version 6", RFC 3596,
October 2003.
[RFC4242] Venaas, S., Chown, T., and B. Volz, "Information Refresh
Time Option for Dynamic Host Configuration Protocol for
IPv6 (DHCPv6)", RFC 4242, November 2005.
11.2. Informative References
[I-D.ietf-v6ops-ipv6-multihoming-without-ipv6nat]
Matsushima, S., Okimoto, T., Troan, O., Miles, D., and D.
Wing, "IPv6 Multihoming without Network Address
Translation",
draft-ietf-v6ops-ipv6-multihoming-without-ipv6nat-04 (work
in progress), February 2012.
[RFC3397] Aboba, B. and S. Cheshire, "Dynamic Host Configuration
Protocol (DHCP) Domain Search Option", RFC 3397,
November 2002.
[RFC3646] Droms, R., "DNS Configuration options for Dynamic Host
Savolainen, et al. Expires November 26, 2012 [Page 22]
Internet-Draft MIF and RDNSS selection May 2012
Configuration Protocol for IPv6 (DHCPv6)", RFC 3646,
December 2003.
[RFC4191] Draves, R. and D. Thaler, "Default Router Preferences and
More-Specific Routes", RFC 4191, November 2005.
[RFC4193] Hinden, R. and B. Haberman, "Unique Local IPv6 Unicast
Addresses", RFC 4193, October 2005.
[RFC6106] Jeong, J., Park, S., Beloeil, L., and S. Madanapalli,
"IPv6 Router Advertisement Options for DNS Configuration",
RFC 6106, November 2010.
[RFC6147] Bagnulo, M., Sullivan, A., Matthews, P., and I. van
Beijnum, "DNS64: DNS Extensions for Network Address
Translation from IPv6 Clients to IPv4 Servers", RFC 6147,
April 2011.
[RFC6418] Blanchet, M. and P. Seite, "Multiple Interfaces and
Provisioning Domains Problem Statement", RFC 6418,
November 2011.
Appendix A. Possible alternative practices for RDNSS selection
On some private namespace deployments explicit policies for RDNSS
selection are not available. This section describes ways for nodes
to mitigate the problem by sending wide-spread queries and by
utilizing possibly existing indirect information elements as hints.
A.1. Sending queries out on multiple interfaces in parallel
A possible current practice is to send DNS queries out of multiple
interfaces and pick up the best out of the received responses. A
node SHOULD implement DNSSEC in order to be able to reject responses
that cannot be validated. Selection between legitimate answers is
implementation specific, but replies from trusted RDNSS should be
preferred.
A downside of this approach is increased consumption of resources.
Namely power consumption if an interface, e.g. wireless, has to be
brought up just for the DNS query that could have been resolved also
via cheaper interface. Also load on RDNSSes is increased. However,
local caching of results mitigates these problems, and a node might
also learn interfaces that seem to be able to provide 'better'
responses than other and prefer those - without forgetting fallback
required for cases when node is connected to more than one network
using private namespaces.
Savolainen, et al. Expires November 26, 2012 [Page 23]
Internet-Draft MIF and RDNSS selection May 2012
A.2. Search list option for DNS forward lookup decisions
A node can learn the special domains of attached network interfaces
from IPv6 Router Advertisement DNS Search List Option [RFC6106] or
DHCP search list options; DHCPv4 Domain Search Option number 119
[RFC3397] and DHCPv6 Domain Search List Option number 24 [RFC3646].
The node behavior is very similar as is illustrated in the example at
Section 5. While these options are not intended to be used in RDNSS
selection, they may be used by the nodes as hints for smarter RDNSS
prioritization purposes in order to increase likelihood of fast and
successful DNS query.
Overloading of existing DNS search list options is not without
problems: resolvers would obviously use the domains learned from
search lists also for name resolution purposes. This may not be a
problem in deployments where DNS search list options contain few
domains like 'example.com, private.example.com', but can become a
problem if many domains are configured.
A.3. More specific routes for reverse lookup decision
[RFC4191] defines how more specific routes can be provisioned for
nodes. This information is not intended to be used in RDNSS
selection, but nevertheless a node can use this information as a hint
about which interface would be best to try first for reverse lookup
procedures. A RDNSS configured via the same interface as more
specific routes is more likely capable to answer reverse lookup
questions correctly than RDNSS of an another interface. The
likelihood of success is possibly higher if RDNSS address is received
in the same RA [RFC6106] as the more specific route information.
A.4. Longest matching prefix for reverse lookup decision
A node may utilize the longest matching prefix approach when deciding
which RDNSS to contact for reverse lookup purposes. Namely, the node
may send a DNS query to a RDNSS learned over an interface having
longest matching prefix to the address being queried. This approach
can help in cases where ULA [RFC4193] addresses are used and when the
queried address belongs to a node or server within the same network
(for example intranet).
Appendix B. DNSSEC and multiple answers validating with different trust
anchors
When validating DNS answers with DNSSEC, a validator might order the
list of trust anchors it uses to start validation chains, in terms of
the node's preferences for those trust anchors. A node could use
Savolainen, et al. Expires November 26, 2012 [Page 24]
Internet-Draft MIF and RDNSS selection May 2012
this ability in order to select among alternative DNS results from
different interfaces. Suppose that a node has a trust anchor for the
public DNS root, and also has a special-purpose trust anchor for
example.com. An answer is received on interface i1 for
www.example.com, and the validation for that succeeds by using the
public trust anchor. Also, an answer is received on interface i2 for
www.example.com, and the validation for that succeeds by using the
trust anchor for example.com. In this case, the node has evidence
for relying on i2 for answers in the example.com zone.
Authors' Addresses
Teemu Savolainen
Nokia
Hermiankatu 12 D
TAMPERE, FI-33720
FINLAND
Email: teemu.savolainen@nokia.com
Jun-ya Kato
NTT
9-11, Midori-Cho 3-Chome Musashino-Shi
TOKYO, 180-8585
JAPAN
Email: kato@syce.net
Ted Lemon
Nominum, Inc.
2000 Seaport Boulevard
Redwood City, CA 94063
USA
Phone: +1 650 381 6000
Email: Ted.Lemon@nominum.com
Savolainen, et al. Expires November 26, 2012 [Page 25]