Network Working Group B. Claise, Ed.
Internet Draft Cisco Systems, Inc.
Obsoletes: 5101 B. Trammell, Ed.
Category: Standards Track ETH Zurich
Expires: September 9, 2012 March 8, 2012
Specification of the IP Flow Information eXport (IPFIX) Protocol
for the Exchange of Flow Information
draft-ietf-ipfix-protocol-rfc5101bis-01
Abstract
This document specifies the IP Flow Information Export (IPFIX)
protocol that serves for transmitting Traffic Flow information over
the network. In order to transmit Traffic Flow information from an
Exporting Process to an information Collecting Process, a common
representation of flow data and a standard means of communicating
them is required. This document describes how the IPFIX Data and
Template Records are carried over a number of transport protocols
from an IPFIX Exporting Process to an IPFIX Collecting Process. This
document obsoletes RFC 5101.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on March 23, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
<Claise, et al.> Standards Track [Page 1]
Internet-Draft IPFIX Protocol Specification March 9, 2012
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1. Changes since RFC 5101 . . . . . . . . . . . . . . . . . . 5
1.2. IPFIX Documents Overview . . . . . . . . . . . . . . . . . 6
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1. Terminology Summary Table . . . . . . . . . . . . . . . . 11
3. IPFIX Message Format . . . . . . . . . . . . . . . . . . . . . 12
3.1. Message Header Format . . . . . . . . . . . . . . . . . . 14
3.2. Field Specifier Format . . . . . . . . . . . . . . . . . . 15
3.3. Set and Set Header Format . . . . . . . . . . . . . . . . 16
3.3.1. Set Format . . . . . . . . . . . . . . . . . . . . . . 16
3.3.2. Set Header Format . . . . . . . . . . . . . . . . . . 17
3.4. Record Format . . . . . . . . . . . . . . . . . . . . . . 18
3.4.1. Template Record Format . . . . . . . . . . . . . . . . 18
3.4.2. Options Template Record Format . . . . . . . . . . . . 20
3.4.2.1. Scope . . . . . . . . . . . . . . . . . . . . . . 21
3.4.2.2. Options Template Record Format . . . . . . . . . . 22
3.4.3. Data Record Format . . . . . . . . . . . . . . . . . . 24
4. Specific Reporting Requirements . . . . . . . . . . . . . . . 25
4.1. The Metering Process Statistics Options Template . . . . . 25
4.2. The Metering Process Reliability Statistics Options
Template . . . . . . . . . . . . . . . . . . . . . . . . . 26
4.3. The Exporting Process Reliability Statistics Options
Template . . . . . . . . . . . . . . . . . . . . . . . . . 28
4.4. The Flow Keys Options Template . . . . . . . . . . . . . . 29
5. IPFIX Message Header Export Time and Flow Record Time . . . . 30
6. Linkage with the Information Model . . . . . . . . . . . . . . 30
6.1. Encoding of IPFIX Data Types . . . . . . . . . . . . . . . 31
6.1.1. Integral Data Types . . . . . . . . . . . . . . . . . . 31
6.1.2. Address Types . . . . . . . . . . . . . . . . . . . . . 31
6.1.3. float32 . . . . . . . . . . . . . . . . . . . . . . . . 31
6.1.4. float64 . . . . . . . . . . . . . . . . . . . . . . . . 31
6.1.5. boolean . . . . . . . . . . . . . . . . . . . . . . . . 31
6.1.6. string and octetArray . . . . . . . . . . . . . . . . . 31
6.1.7. dateTimeSeconds . . . . . . . . . . . . . . . . . . . . 31
6.1.8. dateTimeMilliseconds . . . . . . . . . . . . . . . . . 32
<Claise, et al.> Standards Track [Page 2]
Internet-Draft IPFIX Protocol Specification March 9, 2012
6.1.9 dateTimeMicroseconds . . . . . . . . . . . . . . . . . 32
6.1.10 dateTimeNanoseconds . . . . . . . . . . . . . . . . . . 32
6.2. Reduced Size Encoding of Integer and Float Types . . . . . 33
7. Variable-Length Information Element . . . . . . . . . . . . . 33
8. Template Management . . . . . . . . . . . . . . . . . . . . . 35
8.1. Template Withdrawal and Redefinition . . . . . . . . . . . 36
8.2 Sequencing Template Management Actions . . . . . . . . . . 38
8.3. Additional considerations for Template Management over
SCTP . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
8.4. Additional considerations for Template Management over
UDP . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9. The Collecting Process's Side . . . . . . . . . . . . . . . . . 40
9.1. Additional considerations for SCTP Collecting Processes . 41
9.2. Additional considerations for UDP Collecting Processes . . 41
10. Transport Protocol . . . . . . . . . . . . . . . . . . . . . 41
10.1. Transport Compliance and Transport Usage . . . . . . . . 42
10.2. SCTP . . . . . . . . . . . . . . . . . . . . . . . . . . 42
10.2.1. Congestion Avoidance . . . . . . . . . . . . . . . . 42
10.2.2. Reliability . . . . . . . . . . . . . . . . . . . . . 42
10.2.3. MTU . . . . . . . . . . . . . . . . . . . . . . . . . 43
10.2.4. Association Establishment and Shutdown . . . . . . . 43
10.2.5. Failover . . . . . . . . . . . . . . . . . . . . . . 44
10.2.6. Streams . . . . . . . . . . . . . . . . . . . . . . . 44
10.3. UDP . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
10.3.1. Congestion Avoidance . . . . . . . . . . . . . . . . 44
10.3.2. Reliability . . . . . . . . . . . . . . . . . . . . . 44
10.3.3. MTU . . . . . . . . . . . . . . . . . . . . . . . . . 45
10.3.4. Session Establishment and Shutdown . . . . . . . . . 45
10.3.5. Failover and Session Duplication . . . . . . . . . . 45
10.4. TCP . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10.4.1. Congestion Avoidance . . . . . . . . . . . . . . . . 46
10.4.2. Reliability . . . . . . . . . . . . . . . . . . . . . 47
10.4.3. MTU . . . . . . . . . . . . . . . . . . . . . . . . . 47
10.4.4. Connection Establishment, Shutdown, and Restart . . . 47
10.4.5. Failover . . . . . . . . . . . . . . . . . . . . . . 48
11. Security Considerations . . . . . . . . . . . . . . . . . . . 48
11.1. Applicability of TLS and DTLS . . . . . . . . . . . . . . 49
11.2. Usage . . . . . . . . . . . . . . . . . . . . . . . . . . 50
11.3. Authentication . . . . . . . . . . . . . . . . . . . . . 50
11.4. Protection against DoS Attacks . . . . . . . . . . . . . 51
11.5. When DTLS or TLS Is Not an Option . . . . . . . . . . . . 52
11.6. Logging an IPFIX Attack . . . . . . . . . . . . . . . . . 53
11.7. Securing the Collector . . . . . . . . . . . . . . . . . 53
12. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 53
Appendix A. IPFIX Encoding Examples . . . . . . . . . . . . . . . 54
A.1. Message Header Example . . . . . . . . . . . . . . . . . . 54
A.2. Template Set Examples . . . . . . . . . . . . . . . . . . 55
A.2.1. Template Set Using IETF-Specified Information
<Claise, et al.> Standards Track [Page 3]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Elements . . . . . . . . . . . . . . . . . . . . . . . 55
A.2.2. Template Set Using Enterprise-Specific Information
Elements . . . . . . . . . . . . . . . . . . . . . . . 55
A.3. Data Set Example . . . . . . . . . . . . . . . . . . . . . 57
A.4. Options Template Set Examples . . . . . . . . . . . . . . 58
A.4.1. Options Template Set Using IETF-Specified
Information Elements . . . . . . . . . . . . . . . . . 58
A.4.2. Options Template Set Using Enterprise-Specific
Information . . . . . . . . . . . . . . . . . . . . . 58
A.4.3. Options Template Set Using an Enterprise-Specific
Scope . . . . . . . . . . . . . . . . . . . . . . . . 59
A.4.4. Data Set Using an Enterprise-Specific Scope . . . . . 60
A.5. Variable-Length Information Element Examples . . . . . . . 61
A.5.1. Example of Variable-Length Information Element with
Length . . . . . . . . . . . . . . . . . . . . . . . . 61
A.5.2. Example of Variable-Length Information Element with
3 Octet Length Encoding . . . . . . . . . . . . . . . 61
References . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Normative References . . . . . . . . . . . . . . . . . . . . . . . 61
Informative References . . . . . . . . . . . . . . . . . . . . . . 62
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 64
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 65
OPEN ISSUES:
RFC2026 section 4.1.2: "The requirement for at least two
independent and interoperable implementations applies to all of the
options and features of the specification. In cases in which one or
more options or features have not been demonstrated in at least two
interoperable implementations, the specification may advance to the
Draft Standard level only if those options or features are removed."
The interop report from Prague is at
http://www.ietf.org/proceedings/80/slides/ipfix-4.pdf
The following features have not yet been successfully interop'd; the
document may have to be held pending successful interoperability
testing
1. DTLS over SCTP (section 11.1)
2. DTLS over UDP (section 11.1)
3. multiple-stream export in SCTP (section 10.2.6)
4. Template withdrawal (section 8.1)
5. Template ID reuse (section 8.1)
6. Template stream separation (section 8.3)
7. Template expiration in UDP (section 8.4)
<Claise, et al.> Standards Track [Page 4]
Internet-Draft IPFIX Protocol Specification March 9, 2012
1. Introduction
Traffic on a data network can be seen as consisting of flows passing
through network elements. It is often interesting, useful, or even
necessary to have access to information about these flows that pass
through the network elements for administrative or other purposes. A
collecting process should be able to receive the flow information
passing through multiple network elements within the data network.
This requires uniformity in the method of representing the flow
information and the means of communicating the flows from the network
elements to the collection point. This document specifies a protocol
to achieve these aforementioned requirements. This document specifies
in detail the representation of different flows, the additional data
required for flow interpretation, packet format, transport mechanisms
used, security concerns, etc.
1.1. Changes since RFC 5101
This document obsoletes the Proposed Standard revision of the IPFIX
Protocol Specification [RFC5101]. The protocol specified by this
document is interoperable with the protocol as specified in
[RFC5101]. The following changes have been made to this document with
respect to the previous document:
- EDITOR'S NOTE: not sure if we need to this information
Errata ID: 1655 (technical)
Errata ID: 2791 (technical)
Errata ID: 2814 (editorial)
Errata ID: 1818 (editorial)
Errata ID: 2792 (editorial)
Errata ID: 2888 (editorial)
Errata ID: 2889 (editorial)
Errata ID: 2890 (editorial)
Errata ID: 2891 (editorial)
Errata ID: 2892 (editorial)
Errata ID: 2903 (editorial)
Errata ID: 2761 (editorial)
Errata ID: 2762 (editorial)
Errata ID: 2763 (editorial)
Errata ID: 2764 (editorial)
Errata ID: 2852 (editorial)
Errata ID: 2857 (editorial)
- The encoding of the dateTimeSeconds, dateTimeMilliseconds,
dateTimeMicroseconds, and dateTimeNanoseconds data types, and the
related encoding of the IPFIX Message Header Export Time field, have
been clarified, especially with respect to the epoch upon which the
timestamp data types are based.
<Claise, et al.> Standards Track [Page 5]
Internet-Draft IPFIX Protocol Specification March 9, 2012
- Template management in section 8 has been simplified, and made as
independent of transport protocol as is practically possible, by
relaxing restrictions on template management actions.
- Editorial changes, including structural changes to sections 8, 9,
and 10 to improve readability.
1.2. IPFIX Documents Overview
The IPFIX protocol provides network administrators with access to IP
flow information. The architecture for the export of measured IP
flow information out of an IPFIX Exporting Process to a Collecting
Process is defined in [RFC5470], per the requirements defined in
[RFC3917]. This document specifies how IPFIX data records and
templates are carried via a number of transport protocols from IPFIX
Exporting Processes to IPFIX Collecting Processes.
Four IPFIX optimizations/extensions are currently specified: a
bandwidth saving method for the IPFIX protocol in [RFC5473], an
efficient method for exporting bidirectional flow in [RFC5103], a
method for the definition and export of complex data structures in
[RFC6313], and the specification of the Protocol for IPFIX Mediations
[IPFIX-MED-PROTO] based on the IPIFX Mediation Framework [RFC6183].
IPFIX has a formal description of IPFIX Information Elements, their
name, type and additional semantic information, as specified in
[RFC5102bis], with the export of the Information Element types
specified in [RFC5610].
[IPFIX-CONF] specifies a data model for configuring and monitoring
IPFIX and PSAMP compliant devices using the NETCONF protocol, while
the [RFC5815bis] specifies a MIB module for monitoring.
In terms of development, [RFC5153] provides guidelines for the
implementation and use of the IPFIX protocol, while [RFC5471]
provides guidelines for testing.
Finally, [RFC5472] describes what type of applications can use the
IPFIX protocol and how they can use the information provided. It
furthermore shows how the IPFIX framework relates to other
architectures and frameworks.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
<Claise, et al.> Standards Track [Page 6]
Internet-Draft IPFIX Protocol Specification March 9, 2012
The definitions of the basic terms like Traffic Flow, Exporting
Process, Collecting Process, Observation Points, etc. are
semantically identical to those found in the IPFIX requirements
document [RFC3917]. Some of the terms have been expanded for more
clarity when defining the protocol. Additional terms required for
the protocol have also been defined. Definitions in this document
and in [RFC5470] are equivalent, except that definitions that are
only relevant to the IPFIX protocol only appear here.
The terminology summary table in Section 2.1 gives a quick overview
of the relationships between some of the different terms defined.
Observation Point
An Observation Point is a location in the network where packets
can be observed. Examples include: a line to which a probe is
attached, a shared medium, such as an Ethernet-based LAN, a single
port of a router, or a set of interfaces (physical or logical) of
a router.
Note that every Observation Point is associated with an
Observation Domain (defined below), and that one Observation Point
may be a superset of several other Observation Points. For
example, one Observation Point can be an entire line card. That
would be the superset of the individual Observation Points at the
line card's interfaces.
Observation Domain
An Observation Domain is the largest set of Observation Points for
which Flow information can be aggregated by a Metering Process.
For example, a router line card may be an Observation Domain if it
is composed of several interfaces, each of which is an Observation
Point. In the IPFIX Message it generates, the Observation Domain
includes its Observation Domain ID, which is unique per Exporting
Process. That way, the Collecting Process can identify the
specific Observation Domain from the Exporter that sends the IPFIX
Messages. Every Observation Point is associated with an
Observation Domain. It is RECOMMENDED that Observation Domain IDs
also be unique per IPFIX Device.
Traffic Flow or Flow
There are several definitions of the term 'flow' being used by the
Internet community. Within the context of IPFIX we use the
following definition:
A Flow is defined as a set of packets passing an Observation Point
<Claise, et al.> Standards Track [Page 7]
Internet-Draft IPFIX Protocol Specification March 9, 2012
in the network during a certain time interval. All packets
belonging to a particular Flow have a set of common properties.
Each property is defined as the result of applying a function to
the values of:
1. one or more packet header fields (e.g., destination IP
address), transport header fields (e.g., destination port
number), or application header fields (e.g., RTP header
fields [RFC3550]).
2. one or more characteristics of the packet itself (e.g.,
number of MPLS labels, etc...).
3. one or more of fields derived from packet treatment (e.g.,
next hop IP address, the output interface, etc...).
A packet is defined as belonging to a Flow if it completely
satisfies all the defined properties of the Flow.
This definition covers the range from a Flow containing all
packets observed at a network interface to a Flow consisting of
just a single packet between two applications. It includes
packets selected by a sampling mechanism.
Flow Key
Each of the fields that:
1. belong to the packet header (e.g., destination IP address),
2. are a property of the packet itself (e.g., packet length),
3. are derived from packet treatment (e.g., Autonomous System
(AS) number),
and that are used to define a Flow are termed Flow Keys.
Flow Record
A Flow Record contains information about a specific Flow that was
observed at an Observation Point. A Flow Record contains measured
properties of the Flow (e.g., the total number of bytes for all
the Flow's packets) and usually characteristic properties of the
Flow (e.g., source IP address).
Metering Process
The Metering Process generates Flow Records. Inputs to the
<Claise, et al.> Standards Track [Page 8]
Internet-Draft IPFIX Protocol Specification March 9, 2012
process are packet headers and characteristics observed at an
Observation Point, and packet treatment at the Observation Point
(for example, the selected output interface).
The Metering Process consists of a set of functions that includes
packet header capturing, timestamping, sampling, classifying, and
maintaining Flow Records.
The maintenance of Flow Records may include creating new records,
updating existing ones, computing Flow statistics, deriving
further Flow properties, detecting Flow expiration, passing Flow
Records to the Exporting Process, and deleting Flow Records.
Exporting Process
The Exporting Process sends Flow Records to one or more Collecting
Processes. The Flow Records are generated by one or more Metering
Processes.
Exporter
A device that hosts one or more Exporting Processes is termed an
Exporter.
IPFIX Device
An IPFIX Device hosts at least one Exporting Process. It may host
further Exporting Processes and arbitrary numbers of Observation
Points and Metering Processes.
Collecting Process
A Collecting Process receives Flow Records from one or more
Exporting Processes. The Collecting Process might process or
store received Flow Records, but such actions are out of scope for
this document.
Collector
A device that hosts one or more Collecting Processes is termed a
Collector.
Template
A Template is an ordered sequence of <type, length> pairs used to
completely specify the structure and semantics of a particular set
of information that needs to be communicated from an IPFIX Device
to a Collector. Each Template is uniquely identifiable by means
<Claise, et al.> Standards Track [Page 9]
Internet-Draft IPFIX Protocol Specification March 9, 2012
of a Template ID.
IPFIX Message
An IPFIX Message is a message originating at the Exporting Process
that carries the IPFIX records of this Exporting Process and whose
destination is a Collecting Process. An IPFIX Message is
encapsulated at the transport layer.
Message Header
The Message Header is the first part of an IPFIX Message, which
provides basic information about the message, such as the IPFIX
version, length of the message, message sequence number, etc.
Template Record
A Template Record defines the structure and interpretation of
fields in a Data Record.
Data Record
A Data Record is a record that contains values of the parameters
corresponding to a Template Record.
Options Template Record
An Options Template Record is a Template Record that defines the
structure and interpretation of fields in a Data Record, including
defining how to scope the applicability of the Data Record.
Set
Set is a generic term for a collection of records that have a
similar structure. In an IPFIX Message, one or more Sets follow
the Message Header.
There are three different types of Sets: Template Set, Options
Template Set, and Data Set.
Template Set
A Template Set is a collection of one or more Template Records
that have been grouped together in an IPFIX Message.
Options Template Set
An Options Template Set is a collection of one or more Options
<Claise, et al.> Standards Track [Page 10]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Template Records that have been grouped together in an IPFIX
Message.
Data Set
A Data Set is one or more Data Records, of the same type, that are
grouped together in an IPFIX Message. Each Data Record is
previously defined by a Template Record or an Options Template
Record.
Information Element
An Information Element is a protocol and encoding-independent
description of an attribute that may appear in an IPFIX Record.
The IPFIX information model [RFC5102bis] defines the base set of
Information Elements for IPFIX. The type associated with an
Information Element indicates constraints on what it may contain
and also determines the valid encoding mechanisms for use in
IPFIX.
Transport Session
In Stream Control Transmission Protocol (SCTP), the transport
session is known as the SCTP association, which is uniquely
identified by the SCTP endpoints [RFC4960]; in TCP, the transport
session is known as the TCP connection, which is uniquely
identified by the combination of IP addresses and TCP ports used.
In UDP, the transport session is known as the UDP session, which
is uniquely identified by the combination of IP addresses and UDP
ports used.
2.1. Terminology Summary Table
+------------------+---------------------------------------------+
| | contents |
| +--------------------+------------------------+
| Set | Template | record |
+------------------+--------------------+------------------------+
| Data Set | / | Data Record(s) |
+------------------+--------------------+------------------------+
| Template Set | Template Record(s) | / |
+------------------+--------------------+------------------------+
| Options Template | Options Template | / |
| Set | Record(s) | |
+------------------+--------------------+------------------------+
Figure A: Terminology Summary Table
<Claise, et al.> Standards Track [Page 11]
Internet-Draft IPFIX Protocol Specification March 9, 2012
A Data Set is composed of Data Record(s). No Template Record is
included. A Template Record or an Options Template Record defines
the Data Record.
A Template Set contains only Template Record(s).
An Options Template Set contains only Options Template Record(s).
3. IPFIX Message Format
An IPFIX Message consists of a Message Header, followed by one or
more Sets. The Sets can be any of the possible three types: Data
Set, Template Set, or Options Template Set.
The format of the IPFIX Message is shown in Figure B.
+----------------------------------------------------+
| Message Header |
+----------------------------------------------------+
| Set |
+----------------------------------------------------+
| Set |
+----------------------------------------------------+
...
+----------------------------------------------------+
| Set |
+----------------------------------------------------+
Figure B: IPFIX Message Format
The Exporter MUST code all binary integers of the Message Header and
the different Sets in network-byte order (also known as the
big-endian byte ordering).
Following are some examples of IPFIX Messages:
1. An IPFIX Message consisting of interleaved Template, Data, and
Options Template Sets -- A newly created Template is exported as
soon as possible. So, if there is already an IPFIX Message with a
Data Set that is being prepared for export, the Template and
Options Template Sets are interleaved with this information,
subject to availability of space.
<Claise, et al.> Standards Track [Page 12]
Internet-Draft IPFIX Protocol Specification March 9, 2012
+--------+--------------------------------------------------------+
| | +----------+ +---------+ +-----------+ +---------+ |
|Message | | Template | | Data | | Options | | Data | |
| Header | | Set | | Set | ... | Template | | Set | |
| | | | | | | Set | | | |
| | +----------+ +---------+ +-----------+ +---------+ |
+--------+--------------------------------------------------------+
Figure C: IPFIX Message, Example 1
2. An IPFIX Message consisting entirely of Data Sets -- After the
appropriate Template Records have been defined and transmitted to
the Collecting Process, the majority of IPFIX Messages consist
solely of Data Sets.
+--------+----------------------------------------------+
| | +---------+ +---------+ +---------+ |
|Message | | Data | | Data | | Data | |
| Header | | Set | ... | Set | ... | Set | |
| | +---------+ +---------+ +---------+ |
+--------+----------------------------------------------+
Figure D: IPFIX Message, Example 2
3. An IPFIX Message consisting entirely of Template and Options
Template Sets.
+--------+-------------------------------------------------+
| | +----------+ +----------+ +----------+ |
|Message | | Template | | Template | | Options | |
| Header | | Set | ... | Set | ... | Template | |
| | | | | | | Set | |
| | +----------+ +----------+ +----------+ |
+--------+-------------------------------------------------+
Figure E: IPFIX Message, Example 3
<Claise, et al.> Standards Track [Page 13]
Internet-Draft IPFIX Protocol Specification March 9, 2012
3.1. Message Header Format
The format of the IPFIX Message Header is shown in Figure F.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Version Number | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Export Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Observation Domain ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure F: IPFIX Message Header Format
Message Header Field Descriptions:
Version
Version of Flow Record format exported in this message. The value
of this field is 0x000a for the current version, incrementing by
one the version used in the NetFlow services export version 9
[RFC3954].
Length
Total length of the IPFIX Message, measured in octets, including
Message Header and Set(s).
Export Time
Time at which the IPFIX Message Header leaves the Exporter,
expressed in seconds since the UNIX epoch of 1 January 1970 at
00:00 UTC, encoded as an unsigned 32-bit integer.
Sequence Number
Incremental sequence counter modulo 2^32 of all IPFIX Data Records
sent on this PR-SCTP stream from the current Observation Domain by
the Exporting Process. Check the specific meaning of this field
in the subsections of Section 10 when UDP or TCP is selected as
the transport protocol. This value SHOULD be used by the
Collecting Process to identify whether any IPFIX Data Records have
been missed. Template and Options Template Records do not
increase the Sequence Number.
<Claise, et al.> Standards Track [Page 14]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Observation Domain ID
A 32-bit identifier of the Observation Domain that is locally
unique to the Exporting Process. The Exporting Process uses the
Observation Domain ID to uniquely identify to the Collecting
Process the Observation Domain that metered the Flows. It is
RECOMMENDED that this identifier also be unique per IPFIX Device.
Collecting Processes SHOULD use the Transport Session and the
Observation Domain ID field to separate different export streams
originating from the same Exporter. The Observation Domain ID
SHOULD be 0 when no specific Observation Domain ID is relevant for
the entire IPFIX Message, for example, when exporting the
Exporting Process Statistics, or in case of a hierarchy of
Collectors when aggregated Data Records are exported.
3.2. Field Specifier Format
Vendors need the ability to define proprietary Information Elements,
because, for example, they are delivering a pre-standards product, or
the Information Element is, in some way, commercially sensitive.
This section describes the Field Specifier format for both
IETF-specified Information Elements [RFC5102bis] and enterprise-
specific Information Elements.
The Information Elements are identified by the Information Element
identifier. When the Enterprise bit is set to 0, the corresponding
Information Element identifier will report an IETF-specified
Information Element, and the Enterprise Number MUST NOT be present.
When the Enterprise bit is set to 1, the corresponding Information
Element identifier will report an enterprise-specific Information
Element; the Enterprise Number MUST be present. An example of this
is shown in Section A.4.2.
The Field Specifier format is shown in Figure G.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|E| Information Element ident. | Field Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure G: Field Specifier Format
<Claise, et al.> Standards Track [Page 15]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Where:
E
Enterprise bit. This is the first bit of the Field Specifier.
If this bit is zero, the Information Element Identifier
identifies an IETF-specified Information Element, and the four-
octet Enterprise Number field MUST NOT be present. If this bit is
one, the Information Element identifier identifies an enterprise-
specific Information Element, and the Enterprise Number filed
MUST be present.
Information Element identifier
A numeric value that represents the type of Information Element.
Refer to [RFC5102bis].
Field Length
The length of the corresponding encoded Information Element, in
octets. Refer to [RFC5102bis]. The field length may be smaller
than the definition in [RFC5102bis] if the reduced size encoding
is used (see Section 6.2). The value 65535 is reserved for
variable-length Information Elements (see Section 7).
Enterprise Number
IANA enterprise number [PEN] of the authority defining the
Information Element identifier in this Template Record.
3.3. Set and Set Header Format
A Set is a generic term for a collection of records that have a
similar structure. There are three different types of Sets: Template
Sets, Options Template Sets, and Data Sets. Each of these Sets
consists of a Set Header and one or more records. The Set Format and
the Set Header Format are defined in the following sections.
3.3.1. Set Format
A Set has the format shown in Figure H. The record types can be
either Template Records, Options Template Records, or Data Records.
The record types MUST NOT be mixed within a Set.
<Claise, et al.> Standards Track [Page 16]
Internet-Draft IPFIX Protocol Specification March 9, 2012
+--------------------------------------------------+
| Set Header |
+--------------------------------------------------+
| record |
+--------------------------------------------------+
| record |
+--------------------------------------------------+
...
+--------------------------------------------------+
| record |
+--------------------------------------------------+
| Padding (opt.) |
+--------------------------------------------------+
Figure H: Set Format
The Set Field Definitions are as follows:
Set Header
The Set Header Format is defined in Section 3.3.2.
Record
One of the record Formats: Template Record, Options Template
Record, or Data Record Format.
Padding
The Exporting Process MAY insert some padding octets, so that the
subsequent Set starts at an aligned boundary. For security
reasons, the padding octet(s) MUST be composed of zero (0) valued
octets. The padding length MUST be shorter than any allowable
record in this Set. If padding of the IPFIX Message is desired in
combination with very short records, then the padding Information
Element 'paddingOctets' [RFC5102bis] can be used for padding
records such that their length is increased to a multiple of 4 or
8 octets. Because Template Sets are always 4-octet aligned by
definition, padding is only needed in case of other alignments
e.g., on 8-octet boundaries.
3.3.2. Set Header Format
Every Set contains a common header. This header is defined in Figure
I.
<Claise, et al.> Standards Track [Page 17]
Internet-Draft IPFIX Protocol Specification March 9, 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure I: Set Header Format
The Set Header Field Definitions are as follows:
Set ID
Set ID value identifies the Set. A value of 2 is reserved for the
Template Set. A value of 3 is reserved for the Options Template
Set. All other values from 4 to 255 are reserved for future use.
Values above 255 are used for Data Sets. The Set ID values of 0
and 1 are not used for historical reasons [RFC3954].
Length
Total length of the Set, in octets, including the Set Header, all
records, and the optional padding. Because an individual Set MAY
contain multiple records, the Length value MUST be used to
determine the position of the next Set.
3.4. Record Format
IPFIX defines three record formats, defined in the next sections: the
Template Record Format, the Options Template Record Format, and the
Data Record Format.
3.4.1. Template Record Format
One of the essential elements in the IPFIX record format is the
Template Record. Templates greatly enhance the flexibility of the
record format because they allow the Collecting Process to process
IPFIX Messages without necessarily knowing the interpretation of all
Data Records. A Template Record contains any combination of
IANA-assigned and/or enterprise-specific Information Elements
identifiers.
The format of the Template Record is shown in Figure J. It consists
of a Template Record Header and one or more Field Specifiers. The
definition of the Field Specifiers is given in Figure G above.
<Claise, et al.> Standards Track [Page 18]
Internet-Draft IPFIX Protocol Specification March 9, 2012
+--------------------------------------------------+
| Template Record Header |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
...
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
Figure J: Template Record Format
The format of the Template Record Header is shown in Figure K.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID (> 255) | Field Count |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure K: Template Record Header Format
The Template Record Header Field Definitions are as follows:
Template ID
Each of the newly generated Template Records is given a unique
Template ID. This uniqueness is local to the Transport Session
and Observation Domain that generated the Template ID. Template
IDs 0-255 are reserved for Template Sets, Options Template Sets,
and other reserved Sets yet to be created. Template IDs of Data
Sets are numbered from 256 to 65535. There are no constraints
regarding the order of the Template ID allocation.
Field Count
Number of fields in this Template Record.
The example in Figure L shows a Template Set with mixed standard and
enterprise-specific Information Elements. It consists of a Set
Header, a Template Header, and several Field Specifiers.
<Claise, et al.> Standards Track [Page 19]
Internet-Draft IPFIX Protocol Specification March 9, 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 256 | Field Count = N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element id. 1.1 | Field Length 1.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 1.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Information Element id. 1.2 | Field Length 1.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element id. 1.N | Field Length 1.N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 1.N |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 257 | Field Count = M |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| Information Element id. 2.1 | Field Length 2.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element id. 2.2 | Field Length 2.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 2.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element id. 2.M | Field Length 2.M |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise Number 2.M |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Padding (opt) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure L: Template Set Example
Information Element Identifiers 1.2 and 2.1 are defined by the IETF
(Enterprise bit = 0) and, therefore, do not need an Enterprise Number
to identify them.
3.4.2. Options Template Record Format
Thanks to the notion of scope, The Options Template Record gives the
Exporter the ability to provide additional information to the
Collector that would not be possible with Flow Records alone.
<Claise, et al.> Standards Track [Page 20]
Internet-Draft IPFIX Protocol Specification March 9, 2012
One Options Template Record example is the "Flow Keys", which reports
the Flow Keys for a Template, which is defined as the scope. Another
example is the "Template configuration", which reports the
configuration sampling parameter(s) for the Template, which is
defined as the scope.
3.4.2.1. Scope
The scope, which is only available in the Options Template Set, gives
the context of the reported Information Elements in the Data Records.
Note that the IPFIX Message Header already contains the Observation
Domain ID (the identifier of the Observation Domain). If not zero,
this Observation Domain ID can be considered as an implicit scope for
the Data Records in the IPFIX Message. The Observation Domain ID
MUST be zero when the IPFIX Message contains Data Records with
different Observation Domain ID values defined as scopes.
Multiple Scope Fields MAY be present in the Options Template Record,
in which case, the composite scope is the combination of the scopes.
For example, if the two scopes are defined as "metering process" and
"template", the combined scope is this Template for this Metering
Process. The order of the Scope Fields, as defined in the Options
Template Record, is irrelevant in this case. However, if the order
of the Scope Fields in the Options Template Record is relevant, the
order of the Scope Fields MUST be used. For example, if the first
scope defines the filtering function, while the second scope defines
the sampling function, the order of the scope is important. Applying
the sampling function first, followed by the filtering function,
would lead to potentially different Data Records than applying the
filtering function first, followed by the sampling function. In this
case, the Collector deduces the function order by looking at the
order of the scope in the Options Template Record.
The scope is an Information Element specified in the IPFIX
Information Model [RFC5102bis]. An IPFIX-compliant implementation of
the Collecting Process SHOULD support this minimum set of Information
Elements as scope: LineCardId, TemplateId, exporterIPv4Address,
exporterIPv6Address, and ingressInterface. Note that other
Information Elements, such as meteringProcessId, exportingProcessId,
observationDomainId, etc. are also valid scopes. The IPFIX protocol
doesn't prevent the use of any Information Elements for scope.
However, some Information Element types don't make sense if specified
as scope; for example, the counter Information Elements.
Finally, note that the Scope Field Count MUST NOT be zero.
<Claise, et al.> Standards Track [Page 21]
Internet-Draft IPFIX Protocol Specification March 9, 2012
3.4.2.2. Options Template Record Format
An Options Template Record contains any combination of IANA-assigned
and/or enterprise-specific Information Elements identifiers.
The format of the Options Template Record is shown in Figure M. It
consists of an Options Template Record Header and one or more Field
Specifiers. The definition of the Field Specifiers is given in
Figure G above.
+--------------------------------------------------+
| Options Template Record Header |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
...
+--------------------------------------------------+
| Field Specifier |
+--------------------------------------------------+
Figure M: Options Template Record Format
The format of the Options Template Record Header is shown in Figure
N.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID (> 255) | Field Count |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure N: Options Template Record Header Format
The Options Template Record Header Field Definitions are as follows:
Template ID
Template ID of this Options Template Record. This value is greater
than 255.
<Claise, et al.> Standards Track [Page 22]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Field Count
Number of all fields in this Options Template Record, including the
Scope Fields.
Scope Field Count
Number of scope fields in this Options Template Record. The Scope
Fields are normal Fields except that they are interpreted as scope at
the Collector. The Scope Field Count MUST NOT be zero.
The example in Figure O shows an Options Template Set with mixed IETF
and enterprise-specific Information Elements. It consists of a Set
Header, an Options Template Header, and several Field Specifiers.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 258 | Field Count = N + M |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = N |0| Scope 1 Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length |0| Scope 2 Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 2 Field Length | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |1| Scope N Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope N Field Length | Scope N Enterprise Number ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Scope N Enterprise Number |1| Option 1 Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option 1 Field Length | Option 1 Enterprise Number ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Option 1 Enterprise Number | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |0| Option M Infor. Element Id. |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option M Field Length | Padding (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure O: Options Template Set Example
<Claise, et al.> Standards Track [Page 23]
Internet-Draft IPFIX Protocol Specification March 9, 2012
3.4.3. Data Record Format
The Data Records are sent in Data Sets. The format of the Data
Record is shown in Figure P. It consists only of one or more Field
Values. The Template ID to which the Field Values belong is encoded
in the Set Header field "Set ID", i.e., "Set ID" = "Template ID".
+--------------------------------------------------+
| Field Value |
+--------------------------------------------------+
| Field Value |
+--------------------------------------------------+
...
+--------------------------------------------------+
| Field Value |
+--------------------------------------------------+
Figure P: Data Record Format
Note that Field Values do not necessarily have a length of 16 bits.
Field Values are encoded according to their data type specified in
[RFC5102bis].
Interpretation of the Data Record format can be done only if the
Template Record corresponding to the Template ID is available at the
Collecting Process.
The example in Figure Q shows a Data Set. It consists of a Set Header
and several Field Values.
<Claise, et al.> Standards Track [Page 24]
Internet-Draft IPFIX Protocol Specification March 9, 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = Template ID | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 1 - Field Value 1 | Record 1 - Field Value 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 1 - Field Value 3 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 2 - Field Value 1 | Record 2 - Field Value 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 2 - Field Value 3 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 3 - Field Value 1 | Record 3 - Field Value 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Record 3 - Field Value 3 | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... | Padding (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure Q: Data Set, Containing Data Records
4. Specific Reporting Requirements
Some specific Options Templates and Options Template Records are
necessary to provide extra information about the Flow Records and
about the Metering Process.
The Options Template and Options Template Records defined in these
subsections, which impose some constraints on the Metering Process
and Exporting Process implementations, MAY be implemented. If
implemented, the specific Options Templates SHOULD be implemented as
specified in these subsections.
The minimum set of Information Elements is always specified in these
Specific IPFIX Options Templates. Nevertheless, extra Information
Elements may be used in these specific Options Templates.
The Collecting Process MUST check the possible combinations of
Information Elements within the Options Template Records to correctly
interpret the following Options Templates.
4.1. The Metering Process Statistics Options Template
The Metering Process Statistics Options Template specifies the
structure of a Data Record for reporting Metering Process statistics.
It SHOULD contain the following Information Elements that are
defined in [RFC5102bis]:
<Claise, et al.> Standards Track [Page 25]
Internet-Draft IPFIX Protocol Specification March 9, 2012
(scope) observationDomainId
An identifier of an Observation Domain that
is locally unique to the Exporting Process.
This Information Element MUST be defined as a
Scope Field.
(scope) meteringProcessId
An identifier of the Metering Process for
which statistics are reported. This
Information Element MUST be defined as a
Scope Field.
exportedMessageTotalCount
The total number of IPFIX Messages that the
Exporting Process successfully sent to the
Collecting Process since the Exporting
Process re-initialization.
exportedFlowRecordTotalCount
The total number of Flow Records that the
Exporting Process successfully sent to the
Collecting Process since the Exporting
Process re-initialization.
exportedOctetTotalCount
The total number of octets that the Exporting
Process successfully sent to the Collecting
Process since the Exporting Process re-
initialization.
The Exporting Process SHOULD export the Data Record specified by the
Metering Process Statistics Options Template on a regular basis or
based on some export policy. This periodicity or export policy
SHOULD be configurable.
Note that if several Metering Processes are available on the Exporter
Observation Domain, the Information Element meteringProcessId MUST be
specified as an additional Scope Field.
4.2. The Metering Process Reliability Statistics Options Template
The Metering Process Reliability Options Template specifies the
structure of a Data Record for reporting lack of reliability in the
Metering Process. It SHOULD contain the following Information
Elements that are defined in [RFC5102bis]:
<Claise, et al.> Standards Track [Page 26]
Internet-Draft IPFIX Protocol Specification March 9, 2012
(scope) observationDomainId
An identifier of an Observation Domain that
is locally unique to the Exporting Process.
This Information Element MUST be defined as a
Scope Field.
(scope) meteringProcessId
The identifier of the Metering Process for
which lack of reliability is reported. This
Information Element MUST be defined as a
Scope Field.
ignoredPacketTotalCount
The total number of IP packets that the
Metering Process did not process.
ignoredOctetTotalCount
The total number of octets in observed
packets that the Metering Process did not
process.
time first packet ignored
The timestamp of the first packet that was
ignored by the Metering Process. For this
timestamp, any of the following timestamp can
be used: observationTimeSeconds,
observationTimeMilliseconds,
observationTimeMicroseconds, or
observationTimeNanoseconds.
time last packet ignored
The timestamp of the last packet that was
ignored by the Metering Process. For this
timestamp, any of the following timestamp can
be used: observationTimeSeconds,
observationTimeMilliseconds,
observationTimeMicroseconds, or
observationTimeNanoseconds.
The Exporting Process SHOULD export the Data Record specified by the
Metering Process Reliability Statistics Options Template on a regular
basis or based on some export policy. This periodicity or export
policy SHOULD be configurable.
Note that if several Metering Processes are available on the Exporter
Observation Domain, the Information Element meteringProcessId MUST be
specified as an additional Scope Field.
<Claise, et al.> Standards Track [Page 27]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Since the Metering Process Reliability Option Template will logically
contain two identical timestamp Information Elements, and since the
order of the Information Elements in the Template Records is not
guaranteed, the Collecting Process MUST determine which is the oldest
and the most recent timestamp in order the determine the right
semantic behind the time first packet ignored and time last packet
ignored Information Elements. Note that the counters wrap-around for
the timestamps SHOULD also be taken into account.
4.3. The Exporting Process Reliability Statistics Options Template
The Exporting Process Reliability Options Template specifies the
structure of a Data Record for reporting lack of reliability in the
Exporting process. It SHOULD contain the following Information
Elements that are defined in [RFC5102bis]:
(scope) Exporting Process ID
The identifier of the Exporting Process for
which lack of reliability is reported. There
are three Information Elements specified in
[RFC5102bis] that can be used for this purpose:
exporterIPv4Address, exporterIPv6Address, or
exportingProcessId. This Information Element
MUST be defined as a Scope Field.
notSentFlowTotalCount
The total number of Flows that were generated by
the Metering Process and dropped by the Metering
Process or by the Exporting Process instead of
being sent to the Collecting Process.
notSentPacketTotalCount
The total number of packets in Flow Records that
were generated by the Metering Process and
dropped by the Metering Process or by the
Exporting Process instead of being sent to the
Collecting Process.
notSentOctetTotalCount
The total number of octets in packets in Flow
Records that were generated by the Metering
Process and dropped by the Metering Process or
by the Exporting Process instead of being sent
to the Collecting Process.
<Claise, et al.> Standards Track [Page 28]
Internet-Draft IPFIX Protocol Specification March 9, 2012
time first flow dropped
The time at which the first Flow Record was
dropped by the Exporting Process. For this
timestamp, any of the following timestamp can be
used: observationTimeSeconds,
observationTimeMilliseconds,
observationTimeMicroseconds, or
observationTimeNanoseconds.
time last flow dropped
The time at which the last Flow Record was
dropped by the Exporting Process. For this
timestamp, any of the following timestamp can be
used: observationTimeSeconds,
observationTimeMilliseconds,
observationTimeMicroseconds, or
observationTimeNanoseconds.
The Exporting Process SHOULD export the Data Record specified by the
Exporting Process Reliability Statistics Options Template on a
regular basis or based on some export policy. This periodicity or
export policy SHOULD be configurable.
Since the Exporting Process Reliability Option Template will
logically contain two identical timestamp Information Elements, and
since the order of the Information Elements in the Template Records
is not guaranteed, the Collecting Process MUST determine which is the
oldest and the most recent timestamp in order the determine the right
semantic behind the time first packet ignored and time last packet
ignored Information Elements. Note that the counters wrap-around for
the timestamps SHOULD also be taken into account.
4.4. The Flow Keys Options Template
The Flow Keys Options Template specifies the structure of a Data
Record for reporting the Flow Keys of reported Flows. A Flow Keys
Data Record extends a particular Template Record that is referenced
by its templateId identifier. The Template Record is extended by
specifying which of the Information Elements contained in the
corresponding Data Records describe Flow properties that serve as
Flow Keys of the reported Flow.
The Flow Keys Options Template SHOULD contain the following
Information Elements that are defined in [RFC5102bis]:
<Claise, et al.> Standards Track [Page 29]
Internet-Draft IPFIX Protocol Specification March 9, 2012
(scope) templateId An identifier of a Template. This
Information Element MUST be defined as a
Scope Field.
flowKeyIndicator Bitmap with the positions of the Flow Keys in
the Data Records.
5. IPFIX Message Header Export Time and Flow Record Time
The IPFIX Message Header Export Time field is the time at which the
IPFIX Message Header leaves the Exporter, expressed in seconds since
the UNIX epoch, 1 January 1970 at 00:00 UTC, encoded in an unsigned
32-bit integer.
Certain time-related Information Elements may be expressed as an
offset from this Export Time. For example, Data Records requiring a
microsecond precision can export the flow start and end times with
the flowStartMicroseconds and flowEndMicroseconds Information
Elements [RFC5102bis], which encode the absolute time in microseconds
in terms of the NTP epoch, 1 January 1900 at 00:00 UTC, in a 64-bit
field. An alternate solution is to export the
flowStartDeltaMicroseconds and flowEndDeltaMicroseconds Information
Elements [RFC5102bis] in the Data Record, which respectively report
the flow start and end time as negative offsets from the Export Time,
as an unsigned 32-bit integer. This latter solution lowers the export
bandwidth requirement, saving two bytes per timestamp, while
increasing the load on the Exporter, as the Exporting Process must
calculate the flowStartDeltaMicroseconds and flowEndDeltaMicroseconds
of every single Data Record before exporting the IPFIX Message.
It must be noted that timestamps based on the Export Time impose some
time constraints on the Data Records contained within the IPFIX
Message. In the example of flowStartDeltaMicroseconds and
flowEndDeltaMicroseconds Information Elements [RFC5102bis], the Data
Record can only contain records with timestamps within 71 minutes of
the Export Time. Otherwise, the 32-bit counter would not be
sufficient to contain the flow start time offset.
6. Linkage with the Information Model
The Information Elements [RFC5102bis] MUST be sent in canonical
format in network-byte order (also known as the big-endian byte
ordering).
<Claise, et al.> Standards Track [Page 30]
Internet-Draft IPFIX Protocol Specification March 9, 2012
6.1. Encoding of IPFIX Data Types
The following sections will define the encoding of the data types
specified in [RFC5102bis].
6.1.1. Integral Data Types
Integral data types -- octet, signed8, unsigned16, signed16,
unsigned32, signed32, signed64, and unsigned64 -- MUST be encoded
using the default canonical format in network-byte order. Signed
Integral data types are represented in two's complement notation.
6.1.2. Address Types
Address types -- macAddress, ipv4Address, and ipv6Address -- MUST be
encoded the same way as the integral data types. The macAddress is
treated as a 6-octet integer, the ipv4Address as a 4-octet integer,
and the ipv6Address as a 16-octet integer.
6.1.3. float32
The float32 data type MUST be encoded as an IEEE single-precision
32-bit floating point-type, as specified in [IEEE.754.1985].
6.1.4. float64
The float64 data type MUST be encoded as an IEEE double-precision 64-
bit floating point-type, as specified in [IEEE.754.1985].
6.1.5. boolean
The boolean data type is specified according to the TruthValue in
[RFC2579]: it is an integer with the value 1 for true and a value 2
for false. Every other value is undefined. The boolean data type
MUST be encoded in a single octet.
6.1.6. string and octetArray
The data type string represents a finite length string of valid
characters of the Unicode character encoding set. The string data
type MUST be encoded in UTF-8 format. The string is sent as an array
of octets using an Information Element of fixed or variable length.
The length of the Information Element specifies the length of the
octetArray.
6.1.7. dateTimeSeconds
The data type dateTimeSeconds is an unsigned 32 bit integer
<Claise, et al.> Standards Track [Page 31]
Internet-Draft IPFIX Protocol Specification March 9, 2012
containing the number of seconds since the UNIX epoch, 1 January 1970
at 00:00 UTC, as defined in [POSIX.1]. dateTimeSeconds is encoded
identically to the IPFIX Message Header Export Time field. It can
represent dates between 1 January 1970 and 8 February 2106.
6.1.8. dateTimeMilliseconds
The data type dateTimeMilliseconds is an unsigned 64-bit integer
containing the number of milliseconds since the UNIX epoch, 1 January
1970 at 00:00 UTC, as defined in [POSIX.1]. It can represent dates
beginning on 1 January 1970 for approximately the next 500 billion
years.
6.1.9 dateTimeMicroseconds
The data type dateTimeMicroseconds is a 64-bit field encoded
according to the NTP Timestamp format as defined in section 6 of
[RFC5905]. This field is made up of two unsigned 32-bit integers,
Seconds and Fraction. The Seconds field is the number of seconds
since the NTP epoch, 1 January 1900 at 00:00 UTC. The Fraction field
is the fractional number of seconds in units of 1/(2^32) seconds
(approximately 233 picoseconds). It can represent dates beginning
between 1 January 1900 and 8 February 2036.
Note that dateTimeMicroseconds and dateTimeNanoseconds share an
identical encoding. The dataTimeMicroseconds data type is intended
only to represent timestamps of microsecond precision. Therefore, the
bottom 11 bits of the fraction field MAY contain any value and MUST
be ignored for all Information Elements of this data type (as 2^11 x
233 picoseconds = .477 microseconds).
6.1.10 dateTimeNanoseconds
The data type dateTimeNanoseconds is a 64-bit field encoded according
to the NTP Timestamp format as defined in section 6 of [RFC5905].
This field is made up of two unsigned 32-bit integers, Seconds and
Fraction. The Seconds field is the number of seconds since the NTP
epoch, 1 January 1900 at 00:00 UTC. The Fraction field is the
fractional number of seconds in units of 1/(2^32) seconds
(approximately 233 picoseconds). It can represent dates beginning
between 1 January 1900 and 8 February 2036.
Note that dateTimeMicroseconds and dateTimeNanoseconds share an
identical encoding. There is no restriction on the interpretation of
the Fraction field for the dateTimeNanoseconds data type.
<Claise, et al.> Standards Track [Page 32]
Internet-Draft IPFIX Protocol Specification March 9, 2012
6.2. Reduced Size Encoding of Integer and Float Types
Information Elements containing integer, string, float, and
octetArray types in the information model MAY be encoded using fewer
octets than those implied by their type in the information model
definition [RFC5102bis], based on the assumption that the smaller
size is sufficient to carry any value the Exporter may need to
deliver. This reduces the network bandwidth requirement between the
Exporter and the Collector. Note that the Information Element
definitions [RFC5102bis] will always define the maximum encoding
size.
For instance, the information model [RFC5102bis] defines byteCount as
an unsigned64 type, which would require 64 bits. However, if the
Exporter will never locally encounter the need to send a value larger
than 4294967295, it may chose to send the value instead as an
unsigned32. For example, a core router would require an unsigned64
byteCount, while an unsigned32 might be sufficient for an access
router.
This behavior is indicated by the Exporter by specifying a type size
with a smaller length than that associated with the assigned type of
the Information Element. In the example above, the Exporter would
place a length of 4 versus 8 in the Template.
If reduced size encoding is used, it MUST only be applied to the
following integer types: unsigned64, signed64, unsigned32, signed32,
unsigned16, and signed16. The signed versus unsigned property of the
reported value MUST be preserved. The reduction in size can be to
any number of octets smaller than the original type if the data value
still fits, i.e., so that only leading zeroes are dropped. For
example, an unsigned64 can be reduced in size to 7, 6, 5, 4, 3, 2, or
1 octet(s).
Reduced size encoding can also be used to reduce float64 to float32.
The float32 not only has a reduced number range, but due to the
smaller mantissa, is also less precise.
The reduced size encoding MUST NOT be applied to dateTimeMicroseconds
or to dateTimeNanoseconds because these represent an inherent
structure that would be destroyed by using less than the original
number of bytes.
7. Variable-Length Information Element
The IPFIX Template mechanism is optimized for fixed-length
Information Elements [RFC5102bis]. Where an Information Element has
a variable length, the following mechanism MUST be used to carry the
<Claise, et al.> Standards Track [Page 33]
Internet-Draft IPFIX Protocol Specification March 9, 2012
length information for both the IETF and proprietary Information
Elements.
In the Template Set, the Information Element Field Length is recorded
as 65535. This reserved length value notifies the Collecting Process
that length of the Information Element will be carried in the
Information Element content itself.
In most cases, the length of the Information Element will be less
than 255 octets. The following length-encoding mechanism optimizes
the overhead of carrying the Information Element length in this
majority case. The length is carried in the octet before the
Information Element, as shown in Figure R.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length (< 255)| Information Element |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... continuing as needed |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure R: Variable-Length Information Element (length < 255 octets)
The length may also be encoded into 3 octets before the Information
element allowing the length of the Information Element to be greater
than or equal to 255 octets. In this case, first octet of the Length
field MUST be 255, and the length is carried in the second and third
octets, as shown in Figure S.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 255 | Length (0 to 65535) | IE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... continuing as needed |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure S: Variable-Length Information Element (length 0 to 65535
octets)
The octets carrying the length (either the first or the first three
octets) MUST NOT be included in the length of the Information
Element.
<Claise, et al.> Standards Track [Page 34]
Internet-Draft IPFIX Protocol Specification March 9, 2012
8. Template Management
This section describes the management of Templates and Options
Templates at the Exporting and Collecting Processes. The goal of
Template management is to ensure, to the extent possible, that the
Exporting Process and Collecting Process have a consistent view of
the Templates and Options Templates used to encode and decode the
Records sent from the Exporting Process to the Collecting Process.
Achieving this goal is complicated somewhat by two factors: 1. the
need to support the reuse of Template IDs within a Transport Session
and 2. the need to support unreliable transmission for templates when
UDP is used as the transport protocol for IPFIX Messages.
The Template Management mechanisms defined in this section apply to
IPFIX Message export on any supported Transport Protocol. Additional
considerations specific to SCTP and UDP transport are given in
sections 8.3 and 8.4, respectively.
The Exporting Process assigns and maintains the Template IDs per
Transport Session for the Exporter's Observation Domains. A newly
created Template Record is assigned an unused Template ID by the
Exporting Process. The Collecting Process MUST store the Template
Record information for the duration of each Transport Session until
reuse or withdrawal as in section 8.1, except as noted in section
8.4, so that it can interpret the corresponding Data Records that are
received in subsequent Data Sets. The Collecting Process MUST NOT
assume that the Template IDs from a given Exporting Process refer to
the same Templates as they did in previous Transport Sessions from
the same Exporting Process. When a Transport Session is closed, the
Collecting Process MUST discard all Templates received over that
association and stop decoding IPFIX Messages that use those
Templates.
If a specific Information Element is required by a Template, but is
not present in observed packets, the Exporting Process MAY choose to
export Flow Records without this Information Element in a Data Record
defined by a new Template.
If an Information Element is required more than once in a Template,
the different occurrences of this Information Element SHOULD follow
the logical order of their treatments by the Metering Process. For
example, if a selected packet goes through two hash functions, and if
the two hash values are sent within a single Template, the first
occurrence of the hash value should belong to the first hash function
in the Metering Process. For example, when exporting the two source
IP addresses of an IPv4 in IPv4 packets, the first sourceIPv4Address
Information Element occurrence should be the IPv4 address of the
outer header, while the second occurrence should be the address of
<Claise, et al.> Standards Track [Page 35]
Internet-Draft IPFIX Protocol Specification March 9, 2012
the inner header. Collecting processes MUST properly handle Templates
with multiple identical Information Elements.
The Exporting Process SHOULD transmit the Template Set and Options
Template Set in advance of any Data Sets that use that (Options)
Template ID, to help ensure that the Collector has the Template
Record before receiving the first Data Record. Data Records that
correspond to a Template Record MAY appear in the same and/or
subsequent IPFIX Message(s).
This ensures that the Collecting Process normally receives Template
Records from the Exporting Process before receiving Data Records.
However, if the Template Records have not been received at the time
Data Records are received, the Collecting Process MAY store the Data
Records for a short period of time and decode them after the Template
Records are received. In any case, a Collecting Process MUST NOT
assume that the Data Set and the associated Template Set (or Options
Template Set) are exported in the same IPFIX Message.
Different Observation Domains from the same Transport Session MAY use
the same Template ID value to refer to different Templates;
Collecting Processes MUST properly handle this case.
Options Templates and Templates which are related or interdependent
(e.g. by sharing common properties as in [RFC5473]) SHOULD be sent
together in the same IPFIX Message.
8.1. Template Withdrawal and Redefinition
Since a Template may have a lifetime at the Exporting Process
independent of the Transport Session, IPFIX provides a mechanism for
the withdrawal of templates and for the reuse of template IDs.
Templates that will not be used further by an Exporting Process
SHOULD be withdrawn by sending a Template Withdrawal Message. After
receiving a Template Withdrawal, a Collecting Process MUST discard
the Template and stop using it to interpret Data Sets.
A Template Withdrawal consists of a Template Record for the Template
ID to be with a Field Count of 0. The format of a Template
Withdrawal is shown in Figure T.
<Claise, et al.> Standards Track [Page 36]
Internet-Draft IPFIX Protocol Specification March 9, 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = (2 or 3) | Length = 16 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID N | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID ... | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID M | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure T: Template Withdrawal Set Format
The Set ID field MUST contain the value 2 for Template Set Withdrawal
and the value 3 for Options Template Set Withdrawal. Multiple
Template IDs MAY be withdrawn with a single Template Withdrawal, in
that case, padding MAY be used.
A Template Withdrawal Message is an IPFIX Message containing Template
Withdrawals. It withdraws Template IDs for the Observation Domain ID
specified in the IPFIX Message Header. It MUST NOT contain new
Template or Options Template Records, or any Data Sets. The Exporting
Process SHOULD NOT send a Template Withdrawal Message until
sufficient time has elapsed to allow receipt and processing of and
Data Records described by the withdrawn Templates; see section 8.2
for more information on sequencing Template Withdrawals.
The end of a Transport Session implicitly withdraws all the Templates
used within the Transport Session, and Templates must be resent
during subsequent Transport Sessions between an Exporting Process and
Collecting Process. All Templates for a given Observation Domain MAY
also be withdrawn using an All Templates Withdrawal, which withdraws
the special Template ID 2; this is shown in Figure U. All Options
Templates for a given observation Domain MAY likewise be withdrawn
using an All Options Templates Withdrawal, which withdraws the
special Template ID 3. Each of these Withdrawals MUST appear in a
Template Withdrawal Message with no other Withdrawals.
<Claise, et al.> Standards Track [Page 37]
Internet-Draft IPFIX Protocol Specification March 9, 2012
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 2 | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure U: All Templates Withdrawal Set Format
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 8 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID = 3 | Field Count = 0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure V: All Options Templates Withdrawal Set Format
Template IDs MAY be reused for new Templates by sending a new
Template Record or Options Template Record for a given Template ID.
The Template ID MAY be withdrawn beforehand using a Template
Withdrawal, as above. However, if an Exporting Process sends a new
Template or Options Template for an already-allocated Template ID,
the new Template replaces the old Template with immediate effect; see
section 8.2 for information on sequencing template ID reuse. As the
reuse of a Template ID by a different Template with a short delay
(i.e., less than the configured retransmit delay for UDP) might
indicate a misconfiguration; such reuse SHOULD be logged by the
Collecting Process.
If a Collecting Process receives a Template Withdrawal for a Template
or Options Template it does not presently have stored, it MUST ignore
the Template Withdrawal and SHOULD log the error.
8.2 Sequencing Template Management Actions
The Exporting Process MUST ensure that the sending of Templates,
Template Withdrawals, and reuse of Template IDs is consistent in time
with respect to the Data Records described by those Templates as
sequenced using the Export Time field in the Message Header of the
Messages containing said Templates, Template Withdrawals, and Data
Records.
Put another way, a Template only describes Records contained in IPFIX
<Claise, et al.> Standards Track [Page 38]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Messages with the same Export Time as the IPFIX Message containing
Template Record, or a subsequent export time. Likewise, a Template
Withdrawal is only in effect for IPFIX Messages with the same Export
Time as the Template Withdrawal, or a subsequent Export Time.
Exporting Processes SHOULD ensure that IPFIX Messages are sent in
Export Time order to assist in sequencing of Template management
events. Collecting Processes MAY implement a buffer to handle out-of-
order Template management events.
8.3. Additional considerations for Template Management over SCTP
Template Sets and Options Template Sets MAY be sent on any SCTP
stream. Data Sets sent on a given SCTP stream MAY be represented by
Template Records exported on any SCTP stream.
Template Sets and Options Template Sets MUST be sent reliably and in
order.
Template Withdrawal Messages may be sent on any SCTP stream. Template
Withdrawal Messages MUST be sent reliably, using SCTP-ordered
delivery. Template IDs MAY be reused by sending a Template Withdrawal
Message and/or a new Template Record on a different SCTP stream than
the stream on which the original Template was sent.
Additional Template Management considerations are given in [IPFIX-
PER-SCTP-STREAM], which specifies an extension to explicitly link
Templates with SCTP streams. In exchange for more restrictive rules
on the assignment of Template Records to SCTP streams, this extension
allows fast, reliable reuse of Template IDs and estimation of Data
Record loss per Template.
8.4. Additional considerations for Template Management over UDP
Since UDP provides no method for reliable transmission of Templates,
Exporting Processes using UDP as the Transport Protocol MUST
periodically retransmit each active Template at regular intervals.
The template retransmission interval MUST be configurable, as via the
the templateRefreshTimeout and optionsTemplateRefreshTimeout defined
in [IPFIX-CONF]. Default settings for these values are deployment-
and application-specific.
Before exporting any Data Records described by a given Template
Record or Options Template Record, especially in the case of Template
ID reuse as in section 8.1, the Exporting Process SHOULD send
multiple copies of the Template Record in separate IPFIX Message, in
order to help ensure the Collecting Process has received it.
<Claise, et al.> Standards Track [Page 39]
Internet-Draft IPFIX Protocol Specification March 9, 2012
In order to minimize resource requirements for templates which have
expired at the Exporting Process without being withdrawn, or in cases
when the Template Withdrawal Message was lost between the Exporting
Process and the Collecting Process, the Collecting Process MAY
associate a lifetime with each Template received in a UDP Transport
Session. Templates not refreshed by the Exporting Process within the
lifetime can then be discarded by the Collecting Process. The
template lifetime at the Collecting Process MAY be exposed by a
configuration parameter, or MAY be derived from observation of the
interval of periodic Template retransmissions from the Exporting
Process. In this latter case, the Template lifetime SHOULD default to
at least 3 times the observed retransmission rate.
As template IDs are unique per UDP session and per Observation
Domain, at any given time, the Collecting Process SHOULD maintain the
following for all the current Template Records and Options Template
Records: <IPFIX Device, Exporter source UDP port, Observation Domain
ID, Template ID, Template Definition, Last Received>.
9. The Collecting Process's Side
This section describes the handling of the IPFIX Protocol at the
Collecting Process common to all Transport Protocols. Additional
considerations for SCTP and UDP are given in Sections 9.1 and 9.2
respectively. Template management at Collecting Processes is covered
in Section 8.
The Collecting Process SHOULD listen for association requests /
connections to start new Transport Sessions from the Exporting
Process. [FIXME should? how does it work if this is not a MUST?]
The Collecting Process MUST note the Information Element identifier
of any Information Element that it does not understand and MAY
discard that Information Element from the Flow Record.
The Collecting Process MUST accept padding in Data Records and
Template Records. The padding size is the Set Length minus the size
of the Set Header (4 octets for the Set ID and the Set Length),
modulo the Record size deduced from the Template Record.
The IPFIX protocol has a Sequence Number field in the Export header
that increases with the number of IPFIX Data Records in the IPFIX
Message. A Collector may detect out-of-sequence, dropped, or
duplicate IPFIX Messages by tracking the Sequence Number. A
Collector SHOULD provide a logging mechanism for tracking
out-of-sequence IPFIX Messages. Such out-of-sequence IPFIX Messages
may be due to Exporter resource exhaustion where it cannot transmit
messages at their creation rate, an Exporting Process reset,
<Claise, et al.> Standards Track [Page 40]
Internet-Draft IPFIX Protocol Specification March 9, 2012
congestion on the network link between the Exporter and Collector,
Collector resource exhaustion where it cannot process the IPFIX
Messages at their arrival rate, out-of-order packet reception,
duplicate packet reception, or an attacker injecting false messages.
If the Collecting Process receives a malformed IPFIX Message, it MUST
discard the IPFIX Message and SHOULD log the error. Note that non-
zero Set padding does not constitute a malformed IPFIX Message.
9.1. Additional considerations for SCTP Collecting Processes
The Exporting Process requests a number of streams to use for export
at association setup time. An Exporting Process MAY request and
support more than one stream per SCTP association.
9.2. Additional considerations for UDP Collecting Processes
A Transport Session for IPFIX Messages transported over UDP is
defined from the point of view of the Exporting Process, and roughly
corresponds to the time during which a given Exporting Process sends
IPFIX messages over UDP to a given Collecting Process. Since this is
difficult to detect at the Collecting Process, the Collecting Process
MAY expire all Transport Session state after no IPFIX Messages are
received from a given Exporting Process during a configurable idle
timeout.
The Collecting Process SHOULD accept Data Records without the
associated Template Record (or other definitions) required to decode
the Data Record. If the Template Records (or other definitions such
as Common Properties) have not been received at the time Data Records
are received, the Collecting Process SHOULD store the Data Records
for a short period of time and decode them after the Template Records
(or other definitions) are received. The short period of time MUST
be lower than the lifetime of definitions associated with identifiers
considered unique within the UDP session.
10. Transport Protocol
The IPFIX Protocol Specification has been designed to be transport
protocol independent. Note that the Exporter can export to multiple
Collecting Processes using independent transport protocols.
The IPFIX Message Header 16-bit Length field limits the length of an
IPFIX Message to 65535 octets, including the header. A Collecting
Process MUST be able to handle IPFIX Message lengths of up to 65535
octets.
<Claise, et al.> Standards Track [Page 41]
Internet-Draft IPFIX Protocol Specification March 9, 2012
10.1. Transport Compliance and Transport Usage
SCTP [RFC4960] using the PR-SCTP extension specified in [RFC3758]
MUST be implemented by all compliant implementations. UDP [UDP] MAY
also be implemented by compliant implementations. TCP [TCP] MAY also
be implemented by compliant implementations.
PR-SCTP SHOULD be used in deployments where Exporters and Collectors
are communicating over links that are susceptible to congestion.
PR-SCTP is capable of providing any required degree of reliability.
TCP MAY be used in deployments where Exporters and Collectors
communicate over links that are susceptible to congestion, but
PR-SCTP is preferred due to its ability to limit back pressure on
Exporters and its message versus stream orientation.
UDP MAY be used, although it is not a congestion-aware protocol.
However, in this case the IPFIX traffic between Exporter and
Collector MUST be separately contained or provisioned to minimize the
risk of congestion-related loss.
10.2. SCTP
This section describes how IPFIX is transported over SCTP [RFC4960]
using the PR-SCTP [RFC3758] extension.
10.2.1. Congestion Avoidance
The SCTP transport protocol provides the required level of congestion
avoidance by design.
SCTP will detect congestion in the end-to-end path between the IPFIX
Exporting Process and the IPFIX Collecting Process, and limit the
transfer rate accordingly. When an IPFIX Exporting Process has
records to export, but detects that transmission by SCTP is
temporarily impossible, it can either wait until sending is possible
again, or it can decide to drop the record. In the latter case, the
dropped export data MUST be accounted for, so that the amount of
dropped export data can be reported.
10.2.2. Reliability
The SCTP transport protocol is by default reliable, but has the
capability to deliver messages with partial reliability [RFC3758].
Using reliable SCTP messages for the IPFIX export is not in itself a
guarantee that all Data Records will be delivered. If there is
congestion on the link from the Exporting Process to the Collecting
<Claise, et al.> Standards Track [Page 42]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Process, or if a significant number of retransmissions are required,
the send queues on the Exporting Process may fill up; the Exporting
Process MAY either suspend, export, or discard the IPFIX Messages.
If Data Records are discarded the IPFIX Sequence Numbers used for
export MUST reflect the loss of data.
10.2.3. MTU
SCTP provides the required IPFIX Message fragmentation service based
on path MTU discovery.
10.2.4. Association Establishment and Shutdown
The IPFIX Exporting Process SHOULD initiate an SCTP association with
the IPFIX Collecting Process. By default, the Collecting Process
listens for connections on SCTP port 4739. By default, the
Collecting Process listens for secure connections on SCTP port 4740
(refer to the Security Considerations section). By default, the
Exporting Process tries to connect to one of these ports. It MUST be
possible to configure both the Exporting and Collecting Processes to
use a different SCTP port.
The Exporting Process MAY establish more than one association
(connection "bundle" in SCTP terminology) to the Collecting Process.
An Exporting Process MAY support more than one active association to
different Collecting Processes (including the case of different
Collecting Processes on the same host).
When an Exporting Process is shut down, it SHOULD shut down the SCTP
association.
When a Collecting Process no longer wants to receive IPFIX Messages,
it SHOULD shut down its end of the association. The Collecting
Process SHOULD continue to receive and process IPFIX Messages until
the Exporting Process has closed its end of the association.
When a Collecting Process detects that the SCTP association has been
abnormally terminated, it MUST continue to listen for a new
association establishment.
When an Exporting Process detects that the SCTP association to the
Collecting Process is abnormally terminated, it SHOULD try to
re-establish the association.
Association timeouts SHOULD be configurable.
<Claise, et al.> Standards Track [Page 43]
Internet-Draft IPFIX Protocol Specification March 9, 2012
10.2.5. Failover
If the Collecting Process does not acknowledge the attempt by the
Exporting Process to establish an association, the Exporting Process
should retry using the SCTP exponential backoff feature. The
Exporter MAY log an alarm if the time to establish the association
exceeds a specified threshold, configurable on the Exporter.
If Collecting Process failover is supported by the Exporting Process,
a second SCTP association MAY be opened in advance.
10.2.6. Streams
An Exporting Process MAY request more than one SCTP stream per
association. Each of these streams may be used for the transmission
of IPFIX Messages containing Data Sets, Template Sets, and/or Options
Template Sets.
Depending on the requirements of the application, the Exporting
Process may send Data Sets with full or partial reliability, using
ordered or out-of-order delivery, over any SCTP stream established
during SCTP Association setup.
An IPFIX Exporting Process MAY use any PR-SCTP Service Definition as
per Section 4 of the PR-SCTP [RFC3758] specification when using
partial reliability to transmit IPFIX Messages containing only Data
Sets.
However, Exporting Processes SHOULD mark such IPFIX Messages for
retransmission for as long as resource or other constraints allow.
10.3. UDP
This section describes how IPFIX is transported over UDP [UDP].
10.3.1. Congestion Avoidance
UDP has no integral congestion-avoidance mechanism. Its use over
congestion-sensitive network paths is therefore not recommended. UDP
MAY be used in deployments where Exporters and Collectors always
communicate over dedicated links that are not susceptible to
congestion, i.e., links that are over-provisioned compared to the
maximum export rate from the Exporters.
10.3.2. Reliability
UDP is not a reliable transport protocol, and cannot guarantee
delivery of messages. IPFIX Messages sent from the Exporting Process
<Claise, et al.> Standards Track [Page 44]
Internet-Draft IPFIX Protocol Specification March 9, 2012
to the Collecting Process using UDP may therefore be lost. UDP MUST
NOT be used unless the application can tolerate some loss of IPFIX
Messages.
The Collecting Process SHOULD deduce the loss and reordering of IPFIX
Data Records by looking at the discontinuities in the IPFIX Sequence
Number. In the case of UDP, the IPFIX Sequence Number contains the
total number of IPFIX Data Records sent for the UDP Transport Session
prior to the receipt of this IPFIX Message, modulo 2^32. A Collector
SHOULD detect out-of-sequence, dropped, or duplicate IPFIX Messages
by tracking the Sequence Number. Templates sent from the Exporting
Process to the Collecting Process using UDP as a transport MUST be
re-sent at regular intervals, in case previous copies were lost.
Exporting Processes exporting IPFIX Messages via UDP MUST include a
valid UDP checksum.
10.3.3. MTU
The maximum size of exported messages MUST be configured such that
the total packet size does not exceed the path MTU. If the path MTU
is unknown, a maximum packet size of 512 octets SHOULD be used.
10.3.4. Session Establishment and Shutdown
By default, the Collecting Process listens on the UDP port 4739. By
default, the Collecting Process listens for secure connections on UDP
port 4740 (refer to the "Security Considerations" section). By
default, the Exporting Process tries to connect to one of these
ports. It MUST be possible to configure both the Exporting and
Collecting Processes to use a different UDP port.
As UDP is a connectionless protocol, there is no real session
establishment or shutdown for IPFIX over UDP. An Exporting Process
starts sending IPFIX Messages to a Collecting Process at one point in
time, and stops sending them at another point in time. This leads to
some complications in template management, which are outlined in
Section 8.4 above.
10.3.5. Failover and Session Duplication
Because UDP is not a connection-oriented protocol, the Exporting
Process is unable to determine from the transport protocol that the
Collecting Process is no longer able to receive the IPFIX Messages.
Therefore, it cannot invoke a failover mechanism. However, the
Exporting Process MAY duplicate the IPFIX Message to several
Collecting Processes.
<Claise, et al.> Standards Track [Page 45]
Internet-Draft IPFIX Protocol Specification March 9, 2012
10.4. TCP
The IPFIX Exporting Process initiates a TCP connection to the
Collecting Process. By default, the Collecting Process listens for
connections on TCP port 4739. By default, the Collecting Process
listens for secure connections on TCP port 4740 (refer to the
Security Considerations section). By default, the Exporting Process
tries to connect to one of these ports. It MUST be possible to
configure both the Exporting Process and the Collecting Process to
use a different TCP port.
An Exporting Process MAY support more than one active connection to
different Collecting Processes (including the case of different
Collecting Processes on the same host).
The Exporter MAY log an alarm if the time to establish the connection
exceeds a specified threshold, configurable on the Exporter.
10.4.1. Congestion Avoidance
TCP controls the rate at which data can be sent from the Exporting
Process to the Collecting Process, using a mechanism that takes into
account both congestion in the network and the capabilities of the
receiver.
Therefore, an IPFIX Exporting Process may not be able to send IPFIX
Messages at the rate that the Metering Process generates it, either
because of congestion in the network or because the Collecting
Process cannot handle IPFIX Messages fast enough. As long as
congestion is transient, the Exporting Process can buffer IPFIX
Messages for transmission. But such buffering is necessarily limited,
both because of resource limitations and because of timeliness
requirements, so ongoing and/or severe congestion may lead to a
situation where the Exporting Process is blocked.
When an Exporting Process has Data Records to export but the
transmission buffer is full, and it wants to avoid blocking, it can
decide to drop some Data Records. The dropped Data Records MUST be
accounted for, so that the number of lost records can later be
exported as in Section 4.3.
When an Exporting Process finds that the rate at which records should
be exported is consistently higher than the rate at which TCP sending
permits, it SHOULD provide back pressure to the Metering Processes.
The Metering Process could then adapt by temporarily reducing the
amount of data it generates, for example, using sampling or
aggregation.
<Claise, et al.> Standards Track [Page 46]
Internet-Draft IPFIX Protocol Specification March 9, 2012
10.4.2. Reliability
TCP ensures reliable delivery of data from the Exporting Process to
the Collecting Process.
In the case of TCP, the IPFIX Sequence Number contains the total
number of IPFIX Data Records sent from this TCP connection, from the
current Observation Domain by the Exporting Process, prior to the
receipt of this IPFIX Message, modulo 2^32.
10.4.3. MTU
As TCP offers a stream service instead of a datagram or sequential
packet service, IPFIX Messages transported over TCP are instead
separated using the Length field in the IPFIX Message Header. The
Exporting Process can choose any valid length for exported IPFIX
Messages, as TCP handles segmentation.
However, if an Exporting Process exports data from multiple
Observation Domains, it should be careful to choose IPFIX Message
lengths appropriately to minimize head-of-line blocking between
different Observation Domains. Multiple TCP connections MAY be used
to avoid head-of-line blocking between different Observation Domains.
10.4.4. Connection Establishment, Shutdown, and Restart
The IPFIX Exporting Process initiates a TCP connection to the
Collecting Process. By default, the Collecting Process listens for
connections on TCP port 4739. By default, the Collecting Process
listens for secure connections on TCP port 4740 (refer to the
Security Considerations section). By default, the Exporting Process
tries to connect to one of these ports. It MUST be possible to
configure both the Exporting Process and the Collecting Process to
use a different TCP port.
An Exporting Process MAY support more than one active connection to
different Collecting Processes (including the case of different
Collecting Processes on the same host).
The Exporter MAY log an alarm if the time to establish the connection
exceeds a specified threshold, configurable on the Exporter.
When an Exporting Process is shut down, it SHOULD shut down the TCP
connection.
When a Collecting Process no longer wants to receive IPFIX Messages,
it SHOULD close its end of the connection. The Collecting Process
SHOULD continue to read IPFIX Messages until the Exporting Process
<Claise, et al.> Standards Track [Page 47]
Internet-Draft IPFIX Protocol Specification March 9, 2012
has closed its end.
When a Collecting Process detects that the TCP connection to the
Exporting Process has terminated abnormally, it MUST continue to
listen for a new connection.
When an Exporting Process detects that the TCP connection to the
Collecting Process has terminated abnormally, it SHOULD try to
re-establish the connection. Connection timeouts and retry schedules
SHOULD be configurable. In the default configuration, an Exporting
Process MUST NOT attempt to establish a connection more frequently
than once per minute.
10.4.5. Failover
If the Collecting Process does not acknowledge the attempt by the
Exporting Process to establish a connection, it will retry using the
TCP exponential backoff feature.
If Collecting Process failover is supported by the Exporting Process,
a second TCP connection MAY be opened in advance.
11. Security Considerations
The security considerations for the IPFIX protocol have been derived
from an analysis of potential security threats, as discussed in the
"Security Considerations" section of IPFIX requirements [RFC3917].
The requirements for IPFIX security are as follows:
1. IPFIX must provide a mechanism to ensure the confidentiality of
IPFIX data transferred from an Exporting Process to a Collecting
Process, in order to prevent disclosure of Flow Records
transported via IPFIX.
2. IPFIX must provide a mechanism to ensure the integrity of IPFIX
data transferred from an Exporting Process to a Collecting
Process, in order to prevent the injection of incorrect data or
control information (e.g., Templates) into an IPFIX Message
stream.
3. IPFIX must provide a mechanism to authenticate IPFIX Collecting
and Exporting Processes, to prevent the collection of data from an
unauthorized Exporting Process or the export of data to an
unauthorized Collecting Process.
Because IPFIX can be used to collect information for network
forensics and billing purposes, attacks designed to confuse, disable,
or take information from an IPFIX collection system may be seen as a
<Claise, et al.> Standards Track [Page 48]
Internet-Draft IPFIX Protocol Specification March 9, 2012
prime objective during a sophisticated network attack.
An attacker in a position to inject false messages into an IPFIX
Message stream can either affect the application using IPFIX (by
falsifying data), or the IPFIX Collecting Process itself (by
modifying or revoking Templates, or changing options); for this
reason, IPFIX Message integrity is important.
The IPFIX Messages themselves may also contain information of value
to an attacker, including information about the configuration of the
network as well as end-user traffic and payload data, so care must be
taken to confine their visibility to authorized users. When an
Information Element containing end-user payload information is
exported, it SHOULD be transmitted to the Collecting Process using a
means that secures its contents against eavesdropping. Suitable
mechanisms include the use of either a direct point-to-point
connection or the use of an encryption mechanism. It is the
responsibility of the Collecting Process to provide a satisfactory
degree of security for this collected data, including, if necessary,
anonymization of any reported data.
11.1. Applicability of TLS and DTLS
Transport Layer Security (TLS) [RFC5246] and Datagram Transport Layer
Security (DTLS) [RFC4347] were designed to provide the
confidentiality, integrity, and authentication assurances required by
the IPFIX protocol, without the need for pre-shared keys.
With the mandatory SCTP and PR-SCTP transport protocols for IPFIX,
DTLS [RFC4347] MUST be implemented. If UDP is selected as the IPFIX
transport protocol, DTLS [RFC4347] MUST be implemented. If TCP is
selected as the IPFIX transport protocol, TLS [RFC5246] MUST be
implemented.
Note that DTLS is selected as the security mechanism for SCTP and PR-
SCTP. Though TLS bindings to SCTP are defined in [RFC3436], they
require all communication to be over reliable, bidirectional streams,
and require one TLS connection per stream. This arrangement is not
compatible with the rationale behind the choice of SCTP as an IPFIX
transport protocol.
Note that using DTLS [RFC4347] has a vulnerability, i.e., a true man
in the middle may attempt to take data out of an association and fool
the sender into thinking that the data was actually received by the
peer. In generic TLS for SCTP (and/or TCP), this is not possible.
This means that the removal of a message may become hidden from the
sender or receiver. Another vulnerability of using PR-SCTP with DTLS
is that someone could inject SCTP control information to shut down
<Claise, et al.> Standards Track [Page 49]
Internet-Draft IPFIX Protocol Specification March 9, 2012
the SCTP association, effectively generating a loss of IPFIX Messages
if those are buffered outside of the SCTP association. Techniques
such as [RFC6083] could be used to overcome these vulnerabilities.
When using DTLS over SCTP, the Exporting Process MUST ensure that
each IPFIX Message is sent over the same SCTP stream that would be
used when sending the same IPFIX Message directly over SCTP. Note
that DTLS may send its own control messages on stream 0 with full
reliability; however, this will not interfere with the processing of
stream 0 IPFIX Messages at the Collecting Process, because DTLS
consumes its own control messages before passing IPFIX Messages up to
the application layer.
When using DTLS over SCTP or UDP, the Heartbeat Extention [RFC6520]
SHOULD be used, especially on long-lived Transport Sessions, to
ensure that the association remains active.
11.2. Usage
The IPFIX Exporting Process initiates the communication to the IPFIX
Collecting Process, and acts as a TLS or DTLS client according to
[RFC5246] and [RFC4347], while the IPFIX Collecting Process acts as a
TLS or DTLS server. The DTLS client opens a secure connection on the
SCTP port 4740 of the DTLS server if SCTP or PR-SCTP is selected as
the transport protocol. The TLS client opens a secure connection on
the TCP port 4740 of the TLS server if TCP is selected as the
transport protocol. The DTLS client opens a secure connection on the
UDP port 4740 of the DTLS server if UDP is selected as the transport
protocol.
11.3. Authentication
IPFIX Exporting Processes and IPFIX Collecting Processes are
identified by the fully qualified domain name of the interface on
which IPFIX Messages are sent or received, for purposes of X.509
client and server certificates as in [RFC5280].
To prevent man-in-the-middle attacks from impostor Exporting or
Collecting Processes, the acceptance of data from an unauthorized
Exporting Process, or the export of data to an unauthorized
Collecting Process, strong mutual authentication via asymmetric keys
MUST be used for both TLS and DTLS. Each of the IPFIX Exporting and
Collecting Processes MUST verify the identity of its peer against its
authorized certificates, and MUST verify that the peer's certificate
matches its fully qualified domain name, or, in the case of SCTP, the
fully qualified domain name of one of its endpoints.
<Claise, et al.> Standards Track [Page 50]
Internet-Draft IPFIX Protocol Specification March 9, 2012
The fully qualified domain name used to identify an IPFIX Collecting
Process or Exporting Process may be stored either in a subjectAltName
extension of type dNSName, or in the most specific Common Name field
of the Subject field of the X.509 certificate. If both are present,
the subjectAltName extension is given preference.
Internationalized domain names (IDN) in either the subjectAltName
extension of type dNSName or the most specific Common Name field of
the Subject field of the X.509 certificate MUST be encoded using
Punycode [RFC3492] as described in [RFC5891], "Conversion
Operations".
11.4. Protection against DoS Attacks
An attacker may mount a denial-of-service (DoS) attack against an
IPFIX collection system either directly, by sending large amounts of
traffic to a Collecting Process, or indirectly, by generating large
amounts of traffic to be measured by a Metering Process.
Direct denial-of-service attacks can also involve state exhaustion,
whether at the transport layer (e.g., by creating a large number of
pending connections), or within the IPFIX Collecting Process itself
(e.g., by sending Flow Records pending Template or scope information,
a large amount of Options Template Records, etc.).
SCTP mandates a cookie-exchange mechanism designed to defend against
SCTP state exhaustion denial-of-service attacks. Similarly, TCP
provides the "SYN cookie" mechanism to mitigate state exhaustion; SYN
cookies SHOULD be used by any Collecting Process accepting TCP
connections. DTLS also provides cookie exchange to protect against
DTLS server state exhaustion.
The reader should note that there is no way to prevent fake IPFIX
Message processing (and state creation) for UDP & SCTP communication.
The use of TLS and DTLS can obviously prevent the creation of fake
states, but they are themselves prone to state exhaustion attacks.
Therefore, Collector rate limiting SHOULD be used to protect TLS &
DTLS (like limiting the number of new TLS or DTLS session per second
to a sensible number).
IPFIX state exhaustion attacks can be mitigated by limiting the rate
at which new connections or associations will be opened by the
Collecting Process, the rate at which IPFIX Messages will be accepted
by the Collecting Process, and adaptively limiting the amount of
state kept, particularly records waiting on Templates. These rate
and state limits MAY be provided by a Collecting Process; if
provided, the limits SHOULD be user configurable.
<Claise, et al.> Standards Track [Page 51]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Additionally, an IPFIX Collecting Process can eliminate the risk of
state exhaustion attacks from untrusted nodes by requiring TLS or
DTLS mutual authentication, causing the Collecting Process to accept
IPFIX Messages only from trusted sources.
With respect to indirect denial of service, the behavior of IPFIX
under overload conditions depends on the transport protocol in use.
For IPFIX over TCP, TCP congestion control would cause the flow of
IPFIX Messages to back off and eventually stall, blinding the IPFIX
system. PR-SCTP improves upon this situation somewhat, as some IPFIX
Messages would continue to be received by the Collecting Process due
to the avoidance of head-of-line blocking by SCTP's multiple streams
and partial reliability features, possibly affording some visibility
of the attack. The situation is similar with UDP, as some datagrams
may continue to be received at the Collecting Process, effectively
applying sampling to the IPFIX Message stream, implying that some
forensics may be left.
To minimize IPFIX Message loss under overload conditions, some
mechanism for service differentiation could be used to prioritize
IPFIX traffic over other traffic on the same link. Alternatively,
IPFIX Messages can be transported over a dedicated network. In this
case, care must be taken to ensure that the dedicated network can
handle the expected peak IPFIX Message traffic.
11.5. When DTLS or TLS Is Not an Option
The use of DTLS or TLS might not be possible in some cases due to
performance issues or other operational concerns.
Without TLS or DTLS mutual authentication, IPFIX Exporting Processes
and Collecting Processes can fall back on using IP source addresses
to authenticate their peers. A policy of allocating Exporting
Process and Collecting Process IP addresses from specified address
ranges, and using ingress filtering to prevent spoofing, can improve
the usefulness of this approach. Again, completely segregating IPFIX
traffic on a dedicated network, where possible, can improve security
even further. In any case, the use of open Collecting Processes
(those that will accept IPFIX Messages from any Exporting Process
regardless of IP address or identity) is discouraged.
Modern TCP and SCTP implementations are resistant to blind insertion
attacks (see [RFC1948], [RFC4960]); however, UDP offers no such
protection. For this reason, IPFIX Message traffic transported via
UDP and not secured via DTLS SHOULD be protected via segregation to a
dedicated network.
<Claise, et al.> Standards Track [Page 52]
Internet-Draft IPFIX Protocol Specification March 9, 2012
11.6. Logging an IPFIX Attack
IPFIX Collecting Processes MUST detect potential IPFIX Message
insertion or loss conditions by tracking the IPFIX Sequence Number,
and SHOULD provide a logging mechanism for reporting out-of-sequence
messages. Note that an attacker may be able to exploit the handling
of out-of-sequence messages at the Collecting Process, so care should
be taken in handling these conditions. For example, a Collecting
Process that simply resets the expected Sequence Number upon receipt
of a later Sequence Number could be temporarily blinded by deliberate
injection of later Sequence Numbers.
IPFIX Exporting and Collecting Processes SHOULD log any connection
attempt that fails due to authentication failure, whether due to
being presented an unauthorized or mismatched certificate during TLS
or DTLS mutual authentication, or due to a connection attempt from an
unauthorized IP address when TLS or DTLS is not in use.
IPFIX Exporting and Collecting Processes SHOULD detect and log any
SCTP association reset or TCP connection reset.
11.7. Securing the Collector
The security of the Collector and its implementation is important to
achieve overall security. However, it is outside the scope of this
document.
12. IANA Considerations
IPFIX Messages use two fields with assigned values. These are the
IPFIX Version Number, indicating which version of the IPFIX Protocol
was used to export an IPFIX Message, and the IPFIX Set ID, indicating
the type for each set of information within an IPFIX Message.
The IPFIX Version Number value of 10 is reserved for the IPFIX
protocol specified in this document. Set ID values of 0 and 1 are
not used for historical reasons [RFC3954]. The Set ID value of 2 is
reserved for the Template Set. The Set ID value of 3 is reserved for
the Options Template Set. All other Set ID values from 4 to 255 are
reserved for future use. Set ID values above 255 are used for Data
Sets.
New assignments in either IPFIX Version Number or IPFIX Set ID
assignments require a Standards Action [RFC5226], i.e., they are to
be made via Standards Track RFCs approved by the IESG.
<Claise, et al.> Standards Track [Page 53]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Appendix A. IPFIX Encoding Examples
This appendix, which is a not a normative reference, contains IPFIX
encoding examples.
Let's consider the example of an IPFIX Message composed of a
Template Set, a Data Set (which contains three Data Records), an
Options Template Set and a Data Set (which contains 2 Data Records
related to the previous Options Template Record).
IPFIX Message:
+--------+------------------------------------------. . .
| | +--------------+ +------------------+
|Message | | Template | | Data |
| Header | | Set | | Set | . . .
| | | (1 Template) | | (3 Data Records) |
| | +--------------+ +------------------+
+--------+------------------------------------------. . .
. . .-------------------------------------------+
+------------------+ +------------------+ |
| Options | | Data | |
. . . | Template Set | | Set | |
| (1 Template) | | (2 Data Records) | |
+------------------+ +------------------+ |
. . .-------------------------------------------+
A.1. Message Header Example
The Message Header is composed of:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Version = 0x000a | Length = 152 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Export Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Observation Domain ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
<Claise, et al.> Standards Track [Page 54]
Internet-Draft IPFIX Protocol Specification March 9, 2012
A.2. Template Set Examples
A.2.1. Template Set Using IETF-Specified Information Elements
We want to report the following Information Elements:
- The IPv4 source IP address: sourceIPv4Address in [RFC5102bis],
with a length of 4 octets
- The IPv4 destination IP address: destinationIPv4Address in
[RFC5102bis], with a length of 4 octets
- The next-hop IP address (IPv4): ipNextHopIPv4Address in
[RFC5102bis], with a length of 4 octets
- The number of packets of the Flow: packetDeltaCount in
[RFC5102bis], with a length of 4 octets
- The number of octets of the Flow: octetDeltaCount in
[RFC5102bis], with a length of 4 octets
Therefore, the Template Set will be composed of the following:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length = 28 octets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 256 | Field Count = 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| sourceIPv4Address = 8 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| destinationIPv4Address = 12 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| ipNextHopIPv4Address = 15 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| packetDeltaCount = 2 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| octetDeltaCount = 1 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
A.2.2. Template Set Using Enterprise-Specific Information Elements
We want to report the following Information Elements:
- The IPv4 source IP address: sourceIPv4Address in [RFC5102bis], with
a length of 4 octets
<Claise, et al.> Standards Track [Page 55]
Internet-Draft IPFIX Protocol Specification March 9, 2012
- The IPv4 destination IP address: destinationIPv4Address in
[RFC5102bis], with a length of 4 octets
- An enterprise-specific Information Element representing
proprietary information, with a type of 15 and a length of 4
- The number of packets of the Flow: packetDeltaCount in
[RFC5102bis], with a length of 4 octets
- The number of octets of the Flow: octetDeltaCount in [RFC5102bis],
with a length of 4 octets
Therefore, the Template Set will be composed of the following:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 2 | Length = 32 octets |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 257 | Field Count = 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| sourceIPv4Address = 8 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| destinationIPv4Address = 12 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1| Information Element Id. = 15| Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Enterprise number |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| packetDeltaCount = 2 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0| octetDeltaCount = 1 | Field Length = 4 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
<Claise, et al.> Standards Track [Page 56]
Internet-Draft IPFIX Protocol Specification March 9, 2012
A.3. Data Set Example
In this example, we report the following three Flow Records:
Src IP addr. | Dst IP addr. | Next Hop addr. | Packet | Octets
| | | Number | Number
------------------------------------------------------------------
192.0.2.12 | 192.0.2.254 | 192.0.2.1 | 5009 | 5344385
192.0.2.27 | 192.0.2.23 | 192.0.2.2 | 748 | 388934
192.0.2.56 | 192.0.2.65 | 192.0.2.3 | 5 | 6534
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 256 | Length = 64 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.12 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.254 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5009 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5344385 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.27 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.23 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 748 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 388934 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.56 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.65 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 192.0.2.3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 6534 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Note that padding is not necessary in this example.
<Claise, et al.> Standards Track [Page 57]
Internet-Draft IPFIX Protocol Specification March 9, 2012
A.4. Options Template Set Examples
A.4.1. Options Template Set Using IETF-Specified Information Elements
Per line card (the router being composed of two line cards), we want
to report the following Information Elements:
- Total number of IPFIX Messages: exportedMessageTotalCount
[RFC5102bis], with a length of 2 octets
- Total number of exported Flows: exportedFlowRecordTotalCount
[RFC5102bis], with a length of 2 octets
The line card, which is represented by the lineCardId Information
Element [RFC5102bis], is used as the Scope Field.
Therefore, the Options Template Set will be:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 24 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 258 | Field Count = 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = 1 |0| lineCardId = 141 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length = 4 |0|exportedMessageTotalCount=41 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |0|exportedFlowRecordTotalCo.=42|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
A.4.2. Options Template Set Using Enterprise-Specific Information
Elements
Per line card (the router being composed of two line cards), we want
to report the following Information Elements:
- Total number of IPFIX Messages: exportedMessageTotalCount
[RFC5102bis], with a length of 2 octets
- An enterprise-specific number of exported Flows, with a type of
42 and a length of 4 octets
The line card, which is represented by the lineCardId Information
<Claise, et al.> Standards Track [Page 58]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Element [RFC5102bis], is used as the Scope Field.
The format of the Options Template Set is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 259 | Field Count = 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = 1 |0| lineCardId = 141 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length = 4 |0|exportedFlowRecordTotalCo.=41|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |1|Information Element Id. = 42 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 4 | Enterprise number ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Enterprise number | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
A.4.3. Options Template Set Using an Enterprise-Specific Scope
In this example, we want to export the same information as in the
example in Section A.4.1:
- Total number of IPFIX Messages: exportedMessageTotalCount
[RFC5102bis], with a length of 2 octets
- Total number of exported Flows: exportedFlowRecordTotalCount
[RFC5102bis], with a length of 2 octets
But this time, the information pertains to a proprietary scope,
identified by enterprise-specific Information Element number 123.
<Claise, et al.> Standards Track [Page 59]
Internet-Draft IPFIX Protocol Specification March 9, 2012
The format of the Options Template Set is now as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 3 | Length = 28 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Template ID 260 | Field Count = 3 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope Field Count = 1 |1|Scope 1 Infor. El. Id. = 123 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Scope 1 Field Length = 4 | Enterprise Number ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
... Enterprise Number |0|exportedMessageTotalCount=41 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 |0|exportedFlowRecordTotalCo.=42|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Field Length = 2 | Padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
A.4.4. Data Set Using an Enterprise-Specific Scope
In this example, we report the following two Data Records:
Enterprise field 123 | IPFIX Message | Exported Flow Records
-------------------------------------------------------------------
1 | 345 | 10201
2 | 690 | 20402
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Set ID = 260 | Length = 20 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 345 | 10201 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 690 | 20402 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
<Claise, et al.> Standards Track [Page 60]
Internet-Draft IPFIX Protocol Specification March 9, 2012
A.5. Variable-Length Information Element Examples
A.5.1. Example of Variable-Length Information Element with Length
Inferior to 255 Octets
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5 | 5 octet Information Element |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
A.5.2. Example of Variable-Length Information Element with 3 Octet
Length Encoding
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 255 | 1000 | IE ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 1000 octet Information Element |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
: ... :
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... IE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
References
Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3436] Jungmaier, A., Rescorla, E., and M. Tuexen, "Transport
Layer Security over Stream Control Transmission
Protocol", RFC 3436, December 2002.
[RFC3492] Costello, A., "Punycode: A Bootstring encoding of
Unicode for Internationalized Domain Names in
Applications (IDNA)", RFC 3492, March 2003.
[RFC3758] Stewart, R., Ramalho, M., Xie, Q., Tuexen, M., and P.
Conrad, "Stream Control Transmission Protocol (SCTP)
Partial Reliability Extension", RFC 3758, May 2004.
<Claise, et al.> Standards Track [Page 61]
Internet-Draft IPFIX Protocol Specification March 9, 2012
[RFC4347] Rescorla, E. and N. Modadugu, "Datagram Transport
Layer Security", RFC 4347, April 2006.
[RFC4960] Stewart, R., Ed., "Stream Control Transmission
Protocol", RFC 4960, September 2007.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing
an IANA Considerations Section in RFCs", BCP 26, RFC
5226, May 2008.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer
Security (TLS) Protocol Version 1.2", RFC 5246,
August 2008.
[RFC5280] Cooper, D., Santesson, S., Farrell, S. Boeyen, S.
Housley, R., and W. Polk, "Internet X.509 Public Key
Infrastructure Certificate and Certificate Revocation
List (CRL) Profile", RFC 5280, April 2008.
[RFC5905] Mills, D., Delaware, U., Martin, J., Burbank, J. and
W. Kasch, "Network Time Protocol Version 4: Protocol
and Algorithms Specification", RFC 5905, June 2010
[RFC5891] J. Klensin, "Internationalized Domain Names in
Applications (IDNA): Protocol", RFC 5891, August
2010.
[RFC6520] Seggelmann, R., Tuexen, M., and Williams, M.,
"Transport Layer Security (TLS) and Datagram
Transport Layer Security (DTLS) Heartbeat Extension",
RFC 6520, February 2012.
[TCP] Postel, J., "Transmission Control Protocol", STD 7,
RFC 793, September 1981.
[UDP] Postel, J., "User Datagram Protocol", STD 6, RFC 768,
August 1980.
[RFC5102bis] Quittek, J., Bryant S., Claise, B., Aitken, P., and J.
Meyer, "Information Model for IP Flow Information
Export", draft-claise-ipfix-information-model-
rfc5102bis-01.txt, Work in Progress, October 2011.
Informative References
[PEN] IANA Private Enterprise Numbers registry
http://www.iana.org/assignments/enterprise-numbers.
<Claise, et al.> Standards Track [Page 62]
Internet-Draft IPFIX Protocol Specification March 9, 2012
[RFC1948] Bellovin, S., "Defending Against Sequence Number
Attacks", RFC 1948, May 1996.
[RFC2579] McCloghrie, K., Perkins, D., and J. Schoenwaelder,
"Textual Conventions for SMIv2", STD 58, RFC 2579,
April 1999.
[RFC3550] Schulzrinne, H., Casner, S., Frederick, R., and V.
Jacobson, "RTP: A Transport Protocol for Real-Time
Applications", STD 64, RFC 3550, July 2003.
[RFC3917] Quittek, J., Zseby, T., Claise, B., and S. Zander,
"Requirements for IP Flow Information Export
(IPFIX)", RFC 3917, October 2004.
[RFC3954] Claise, B., Ed., "Cisco Systems NetFlow Services
Export Version 9", RFC 3954, October 2004.
[RFC5101] Claise, B., Ed., "Bidirectional Flow Export Using IP
Flow Information Export (IPFIX)", RFC 5103, January
2008.
[RFC5103] Trammell, B., and E. Boschi, "Specification of the IP
Flow Information Export (IPFIX) Protocol for the
Exchange of IP Traffic Flow Information", RFC 5101,
January 2008.
[RFC5153] Boschi, E., Mark, L., Quittek J., and P. Aitken, "IP
Flow Information Export (IPFIX) Implementation
Guidelines", RFC5153, April 2008
[RFC5470] Sadasivan, G., Brownlee, N., Claise, B., and J.
Quittek, "Architecture for IP Flow Information
Export", RFC5470, March 2009.
[RFC5472] Zseby, T., Boschi, E., Brownlee, N., and B. Claise,
"IP Flow Information Export (IPFIX) Applicability",
RFC5472, March 2009.
[RFC5471] Schmoll, C., Aitken, P., and B. Claise, "Guidelines
for IP Flow Information Export (IPFIX) Testing",
RFC5471, March 2009
[RFC5473] Boschi, E., Mark, L., and B. Claise, "Reducing
Redundancy in IP Flow Information Export (IPFIX) and
Packet Sampling (PSAMP) Reports", RFC5473, March 2009
[RFC5610] Boschi, E., Trammell, B., Mark, L., and T. Zseby,
<Claise, et al.> Standards Track [Page 63]
Internet-Draft IPFIX Protocol Specification March 9, 2012
"Exporting Type Information for IP Flow Information
Export (IPFIX) Information Elements", July 2009.
[RFC6083] Tuexen, M., Seggelman, R. and E. Rescola, "Datagram
Transport Layer Security (DTLS) for Stream Control
Transmission Protocol (SCTP)", RFC6083, January 2011.
[RFC6313] Claise, B., Dhandapani, G., Aitken, P, and S. Yates,
"Export of Structured Data in IP Flow Information
Export (IPFIX)", RFC6313, July 2011.
[RFC6183] Kobayashi, A., Claise, B., Muenz, G, and K. Ishibashi,
"IP Flow Information Export (IPFIX) Mediation:
Framework", RFC6183, April 2011.
[POSIX.1] IEEE 1003.1-2008 - IEEE Standard for Information
Technology - Portable Operating System Interface,
IEEE, 2008.
[IEEE.754.1985] Institute of Electrical and Electronics Engineers,
"Standard for Binary Floating-Point Arithmetic", IEEE
Standard 754, August 1985.
[IPFIX-CONF] Muenz, G., Claise, B., and P. Aitken, "Configuration
Data Model for IPFIX and PSAMP", draft-ietf-ipfix-
configuration-model-10, Work in Progress, July 2011.
[IPFIX-PER-SCTP-STREAM] Claise, B., Aitekn, P., Johnson, A. and G.
Muenz, "IPFIX Export per SCTP Stream", draft-ietf-
ipfix-export-per-sctp-stream-08, Work in Progress,
May 2010.
[IPFIX-MED-PROTO] Claise, B., Kobayashi, A., and B. Trammell,
"Specification of the Protocol for IPFIX Mediations",
draft-claise-ipfix-mediation-protocol-04, Work in
Progress, July 2011.
[RFC5815bis] Dietz, T., Kobayashi, A., Claise, B., and G. Muenz,
"Definitions of Managed Objects for IP Flow
Information Export", draft-dkcm-ipfix-rfc5815bis-
00.txt, Work in Progress, October 2011.
Acknowledgments
We would like to thank the following persons: Ganesh Sadasivan for
his significant contribution during the initial phases of the
protocol specification; Juergen Quittek for the coordination job
within IPFIX and PSAMP; Nevil Brownlee, Dave Plonka, Paul Aitken, and
<Claise, et al.> Standards Track [Page 64]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Andrew Johnson for the thorough reviews; Randall Stewart and Peter
Lei for their SCTP expertise and contributions; Martin Djernaes for
the first essay on the SCTP section; Michael Behringer and Eric
Vyncke for their advice and knowledge in security; Michael Tuexen for
his help regarding the DTLS section; Elisa Boschi for her
contribution regarding the improvement of SCTP sections; Mark
Fullmer, Sebastian Zander, Jeff Meyer, Maurizio Molina, Carter
Bullard, Tal Givoly, Lutz Mark, David Moore, Robert Lowe, Paul
Calato, and many more, for the technical reviews and feedback.
Authors' Addresses
Benoit Claise (Ed.)
Cisco Systems
De Kleetlaan 6a b1
1831 Diegem
Belgium
Phone: +32 2 704 5622
EMail: bclaise@cisco.com
Brian Trammell (Ed.)
Swiss Federal Institute of Technology Zurich
Gloriastrasse 35
8092 Zurich
Switzerland
Phone: +41 44 632 70 13
EMail: trammell@tik.ee.ethz.ch
Stewart Bryant
Cisco Systems, Inc.
250, Longwater,
Green Park,
Reading, RG2 6GB,
United Kingdom
Phone: +44 (0)20 8824-8828
EMail: stbryant@cisco.com
<Claise, et al.> Standards Track [Page 65]
Internet-Draft IPFIX Protocol Specification March 9, 2012
Simon Leinen
SWITCH
Werdstrasse 2
P.O. Box
8021 Zurich
Switzerland
Phone: +41 44 268 1536
EMail: simon.leinen@switch.ch
Thomas Dietz
NEC Europe Ltd.
NEC Laboratories Europe
Network Research Division
Kurfuersten-Anlage 36
69115 Heidelberg
Germany
Phone: +49 6221 4342-128
EMail: Thomas.Dietz@nw.neclab.eu
<Claise, et al.> Standards Track [Page 66]