Network Working Group J. Uttaro
Internet-Draft AT&T
Updates: 5575 (if approved) J. Alcaide
Intended status: Standards Track C. Filsfils
Expires: May 9, 2019 D. Smith
Cisco
P. Mohapatra
Sproute Networks
November 5, 2018
Revised Validation Procedure for BGP Flow Specifications
draft-ietf-idr-bgp-flowspec-oid-07
Abstract
This document describes a modification to the validation procedure
defined in RFC 5575 for the dissemination of BGP flow specifications.
RFC 5575 requires that the originator of the flow specification
matches the originator of the best-match unicast route for the
destination prefix embedded in the flow specification. This allows
only BGP speakers within the data forwarding path (such as autonomous
system border routers) to originate BGP flow specifications. Though
it is possible to disseminate such flow specifications directly from
border routers, it may be operationally cumbersome in an autonomous
system with a large number of border routers having complex BGP
policies. The modification proposed herein enables flow
specifications to be originated from a centralized BGP route
controller.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 9, 2019.
Uttaro, et al. Expires May 9, 2019 [Page 1]
Internet-Draft Revised Flowspec Validation Procedure November 2018
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Requirements Language . . . . . . . . . . . . . . . . . . . . 2
2. Motivation . . . . . . . . . . . . . . . . . . . . . . . . . 2
3. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
4. Revised Validation Procedure . . . . . . . . . . . . . . . . 5
5. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 7
6. Security Considerations . . . . . . . . . . . . . . . . . . . 7
7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 7
8. Normative References . . . . . . . . . . . . . . . . . . . . 7
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 8
1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2. Motivation
Step (a) of the validation procedure in [RFC5575], section 6 is
defined with the underlying assumption that the flow specification
NLRI traverses the same path, in the inter-domain and intra-domain
route distribution graph, as that of the longest-match unicast route
for the destination prefix embedded in the flow specification.
In the case of inter-domain traffic filtering, for example, the flow
specification originator at the egress border routers of ASN1 (RTR-D
and RTR-E in figure 1) matches the EBGP neighbor that advertised the
longest match destination prefix (RTR-F and RTR-G respectively).
Similarly, at the ingress border routers of ASN1 (RTR-A and RTR-B in
figure 1), the flow specification originator matches the egress IBGP
border routers that had advertised the unicast route for the best-
Uttaro, et al. Expires May 9, 2019 [Page 2]
Internet-Draft Revised Flowspec Validation Procedure November 2018
match destination prefix (RTR-D and RTR-E respectively). This is
true even when ingress border routers select paths from different
egress border routers as best path based upon IGP distance (as an
example, RTR-A chooses RTR-D's path as best; RTR-B chooses RTR-E as
the best path).
/ - - - - - - - - - - - - - -
| ASN1 |
+-------+ +-------+
| | | | | |
| RTR-A | | RTR-B |
| | | | | |
+-------+ +-------+
| \ / |
IBGP \ / IBGP
| \ / |
+-------+
| | | |
| RTR-C |
| | RC | |
+-------+
| / \ |
/ \
| IBGP / \ IBGP |
+-------+ +-------+
| | RTR-D | | RTR-E | |
| | | |
| | | | | |
+-------+ +-------+
| | | |
- - -|- - - - - - - - -|- - -/
| EBGP EBGP |
- - -|- - - - - - - - -|- - -/
| | | |
+-------+ +-------+
| | | | | |
| RTR-F | | RTR-G |
| | | | | |
+-------+ +-------+
| ASN2 |
/ - - - - - - - - - - - - - -
Figure 1
It is highly desirable that each ASN is able to protect itself
independently from network security attacks using the BGP flow
specification NLRI for intra-domain purposes only. Network operators
often deploy a dedicated Security Operations Center (SOC) within
Uttaro, et al. Expires May 9, 2019 [Page 3]
Internet-Draft Revised Flowspec Validation Procedure November 2018
their ASN to monitor and detect such security attacks. To mitigate
attacks in a scalable intra-domain manner, operators require the
ability to originate intra-domain flow specification NLRIs from a
central BGP route controller that is not within the data forwarding
plane. In this way, operators can direct border routers within their
ASN with specific attack mitigation actions (drop the traffic,
forward to a clean-pipe center, etc.). To originate a flow
specification NLRI, a central BGP route controller must set itself as
the originator in the flowspec NLRI. This is necessary given the
route controller is originating the flow specification not reflecting
it, and to avoid the complexity of having to determine the egress
border router whose path was chosen as the best in each of the
ingress border routers. It thus becomes necessary to modify step (a)
of the [RFC5575] validation procedure such that an IBGP peer that is
not within the data forwarding plane may originate flow specification
NLRIs.
3. Introduction
[RFC5575] defined a new BGP capability that can be used to distribute
traffic flow specifications amongst BGP speakers in support of
traffic filtering. The primary intention of [RFC5575] is to enable
downstream autonomous systems to signal traffic filtering policies to
upstream autonomous systems. In this way, traffic is filtered closer
to the source and the upstream autonomous system(s) avoid carrying
the traffic to the downstream autonomous system only to be discarded.
[RFC5575] also enables more granular traffic filtering based upon
upper layer protocol information (e.g., protocol port numbers) as
opposed to coarse IP destination prefix-based filtering. Flow
specification NLRIs received from a BGP peer are subject to validity
checks before being considered feasible and subsequently installed
within the respective Adj-RIB-In. The validation procedure defined
within [RFC5575] requires that the originator of the flow
specification NLRI matches the originator of the best-match unicast
route for the destination prefix embedded in the flow specification.
This allows only BGP speakers [RFC4271] within the data forwarding
path (such as autonomous system border routers) to originate BGP flow
specification NLRIs. Though it is possible to disseminate such flow
specification NLRIs directly from border routers, it may be
operationally cumbersome in an autonomous system with a large number
of border routers having complex BGP policies. This document
describes a modification to the [RFC5575] validation procedure
allowing flow specification NLRIs to be originated from a centralized
BGP route controller within the local autonomous system that is not
in the data forwarding path. While the proposed modification cannot
be used for inter-domain coordination of traffic filtering, it
greatly simplifies distribution of intra-domain traffic filtering
policies in an autonomous system with a large number of border
Uttaro, et al. Expires May 9, 2019 [Page 4]
Internet-Draft Revised Flowspec Validation Procedure November 2018
routers having complex BGP policies. By relaxing the validation
procedure for IBGP, the proposed modification allows flow
specifications to be distributed in a standard and scalable manner
throughout an autonomous system.
4. Revised Validation Procedure
Step (a) of the validation procedure specified in [RFC5575], section
6 is redefined as follows:
a. One of the following conditions MUST hold true.
* The originator of the flow specification matches the
originator of the best-match unicast route for the destination
prefix embedded in the flow specification.
* The AS_PATH attribute of the flow specification does not
contain AS_SET and/or AS_SEQUENCE segments.
An AS_PATH without AS_SET and/or AS_SEQUENCE segments indicates that
the flow specification was originated inside the local AS [RFC4271]
or inside the local confederation (in the case that the local AS
belongs to a confederation of ASes) [RFC5065]. With this
modification to the [RFC5575] validation procedure, it is now
possible for an IBGP peer that is not within the data forwarding path
to originate flow specification NLRIs. This applies whether the AS
belongs or not to a confederation of ASes. Checking the (newly
introduced) second condition above MAY be disabled by configuration
on a BGP speaker. However, it SHOULD be enabled by default.
Disabling the condition may be a good practice when the administrator
knows with certainty that there are not flow specification NLRI
originated inside the local AS (or local confederation). The default
behavior is thus to validate an empty AS_PATH. In this context, an
empty AS_PATH means that it does not have AS_SET and/or AS_SEQUENCE
segments. Optionally, an implementation MAY also validate a specific
non-empty AS_PATH. For instance, it could validate a flowspec NLRI
whose AS_PATH contains only an AS_SEQUENCE of ASes known (via
configuration) to belong to the same administrative domain.
Further, [RFC5575] states that "BGP (flow specification)
implementations MUST also enforce that AS_PATH attribute of a route
received via the External Border Gateway Protocol (EBGP) contains the
neighboring AS in the left-most position of the AS_PATH attribute".
This rule is not valid for all topologies. For example, it prevents
the exchange of BGP flow specification NLRIs at Internet exchanges
with BGP route servers. Therefore, this document also redefines the
[RFC5575] AS_PATH validation procedure referenced above as follows:
Uttaro, et al. Expires May 9, 2019 [Page 5]
Internet-Draft Revised Flowspec Validation Procedure November 2018
BGP flow specification implementations MUST enforce that the last AS
added within the AS_PATH attribute of a EBGP learned flow
specification NLRI MUST match the last AS added within the AS_PATH
attribute of the best-match unicast route for the destination prefix
embedded in the flow specification. This proposed modification
enables the exchange of BGP flow specification NLRIs at Internet
exchanges with BGP route servers while at the same time, for security
reasons, prevents an EBGP peer from advertising an inter-domain flow
specification for a destination prefix that it does not provide
reachability information for. Note, comparing only the last ASes
added is sufficient for EBGP learned flow specification NLRIs.
Requiring a full AS_PATH match would limit origination of inter-
domain flow specifications to the origin (or first) AS of the best-
match unicast route for the destination prefix embedded in the flow
specification only. As such, a full AS_PATH validity check may
prevent transit ASes from originating inter-domain flow
specifications, which is not desirable.
This document also clarifies proper handling when the BGP flow
specification does not embed a destination prefix component. The
default behavior SHOULD be not to perform any validation procedure.
Further, support for two-octet AS number space is out of the scope of
this document.
In this context, AS_PATH attribute is defined as the reconstructed AS
Path information (by combining AS_PATH and AS4_PATH attributes, if
the BGP speaker is a NEW speaker and receives the route from an OLD
speaker), according to section 4.2.3 of [RFC6793].
[RFC5575] references "the best-match unicast route for the
destination prefix embedded in the flow specification". For clarity,
this route is defined hereby as the best path of the unicast network
that covers destination prefix embedded in the flow specification
with the longer prefix-length. In other words, we consider only the
best-match network and we do not consider unicast non-best paths
(even if it is received from the same peer than the flowspec route).
Note that, per [RFC5575], originator may refer to the BGP
ORIGINATOR_ID attribute or the transport address of the peer from
which we received the update. If the later, a network must be
designed so it has a congruent topology. Otherwise, using two
peering sessions between the same pair of BGP speakers, one for
unicast and one for flowspec, will cause the flowspec validation
procedure to fail. Consider, for example, the case where a BGP route
reflector receives the NLRIs from a route reflector client, thus not
receiving the ORIGINATOR_ID attribute. If the speaker belongs to a
confederation [RFC5065] and we are receiving a flowspec route from
different peers than its best match unicast route, the flowspec
Uttaro, et al. Expires May 9, 2019 [Page 6]
Internet-Draft Revised Flowspec Validation Procedure November 2018
validation procedure will fail as well. Consider also a
misconfiguration where flowspec address-family is not configured for
a particular peering between different member-AS (but it is
configured for unicast). Even if we receive the flowspec route via a
redundant peer, we may receive the unicast route and the flowspec
from different peers, and thus flowspec validation will fail. Thus,
with the (newly introduced) second condition above applied,
incongruent topologies are supported.
Note that if the flowspec NLRI is learned from another AS (and thus
the AS_PATH is not empty), the original validation procedures defined
in [RFC5575] still apply and incongruent topologies may cause
validation rules to fail.
5. IANA Considerations
This memo includes no request to IANA.
6. Security Considerations
No new security issues are introduced by relaxing the validation
procedure for IBGP learned flow specifications. With this proposal,
the security characteristics of BGP flow specifications remain
equivalent to the existing security properties of BGP unicast
routing. Traffic flow specifications learned from IBGP peers are
trusted, hence, it is not required to validate that the originator of
an intra-domain traffic flow specification matches the originator of
the best-match unicast route for the flow destination prefix.
Conversely, this proposal continues to enforce the validation
procedure for EBGP learned traffic flow specifications. In this way,
the security properties of [RFC5575] are maintained such that an EBGP
peer cannot cause a denial-of-service attack by advertising an inter-
domain flow specification for a destination prefix that it does not
provide reachability information for.
7. Acknowledgements
The authors would like to thank Han Nguyen for his direction on this
work as well as Waqas Alam, Keyur Patel, Robert Raszuk, Eric Rosen
and Shyam Sethuram for their review comments.
8. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
Uttaro, et al. Expires May 9, 2019 [Page 7]
Internet-Draft Revised Flowspec Validation Procedure November 2018
[RFC4271] Rekhter, Y., Ed., Li, T., Ed., and S. Hares, Ed., "A
Border Gateway Protocol 4 (BGP-4)", RFC 4271,
DOI 10.17487/RFC4271, January 2006,
<https://www.rfc-editor.org/info/rfc4271>.
[RFC4456] Bates, T., Chen, E., and R. Chandra, "BGP Route
Reflection: An Alternative to Full Mesh Internal BGP
(IBGP)", RFC 4456, DOI 10.17487/RFC4456, April 2006,
<https://www.rfc-editor.org/info/rfc4456>.
[RFC5065] Traina, P., McPherson, D., and J. Scudder, "Autonomous
System Confederations for BGP", RFC 5065,
DOI 10.17487/RFC5065, August 2007,
<https://www.rfc-editor.org/info/rfc5065>.
[RFC5575] Marques, P., Sheth, N., Raszuk, R., Greene, B., Mauch, J.,
and D. McPherson, "Dissemination of Flow Specification
Rules", RFC 5575, DOI 10.17487/RFC5575, August 2009,
<https://www.rfc-editor.org/info/rfc5575>.
[RFC6793] Vohra, Q. and E. Chen, "BGP Support for Four-Octet
Autonomous System (AS) Number Space", RFC 6793,
DOI 10.17487/RFC6793, December 2012,
<https://www.rfc-editor.org/info/rfc6793>.
Authors' Addresses
James Uttaro
AT&T
200 S. Laurel Ave
Middletown, NJ 07748
USA
Email: ju1738@att.com
Juan Alcaide
Cisco
7100 Kit Creek Road
Research Triangle Park, NC 27709
USA
Email: jalcaide@cisco.com
Uttaro, et al. Expires May 9, 2019 [Page 8]
Internet-Draft Revised Flowspec Validation Procedure November 2018
Clarence Filsfils
Cisco
Email: cf@cisco.com
David Smith
Cisco
111 Wood Ave South
Iselin, NJ 08830
USA
Email: djsmith@cisco.com
Pradosh Mohapatra
Sproute Networks
Email: mpradosh@yahoo.com
Uttaro, et al. Expires May 9, 2019 [Page 9]