DOTS T. Reddy
Internet-Draft McAfee
Intended status: Standards Track M. Boucadair
Expires: May 16, 2018 Orange
P. Patil
Cisco
A. Mortensen
Arbor Networks, Inc.
N. Teague
Verisign, Inc.
November 12, 2017
Distributed Denial-of-Service Open Threat Signaling (DOTS) Signal
Channel
draft-ietf-dots-signal-channel-07
Abstract
This document specifies the DOTS signal channel, a protocol for
signaling the need for protection against Distributed Denial-of-
Service (DDoS) attacks to a server capable of enabling network
traffic mitigation on behalf of the requesting client. A companion
document defines the DOTS data channel, a separate reliable
communication layer for DOTS management and configuration.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on May 16, 2018.
Copyright Notice
Copyright (c) 2017 IETF Trust and the persons identified as the
document authors. All rights reserved.
Reddy, et al. Expires May 16, 2018 [Page 1]
Internet-Draft DOTS Signal Channel November 2017
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Notational Conventions and Terminology . . . . . . . . . . . 3
3. Solution Overview . . . . . . . . . . . . . . . . . . . . . . 4
4. Happy Eyeballs for DOTS Signal Channel . . . . . . . . . . . 5
5. DOTS Signal Channel . . . . . . . . . . . . . . . . . . . . . 6
5.1. Overview . . . . . . . . . . . . . . . . . . . . . . . . 7
5.2. DOTS Signal YANG Module . . . . . . . . . . . . . . . . . 8
5.2.1. Mitigation Request YANG Module Tree Structure . . . . 8
5.2.2. Mitigation Request YANG Module . . . . . . . . . . . 9
5.2.3. Session Configuration YANG Module Tree Structure . . 11
5.2.4. Session Configuration YANG Module . . . . . . . . . . 12
5.3. CoAP URIs . . . . . . . . . . . . . . . . . . . . . . . . 14
5.4. Mitigation Request . . . . . . . . . . . . . . . . . . . 15
5.4.1. Requesting mitigation . . . . . . . . . . . . . . . . 15
5.4.2. Withdraw a DOTS Signal . . . . . . . . . . . . . . . 24
5.4.3. Retrieving a DOTS Signal . . . . . . . . . . . . . . 25
5.4.4. Efficacy Update from DOTS Client . . . . . . . . . . 30
5.5. DOTS Signal Channel Session Configuration . . . . . . . . 32
5.5.1. Discover Configuration Parameters . . . . . . . . . . 33
5.5.2. Convey DOTS Signal Channel Session Configuration . . 35
5.5.3. Delete DOTS Signal Channel Session Configuration . . 39
5.6. Redirected Signaling . . . . . . . . . . . . . . . . . . 40
5.7. Heartbeat Mechanism . . . . . . . . . . . . . . . . . . . 41
6. Mapping parameters to CBOR . . . . . . . . . . . . . . . . . 42
7. (D)TLS Protocol Profile and Performance considerations . . . 43
7.1. MTU and Fragmentation Issues . . . . . . . . . . . . . . 44
8. (D)TLS 1.3 considerations . . . . . . . . . . . . . . . . . . 45
9. Mutual Authentication of DOTS Agents & Authorization of DOTS
Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 48
10.1. DOTS Signal Channel UDP and TCP Port Number . . . . . . 48
10.2. Well-Known 'dots' URI . . . . . . . . . . . . . . . . . 48
10.3. CoAP Response Code . . . . . . . . . . . . . . . . . . . 48
10.4. DOTS signal channel CBOR Mappings Registry . . . . . . . 48
10.4.1. Registration Template . . . . . . . . . . . . . . . 49
10.4.2. Initial Registry Contents . . . . . . . . . . . . . 49
Reddy, et al. Expires May 16, 2018 [Page 2]
Internet-Draft DOTS Signal Channel November 2017
11. Implementation Status . . . . . . . . . . . . . . . . . . . . 54
11.1. nttdots . . . . . . . . . . . . . . . . . . . . . . . . 54
12. Security Considerations . . . . . . . . . . . . . . . . . . . 55
13. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 56
14. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 56
15. References . . . . . . . . . . . . . . . . . . . . . . . . . 56
15.1. Normative References . . . . . . . . . . . . . . . . . . 56
15.2. Informative References . . . . . . . . . . . . . . . . . 57
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 60
1. Introduction
A distributed denial-of-service (DDoS) attack is an attempt to make
machines or network resources unavailable to their intended users.
In most cases, sufficient scale can be achieved by compromising
enough end-hosts and using those infected hosts to perpetrate and
amplify the attack. The victim in this attack can be an application
server, a host, a router, a firewall, or an entire network.
In many cases, it may not be possible for network administrators to
determine the causes of an attack, but instead just realize that
certain resources seem to be under attack. This document defines a
lightweight protocol permitting a DOTS client to request mitigation
from one or more DOTS servers for protection against detected,
suspected, or anticipated attacks . This protocol enables cooperation
between DOTS agents to permit a highly-automated network defense that
is robust, reliable and secure.
The document adheres to the DOTS architecture
[I-D.ietf-dots-architecture]. The requirements for DOTS signal
channel protocol are obtained from [I-D.ietf-dots-requirements].
This document satisfies all the use cases discussed in
[I-D.ietf-dots-use-cases].
This is a companion document to the DOTS data channel specification
[I-D.ietf-dots-data-channel] that defines a configuration and bulk
data exchange mechanism supporting the DOTS signal channel.
2. Notational Conventions and Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in
[RFC2119].
(D)TLS: For brevity this term is used for statements that apply to
both Transport Layer Security [RFC5246] and Datagram Transport Layer
Reddy, et al. Expires May 16, 2018 [Page 3]
Internet-Draft DOTS Signal Channel November 2017
Security [RFC6347]. Specific terms will be used for any statement
that applies to either protocol alone.
The reader should be familiar with the terms defined in
[I-D.ietf-dots-architecture].
3. Solution Overview
Network applications have finite resources like CPU cycles, number of
processes or threads they can create and use, maximum number of
simultaneous connections it can handle, limited resources of the
control plane, etc. When processing network traffic, such
applications are supposed to use these resources to offer the
intended task in the most efficient fashion. However, an attacker
may be able to prevent an application from performing its intended
task by causing the application to exhaust the finite supply of a
specific resource.
TCP DDoS SYN-flood, for example, is a memory-exhaustion attack on the
victim and ACK-flood is a CPU exhaustion attack on the victim
([RFC4987]). Attacks on the link are carried out by sending enough
traffic such that the link becomes excessively congested, and
legitimate traffic suffers high packet loss. Stateful firewalls can
also be attacked by sending traffic that causes the firewall to hold
excessive state. The firewall then runs out of memory, and can no
longer instantiate the state required to pass legitimate flows.
Other possible DDoS attacks are discussed in [RFC4732].
In each of the cases described above, the possible arrangements
between the DOTS client and DOTS server to mitigate the attack are
discussed in [I-D.ietf-dots-use-cases]. An example of network
diagram showing a deployment of these elements is shown in Figure 1.
Architectural relationships between involved DOTS agents is explained
in [I-D.ietf-dots-architecture]. In this example, the DOTS server is
operating on the access network.
Network
Resource CPE router Access network __________
+-----------+ +--------------+ +-------------+ / \
| |____| |_______| |___ | Internet |
|DOTS client| | DOTS gateway | | DOTS server | | |
| | | | | | | |
+-----------+ +--------------+ +-------------+ \__________/
Figure 1: Sample DOTS Deployment (1)
The DOTS server can also be running on the Internet, as depicted in
Figure 2.
Reddy, et al. Expires May 16, 2018 [Page 4]
Internet-Draft DOTS Signal Channel November 2017
Network DDoS mitigation
Resource CPE router __________ service
+-----------+ +-------------+ / \ +-------------+
| |____| |_______| |___ | |
|DOTS client| |DOTS gateway | | Internet | | DOTS server |
| | | | | | | |
+-----------+ +-------------+ \__________/ +-------------+
Figure 2: Sample DOTS Deployment (2)
In typical deployments, the DOTS client belongs to a different
administrative domain than the DOTS server. For example, the DOTS
client is a firewall protecting services owned and operated by an
domain, while the DOTS server is owned and operated by a different
domain providing DDoS mitigation services. That domain providing
DDoS mitigation service might, or might not, also provide Internet
access service to the website operator.
The DOTS server may (not) be co-located with the DOTS mitigator. In
typical deployments, the DOTS server belongs to the same
administrative domain as the mitigator.
The DOTS client can communicate directly with the DOTS server or
indirectly via a DOTS gateway.
This document focuses on the DOTS signal channel.
4. Happy Eyeballs for DOTS Signal Channel
DOTS signaling can happen with DTLS [RFC6347] over UDP and TLS
[RFC5246] over TCP. A DOTS client can use DNS to determine the IP
address(es) of a DOTS server or a DOTS client may be provided with
the list of DOTS server IP addresses. The DOTS client MUST know a
DOTS server's domain name; hard-coding the domain name of the DOTS
server into software is NOT RECOMMENDED in case the domain name is
not valid or needs to change for legal or other reasons. The DOTS
client performs A and/or AAAA record lookup of the domain name and
the result will be a list of IP addresses, each of which can be used
to contact the DOTS server using UDP and TCP.
If an IPv4 path to reach a DOTS server is found, but the DOTS
server's IPv6 path is not working, a dual-stack DOTS client can
experience a significant connection delay compared to an IPv4-only
DOTS client. The other problem is that if a middlebox between the
DOTS client and DOTS server is configured to block UDP, the DOTS
client will fail to establish a DTLS session with the DOTS server and
will, then, have to fall back to TLS over TCP incurring significant
connection delays. [I-D.ietf-dots-requirements] discusses that DOTS
Reddy, et al. Expires May 16, 2018 [Page 5]
Internet-Draft DOTS Signal Channel November 2017
client and server will have to support both connectionless and
connection-oriented protocols.
To overcome these connection setup problems, the DOTS client can try
connecting to the DOTS server using both IPv6 and IPv4, and try both
DTLS over UDP and TLS over TCP in a fashion similar to the Happy
Eyeballs mechanism [RFC6555]. These connection attempts are
performed by the DOTS client when its initializes, and the client
uses that information for its subsequent alert to the DOTS server.
In order of preference (most preferred first), it is UDP over IPv6,
UDP over IPv4, TCP over IPv6, and finally TCP over IPv4, which
adheres to address preference order [RFC6724] and the DOTS preference
that UDP be used over TCP (to avoid TCP's head of line blocking).
DOTS client DOTS server
| |
|--DTLS ClientHello, IPv6 ---->X |
|--TCP SYN, IPv6-------------->X |
|--DTLS ClientHello, IPv4 ---->X |
|--TCP SYN, IPv4----------------------------------------->|
|--DTLS ClientHello, IPv6 ---->X |
|--TCP SYN, IPv6-------------->X |
|<-TCP SYNACK---------------------------------------------|
|--DTLS ClientHello, IPv4 ---->X |
|--TCP ACK----------------------------------------------->|
|<------------Establish TLS Session---------------------->|
|----------------DOTS signal----------------------------->|
| |
Figure 3: Happy Eyeballs
In reference to Figure 3, the DOTS client sends two TCP SYNs and two
DTLS ClientHello messages at the same time over IPv6 and IPv4. In
this example, it is assumed that the IPv6 path is broken and UDP is
dropped by a middlebox but has little impact to the DOTS client
because there is no long delay before using IPv4 and TCP. The DOTS
client repeats the mechanism to discover if DOTS signaling with DTLS
over UDP becomes available from the DOTS server, so the DOTS client
can migrate the DOTS signal channel from TCP to UDP, but such probing
SHOULD NOT be done more frequently than every 24 hours and MUST NOT
be done more frequently than every 5 minutes.
5. DOTS Signal Channel
Reddy, et al. Expires May 16, 2018 [Page 6]
Internet-Draft DOTS Signal Channel November 2017
5.1. Overview
The DOTS signal channel is built on top of the Constrained
Application Protocol (CoAP) [RFC7252], a lightweight protocol
originally designed for constrained devices and networks. CoAP's
expectation of packet loss, support for asynchronous non-confirmable
messaging, congestion control, small message overhead limiting the
need for fragmentation, use of minimal resources, and support for
(D)TLS make it a good foundation on which to build the DOTS signaling
mechanism.
The DOTS signal channel is layered on existing standards (Figure 4).
By default, DOTS signal channel MUST run over port number TBD as
defined in Section 10.1, for both UDP and TCP, unless the DOTS server
has mutual agreement with its DOTS clients to use a port other than
TBD for DOTS signal channel, or DOTS clients supports means to
dynamically discover the ports used by their DOTS servers. In order
to use a distinct port number (vs. TBD), DOTS clients and servers
should support a configurable parameter to supply the port number to
use.
+--------------+
| DOTS |
+--------------+
| CoAP |
+--------------+
| TLS | DTLS |
+--------------+
| TCP | UDP |
+--------------+
| IP |
+--------------+
Figure 4: Abstract Layering of DOTS signal channel over CoAP over
(D)TLS
The signal channel is initiated by the DOTS client. Once the signal
channel is established, the DOTS agents periodically send heartbeats
to keep the channel active. At any time, the DOTS client may send a
mitigation request message to the DOTS server over the active
channel. While mitigation is active, due to the higher likelihood of
packet loss during a DDoS attack, the DOTS server periodically sends
status messages to the client, including basic mitigation feedback
details. Mitigation remains active until the DOTS client explicitly
terminates mitigation, or the mitigation lifetime expires.
Reddy, et al. Expires May 16, 2018 [Page 7]
Internet-Draft DOTS Signal Channel November 2017
Messages exchanged between DOTS client and server are serialized
using Concise Binary Object Representation (CBOR) [RFC7049], CBOR is
a binary encoding designed for small code and message size. CBOR
encoded payloads are used to convey signal channel specific payload
messages that convey request parameters and response information such
as errors. This specification uses the encoding rules defined in
[I-D.ietf-core-yang-cbor] for representing mitigation scope and DOTS
signal channel session configuration data defined using YANG
(Section 5.2) as CBOR data.
DOTS agents MUST support GET, PUT, and DELETE CoAP methods. The
payload included in CoAP responses with 2.xx and 3.xx Response Codes
MUST be of content type "application/cbor" (Section 5.5.1 of
[RFC7252]). CoAP responses with 4.xx and 5.xx error Response Codes
MUST include a diagnostic payload (Section 5.5.2 of [RFC7252]). The
Diagnostic Payload may contain additional information to aid
troubleshooting.
5.2. DOTS Signal YANG Module
This document defines a YANG [RFC6020] module for mitigation scope
and DOTS signal channel session configuration data.
5.2.1. Mitigation Request YANG Module Tree Structure
This document defines the YANG module "ietf-dots-signal", which has
the following tree structure:
module: ietf-dots-signal
+--rw mitigation-scope
+--rw client-identifier* binary
+--rw scope* [mitigation-id]
+--rw mitigation-id int32
+--rw target-ip* inet:ip-address
+--rw target-prefix* inet:ip-prefix
+--rw target-port-range* [lower-port upper-port]
| +--rw lower-port inet:port-number
| +--rw upper-port inet:port-number
+--rw target-protocol* uint8
+--rw fqdn* inet:domain-name
+--rw uri* inet:uri
+--rw alias-name* string
+--rw lifetime? int32
Reddy, et al. Expires May 16, 2018 [Page 8]
Internet-Draft DOTS Signal Channel November 2017
5.2.2. Mitigation Request YANG Module
<CODE BEGINS> file "ietf-dots-signal@2017-10-04.yang"
module ietf-dots-signal {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-dots-signal";
prefix "signal";
import ietf-inet-types {
prefix "inet";
}
organization "IETF DOTS Working Group";
contact
"Konda, Tirumaleswar Reddy <TirumaleswarReddy_Konda@McAfee.com>
Mohamed Boucadair <mohamed.boucadair@orange.com>
Prashanth Patil <praspati@cisco.com>
Andrew Mortensen <amortensen@arbor.net>
Nik Teague <nteague@verisign.com>";
description
"This module contains YANG definition for DOTS
signal sent by the DOTS client to the DOTS server.
Copyright (c) 2017 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2017-10-04 {
description
"Add units and fix some nits.";
reference
"-05";
}
revision 2017-08-03 {
reference
Reddy, et al. Expires May 16, 2018 [Page 9]
Internet-Draft DOTS Signal Channel November 2017
"https://tools.ietf.org/html/draft-reddy-dots-signal-channel";
}
container mitigation-scope {
description
"Top level container for a mitigation request.";
leaf-list client-identifier {
type binary;
description
"A client identifier conveyed by a DOTS gateway
to a remote DOTS server.";
}
list scope {
key mitigation-id;
description "Identifier for the mitigation request.";
leaf mitigation-id {
type int32;
description "Mitigation request identifier.";
}
leaf-list target-ip {
type inet:ip-address;
description
"IPv4 or IPv6 address identifying the target.";
}
leaf-list target-prefix {
type inet:ip-prefix;
description
"IPv4 or IPv6 prefix identifying the target.";
}
list target-port-range {
key "lower-port upper-port";
description "Port range. When only lower-port is present,
it represents a single port.";
leaf lower-port {
type inet:port-number;
mandatory true;
description "Lower port number.";
}
leaf upper-port {
type inet:port-number;
Reddy, et al. Expires May 16, 2018 [Page 10]
Internet-Draft DOTS Signal Channel November 2017
must ". >= ../lower-port" {
error-message
"The upper port number must be greater than or
equal to lower port number.";
}
description "Upper port number.";
}
}
leaf-list target-protocol {
type uint8;
description "Identifies the target protocol number.";
}
leaf-list fqdn {
type inet:domain-name;
description "FQDN";
}
leaf-list uri {
type inet:uri;
description "URI";
}
leaf-list alias-name {
type string;
description "alias name";
}
leaf lifetime {
type int32;
units "seconds";
default 3600;
description
"Indicates the lifetime of the mitigation request.";
}
}
}
}
<CODE ENDS>
5.2.3. Session Configuration YANG Module Tree Structure
This document defines the YANG module "ietf-dots-signal-config",
which has the following structure:
Reddy, et al. Expires May 16, 2018 [Page 11]
Internet-Draft DOTS Signal Channel November 2017
module: ietf-dots-signal-config
+--rw signal-config
+--rw session-id? int32
+--rw heartbeat-interval? int16
+--rw missing-hb-allowed? int16
+--rw max-retransmit? int16
+--rw ack-timeout? int16
+--rw ack-random-factor? decimal64
+--rw trigger-mitigation? boolean
5.2.4. Session Configuration YANG Module
<CODE BEGINS> file "ietf-dots-signal-config@2017-10-04.yang"
module ietf-dots-signal-config {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-dots-signal-config";
prefix "config";
organization "IETF DOTS Working Group";
contact
"Konda, Tirumaleswar Reddy <TirumaleswarReddy_Konda@McAfee.com>
Mohamed Boucadair <mohamed.boucadair@orange.com>
Prashanth Patil <praspati@cisco.com>
Andrew Mortensen <amortensen@arbor.net>
Nik Teague <nteague@verisign.com>";
description
"This module contains YANG definition for DOTS
signal channel session configuration.
Copyright (c) 2017 IETF Trust and the persons identified as
authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision 2017-10-04 {
description
"Add units/defaults and fix some nits.";
Reddy, et al. Expires May 16, 2018 [Page 12]
Internet-Draft DOTS Signal Channel November 2017
reference
"-05";
}
revision 2016-11-28 {
reference
"https://tools.ietf.org/html/draft-reddy-dots-signal-channel";
}
container signal-config {
description "Top level container for DOTS signal channel session
configuration.";
leaf session-id {
type int32;
description "An identifier for the DOTS signal channel
session configuration data.";
}
leaf heartbeat-interval {
type int16;
units "seconds";
default 30;
description
"DOTS agents regularly send heartbeats to each other
after mutual authentication in order to keep
the DOTS signal channel open.";
}
leaf missing-hb-allowed {
type int16;
default 5;
description
"Maximum number of missing heartbeats allowed.";
}
leaf max-retransmit {
type int16;
default 3;
description
"Maximum number of retransmissions of a
Confirmable message.";
}
leaf ack-timeout {
Reddy, et al. Expires May 16, 2018 [Page 13]
Internet-Draft DOTS Signal Channel November 2017
type int16;
units "seconds";
default 2;
description
"Initial retransmission timeout value.";
}
leaf ack-random-factor {
type decimal64 {
fraction-digits 2;
}
default 1.5;
description
"Random factor used to influence the timing of
retransmissions";
}
leaf trigger-mitigation {
type boolean;
default true;
description
"If false, then mitigation is triggered
only when the DOTS server channel session is lost";
}
}
}
<CODE ENDS>
5.3. CoAP URIs
The DOTS server MUST support the use of the path-prefix of "/.well-
known/" as defined in [RFC5785] and the registered name of "dots".
Each DOTS operation is indicated by a path-suffix that indicates the
intended operation.
Reddy, et al. Expires May 16, 2018 [Page 14]
Internet-Draft DOTS Signal Channel November 2017
+------------------------+-----------------+-------------------+
| Operation |Operation path | Details |
+========================+=================+===================+
| Mitigation | /v1/mitigate | Section 5.4 |
| | | |
+------------------------+-----------------+-------------------+
| Session configuration | /v1/config | Section 5.5 |
| | | |
+------------------------+-----------------+-------------------+
Figure 5: Operations and their corresponding URIs:
5.4. Mitigation Request
The following methods are used to request or withdraw mitigation
requests:
PUT: DOTS clients use the PUT method to request mitigation
(Section 5.4.1). During active mitigation, DOTS clients may use
PUT requests to convey mitigation efficacy updates to the DOTS
server (Section 5.4.4).
DELETE: DOTS clients use the DELETE method to withdraw a request for
mitigation from the DOTS server (Section 5.4.2).
GET: DOTS clients may use the GET method to subscribe to DOTS server
status messages, or to retrieve the list of existing mitigations
(Section 5.4.3).
Mitigation request and response messages are marked as Non-
confirmable messages. DOTS agents SHOULD follow the data
transmission guidelines discussed in Section 3.1.3 of [RFC8085] and
control transmission behavior by not sending on average more than one
UDP datagram per RTT to the peer DOTS agent.
Requests marked by the DOTS client as Non-confirmable messages are
sent at regular intervals until a response is received from the DOTS
server and if the DOTS client cannot maintain a RTT estimate then it
SHOULD NOT send more than one Non-confirmable request every 3
seconds, and SHOULD use an even less aggressive rate when possible
(case 2 in Section 3.1.3 of [RFC8085]).
5.4.1. Requesting mitigation
When a DOTS client requires mitigation for any reason, the DOTS
client uses CoAP PUT method to send a mitigation request to the DOTS
server (Figure 6, illustrated in JSON diagnostic notation). The DOTS
server can enable mitigation on behalf of the DOTS client by
Reddy, et al. Expires May 16, 2018 [Page 15]
Internet-Draft DOTS Signal Channel November 2017
communicating the DOTS client's request to the mitigator and relaying
selected mitigator feedback to the requesting DOTS client.
Reddy, et al. Expires May 16, 2018 [Page 16]
Internet-Draft DOTS Signal Channel November 2017
Header: PUT (Code=0.03)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "mitigate"
Content-Type: "application/cbor"
{
"mitigation-scope": {
"client-identifier": [
"string"
],
"scope": [
{
"mitigation-id": integer,
"target-ip": [
"string"
],
"target-prefix": [
"string"
],
"target-port-range": [
{
"lower-port": integer,
"upper-port": integer
}
],
"target-protocol": [
integer
],
"fqdn": [
"string"
],
"uri": [
"string"
],
"alias-name": [
"string"
],
"lifetime": integer
}
]
}
}
Figure 6: PUT to convey DOTS signals
The parameters are described below.
Reddy, et al. Expires May 16, 2018 [Page 17]
Internet-Draft DOTS Signal Channel November 2017
client-identifier: The client identifier MAY be conveyed by the DOTS
gateway to propagate the DOTS client identity from the gateway's
client-side to the gateway's server-side, and from the gateway's
server-side to the DOTS server. This allows the final DOTS server
to accept mitigation requests with scopes which the DOTS client is
authorized to manage.
The 'client-identifier' value MUST be assigned by the DOTS gateway
in a manner that ensures that there is no probability that the
same value will be assigned to a different DOTS client. The DOTS
gateway MUST obscure potentially sensitive DOTS client identity
information. The client-identifier attribute SHOULD NOT to be
generated and included by the DOTS client.
This is an optional attribute.
mitigation-id: Identifier for the mitigation request represented
using an integer. This identifier MUST be unique for each
mitigation request bound to the DOTS client, i.e., the mitigation-
id parameter value in the mitigation request needs to be unique
relative to the mitigation-id parameter values of active
mitigation requests conveyed from the DOTS client to the DOTS
server. This identifier MUST be generated by the DOTS client.
This document does not make any assumption about how this
identifier is generated. This is a mandatory attribute.
target-ip: A list of IP addresses under attack. This is an optional
attribute.
target-prefix: A list of prefixes under attack. Prefixes are
represented using CIDR notation [RFC4632]. This is an optional
attribute.
target-port-range: A list of ports under attack. The port range,
lower-port for lower port number and upper-port for upper port
number. When only lower-port is present, it represents a single
port. For TCP, UDP, Stream Control Transmission Protocol (SCTP)
[RFC4960], or Datagram Congestion Control Protocol (DCCP)
[RFC4340]: the range of ports (e.g., 1024-65535). This is an
optional attribute.
target-protocol: A list of protocols under attack. Values are taken
from the IANA protocol registry [proto_numbers]. The value 0 has
a special meaning for 'all protocols'. This is an optional
attribute.
fqdn: A list of Fully Qualified Domain Names. Fully Qualified
Domain Name (FQDN) is the full name of a system, rather than just
Reddy, et al. Expires May 16, 2018 [Page 18]
Internet-Draft DOTS Signal Channel November 2017
its hostname. For example, "venera" is a hostname, and
"venera.isi.edu" is an FQDN. This is an optional attribute.
uri: A list of Uniform Resource Identifiers (URI). This is an
optional attribute.
alias-name: A list of aliases. Aliases can be created using the
DOTS data channel (Section 3.1.1 of [I-D.ietf-dots-data-channel])
or direct configuration, or other means and then used in
subsequent signal channel exchanges to refer more efficiently to
the resources under attack. This is an optional attribute.
lifetime: Lifetime of the mitigation request in seconds. The
default lifetime of a mitigation request is 3600 seconds (60
minutes) -- this value was chosen to be long enough so that
refreshing is not typically a burden on the DOTS client, while
expiring the request where the client has unexpectedly quit in a
timely manner.
A lifetime of negative one (-1) indicates indefinite lifetime for
the mitigation request.
DOTS clients SHOULD include this parameter in their mitigation
requests. If no lifetime is supplied by a DOTS client, the DOTS
server uses the default lifetime value (3600 seconds). Upon the
expiry of this lifetime, and if the request is not refreshed, the
mitigation request is removed. The request can be refreshed by
sending the same request again. The server MAY refuse indefinite
lifetime, for policy reasons; the granted lifetime value is
returned in the response. DOTS clients MUST be prepared to not be
granted mitigations with indefinite lifetimes. The server MUST
always indicate the actual lifetime in the response and the
remaining lifetime in status messages sent to the client. This is
a mandatory parameter for responses.
The CBOR key values for the parameters are defined in Section 6.
Section 10 defines how the CBOR key values can be allocated to
standards bodies and vendors.
FQDN and URI mitigation scopes may be thought of as a form of scope
alias, in which the addresses to which the domain name or URI resolve
represent the full scope of the mitigation.
In the PUT request at least one of the attributes 'target-ip' or
'target-prefix' or 'fqdn' or 'uri 'or 'alias-name' MUST be present.
DOTS agents can safely ignore Vendor-Specific parameters they don't
understand.
Reddy, et al. Expires May 16, 2018 [Page 19]
Internet-Draft DOTS Signal Channel November 2017
The relative order of two mitigation requests from a DOTS client is
determined by comparing their respective 'mitigation-id' values. If
two mitigation requests have overlapping mitigation scopes, the
mitigation request with higher numeric 'mitigation-id' value will
override the mitigation request with a lower numeric 'mitigation-id'
value. Two mitigation-ids are overlapping if there is a common IP
address, IP prefix, FQDN, URI, or alias-name. The overlapped lower
numeric 'mitigation-id' MUST be automatically deleted and no longer
available at the DOTS server.
The Uri-Path option carries a major and minor version nomenclature to
manage versioning and DOTS signal channel in this specification uses
v1 major version.
If the DOTS client is using the certificate provisioned by the
Enrollment over Secure Transport (EST) server [RFC6234] in the DOTS
gateway-domain to authenticate itself to the DOTS gateway, then the
'client-identifier' value can be the output of a cryptographic hash
algorithm whose input is the DER-encoded ASN.1 representation of the
Subject Public Key Info (SPKI) of an X.509 certificate. In this
version of the specification, the cryptographic hash algorithm used
is SHA-256 [RFC6234]. The output of the cryptographic hash algorithm
is truncated to 16 bytes; truncation is done by stripping off the
final 16 bytes. The truncated output is base64url encoded. If the
'client-identifier' value is already present in the mitigation
request received from the DOTS client, the DOTS gateway MAY compute
the 'client-identifier' value, as discussed above, and add the
computed 'client-identifier' value to the end of the 'client-
identifier' list. The DOTS server MUST NOT use the 'client-
identifier' for the DOTS client authentication process.
In both DOTS signal and data channel sessions, the DOTS client MUST
authenticate itself to the DOTS server (Section 9). The DOTS server
may use the algorithm in Section 7 of [RFC7589] to derive the DOTS
client identity or username from the client certificate. The DOTS
client identity allows the DOTS server to accept mitigation requests
with scopes which the DOTS client is authorized to manage. The DOTS
server couples the DOTS signal and data channel sessions using the
DOTS client identity and the 'client-identifier' parameter value, so
the DOTS server can validate whether the aliases conveyed in the
mitigation request were indeed created by the same DOTS client using
the DOTS data channel session. If the aliases were not created by
the DOTS client, the DOTS server returns 4.00 (Bad Request) in the
response.
The DOTS server couples the DOTS signal channel sessions using the
DOTS client identity and the 'client-identifier' parameter value, and
the DOTS server uses 'mitigation-id' parameter value to detect
Reddy, et al. Expires May 16, 2018 [Page 20]
Internet-Draft DOTS Signal Channel November 2017
duplicate mitigation requests. If the mitigation request contains
both alias-name and other parameters identifying the target resources
(such as, 'target-ip', 'target-prefix', 'target-port-range', 'fqdn',
or 'uri'), then the DOTS server appends the parameter values in
'alias-name' with the corresponding parameter values in 'target-ip',
'target-prefix', 'target-port-range', 'fqdn', or 'uri'.
Figure 7 shows a PUT request example to signal that ports 80, 8080,
and 443 on the servers 2001:db8:6401::1 and 2001:db8:6401::2 are
being attacked (illustrated in JSON diagnostic notation).
Header: PUT (Code=0.03)
Uri-Host: "www.example.com"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "v1"
Uri-Path: "mitigate"
Content-Format: "application/cbor"
{
"mitigation-scope": {
"client-identifier": [
"dz6pHjaADkaFTbjr0JGBpw"
],
"scope": [
{
"mitigation-id": 12332,
"target-ip": [
"2001:db8:6401::1",
"2001:db8:6401::2"
],
"target-port-range": [
{
"lower-port": 80
},
{
"lower-port": 443
},
{
"lower-port": 8080
}
],
"target-protocol": [
6
]
}
]
}
}
Reddy, et al. Expires May 16, 2018 [Page 21]
Internet-Draft DOTS Signal Channel November 2017
The CBOR encoding format is shown below:
A1 # map(1)
01 # unsigned(1)
A2 # map(2)
18 20 # unsigned(32)
81 # array(1)
76 # text(22)
647A3670486A6141446B614654626A72304A47427077 # "dz6pHjaADkaFTbjr0JGBpw"
02 # unsigned(2)
81 # array(1)
A4 # map(4)
03 # unsigned(3)
19 302C # unsigned(12332)
04 # unsigned(4)
82 # array(2)
70 # text(16)
323030313A6462383A363430313A3A31 # "2001:db8:6401::1"
70 # text(16)
323030313A6462383A363430313A3A32 # "2001:db8:6401::2"
05 # unsigned(5)
83 # array(3)
A1 # map(1)
06 # unsigned(6)
18 50 # unsigned(80)
A1 # map(1)
06 # unsigned(6)
19 01BB # unsigned(443)
A1 # map(1)
06 # unsigned(6)
19 1F90 # unsigned(8080)
08 # unsigned(8)
81 # array(1)
06 # unsigned(6)
Figure 7: PUT for DOTS signal
The DOTS server indicates the result of processing the PUT request
using CoAP response codes. CoAP 2.xx codes are success. CoAP 4.xx
codes are some sort of invalid requests. Figure 8 shows a PUT
response for CoAP 2.xx response codes.
Reddy, et al. Expires May 16, 2018 [Page 22]
Internet-Draft DOTS Signal Channel November 2017
{
"mitigation-scope": {
"client-identifier": [
"string"
],
"scope": [
{
"mitigation-id": integer,
"lifetime": integer
}
]
}
}
Figure 8: 2.xx response body
COAP 5.xx codes are returned if the DOTS server has erred or is
currently unavailable to provide mitigation in response to the
mitigation request from the DOTS client.
If the DOTS server does not find the 'mitigation-id' parameter value
conveyed in the PUT request in its configuration data, then the
server MAY accept the mitigation request by sending back a 2.01
(Created) response to the DOTS client; the DOTS server will
consequently try to mitigate the attack.
If the DOTS server finds the 'mitigation-id' parameter value conveyed
in the PUT request in its configuration data, then the server MAY
update the mitigation request, and a 2.04 (Changed) response is
returned to indicate a successful update of the mitigation request.
If the request is missing one or more mandatory attributes, then 4.00
(Bad Request) will be returned in the response or if the request
contains invalid or unknown parameters then 4.02 (Invalid query) is
returned in the response.
For a mitigation request to continue beyond the initial negotiated
lifetime, the DOTS client need to refresh the current mitigation
request by sending a new PUT request. The PUT request MUST use the
same 'mitigation-id' value, and MUST repeat all the other parameters
as sent in the original mitigation request apart from a possible
change to the lifetime parameter value.
A DOTS gateway MUST update the 'client-identifier' list in the
response to remove the 'client-identifier' value it had added in the
corresponding request before forwarding the response to the DOTS
client.
Reddy, et al. Expires May 16, 2018 [Page 23]
Internet-Draft DOTS Signal Channel November 2017
5.4.2. Withdraw a DOTS Signal
A DELETE request is used to withdraw a DOTS signal from a DOTS server
(Figure 9).
Header: DELETE (Code=0.04)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "mitigate"
Content-Format: "application/cbor"
{
"mitigation-scope": {
"client-identifier": [
"string"
],
"scope": [
{
"mitigation-id": integer
}
]
}
}
Figure 9: Withdraw DOTS signal
The DOTS server immediately acknowledges a DOTS client's request to
withdraw the DOTS signal using 2.02 (Deleted) response code with no
response payload. A 2.02 (Deleted) Response Code is returned even if
the 'mitigation-id' parameter value conveyed in the DELETE request
does not exist in its configuration data before the request.
If the DOTS server finds the 'mitigation-id' parameter value conveyed
in the DELETE request in its configuration data, then to protect
against route or DNS flapping caused by a client rapidly toggling
mitigation, and to dampen the effect of oscillating attacks, DOTS
servers MAY allow mitigation to continue for a limited period after
acknowledging a DOTS client's withdrawal of a mitigation request.
During this period, the DOTS server status messages SHOULD indicate
that mitigation is active but terminating. The initial active-but-
terminating period SHOULD be sufficiently long to absorb latency
incurred by route propagation. The active-but-terminating period
SHOULD be set by default to 120 seconds. If the client requests
mitigation again before the initial active-but-terminating period
elapses, the DOTS server MAY exponentially increase the active-but-
terminating period up to a maximum of 300 seconds (5 minutes). After
the active-but-terminating period elapses, the DOTS server MUST treat
Reddy, et al. Expires May 16, 2018 [Page 24]
Internet-Draft DOTS Signal Channel November 2017
the mitigation as terminated, as the DOTS client is no longer
responsible for the mitigation. For example, if there is a financial
relationship between the DOTS client and server domains, the DOTS
client ceases incurring cost at this point.
5.4.3. Retrieving a DOTS Signal
A GET request is used to retrieve information (including status) of a
DOTS signal from a DOTS server (Figure 10). If the DOTS server does
not find the 'mitigation-id' parameter value conveyed in the GET
request in its configuration data, then it responds with a 4.04 (Not
Found) error response code. The 'c' (content) parameter and its
permitted values defined in [I-D.ietf-core-comi] can be used to
retrieve non-configuration data (attack mitigation status) or
configuration data or both. The DOTS server SHOULD support this
optional filtering capability but can safely ignore it if not
supported.
The examples below assume the default of "c=a".
Reddy, et al. Expires May 16, 2018 [Page 25]
Internet-Draft DOTS Signal Channel November 2017
1) To retrieve all DOTS signals signaled by the DOTS client.
Header: GET (Code=0.01)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "mitigate"
Observe : 0
{
"mitigation-scope": {
"client-identifier": [
"string"
]
}
}
2) To retrieve a specific DOTS signal signaled by the DOTS client.
The configuration data in the response will be formatted in the
same order it was processed at the DOTS server.
Header: GET (Code=0.01)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "mitigate"
Observe : 0
Content-Format: "application/cbor"
{
"mitigation-scope": {
"client-identifier": [
"string"
],
"scope": [
{
"mitigation-id": integer
}
]
}
}
Figure 10: GET to retrieve the rules
Figure 11 shows a response example of all the active mitigation
requests associated with the DOTS client on the DOTS server and the
mitigation status of each mitigation request.
Reddy, et al. Expires May 16, 2018 [Page 26]
Internet-Draft DOTS Signal Channel November 2017
{
"mitigation-scope": {
"scope": [
{
"mitigation-id": 12332,
"mitigation-start": 1507818434.00,
"target-protocol": [
17
],
"lifetime":1800,
"status":2,
"bytes-dropped": 134334555,
"bps-dropped": 43344,
"pkts-dropped": 333334444,
"pps-dropped": 432432
},
{
"mitigation-id": 12333,
"mitigation-start": 1507818393.00,
"target-protocol": [
6
],
"lifetime":1800,
"status":3
"bytes-dropped": 0,
"bps-dropped": 0,
"pkts-dropped": 0,
"pps-dropped": 0
}
]
}
}
Figure 11: Response body
The mitigation status parameters are described below.
lifetime: The remaining lifetime of the mitigation request in
seconds.
mitigation-start: Mitigation start time is represented in seconds
relative to 1970-01-01T00:00Z in UTC time (Section 2.4.1 of
[RFC7049]). The encoding is modified so that the leading tag 1
(epoch-based date/time) MUST be omitted.
bytes-dropped: The total dropped byte count for the mitigation
request since the attack mitigation is triggered. The count wraps
Reddy, et al. Expires May 16, 2018 [Page 27]
Internet-Draft DOTS Signal Channel November 2017
around when it reaches the maximum value of unsigned integer.
This is an optional attribute.
bps-dropped: The average dropped bytes per second for the mitigation
request since the attack mitigation is triggered. This SHOULD be
a five-minute average. This is an optional attribute.
pkts-dropped: The total dropped packet count for the mitigation
request since the attack mitigation is triggered. This is an
optional attribute.
pps-dropped: The average dropped packets per second for the
mitigation request since the attack mitigation is triggered. This
SHOULD be a five-minute average. This is an optional attribute.
status: Status of attack mitigation. The 'status' parameter is a
mandatory attribute.
The various possible values of 'status' parameter are explained
below:
/--------------------+---------------------------------------------------\
| Parameter value | Description |
+--------------------+---------------------------------------------------+
| 1 | Attack mitigation is in progress |
| | (e.g., changing the network path to re-route the |
| | inbound traffic to DOTS mitigator). |
+--------------------+---------------------------------------------------+
| 2 | Attack is successfully mitigated |
| | (e.g., traffic is redirected to a DDOS mitigator |
| | and attack traffic is dropped). |
+--------------------+---------------------------------------------------+
| 3 | Attack has stopped and the DOTS client |
| | can withdraw the mitigation request. |
+--------------------+---------------------------------------------------+
| 4 | Attack has exceeded the mitigation provider |
| | capability. |
+--------------------+---------------------------------------------------+
| 5 | DOTS client has withdrawn the mitigation request |
| | and the mitigation is active but terminating. |
\--------------------+---------------------------------------------------/
The observe option defined in [RFC7641] extends the CoAP core
protocol with a mechanism for a CoAP client to "observe" a resource
on a CoAP server: the client retrieves a representation of the
resource and requests this representation be updated by the server as
long as the client is interested in the resource. A DOTS client
Reddy, et al. Expires May 16, 2018 [Page 28]
Internet-Draft DOTS Signal Channel November 2017
conveys the observe option set to 0 in the GET request to receive
unsolicited notifications of attack mitigation status from the DOTS
server. Unidirectional notifications within the bidirectional signal
channel allows unsolicited message delivery, enabling asynchronous
notifications between the agents. Due to the higher likelihood of
packet loss during a DDoS attack, DOTS server periodically sends
attack mitigation status to the DOTS client and also notifies the
DOTS client whenever the status of the attack mitigation changes. If
the DOTS server cannot maintain a RTT estimate then it SHOULD NOT
send more than one unsolicited notification every 3 seconds, and
SHOULD use an even less aggressive rate when possible (case 2 in
Section 3.1.3 of [RFC8085]). A DOTS client that is no longer
interested in receiving notifications from the DOTS server can simply
"forget" the observation. When the DOTS server then sends the next
notification, the DOTS client will not recognize the token in the
message and thus will return a Reset message. This causes the DOTS
server to remove the associated entry. Alternatively, the DOTS
client can explicitly deregister by issuing a GET request that has
the Token field set to the token of the observation to be cancelled
and includes an Observe Option with the value set to 1 (deregister).
DOTS Client DOTS Server
| |
| GET /<mitigation-id number> |
| Token: 0x4a | Registration
| Observe: 0 |
+------------------------------>|
| |
| 2.05 Content |
| Token: 0x4a | Notification of
| Observe: 12 | the current state
| status: "mitigation |
| in progress" |
|<------------------------------+
| 2.05 Content |
| Token: 0x4a | Notification upon
| Observe: 44 | a state change
| status: "mitigation |
| complete" |
|<------------------------------+
| 2.05 Content |
| Token: 0x4a | Notification upon
| Observe: 60 | a state change
| status: "attack stopped" |
|<------------------------------+
| |
Figure 12: Notifications of attack mitigation status
Reddy, et al. Expires May 16, 2018 [Page 29]
Internet-Draft DOTS Signal Channel November 2017
5.4.3.1. Mitigation Status
The DOTS client can send the GET request at frequent intervals
without the Observe option to retrieve the configuration data of the
mitigation request and non-configuration data (i.e., the attack
status). The frequency of polling the DOTS server to get the
mitigation status should follow the transmission guidelines given in
Section 3.1.3 of [RFC8085]. If the DOTS server has been able to
mitigate the attack and the attack has stopped, the DOTS server
indicates as such in the status, and the DOTS client recalls the
mitigation request by issuing a DELETE for the mitigation-id.
A DOTS client should react to the status of the attack from the DOTS
server and not the fact that it has recognized, using its own means,
that the attack has been mitigated. This ensures that the DOTS
client does not recall a mitigation request in a premature fashion
because it is possible that the DOTS client does not sense the DDOS
attack on its resources but the DOTS server could be actively
mitigating the attack and the attack is not completely averted.
5.4.4. Efficacy Update from DOTS Client
While DDoS mitigation is active, due to the likelihood of packet
loss, a DOTS client MAY periodically transmit DOTS mitigation
efficacy updates to the relevant DOTS server. A PUT request
(Figure 13) is used to convey the mitigation efficacy update to the
DOTS server.
The PUT request MUST include all the parameters used in the PUT
request to convey the DOTS signal (Section 5.4.1) unchanged apart
from the lifetime parameter value. If this is not the case, the DOTS
server MUST reject the request with a 4.02 error response code.
The If-Match Option (Section 5.10.8.1 of [RFC7252]) with an empty
value is used to make the PUT request conditional on the current
existence of the mitigation request. If UDP is used as transport,
CoAP requests may arrive out-of-order. For example, the DOTS client
may send a PUT request to convey an efficacy update to the DOTS
server followed by a DELETE request to withdraw the mitigation
request, but the DELETE request arrives at the DOTS server before the
PUT request. To handle out-of-order delivery of requests, if an If-
Match option is present in the PUT request and the 'mitigation-id' in
the request matches a mitigation request from that DOTS client, then
the request is processed. If no match is found, the PUT request is
silently ignored.
Reddy, et al. Expires May 16, 2018 [Page 30]
Internet-Draft DOTS Signal Channel November 2017
Header: PUT (Code=0.03)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "mitigate"
Content-Format: "application/cbor"
{
"mitigation-scope": {
"client-identifier": [
"string"
],
"scope": [
{
"mitigation-id": integer,
"target-ip": [
"string"
],
"target-port-range": [
{
"lower-port": integer,
"upper-port": integer
}
],
"target-protocol": [
integer
],
"fqdn": [
"string"
],
"uri": [
"string"
],
"alias-name": [
"string"
],
"lifetime": integer,
"attack-status": integer
}
]
}
}
Figure 13: Efficacy Update
The 'attack-status' parameter is a mandatory attribute when doing a
efficacy update. The various possible values contained in the
'attack-status' parameter are described below:
Reddy, et al. Expires May 16, 2018 [Page 31]
Internet-Draft DOTS Signal Channel November 2017
/--------------------+------------------------------------------------------\
| Parameter value | Description |
+--------------------+------------------------------------------------------+
| 1 | DOTS client determines that it is still under attack.|
+--------------------+------------------------------------------------------+
| 2 | DOTS client determines that the attack is |
| | successfully mitigated |
| | (e.g., attack traffic is not seen). |
\--------------------+------------------------------------------------------/
The DOTS server indicates the result of processing a PUT request
using CoAP response codes. The response code 2.04 (Changed) is
returned if the DOTS server has accepted the mitigation efficacy
update. The error response code 5.03 (Service Unavailable) is
returned if the DOTS server has erred or is incapable of performing
the mitigation.
5.5. DOTS Signal Channel Session Configuration
The DOTS client can negotiate, configure, and retrieve the DOTS
signal channel session behavior. The DOTS signal channel can be
used, for example, to configure the following:
a. Heartbeat interval: DOTS agents regularly send heartbeats (CoAP
Ping/Pong) to each other after mutual authentication in order to
keep the DOTS signal channel open, heartbeat messages are
exchanged between the DOTS agents every heartbeat-interval
seconds to detect the current status of the DOTS signal channel
session.
b. Missing heartbeats allowed: This variable indicates the maximum
number of consecutive heartbeat messages for which a DOTS agent
did not receive a response before concluding that the session is
disconnected or defunct.
c. Acceptable signal loss ratio: Maximum retransmissions,
retransmission timeout value and other message transmission
parameters for the DOTS signal channel.
Reliability is provided to requests and responses by marking them as
Confirmable (CON) messages. DOTS signal channel session
configuration requests and responses are marked as Confirmable (CON)
messages. As explained in Section 2.1 of [RFC7252], a Confirmable
message is retransmitted using a default timeout and exponential
back-off between retransmissions, until the DOTS server sends an
Acknowledgement message (ACK) with the same Message ID conveyed from
the DOTS client. Message transmission parameters are defined in
Reddy, et al. Expires May 16, 2018 [Page 32]
Internet-Draft DOTS Signal Channel November 2017
Section 4.8 of [RFC7252]. Reliability is provided to the responses
by marking them as Confirmable (CON) messages. The DOTS server can
either piggyback the response in the acknowledgement message or if
the DOTS server is not able to respond immediately to a request
carried in a Confirmable message, it simply responds with an Empty
Acknowledgement message so that the DOTS client can stop
retransmitting the request. Empty Acknowledgement message is
explained in Section 2.2 of [RFC7252]. When the response is ready,
the server sends it in a new Confirmable message which then in turn
needs to be acknowledged by the DOTS client (see Sections 5.2.1 and
Sections 5.2.2 of [RFC7252]). Requests and responses exchanged
between DOTS agents during peacetime are marked as Confirmable
messages.
Implementation Note: A DOTS client that receives a response in a CON
message may want to clean up the message state right after sending
the ACK. If that ACK is lost and the DOTS server retransmits the
CON, the DOTS client may no longer have any state to which to
correlate this response, making the retransmission an unexpected
message; the DOTS client will send a Reset message so it does not
receive any more retransmissions. This behavior is normal and not an
indication of an error (see Section 5.3.2 of [RFC7252] for more
details).
5.5.1. Discover Configuration Parameters
A GET request is used to obtain acceptable and current configuration
parameters on the DOTS server for DOTS signal channel session
configuration. Figure 14 shows how to obtain acceptable
configuration parameters for the server.
Header: GET (Code=0.01)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "config"
Figure 14: GET to retrieve configuration
The DOTS server in the 2.05 (Content) response conveys the current,
minimum and maximum attribute values acceptable by the DOTS server.
Reddy, et al. Expires May 16, 2018 [Page 33]
Internet-Draft DOTS Signal Channel November 2017
Content-Format: "application/cbor"
{
"heartbeat-interval": {
"CurrentValue": integer,
"MinValue": integer,
"MaxValue" : integer,
},
"missing-hb-allowed": {
"CurrentValue": integer,
"MinValue": integer,
"MaxValue" : integer,
},
"max-retransmit": {
"CurrentValue": integer,
"MinValue": integer,
"MaxValue" : integer,
},
"ack-timeout": {
"CurrentValue": integer,
"MinValue": integer,
"MaxValue" : integer,
},
"ack-random-factor": {
"CurrentValue": number,
"MinValue": number,
"MaxValue" : number,
},
"trigger-mitigation": {
"CurrentValue": boolean,
}
}
Figure 15: GET response body
Figure 16 shows an example of acceptable and current configuration
parameters on the DOTS server for DOTS signal channel session
configuration.
Reddy, et al. Expires May 16, 2018 [Page 34]
Internet-Draft DOTS Signal Channel November 2017
Content-Format: "application/cbor"
{
"heartbeat-interval": {
"CurrentValue": 30,
"MinValue": 15,
"MaxValue" : 240,
},
"missing-hb-allowed": {
"CurrentValue": 5,
"MinValue": 3,
"MaxValue" : 9,
},
"max-retransmit": {
"CurrentValue": 3,
"MinValue": 2,
"MaxValue" : 15,
},
"ack-timeout": {
"CurrentValue": 2,
"MinValue": 1,
"MaxValue" : 30,
},
"ack-random-factor": {
"CurrentValue": 1.5,
"MinValue": 1.1,
"MaxValue" : 4.0,
},
"trigger-mitigation": {
"CurrentValue": true,
}
}
Figure 16: configuration response body
5.5.2. Convey DOTS Signal Channel Session Configuration
A PUT request is used to convey the configuration parameters for the
signaling channel (e.g., heartbeat interval, maximum
retransmissions). Message transmission parameters for CoAP are
defined in Section 4.8 of [RFC7252]. The RECOMMENDED values of
transmission parameter values are ack_timeout (2 seconds), max-
retransmit (3), ack-random-factor (1.5). In addition to those
parameters, the RECOMMENDED specific DOTS transmission parameter
values are heartbeat-interval (30 seconds) and missing-hb-allowed
(5).
Note: heartbeat-interval should be tweaked to also assist DOTS
messages for NAT traversal (SIG-010 of
Reddy, et al. Expires May 16, 2018 [Page 35]
Internet-Draft DOTS Signal Channel November 2017
[I-D.ietf-dots-requirements]). According to [RFC8085], keepalive
messages must not be sent more frequently than once every 15
seconds and should use longer intervals when possible.
Furthermore, [RFC4787] recommends NATs to use a state timeout of 2
minutes or longer, but experience shows that sending packets every
15 to 30 seconds is necessary to prevent the majority of
middleboxes from losing state for UDP flows. From that
standpoint, this specification recommends a minimum heartbeat-
interval of 15 seconds and a maximum heartbeat-interval of 240
seconds. The recommended value of 30 seconds is selected to
anticipate the expiry of NAT state.
A heartbeat-interval of 30 second may be seen as too chatty in
some deployments. For such deployments, DOTS agents may negotiate
longer heartbeat-interval values to avoid overloading the network
with too frequent keepalives.
When a confirmable "CoAP ping" is sent, and if there is no response,
the "CoAP ping" will get retransmitted max-retransmit number of times
by the CoAP layer using an initial timeout set to a random duration
between ack_timeout and (ack-timeout*ack-random-factor) and
exponential back-off between retransmissions. By choosing the
recommended transmission parameters, the "CoAP ping" will timeout
after 45 seconds. If the DOTS agent does not receive any response
from the peer DOTS agent for missing-hb-allowed number of consecutive
"CoAP ping" confirmable messages, then it concludes that the DOTS
signal channel session is disconnected. A DOTS client MUST NOT
transmit a "CoAP ping" while waiting for the previous "CoAP ping"
response from the same DOTS server.
If the DOTS agent wishes to change the default values of message
transmission parameters, then it should follow the guidance given in
Section 4.8.1 of [RFC7252]. The DOTS agents MUST use the negotiated
values for message transmission parameters and default values for
non-negotiated message transmission parameters.
The signaling channel session configuration is applicable to a single
DOTS signal channel session between the DOTS agents.
Reddy, et al. Expires May 16, 2018 [Page 36]
Internet-Draft DOTS Signal Channel November 2017
Header: PUT (Code=0.03)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "config"
Content-Format: "application/cbor"
{
"signal-config": {
"session-id": integer,
"heartbeat-interval": integer,
"missing-hb-allowed": integer,
"max-retransmit": integer,
"ack-timeout": integer,
"ack-random-factor": number
"trigger-mitigation": boolean
}
}
Figure 17: PUT to convey the DOTS signal channel session
configuration data.
The parameters are described below:
session-id: Identifier for the DOTS signal channel session
configuration data represented as an integer. This identifier
MUST be generated by the DOTS client. This document does not make
any assumption about how this identifier is generated. This is a
mandatory attribute.
heartbeat-interval: Time interval in seconds between two
consecutive heartbeat messages. This is an optional attribute.
missing-hb-allowed: Maximum number of consecutive heartbeat
messages for which the DOTS agent did not receive a response
before concluding that the session is disconnected. This is an
optional attribute.
max-retransmit: Maximum number of retransmissions for a message
(referred to as MAX_RETRANSMIT parameter in CoAP). This is an
optional attribute.
ack-timeout: Timeout value in seconds used to calculate the initial
retransmission timeout value (referred to as ACK_TIMEOUT parameter
in CoAP). This is an optional attribute.
Reddy, et al. Expires May 16, 2018 [Page 37]
Internet-Draft DOTS Signal Channel November 2017
ack-random-factor: Random factor used to influence the timing of
retransmissions (referred to as ACK_RANDOM_FACTOR parameter in
CoAP). This is an optional attribute.
trigger-mitigation: If the parameter value is set to 'false', then
DDoS mitigation is triggered only when the DOTS signal channel
session is lost. Automated mitigation on loss of signal is
discussed in Section 3.3.3 of [I-D.ietf-dots-architecture]. If
the DOTS client ceases to respond to heartbeat messages, then the
DOTS server can detect that the DOTS session is lost. The default
value of the parameter is 'true'. This is an optional attribute.
In the PUT request at least one of the attributes heartbeat-interval,
missing-hb-allowed, max-retransmit, ack-timeout, ack-random-factor,
and trigger-mitigation MUST be present. The PUT request with higher
numeric session-id value over-rides the DOTS signal channel session
configuration data installed by a PUT request with a lower numeric
session-id value.
Figure 18 shows a PUT request example to convey the configuration
parameters for the DOTS signal channel.
Header: PUT (Code=0.03)
Uri-Host: "www.example.com"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "v1"
Uri-Path: "config"
Content-Format: "application/cbor"
{
"signal-config": {
"session-id": 1234534333242,
"heartbeat-interval": 91,
"missing-hb-allowed": 3,
"max-retransmit": 7,
"ack-timeout": 5,
"ack-random-factor": 1.5,
"trigger-mitigation": false
}
}
Figure 18: PUT to convey the configuration parameters
The DOTS server indicates the result of processing the PUT request
using CoAP response codes:
o If the DOTS server finds the 'session-id' parameter value conveyed
in the PUT request in its configuration data and if the DOTS
Reddy, et al. Expires May 16, 2018 [Page 38]
Internet-Draft DOTS Signal Channel November 2017
server has accepted the updated configuration parameters, then
2.04 (Changed) code is returned in the response.
o If the DOTS server does not find the 'session-id' parameter value
conveyed in the PUT request in its configuration data and if the
DOTS server has accepted the configuration parameters, then a
response code 2.01 (Created) is returned in the response.
o If the request is missing one or more mandatory attributes, then
4.00 (Bad Request) is returned in the response.
o If the request contains one or more invalid or unknown parameters,
then 4.02 (Invalid query) code is returned in the response.
o Response code 4.22 (Unprocessable Entity) is returned in the
response, if any of the heartbeat-interval, missing-hb-allowed,
max-retransmit, target-protocol, ack-timeout, and ack-random-
factor attribute values are not acceptable to the DOTS server.
Upon receipt of the 4.22 error response code, the DOTS client
should request the maximum and minimum attribute values acceptable
to the DOTS server (Section 5.5.1). The DOTS client may re-try
and send the PUT request with updated attribute values acceptable
to the DOTS server.
5.5.3. Delete DOTS Signal Channel Session Configuration
A DELETE request is used to delete the installed DOTS signal channel
session configuration data (Figure 19).
Header: DELETE (Code=0.04)
Uri-Host: "host"
Uri-Path: ".well-known"
Uri-Path: "dots"
Uri-Path: "version"
Uri-Path: "config"
Content-Format: "application/cbor"
Figure 19: DELETE configuration
The DOTS server resets the DOTS signal channel session configuration
back to the default values and acknowledges a DOTS client's request
to remove the DOTS signal channel session configuration using 2.02
(Deleted) response code.
Reddy, et al. Expires May 16, 2018 [Page 39]
Internet-Draft DOTS Signal Channel November 2017
5.6. Redirected Signaling
Redirected Signaling is discussed in detail in Section 3.2.2 of
[I-D.ietf-dots-architecture]. If the DOTS server wants to redirect
the DOTS client to an alternative DOTS server for a signaling session
then the response code 3.00 (alternate server) will be returned in
the response to the client. The DOTS server can return the error
response code 3.00 in response to a PUT request from the DOTS client
or convey the error response code 3.00 in a unidirectional
notification response from the DOTS server.
The DOTS server in the error response conveys the alternate DOTS
server FQDN, and the alternate DOTS server IP addresses and time to
live values in the CBOR body.
{
"alt-server": "string",
"alt-server-record": [
{
"addr": "string",
"ttl" : integer,
}
]
}
Figure 20: Error response body
The parameters are described below:
alt-server: FQDN of an alternate DOTS server.
addr: IP address of an alternate DOTS server.
ttl: Time to live (TTL) represented as an integer number of seconds.
Figure 21 shows a 3.00 response example to convey the DOTS alternate
server www.example-alt.com, its IP addresses 2001:db8:6401::1 and
2001:db8:6401::2, and TTL values 3600 and 1800.
Reddy, et al. Expires May 16, 2018 [Page 40]
Internet-Draft DOTS Signal Channel November 2017
{
"alt-server": "www.example-alt.com",
"alt-server-record": [
{
"ttl" : 3600,
"addr": "2001:db8:6401::1"
},
{
"ttl" : 1800,
"addr": "2001:db8:6401::2"
}
]
}
Figure 21: Example of error response body
When the DOTS client receives 3.00 response, it considers the current
request as having failed, but SHOULD try the request with the
alternate DOTS server. During a DDOS attack, the DNS server may be
subjected to DDOS attack, alternate DOTS server IP addresses conveyed
in the 3.00 response help the DOTS client to skip DNS lookup of the
alternate DOTS server and can try to establish UDP or TCP session
with the alternate DOTS server IP addresses. The DOTS client SHOULD
implement DNS64 function to handle the scenario where IPv6-only DOTS
client communicates with IPv4-only alternate DOTS server.
5.7. Heartbeat Mechanism
To provide a metric of signal health and distinguish an 'idle' signal
channel from a 'disconnected' or 'defunct' session, the DOTS agent
sends a heartbeat over the signal channel to maintain its half of the
channel. The DOTS agent similarly expects a heartbeat from its peer
DOTS agent, and may consider a session terminated in the extended
absence of a peer agent heartbeat.
While the communication between the DOTS agents is quiescent, the
DOTS client will probe the DOTS server to ensure it has maintained
cryptographic state and vice versa. Such probes can also keep alive
firewall and/or NAT bindings. This probing reduces the frequency of
establishing a new handshake when a DOTS signal needs to be conveyed
to the DOTS server.
In case of a volumetric DDoS attack saturating the incoming link to
the DOTS client, all traffic from the DOTS server to the DOTS client
will likely be dropped, although the DOTS server receives heartbeat
requests and DOTS messages from the DOTS client. In this scenario,
Reddy, et al. Expires May 16, 2018 [Page 41]
Internet-Draft DOTS Signal Channel November 2017
the DOTS agents MUST behave differently to handle message
transmission and DOTS session liveliness during link saturation:
o The DOTS client MUST NOT consider the DOTS session terminated even
after maximum "missing-hb-allowed" threshold is reached. The DOTS
client SHOULD continue to use the current DOTS session, and send
heartbeat requests over the current DOTS session, so the DOTS
server knows the DOTS client has not disconnected the DOTS
session. After the maximum "missing-hb-allowed" threshold is
reached, the DOTS client SHOULD try (D)TLS session resumption.
The DOTS client SHOULD send mitigation requests over the current
DOTS session, and in parallel, try (D)TLS session resumption or
0-RTT mode in DTLS 1.3 to piggyback the mitigation request in the
ClientHello message. Once the link is no longer statured, if
traffic from the DOTS server reaches the DOTS client over the
current DOTS session, the DOTS client can stop (D)TLS session
resumption or if (D)TLS session resumption is successful then
disconnect the current DOTS session.
o If the DOTS server does not receive any traffic from the peer DOTS
client, then the DOTS server sends heartbeat requests to the DOTS
client and after maximum "missing-hb-allowed" threshold is
reached, the DOTS server concludes the session is disconnected.
In DOTS over UDP, heartbeat messages may be exchanged between the
DOTS agents using the "COAP ping" mechanism defined in Section 4.2 of
[RFC7252]. Concretely, the DOTS agent sends an Empty Confirmable
message and the peer DOTS agent will respond by sending an Reset
message.
In DOTS over TCP, heartbeat messages can be exchanged between the
DOTS agents using the Ping and Pong messages specified in Section 4.4
of [I-D.ietf-core-coap-tcp-tls]. That is, the DOTS agent sends a
Ping message and the peer DOTS agent would respond by sending a
single Pong message.
6. Mapping parameters to CBOR
All parameters in the payload in the DOTS signal channel MUST be
mapped to CBOR types as follows and are given an integer key to save
space. The recipient of the payload MAY reject the information if it
is not suitably mapped.
Reddy, et al. Expires May 16, 2018 [Page 42]
Internet-Draft DOTS Signal Channel November 2017
/--------------------+------------------------+--------------------------\
| Parameter name | CBOR key | CBOR major type of value |
+--------------------+------------------------+--------------------------+
| mitigation-scope | 1 | 5 (map) |
| scope | 2 | 5 (map) |
| mitigation-id | 3 | 0 (unsigned) |
| target-ip | 4 | 4 (array) |
| target-port-range | 5 | 4 |
| lower-port | 6 | 0 |
| upper-port | 7 | 0 |
| target-protocol | 8 | 4 |
| fqdn | 9 | 4 |
| uri | 10 | 4 |
| alias-name | 11 | 4 |
| lifetime | 12 | 0 |
| attack-status | 13 | 0 |
| signal-config | 14 | 5 |
| heartbeat-interval | 15 | 0 |
| max-retransmit | 16 | 0 |
| ack-timeout | 17 | 0 |
| ack-random-factor | 18 | 7 |
| MinValue | 19 | 0 |
| MaxValue | 20 | 0 |
| status | 21 | 0 |
| bytes-dropped | 22 | 0 |
| bps-dropped | 23 | 0 |
| pkts-dropped | 24 | 0 |
| pps-dropped | 25 | 0 |
| session-id | 26 | 0 |
| trigger-mitigation | 27 | 7 (simple types) |
| missing-hb-allowed | 28 | 0 |
| CurrentValue | 29 | 0 |
| mitigation-start | 30 | 7 (floating-point) |
| target-prefix | 31 | 4 (array) |
| client-identifier | 32 | 2 (byte string) |
| alt-server | 33 | 2 |
| alt-server-record | 34 | 4 |
| addr | 35 | 2 |
| ttl | 36 | 0 |
\--------------------+------------------------+--------------------------/
Figure 22: CBOR mappings used in DOTS signal channel message
7. (D)TLS Protocol Profile and Performance considerations
This section defines the (D)TLS protocol profile of DOTS signal
channel over (D)TLS and DOTS data channel over TLS.
Reddy, et al. Expires May 16, 2018 [Page 43]
Internet-Draft DOTS Signal Channel November 2017
There are known attacks on (D)TLS, such as machine-in-the-middle and
protocol downgrade. These are general attacks on (D)TLS and not
specific to DOTS over (D)TLS; please refer to the (D)TLS RFCs for
discussion of these security issues. DOTS agents MUST adhere to the
(D)TLS implementation recommendations and security considerations of
[RFC7525] except with respect to (D)TLS version. Since encryption of
DOTS using (D)TLS is virtually a green-field deployment DOTS agents
MUST implement only (D)TLS 1.2 or later.
Implementations compliant with this profile MUST implement all of the
following items:
o DOTS agents MUST support DTLS record replay detection (Section 3.3
of [RFC6347]) to protect against replay attacks.
o DOTS client can use (D)TLS session resumption without server-side
state [RFC5077] to resume session and convey the DOTS signal.
o Raw public keys [RFC7250] which reduce the size of the
ServerHello, and can be used by servers that cannot obtain
certificates (e.g., DOTS gateways on private networks).
Implementations compliant with this profile SHOULD implement all of
the following items to reduce the delay required to deliver a DOTS
signal:
o TLS False Start [RFC7918] which reduces round-trips by allowing
the TLS second flight of messages (ChangeCipherSpec) to also
contain the DOTS signal.
o Cached Information Extension [RFC7924] which avoids transmitting
the server's certificate and certificate chain if the client has
cached that information from a previous TLS handshake.
o TCP Fast Open [RFC7413] can reduce the number of round-trips to
convey DOTS signal.
7.1. MTU and Fragmentation Issues
To avoid DOTS signal message fragmentation and the consequently
decreased probability of message delivery, DOTS agents MUST ensure
that the DTLS record MUST fit within a single datagram. If the Path
MTU is not known to the DOTS server, an IP MTU of 1280 bytes SHOULD
be assumed. The length of the URL MUST NOT exceed 256 bytes. If UDP
is used to convey the DOTS signal messages then the DOTS client must
consider the amount of record expansion expected by the DTLS
processing when calculating the size of CoAP message that fits within
the path MTU. Path MTU MUST be greater than or equal to [CoAP
Reddy, et al. Expires May 16, 2018 [Page 44]
Internet-Draft DOTS Signal Channel November 2017
message size + DTLS overhead of 13 octets + authentication overhead
of the negotiated DTLS cipher suite + block padding (Section 4.1.1.1
of [RFC6347]]. If the request size exceeds the Path MTU then the
DOTS client MUST split the DOTS signal into separate messages, for
example the list of addresses in the 'target-ip' parameter could be
split into multiple lists and each list conveyed in a new PUT
request.
Implementation Note: DOTS choice of message size parameters works
well with IPv6 and with most of today's IPv4 paths. However, with
IPv4, it is harder to absolutely ensure that there is no IP
fragmentation. If IPv4 support on unusual networks is a
consideration and path MTU is unknown, implementations may want to
limit themselves to more conservative IPv4 datagram sizes such as 576
bytes, as per [RFC0791] IP packets up to 576 bytes should never need
to be fragmented, thus sending a maximum of 500 bytes of DOTS signal
over a UDP datagram will generally avoid IP fragmentation.
8. (D)TLS 1.3 considerations
TLS 1.3 [I-D.ietf-tls-tls13] provides critical latency improvements
for connection establishment over TLS 1.2. The DTLS 1.3 protocol
[I-D.rescorla-tls-dtls13] is based on the TLS 1.3 protocol and
provides equivalent security guarantees. (D)TLS 1.3 provides two
basic handshake modes of interest to DOTS signal channel:
o Absent packet loss, a full handshake in which the DOTS client is
able to send the DOTS signal message after one round trip and the
DOTS server immediately after receiving the first DOTS signal
message from the client.
o 0-RTT mode in which the DOTS client can authenticate itself and
send DOTS signal message on its first flight, thus reducing
handshake latency. 0-RTT only works if the DOTS client has
previously communicated with that DOTS server, which is very
likely with the DOTS signal channel. The DOTS client SHOULD
establish a (D)TLS session with the DOTS server during peacetime
and share a PSK. During DDOS attack, the DOTS client can use the
(D)TLS session to convey the DOTS signal message and if there is
no response from the server after multiple re-tries then the DOTS
client can resume the (D)TLS session in 0-RTT mode using PSK. A
simplified TLS 1.3 handshake with 0-RTT DOTS signal message
exchange is shown in Figure 23.
Reddy, et al. Expires May 16, 2018 [Page 45]
Internet-Draft DOTS Signal Channel November 2017
DOTS Client DOTS Server
ClientHello
(Finished)
(0-RTT DOTS signal message)
(end_of_early_data) -------->
ServerHello
{EncryptedExtensions}
{ServerConfiguration}
{Certificate}
{CertificateVerify}
{Finished}
<-------- [DOTS signal message]
{Finished} -------->
[DOTS signal message] <-------> [DOTS signal message]
Figure 23: TLS 1.3 handshake with 0-RTT
9. Mutual Authentication of DOTS Agents & Authorization of DOTS Clients
(D)TLS based on client certificate can be used for mutual
authentication between DOTS agents. If a DOTS gateway is involved,
DOTS clients and DOTS gateway MUST perform mutual authentication;
only authorized DOTS clients are allowed to send DOTS signals to a
DOTS gateway. DOTS gateway and DOTS server MUST perform mutual
authentication; DOTS server only allows DOTS signals from authorized
DOTS gateway, creating a two-link chain of transitive authentication
between the DOTS client and the DOTS server.
Reddy, et al. Expires May 16, 2018 [Page 46]
Internet-Draft DOTS Signal Channel November 2017
+-------------------------------------------------+
| example.com domain +---------+ |
| | AAA | |
| +---------------+ | Server | |
| | Application | +------+--+ |
| | server + ^
| | (DOTS client) |<-----------------+ | |
| +---------------+ | | | example.net domain
| V V |
| +-------------+ | +---------------+
| +--------------+ | | | | |
| | Guest +<-----x----->+ +<---------------->+ DOTS |
| | (DOTS client)| | DOTS | | | Server |
| +--------------+ | Gateway | | | |
| +----+--------+ | +---------------+
| ^ |
| | |
| +----------------+ | |
| | DDOS detector | | |
| | (DOTS client) +<--------------+ |
| +----------------+ |
| |
+-------------------------------------------------+
Figure 24: Example of Authentication and Authorization of DOTS Agents
In the example depicted in Figure 24, the DOTS gateway and DOTS
clients within the 'example.com' domain mutually authenticate with
each other. After the DOTS gateway validates the identity of a DOTS
client, it communicates with the AAA server in the 'example.com'
domain to determine if the DOTS client is authorized to request DDOS
mitigation. If the DOTS client is not authorized, a 4.01
(Unauthorized) is returned in the response to the DOTS client. In
this example, the DOTS gateway only allows the application server and
DDOS detector to request DDOS mitigation, but does not permit the
user of type 'guest' to request DDOS mitigation.
Also, DOTS gateway and DOTS server located in different domains MUST
perform mutual authentication (e.g., using certificates). A DOTS
server will only allow a DOTS gateway with a certificate for a
particular domain to request mitigation for that domain. In
reference to Figure 24, the DOTS server only allows the DOTS gateway
to request mitigation for 'example.com' domain and not for other
domains.
Reddy, et al. Expires May 16, 2018 [Page 47]
Internet-Draft DOTS Signal Channel November 2017
10. IANA Considerations
This specification registers a default port, new URI suffix in the
Well-Known URIs registry, new CoAP response code, new parameters for
DOTS signal channel and establishes registries for mappings to CBOR.
10.1. DOTS Signal Channel UDP and TCP Port Number
IANA has assigned the port number TBD to the DOTS signal channel
protocol, for both UDP and TCP.
10.2. Well-Known 'dots' URI
This memo registers the 'dots' well-known URI in the Well-Known URIs
registry as defined by [RFC5785].
URI suffix: dots
Change controller: IETF
Specification document(s): This RFC
Related information: None
10.3. CoAP Response Code
The following entry is added to the "CoAP Response Codes" sub-
registry:
+------+------------------------------+-----------+
| Code | Description | Reference |
+------+------------------------------+-----------+
| 3.00 | Alternate server | [RFCXXXX] |
+------+------------------------------+-----------+
Figure 25: CoAP Response Code
[Note to RFC Editor: Please replace XXXX with the RFC number of this
specification.]
10.4. DOTS signal channel CBOR Mappings Registry
A new registry will be requested from IANA, entitled "DOTS signal
channel CBOR Mappings Registry". The registry is to be created as
Expert Review Required.
Reddy, et al. Expires May 16, 2018 [Page 48]
Internet-Draft DOTS Signal Channel November 2017
10.4.1. Registration Template
Parameter name:
Parameter names (e.g., "target_ip") in the DOTS signal channel.
CBOR Key Value:
Key value for the parameter. The key value MUST be an integer in
the range of 1 to 65536. The key values in the range of 32768 to
65536 are assigned for Vendor-Specific parameters.
CBOR Major Type:
CBOR Major type and optional tag for the claim.
Change Controller:
For Standards Track RFCs, list the "IESG". For others, give the
name of the responsible party. Other details (e.g., postal
address, email address, home page URI) may also be included.
Specification Document(s):
Reference to the document or documents that specify the parameter,
preferably including URIs that can be used to retrieve copies of
the documents. An indication of the relevant sections may also be
included but is not required.
10.4.2. Initial Registry Contents
o Parameter Name: "mitigation-scope"
o CBOR Key Value: 1
o CBOR Major Type: 5
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: "scope"
o CBOR Key Value: 2
o CBOR Major Type: 5
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: "mitigation-id"
o CBOR Key Value: 3
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:target-ip
o CBOR Key Value: 4
o CBOR Major Type: 4
o Change Controller: IESG
Reddy, et al. Expires May 16, 2018 [Page 49]
Internet-Draft DOTS Signal Channel November 2017
o Specification Document(s): this document
o Parameter Name: target-port-range
o CBOR Key Value: 5
o CBOR Major Type: 4
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: "lower-port"
o CBOR Key Value: 6
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: "upper-port"
o CBOR Key Value: 7
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: target-protocol
o CBOR Key Value: 8
o CBOR Major Type: 4
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: "fqdn"
o CBOR Key Value: 9
o CBOR Major Type: 4
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: "uri"
o CBOR Key Value: 10
o CBOR Major Type: 4
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: alias-name
o CBOR Key Value: 11
o CBOR Major Type: 4
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: "lifetime"
o CBOR Key Value: 12
o CBOR Major Type: 0
o Change Controller: IESG
Reddy, et al. Expires May 16, 2018 [Page 50]
Internet-Draft DOTS Signal Channel November 2017
o Specification Document(s): this document
o Parameter Name: attack-status
o CBOR Key Value: 13
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: signal-config
o CBOR Key Value: 14
o CBOR Major Type: 5
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: heartbeat-interval
o CBOR Key Value: 15
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: max-retransmit
o CBOR Key Value: 16
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: ack-timeout
o CBOR Key Value: 17
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: ack-random-factor
o CBOR Key Value: 18
o CBOR Major Type: 7
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: MinValue
o CBOR Key Value: 19
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: MaxValue
o CBOR Key Value: 20
o CBOR Major Type: 0
o Change Controller: IESG
Reddy, et al. Expires May 16, 2018 [Page 51]
Internet-Draft DOTS Signal Channel November 2017
o Specification Document(s): this document
o Parameter Name: status
o CBOR Key Value: 21
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: bytes-dropped
o CBOR Key Value: 22
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: bps-dropped
o CBOR Key Value: 23
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: pkts-dropped
o CBOR Key Value: 24
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: pps-dropped
o CBOR Key Value: 25
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: session-id
o CBOR Key Value: 26
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: trigger-mitigation
o CBOR Key Value: 27
o CBOR Major Type: 7
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name: missing-hb-allowed
o CBOR Key Value: 28
o CBOR Major Type: 0
o Change Controller: IESG
Reddy, et al. Expires May 16, 2018 [Page 52]
Internet-Draft DOTS Signal Channel November 2017
o Specification Document(s): this document
o Parameter Name: CurrentValue
o CBOR Key Value: 29
o CBOR Major Type: 0
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:mitigation-start
o CBOR Key Value: 30
o CBOR Major Type: 7
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:target-prefix
o CBOR Key Value: 31
o CBOR Major Type: 4
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:client-identifier
o CBOR Key Value: 32
o CBOR Major Type: 2
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:alt-server
o CBOR Key Value: 33
o CBOR Major Type: 2
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:alt-server-record
o CBOR Key Value: 34
o CBOR Major Type: 4
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:addr
o CBOR Key Value: 35
o CBOR Major Type: 2
o Change Controller: IESG
o Specification Document(s): this document
o Parameter Name:ttl
o CBOR Key Value: 36
o CBOR Major Type: 0
o Change Controller: IESG
Reddy, et al. Expires May 16, 2018 [Page 53]
Internet-Draft DOTS Signal Channel November 2017
o Specification Document(s): this document
11. Implementation Status
[Note to RFC Editor: Please remove this section and reference to
[RFC7942] prior to publication.]
This section records the status of known implementations of the
protocol defined by this specification at the time of posting of this
Internet-Draft, and is based on a proposal described in [RFC7942].
The description of implementations in this section is intended to
assist the IETF in its decision processes in progressing drafts to
RFCs. Please note that the listing of any individual implementation
here does not imply endorsement by the IETF. Furthermore, no effort
has been spent to verify the information presented here that was
supplied by IETF contributors. This is not intended as, and must not
be construed to be, a catalog of available implementations or their
features. Readers are advised to note that other implementations may
exist.
According to [RFC7942], "this will allow reviewers and working groups
to assign due consideration to documents that have the benefit of
running code, which may serve as evidence of valuable experimentation
and feedback that have made the implemented protocols more mature.
It is up to the individual working groups to use this information as
they see fit".
11.1. nttdots
Organization: NTT Communication is developing a DOTS client and
DOTS server software based on DOTS signal channel specified in
this draft. It will be open-sourced.
Description: Early implementation of DOTS protocol. It is aimed to
implement a full DOTS protocol spec in accordance with maturing of
DOTS protocol itself.
Implementation: https://github.com/nttdots/go-dots
Level of maturity: It is a early implementation of DOTS protocol.
Messaging between DOTS clients and DOTS servers has been tested.
Level of maturity will increase in accordance with maturing of
DOTS protocol itself.
Coverage: Capability of DOTS client: sending DOTS messages to the
DOTS server in CoAP over DTLS as dots-signal. Capability of DOTS
server: receiving dots-signal, validating received dots-signal,
starting mitigation by handing over the dots-signal to DDOS
mitigator.
Licensing: It will be open-sourced with BSD 3-clause license.
Reddy, et al. Expires May 16, 2018 [Page 54]
Internet-Draft DOTS Signal Channel November 2017
Implementation experience: It is implemented in Go-lang. Core
specification of signaling is mature to be implemented, however,
finding good libraries(like DTLS, CoAP) is rather difficult.
Contact: Kaname Nishizuka <kaname@nttv6.jp>
12. Security Considerations
Authenticated encryption MUST be used for data confidentiality and
message integrity. (D)TLS based on client certificate MUST be used
for mutual authentication. The interaction between the DOTS agents
requires Datagram Transport Layer Security (DTLS) and Transport Layer
Security (TLS) with a cipher suite offering confidentiality
protection and the guidance given in [RFC7525] MUST be followed to
avoid attacks on (D)TLS.
A single DOTS signal channel between DOTS agents can be used to
exchange multiple DOTS signal messages. To reduce DOTS client and
DOTS server workload, DOTS client SHOULD re-use the (D)TLS session.
If TCP is used between DOTS agents, an attacker may be able to inject
RST packets, bogus application segments, etc., regardless of whether
TLS authentication is used. Because the application data is TLS
protected, this will not result in the application receiving bogus
data, but it will constitute a DoS on the connection. This attack
can be countered by using TCP-AO [RFC5925]. If TCP-AO is used, then
any bogus packets injected by an attacker will be rejected by the
TCP-AO integrity check and therefore will never reach the TLS layer.
In order to prevent leaking internal information outside a client-
domain, DOTS gateways located in the client-domain SHOULD NOT reveal
the identity of internal DOTS clients (client-identifier) unless
explicitly configured to do so.
Special care should be taken in order to ensure that the activation
of the proposed mechanism won't have an impact on the stability of
the network (including connectivity and services delivered over that
network).
Involved functional elements in the cooperation system must establish
exchange instructions and notification over a secure and
authenticated channel. Adequate filters can be enforced to avoid
that nodes outside a trusted domain can inject request such as
deleting filtering rules. Nevertheless, attacks can be initiated
from within the trusted domain if an entity has been corrupted.
Adequate means to monitor trusted nodes should also be enabled.
Reddy, et al. Expires May 16, 2018 [Page 55]
Internet-Draft DOTS Signal Channel November 2017
13. Contributors
The following individuals have contributed to this document:
Mike Geller Cisco Systems, Inc. 3250 Florida 33309 USA Email:
mgeller@cisco.com
Robert Moskowitz HTT Consulting Oak Park, MI 42837 United States
Email: rgm@htt-consult.com
Dan Wing Email: dwing-ietf@fuggles.com
14. Acknowledgements
Thanks to Christian Jacquenet, Roland Dobbins, Roman D. Danyliw,
Michael Richardson, Ehud Doron, Kaname Nishizuka, Dave Dolson, Liang
Xia, Jon Shallow, and Gilbert Clark for the discussion and comments.
15. References
15.1. Normative References
[I-D.ietf-core-coap-tcp-tls]
Bormann, C., Lemay, S., Tschofenig, H., Hartke, K.,
Silverajan, B., and B. Raymor, "CoAP (Constrained
Application Protocol) over TCP, TLS, and WebSockets",
draft-ietf-core-coap-tcp-tls-10 (work in progress),
October 2017.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246,
DOI 10.17487/RFC5246, August 2008,
<https://www.rfc-editor.org/info/rfc5246>.
[RFC5785] Nottingham, M. and E. Hammer-Lahav, "Defining Well-Known
Uniform Resource Identifiers (URIs)", RFC 5785,
DOI 10.17487/RFC5785, April 2010,
<https://www.rfc-editor.org/info/rfc5785>.
[RFC5925] Touch, J., Mankin, A., and R. Bonica, "The TCP
Authentication Option", RFC 5925, DOI 10.17487/RFC5925,
June 2010, <https://www.rfc-editor.org/info/rfc5925>.
Reddy, et al. Expires May 16, 2018 [Page 56]
Internet-Draft DOTS Signal Channel November 2017
[RFC6234] Eastlake 3rd, D. and T. Hansen, "US Secure Hash Algorithms
(SHA and SHA-based HMAC and HKDF)", RFC 6234,
DOI 10.17487/RFC6234, May 2011,
<https://www.rfc-editor.org/info/rfc6234>.
[RFC6347] Rescorla, E. and N. Modadugu, "Datagram Transport Layer
Security Version 1.2", RFC 6347, DOI 10.17487/RFC6347,
January 2012, <https://www.rfc-editor.org/info/rfc6347>.
[RFC7250] Wouters, P., Ed., Tschofenig, H., Ed., Gilmore, J.,
Weiler, S., and T. Kivinen, "Using Raw Public Keys in
Transport Layer Security (TLS) and Datagram Transport
Layer Security (DTLS)", RFC 7250, DOI 10.17487/RFC7250,
June 2014, <https://www.rfc-editor.org/info/rfc7250>.
[RFC7252] Shelby, Z., Hartke, K., and C. Bormann, "The Constrained
Application Protocol (CoAP)", RFC 7252,
DOI 10.17487/RFC7252, June 2014,
<https://www.rfc-editor.org/info/rfc7252>.
[RFC7525] Sheffer, Y., Holz, R., and P. Saint-Andre,
"Recommendations for Secure Use of Transport Layer
Security (TLS) and Datagram Transport Layer Security
(DTLS)", BCP 195, RFC 7525, DOI 10.17487/RFC7525, May
2015, <https://www.rfc-editor.org/info/rfc7525>.
[RFC7641] Hartke, K., "Observing Resources in the Constrained
Application Protocol (CoAP)", RFC 7641,
DOI 10.17487/RFC7641, September 2015,
<https://www.rfc-editor.org/info/rfc7641>.
15.2. Informative References
[I-D.ietf-core-comi]
Veillette, M., Stok, P., Pelov, A., and A. Bierman, "CoAP
Management Interface", draft-ietf-core-comi-01 (work in
progress), July 2017.
[I-D.ietf-core-yang-cbor]
Veillette, M., Pelov, A., Somaraju, A., Turner, R., and A.
Minaburo, "CBOR Encoding of Data Modeled with YANG",
draft-ietf-core-yang-cbor-05 (work in progress), August
2017.
Reddy, et al. Expires May 16, 2018 [Page 57]
Internet-Draft DOTS Signal Channel November 2017
[I-D.ietf-dots-architecture]
Mortensen, A., Andreasen, F., Reddy, T.,
christopher_gray3@cable.comcast.com, c., Compton, R., and
N. Teague, "Distributed-Denial-of-Service Open Threat
Signaling (DOTS) Architecture", draft-ietf-dots-
architecture-05 (work in progress), October 2017.
[I-D.ietf-dots-data-channel]
Reddy, T., Boucadair, M., Nishizuka, K., Xia, L., Patil,
P., Mortensen, A., and N. Teague, "Distributed Denial-of-
Service Open Threat Signaling (DOTS) Data Channel", draft-
ietf-dots-data-channel-06 (work in progress), October
2017.
[I-D.ietf-dots-requirements]
Mortensen, A., Moskowitz, R., and T. Reddy, "Distributed
Denial of Service (DDoS) Open Threat Signaling
Requirements", draft-ietf-dots-requirements-07 (work in
progress), October 2017.
[I-D.ietf-dots-use-cases]
Dobbins, R., Migault, D., Fouant, S., Moskowitz, R.,
Teague, N., Xia, L., and K. Nishizuka, "Use cases for DDoS
Open Threat Signaling", draft-ietf-dots-use-cases-09 (work
in progress), November 2017.
[I-D.ietf-tls-tls13]
Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", draft-ietf-tls-tls13-21 (work in progress),
July 2017.
[I-D.rescorla-tls-dtls13]
Rescorla, E., Tschofenig, H., and N. Modadugu, "The
Datagram Transport Layer Security (DTLS) Protocol Version
1.3", draft-rescorla-tls-dtls13-01 (work in progress),
March 2017.
[proto_numbers]
"IANA, "Protocol Numbers"", 2011,
<http://www.iana.org/assignments/protocol-numbers>.
[RFC0791] Postel, J., "Internet Protocol", STD 5, RFC 791,
DOI 10.17487/RFC0791, September 1981,
<https://www.rfc-editor.org/info/rfc791>.
Reddy, et al. Expires May 16, 2018 [Page 58]
Internet-Draft DOTS Signal Channel November 2017
[RFC4340] Kohler, E., Handley, M., and S. Floyd, "Datagram
Congestion Control Protocol (DCCP)", RFC 4340,
DOI 10.17487/RFC4340, March 2006,
<https://www.rfc-editor.org/info/rfc4340>.
[RFC4632] Fuller, V. and T. Li, "Classless Inter-domain Routing
(CIDR): The Internet Address Assignment and Aggregation
Plan", BCP 122, RFC 4632, DOI 10.17487/RFC4632, August
2006, <https://www.rfc-editor.org/info/rfc4632>.
[RFC4732] Handley, M., Ed., Rescorla, E., Ed., and IAB, "Internet
Denial-of-Service Considerations", RFC 4732,
DOI 10.17487/RFC4732, December 2006,
<https://www.rfc-editor.org/info/rfc4732>.
[RFC4787] Audet, F., Ed. and C. Jennings, "Network Address
Translation (NAT) Behavioral Requirements for Unicast
UDP", BCP 127, RFC 4787, DOI 10.17487/RFC4787, January
2007, <https://www.rfc-editor.org/info/rfc4787>.
[RFC4960] Stewart, R., Ed., "Stream Control Transmission Protocol",
RFC 4960, DOI 10.17487/RFC4960, September 2007,
<https://www.rfc-editor.org/info/rfc4960>.
[RFC4987] Eddy, W., "TCP SYN Flooding Attacks and Common
Mitigations", RFC 4987, DOI 10.17487/RFC4987, August 2007,
<https://www.rfc-editor.org/info/rfc4987>.
[RFC5077] Salowey, J., Zhou, H., Eronen, P., and H. Tschofenig,
"Transport Layer Security (TLS) Session Resumption without
Server-Side State", RFC 5077, DOI 10.17487/RFC5077,
January 2008, <https://www.rfc-editor.org/info/rfc5077>.
[RFC6020] Bjorklund, M., Ed., "YANG - A Data Modeling Language for
the Network Configuration Protocol (NETCONF)", RFC 6020,
DOI 10.17487/RFC6020, October 2010,
<https://www.rfc-editor.org/info/rfc6020>.
[RFC6555] Wing, D. and A. Yourtchenko, "Happy Eyeballs: Success with
Dual-Stack Hosts", RFC 6555, DOI 10.17487/RFC6555, April
2012, <https://www.rfc-editor.org/info/rfc6555>.
[RFC6724] Thaler, D., Ed., Draves, R., Matsumoto, A., and T. Chown,
"Default Address Selection for Internet Protocol Version 6
(IPv6)", RFC 6724, DOI 10.17487/RFC6724, September 2012,
<https://www.rfc-editor.org/info/rfc6724>.
Reddy, et al. Expires May 16, 2018 [Page 59]
Internet-Draft DOTS Signal Channel November 2017
[RFC7030] Pritikin, M., Ed., Yee, P., Ed., and D. Harkins, Ed.,
"Enrollment over Secure Transport", RFC 7030,
DOI 10.17487/RFC7030, October 2013,
<https://www.rfc-editor.org/info/rfc7030>.
[RFC7049] Bormann, C. and P. Hoffman, "Concise Binary Object
Representation (CBOR)", RFC 7049, DOI 10.17487/RFC7049,
October 2013, <https://www.rfc-editor.org/info/rfc7049>.
[RFC7413] Cheng, Y., Chu, J., Radhakrishnan, S., and A. Jain, "TCP
Fast Open", RFC 7413, DOI 10.17487/RFC7413, December 2014,
<https://www.rfc-editor.org/info/rfc7413>.
[RFC7589] Badra, M., Luchuk, A., and J. Schoenwaelder, "Using the
NETCONF Protocol over Transport Layer Security (TLS) with
Mutual X.509 Authentication", RFC 7589,
DOI 10.17487/RFC7589, June 2015,
<https://www.rfc-editor.org/info/rfc7589>.
[RFC7918] Langley, A., Modadugu, N., and B. Moeller, "Transport
Layer Security (TLS) False Start", RFC 7918,
DOI 10.17487/RFC7918, August 2016,
<https://www.rfc-editor.org/info/rfc7918>.
[RFC7924] Santesson, S. and H. Tschofenig, "Transport Layer Security
(TLS) Cached Information Extension", RFC 7924,
DOI 10.17487/RFC7924, July 2016,
<https://www.rfc-editor.org/info/rfc7924>.
[RFC7942] Sheffer, Y. and A. Farrel, "Improving Awareness of Running
Code: The Implementation Status Section", BCP 205,
RFC 7942, DOI 10.17487/RFC7942, July 2016,
<https://www.rfc-editor.org/info/rfc7942>.
[RFC8085] Eggert, L., Fairhurst, G., and G. Shepherd, "UDP Usage
Guidelines", BCP 145, RFC 8085, DOI 10.17487/RFC8085,
March 2017, <https://www.rfc-editor.org/info/rfc8085>.
Authors' Addresses
Tirumaleswar Reddy
McAfee, Inc.
Embassy Golf Link Business Park
Bangalore, Karnataka 560071
India
Email: kondtir@gmail.com
Reddy, et al. Expires May 16, 2018 [Page 60]
Internet-Draft DOTS Signal Channel November 2017
Mohamed Boucadair
Orange
Rennes 35000
France
Email: mohamed.boucadair@orange.com
Prashanth Patil
Cisco Systems, Inc.
Email: praspati@cisco.com
Andrew Mortensen
Arbor Networks, Inc.
2727 S. State St
Ann Arbor, MI 48104
United States
Email: amortensen@arbor.net
Nik Teague
Verisign, Inc.
United States
Email: nteague@verisign.com
Reddy, et al. Expires May 16, 2018 [Page 61]