DMM Working Group                                          S. Matsushima
Internet-Draft                                                  SoftBank
Intended status: Standards Track                             C. Filsfils
Expires: September 12, 2019                                     M. Kohno
                                                            P. Camarillo
                                                     Cisco Systems, Inc.
                                                                D. Voyer
                                                             Bell Canada
                                                              C. Perkins
                                                               Futurewei
                                                          March 11, 2019


               Segment Routing IPv6 for Mobile User Plane
                  draft-ietf-dmm-srv6-mobile-uplane-04

Abstract

   This document shows the applicability of SRv6 (Segment Routing IPv6)
   to the user-plane of mobile networks.  The network programming nature
   of SRv6 accomplish mobile user-plane functions in a simple manner.
   The statelessness of SRv6 and its ability to control both service
   layer path and underlying transport can be beneficial to the mobile
   user-plane, providing flexibility and SLA control for various
   applications.  This document describes the SRv6 mobile user plane
   behavior and defines the SID functions for that.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 12, 2019.








Matsushima, et al.     Expires September 12, 2019               [Page 1]


Internet-Draft             SRv6-mobile-uplane                 March 2019


Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Conventions and Terminology . . . . . . . . . . . . . . . . .   3
     2.1.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   3
     2.2.  Conventions . . . . . . . . . . . . . . . . . . . . . . .   4
     2.3.  Predefined SRv6 Functions . . . . . . . . . . . . . . . .   4
   3.  Motivation  . . . . . . . . . . . . . . . . . . . . . . . . .   5
   4.  A 3GPP Reference Architecture . . . . . . . . . . . . . . . .   6
   5.  User-plane behaviors  . . . . . . . . . . . . . . . . . . . .   7
     5.1.  Traditional mode  . . . . . . . . . . . . . . . . . . . .   7
       5.1.1.  Packet flow - Uplink  . . . . . . . . . . . . . . . .   8
       5.1.2.  Packet flow - Downlink  . . . . . . . . . . . . . . .   8
       5.1.3.  IPv6 user-traffic . . . . . . . . . . . . . . . . . .   9
     5.2.  Enhanced Mode . . . . . . . . . . . . . . . . . . . . . .   9
       5.2.1.  Packet flow - Uplink  . . . . . . . . . . . . . . . .  10
       5.2.2.  Packet flow - Downlink  . . . . . . . . . . . . . . .  11
       5.2.3.  IPv6 user-traffic . . . . . . . . . . . . . . . . . .  11
     5.3.  Enhanced mode with unchanged gNB GTP behavior . . . . . .  11
       5.3.1.  Interworking with IPv6 GTP  . . . . . . . . . . . . .  12
       5.3.2.  Interworking with IPv4 GTP  . . . . . . . . . . . . .  15
       5.3.3.  Extensions to the interworking mechanisms . . . . . .  17
   6.  SRv6 SID Mobility Functions . . . . . . . . . . . . . . . . .  18
     6.1.  Args.Mob.Session  . . . . . . . . . . . . . . . . . . . .  18
     6.2.  End.MAP . . . . . . . . . . . . . . . . . . . . . . . . .  18
     6.3.  End.M.GTP6.D  . . . . . . . . . . . . . . . . . . . . . .  19
     6.4.  End.M.GTP6.E  . . . . . . . . . . . . . . . . . . . . . .  19
     6.5.  End.M.GTP4.E  . . . . . . . . . . . . . . . . . . . . . .  20
     6.6.  T.M.Tmap  . . . . . . . . . . . . . . . . . . . . . . . .  20
     6.7.  End.Limit: Rate Limiting function . . . . . . . . . . . .  21
   7.  SRv6 supported 3GPP PDU session types . . . . . . . . . . . .  22
   8.  Network Slicing Considerations  . . . . . . . . . . . . . . .  22
   9.  Control Plane Considerations  . . . . . . . . . . . . . . . .  22



Matsushima, et al.     Expires September 12, 2019               [Page 2]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   10. Security Considerations . . . . . . . . . . . . . . . . . . .  23
   11. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  23
   12. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  23
   13. Contributors  . . . . . . . . . . . . . . . . . . . . . . . .  23
   14. References  . . . . . . . . . . . . . . . . . . . . . . . . .  24
     14.1.  Normative References . . . . . . . . . . . . . . . . . .  24
     14.2.  Informative References . . . . . . . . . . . . . . . . .  25
   Appendix A.  Implementations  . . . . . . . . . . . . . . . . . .  26
   Appendix B.  Changes from revision 02 to revision 03  . . . . . .  26
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  27

1.  Introduction

   In mobile networks, mobility management systems provide connectivity
   while mobile nodes move.  While the control-plane of the system
   signals movements of a mobile node, the user-plane establishes a
   tunnel between the mobile node and its anchor node over IP-based
   backhaul and core networks.

   This document shows the applicability of SRv6 (Segment Routing IPv6)
   to those mobile networks.  SRv6 provides source routing to networks
   so that operators can explicitly indicate a route for the packets to
   and from the mobile node.  SRv6 endpoint nodes serve as the anchors
   of mobile user-plane.

2.  Conventions and Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

2.1.  Terminology

   o  AMBR: Aggregate Maximum Bit Rate
   o  APN: Access Point Name (commonly used to identify a network or
      class of service)
   o  BSID: SR Binding SID [RFC8402]
   o  CNF: Cloud-native Network Function
   o  gNB: gNodeB
   o  NH: The IPv6 next-header field.
   o  NFV: Network Function Virtualization
   o  PDU: Packet Data Unit
   o  Session: TBD...
   o  SID: A Segment Identifier which represents a specific segment in a
      segment routing domain.
   o  SRH: The Segment Routing Header.
      [I-D.ietf-6man-segment-routing-header]
   o  TEID: Tunnel Endpoint Identifier



Matsushima, et al.     Expires September 12, 2019               [Page 3]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   o  UE: User Equipment
   o  UPF: User Plane Function
   o  VNF: Virtual Network Function

2.2.  Conventions

   o  NH=SRH means that NH is 43 with routing type 4.
   o  Multiple SRHs may be present inside each packet, but they must
      follow each other.  The next-header field of each SRH, except the
      last one, must be NH-SRH (43 type 4).
   o  For simplicity, no other extension headers are shown except the
      SRH.
   o  The SID type used in this document is IPv6 address (also called
      SRv6 Segment or SRv6 SID).
   o  gNB::1 is an IPv6 address (SID) assigned to the gNB.
   o  U1::1 is an IPv6 address (SID) assigned to UPF1.
   o  U2::1 is an IPv6 address (SID) assigned to UPF2.
   o  U2:: is some other IPv6 address (SID) assigned to UPF2.
   o  A SID list is represented as <S1, S2, S3> where S1 is the first
      SID to visit, S2 is the second SID to visit and S3 is the last SID
      to visit along the SR path.
   o  (SA,DA) (S3, S2, S1; SL) represents an IPv6 packet with:

      *  IPv6 header with source and destination addresses SA and DA
         respectively, and next-header SRH, with SID list <S1, S2, S3>
         with SegmentsLeft = SL
      *  The payload of the packet is not represented.
   o  Note the difference between the <> and () symbols: <S1, S2, S3>
      represents a SID list where S1 is the first SID and S3 is the last
      SID.  (S3, S2, S1; SL) represents the same SID list but encoded in
      the SRH format where the rightmost SID in the SRH is the first SID
      and the leftmost SID in the SRH is the last SID.  When referring
      to an SR policy in a high-level use-case, it is simpler to use the
      <S1, S2, S3> notation.  When referring to an illustration of the
      detailed behavior, the (S3, S2, S1; SL) notation is more
      convenient.
   o  SRH[SL] represents the SID pointed by the SL field in the first
      SRH.  In our example, SRH[2] represents S1, SRH[1] represents S2
      and SRH[0] represents S3.
   o  SRH[SL] can be different from the DA of the IPv6 header.

2.3.  Predefined SRv6 Functions

   The following functions are defined in
   [I-D.filsfils-spring-srv6-network-programming].

   o  End.DT4 means to decapsulate and forward using a specific IPv4
      table lookup.



Matsushima, et al.     Expires September 12, 2019               [Page 4]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   o  End.DT6 means to decapsulate and forward using a specific IPv6
      table lookup.
   o  End.DX4 means to decapsulate the packet and forward through a
      particular outgoing interface -or set of OIFs- configured with the
      SID.
   o  End.DX6 means to decapsulate and forward through a particular
      outgoing interface -or set of OIFs- configured with the SID.
   o  End.DX2 means to decapsulate the L2 frame and forward through a
      particular outgoing interface -or set of OIFs- configured with the
      SID.
   o  End.T means to forward using a specific IPv6 table lookup.
   o  End.X means to forward through a link configured with the SID.
   o  T.Encaps.Red means encapsulation without pushing SRH (resulting in
      "Reduced" packet size).
   o  PSP means Penultimate Segment Pop.  The packet is subsequently
      forwarded without the popped SRH.

   New SRv6 functions are defined in Section 6 to support the needs of
   the mobile user plane.

3.  Motivation

   Mobility networks are becoming more challenging to operate.  On one
   hand, traffic is constantly growing, and latency requirements are
   more strict; on the other-hand, there are new use-cases like NFV that
   are also challenging network management.

   The current architecture of mobile networks does not take into
   account the underlying transport.  The user-plane is rigidly
   fragmented into radio access, core and service networks, connected by
   tunneling according to user-plane roles such as access and anchor
   nodes.  These factors have made it difficult for the operator to
   optimize and operate the data-path.

   In the meantime, applications have shifted to use IPv6, and network
   operators have started adopting IPv6 as their IP transport.  SRv6,
   the IPv6 dataplane instantiation of Segment Routing [RFC8402],
   integrates both the application data-path and the underlying
   transport layer into a single protocol, allowing operators to
   optimize the network in a simplified manner and removing forwarding
   state from the network.  It is also suitable for virtualized
   environments, VNF/CNF to VNF/CNF networking.

   SRv6 specifies network-programming (see
   [I-D.filsfils-spring-srv6-network-programming]).  Applied to
   mobility, SRv6 can provide the user-plane functions needed for
   mobility management.  SRv6 takes advantage of underlying transport
   awareness and flexibility to improve mobility user-plane functions.



Matsushima, et al.     Expires September 12, 2019               [Page 5]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   The use-cases for SRv6 mobility are discussed in
   [I-D.camarilloelmalky-springdmm-srv6-mob-usecases].

4.  A 3GPP Reference Architecture

   This section presents a reference architecture and possible
   deployment scenarios.

   Figure 1 shows a reference diagram from the 5G packet core
   architecture [TS.23501].

   The user plane described in this document does not depend on any
   specific architecture.  The 5G packet core architecture as shown is
   based on the latest 3GPP standards at the time of writing this draft.
   Other architectures can be seen in [I-D.gundavelli-dmm-mfa] and
   [WHITEPAPER-5G-UP].

                                  +-----+
                                  | AMF |
                                  +-----+
                                 /    | [N11]
                          [N2]  /  +-----+
                        +------/   | SMF |
                       /           +-----+
                      /              / \
                     /              /   \  [N4]
                    /              /     \                    ________
                   /              /       \                  /        \
   +--+      +-----+ [N3] +------+  [N9]  +------+  [N6]    /          \
   |UE|------| gNB |------| UPF1 |--------| UPF2 |--------- \    DN    /
   +--+      +-----+      +------+        +------+           \________/

                 Figure 1: 3GPP 5G Reference Architecture

   o  gNB: gNodeB
   o  UPF1: UPF with Interfaces N3 and N9
   o  UPF2: UPF with Interfaces N9 and N6
   o  SMF: Session Management Function
   o  AMF: Access and Mobility Management Function
   o  DN: Data Network e.g. operator services, Internet access

   This reference diagram does not depict a UPF that is only connected
   to N9 interfaces, although the description in this document also work
   for such UPFs.

   Each session from an UE gets assigned to a UPF.  Sometimes multiple
   UPFs may be used, providing richer service functions.  A UE gets its
   IP address from the DHCP block of its UPF.  The UPF advertises that



Matsushima, et al.     Expires September 12, 2019               [Page 6]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   IP address block toward the Internet, ensuring that return traffic is
   routed to the right UPF.

5.  User-plane behaviors

   This section describes some mobile user-plane behaviors using SRv6.

   In order to simplify the adoption of SRv6, we present two different
   "modes" that vary with respect to the use of SRv6.  The first one is
   the "Traditional mode", which inherits the current 3GPP mobile user-
   plane.  In this mode there is no change to mobility networks
   architecture, except that GTP-U [TS.29281] is replaced by SRv6.

   The second mode is the "Enhanced mode".  In this mode the SR policy
   contains SIDs for Traffic Engineering and VNFs, which results in
   effective end-to-end network slices.

   In both, the Traditional and the Enhanced modes, we assume that the
   gNB as well as the UPFs are SR-aware (N3, N9 and -potentially- N6
   interfaces are SRv6).

   We introduce two mechanisms for interworking with legacy access
   networks (N3 interface is unmodified).  In these document we
   introduce them applied to the Enhanced mode, although they could be
   used in combination with the Traditional mode as well.

   One of these mechanisms is designed to interwork with legacy gNBs
   using GTP/IPv4.  The second method is designed to interwork with
   legacy gNBs using GTP/IPv6.

   This document uses SRv6 functions defined in
   [I-D.filsfils-spring-srv6-network-programming] as well as new SRv6
   functions designed for the mobile user plane.  The new SRv6 functions
   are detailed in Section 6.

5.1.  Traditional mode

   In the traditional mode, the existing mobile UPFs remain unchanged
   except for the use of SRv6 as the data plane instead of GTP-U.  There
   is no impact to the rest of mobile system.

   In existing 3GPP mobile networks, an UE session is mapped 1-for-1
   with a specific GTP tunnel (TEID).  This 1-for-1 mapping is mirrored
   here to replace GTP encapsulation with the SRv6 encapsulation, while
   not changing anything else.  There will be a unique SRv6 SID
   associated with each UE session.





Matsushima, et al.     Expires September 12, 2019               [Page 7]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   The traditional mode minimizes the changes required to the mobile
   system; it is a good starting point for forming a common basis.

   Our example topology is shown in Figure 2.  In traditional mode the
   gNB and the UPFs are SR-aware.  In the descriptions of the uplink and
   downlink packet flow, A is an IPv6 address of the UE, and Z is an
   IPv6 address reachable within the Data Network DN.  A new SRv6
   function End.MAP, defined in Section 6.2, is used.

                                                              ________
                     SRv6           SRv6                     /        \
   +--+      +-----+ [N3] +------+  [N9]  +------+  [N6]    /          \
   |UE|------| gNB |------| UPF1 |--------| UPF2 |--------- \    DN    /
   +--+      +-----+      +------+        +------+           \________/
            SRv6 node     SRv6 node       SRv6 node

               Figure 2: Traditional mode - example topology

5.1.1.  Packet flow - Uplink

   The uplink packet flow is as follows:

         UE_out  : (A,Z)
         gNB_out : (gNB, U1::1) (A,Z)     -> T.Encaps.Red <U1::1>
         UPF1_out: (gNB, U2::1) (A,Z)     -> End.MAP
         UPF2_out: (A,Z)                  -> End.DT4 or End.DT6

   When the UE packet arrives at the gNB, the gNB performs a
   T.Encaps.Red operation.  Since there is only one SID, there is no
   need to push an SRH. gNB only adds an outer IPv6 header with IPv6 DA
   U1::1.  U1::1 represents an anchoring SID specific for that session
   at UPF1. gNB obtains the SID U1::1 from the existing control plane
   (N2 interface).

   When the packet arrives at UPF1, the SID U1::1 identifies a local
   End.MAP function.  End.MAP replaces U1::1 by U2::1, that belongs to
   the next UPF (U2).

   When the packet arrives at UPF2, the SID U2::1 corresponds to an
   End.DT function.  UPF2 decapsulates the packet, performs a lookup in
   a specific table associated with that mobile network and forwards the
   packet toward the data network (DN).

5.1.2.  Packet flow - Downlink

   The downlink packet flow is as follows:





Matsushima, et al.     Expires September 12, 2019               [Page 8]


Internet-Draft             SRv6-mobile-uplane                 March 2019


         UPF2_in : (Z,A)
         UPF2_out: (U2::, U1::1) (Z,A)    -> T.Encaps.Red <U1::1>
         UPF1_out: (U2::, gNB::1) (Z,A)   -> End.MAP
         gNB_out : (Z,A)                  -> End.DX4 or End.DX6

   When the packet arrives at the UPF2, the UPF2 maps that flow into a
   UE session.  This UE session is associated with the segment endpoint
   <U1::1>.  UPF2 performs a T.Encaps.Red operation, encapsulating the
   packet into a new IPv6 header with no SRH since there is only one
   SID.

   Upon packet arrival on UPF1, the SID U1::1 is a local End.MAP
   function.  This function maps the SID to the next anchoring point and
   replaces U1::1 by gNB::1, that belongs to the next hop.

   Upon packet arrival on gNB, the SID gNB::1 corresponds to an End.DX4
   or End.DX6 function.  The gNB decapsulates the packet, removing the
   IPv6 header and all its extensions headers, and forwards the traffic
   toward the UE.

5.1.3.  IPv6 user-traffic

   For IPv6 user-traffic it is RECOMMENDED to perform encapsulation.
   However based on local policy, a service provider MAY choose to do
   SRH insertion [I-D.voyer-6man-extension-header-insertion] . The main
   benefit is a lower overhead (40B less).  In such case, the functions
   used are T.Insert.Red at gNB, End.MAP at UPF1 and End.T at UPF2 on
   Uplink, T.Insert.Red at UPF2, End.MAP at UPF1 and End.X at gNB on
   Downlink.

5.2.  Enhanced Mode

   Enhanced mode improves scalability, traffic steering and service
   programming [I-D.xuclad-spring-sr-service-programming], thanks to the
   use of multiple SIDs, instead of a single SID as done in the
   Traditional mode.

   The main difference is that the SR policy MAY include SIDs for
   traffic engineering and service programming in addition to the UPFs
   SIDs.

   The gNB control-plane (N2 interface) is unchanged, specifically a
   single IPv6 address is given to the gNB.

   o  The gNB MAY resolve the IP address into a SID list using a
      mechanism like PCEP, DNS-lookup, small augment for LISP control-
      plane, etc.




Matsushima, et al.     Expires September 12, 2019               [Page 9]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   Note that the SIDs MAY use the arguments Args.Mob.Session if required
   by the UPFs.

   Figure 3 shows an Enhanced mode topology.  In the Enhanced mode, the
   gNB and the UPF are SR-aware.  The Figure shows two service segments,
   S1 and C1.  S1 represents a VNF in the network, and C1 represents a
   constraint path on a router requiring Traffic Engineering.  S1 and C1
   belong to the underlay and don't have an N4 interface, so they are
   not considered UPFs.

                                    +----+  SRv6               _______
                    SRv6          --| C1 |--[N3]              /       \
   +--+    +-----+  [N3]         /  +----+  \  +------+ [N6] /         \
   |UE|----| gNB |--       SRv6 /    SRv6    --| UPF2 |------\   DN    /
   +--+    +-----+  \      [N3]/      TE       +------+       \_______/
          SRv6 node  \ +----+ /               SRv6 node
                      -| S1 |-
                       +----+
                      SRv6 node
                        CNF

                Figure 3: Enhanced mode - Example topology

5.2.1.  Packet flow - Uplink

   The uplink packet flow is as follows:

   UE_out  : (A,Z)
   gNB_out : (gNB, S1)(U2::1, C1; SL=2)(A,Z)-> T.Encaps.Red<S1,C1,U2::1>
   S1_out  : (gNB, C1)(U2::1, C1; SL=1 (A,Z)
   C1_out  : (gNB, U2::1)(A,Z)              -> PSP
   UPF2_out: (A,Z)                          -> End.DT4 or End.DT6

   UE sends its packet (A,Z) on a specific bearer to its gNB.  gNB's
   control plane associates that session from the UE(A) with the IPv6
   address B and GTP TEID T.  gNB's control plane does a lookup on B to
   find the related SID list <S1, C1, U2::1>.

   When gNB transmits the packet, it contains all the segments of the SR
   policy.  The SR policy can include segments for traffic engineering
   (C1) and for service programming (S1).

   Nodes S1 and C1 perform their related Endpoint functionality and
   forward the packet.

   When the packet arrives at UPF2, the active segment (U2::1) is an
   End.DT4/6 which performs the decapsulation (removing the IPv6 header
   with all its extension headers) and forwards toward the data network.



Matsushima, et al.     Expires September 12, 2019              [Page 10]


Internet-Draft             SRv6-mobile-uplane                 March 2019


5.2.2.  Packet flow - Downlink

   The downlink packet flow is as follows:

   UPF2_in : (Z,A)                              -> UPF2 maps the flow w/
                                                   SID list <C1,S1, gNB>
   UPF2_out: (U2::1, C1)(gNB, S1; SL=2)(Z,A)    -> T.Encaps.Red
   C1_out  : (U2::1, S1)(gNB, S1; SL=1)(Z,A)
   S1_out  : (U2::1, gNB)(Z,A)                  -> PSP
   gNB_out : (Z,A)                              -> End.DX4 or End.DX6

   When the packet arrives at the UPF2, the UPF2 maps that particular
   flow into a UE session.  This UE session is associated with the
   policy <C1, S1, gNB>.  The UPF2 performs a T.Encaps.Red operation,
   encapsulating the packet into a new IPv6 header with its
   corresponding SRH.

   The nodes C1 and S1 perform their related Endpoint processing.

   Once the packet arrives at the gNB, the IPv6 DA corresponds to an
   End.DX4 or End.DX6 (depending on the underlying traffic).  The gNB
   decapsulates the packet, removing the IPv6 header and all its
   extensions headers and forwards the traffic toward the UE.

5.2.3.  IPv6 user-traffic

   For IPv6 user-traffic it is RECOMMENDED to perform encapsulation.
   However based on local policy, a service provider MAY choose to do
   SRH insertion.  The main benefit is a lower overhead.  In such case,
   the functions used are T.Insert.Red at gNB and End.T at UPF2 on
   Uplink, T.Insert.Red at UPF2 and End.X at gNB on Downlink.

5.3.  Enhanced mode with unchanged gNB GTP behavior

   This section describes two mechanisms for interworking with legacy
   gNBs that still use GTP: one for IPv4, the other for IPv6.

   In the interworking scenarios as illustrated in Figure 4, gNB does
   not support SRv6.  gNB supports GTP encapsulation over IPv4 or IPv6.
   To achieve interworking, a SR Gateway (SRGW-UPF1) entity is added.
   The SRGW maps the GTP traffic into SRv6.

   The SRGW is not an anchor point, and maintains very little state.
   For this reason, both IPv4 and IPv6 methods scale to millions of UEs.







Matsushima, et al.     Expires September 12, 2019              [Page 11]


Internet-Draft             SRv6-mobile-uplane                 March 2019


                                                              _______
                     IP GTP          SRv6                    /       \
    +--+      +-----+ [N3] +------+  [N9]  +------+  [N6]   /         \
    |UE|------| gNB |------| UPF1 |--------| UPF2 |---------\   DN    /
    +--+      +-----+      +------+        +------+          \_______/
                          SR Gateway       SRv6 node

                Figure 4: Example topology for interworking

5.3.1.  Interworking with IPv6 GTP

   In this interworking mode the gNB uses GTP over IPv6 via the N3
   interface

   Key points:

   o  The gNB is unchanged (control-plane or user-plane) and
      encapsulates into GTP (N3 interface is not modified).
   o  The 5G Control-Plane (N2 interface) is unmodified; one IPv6
      address is needed (i.e. a BSID at the SRGW).
   o  The SRGW removes GTP, finds the SID list related to DA, and adds
      SRH with the SID list.
   o  There is no state for the downlink at the SRGW.
   o  There is simple state in the uplink at the SRGW; using Enhanced
      mode results in fewer SR policies on this node.  A SR policy can
      be shared across UEs.
   o  When a packet from the UE leaves the gNB, it is SR-routed.  This
      simplifies network slicing [I-D.hegdeppsenak-isis-sr-flex-algo].
   o  In the uplink, the IPv6 DA BSID steers traffic into an SR policy
      when it arrives at the SRGW-UPF1.

   An example topology is shown in Figure 5.  In this mode the gNB is an
   unmodified gNB using IPv6/GTP.  The UPFs are SR-aware.  As before,
   the SRGW maps IPv6/GTP traffic to SRv6.

   S1 and C1 are two service segments.  S1 represents a VNF in the
   network, and C1 represents a router configured for Traffic
   Engineering.













Matsushima, et al.     Expires September 12, 2019              [Page 12]


Internet-Draft             SRv6-mobile-uplane                 March 2019


                                  +----+
                IPv6/GTP         -| S1 |-                            ___
   +--+  +-----+ [N3]           / +----+ \                          /
   |UE|--| gNB |-         SRv6 /   SRv6   \ +----+   +------+ [N6] /
   +--+  +-----+ \        [N9]/     VNF    -| C1 |---| UPF2 |------\  DN
           GTP    \ +------+ /              +----+   +------+       \___
                   -| UPF1 |-                SRv6      SRv6
                    +------+                  TE
                   SR Gateway

       Figure 5: Enhanced mode with unchanged gNB IPv6/GTP behavior

5.3.1.1.  Packet flow - Uplink

   The uplink packet flow is as follows:

   UE_out  : (A,Z)
   gNB_out : (gNB, B)(GTP: TEID T)(A,Z)       -> Interface N3 unmodified
                                                 (IPv6/GTP)
   SRGW_out: (SRGW, S1)(U2::1, C1; SL=2)(A,Z) -> B is an End.M.GTP6.D
                                                 SID at the SRGW
   S1_out  : (SRGW, C1)(U2::1, C1; SL=1)(A,Z)
   C1_out  : (SRGW, U2::1)(A,Z)               -> PSP
   UPF2_out: (A,Z)                            -> End.DT4 or End.DT6

   The UE sends a packet destined to Z toward the gNB on a specific
   bearer for that session.  The gNB, which is unmodified, encapsulates
   the packet into IPv6, UDP and GTP headers.  The IPv6 DA B, and the
   GTP TEID T are the ones received in the N2 interface.

   The IPv6 address that was signalled over the N2 interface for that UE
   session, B, is now the IPv6 DA.  B is an SRv6 Binding SID at the
   SRGW.  Hence the packet is routed to the SRGW.

   When the packet arrives at the SRGW, the SRGW identifies B as an
   End.M.GTP6.D Binding SID (see Section 6.3).  Hence, the SRGW removes
   the IPv6, UDP and GTP headers, and pushes an IPv6 header with its own
   SRH containing the SIDs bound to the SR policy associated with this
   BindingSID.  There is one instance of the End.M.GTP6.D SID per PDU
   type.

   S1 and C1 perform their related Endpoint functionality and forward
   the packet.

   When the packet arrives at UPF2, the active segment is (U2::1) which
   is bound to End.DT4/6.  UPF2 then decapsulates (removing the outer
   IPv6 header with all its extension headers) and forwards the packet
   toward the data network.



Matsushima, et al.     Expires September 12, 2019              [Page 13]


Internet-Draft             SRv6-mobile-uplane                 March 2019


5.3.1.2.  Packet flow - Downlink

   The downlink packet flow is as follows:

   UPF2_in : (Z,A)                           -> UPF2 maps the flow with
                                                <C1, S1, SRGW::TEID,gNB>
   UPF2_out: (U2::1, C1)(gNB, SRGW::TEID, S1; SL=3)(Z,A) -> T.Encaps.Red
   C1_out  : (U2::1, S1)(gNB, S1; SL=2)(Z,A)
   S1_out  : (U2::1, SRGW::TEID)(gNB, SRGW::TEID, S1, SL=1)(Z,A)
   SRGW_out: (SRGW, gNB)(GTP: TEID=T)(Z,A)   -> SRGW/96 is End.M.GTP6.E
   gNB_out : (Z,A)

   When a packet destined to A arrives at the UPF2, the UPF2 performs a
   lookup in the table associated to A and finds the SID list <C1, S1,
   SRGW::TEID, gNB>.  The UPF2 performs a T.Encaps.Red operation,
   encapsulating the packet into a new IPv6 header with its
   corresponding SRH.

   C1 and S1 perform their related Endpoint processing.

   Once the packet arrives at the SRGW, the SRGW identifies the active
   SID as an End.M.GTP6.E function.  The SRGW removes the IPv6 header
   and all its extensions headers.  The SRGW generates new IPv6, UDP and
   GTP headers.  The new IPv6 DA is the gNB which is the last SID in the
   received SRH.  The TEID in the generated GTP header is an argument of
   the received End.M.GTP6.E SID.  The SRGW pushes the headers to the
   packet and forwards the packet toward the gNB.  There is one instance
   of the End.M.GTP6.E SID per PDU type.

   Once the packet arrives at the gNB, the packet is a regular IPv6/GTP
   packet.  The gNB looks for the specific radio bearer for that TEID
   and forward it on the bearer.  This gNB behavior is not modified from
   current and previous generations.

5.3.1.3.  Scalability

   For the downlink traffic, the SRGW is stateless.  All the state is in
   the SRH inserted by the UPF2.  The UPF2 must have the UE states since
   it is the UE's session anchor point.

   For the uplink traffic, the state at the SRGW does not necessarily
   need to be unique per UE session; the state state can be shared among
   UEs.  This enables much more scalable SRGW deployments compared to a
   solution holding millions of states, one or more per UE.







Matsushima, et al.     Expires September 12, 2019              [Page 14]


Internet-Draft             SRv6-mobile-uplane                 March 2019


5.3.1.4.  IPv6 user-traffic

   For IPv6 user-traffic it is RECOMMENDED to perform encapsulation.
   However based on local policy, a service provider MAY choose to do
   SRH insertion.  The main benefit is lower overhead.

5.3.2.  Interworking with IPv4 GTP

   In this interworking mode the gNB uses GTP over IPv4 in the N3
   interface

   Key points:

   o  The gNB is unchanged and encapsulates packets into GTP (the N3
      interface is not modified).
   o  In the uplink, traffic is classified by SRGW's Uplink Classifier
      and steered into an SR policy.  The SRGW is a UPF1 functionality
      and can coexist with UPF1's Uplink Classifier functionality.
   o  SRGW removes GTP, finds the SID list related to DA, and adds a SRH
      with the SID list.

   An example topology is shown in Figure 6.  In this mode the gNB is an
   unmodified gNB using IPv4/GTP.  The UPFs are SR-aware.  As before,
   the SRGW maps the IPv4/GTP traffic to SRv6.

   S1 and C1 are two service segment endpoints.  S1 represents a VNF in
   the network, and C1 represents a router configured for Traffic
   Engineering.

                                  +----+
                IPv4/GTP         -| S1 |-                            ___
   +--+  +-----+ [N3]           / +----+ \                          /
   |UE|--| gNB |-         SRv6 /   SRv6   \ +----+   +------+ [N6] /
   +--+  +-----+ \        [N9]/     VNF    -| C1 |---| UPF2 |------\  DN
           GTP    \ +------+ /              +----+   +------+       \___
                   -| UPF1 |-                SRv6      SRv6
                    +------+                  TE
                   SR Gateway

       Figure 6: Enhanced mode with unchanged gNB IPv4/GTP behavior

5.3.2.1.  Packet flow - Uplink

   The uplink packet flow is as follows:







Matsushima, et al.     Expires September 12, 2019              [Page 15]


Internet-Draft             SRv6-mobile-uplane                 March 2019


    gNB_out : (gNB, B)(GTP: TEID T)(A,Z)          -> Interface N3
                                                     unchanged IPv4/GTP
    SRGW_out: (SRGW, S1)(U2::1, C1; SL=2)(A,Z)    -> T.M.Tmap function
    S1_out  : (SRGW, C1)(U2::1, C1; SL=1)(A,Z)
    C1_out  : (SRGW, U2::1) (A,Z)                 -> PSP
    UPF2_out: (A,Z)                               -> End.DT4 or End.DT6

   The UE sends a packet destined to Z toward the gNB on a specific
   bearer for that session.  The gNB, which is unmodified, encapsulates
   the packet into a new IPv4, UDP and GTP headers.  The IPv4 DA, B, and
   the GTP TEID are the ones received at the N2 interface.

   When the packet arrives at the SRGW for UPF1, the SRGW has an Uplink
   Classifier rule for incoming traffic from the gNB, that steers the
   traffic into an SR policy by using the function T.M.TMap.  The SRGW
   removes the IPv4, UDP and GTP headers and pushes an IPv6 header with
   its own SRH containing the SIDs related to the SR policy associated
   with this traffic.  The SRGW forwards according to the new IPv6 DA.

   S1 and C1 perform their related Endpoint functionality and forward
   the packet.

   When the packet arrives at UPF2, the active segment is (U2::1) which
   is bound to End.DT4/6 which performs the decapsulation (removing the
   outer IPv6 header with all its extension headers) and forwards toward
   the data network.

5.3.2.2.  Packet flow - Downlink

   The downlink packet flow is as follows:

   UPF2_in : (Z,A)                            -> UPF2 maps flow with SID
                                               <C1, S1,SRGW::SA:DA:TEID>
   UPF2_out: (U2::1, C1)(SRGW::SA:DA:TEID, S1; SL=2)(Z,A) ->T.Encaps.Red
   C1_out  : (U2::1, S1)(SRGW::SA:DA:TEID, S1; SL=1)(Z,A)
   S1_out  : (U2::1, SRGW::SA:DA:TEID)(Z,A)
   SRGW_out: (SA, DA)(GTP: TEID=T)(Z,A)       -> End.M.GTP4.E
   gNB_out : (Z,A)

   When a packet destined to A arrives at the UPF2, the UPF2 performs a
   lookup in the table associated to A and finds the SID list <C1, S1,
   SRGW::SA:DA:TEID>.  The UPF2 performs a T.Encaps.Red operation,
   encapsulating the packet into a new IPv6 header with its
   corresponding SRH.

   The nodes C1 and S1 perform their related Endpoint processing.





Matsushima, et al.     Expires September 12, 2019              [Page 16]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   Once the packet arrives at the SRGW, the SRGW identifies the active
   SID as an End.M.GTP4.E function.  The SRGW removes the IPv6 header
   and all its extensions headers.  The SRGW generates an IPv4, UDP and
   GTP headers.  The IPv4 SA and DA are received as SID arguments.  The
   TEID in the generated GTP header is also the arguments of the
   received End.M.GTP4.E SID.  The SRGW pushes the headers to the packet
   and forwards the packet toward the gNB.

   When the packet arrives at the gNB, the packet is a regular IPv4/GTP
   packet.  The gNB looks for the specific radio bearer for that TEID
   and forward it on the bearer.  This gNB behavior is not modified from
   current and previous generations.

5.3.2.3.  Scalability

   For the downlink traffic, the SRGW is stateless.  All the state is in
   the SRH inserted by the UPF.  The UPF must have this UE-base state
   anyway (since it is its anchor point).

   For the uplink traffic, the state at the SRGW is dedicated on a per
   UE/session basis according to an Uplink Classifier.  There is state
   for steering the different sessions on a SR policies.  However, SR
   policies are shared among several UE/sessions.

5.3.2.4.  IPv6 user-traffic

   For IPv6 user-traffic it is RECOMMENDED to perform encapsulation.
   Based on local policy, a service provider MAY choose to do SRH
   insertion.  The main benefit is a lower overhead.

5.3.3.  Extensions to the interworking mechanisms

   In this section we presented two mechanisms for interworking with
   gNBs that do not support SRv6.  These mechanism are done to support
   GTP over IPv4 and GTP over IPv6.

   Even though we have presented these methods as an extension to the
   "Enhanced mode", it is straightforward in its applicability to the
   "Traditional mode".

   Furthermore, although these mechanisms are designed for interworking
   with legacy RAN at the N3 interface, these methods could also be
   applied for interworking with a non-SRv6 capable UPF at the N9
   interface (e.g.  L3-anchor is SRv6 capable but L2-anchor is not).







Matsushima, et al.     Expires September 12, 2019              [Page 17]


Internet-Draft             SRv6-mobile-uplane                 March 2019


6.  SRv6 SID Mobility Functions

6.1.  Args.Mob.Session

   Args.Mob.Session provide per-session information for charging,
   buffering and lawful intercept (among others) required by some mobile
   nodes.  The Args.Mob.Session argument format is used in combination
   with End.Map, End.DT and End.DX functions.  Note that proposed format
   is applicable for 5G networks, while similar formats could be
   proposed for legacy networks.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |   QFI     |R|U|                PDU Session ID                 |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |PDU Sess(cont')|
     +-+-+-+-+-+-+-+-+

                          Args.Mob.Session format

   o  QFI: QoS Flow Identifier [TS.38415]
   o  R: Reflective QoS Indication [TS.23501].  This parameter indicates
      the activaton of reflective QoS towards the UE for the transfered
      packet.  Reflective QoS enables the UE to map UL User Plane
      traffic to QoS Flows without SMF provided QoS rules.
   o  U: Unused and for future use.  MUST be 0 on transmission and
      ignored on receipt.
   o  PDU Session ID: Identifier of PDU Session.  The GTP-U equivalent
      is TEID.

   Since the SRv6 function is likely NOT to be instantiated per PDU
   session, Args.Mob.Session helps the UPF to perform the functions
   which require per QFI and/or per PDU Session granularity.

6.2.  End.MAP

   The "Endpoint function with SID mapping" function (End.MAP for short)
   is used in several scenarios.  Particularly in mobility, End.MAP is
   used in the UPFs for the PDU Session anchor functionality.

   When a SR node N receives a packet destined to S and S is a local
   End.MAP SID, N does the following:








Matsushima, et al.     Expires September 12, 2019              [Page 18]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   1.    look up the IPv6 DA in the mapping table
   2.    update the IPv6 DA with the new mapped SID            ;; Note 1
   3.    IF segment_list > 1
   4.       insert a new SRH
   5.    forward according to the new mapped SID
   6. ELSE
   7.    Drop the packet

   Note 1: The SID in the SRH is NOT modified.

6.3.  End.M.GTP6.D

   The "Endpoint function with IPv6/GTP decapsulation into SR policy"
   function (End.M.GTP6.D for short) is used in interworking scenario
   for the uplink toward from the legacy gNB using IPv6/GTP.  Suppose,
   for example, this SID is associated with an SR policy <S1, S2, S3>
   and an IPv6 Source Address A.

   When the SR Gateway node N receives a packet destined to S and S is a
   local End.M.GTP6.D SID, N does:

   1. IF NH=UDP & UDP_PORT = GTP THEN
   2.    pop the IPv6, UDP and GTP headers
   3.    push a new IPv6 header with its own SRH <S2, S3>
   4.    set the outer IPv6 SA to A
   5.    set the outer IPv6 DA to S1
   6.    forward according to the S1 segment of the SRv6 Policy
   7. ELSE
   8.    Drop the packet

6.4.  End.M.GTP6.E

   The "Endpoint function with encapsulation for IPv6/GTP tunnel"
   function (End.M.GTP6.E for short) is used in interworking scenario
   for the downlink toward the legacy gNB using IPv6/GTP.

   The End.M.GTP6.E function has a 32-bit argument space which is used
   to provide the GTP TEID.

   When the SR Gateway node N receives a packet destined to S, and S is
   a local End.M.GTP6.E SID, N does the following:










Matsushima, et al.     Expires September 12, 2019              [Page 19]


Internet-Draft             SRv6-mobile-uplane                 March 2019


    1. IF NH=SRH & SL = 1  THEN                                ;; Note 1
    2.    decrement SL
    3.    store SRH[SL] in variable new_DA
    4.    store TEID in variable new_TEID                      ;; Note 2
    5.    pop IP header and all its extension headers
    6.    push new IPv6 header and GTP-U header
    7.    set IPv6 DA to new_DA
    8.    set GTP_TEID to new_TEID
    9.    lookup the new_DA and forward the packet accordingly
   10. ELSE
   11.    Drop the packet

   Note 1: An End.M.GTP6.E SID MUST always be the penultimate SID.

   Note 2: TEID is extracted from the argument space of the current SID.

6.5.  End.M.GTP4.E

   The "Endpoint function with encapsulation for IPv4/GTP tunnel"
   function (End.M.GTP4.E for short) is used in the downlink when doing
   interworking with legacy gNB using IPv4/GTP.

   When the SR Gateway node N receives a packet destined to S and S is a
   local End.M.GTP4.E SID, N does:

   1. IF NH=SRH & SL = 0 THEN
   2.    store SRH[0] in buffer S
   3.    pop the IPv6 header and its extension headers
   4.    push UDP/GTP headers with GTP TEID from S
   5.    push outer IPv4 header with SA, DA from S
   6. ELSE
   7.    Drop the packet

   S has the following format:

             +----------------------+-------+-------+-------+
             |  SRGW-IPv6-LOC-FUNC  |IPv4DA |IPv4SA |TUN-ID |
             +----------------------+-------+-------+-------+
                     128-a-b-c          a      b       c

                         End.M.GTP4.E SID Encoding

6.6.  T.M.Tmap

   The "Transit with tunnel decapsulation and map to an SRv6 policy"
   function (T.M.Tmap for short) is used in the direction from legacy
   user-plane to SRv6 user-plane network.




Matsushima, et al.     Expires September 12, 2019              [Page 20]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   When the SR Gateway node N receives a packet destined to a IW-
   IPv4-Prefix, N does:

   1. IF Payload == UDP/GTP THEN
   2.    pop the outer IPv4 header and UDP/GTP headers
   3.    copy IPv4 DA, SA, TUN-ID to form SID B
   4.    encapsulate the packet into a new IPv6 header
   5.    set the IPv6 DA = B
   6.    forward along the shortest path to B
   7. ELSE
   8.    Drop the packet

   B has the following format:

             +----------------------+-------+-------+-------+
             |  SRGW-IPv6-LOC-FUNC  |IPv4DA |IPv4SA |TUN-ID |
             +----------------------+-------+-------+-------+
                     128-a-b-c          a      b       c

                         End.M.GTP4.E SID Encoding

   The SID B is an SRv6 BindingSID instantiated at the first UPF (U1).
   A static format is used for this Binding SIDs in order to remove
   state from the SRGW.

6.7.  End.Limit: Rate Limiting function

   The mobile user-plane requires a rate-limit feature.  For this
   purpose, we define a new function "End.Limit".  The "End.Limit"
   function encodes in its arguments the rate limiting parameter that
   should be applied to this packet.  Multiple flows of packets should
   have the same group identifier in the SID when those flows are in an
   same AMBR group.  The encoding format of the rate limit segment SID
   is as follows:

              +----------------------+----------+-----------+
              | LOC+FUNC rate-limit  | group-id | limit-rate|
              +----------------------+----------+-----------+
                    128-i-j                i          j

             End.Limit: Rate limiting function argument format

   If the limit-rate bits are set to zero, the node should not do rate
   limiting unless static configuration or control-plane sets the limit
   rate associated to the SID.






Matsushima, et al.     Expires September 12, 2019              [Page 21]


Internet-Draft             SRv6-mobile-uplane                 March 2019


7.  SRv6 supported 3GPP PDU session types

   The 3GPP [TS.23501] defines the following PDU session types:

   o  IPv4
   o  IPv6
   o  IPv4v6
   o  Ethernet
   o  Unstructured

   SRv6 supports all the 3GPP PDU session types without any protocol
   overhead by using the corresponding SRv6 functions (End.DX4, End.DT4
   for IPv4 PDU sessions; End.DX6, End.DT6, End.T for IPv6 PDU sessions;
   End.DT46 for IPv4v6 PDU sessions; End.DX2 for L2 PDU sessions;
   End.DX2 for Unstructured PDU sessions).

8.  Network Slicing Considerations

   A mobile network may be required to implement "network slices", which
   logically separate network resources.  User-plane functions
   represented as SRv6 segments would be part of a slice.

   [I-D.filsfils-spring-segment-routing-policy] describes a solution to
   build basic network slices with SR.  Depending on the requirements,
   these slices can be further refined by adopting the mechanisms from:

   o  IGP Flex-Algo [I-D.hegdeppsenak-isis-sr-flex-algo]
   o  Inter-Domain policies
      [I-D.ietf-spring-segment-routing-central-epe]

   Furthermore, these can be combined with ODN/AS
   [I-D.filsfils-spring-segment-routing-policy] for automated slice
   provisioning and traffic steering.

   Further details on how these tools can be used to create end to end
   network slices are documented in
   [I-D.ali-spring-network-slicing-building-blocks].

9.  Control Plane Considerations

   This document focuses on user-plane behavior and its independence
   from the control plane.

   The control plane could be the current 3GPP-defined control plane
   with slight modifications to the N4 interface [TS.29244].

   Alternatively, SRv6 could be used in conjunction with a new mobility
   control plane as described in LISP [I-D.rodrigueznatal-lisp-srv6],



Matsushima, et al.     Expires September 12, 2019              [Page 22]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   hICN [I-D.auge-dmm-hicn-mobility-deployment-options], MFA
   [I-D.gundavelli-dmm-mfa] or in conjunction with FPC
   [I-D.ietf-dmm-fpc-cpdp].  The analysis of new mobility control-planes
   and its applicability to SRv6 is out of the scope of this document.

   Section 11 allocates SRv6 endpoint function types for the new
   functions defined in this document.  Control-plane protocols are
   expected to use these function type codes to signal each function.

   SRv6's network programming nature allows a flexible and dynamic UPF
   placement.

10.  Security Considerations

   TBD

11.  IANA Considerations

   IANA is requested to allocate, within the "SRv6 Endpoint Types" sub-
   registry belonging to the top-level "Segment-routing with IPv6
   dataplane (SRv6) Parameters" registry
   [I-D.filsfils-spring-srv6-network-programming], the following values:

           +-------------+-----+-------------------+-----------+
           | Value/Range | Hex | Endpoint function | Reference |
           +-------------+-----+-------------------+-----------+
           | TBA         | TBA |      End.MAP      | [This.ID] |
           | TBA         | TBA |    End.M.GTP6.D   | [This.ID] |
           | TBA         | TBA |    End.M.GTP6.E   | [This.ID] |
           | TBA         | TBA |    End.M.GTP4.E   | [This.ID] |
           | TBA         | TBA |     End.Limit     | [This.ID] |
           +-------------+-----+-------------------+-----------+

              Table 1: SRv6 Mobile User-plane Endpoint Types

12.  Acknowledgements

   The authors would like to thank Daisuke Yokota, Bart Peirens,
   Ryokichi Onishi, Kentaro Ebisawa, Peter Bosch, Darren Dukes, Francois
   Clad, Sri Gundavelli, Sridhar Bhaskaran, Arashmid Akhavain, Ravi
   Shekhar and Aeneas Dodd-Noble for their useful comments of this work.

13.  Contributors

   Kentaro Ebisawa
   Ponto Networks
   Japan




Matsushima, et al.     Expires September 12, 2019              [Page 23]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   Email: ebiken@pontonetworks.com

14.  References

14.1.  Normative References

   [I-D.filsfils-spring-segment-routing-policy]
              Filsfils, C., Sivabalan, S., Hegde, S.,
              daniel.voyer@bell.ca, d., Lin, S., bogdanov@google.com,
              b., Krol, P., Horneffer, M., Steinberg, D., Decraene, B.,
              Litkowski, S., Mattes, P., Ali, Z., Talaulikar, K., Liste,
              J., Clad, F., and K. Raza, "Segment Routing Policy
              Architecture", draft-filsfils-spring-segment-routing-
              policy-06 (work in progress), May 2018.

   [I-D.filsfils-spring-srv6-network-programming]
              Filsfils, C., Camarillo, P., Leddy, J.,
              daniel.voyer@bell.ca, d., Matsushima, S., and Z. Li, "SRv6
              Network Programming", draft-filsfils-spring-srv6-network-
              programming-07 (work in progress), February 2019.

   [I-D.ietf-6man-segment-routing-header]
              Filsfils, C., Previdi, S., Leddy, J., Matsushima, S., and
              d. daniel.voyer@bell.ca, "IPv6 Segment Routing Header
              (SRH)", draft-ietf-6man-segment-routing-header-16 (work in
              progress), February 2019.

   [I-D.voyer-6man-extension-header-insertion]
              daniel.voyer@bell.ca, d., Leddy, J., Filsfils, C., Dukes,
              D., Previdi, S., and S. Matsushima, "Insertion of IPv6
              Segment Routing Headers in a Controlled Domain", draft-
              voyer-6man-extension-header-insertion-05 (work in
              progress), January 2019.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.








Matsushima, et al.     Expires September 12, 2019              [Page 24]


Internet-Draft             SRv6-mobile-uplane                 March 2019


14.2.  Informative References

   [I-D.ali-spring-network-slicing-building-blocks]
              Ali, Z., Filsfils, C., Camarillo, P., and d.
              daniel.voyer@bell.ca, "Building blocks for Slicing in
              Segment Routing Network", draft-ali-spring-network-
              slicing-building-blocks-01 (work in progress), March 2019.

   [I-D.auge-dmm-hicn-mobility-deployment-options]
              Auge, J., Carofiglio, G., Muscariello, L., and M.
              Papalini, "Anchorless mobility management through hICN
              (hICN-AMM): Deployment options", draft-auge-dmm-hicn-
              mobility-deployment-options-01 (work in progress),
              December 2018.

   [I-D.camarillo-dmm-srv6-mobile-pocs]
              Camarillo, P., Filsfils, C., Bertz, L., Akhavain, A.,
              Matsushima, S., and d. daniel.voyer@bell.ca, "Segment
              Routing IPv6 for mobile user-plane PoCs", draft-camarillo-
              dmm-srv6-mobile-pocs-01 (work in progress), October 2018.

   [I-D.camarilloelmalky-springdmm-srv6-mob-usecases]
              Camarillo, P., Filsfils, C., Elmalky, H., Matsushima, S.,
              daniel.voyer@bell.ca, d., Cui, A., and B. Peirens, "SRv6
              Mobility Use-Cases", draft-camarilloelmalky-springdmm-
              srv6-mob-usecases-01 (work in progress), January 2019.

   [I-D.gundavelli-dmm-mfa]
              Gundavelli, S., Liebsch, M., and S. Matsushima, "Mobility-
              aware Floating Anchor (MFA)", draft-gundavelli-dmm-mfa-01
              (work in progress), September 2018.

   [I-D.hegdeppsenak-isis-sr-flex-algo]
              Psenak, P., Hegde, S., Filsfils, C., and A. Gulko, "ISIS
              Segment Routing Flexible Algorithm", draft-hegdeppsenak-
              isis-sr-flex-algo-02 (work in progress), February 2018.

   [I-D.ietf-dmm-fpc-cpdp]
              Matsushima, S., Bertz, L., Liebsch, M., Gundavelli, S.,
              Moses, D., and C. Perkins, "Protocol for Forwarding Policy
              Configuration (FPC) in DMM", draft-ietf-dmm-fpc-cpdp-12
              (work in progress), June 2018.

   [I-D.ietf-spring-segment-routing-central-epe]
              Filsfils, C., Previdi, S., Dawra, G., Aries, E., and D.
              Afanasiev, "Segment Routing Centralized BGP Egress Peer
              Engineering", draft-ietf-spring-segment-routing-central-
              epe-10 (work in progress), December 2017.



Matsushima, et al.     Expires September 12, 2019              [Page 25]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   [I-D.rodrigueznatal-lisp-srv6]
              Rodriguez-Natal, A., Ermagan, V., Maino, F., Dukes, D.,
              Camarillo, P., and C. Filsfils, "LISP Control Plane for
              SRv6 Endpoint Mobility", draft-rodrigueznatal-lisp-srv6-01
              (work in progress), January 2019.

   [I-D.xuclad-spring-sr-service-programming]
              Clad, F., Xu, X., Filsfils, C., daniel.bernier@bell.ca,
              d., Li, C., Decraene, B., Ma, S., Yadlapalli, C.,
              Henderickx, W., and S. Salsano, "Service Programming with
              Segment Routing", draft-xuclad-spring-sr-service-
              programming-01 (work in progress), October 2018.

   [TS.23501]
              3GPP, "System Architecture for the 5G System", 3GPP TS
              23.501 15.0.0, November 2017.

   [TS.29244]
              3GPP, "Interface between the Control Plane and the User
              Plane Nodes", 3GPP TS 29.244 15.0.0, December 2017.

   [TS.29281]
              3GPP, "General Packet Radio System (GPRS) Tunnelling
              Protocol User Plane (GTPv1-U)", 3GPP TS 29.281 15.1.0,
              December 2017.

   [TS.38415]
              3GPP, "Draft Specification for 5GS container (TS 38.415)",
              3GPP R3-174510 0.0.0, August 2017.

Appendix A.  Implementations

   This document introduces new SRv6 functions.  These functions have an
   open-source P4 implementation available in
   <https://github.com/ebiken/p4srv6>.

   There are also implementations in M-CORD NGIC and Open Air Interface
   (OAI).  Further details can be found in
   [I-D.camarillo-dmm-srv6-mobile-pocs].

Appendix B.  Changes from revision 02 to revision 03

   This section lists the changes between draft-ietf-dmm-srv6-mobile-
   uplane revisions ...-02 and ...-03.

   o  Added new terminology section for abbreviations.
   o  Added new terminology section for predefined SRv6 functions.
   o  Made terminology section for conventions used in the document.



Matsushima, et al.     Expires September 12, 2019              [Page 26]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   o  Renamed "Basic" mode to be called "Traditional" mode.
   o  Renamed "Aggregate" mode to be called "Enhanced" mode.
   o  Added new Args.Mob.Session format to supply QFI, RQI indication
      and PDU Session ID.
   o  Modified End.MAP function to define the SID argument format and
      support more than one SID
   o  Added missing references.
   o  Editorial updates to improve readability.

Authors' Addresses

   Satoru Matsushima
   SoftBank
   Tokyo
   Japan

   Email: satoru.matsushima@g.softbank.co.jp


   Clarence Filsfils
   Cisco Systems, Inc.
   Belgium

   Email: cf@cisco.com


   Miya Kohno
   Cisco Systems, Inc.
   Japan

   Email: mkohno@cisco.com


   Pablo Camarillo Garvia
   Cisco Systems, Inc.
   Spain

   Email: pcamaril@cisco.com


   Daniel Voyer
   Bell Canada
   Canada

   Email: daniel.voyer@bell.ca






Matsushima, et al.     Expires September 12, 2019              [Page 27]


Internet-Draft             SRv6-mobile-uplane                 March 2019


   Charles E. Perkins
   Futurewei Inc.
   2330 Central Expressway
   Santa Clara, CA  95050
   USA

   Phone: +1-408-330-4586
   Email: charliep@computer.org











































Matsushima, et al.     Expires September 12, 2019              [Page 28]