DHCWG I. Farrer
Internet-Draft Deutsche Telekom AG
Updates: 7598 (if approved) Q. Sun
Intended status: Standards Track Y. Cui
Expires: September 18, 2018 L. Sun
Tsinghua University
March 17, 2018
DHCPv4 over DHCPv6 Source Address Option
draft-ietf-dhc-dhcp4o6-saddr-opt-02
Abstract
DHCPv4 over DHCPv6 is a mechanism for dynamically configuring IPv4
over an IPv6-only network. For DHCPv4 over DHCPv6 to function with
some IPv4-over-IPv6 softwire mechanisms and deployment scenarios, the
operator needs to know the IPv6 address that the client will use as
the source of IPv4-in-IPv6 softwire tunnel. This address, in
conjunction with the client's IPv4 address and (in some deployments),
the Port Set ID are used to create a binding table entry in the
operator's softwire tunnel concentrator. This memo defines a DHCPv6
option to convey IPv6 parameters for establishing the softwire tunnel
and a DHCPv4 option (to be used only with DHCP 4o6) to communicate
the source tunnel IPv6 address between the DHCP 4o6 client and
server. It is designed to work in conjunction with the IPv4 address
allocation process. This document updates "DHCPv6 Options for
Configuration of Softwire Address and Port-Mapped Clients" to allow
the DHCPv6 option OPTION_S46_BR (90) to appear outside of DHCPv6
softwire container options.
This document updates RFC7598, allowing OPTION_S46_BR (90) to be
enumerated in the DHCPv6 client's ORO request and appear directly
within subsequent messages sent by the DHCPv6 server.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
Farrer, et al. Expires September 18, 2018 [Page 1]
Internet-Draft DHCP 4o6 SADDR option March 2018
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 18, 2018.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Applicability . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Requirements Language . . . . . . . . . . . . . . . . . . . . 4
4. Solution Overview . . . . . . . . . . . . . . . . . . . . . . 4
4.1. Updating RFC7598 to Permit the Reuse of OPTION_S46_BR(90) 4
5. DHCP 4o6 IPv6/IPv4 Binding Message Flow . . . . . . . . . . . 5
6. DHCP Options . . . . . . . . . . . . . . . . . . . . . . . . 7
6.1. DHCPv6 Softwire Source Binding Prefix Hint Option . . . . 7
6.2. DHCPv4 over DHCPv6 Softwire Source Address Option . . . . 7
7. Client Behavior . . . . . . . . . . . . . . . . . . . . . . . 8
7.1. Client Initialization . . . . . . . . . . . . . . . . . . 8
7.2. Renewing or Rebinding the IPv4 Address Lease and
Softwire Source Address . . . . . . . . . . . . . . . . . 9
7.2.1. Changing the Bound IPv6 Softwire Source Address . . . 10
7.3. Releasing the IPv4 Address Lease and Softwire
Source Address . . . . . . . . . . . . . . . . . . . . . 10
7.4. OPTION_S46_BIND_IPV6_PREFIX Validation Behavior . . . . . 10
7.5. Client and Server Softwire Source Address Mismatch . . . 11
7.6. Use With Dynamic, Shared IPv4 Addresses . . . . . . . . . 11
8. Server Behavior . . . . . . . . . . . . . . . . . . . . . . . 11
8.1. Changing the Bound IPv6 Source Address . . . . . . . . . 11
9. Security Considerations . . . . . . . . . . . . . . . . . . . 12
10. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 12
11. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 12
12. References . . . . . . . . . . . . . . . . . . . . . . . . . 12
12.1. Normative References . . . . . . . . . . . . . . . . . . 12
Farrer, et al. Expires September 18, 2018 [Page 2]
Internet-Draft DHCP 4o6 SADDR option March 2018
12.2. Informative References . . . . . . . . . . . . . . . . . 12
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 13
1. Introduction
Deterministic IPv4-over-IPv6 transition technologies require that
elements are pre-configured with binding rules for routing traffic to
clients. This places a constraint on the choice of address used as
the client's softwire source address: it must use a pre-determined
prefix which is usually configured on the home gateway device.
[RFC7597] describes a DHCPv6 based mechanism for provisioning such
deterministic softwires.
A dynamic provisioning model, such as using DHCPv4 over DHCPv6
[RFC7341] (DHCP 4o6) allows much more flexibility in the location of
the IPv4-over-IPv6 softwire source address. In this model, the IPv6
address is dynamically communicated back to the service provider
allowing the corresponding softwire configuration to be created in
the border router (BR).
The DHCP 4o6 client and softwire client could be run on end devices
attached to any routable IPv6 prefix allocated to an end-user,
located anywhere within an arbitrary home network topology. Dynamic
allocation also helps to optimize IPv4 resource usage as only clients
which are actively renewing their IPv4 lease hold on to the address.
This document describes a mechanism for dynamically provisioning
softwires created using DHCP 4o6, including provisioning the client
with the address of the softwire border router (BR) and informing the
service provider of client's binding between the dynamically
allocated IPv4 address and Port Set ID and the IPv6 address that the
softwire Initiator will use for accessing IPv4-over-IPv6 services.
The mechanism operates alongside the DHCP 4o6 message flows to
communicate the binding information over the IPv6-only network. The
DHCP 4o6 server provides a single point in the network which holds
the current client binding information. The service provider can
then use this binding information to provision other functional
elements, such as the BR(s).
2. Applicability
The mechanism described in this document is only suitable for use for
provisioning softwire clients via DHCP 4o6. The options described
here are only applicable within the DHCP 4o6 message exchange
process. Current softwire technologies suitable for extending to
incorporate DHCP 4o6 with dynamic IPv4 address leasing include
[RFC7597] and [RFC7596].
Farrer, et al. Expires September 18, 2018 [Page 3]
Internet-Draft DHCP 4o6 SADDR option March 2018
3. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
4. Solution Overview
In order to provision a softwire, both IPv6 and IPv4 configuration
needs to be passed to the client. To map this to the DHCP 4o6
configuration process, the IPv6 configuration is carried in DHCPv6
options carried inside the DHCPv6 message DHCPV4-RESPONSE (21) sent
by the server. OPTION_S46_BR (90) is used to provision the remote
IPv6 address for the softwire (see Section 4.1 below).
OPTION_S46_BIND_IPV6_PREFIX (TBD1), is optionally sent by the DHCP
4o6 server to indicate to the client a preferred IPv6 prefix for
binding the received IPv4 configuration and sourcing tunnel traffic.
This may be necessary if there are multiple IPv6 prefixes in use in
the customer network (e.g. ULAs), or if the specific IPv4-over-IPv6
transition mechanism requires the use of a particular prefix for any
reason.
IPv4 configuration is carried in DHCPv4 messages (inside the DHCP 4o6
option OPTION_DHCPV4_MSG (87)) using the mechanism described in
[RFC7341].
In order for the client to communicate the softwire source address, a
new DHCPv4 option OPTION_DHCP4O6_S46_SADDR (TBD2) is defined in this
document. This is included in DHCPREQUEST messages sent by the
client and is stored by the server for the lifetime of the IPv4
address lease.
4.1. Updating RFC7598 to Permit the Reuse of OPTION_S46_BR(90)
Section 4.2 of [RFC7598] defines option OPTION_S46_BR(90) for
communicating remote softwire border relay (BR)'s' IPv6 address(es)
to a client, but mandates that the option can only be used when
encapsulated within one of the softwire container options:
OPTION_S46_CONT_MAPE (94) or OPTION_S46_CONT_LW(96). From Section 3
of [RFC7598]:
"Softwire46 DHCPv6 clients that receive provisioning options that
are not encapsulated in container options MUST silently ignore
these options."
This document updates [RFC7598], removing this restriction for
OPTION_S46_BR (90), allowing it to be enumerated in the client's ORO
Farrer, et al. Expires September 18, 2018 [Page 4]
Internet-Draft DHCP 4o6 SADDR option March 2018
request and appear directly within subsequent messages sent by the
DHCPv6 server.
5. DHCP 4o6 IPv6/IPv4 Binding Message Flow
The following diagram shows the relevant extensions to the successful
DHCP 4o6 IPv4 allocation client/server message flow for the softwire
source address function. The full process, including error handling
is described in Section 7.
In each step, the DHCPv6 portion of the message and any relevant
option is shown above the arrow. The DHCP 4o6 content of the message
and its relevant options are below the arrow. All the DHCPv4
messages are encapsulated in DHCPV4-QUERY (20) or DHCPV4-RESPONSE
(21) messages. Where relevant, the necessary options and their
contents are shown.
Farrer, et al. Expires September 18, 2018 [Page 5]
Internet-Draft DHCP 4o6 SADDR option March 2018
DHCP 4o6 DHCP 4o6
Client Server
| |
| DHCPv6 - DHCPV4-QUERY message containing |
| OPTION_ORO(6) listing (90, TBD1) |
Step 1 |----------------------------------------------------->|
| DHCPv4 - DHCPDISCOVER message |
| |
| |
| DHCPv6 - DHCPV4-RESPONSE message containing |
| OPTION_S46_BR(90), OPTION_S46_BIND_IPV6_PREFIX(TDB1) |
| (bind-ipv6-prefix with service provider's |
| preferred prefix) |
Step 2 |<-----------------------------------------------------|
| DHCPv4 - DHCPOFFER message |
| |
| |
| DHCPv6 - DHCPV4-QUERY message |
Step 3 |----------------------------------------------------->|
| DHCPv4 - DHCPREQUEST message containing |
| OPTION_DHCP4O6_S46_SADDR (softwire-ipv6-src-address |
| with client's bound IPv6 softwire source address) |
| |
| |
| DHCPv6 - DHCPV4-RESPONSE message |
Step 4 |<-----------------------------------------------------|
| DHCPv4 - DHCPACK message containing |
| OPTION_DHCP4O6_S46_SADDR (softwire-ipv6-src-address |
| with client's bound IPv6 softwire source address) |
| |
Figure 1: IPv6/IPv4 Binding Message Flow
Step 1 The client constructs a DHCPv6 'DHCPV4-QUERY(20)' message.
This message contains two options: DHCPv6 OPTION_ORO (6) and
OPTION_DHCPV4_MSG (87). OPTION_ORO lists '90'
(OPTION_S46_BR) and 'TBD1' (OPTION_S46_BIND_IPV6_PREFIX).
OPTION_DHCPV4_MSG contains a DHCPv4 DHCPDISCOVER message.
Step 2 The server responds with a DHCPv6 'DHCPV4-RESPONSE (21)'
message. This message contains OPTION_S46_BR (90) containing
the IPv6 address of the BR for the client's softwire
configuration. The message may also, optionally contain
OPTION_S46_BIND_IPV6_PREFIX (TBD1). OPTION_DHCPV4_MSG
contains a DHCPv4 DHCPOFFER message.
Step 3 The client sends with a DHCPv6 'DHCPV4-QUERY(20)' message
containing a DHCPv4 DHCPREQUEST message with
Farrer, et al. Expires September 18, 2018 [Page 6]
Internet-Draft DHCP 4o6 SADDR option March 2018
OPTION_DHCP4O6_S46_SADDR (TBD2) with the IPv6 address which
the client will use as its softwire source address.
Step 4 The server sends a DHCPv6 'DHCPV4-RESPONSE(21)' message.
OPTION_DHCPV4_MSG contains a DHCPv4 DHCPACK message.
OPTION_DHCP4O6_S46_SADDR with the client's softwire source
address is included.
6. DHCP Options
6.1. DHCPv6 Softwire Source Binding Prefix Hint Option
The format of DHCPv6 Source Binding Prefix hint option is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPTION_S46_BIND_IPV6_PREFIX | option-length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|bindprefix6-len| |
+-+-+-+-+-+-+-+-+ bind-ipv6-prefix .
. (variable length) .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Format of OPTION_S46_BIND_IPV6_PREFIX
o option-code: OPTION_S46_BIND_IPV6_PREFIX (TBD1)
o option-length: 1 + length of bind-ipv6-prefix, specified in bytes.
o bindprefix6-len: 8-bit field expressing the bit mask length of the
IPv6 prefix specified in bind-ipv6-prefix. Valid values are 0 to
128.
o bind-ipv6-prefix: The IPv6 prefix indicating the preferred prefix
for the client to bind the received IPv4 configuration to. The
length is (bindprefix6-len + 7) / 8. The field is padded on the
right with zero bits up to the next octet boundary when bind-
ipv6-prefix is not evenly divisible by 8.
OPTION_S46_BIND_IPV6_PREFIX is a singleton. Servers MUST NOT send
more than one instance of the OPTION_S46_BIND_IPV6_PREFIX option.
6.2. DHCPv4 over DHCPv6 Softwire Source Address Option
The format of DHCPv4 over DHCPv6 softwire source address option is as
follows:
Farrer, et al. Expires September 18, 2018 [Page 7]
Internet-Draft DHCP 4o6 SADDR option March 2018
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
| option-code (TBD) | option-length |
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
+ softwire-ipv6-src-address +
. (128 bits) .
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
Format of OPTION_DHCP4O6_S46_SADDR
o option-code: OPTION_DHCP4O6_S46_SADDR (TBD2)
o option-length: 16.
o softwire-ipv6-src-address: 16 bytes long; The IPv6 address that is
associated (either being requested for binding or currently bound)
with the client's IPv4 configuration.
NB - The function of OPTION_DHCP4O6_S46_SADDR may seem similar to the
DHCPv4 message's 'chaddr' field, or the Client Identifier (61) option
in that it provides a lower-layer address which is unique that the
server can use for identifying the client. However, as both of these
are required to remain constant throughout the address lease
lifetime, they cannot be used with the mechanism described in this
document. This is because the client may only be able to construct
the IPv6 address to use as the source address after it has received
the first DHCPV4-RESPONSE message from the server containing
OPTION_S46_BIND_IPV6_PREFIX.
7. Client Behavior
A client requiring dynamic softwire configuration first enables DHCP
4o6 configuration using the method described in Section 5. of
[RFC7341]. If OPTION_DHCP4_O_DHCP6_SERVER is received in the
corresponding REPLY message, the client MAY continue with the
configuration process described below.
It is also a prerequisite that the client has already learned a
suitable IPv6 prefix to use for its local softwire endpoint using
DHCPv6, RA/PIO or another mechanism.
7.1. Client Initialization
When constructing the initial DHCP 4o6 DHCPDISCOVER message, the
client includes a DHCPv6 OPTION_ORO (6) within the options field of
the DHCP-QUERY message. OPTION_ORO contains the option codes for
OPTION_S46_BR (90) and OPTION_S46_BIND_IPV6_PREFIX (TBD1).
Farrer, et al. Expires September 18, 2018 [Page 8]
Internet-Draft DHCP 4o6 SADDR option March 2018
On receipt of the DHCP 4o6 server's reply (a DHCPV4-RESPONSE
containing a DHCPOFFER message), the client checks the contents of
the DHCPv4-RESPONSE for the presence of a valid OPTION_S46_BR option.
If this option is not present, or does not contain at least one valid
IPv6 address for a BR, then the client MUST discard the message, as
without the address of the BR the client cannot configure the
softwire and so has no interface to request IPv4 configuration for.
The DHCPV4-RESPONSE message may also include
OPTION_S46_BIND_IPV6_PREFIX, which is used by the operator to
indicate a preferred prefix that the client should use to bind IPv4
configuration to. If received, the client first checks the option
according to Section 7.4. If valid, the client uses this prefix as
the 'IPv6 binding prefix' and follows to the process described in
Section 5.1 of [RFC7596] in order to select an active IPv6 prefix to
construct the softwire. If no match is found, or the client doesn't
receive OPTION_S46_BIND_IPV6_PREFIX the client MAY select any valid
IPv6 prefix (of a suitable scope) to use as the tunnel source.
Once the client has selected a suitable prefix, it MAY use either an
existing IPv6 address that is already configured on an interface, or
create a new address specifically for use as the softwire source
address (e.g. using an Interface Identifier constructed as per
Section 6. of [RFC7597]). If a new address is being created, the
client MUST complete configuration of the new address, performing
duplicate address detection (if required) before proceeding.
The client then constructs a DHCPV4-QUERY message containing a DHCPv4
DHCPREQUEST message. OPTION_DHCP4O6_S46_SADDR is included in the
options field of the DHCPREQUEST message with the IPv6 address of its
softwire source address in the softwire-ipv6-src-address field.
When the client receives a DHCPv4 DHCPACK message from the server, it
checks the IPv6 address in OPTION_DHCP4O6_S46_SADDR against its
active softwire source address. If they match, the allocation
process has concluded. If there is a discrepancy then the process
described in Section 7.5 is followed.
If the client receives a DHCPv4 DHCPNAK message from the server, then
the configuration process has been unsuccessful. The client then
restarts the process from Step 1 of Figure 1.
7.2. Renewing or Rebinding the IPv4 Address Lease and Softwire Source
Address
Whenever the client attempts to extend the lease time of the IPv4
address, OPTION_DHCP4O6_S46_SADDR with the IPv6 address of its
Farrer, et al. Expires September 18, 2018 [Page 9]
Internet-Draft DHCP 4o6 SADDR option March 2018
softwire source address in the softwire-ipv6-src-address field MUST
be included in the DHCPREQUEST message.
7.2.1. Changing the Bound IPv6 Softwire Source Address
Across the lifetime of the leased IPv4 address, it is possible that
the client's IPv6 will change. E.g. if there is a flash IPv6 re-
numbering event.
In this situation, the client MUST inform the server of the new
address. This is done by sending a DHCPREQUEST message containing
OPTION_DHCP4O6_S46_SADDR with the new IPv6 source address.
When the client receives a DHCPv4 DHCPACK message from the server, it
checks the IPv6 address in OPTION_DHCP4O6_S46_SADDR against its
active softwire source address. If they match, the allocation
process has concluded. If there is a discrepancy then the process
described in Section 7.5 is followed.
If the client receives a DHCPv4 DHCPNAK message in repsonse from the
server, then the change of the bound IPv6 Softwire source address has
been unsuccessful. In this case, the client MUST stop using the new
IPv6 source address. The client then restarts the process from Step
1 of Figure 1.
7.3. Releasing the IPv4 Address Lease and Softwire Source Address
When the client no longer requires the IPv4 resource, it sends a
DHCPv4 DHCPRELEASE message to the server. As the options field is
unused in this message type, OPTION_DHCP4O6_S46_SADDR is not
included.
7.4. OPTION_S46_BIND_IPV6_PREFIX Validation Behavior
On receipt of the OPTION_S46_BIND_IPV6_PREFIX option, the client
makes the following validation checks:
o The received bindprefix6-len value is not larger than 128.
o The received bindprefix6-len value is not larger than the number
of bytes sent in the bind-ipv6-prefix field. (e.g. the
bindprefix6-len is 128 but the bind-ipv6-prefix has only 8 bytes).
For either of these cases the receiver MAY either discard the option
and proceed to attempt configuration as if the option had not been
received, or attempt to use the received values for the longest
prefix match anyway.
Farrer, et al. Expires September 18, 2018 [Page 10]
Internet-Draft DHCP 4o6 SADDR option March 2018
The receiver MUST only use bits from the bind-ipv6-prefix field up to
the value specified in the bindprefix6-len when performing the
longest prefix match. bind-ipv6-prefix bits beyond this value MUST be
ignored.
7.5. Client and Server Softwire Source Address Mismatch
If the client receives a DHCPACK message with an
OPTION_DHCP4O6_S46_SADDR containing an IPv6 address which differs
from its active softwire source address, the client MAY either:
o Wait for a randomised time interval and then resend a DHCPREQUEST
message with the correct softwire source address, OR
o Send a DHCPRELEASE message and re-start the process described in
Section 7.
7.6. Use With Dynamic, Shared IPv4 Addresses
[RFC7618]describes a mechanism for using DHCPv4 to distribute
dynamic, shared IPv4 addresses to clients. The mechanism described
in this document is compatible with IPv4 address sharing, and can be
enabled by following the process described in Section 6 of [RFC7618].
8. Server Behavior
Beyond the normal DHCP 4o6 functionality defined in [RFC7341], the
server MUST also store the IPv6 softwire source address of the client
in the leasing address database, alongside the IPv4 address and
client identifier. An OPTION_DHCP4O6_S46_SADDR containing the bound
softwire source address MUST be sent in every DHCPACK message sent by
the server.
The binding entry between the client's IPv6 softwire source address
and the leased IPv4 address is valid as long as the IPv4 lease
remains valid.
8.1. Changing the Bound IPv6 Source Address
In the event that the server receives a DHCPREQUEST message for an
active IPv4 lease containing a OPTION_DHCP4O6_S46_SADDR with an IPv6
address which differs from the address which is currently stored, the
server updates the stored softwire source address with the new
address supplied by the client, and sends a DHCPACK message
containing the updated softwire source address in
OPTION_DHCP4O6_S46_SADDR.
The server MAY implement a policy enforcing a minimum time interval
between a client updating its softwire source IPv6 address. If a
Farrer, et al. Expires September 18, 2018 [Page 11]
Internet-Draft DHCP 4o6 SADDR option March 2018
client attempts to update the softwire source IPv6 address before the
minimum time has expired, the server can either silently drop the
client's message or send back a DHCPACK message containing the
exisiting IPv6 address binding in OPTION_DHCP4O6_S46_SADDR.
9. Security Considerations
Security considerations which are applicable to [RFC7341] are also
applicable here.
10. IANA Considerations
IANA is requested to assign the OPTION_DHCP4O6_S46_SADDR option code
from the "BOOTP Vendor Extensions and DHCP Options" registry
maintained at http://www.iana.org/assignments/bootp-dhcp-parameters.
IANA is requested to assign the OPTION_S46_BIND_IPV6_PREFIX option
code from the DHCPv6 "Option Codes" registry maintained at
http://www.iana.org/assignments/dhcpv6-parameters.
11. Acknowledgements
The authors would like to thank Ted Lemon, Lishan Li, Tatuya Jinmei,
Jonas Gorski and Razvan Becheriu for their contributions and
comments.
12. References
12.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC7341] Sun, Q., Cui, Y., Siodelski, M., Krishnan, S., and I.
Farrer, "DHCPv4-over-DHCPv6 (DHCP 4o6) Transport",
RFC 7341, DOI 10.17487/RFC7341, August 2014,
<https://www.rfc-editor.org/info/rfc7341>.
12.2. Informative References
[RFC7596] Cui, Y., Sun, Q., Boucadair, M., Tsou, T., Lee, Y., and I.
Farrer, "Lightweight 4over6: An Extension to the Dual-
Stack Lite Architecture", RFC 7596, DOI 10.17487/RFC7596,
July 2015, <https://www.rfc-editor.org/info/rfc7596>.
Farrer, et al. Expires September 18, 2018 [Page 12]
Internet-Draft DHCP 4o6 SADDR option March 2018
[RFC7597] Troan, O., Ed., Dec, W., Li, X., Bao, C., Matsushima, S.,
Murakami, T., and T. Taylor, Ed., "Mapping of Address and
Port with Encapsulation (MAP-E)", RFC 7597,
DOI 10.17487/RFC7597, July 2015,
<https://www.rfc-editor.org/info/rfc7597>.
[RFC7598] Mrugalski, T., Troan, O., Farrer, I., Perreault, S., Dec,
W., Bao, C., Yeh, L., and X. Deng, "DHCPv6 Options for
Configuration of Softwire Address and Port-Mapped
Clients", RFC 7598, DOI 10.17487/RFC7598, July 2015,
<https://www.rfc-editor.org/info/rfc7598>.
[RFC7618] Cui, Y., Sun, Q., Farrer, I., Lee, Y., Sun, Q., and M.
Boucadair, "Dynamic Allocation of Shared IPv4 Addresses",
RFC 7618, DOI 10.17487/RFC7618, August 2015,
<https://www.rfc-editor.org/info/rfc7618>.
Authors' Addresses
Ian Farrer
Deutsche Telekom AG
CTO-ATI, Landgrabenweg 151
Bonn, NRW 53227
Germany
Email: ian.farrer@telekom.de
Qi Sun
Tsinghua University
Beijing 100084
P.R. China
Phone: +86-10-6278-5822
Email: sunqi.csnet.thu@gmail.com
Yong Cui
Tsinghua University
Beijing 100084
P.R. China
Phone: +86-10-6260-3059
Email: yong@csnet1.cs.tsinghua.edu.cn
Farrer, et al. Expires September 18, 2018 [Page 13]
Internet-Draft DHCP 4o6 SADDR option March 2018
Linhui Sun
Tsinghua University
Beijing 100084
P.R. China
Phone: +86-10-6278-5822
Email: lh.sunlinh@gmail.com
Farrer, et al. Expires September 18, 2018 [Page 14]