Network Working Group P. Hoffman
Internet-Draft VPN Consortium
Intended status: Standards Track J. Schlyter
Expires: September 10, 2012 Kirei AB
March 9, 2012
The DNS-Based Authentication of Named Entities (DANE) Protocol for
Transport Layer Security (TLS)
draft-ietf-dane-protocol-18
Abstract
Encrypted communication on the Internet often uses Transport Level
Security (TLS), which depends on third parties to certify the keys
used. This document improves on that situation by enabling the
administrator of a domain name to certify the keys used in that
domain's TLS servers. This requires matching improvements in TLS
client software, but no change in TLS server software.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 10, 2012.
Copyright Notice
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
Hoffman & Schlyter Expires September 10, 2012 [Page 1]
Internet-Draft DNS-Based Authentication for TLS March 2012
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1. Background of the Problem . . . . . . . . . . . . . . . . 4
1.2. Securing the Association with a Server's Certificate . . . 5
1.3. Method For Securing Certificate Associations . . . . . . . 6
1.4. Terminology . . . . . . . . . . . . . . . . . . . . . . . 6
2. The TLSA Resource Record . . . . . . . . . . . . . . . . . . . 7
2.1. TLSA RDATA Wire Format . . . . . . . . . . . . . . . . . . 7
2.1.1. The Certificate Usage Field . . . . . . . . . . . . . 7
2.1.2. The Selector Field . . . . . . . . . . . . . . . . . . 8
2.1.3. The Matching Type Field . . . . . . . . . . . . . . . 9
2.1.4. The Certificate Association Data Field . . . . . . . . 9
2.2. TLSA RR Presentation Format . . . . . . . . . . . . . . . 9
2.3. TLSA RR Examples . . . . . . . . . . . . . . . . . . . . . 10
3. Domain Names for TLS Certificate Associations . . . . . . . . 10
4. Use of TLSA Records in TLS . . . . . . . . . . . . . . . . . . 11
5. TLSA and DANE Use Cases and Requirements . . . . . . . . . . . 12
6. Mandatory-to-Implement Features . . . . . . . . . . . . . . . 14
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 14
7.1. TLSA RRtype . . . . . . . . . . . . . . . . . . . . . . . 14
7.2. TLSA Usages . . . . . . . . . . . . . . . . . . . . . . . 14
7.3. TLSA Selectors . . . . . . . . . . . . . . . . . . . . . . 15
7.4. TLSA Matching Types . . . . . . . . . . . . . . . . . . . 15
8. Security Considerations . . . . . . . . . . . . . . . . . . . 16
8.1. DNS Caching . . . . . . . . . . . . . . . . . . . . . . . 17
9. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 18
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 18
10.1. Normative References . . . . . . . . . . . . . . . . . . . 18
10.2. Informative References . . . . . . . . . . . . . . . . . . 19
Appendix A. Operational Considerations for Deploying TLSA
Records . . . . . . . . . . . . . . . . . . . . . . . 19
A.1. Creating TLSA Records . . . . . . . . . . . . . . . . . . 20
A.1.1. Ambiguities and Corner Cases When TLS Clients
Build Trust Chains . . . . . . . . . . . . . . . . . . 20
A.1.2. Choosing a Selector Type . . . . . . . . . . . . . . . 21
A.2. Provisioning TLSA Records in DNS . . . . . . . . . . . . . 23
A.2.1. Provisioning TLSA Records with Aliases . . . . . . . . 23
A.3. Securing the Last Hop . . . . . . . . . . . . . . . . . . 25
A.4. Handling Certificate Rollover . . . . . . . . . . . . . . 26
Appendix B. Pseudocode for Using TLSA . . . . . . . . . . . . . . 26
B.1. Helper Functions . . . . . . . . . . . . . . . . . . . . . 26
B.2. Main TLSA Pseudo Code . . . . . . . . . . . . . . . . . . 28
Hoffman & Schlyter Expires September 10, 2012 [Page 2]
Internet-Draft DNS-Based Authentication for TLS March 2012
Appendix C. Examples . . . . . . . . . . . . . . . . . . . . . . 30
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 31
Hoffman & Schlyter Expires September 10, 2012 [Page 3]
Internet-Draft DNS-Based Authentication for TLS March 2012
1. Introduction
1.1. Background of the Problem
Applications that communicate over the Internet often need to prevent
eavesdropping, tampering, or forgery of their communications. The
Transport Layer Security (TLS) protocol provides this kind of
communications privacy over the Internet, using encryption.
The security properties of encryption systems depend strongly on the
keys that they use. If secret keys are revealed, or if published
keys can be replaced by bogus keys, these systems provide little or
no security.
TLS uses certificates to bind keys and names. A certificate combines
a published key with other information such as the name of the
service that the key is used by, and this combination is digitally
signed by another key. Having a certificate for a key is only
helpful if you trust the other key that signed the certificate. If
that other key was itself revealed or substituted, then its signature
is worthless in proving anything about the first key.
On the Internet, this problem has been solved for years by entities
called "Certification Authorities" (CAs). CAs protect their secret
key vigorously, while supplying their public key to the software
vendors who build TLS clients. They then sign certificates, and
supply those to TLS servers. TLS client software uses a set of these
CA keys as "trust anchors" to validate the signatures on certificates
that the client receives from TLS servers. Client software typically
allows any CA to usefully sign any other certificate.
This solution has gradually broken down because some CAs have become
untrustworthy. A single trusted CA that betrays its trust, either
voluntarily or by providing less-than-vigorous protection for its
secrets and capabilities, can compromise any other certificate that
TLS uses by signing a replacement certificate that contains a bogus
key. Several real-world occurrances that have exploited such CAs for
subversion of major web sites (presumably to abet wiretapping and
large-scale fraud) have brought TLS's CA model into disrepute.
The DNS Security Extensions (DNSSEC) provides a similar model that
involves trusted keys signing the information for untrusted keys.
However, DNSSEC provides three significant improvements. Keys are
tied to names in the Domain Name System (DNS), rather than to
arbitrary identifying strings; this is more convenient for Internet
protocols. Signed keys for any domain are accessible online through
a straightforward query using the standard DNSSEC protocol, so there
is no problem distributing the signed keys. Most significantly, the
Hoffman & Schlyter Expires September 10, 2012 [Page 4]
Internet-Draft DNS-Based Authentication for TLS March 2012
keys associated with a domain name can only be signed by a key
associated with the parent of that domain name; for example, the keys
for "example.com" can only be signed by the keys for "com", and the
keys for "com" can only be signed by the DNS root. This prevents an
untrustworthy signer from compromising anyone's keys except those in
their own subdomains. Like TLS, DNSSEC relies on public keys that
come built into the DNSSEC client software, but these keys come only
from a single root domain rather than from a multiplicity of CAs.
1.2. Securing the Association with a Server's Certificate
A TLS client begins a connection by exchanging messages with a TLS
server. It looks up the server's name using the DNS to get Internet
Protocol (IP) address associated with the name. It then begins a
connection to a client-chosen port at that address, and sends an
initial message there. However, the client does not yet know whether
an adversary is intercepting and/or altering its communication before
it reaches the TLS server. It does not even know whether the real
TLS server associated with that domain name has ever received its
initial messages.
The first response from the server in TLS may contain a certificate.
In order for the TLS client to authenticate that it is talking to the
expected TLS server, the client must validate that this certificate
is associated with the domain name used by the client to get to the
server. Currently, the client must extract the domain name from the
certificate and must successfully validate the certificate, including
chaining to a trust anchor.
There is a different way to authenticate the association of the
server's certificate with the intended domain name without trusting
an external CA. Given that the DNS administrator for a domain name
is authorized to give identifying information about the zone, it
makes sense to allow that administrator to also make an authoritative
binding between the domain name and a certificate that might be used
by a host at that domain name. The easiest way to do this is to use
the DNS, securing the binding with DNSSEC.
There are many use cases for such functionality. [RFC6394] lists the
ones that the DNS RRtype in this document are meant to apply.
[RFC6394] also lists many requirements, most of which this document
is believed to meet. Section 5 covers the applicability of this
document to the use cases in detail.
This document applies to both TLS [RFC5246] and DTLS [RFC6347]. In
order to make the document more readable, it mostly only talks about
"TLS", but in all cases, it means "TLS or DTLS". This document only
relates to securely associating certificates for TLS and DTLS with
Hoffman & Schlyter Expires September 10, 2012 [Page 5]
Internet-Draft DNS-Based Authentication for TLS March 2012
host names; other security protocols and other forms of
identification of TLS servers (such as IP addresses) are handled in
other documents. For example, keys for IPsec are covered in
[RFC4025] and keys for SSH are covered in [RFC4255].
1.3. Method For Securing Certificate Associations
A certificate association is formed from a piece of information
identifying a certificate (such as the contents of the certificate or
a trust anchor to which the certificate chains) and the domain name
where the data is found. This document only applies to PKIX
[RFC5280] certificates, not certificates of other formats.
A DNS query can return multiple certificate associations, such as in
the case of different server software on a single host using
different certificates, or in the case that a server is changing from
one certificate to another.
This document defines a secure method to associate the certificate
that is obtained from the TLS server with a domain name using DNS;
the DNS information needs to be be protected by DNSSEC. Because the
certificate association was retrieved based on a DNS query, the
domain name in the query is by definition associated with the
certificate.
DNSSEC, which is defined in RFCs 4033, 4034, and 4035 ([RFC4033],
[RFC4034], and [RFC4035]), uses cryptographic keys and digital
signatures to provide authentication of DNS data. Information that
is retrieved from the DNS and that is validated using DNSSEC is
thereby proved to be the authoritative data. The DNSSEC signature
MUST be validated on all responses that use DNSSEC in order to assure
the proof of origin of the data. This document does not specify how
DNSSEC validation occurs because there are many different proposals
for how a client might get validated DNSSEC results.
This document only relates to securely getting the DNS information
for the certificate association using DNSSEC; other secure DNS
mechanisms are out of scope.
1.4. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
This document also makes use of standard PKIX, DNSSEC, and TLS
terminology. See [RFC5280], [RFC4033], and [RFC5246] respectively,
for these terms. In addition, terms related to TLS-protected
Hoffman & Schlyter Expires September 10, 2012 [Page 6]
Internet-Draft DNS-Based Authentication for TLS March 2012
application services and DNS names are taken from [RFC6125].
2. The TLSA Resource Record
The TLSA DNS resource record (RR) is used to associate a certificate
with the domain name where the record is found. The semantics of how
the TLSA RR is interpreted are given later in this document.
The type value for the TLSA RR type is TBD.
The TLSA RR is class independent.
The TLSA RR has no special TTL requirements.
2.1. TLSA RDATA Wire Format
The RDATA for a TLSA RR consists of a one octet usage type field, a
one octet selector field, a one octet matching type field and the
certificate association data field.
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Usage | Selector | Matching Type | /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ /
/ /
/ Certificate Association Data /
/ /
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
2.1.1. The Certificate Usage Field
A one-octet value, called "certificate usage" or just "usage",
specifying the provided association that will be used to match the
target certificate from the TLS handshake. This value is defined in
a new IANA registry (see Section 7.2) in order to make it easier to
add additional certificate usages in the future. The usages defined
in this document are:
0 -- Certificate usage 0 is used to specify a CA certificate, or
the public key of such a certificate, that must be found in any of
the PKIX certification paths for the end entity certificate given
by the server in TLS. This usage is sometimes referred to as "CA
constraint" because it limits which CA can be used to issue
certificates for a given service on a host. The target
certificate MUST pass PKIX certification path validation and a CA
certificate that matches the TLSA record MUST be included as part
Hoffman & Schlyter Expires September 10, 2012 [Page 7]
Internet-Draft DNS-Based Authentication for TLS March 2012
of a valid certification path.
1 -- Certificate usage 1 is used to specify an end entity
certificate, or the public key of such a certificate, that must be
matched with the end entity certificate given by the server in
TLS. This usage is sometimes referred to as "service certificate
constraint" because it limits which end entity certificate may be
used by a given service on a host. The target certificate MUST
pass PKIX certification path validation and MUST match the TLSA
record.
2 -- Certificate usage 2 is used to specify a certificate, or the
public key of such a certificate, that must be used as the trust
anchor when validating the end entity certificate given by the
server in TLS. This usage is sometimes referred to as "trust
anchor assertion" and allows a domain name administrator to
specify a new trust anchor, for example if the domain issues its
own certificates under its own CA that is not expected to be in
the end users' collection of trust anchors. The target
certificate MUST pass PKIX certification path validation, with any
certificate matching the TLSA record considered to be a trust
anchor for this certification path validation.
3 -- Certificate usage 3 is used to specify a certificate, or the
public key of such a certificate, that must match the end entity
certificate given by the server in TLS. This usage is sometimes
referred to as "domain-issued certificate" because it allows for a
domain name administrator to issue certificates for a domain
without involving a third-party CA. The target certificate MUST
match the TLSA record. The difference between certificate usage 1
and certificate usage 3 is that certificate usage 1 requires that
the certificate pass PKIX validation, but PKIX validation is not
tested for certificate usage 3.
The certificate usages defined in this document explicitly only apply
to PKIX-formatted certificates in DER encoding. If TLS allows other
formats later, or if extensions to this RRtype are made that accept
other formats for certificates, those certificates will need their
own certificate usage values.
2.1.2. The Selector Field
A one-octet value, called "selector", specifying which part of the
TLS certificate presented by the server will be matched against the
association data. This value is defined in a new IANA registry (see
Section 7.3. The selectors defined in this document are:
Hoffman & Schlyter Expires September 10, 2012 [Page 8]
Internet-Draft DNS-Based Authentication for TLS March 2012
0 -- Full certificate
1 -- SubjectPublicKeyInfo
2.1.3. The Matching Type Field
A one-octet value, called "matching type", specifying how the
certificate association is presented. This value is defined in a new
IANA registry (see Section 7.4). The types defined in this document
are:
0 -- Exact match on selected content
1 -- SHA-256 hash of selected content [RFC6234]
2 -- SHA-512 hash of selected content [RFC6234]
If the TLSA record's matching type is a hash, the record SHOULD use
the same hash algorithm that was used in the signature in the
certificate. This will assist clients that support a small number of
hash algorithms.
2.1.4. The Certificate Association Data Field
The "certificate association data" to be matched. This field
contains the data to be matched. These bytes are either raw data
(that is, the full certificate or its SubjectPublicKeyInfo, depending
on the selector) for matching type 0, or the hash of the raw data for
matching types 1 and 2. The data refers to the certificate in the
association, not to the TLS ASN.1 Certificate object.
2.2. TLSA RR Presentation Format
The presentation format of the RDATA portion is as follows:
o The certificate usage field MUST be represented as an unsigned
decimal integer.
o The selector field MUST be represented as an unsigned decimal
integer.
o The matching type field MUST be represented as an unsigned decimal
integer.
o The certificate association data field MUST be represented as a
string of hexadecimal characters. Whitespace is allowed within
the string of hexadecimal characters.
Hoffman & Schlyter Expires September 10, 2012 [Page 9]
Internet-Draft DNS-Based Authentication for TLS March 2012
2.3. TLSA RR Examples
An example of a hashed (SHA-256) association of a PKIX CA
certificate:
_443._tcp.www.example.com. IN TLSA (
0 0 1 d2abde240d7cd3ee6b4b28c54df034b9
7983a1d16e8a410e4561cb106618e971 )
An example of a hashed (SHA-512) subject public key association of a
PKIX end entity certificate:
_443._tcp.www.example.com. IN TLSA (
1 1 2 92003ba34942dc74152e2f2c408d29ec
a5a520e7f2e06bb944f4dca346baf63c
1b177615d466f6c4b71c216a50292bd5
8c9ebdd2f74e38fe51ffd48c43326cbc )
An example of a full certificate association of a PKIX end entity
certificate:
_443._tcp.www.example.com. IN TLSA (
3 0 0 30820307308201efa003020102020... )
3. Domain Names for TLS Certificate Associations
Unless there is a protocol-specific specification that is different
than this one, TLSA resource records are stored at a prefixed DNS
domain name. The prefix is prepared in the following manner:
1. The decimal representation of the port number on which a TLS-
based service is assumed to exist is prepended with an underscore
character ("_") to become the left-most label in the prepared
domain name. This number has no leading zeros.
2. The protocol name of the transport on which a TLS-based service
is assumed to exist is prepended with an underscore character
("_") to become the second left-most label in the prepared domain
name. The transport names defined for this protocol are "tcp",
"udp" and "sctp".
3. The domain name is appended to the result of step 2 to complete
the prepared domain name.
For example, to request a TLSA resource record for an HTTP server
running TLS on port 443 at "www.example.com", you would use
"_443._tcp.www.example.com" in the request. To request a TLSA
Hoffman & Schlyter Expires September 10, 2012 [Page 10]
Internet-Draft DNS-Based Authentication for TLS March 2012
resource record for an SMTP server running the STARTTLS protocol on
port 25 at "mail.example.com", you would use
"_25._tcp.mail.example.com".
4. Use of TLSA Records in TLS
Section 2.1 of this document defines the mandatory matching rules for
the data from the TLSA certificate associations and the certificates
received from the TLS server.
The TLS session that is to be set up MUST be for the specific port
number and transport name that was given in the TLSA query.
Some specifications for applications that run under TLS, such as
[RFC2818] for HTTP, require the server's certificate to have a domain
name that matches the host name expected by the client. Some
specifications such as [RFC6125] detail how to match the identity
given in a PKIX certificate with those expected by the user.
An implementation of this protocol makes a DNS query for TLSA
records, validates these records using DNSSEC, and uses the resulting
TLSA records and validation status to modify its responses to the TLS
server.
If a host is using TLSA usage type 2 for its certifcate, the
corresponding TLS server SHOULD send the certificate that is
referenced just like it currently sends intermediate certificates.
Determining whether a TLSA RRset can be used depends on the DNSSEC
validation state (as defined in [RFC4033]).
o A TLSA RRset whose DNSSEC validation state is secure MUST be used
as a certificate association for TLS unless a local policy would
prohibit the use of the specific certificate association in the
secure TLSA RRset.
o If the DNSSEC validation state on the response to the request for
the TLSA RRset is bogus, this MUST cause TLS not to be started or,
if the TLS negotiation is already in progress, MUST cause the
connection to be aborted.
o A TLSA RRset whose DNSSEC validation state is indeterminate or
insecure cannot be used for TLS and MUST be considered unusable.
Clients which validate the DNSSEC signatures themselves MUST use
standard DNSSEC validation procedures. Clients that rely on another
entity to perform the DNSSEC signature validation MUST use a secure
Hoffman & Schlyter Expires September 10, 2012 [Page 11]
Internet-Draft DNS-Based Authentication for TLS March 2012
mechanism between themselves and the validator. Examples of secure
transports to other hosts include TSIG [RFC2845], SIG(0) [RFC2931],
and IPsec [RFC6071]. Note that it is not sufficient to use secure
transport to a DNS resolver that does not do DNSSEC signature
validation.
If a certificate association contains a certificate usage, selector,
or matching type that is not understood by the TLS client, that
certificate association MUST be considered unusable. If the
comparison data for a certificate is malformed, the certificate
association MUST be considered unusable.
If a certificate association contains a matching type or certificate
association data that uses a cryptographic algorithm that is
considered too weak for the TLS client's policy, the certificate
association MUST be marked as unusable.
If an application receives zero usable certificate associations, it
processes TLS in the normal fashion without any input from the TLSA
records. If an application receives one or more usable certificate
associations, it attempts to match each certificate association with
the TLS server's end entity certificate until a successful match is
found.
5. TLSA and DANE Use Cases and Requirements
The different types of certificate associations defined in TLSA are
matched with various sections of [RFC6394]. The use cases from
Section 3 of [RFC6394] are covered in this document as follows:
3.1 CA Constraints -- Implemented using certificate usage 0.
3.2 Certificate Constraints -- Implemented using certificate usage
1.
3.3 Trust Anchor Assertion and Domain-Issued Certificates --
Implemented using certificate usages 2 and 3, respectively.
The requirements from Section 4 of [RFC6394] are covered in this
document as follows:
Multiple Ports -- The TLSA records for different application
services running on a single host can be distinguished through the
service name and port number prefixed to the host name (see
Section 3).
Hoffman & Schlyter Expires September 10, 2012 [Page 12]
Internet-Draft DNS-Based Authentication for TLS March 2012
No Downgrade -- Section 4 specifies the conditions under which a
client can process and act upon TLSA records. Specifically, if
the DNSSEC status for the TLSA resource record set is determined
to be bogus, the TLS connection (if started) will fail.
Encapsulation -- Covered in the TLSA response semantics.
Predictability -- The appendixes of this specification provide
operational considerations and implementation guidance in order to
enable application developers to form a consistent interpretation
of the recommended DANE client behavior.
Opportunistic Security -- If a client conformant to this
specification can reliably determine the presence of a TLSA
record, it will attempt to use this information. Conversely, if a
client can reliably determine the absence of any TLSA record, it
will fall back to processing TLS in the normal fashion. This is
discussed in Section 4.
Combination -- Multiple TLSA records can be published for a given
host name, thus enabling the client to construct multiple TLSA
certificate associations that reflect different DANE assertions.
No support is provided to combine two TLSA certificate
associations in a single operation.
Roll-over -- TLSA records are processed in the normal manner within
the scope of DNS protocol, including the TTL expiration of the
records. This ensures that clients will not latch onto assertions
made by expired TLSA records, and will be able to transition from
using one DANE public key or certificate usage type to another.
Simple Key Management -- The SubjectPublicKeyInfo selector in the
TLSA record provides a mode that enables a domain holder to only
have to maintain a single long-lived public/private key pair
without the need to manage certificates. Appendix A outlines the
usefulness and the potential downsides to using this mode.
Minimal Dependencies -- This specification relies on DNSSEC to
protect the origin authenticity and integrity of the TLSA resource
record set. Additionally, if DNSSEC validation is not performed
on the system that wishes to use TLSA certificate bindings, this
specification requires that the "last mile" be over a secure
transport. There are no other deployment dependencies for this
approach.
Hoffman & Schlyter Expires September 10, 2012 [Page 13]
Internet-Draft DNS-Based Authentication for TLS March 2012
Minimal Options -- The operating modes map precisely to the DANE use
cases and requirements. DNSSEC use is mandatory in that this
specification encourages applications to use TLSA records that are
only shown to be validated.
Wild Cards -- Covered in a limited manner in the TLSA request
syntax; see Appendix A.
Redirection -- Covered in the TLSA request syntax; see Appendix A.
6. Mandatory-to-Implement Features
TLS clients conforming to this specification MUST be able to
correctly interpret TLSA records with certificate usages 0, 1, 2, and
3. TLS clients conforming to this specification MUST be able to
compare a certificate association with a certificate from the TLS
handshake using selectors type 0 and 1, and matching type 0 (no hash
used) and matching type 1 (SHA-256), and SHOULD be able to make such
comparisons with matching type 2 (SHA-512).
At the time this is written, it is expected that there will be a new
family of hash algorithms called SHA-3 within the next few years. It
is expected that some of the SHA-3 algorithms will be mandatory
and/or recommended for TLSA records after the algorithms are fully
defined. At that time, this specification will be updated.
7. IANA Considerations
In the following sections, "RFC Required" was chosen for TLSA usages
and "Specification Required" for selectors and matching types because
of the amount of detail that is likely to be needed for implementers
to correctly implement new usages as compared to new selectors and
matching types.
7.1. TLSA RRtype
This document uses a new DNS RR type, TLSA, whose value is TBD. A
separate request for the RR type will be submitted to the expert
reviewer, and future versions of this document will have that value
instead of TBD.
7.2. TLSA Usages
This document creates a new registry, "Certificate Usages for TLSA
Resource Records". The registry policy is "RFC Required". The
initial entries in the registry are:
Hoffman & Schlyter Expires September 10, 2012 [Page 14]
Internet-Draft DNS-Based Authentication for TLS March 2012
Value Short description Reference
----------------------------------------------------------
0 CA constraint [This]
1 Service certificate constraint [This]
2 Trust anchor assertion [This]
3 Domain-issued certificate [This]
4-254 Unassigned
255 Private use
Applications to the registry can request specific values that have
yet to be assigned.
7.3. TLSA Selectors
This document creates a new registry, "Selectors for TLSA Resource
Records". The registry policy is "Specification Required". The
initial entries in the registry are:
Value Short description Reference
----------------------------------------------------------
0 Full Certificate [This]
1 SubjectPublicKeyInfo [This]
2-254 Unassigned
255 Private use
Applications to the registry can request specific values that have
yet to be assigned.
7.4. TLSA Matching Types
This document creates a new registry, "Matching Types for TLSA
Resource Records". The registry policy is "Specification Required".
The initial entries in the registry are:
Value Short description Reference
--------------------------------------------------------
0 No hash used [This]
1 SHA-256 RFC 6234
2 SHA-512 RFC 6234
3-254 Unassigned
255 Private use
Applications to the registry can request specific values that have
yet to be assigned.
Hoffman & Schlyter Expires September 10, 2012 [Page 15]
Internet-Draft DNS-Based Authentication for TLS March 2012
8. Security Considerations
The security of the DNS RRtype described in this document relies on
the security of DNSSEC as used by the client requesting A/AAAA and
TLSA records.
A DNS administrator who goes rogue and changes both the A/AAAA and
TLSA records for a domain name can cause the user to go to an
unauthorized server that will appear authorized, unless the client
performs PKIX certification path validation and rejects the
certificate. That administrator could probably get a certificate
issued anyway, so this is not an additional threat.
If the authentication mechanism for adding or changing TLSA data in a
zone is weaker than the authentication mechanism for changing the
A/AAAA records, a man-in-the-middle who can redirect traffic to their
site may be able to impersonate the attacked host in TLS if they can
use the weaker authentication mechanism. A better design for
authenticating DNS would be to have the same level of authentication
used for all DNS additions and changes for a particular domain name.
SSL proxies can sometimes act as a man-in-the-middle for TLS clients.
In these scenarios, the clients add a new trust anchor whose private
key is kept on the SSL proxy; the proxy intercepts TLS requests,
creates a new TLS session with the intended host, and sets up a TLS
session with the client using a certificate that chains to the trust
anchor installed in the client by the proxy. In such environments,
using TLSA records will prevent the SSL proxy from functioning as
expected because the TLS client will get a certificate association
from the DNS that will not match the certificate that the SSL proxy
uses with the client. The client, seeing the proxy's new certificate
for the supposed destination will not set up a TLS session.
Client treatment of any information included in the certificate trust
anchor is a matter of local policy. This specification does not
mandate that such information be inspected or validated by the
server's domain name administrator.
If a server's certificate is revoked, or if an intermediate CA in a
chain between the end entity and a trust anchor has its certificate
revoked, a TLSA record with a certificate type of 2 that matches the
revoked certificate would in essence override the revocation because
the client would treat that revoked certificate as a trust anchor and
thus not check its revocation status. Because of this, domain
administrators need to be responsible for being sure that the key or
certificate used in TLSA records with a certificate type of 2 are in
fact able to be used as reliable trust anchors.
Hoffman & Schlyter Expires September 10, 2012 [Page 16]
Internet-Draft DNS-Based Authentication for TLS March 2012
Certificates that are delivered in TLSA with usage type 2
fundamentally change the way the TLS server's end entity certificate
is evaluated. For example, the server's certificate might chain to
an existing CA through an intermediate CA that has certain policy
restrictions, and the certificate would not pass those restrictions
and thus normally be rejected. That intermediate CA could issue
itself a new certificate without the policy restrictions and tell its
customers to use that certificate with usage type 2. This in essence
allows an intermediate CA to be come a trust anchor for certificates
that the end user might have expected to chain to an existing trust
anchor.
If an administrator wishes to stop using a TLSA record, the
administrator can simply remove it from the DNS. Normal clients will
stop using the TLSA record after the TTL has expired. Replay attacks
against the TLSA record are not possible after the expiration date on
the RRsig of the TLSA record that was removed.
The client's full trust of a certificate retrieved from a TLSA record
with a certificate usage type of 2 or 3 may be a matter of local
policy. While such trust is limited to the specific domain nane for
which the TLSA query was made, local policy may deny the trust or
further restrict the conditions under which that trust is permitted.
8.1. DNS Caching
Implementations of this protocol rely heavily on the DNS, and are
thus prone to security attacks based on the deliberate mis-
association of TLSA records and DNS names. Implementations need to
be cautious in assuming the continuing validity of an assocation
between a TLSA record and a DNS name.
In particular, implementations SHOULD rely on their DNS resolver for
confirmation of an association between a TLSA record and a DNS name,
rather than caching the result of previous domain name lookups. Many
platforms already can cache domain name lookups locally when
appropriate, and they SHOULD be configured to do so. It is proper
for these lookups to be cached, however, only when the TTL (Time To
Live) information reported by the DNS makes it likely that the cached
information will remain useful.
If implementations cache the results of domain name lookups in order
to achieve a performance improvement, they MUST observe the TTL
information reported by DNS. Implementations that fail to follow
this rule could be spoofed or have access denied when a previously-
accessed server's TLSA record changes, such as during a certificate
rollover.
Hoffman & Schlyter Expires September 10, 2012 [Page 17]
Internet-Draft DNS-Based Authentication for TLS March 2012
9. Acknowledgements
Many of the ideas in this document have been discussed over many
years. More recently, the ideas have been discussed by the authors
and others in a more focused fashion. In particular, some of the
ideas and words here originated with Paul Vixie, Dan Kaminsky, Jeff
Hodges, Phill Hallam-Baker, Simon Josefsson, Warren Kumari, Adam
Langley, Ben Laurie, Ilari Liusvaara, Ondrej Mikle, Scott Schmit,
Ondrej Sury, Richard Barnes, Jim Schaad, Stephen Farrell, Suresh
Krishnaswamy, Peter Palfrader, Pieter Lexis, Wouter Wijngaards and
John Gilmore.
This document has also been greatly helped by many active
participants of the DANE Working Group.
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4033] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "DNS Security Introduction and Requirements",
RFC 4033, March 2005.
[RFC4034] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "Resource Records for the DNS Security Extensions",
RFC 4034, March 2005.
[RFC4035] Arends, R., Austein, R., Larson, M., Massey, D., and S.
Rose, "Protocol Modifications for the DNS Security
Extensions", RFC 4035, March 2005.
[RFC5246] Dierks, T. and E. Rescorla, "The Transport Layer Security
(TLS) Protocol Version 1.2", RFC 5246, August 2008.
[RFC5280] Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
Housley, R., and W. Polk, "Internet X.509 Public Key
Infrastructure Certificate and Certificate Revocation List
(CRL) Profile", RFC 5280, May 2008.
[RFC6125] Saint-Andre, P. and J. Hodges, "Representation and
Verification of Domain-Based Application Service Identity
within Internet Public Key Infrastructure Using X.509
(PKIX) Certificates in the Context of Transport Layer
Security (TLS)", RFC 6125, March 2011.
Hoffman & Schlyter Expires September 10, 2012 [Page 18]
Internet-Draft DNS-Based Authentication for TLS March 2012
[RFC6347] Rescorla, E. and N. Modadugu, "Datagram Transport Layer
Security Version 1.2", RFC 6347, January 2012.
10.2. Informative References
[RFC2782] Gulbrandsen, A., Vixie, P., and L. Esibov, "A DNS RR for
specifying the location of services (DNS SRV)", RFC 2782,
February 2000.
[RFC2818] Rescorla, E., "HTTP Over TLS", RFC 2818, May 2000.
[RFC2845] Vixie, P., Gudmundsson, O., Eastlake, D., and B.
Wellington, "Secret Key Transaction Authentication for DNS
(TSIG)", RFC 2845, May 2000.
[RFC2931] Eastlake, D., "DNS Request and Transaction Signatures (
SIG(0)s)", RFC 2931, September 2000.
[RFC4025] Richardson, M., "A Method for Storing IPsec Keying
Material in DNS", RFC 4025, March 2005.
[RFC4255] Schlyter, J. and W. Griffin, "Using DNS to Securely
Publish Secure Shell (SSH) Key Fingerprints", RFC 4255,
January 2006.
[RFC4641] Kolkman, O. and R. Gieben, "DNSSEC Operational Practices",
RFC 4641, September 2006.
[RFC6066] Eastlake, D., "Transport Layer Security (TLS) Extensions:
Extension Definitions", RFC 6066, January 2011.
[RFC6071] Frankel, S. and S. Krishnan, "IP Security (IPsec) and
Internet Key Exchange (IKE) Document Roadmap", RFC 6071,
February 2011.
[RFC6234] Eastlake, D. and T. Hansen, "US Secure Hash Algorithms
(SHA and SHA-based HMAC and HKDF)", RFC 6234, May 2011.
[RFC6394] Barnes, R., "Use Cases and Requirements for DNS-Based
Authentication of Named Entities (DANE)", RFC 6394,
October 2011.
Appendix A. Operational Considerations for Deploying TLSA Records
Hoffman & Schlyter Expires September 10, 2012 [Page 19]
Internet-Draft DNS-Based Authentication for TLS March 2012
A.1. Creating TLSA Records
When creating TLSA records care must be taken to avoid
misconfigurations. Section 4 of this document states that a TLSA
RRset whose validation state is secure MUST be used. This means that
the existence of such a RRset effectively disables other forms of
name and path validation. A misconfigured TLSA RRset will
effectively disable access to the TLS server for all conforming
clients, and this document does not provide any means of making a
gradual transition to using TLSA.
When creating TLSA records with certificate usage type 0 (CA
Certificate) or type 2 (Trust Anchor), one needs to understand the
implications when choosing between selector type 0 (full certificate)
and 1 (SubjectPublicKeyInfo). A careful choice is required because
different methods for building trust chains are used by different TLS
clients. The following outlines the cases that one should be aware
of and discusses the implications of the choice of selector type.
Certificate usage 2 is not affected by the different types of chain
building when the end entity certificate is the same as the trust
anchor certificate.
A.1.1. Ambiguities and Corner Cases When TLS Clients Build Trust Chains
TLS clients may implement their own chain-building code rather than
rely on the chain presented by the TLS server. This means that,
except for the end entity certificate, any certificate presented in
the suggested chain might or might not be present in the final chain
built by the client.
Certificates that the client can use to replace certificates from
original chain include:
o Client's trust anchors
o Certificates cached locally
o Certificates retrieved from a URI listed in an Authority
Information Access X.509v3 extension
CAs frequently reissue certificates with different validity period,
signature algorithm (such as an different hash algorithm in the
signature algorithm), CA key pair (such as for a cross-certificate),
or PKIX extensions where the public key and subject remain the same.
These reissued certificates are the certificates TLS client can use
in place of an original certificate.
Hoffman & Schlyter Expires September 10, 2012 [Page 20]
Internet-Draft DNS-Based Authentication for TLS March 2012
Clients are known to exchange or remove certificates that could cause
TLSA association that rely on the full certificate to fail. For
example:
o The client considers the signature algorithm of a certificate to
no longer be sufficiently secure
o The client might not have an associated root certificate in its
trust store and instead uses a cross-certificate with an identical
subject and public key.
A.1.2. Choosing a Selector Type
In this section, "false-negative failure" means that a client will
not accept the TLSA association for certificate designated by DNS
administrator. Also, "false-positive acceptance" means that the
client accepts a TLSA association for a certificate that is not
designated by the DNS administrator.
A.1.2.1. Selector Type 0 (Full Certificate)
The "Full certificate" selector provides the most precise
specification of a TLS certificate association, capturing all fields
of the PKIX certificate. For a DNS administrator, the best course to
avoid false-negative failures in the client when using this selector
are:
o If a CA issued a replacement certificate, don't associate to CA
certificates that have a signature algorithm with a hash that is
considered weak (such as MD2 and MD5).
o Determine how common client applications process the TLSA
association using a fresh client installation, that is, with the
local certificate cache empty.
A.1.2.2. Selector Type 1 (SubjectPublicKeyInfo)
A SubjectPublicKeyInfo selector gives greater flexibility in avoiding
some false-negative failures caused by trust-chain-building
algorithms used in clients.
One specific use-case should be noted: creating a TLSA association to
CA certificate I1 that directly signed end entity certificate S1 of
the server. The case can be illustrated by following graph:
Hoffman & Schlyter Expires September 10, 2012 [Page 21]
Internet-Draft DNS-Based Authentication for TLS March 2012
+----+ +----+
| I1 | | I2 |
+----+ +----+
| |
v v
+----+ +----+
| S1 | | S1 |
+----+ +----+
Certificate chain sent by A different validation path
server in TLS handshake built by the TLS client
I2 is a reissued version of CA certificate I1 (that is, it has a
different hash in its signature algorithm).
In the above scenario, both certificates I1 and I2 that sign S1 need
to have identical SubjectPublicKeyInfos because the key used to sign
S1 is fixed. An association to SubjectPublicKeyInfo (selector type
1) will always succeed in such a case, but an association with a full
certificate (selector type 0) might not work due to a false-negative
failure.
The attack surface is a bit broader compared to "full certificate"
selector: the DNS administrator might unintentionally specify an
association that would lead to false-positive acceptance.
o The administrator must know or trust that the CA does not engage
in bad practices, such as not sharing key of I1 for unrelated CA
certificates leading to trust-chain redirect. If possible, the
administrator should review all CA certificates that have the same
SPKI.
o The administrator should understand whether some PKIX extension
may adversely affect security of the association. If possible,
administrators should review all CA certificates that share the
SubjectPublicKeyInfo.
o The administrator should understand that any CA could, in the
future, issue a certificate that contains the same
SubjectPublicKeyInfo. Therefore, new chains can crop up in the
future without any warning.
Using the SubjectPublicKeyInfo selector for association with a
certificate in a chain above I1 needs to be decided on a case-by-case
basis: there are too many possibilities based on the issuing CA's
practices. Unless the full implications of such an association are
understood by the administrator, using selector type 0 is a better
option from a security perspective.
Hoffman & Schlyter Expires September 10, 2012 [Page 22]
Internet-Draft DNS-Based Authentication for TLS March 2012
A.2. Provisioning TLSA Records in DNS
A.2.1. Provisioning TLSA Records with Aliases
The TLSA resource record is not special in the DNS; it acts exactly
like any other RRtype where the queried name has one or more labels
prefixed to the base name, such as the SRV RRtype [RFC2782]. This
affects the way that the TLSA resource record is used when aliasing
in the DNS.
Note that the IETF sometimes adds new types of aliasing in the DNS.
If that happens in the future, those aliases might affect TLSA
records, hopefully in a good way.
A.2.1.1. Provisioning TLSA Records with CNAME Records
Using CNAME to alias in DNS only aliases from the exact name given,
not any zones below the given name. For example, assume that a zone
file has only the following:
sub1.example.com. IN CNAME sub2.example.com.
In this case, a request for the A record at "bottom.sub1.example.com"
would not return any records because the CNAME given only aliases the
name given. Assume, instead, the zone file has the following:
sub3.example.com. IN CNAME sub4.example.com.
bottom.sub3.example.com. IN CNAME bottom.sub4.example.com.
In this case, a request for the A record at bottom.sub3.example.com
would in fact return whatever value for the A record exists at
bottom.sub4.example.com.
Application implementations and full-service resolvers request DNS
records using libraries that automatically follow CNAME (and DNAME)
aliasing. This allows hosts to put TLSA records in their own zones
or to use CNAME to do redirection.
If the owner of the original domain wants a TLSA record for the same,
they simply enter it under the defined prefix:
; No TLSA record in target domain
;
sub5.example.com. IN CNAME sub6.example.com.
_443._tcp.sub5.example.com. IN TLSA 1 1 1 308202c5308201ab...
sub6.example.com. IN A 192.0.2.1
sub6.example.com. IN AAAA 2001:db8::1
Hoffman & Schlyter Expires September 10, 2012 [Page 23]
Internet-Draft DNS-Based Authentication for TLS March 2012
If the owner of the original domain wants to have the target domain
host the TLSA record, the original domain uses a CNAME record:
; TLSA record for original domain has CNAME to target domain
;
sub5.example.com. IN CNAME sub6.example.com.
_443._tcp.sub5.example.com. IN CNAME _443._tcp.sub6.example.com.
sub6.example.com. IN A 192.0.2.1
sub6.example.com. IN AAAA 2001:db8::1
_443._tcp.sub6.example.com. IN TLSA 1 1 1 536a570ac49d9ba4...
Note that it is acceptable for both the original domain and the
target domain to have TLSA records, but the two records are
unrelated. Consider the following:
; TLSA record in both the original and target domain
;
sub5.example.com. IN CNAME sub6.example.com.
_443._tcp.sub5.example.com. IN TLSA 1 1 1 308202c5308201ab...
sub6.example.com. IN A 192.0.2.1
sub6.example.com. IN AAAA 2001:db8::1
_443._tcp.sub6.example.com. IN TLSA 1 1 1 ac49d9ba4570ac49...
In this example, someone looking for the TLSA record for
sub5.example.com would always get the record whose value starts
"308202c5308201ab"; the TLSA record whose value starts
"ac49d9ba4570ac49" would only be sought by someone who is looking for
the TLSA record for sub6.example.com, and never for sub5.example.com.
One should note that deploying different certificates for multiple
services located at a shared TLS listener often requires the use of
TLS SNI (Server Name Indication) [RFC6066].
Note that these methods use the normal method for DNS aliasing using
CNAME: the DNS client requests the record type that they actually
want.
A.2.1.2. Provisioning TLSA Records with DNAME Records
Using DNAME records allows a zone owner to alias an entire subtree of
names below the name that has the DNAME. This allows the wholesale
aliasing of prefixed records such as those used by TLSA, SRV, and so
on without aliasing the name itself. However, because DNAME can only
be used for subtrees of a base name, it is rarely used to alias
individual hosts that might also be running TLS.
Hoffman & Schlyter Expires September 10, 2012 [Page 24]
Internet-Draft DNS-Based Authentication for TLS March 2012
; TLSA record in target domain, visible in original domain via DNAME
;
sub5.example.com. IN CNAME sub6.example.com.
_tcp.sub5.example.com. IN DNAME _tcp.sub6.example.com.
sub6.example.com. IN A 192.0.2.1
sub6.example.com. IN AAAA 2001:db8::1
_443._tcp.sub6.example.com. IN TLSA 1 1 1 536a570ac49d9ba4...
A.2.1.3. Provisioning TLSA Records with Wildcards
Wildcards are generally not terribly useful for RRtypes that require
prefixing because you can only wildcard at a layer below the host
name. For example, if you want to have the same TLSA record for
every TCP port for www.example.com, you might have
*._tcp.www.example.com. IN TLSA 1 1 1 5c1502a6549c423b...
This is possibly useful in some scenarios where the same service is
offered on many ports.
A.3. Securing the Last Hop
As described in Section 4, an application processing TLSA records
must know the DNSSEC validity of those records. There are many ways
for the application to securely find this out, and this specification
does not mandate any single method.
Some common methods for an application to know the DNSSEC validity of
TLSA records include:
o The application can have its own DNS resolver and DNSSEC
validation stack.
o The application can communicate through a trusted channel (such as
requests to the operating system under which the application is
running) to a local DNS resolver that does DNSSEC validation.
o The application can communicate through a secured channel (such as
requests running over TLS, IPsec, TSIG or SIG(0)) to a non-local
DNS resolver that does DNSSEC validation.
o The application can communicate through a secured channel (such as
requests running over TLS, IPsec, TSIG or SIG(0)) to a non-local
DNS resolver that does not do DNSSEC validation, but gets
responses through a secured channel from a different DNS resolver
that does DNSSEC validation.
Hoffman & Schlyter Expires September 10, 2012 [Page 25]
Internet-Draft DNS-Based Authentication for TLS March 2012
A.4. Handling Certificate Rollover
Certificate rollover is handled in much the same was as for rolling
DNSSEC zone signing keys using the pre-publish key rollover method
[RFC4641]. Suppose example.com has a single TLSA record for a TLS
service on TCP port 990:
_990._tcp.example.com IN TLSA 1 1 1 1CFC98A706BCF3683015...
To start the rollover process, obtain or generate the new certificate
or SubjectPublicKeyInfo to be used after the rollover and generate
the new TLSA record. Add that record alongside the old one:
_990._tcp.example.com IN TLSA 1 1 1 1CFC98A706BCF3683015...
_990._tcp.example.com IN TLSA 1 1 1 62D5414CD1CC657E3D30...
After the new records have propagated to the authoritative
nameservers and the TTL of the old record has expired, switch to the
new certificate on the TLS server. Once this has occurred, the old
TLSA record can be removed:
_990._tcp.example.com IN TLSA 1 1 1 62D5414CD1CC657E3D30...
This completes the certificate rollover.
Appendix B. Pseudocode for Using TLSA
This appendix describes the interactions given earlier in this
specification in pseudocode format. This appendix is non-normative.
If the steps below disagree with the text earlier in the document,
the steps earlier in the document should be considered correct and
this text incorrect.
Note that this pseudocode is more strict than the normative text.
For instance, it forces an order on the evaluation of criteria which
is not mandatory from the normative text.
B.1. Helper Functions
// implement the function for exiting
function Finish (F) = {
if (F == ABORT_TLS) {
abort the TLS handshake or prevent TLS from starting
exit
}
Hoffman & Schlyter Expires September 10, 2012 [Page 26]
Internet-Draft DNS-Based Authentication for TLS March 2012
if (F == NO_TLSA) {
fall back to non-TLSA certificate validation
exit
}
if (F == ACCEPT) {
accept the TLS connection
exit
}
// unreachable
}
// implement the selector function
function Select (S, X) = {
// Full certificate
if (S == 0) {
return X in DER encoding
}
// SubjectPublicKeyInfo
if (S == 1) {
return X.SubjectPublicKeyInfo in DER encoding
}
// unreachable
}
// implement the matching function
function Match (M, X, Y) {
// Exact match on selected content
if (M == 0) {
return (X == Y)
}
// SHA-256 hash of selected content
if (M == 1) {
return (SHA-256(X) == Y)
}
// SHA-512 hash of selected content
if (M == 2) {
return (SHA-512(X) == Y)
}
// unreachable
}
Hoffman & Schlyter Expires September 10, 2012 [Page 27]
Internet-Draft DNS-Based Authentication for TLS March 2012
B.2. Main TLSA Pseudo Code
TLS connect using [transport] to [name] on [port] and receiving end
entity cert C for the TLS server:
(TLSArecords, ValState) = DNSSECValidatedLookup(
domainname=_[port]._[transport].[name], RRtype=TLSA)
// check for states that would change processing
if (ValState == BOGUS) {
Finish(ABORT_TLS)
}
if ((ValState == INDETERMINATE) or (ValState == INSECURE)) {
Finish(NO_TLSA)
}
// if here, ValState must be SECURE
for each R in TLSArecords {
// unusable records include unknown certUsage, unknown
// selectorType, unknown matchingType, erroneous RDATA, and
// prohibited by local policy
if (R is unusable) {
remove R from TLSArecords
}
}
if (length(TLSArecords) == 0) {
Finish(NO_TLSA)
}
// A TLS client might have multiple trust anchors that it might use
// when validating the TLS server's end entity certificate. Also,
// there can be multiple PKIX certification paths for the
// certificates given by the server in TLS. Thus, there are
// possibly many chains that might need to be tested during
// PKIX path validation.
for each R in TLSArecords {
// pass PKIX certificate validation and chain through a CA cert
// that comes from TLSA
if (R.certUsage == 0) {
for each PKIX certification path H {
if (C passes PKIX certification path validation in H) {
for each D in H {
if ((D is a CA certificate) and
Match(R.matchingType, Select(R.selectorType, D),
R.cert)) {
Hoffman & Schlyter Expires September 10, 2012 [Page 28]
Internet-Draft DNS-Based Authentication for TLS March 2012
Finish(ACCEPT)
}
}
}
}
}
// pass PKIX certificate validation and match EE cert from TLSA
if (R.certUsage == 1) {
for each PKIX certification path H {
if ((C passes PKIX certificate validation in H) and
Match(R.matchingType, Select(R.selectorType, C),
R.cert)) {
Finish(ACCEPT)
}
}
}
// pass PKIX certification validation using TLSA record as the
// trust anchor
if (R.certUsage == 2) {
for each PKIX certification path H that has R as the
trust anchor {
if (C passes PKIX certification validation in H) and
Match(R.matchingType, Select(R.selectorType, C),
R.cert)) {
Finish(ACCEPT)
}
}
}
// match the TLSA record and the TLS certificate
if (R.certUsage == 3) {
if Match(R.matchingType, Select(R.selectorType, C), R.cert)
Finish(ACCEPT)
}
}
}
// if here, then none of the TLSA records ended in "Finish(ACCEPT)"
// so abort TLS
Finish(ABORT_TLS)
Hoffman & Schlyter Expires September 10, 2012 [Page 29]
Internet-Draft DNS-Based Authentication for TLS March 2012
Appendix C. Examples
The following are examples of self-signed certificates that have been
been generated with various selectors and matching types. They were
generated with one piece of software, and validated by an individual
using other tools.
S = Selector
M = Matching Type
S M Association Data
0 0 30820454308202BC020900AB58D24E77AD2AF6300D06092A86
4886F70D0101050500306C310B3009060355040613024E4C31163014
0603550408130D4E6F6F72642D486F6C6C616E643112301006035504
071309416D7374657264616D310C300A060355040A13034F53333123
30210603550403131A64616E652E6B6965762E70726163746963756D
2E6F73332E6E6C301E170D3132303131363136353730335A170D3232
303131333136353730335A306C310B3009060355040613024E4C3116
30140603550408130D4E6F6F72642D486F6C6C616E64311230100603
5504071309416D7374657264616D310C300A060355040A13034F5333
312330210603550403131A64616E652E6B6965762E70726163746963
756D2E6F73332E6E6C308201A2300D06092A864886F70D0101010500
0382018F003082018A0282018100E62C84A5AFE59F0A2A6B250DEE68
7AC8C5C604F57D26CEB2119140FFAC38C4B9CBBE8923082E7F81626B
6AD5DEA0C8771C74E3CAA7F613054AEFA3673E48FFE47B3F7AF987DE
281A68230B24B9DA1A98DCBE51195B60E42FD7517C328D983E26A827
C877AB914EE4C1BFDEAD48BD25BE5F2C473BA9C1CBBDDDA0C374D0D5
8C389CC3D6D8C20662E19CF768F32441B7F7D14AEA8966CE7C32A172
2AB38623D008029A9E4702883F8B977A1A1E5292BF8AD72239D40393
37B86A3AC60FA001290452177BF1798609A05A130F033457A5212629
FBDDB8E70E2A9E6556873C4F7CA46AE4A8B178F05FB319005E1C1C7D
4BD77DFA34035563C126AA2C3328B900E7990AC9787F01DA82F74C3D
4B6674CCECE1FD4C6EF9E6644F4635EDEDA39D8B0E2F7C8E06DAE775
6213BD3D60831175BE290442B4AFC5AE6F46B769855A067C1097E617
962529E166F22AEE10DDB981B8CD6FF17D3D70723169038DBFBC1A44
9C8D0D31BC683C5F3CE26148E42EC9BBD4D9F261569B25B53C1D7FC2
DDFF6B4CAC050203010001300D06092A864886F70D01010505000382
0181002B2ABE063E9C86AC4A1F7835372091079C8276A9C2C5D1EC57
64DE523FDDABDEAB3FD34E6FE6CBA054580A6785A663595D90132B93
D473929E81FA0887D2FFF78A81C7D014B97778AB6AC9E5E690F6F5A9
E92BB5FBAB71B857AE69B6E18BDCCB0BA6FCD9D4B084A34F3635148C
495D48FE635903B888EC1DEB2610548EDD48D63F86513A4562469831
48C0D5DB82D73A4C350A42BB661D763430FC6C8E5F9D13EA1B76AA52
A4C358E5EA04000F794618303AB6CEEA4E9A8E9C74D73C1B0B7BAF16
DEDE7696B5E2F206F777100F5727E1684D4132F5E692F47AF6756EA8
B421000BE031B5D8F0220E436B51FB154FE9595333C13A2403F9DE08
E5DDC5A22FD6182E339593E26374450220BC14F3E40FF33F084526B0
Hoffman & Schlyter Expires September 10, 2012 [Page 30]
Internet-Draft DNS-Based Authentication for TLS March 2012
9C34250702E8A352B332CCCB0F9DE2CF2B338823B92AFC61C0B6B8AB
DB5AF718ED8DDA97C298E46B82A01B14814868CFA4F2C36268BFFF4A
591F42658BF75918902D3E426DFE1D5FF0FC6A212071F6DA8BD833FE
2E560D87775E8EE9333C05B6FB8EB56589D910DB5EA903
0 1 EFDDF0D915C7BDC5782C0881E1B2A95AD099FBDD06D7B1F779
82D9364338D955
0 2 81EE7F6C0ECC6B09B7785A9418F54432DE630DD54DC6EE9E3C
49DE547708D236D4C413C3E97E44F969E635958AA410495844127C04
883503E5B024CF7A8F6A94
1 0 308201A2300D06092A864886F70D01010105000382018F0030
82018A0282018100E62C84A5AFE59F0A2A6B250DEE687AC8C5C604F5
7D26CEB2119140FFAC38C4B9CBBE8923082E7F81626B6AD5DEA0C877
1C74E3CAA7F613054AEFA3673E48FFE47B3F7AF987DE281A68230B24
B9DA1A98DCBE51195B60E42FD7517C328D983E26A827C877AB914EE4
C1BFDEAD48BD25BE5F2C473BA9C1CBBDDDA0C374D0D58C389CC3D6D8
C20662E19CF768F32441B7F7D14AEA8966CE7C32A1722AB38623D008
029A9E4702883F8B977A1A1E5292BF8AD72239D4039337B86A3AC60F
A001290452177BF1798609A05A130F033457A5212629FBDDB8E70E2A
9E6556873C4F7CA46AE4A8B178F05FB319005E1C1C7D4BD77DFA3403
5563C126AA2C3328B900E7990AC9787F01DA82F74C3D4B6674CCECE1
FD4C6EF9E6644F4635EDEDA39D8B0E2F7C8E06DAE7756213BD3D6083
1175BE290442B4AFC5AE6F46B769855A067C1097E617962529E166F2
2AEE10DDB981B8CD6FF17D3D70723169038DBFBC1A449C8D0D31BC68
3C5F3CE26148E42EC9BBD4D9F261569B25B53C1D7FC2DDFF6B4CAC05
0203010001
1 1 8755CDAA8FE24EF16CC0F2C918063185E433FAAF1415664911
D9E30A924138C4
1 2 D43165B4CDF8F8660AECCCC5344D9D9AE45FFD7E6AAB7AB9EE
C169B58E11F227ED90C17330CC17B5CCEF0390066008C720CEC6AAE5
33A934B3A2D7E232C94AB4
Authors' Addresses
Paul Hoffman
VPN Consortium
Email: paul.hoffman@vpnc.org
Hoffman & Schlyter Expires September 10, 2012 [Page 31]
Internet-Draft DNS-Based Authentication for TLS March 2012
Jakob Schlyter
Kirei AB
Email: jakob@kirei.se
Hoffman & Schlyter Expires September 10, 2012 [Page 32]