CCAMP Working Group H. Zheng
Internet-Draft I. Busi
Intended status: Standards Track Huawei Technologies
Expires: September 10, 2020 March 9, 2020
A YANG Data Model for Layer 1 Types
draft-ietf-ccamp-layer1-types-05
Abstract
This document defines a collection of common data types and groupings
in YANG data modeling language for layer 1 networks. These derived
common types and groupings are intended to be imported by modules
that specifies the OTN networks, including the topology, tunnel,
client signal adaptation and service.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on September 10, 2020.
Copyright Notice
Copyright (c) 2020 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Zheng & Busi Expires September 10, 2020 [Page 1]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2
2. Terminology and Notations . . . . . . . . . . . . . . . . . . 3
3. Prefix in Data Node Names . . . . . . . . . . . . . . . . . . 3
4. Layer 1 Types Overview . . . . . . . . . . . . . . . . . . . 3
4.1. Relationship with other Modules . . . . . . . . . . . . . 3
4.2. Content in Layer 1 Type Module . . . . . . . . . . . . . 3
4.3. OTN Label and Label Range . . . . . . . . . . . . . . . . 5
4.4. ODUflex . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.4.1. Resizable ODUflex . . . . . . . . . . . . . . . . . . 8
5. YANG Code for Layer1 Types . . . . . . . . . . . . . . . . . 9
6. Security Considerations . . . . . . . . . . . . . . . . . . . 27
7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 28
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 28
9. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 28
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 30
10.1. Normative References . . . . . . . . . . . . . . . . . . 30
10.2. Informative References . . . . . . . . . . . . . . . . . 31
Appendix A. Examples of OTN Label Ranges . . . . . . . . . . . . 32
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 38
1. Introduction
This document introduces a collection of common data types which
would be used in Layer 1 networks. The derived types and groupings
are designed to be the common types applicable for modeling Traffic
Engineering (TE) features for Layer 1 networks.
Typical Layer 1 network, the Optical Transport Networking, was
specified in [RFC7062]. Corresponding routing and signaling protocol
have been specified in [RFC7138] and [RFC7139]. The types and
groupings defined in this document is consistent to these document,
and will be imported in other Layer 1 data models, including but not
restrictive to, [I-D.ietf-ccamp-otn-topo-yang],
[I-D.ietf-ccamp-otn-tunnel-model],
[I-D.ietf-ccamp-client-signal-yang] and [I-D.ietf-ccamp-l1csm-yang].
The data model in this draft has only types defined including
groupings, typedef and identities. There is no need to include
configuration and state data according to the new Network Management
Datastore Architecture [RFC8342]. The content in this draft is in
consistent with other specifications, including [MEF63] for Layer 1
service attributes, [ITU-Tg709] and [ITU-Tgsup43] for OTN data plane
definitions.
Zheng & Busi Expires September 10, 2020 [Page 2]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
2. Terminology and Notations
Refer to [RFC7062] for the key terms used in this document, and the
terminology for describing YANG data models can be found in
[RFC7950].
3. Prefix in Data Node Names
In this document, names of data nodes and other data model objects
are prefixed using the standard prefix associated with the
corresponding YANG imported modules.
+-------------+---------------------------+----------------------+
| Prefix | YANG module | Reference |
+-------------+---------------------------+----------------------+
| l1-types | ietf-layer1-types | This Document |
+-------------+---------------------------+----------------------+
4. Layer 1 Types Overview
4.1. Relationship with other Modules
This document defines one YANG module for common Layer 1 types. The
objective is to specifies common Layer 1 TE types that can be
imported by layer 1 specific technology, for example OTN, in its
technology-specific modules such as topology and tunnels. It is
worth noting that the generic traffic-engineering (TE) types module
is specified in [I-D.ietf-teas-yang-te-types] as ietf-te-types, and
both the module ietf-te-types and ietf-layer1-types are needed to be
imported when the OTN is configured. Generic attributes such as te-
bandwidth and te-label, are indicated in ietf-te-types in
[I-D.ietf-teas-yang-te-types], while the OTN-specific attributes,
such as odu-type, are indicated in ietf-layer1-types in this
document.
4.2. Content in Layer 1 Type Module
The module ietf-layer1-types contains the following YANG reusable
types and groupings:
tributary-slot-granularity:
This is to define the granularity of the server layer ODU Link (HO
ODUk or ODUCn) supporting a client layer ODU LSP (LO ODUj or ODUk,
respectively). Three granularities, 1.25G/2.5G/5G, have been
specified.
Zheng & Busi Expires September 10, 2020 [Page 3]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
odu-type:
This is to specify the type of ODUk LSP, including the types
specified in [RFC7139] and [RFC7963].
client-signal:
This is to specify the client signal types of OTN networks. The
initial input was the G-PID specified in [RFC7139]. Identities about
a few categories of client signal types, including ETH, STM-n, OC
[Telcordia] and Fiber Channel have been specified.
otn-label-range-type:
The label range type of OTN has two different representations,
tributary slots (TS) and tributary port number (TPN), according to
[RFC7139]. Respective representation is specified under this same
base type.
otn-link-bandwidth:
This grouping defines the link bandwidth information and could be
used in OTN topology model for bandwidth representation. All the
bandwidth related sections in generic module,
[I-D.ietf-teas-yang-te-types], need to be augmented with this
grouping for the usage of Layer 1.
otn-path-bandwidth:
This grouping defines the path bandwidth information and could be
used in OTN topology model for bandwidth representation. All the
bandwidth related sections in generic module,
[I-D.ietf-teas-yang-te-types], need to be augmented with this
grouping for the usage of Layer 1. This grouping is also applicable
to set up the OTN tunnel.
otn-label-range-info and otn-label-step:
These groupings are used for the augmentation of OTN label in a
specific way.
otn-label-start-end and otn-label-hop:
These groupings are used for the augmentation of label for OTN link
and path respectively.
optical-interface-func:
Zheng & Busi Expires September 10, 2020 [Page 4]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
The optical interface function is specified in [MEF63]. This
grouping describes the functionality which encodes bits for
transmission and the corresponding decode upon reception.
service-performance-metric:
The service performance metric is a quantitative characterization of
Layer 1 characteristic information delivery quality experienced by
the Layer 1 subscriber.
4.3. OTN Label and Label Range
As described in [RFC7139], the OTN label usually represents the
Tributary Port Number (TPN) and the related set of Tributary Slots
(TS) assigned to a client layer ODU LSP (LO ODUj or ODUk) on a given
server layer ODU (HO-ODU or ODUCn, respectively) Link (e.g., ODU2 LSP
over ODU3 Link). Some special OTN label values are also defined for
an ODUk LSP being setup over an OTUk Link.
The same OTN label shall be assigned to the same ODUk LSP at the two
ends of an OTN Link.
As described in [RFC7139], TPN can be a number from 1 to 4095 and TS
are numbered from 1 to 4095, although the actual maximum values
depend on the type of server layer ODU. For example, a server layer
ODU4 provides 80 time slots (numbered from 1 to 80) and the TPN
values can be any number from 1 to 80.
The OTN Label Range represents the values for the TPN and TS that are
available for ODUk LSPs to be setup over a given OTN Link.
The OTN Label Range is defined by the label-restriction list, defined
in [I-D.ietf-teas-yang-te-types], which, for OTN, should be augmented
using the otn-label-range-info grouping.
Each entry in the label-restriction list represents either the range
of the available TPN values or the range of the available TS values:
the range-type attribute in the otn-label-range-info grouping defines
the type of range for each entry of the list.
Each entry of the label-restriction list, as defined in
[I-D.ietf-teas-yang-te-types], defines a label-start, a label-end, a
label-step and a range-bitmap. The label-start and label-end
definitions for OTN should be augmented using the otn-label-start-end
grouping. The label-step definition for OTN should be augmented
using the otn-label-step grouping. It is expected that the otn-
label-step will always be equal to its default value (i.e., 1), which
is defined in [I-D.ietf-teas-yang-te-types].
Zheng & Busi Expires September 10, 2020 [Page 5]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
As described in [RFC7139], in some cases, the TPN assignment rules is
flexible (e.g., ODU4 Link) while in other cases the TPN assignment
rules are fixed (e.g., ODU1 Link). In the former case, both TPN and
TS ranges are reported, while in the latter case, the TPN range is
not reported to indicate that the TPN shall be set equal to the TS
number assigned to the ODUk LSP.
As described in [RFC7139], in some cases, the TPN assignment rules
depends on the TS Granularity (e.g., ODU2 or ODU3 Links). Different
entries in the label-restriction list will report different TPN
ranges for each TS granularity supported by the link, as indicated by
the tsg attribute in the otn-label-range-info grouping.
As described in [RFC7139], in some cases, the TPN ranges are
different for different types of ODUk LSPs. For example, on an ODU2
Link with 1,25G TS granularity, there is TPN range 1-4 for ODU1 and
another TPN range 1-8 in common for ODU0 and ODUflex. Different
entries in the label-restriction list will report different TPN
ranges for different set of ODUk types, as indicated by the odu-type-
list in the otn-label-range-info grouping.
Appendix A provides some examples of how the TPN and TS label ranges
described in Table 3 and Table 4 of [RFC7139] can be represented in
YANG using the groupings defined in this document.
4.4. ODUflex
ODUflex is a type of ODU which has a flexible bit rate which should
be configured when setting up an ODUflex LSP.
[ITU-Tg709], defines six types of ODUflex: ODUflex(CBR),
ODUflex(GFP), ODUflex(GFP,n,k), ODUflex(IMP), ODUflex(IMP,s) and
ODUflex(FlexE-aware).
The main difference between these types of ODUflex is the formula
used to calculate the nominal bit rate of the ODUflex, as described
in Table 7-2 of [ITU-Tg709]. A choice has been defined to describe
these cases:
Zheng & Busi Expires September 10, 2020 [Page 6]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
+--rw (oduflex-type)?
+--:(generic)
| +--rw nominal-bit-rate uint64
+--:(cbr)
| +--rw client-type identityref
+--:(gfp-n-k)
| +--rw gfp-n uint8
| +--rw gfp-k? l1-types:gfp-k
+--:(flexe-client)
| +--rw flexe-client
| l1-types:flexe-client-rate
+--:(flexe-aware)
| +--rw flexe-aware-n uint16
+--:(packet)
+--rw opuflex-payload-rate uint64
The (generic) case has been added to allow defining the ODUflex
nominal bit rate independently from the type of ODUflex. This could
be useful for forward compatibility in the transit domain/nodes where
the setup of ODUflex LSPs does not depend from the ODUflex type.
In order to simplify interoperability it is recommended to use
(generic) case only when needed and to use the ODUflex specific type
case whenever possible.
The (cbr) case is used for Constant Bit Rate (CBR) client signals.
The client-type indicates which is the CBR client signal carried by
the ODUflex and, implicitly, also the client signal bit rate which is
used to calculate the ODUflex(CBR) nominal bit rate as described in
Table 7-2 of [ITU-Tg709].
The (gfp-n-k) case is used for GFP-F mapped client signals based on
ODUk.ts and n 1.25G tributary slots. The gfp-k defines the nominal
bit-rate of the ODUk.ts which, together with the value of gfp-n, is
used to calculated the ODUflex(GFP,n,k) nominal bit rate as described
in Table 7-8 and Table L-7 of [ITU-Tg709] . With few exceptions,
shown in Table L-7 of [ITU-Tg709], the nominal bit-rate of the
ODUk.ts could be inferred from the value of n, as shown in Table 7-8
of [ITU-Tg709] and therefore the gfp-k is optional.
The (flexe-client) case is used for IMP mapped FlexE Client signals,
The flexe-client represents the type of FlexE Client carried by the
ODUflex which implicitly defines the value of s used to calculate the
ODUflex(s) nominal bit rate as described in Table 7-2 of [ITU-Tg709].
The '10G' and '40G' enumeration values are used for 10G and 40G FlexE
Clients to implicitly define the values of s=2 and s=8. For the n x
Zheng & Busi Expires September 10, 2020 [Page 7]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
25G FlexE Clients the value of n is used to defines the value of s=5
x n.
The (flexe-aware) case is used for FlexE-aware client signals. The
flexe-aware-n represents the value n (n = n1 + n2 + ... + np) which
is used to calculate the ODUflex(FlexE-aware) nominal bit rate as
described in Table 7-2 of [ITU-Tg709].
When (packet) case is used for both the GFP-F mapped client signals
and the IMP mapped client signals. The opuflex-payload-rate is
either the GFP-F encapsulated packet client nominal bit rate or the
64b/66b encoded packet client nominal bit rate. The calculation of
ODUflex(GFP) nominal bit rate is defined in section 12.2.5 of
[ITU-Tg709], and the calculation of ODUflex(IMP) nominal bit rate is
defined in section 12.2.6 of [ITU-Tg709]. The same formula is used
in both cases.
Section 5.1 and 5.2 of [RFC7139] defines two rules to compute the
number of tributary slots to be allocated to ODUflex(CBR) and
ODUflex(GFP) LSPs when carried over an HO-ODUk link. According to
section 19.6 of [ITU-Tg709], the rules in section 5.2 applies only to
ODUflex(GFP,n,k) while the rules defined in section 5.1 applies to
any other ODUflex type, including but not being limited to
ODUflex(CBR). Section 20.5 of [ITU-Tg709] defines the rules to
compute the number of tributary slots to be allocated to ODUflex LSPs
when carried over an ODUCn link.
Following the [ITU-Tg709] definitions, the rules defined for
ODUflex(GFP,n,k) are used only when the (gfp-n-k) case is used. In
all the other cases, including the (generic) case, the rules defined
any other ODUflex type are used.
The number of available ODUs, defined for each ODUk type, including
ODUflex, together with the number of available time-slots, reported
as part of the OTN label range, provides sufficient information to
infer the OTN link bandwidth availability for ODUflex LSPs. This
information is independent from the ODUflex type.
4.4.1. Resizable ODUflex
Resizable ODUflex is a special type of ODUflex that supports the
procedures defined in [ITU-Tg7044] for hitless resizing of the
ODUflex nominal bit rate.
Two odu-type identities have been defined for ODUflex:
o The ODUflex identity, which is used with any type of non-resizable
ODUflex, as defined in Table 7-2 of [ITU-Tg709].
Zheng & Busi Expires September 10, 2020 [Page 8]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
o The ODUflex-resizable identity, which used only with resizable
ODUflex(GFP,n,k).
These two identities are used to identify whether an ODUflex(GFP,n,k)
LSP shall or not support the [ITU-Tg7044] hitless resizing procedures
as well as whether an OTN link supports only the setup of non-
resizable ODUflex LSPs or also the setup of resizable
ODUflex(GFP,n,k) LSP but with different capabilities (e.g., a lower
number of LSPs).
5. YANG Code for Layer1 Types
<CODE BEGINS>file "ietf-layer1-types@2020-03-09.yang"
module ietf-layer1-types {
yang-version 1.1;
namespace "urn:ietf:params:xml:ns:yang:ietf-layer1-types";
prefix "l1-types";
organization
"IETF CCAMP Working Group";
contact
"WG Web: <http://tools.ietf.org/wg/ccamp/>
WG List: <mailto:ccamp@ietf.org>
Editor: Haomian Zheng
<mailto:zhenghaomian@huawei.com>
Editor: Italo Busi
<mailto:Italo.Busi@huawei.com>";
description
"This module defines Layer 1 types. The model fully conforms
to the Network Management Datastore Architecture (NMDA).
Copyright (c) 2020 IETF Trust and the persons
identified as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(https://trustee.ietf.org/license-info).
This version of this YANG module is part of RFC XXXX; see
the RFC itself for full legal notices.";
revision "2020-03-09" {
Zheng & Busi Expires September 10, 2020 [Page 9]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
description
"Initial Version";
reference
"RFC XXXX: A YANG Data Model for Layer 1 Types";
// RFC Editor: replace XXXX with actual RFC number, update date
// information and remove this note
}
typedef otn-tpn
{
type uint16 {
range "1..4095";
}
description
"Tributary Port Number for OTN. ";
reference
"RFC7139: GMPLS Signaling Extensions for Control of Evolving
G.709 Optical Transport Networks.";
}
typedef otn-ts
{
type uint16 {
range "1..4095";
}
description
"Tributary Slot for OTN. ";
reference
"RFC7139: GMPLS Signaling Extensions for Control of Evolving
G.709 Optical Transport Networks.";
}
typedef otn-label-range-type {
type enumeration {
enum trib-slot {
description
"Defines a range of OTN tributary slots. ";
}
enum trib-port {
description
"Defines a range of OTN tributary ports. ";
}
}
description
"Defines the type of OTN label range: TS or TPN. ";
}
typedef gfp-k {
Zheng & Busi Expires September 10, 2020 [Page 10]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
type enumeration {
enum 2 {
description
"The ODU2.ts rate (1,249,177.230 kbit/s) is used
to compute the rate of an ODUflex(GFP,n,2). ";
}
enum 3 {
description
"The ODU3.ts rate (1,254,470.354 kbit/s) is used
to compute the rate of an ODUflex(GFP,n,3). ";
}
enum 4 {
description
"The ODU4.ts rate (1,301,467.133 kbit/s) is used
to compute the rate of an ODUflex(GFP,n,4). ";
}
}
description
"The ODUk.ts used to compute the rate of an ODUflex(GFP,n,k)";
reference
"Table 7-8 and L-7 of G.709";
}
typedef flexe-client-rate {
type union {
type uint16;
type enumeration {
enum "10G" {
description
"Represents a 10G FlexE Client signal (s=2)";
}
enum "40G" {
description
"Represents a 40G FlexE Client signal (s=8)";
}
}
}
description
"The FlexE Client signal rate (s x 5,156,250.000 kbit/s)
used to compute the rate of an ODUflex(IMP, s).
Valid values for s are s=2 (10G), s=4 (40G) and
s=5 x n (n x 25G).
In the first two cases an enumeration value
(either 10G or 40G) is used, while in the latter case
the value of n is used";
reference
"Table 7-2 of G.709";
}
Zheng & Busi Expires September 10, 2020 [Page 11]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
identity tributary-slot-granularity {
description
"Tributary slot granularity";
reference
"G.709/Y.1331, February 2016: Interfaces for the Optical
Transport Network (OTN)";
}
identity tsg-1.25G {
base tributary-slot-granularity;
description
"1.25G tributary slot granularity";
}
identity tsg-2.5G {
base tributary-slot-granularity;
description
"2.5G tributary slot granularity";
}
identity tsg-5G {
base tributary-slot-granularity;
description
"5G tributary slot granularity";
}
identity odu-type {
description
"Base identity for protocol framing used by tributary signals.";
}
identity ODU0 {
base odu-type;
description
"ODU0 protocol (1.24Gb/s). ";
reference "RFC7139/ITU-T G.709";
}
identity ODU1 {
base odu-type;
description
"ODU1 protocol (2.49Gb/s).";
reference "RFC7139/ITU-T G.709";
}
identity ODU1e {
base odu-type;
description
Zheng & Busi Expires September 10, 2020 [Page 12]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
"ODU1e protocol (10.35Gb/s).";
reference "RFC7963/ITU-T G.sup43";
}
identity ODU2 {
base odu-type;
description
"ODU2 protocol (10.03Gb/s).";
reference "RFC7139/ITU-T G.709";
}
identity ODU2e {
base odu-type;
description
"ODU2e protocol (10.39Gb/s).";
reference "RFC7139/ITU-T G.709";
}
identity ODU3 {
base odu-type;
description
"ODU3 protocol (40.31Gb/s).";
reference "RFC7139/ITU-T G.709";
}
identity ODU3e1 {
base odu-type;
description
"ODU3e1 protocol (41.77Gb/s).";
reference "RFC7963/ITU-T G.sup43";
}
identity ODU3e2 {
base odu-type;
description
"ODU3e2 protocol (41.78Gb/s).";
reference "RFC7963/ITU-T G.sup43";
}
identity ODU4 {
base odu-type;
description
"ODU4 protocol (104.79Gb/s).";
reference "RFC7139/ITU-T G.709";
}
identity ODUflex {
base odu-type;
Zheng & Busi Expires September 10, 2020 [Page 13]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
description
"ODUflex protocol (flexibile bit rate, not resizable).
It could be used for any type of ODUflex, including
ODUflex(CBR), ODUflex(GFP), ODUflex(GFP,n,k), ODUflex(IMP,s),
ODUflex(IMP) and ODUflex(FlexE-aware).";
reference "RFC7139/ITU-T G.709";
}
identity ODUflex-resizable {
base odu-type;
description
"ODUflex protocol (flexibile bit rate, resizable).
It could be used only for ODUflex(GFP,n,k).";
reference "RFC7139/ITU-T G.709 and ITU-T G.7044";
}
identity client-signal {
description
"Base identity from which specific client signals for the
tunnel are derived";
}
identity ETH-1Gb {
base client-signal;
description
"Client signal type of 1GbE";
reference "RFC7139/ITU-T G.709";
}
identity ETH-10Gb-LAN {
base client-signal;
description
"Client signal type of ETH-10Gb-LAN (10.3 Gb/s)";
reference "RFC7139/ITU-T G.709/IEEE 802.3 Clause 49";
}
identity ETH-10Gb-WAN {
base client-signal;
description
"Client signal type of ETH-10Gb-WAN (9.95 Gb/s)";
reference "RFC7139/ITU-T G.709/IEEE 802.3 Clause 50";
}
identity ETH-40Gb {
base client-signal;
description
"Client signal type of 40GbE";
reference "RFC7139/ITU-T G.709";
Zheng & Busi Expires September 10, 2020 [Page 14]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
}
identity ETH-100Gb {
base client-signal;
description
"Client signal type of 100GbE";
reference "RFC7139/ITU-T G.709";
}
identity STM-1 {
base client-signal;
description
"Client signal type of STM-1";
reference "RFC7139/ITU-T G.709";
}
identity STM-4 {
base client-signal;
description
"Client signal type of STM-4";
reference "RFC7139/ITU-T G.709";
}
identity STM-16 {
base client-signal;
description
"Client signal type of STM-16";
reference "RFC7139/ITU-T G.709";
}
identity STM-64 {
base client-signal;
description
"Client signal type of STM-64";
reference "RFC7139/ITU-T G.709";
}
identity STM-256 {
base client-signal;
description
"Client signal type of STM-256";
reference "RFC7139/ITU-T G.709";
}
identity OC-3 {
base client-signal;
description
"Client signal type of OC3";
reference "Telcordia GR-253-CORE";
Zheng & Busi Expires September 10, 2020 [Page 15]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
}
identity OC-12 {
base client-signal;
description
"Client signal type of OC12";
reference "Telcordia GR-253-CORE";
}
identity OC-48 {
base client-signal;
description
"Client signal type of OC48";
reference "Telcordia GR-253-CORE";
}
identity OC-192 {
base client-signal;
description
"Client signal type of OC192";
reference "Telcordia GR-253-CORE";
}
identity OC-768 {
base client-signal;
description
"Client signal type of OC768";
reference "Telcordia GR-253-CORE";
}
identity FC-100 {
base client-signal;
description
"Client signal type of Fibre Channel FC-100";
reference "RFC4328/RFC7139";
}
identity FC-200 {
base client-signal;
description
"Client signal type of Fibre Channel FC-200";
reference "RFC4328/RFC7139";
}
identity FC-400 {
base client-signal;
description
"Client signal type of Fibre Channel FC-400";
Zheng & Busi Expires September 10, 2020 [Page 16]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
reference "RFC4328/RFC7139";
}
identity FC-800 {
base client-signal;
description
"Client signal type of Fibre Channel FC-800";
reference "RFC4328/RFC7139";
}
identity FC-1200 {
base client-signal;
description
"Client signal type of Fibre Channel FC-1200";
reference "RFC4328/RFC7139";
}
identity FC-1600 {
base client-signal;
description
"Client signal type of Fibre Channel FC-1600";
reference "RFC4328/RFC7139";
}
identity FC-3200 {
base client-signal;
description
"Client signal type of Fibre Channel FC-3200";
reference "RFC4328/RFC7139";
}
identity FICON-4G {
base client-signal;
description
"Client signal type of Fibre Connection 4G";
reference "RFC4328/RFC7139";
}
identity FICON-8G {
base client-signal;
description
"Client signal type of Fibre Connection 8G";
reference "RFC4328/RFC7139";
}
identity coding-func {
description
"Base identity from which coding function is derived.";
Zheng & Busi Expires September 10, 2020 [Page 17]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity ETH-1000X {
base "coding-func";
description
"PCS clause 36 coding function that corresponds to
1000BASE-X";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity ETH-10GW {
base "coding-func";
description
"PCS clause 49 and WIS clause 50 coding func that
corresponds to 10GBASE-W (WAN PHY)";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity ETH-10GR {
base "coding-func";
description
"PCS clause 49 coding function that corresponds to
10GBASE-R (LAN PHY)";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity ETH-40GR {
base "coding-func";
description
"PCS clause 82 coding function that corresponds to
40GBASE-R";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity ETH-100GR {
base "coding-func";
description
"PCS clause 82 coding function that corresponds to
100GBASE-R";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity optical-interface-func {
description
"base identity from which optical-interface-function is
derived.";
reference "MEF63: Subscriber Layer 1 Service Attributes";
Zheng & Busi Expires September 10, 2020 [Page 18]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
}
identity SX-PMD-1000 {
base "optical-interface-func";
description
"SX-PMD-clause-38 Optical Interface function for
1000BASE-X PCS-36";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity LX-PMD-1000 {
base "optical-interface-func";
description
"LX-PMD-clause-38 Optical Interface function for
1000BASE-X PCS-36";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity LX10-PMD-1000 {
base "optical-interface-func";
description
"LX10-PMD-clause-59 Optical Interface function for
1000BASE-X PCS-36";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity BX10-PMD-1000 {
base "optical-interface-func";
description
"BX10-PMD-clause-59 Optical Interface function for
1000BASE-X PCS-36";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity LW-PMD-10G {
base "optical-interface-func";
description
"LW-PMD-clause-52 Optical Interface function for
10GBASE-W PCS-49-WIS-50";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity EW-PMD-10G {
base "optical-interface-func";
description
"EW-PMD-clause-52 Optical Interface function for
10GBASE-W PCS-49-WIS-50";
reference "MEF63: Subscriber Layer 1 Service Attributes";
Zheng & Busi Expires September 10, 2020 [Page 19]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
}
identity LR-PMD-10G {
base "optical-interface-func";
description
"LR-PMD-clause-52 Optical Interface function for
10GBASE-R PCS-49";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity ER-PMD-10G {
base "optical-interface-func";
description
"ER-PMD-clause-52 Optical Interface function for
10GBASE-R PCS-49";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity LR4-PMD-40G {
base "optical-interface-func";
description
"LR4-PMD-clause-87 Optical Interface function for
40GBASE-R PCS-82";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity ER4-PMD-40G {
base "optical-interface-func";
description
"ER4-PMD-clause-87 Optical Interface function for
40GBASE-R PCS-82";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity FR-PMD-40G {
base "optical-interface-func";
description
"FR-PMD-clause-89 Optical Interface function for
40GBASE-R PCS-82";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity LR4-PMD-100G {
base "optical-interface-func";
description
"LR4-PMD-clause-88 Optical Interface function for
100GBASE-R PCS-82";
reference "MEF63: Subscriber Layer 1 Service Attributes";
Zheng & Busi Expires September 10, 2020 [Page 20]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
}
identity ER4-PMD-100G {
base "optical-interface-func";
description
"ER4-PMD-clause-88 Optical Interface function for
100GBASE-R PCS-82";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity service-performance-metric {
description
"Base identity of service-specific performance metric";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity one-way-delay {
base "service-performance-metric";
description "one way delay.";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity one-way-errored-second {
base "service-performance-metric";
description "one way errored second";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity one-way-severely-errored-second {
base "service-performance-metric";
description "one way severely errored second";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity one-way-unavailable-second {
base "service-performance-metric";
description "one way unavailable second";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
identity one-way-availability {
base "service-performance-metric";
description "one way availability";
reference "MEF63: Subscriber Layer 1 Service Attributes";
}
grouping otn-link-bandwidth {
description "link bandwidth attributes for OTN";
Zheng & Busi Expires September 10, 2020 [Page 21]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
list odulist {
key "odu-type";
description
"OTN bandwidth definition";
leaf odu-type {
type identityref {
base l1-types:odu-type;
}
description "ODU type";
}
leaf number {
type uint16;
description "Number of ODUs";
}
}
}
grouping otn-path-bandwidth {
description
"path bandwidth attributes for OTN";
leaf odu-type {
type identityref {
base l1-types:odu-type;
}
description "ODU type";
}
choice oduflex-type {
when "odu-type = 'ODUflex' or 'ODUflex-resizable'" {
description
"applicable when odu-type is ODUflex or ODUflex-resizable";
}
description
"Types of ODUflex used to compute the ODUflex
nominal bit rate.";
reference
"Table 7-2 of G.709";
case generic {
leaf nominal-bit-rate {
type uint64;
units "bps";
mandatory true;
description
"Nominal ODUflex bit rate.";
}
}
case cbr {
leaf client-type {
type identityref {
Zheng & Busi Expires September 10, 2020 [Page 22]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
base l1-types:client-signal;
}
mandatory true;
description
"The CBR client signal for an ODUflex(CBR).";
}
}
case gfp-n-k {
leaf gfp-n {
type uint8 {
range "1..80";
}
mandatory true;
description
"The value of n for an ODUflex(GFP,n,k).";
reference
"Tables 7-8 and L-7 of G.709";
}
leaf gfp-k {
type l1-types:gfp-k;
description
"The value of k for an ODUflex(GFP,n,k).
If omitted, it is calculated from the value of gfp-n
as described in Table 7-8 of G.709";
reference
"Tables 7-8 and L-7 of G.709";
}
}
case flexe-client {
leaf flexe-client {
type l1-types:flexe-client-rate;
mandatory true;
description
"The rate of the FlexE-client for an ODUflex(IMP,s).";
}
}
case flexe-aware {
leaf flexe-aware-n {
type uint16;
mandatory true;
description
"The rate of FlexE-aware client signal
for ODUflex(FlexE-aware)";
}
}
case packet {
leaf opuflex-payload-rate {
type uint64;
Zheng & Busi Expires September 10, 2020 [Page 23]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
units "Kbps";
mandatory true;
description
"Either the GFP-F encapsulated packet client nominal
bit rate for an ODUflex(GFP) or the 64b/66b encoded
packet client nominal bit rate for an ODUflex(IMP).";
}
}
}
}
grouping otn-label-range-info {
description
"label range information for OTN, is dependent on the
range-type, must be used together with the following
groupings: otn-label-start-end and otn-label-step. ";
leaf range-type {
type l1-types:otn-label-range-type;
description "The type of range (e.g., TPN or TS)
to which the label range applies";
}
leaf tsg {
type identityref {
base l1-types:tributary-slot-granularity;
}
description
"Tributary slot granularity (TSG) to which the label range
applies.
This leaf shall be present when the range-type is TS;
This leaf can be omitted when mapping an ODUk over an OTUk
Link. In this case the range-type is tpn, with only one entry
(ODUk), and the tpn range has only one value (1). ";
reference
"G.709/Y.1331, February 2016: Interfaces for the
Optical Transport Network (OTN)";
}
leaf-list odu-type-list {
type identityref {
base odu-type;
}
description
"List of ODU types to which the label range applies.
An Empty odu-type-list means that the label range
applies to all the supported ODU types.";
}
leaf priority {
type uint8;
description
Zheng & Busi Expires September 10, 2020 [Page 24]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
"Priority in Interface Switching Capability
Descriptor (ISCD).";
reference "RFC4203.";
}
}
grouping otn-label-start-end {
description
"The OTN label-start or label-end used to specify an OTN label
range. this grouping is dependent on the range-type,
must be used together with the following groupings:
otn-label-range-info and otn-label-step. ";
choice range-type {
description
"OTN label range type, either TPN range or TS range";
case trib-port {
leaf otn-tpn {
when "../../../range-type = 'trib-port'" {
description
"valid only when range-type represented by trib-port";
}
type l1-types:otn-tpn;
description
"Tributary Port Number.";
reference
"RFC7139: GMPLS Signaling Extensions for Control of Evolving
G.709 Optical Transport Networks.";
}
}
case trib-slot {
leaf otn-ts {
when "../../../range-type = 'trib-slot'" {
description
"valid only when range-type represented by trib-slot";
}
type l1-types:otn-ts;
description
"Tributary Slot Number.";
reference
"RFC7139: GMPLS Signaling Extensions for Control of Evolving
G.709 Optical Transport Networks.";
}
}
}
}
grouping otn-label-hop {
description "OTN Label. ";
Zheng & Busi Expires September 10, 2020 [Page 25]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
reference "RFC7139, section 6. ";
leaf otn-tpn {
type l1-types:otn-tpn;
description
"Tributary Port Number.";
reference
"RFC7139: GMPLS Signaling Extensions for Control of Evolving
G.709 Optical Transport Networks.";
}
leaf tsg {
type identityref {
base l1-types:tributary-slot-granularity;
}
description "Tributary slot granularity.";
reference
"G.709/Y.1331, February 2016: Interfaces for the
Optical Transport Network (OTN)";
}
leaf ts-list {
type string {
pattern "([1-9][0-9]{0,3}(-[1-9][0-9]{0,3})?"
+ "(,[1-9][0-9]{0,3}(-[1-9][0-9]{0,3})?)*)";
}
description
"A list of available tributary slots ranging
between 1 and 4095. If multiple values or
ranges are given, they all MUST be disjoint
and MUST be in ascending order.
For example 1-20,25,50-1000. ";
reference
"RFC 7139: GMPLS Signaling Extensions for Control
of Evolving G.709 Optical Transport Networks";
}
}
grouping otn-label-step {
description
"Label step for OTN, is dependent on the range-type,
must be used together with the following groupings:
otn-label-range-info and otn-label-start-end. ";
choice range-type {
description
"OTN label range type, either TPN range or TS range";
case trib-port {
leaf otn-tpn {
when "../../../range-type = 'trib-port'" {
description
"valid only when range-type represented by trib-port";
Zheng & Busi Expires September 10, 2020 [Page 26]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
}
type l1-types:otn-tpn;
description
"Label step which represents possible increments for
Tributary Port Number.";
reference
"RFC7139: GMPLS Signaling Extensions for Control of
Evolving G.709 Optical Transport Networks.";
}
}
case trib-slot {
leaf otn-ts {
when "../../../range-type = 'trib-slot'" {
description
"valid only when range-type represented by trib-slot";
}
type l1-types:otn-ts;
description
"Label step which represents possible increments for
Tributary Slot Number.";
reference
"RFC7139: GMPLS Signaling Extensions for Control of Evolving
G.709 Optical Transport Networks.";
}
}
}
}
}
<CODE ENDS>
6. Security Considerations
The YANG module specified in this document defines a schema for data
that is designed to be accessed via network management protocols such
as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer
is the secure transport layer, and the mandatory-to-implement secure
transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer
is HTTPS, and the mandatory-to-implement secure transport is TLS
[RFC8446].
The NETCONF access control model [RFC8341] provides the means to
restrict access for particular NETCONF or RESTCONF users to a
preconfigured subset of all available NETCONF or RESTCONF protocol
operations and content.
Zheng & Busi Expires September 10, 2020 [Page 27]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
The YANG module in this document defines layer 1 type definitions
(i.e., typedef, identity and grouping statements) in YANG data
modeling language to be imported and used by other layer 1
technology-specific modules. When imported and used, the resultant
schema will have data nodes that can be writable, or readable. The
access to such data nodes may be considered sensitive or vulnerable
in some network environments. Write operations (e.g., edit-config)
to these data nodes without proper protection can have a negative
effect on network operations.
The security considerations spelled out in the YANG 1.1 specification
[RFC7950] apply for this document as well.
7. IANA Considerations
It is proposed that IANA should assign new URIs from the "IETF XML
Registry" [RFC3688] as follows:
URI: urn:ietf:params:xml:ns:yang:ietf-layer1-types
Registrant Contact: The IESG
XML: N/A; the requested URI is an XML namespace.
This document registers following YANG modules in the YANG Module
Names registry [RFC7950].
name: ietf-layer1-types
namespace: urn:ietf:params:xml:ns:yang:ietf-otn-types
prefix: l1-types
reference: RFC XXXX
8. Acknowledgements
The authors and the working group give their sincere thanks for
Robert Wilton for the YANG doctor review, and Tom Petch for his
comments during the model and document development.
9. Contributors
Dieter Beller
Nokia
Email: dieter.beller@nokia.com
Sergio Belotti
Nokia
Zheng & Busi Expires September 10, 2020 [Page 28]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
Email: sergio.belotti@nokia.com
Yanlei Zheng
China Unicom
Email: zhengyanlei@chinaunicom.cn
Aihua Guo
Futurewei Technologies
Email: aihuaguo@futurewei.com
Young Lee
Samsung
Email: younglee.tx@gmail.com
Lei Wang
China Mobile
Email: wangleiyj@chinamobile.com
Oscar Gonzalez de Dios
Telefonica
Email: oscar.gonzalezdedios@telefonica.com
Xufeng Liu
Volta Networks
Email: xufeng.liu.ietf@gmail.com
Yunbin Xu
CAICT
Email: xuyunbin@caict.ac.cn
Anurag Sharma
Google
Email: ansha@google.com
Rajan Rao
Infinera
Email: rrao@infinera.com
Victor Lopez
Telefonica
Email: victor.lopezalvarez@telefonica.com
Yunbo Li
China Mobile
Email: liyunbo@chinamobile.com
Zheng & Busi Expires September 10, 2020 [Page 29]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
10. References
10.1. Normative References
[I-D.ietf-teas-yang-te-types]
Saad, T., Gandhi, R., Liu, X., Beeram, V., and I. Bryskin,
"Traffic Engineering Common YANG Types", draft-ietf-teas-
yang-te-types-13 (work in progress), November 2019.
[ITU-Tg7044]
International Telecommunication Union, "Hitless adjustment
of ODUflex(GFP)", ITU-T G.7044, October 2011.
[ITU-Tg709]
International Telecommunication Union, "Interfaces for the
optical transport network", ITU-T G.709, March 2020.
[ITU-Tgsup43]
International Telecommunication Union, "Transport of IEEE
10GBASE-R in optical transport networks (OTN)",
ITU-T G.sup43, February 2011.
[MEF63] Metro Ethernet Forum, "Subscriber Layer1 Service
Attributes Technical Specification", MEF 63, August 2018.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
DOI 10.17487/RFC3688, January 2004,
<https://www.rfc-editor.org/info/rfc3688>.
[RFC6241] Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
and A. Bierman, Ed., "Network Configuration Protocol
(NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
<https://www.rfc-editor.org/info/rfc6241>.
[RFC6242] Wasserman, M., "Using the NETCONF Protocol over Secure
Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
<https://www.rfc-editor.org/info/rfc6242>.
[RFC7139] Zhang, F., Ed., Zhang, G., Belotti, S., Ceccarelli, D.,
and K. Pithewan, "GMPLS Signaling Extensions for Control
of Evolving G.709 Optical Transport Networks", RFC 7139,
DOI 10.17487/RFC7139, March 2014,
<https://www.rfc-editor.org/info/rfc7139>.
[RFC7950] Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
RFC 7950, DOI 10.17487/RFC7950, August 2016,
<https://www.rfc-editor.org/info/rfc7950>.
Zheng & Busi Expires September 10, 2020 [Page 30]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
[RFC7963] Ali, Z., Bonfanti, A., Hartley, M., and F. Zhang, "RSVP-TE
Extension for Additional Signal Types in G.709 Optical
Transport Networks (OTNs)", RFC 7963,
DOI 10.17487/RFC7963, August 2016,
<https://www.rfc-editor.org/info/rfc7963>.
[RFC8040] Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
<https://www.rfc-editor.org/info/rfc8040>.
[RFC8341] Bierman, A. and M. Bjorklund, "Network Configuration
Access Control Model", STD 91, RFC 8341,
DOI 10.17487/RFC8341, March 2018,
<https://www.rfc-editor.org/info/rfc8341>.
[RFC8342] Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
and R. Wilton, "Network Management Datastore Architecture
(NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
<https://www.rfc-editor.org/info/rfc8342>.
[RFC8446] Rescorla, E., "The Transport Layer Security (TLS) Protocol
Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
<https://www.rfc-editor.org/info/rfc8446>.
[Telcordia]
Telcordia, "Synchronous Optical Network Transport Systems:
Common Generic Criteria, Issue 5", Telcordia GR-253-CORE,
October 2009.
10.2. Informative References
[I-D.ietf-ccamp-client-signal-yang]
Zheng, H., Guo, A., Busi, I., Snitser, A., Lazzeri, F.,
Xu, Y., Zhao, Y., Liu, X., and G. Fioccola, "A YANG Data
Model for Transport Network Client Signals", draft-ietf-
ccamp-client-signal-yang-01 (work in progress), November
2019.
[I-D.ietf-ccamp-l1csm-yang]
Lee, Y., Lee, K., Zheng, H., Dhody, D., Dios, O., and D.
Ceccarelli, "A YANG Data Model for L1 Connectivity Service
Model (L1CSM)", draft-ietf-ccamp-l1csm-yang-10 (work in
progress), September 2019.
Zheng & Busi Expires September 10, 2020 [Page 31]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
[I-D.ietf-ccamp-otn-topo-yang]
Zheng, H., Busi, I., Liu, X., Belotti, S., and O. Dios, "A
YANG Data Model for Optical Transport Network Topology",
draft-ietf-ccamp-otn-topo-yang-09 (work in progress),
November 2019.
[I-D.ietf-ccamp-otn-tunnel-model]
Zheng, H., Busi, I., Belotti, S., Lopezalvarez, V., and Y.
Xu, "OTN Tunnel YANG Model", draft-ietf-ccamp-otn-tunnel-
model-09 (work in progress), November 2019.
[I-D.ietf-ccamp-transport-nbi-app-statement]
Busi, I., King, D., Zheng, H., and Y. Xu, "Transport
Northbound Interface Applicability Statement", draft-ietf-
ccamp-transport-nbi-app-statement-10 (work in progress),
November 2019.
[I-D.ietf-netmod-artwork-folding]
Watsen, K., Auerswald, E., Farrel, A., and Q. WU,
"Handling Long Lines in Inclusions in Internet-Drafts and
RFCs", draft-ietf-netmod-artwork-folding-12 (work in
progress), January 2020.
[RFC7062] Zhang, F., Ed., Li, D., Li, H., Belotti, S., and D.
Ceccarelli, "Framework for GMPLS and PCE Control of G.709
Optical Transport Networks", RFC 7062,
DOI 10.17487/RFC7062, November 2013,
<https://www.rfc-editor.org/info/rfc7062>.
[RFC7138] Ceccarelli, D., Ed., Zhang, F., Belotti, S., Rao, R., and
J. Drake, "Traffic Engineering Extensions to OSPF for
GMPLS Control of Evolving G.709 Optical Transport
Networks", RFC 7138, DOI 10.17487/RFC7138, March 2014,
<https://www.rfc-editor.org/info/rfc7138>.
Appendix A. Examples of OTN Label Ranges
This appendix provides some examples of how the TPN and TS label
ranges described in Table 3 and Table 4 of [RFC7139] can be
represented in YANG using the groupings defined in this document.
It also considers the OTUk links in addition to HO-ODUk links.
The JSON code examples provided in this appendix provides some
embedded comments following the conventions in section 3.2 of [I-
D.ietf-ccamp-transport-nbi-app-statement] and have been folded using
the tool in [I-D.ietf-netmod-artwork-folding].
Zheng & Busi Expires September 10, 2020 [Page 32]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
========== NOTE: '\\' line wrapping per BCP XXX (RFC XXXX) ==========
{
"examples of label-restrictions for different OTN Links": [
{
"// ": "HO-ODU1 or OTU1 Link",
"label-restrictions": {
"label-restriction": [
{
"index ": 1,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"// ___NOT-PRESENT___ tsg": "",
"odu-type-list": "[ ODU1 ]",
"// ___DEFAULT___ priority": 7,
"// tpn-range": 1,
"// ___ COMMENT ___": "Since no TS range and no TSG are \
\reported for ODU1, the link is an OTU1 Link. TS allocation is not n\
\eeded and TPN shall be set to '1' for mapping ODU1 over OTU1. This \
\entry is not present if the OTN Link is an HO-ODU1 Link."
},
{
"index ": 2,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-slot",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODU0 ]",
"// ts-range": "1-2",
"// ___ COMMENT ___": "Since no TPN range is reportd for\
\ ODU0 with 1.25G TSG, the TPN allocation rule is fixed (TPN = TS#) \
\for mapping LO-ODU0 over HO-ODU1 with 1.25G TSG. See Table 4 of [RF\
\C7139]."
}
]
}
},
{
"// ": "HO-ODU2 or OTU2 Link",
"label-restrictions": {
"label-restriction": [
{
"index ": 1,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"// ___NOT-PRESENT___ tsg": "",
"odu-type-list": "[ ODU2 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": 1,
Zheng & Busi Expires September 10, 2020 [Page 33]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
"// ___ COMMENT ___": "Since no TS range and no TSG are \
\reported for ODU2, the link is an OTU2 Link. TS allocation is not n\
\eeded and TPN shall be set to '1' for mapping ODU2 over OTU2. This \
\entry is not present if the OTN Link is an HO-ODU2 Link."
},
{
"index ": 2,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-slot",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0, ODU1\
\ ]",
"// ___ DEFAULT ___ priority": 7,
"// ts-range": "1-8"
},
{
"index ": 3,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-1.25G ",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-8",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for ODUflex and ODU0 with 1.25G TSG, the TPN assignment rule is fle\
\xible within a common range for mapping LO-ODUflex and LO-ODU0 over\
\ HO-ODU2 with 1.25G TSG. See Table 4 of [RFC7139]."
},
{
"index ": 4,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODU1 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-4",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for ODU1 with 1.25G TSG, the TPN assignment rule is flexible within\
\ a common range for mapping LO-ODU1 over HO-ODU2 with 1.25G TSG. Se\
\e Table 4 of [RFC7139]."
},
{
"index ": 5,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-slot",
"tsg": "tsg-2.5G",
"odu-type-list": "[ ODU1 ]",
"// ___ DEFAULT ___ priority": 7,
Zheng & Busi Expires September 10, 2020 [Page 34]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
"// ts-range": "1-4",
"// ___ COMMENT ___": "Since no TPN range is reported fo\
\r ODU1 with 2.5G TSG, the TPN allocation rule is fixed (TPN = TS#) \
\for mapping LO-ODU1 over HO-ODU2 with 2.5G TSG. See Table 3 of [RFC\
\7139]."
}
]
}
},
{
"// ": "HO-ODU3 or OTU3 Link",
"label-restrictions": {
"label-restriction": [
{
"index ": 1,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"// ___NOT-PRESENT___ tsg": "",
"odu-type-list": "[ ODU3 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": 1,
"// ___ COMMENT ___": "Since no TS range and no TSG are \
\reported for ODU3, the link is an OTU3 Link. TS allocation is not n\
\eeded and TPN shall be set to '1' for mapping ODU3 over OTU3. This \
\entry is not present if the OTN Link is an HO-ODU3 Link."
},
{
"index ": 2,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-slot",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0, ODU1\
\, ODU2, ODU2e ]",
"// ___ DEFAULT ___ priority": 7,
"// ts-range": "1-32"
},
{
"index ": 3,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0, ODU2\
\e ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-32",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for ODUflex, ODU0 and ODU2e with 1.25G TSG, the TPN assignment rule\
\ is flexible within a common range for mapping LO-ODUflex, LO-ODU0 \
Zheng & Busi Expires September 10, 2020 [Page 35]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
\and LO-ODU2e over HO-ODU3 with 1.25G TSG. See Table 4 of [RFC7139]."
},
{
"index ": 4,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODU1 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-16",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for ODU1 with 1.25G TSG, the TPN assignment rule is flexible within\
\ a common range for mapping LO-ODU1 over HO-ODU3 with 1.25G TSG. Se\
\e Table 4 of [RFC7139]."
},
{
"index ": 5,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODU2 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-4",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for ODU2 with 1.25G TSG, the TPN assignment rule is flexible within\
\ a common range for mapping LO-ODU2 over HO-ODU3 with 1.25G TSG. Se\
\e Table 4 of [RFC7139]."
},
{
"index ": 6,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-slot",
"tsg": "tsg-2.5G",
"odu-type-list": "[ ODU1, ODU2 ]",
"// ___ DEFAULT ___ priority": 7,
"// ts-range": "1-16"
},
{
"index ": 7,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-2.5G ",
"odu-type-list": "[ ODU2 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-4",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for ODU2 with 2.5G TSG, the TPN assignment rule is flexible within \
\a common range for mapping LO-ODU2 over HO-ODU3. Since no TPN range\
Zheng & Busi Expires September 10, 2020 [Page 36]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
\ is reported for ODU1 with 2.5G TSG, the TPN allocation rule is fix\
\ed (TPN = TS#) for mapping LO-ODU1 over HO-ODU3 with 2.5G TSG. See \
\Table 3 of [RFC7139]."
}
]
}
},
{
"// ": "HO-ODU4 or OTU4 Link",
"label-restrictions": {
"label-restriction": [
{
"index ": 1,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"// ___NOT-PRESENT___ tsg": "",
"odu-type-list": "[ ODU4 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": 1,
"// ___ COMMENT ___": "Since no TS range and no TSG are \
\reported for ODU4, the link is an OTU4 Link. TS allocation is not n\
\eeded and TPN shall be set to '1' for mapping ODU4 over OTU4. This \
\entry is not present if the OTN Link is an HO-ODU4 Link."
},
{
"index ": 2,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-slot",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0, ODU1\
\, ODU2, ODU2e, ODU3 ]",
"// ___ DEFAULT ___ priority": 7,
"// ts-range": "1-80"
},
{
"index ": 3,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-1.25G",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0, ODU1\
\, ODU2, ODU2e, ODU3 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-80",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for any LO-ODUj with 1.25G TSG, the TPN assignment rule is flexible\
\ within a common range for mapping any LO-ODUj over HO-ODU4 with 1.\
\25G TSG. See Table 4 of [RFC7139]."
}
Zheng & Busi Expires September 10, 2020 [Page 37]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
]
}
},
{
"// ": "ODUC1 Link",
"label-restrictions": {
"label-restriction": [
{
"index ": 1,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-slot",
"tsg": "tsg-5G",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0, ODU1\
\, ODU2, ODU2e, ODU3, ODU4 ]",
"// ___ DEFAULT ___ priority": 7,
"// ts-range": "1-20",
"// ___ COMMENT ___": "Since the TS range is specified f\
\or any ODUk, the OTN Link is an ODUCn Link."
},
{
"index ": 2,
"// ___DEFAULT___ restriction": "inclusive",
"range-type": "label-range-trib-port",
"tsg": "tsg-5G",
"odu-type-list": "[ ODUFlex-cbr, ODUFlex-gfp, ODU0, ODU1\
\, ODU2, ODU2e, ODU3, ODU4 ]",
"// ___ DEFAULT ___ priority": 7,
"// tpn-range": "1-10",
"// ___ COMMENT ___": "Since this TPN range is reported \
\for any ODUk with 5G TSG, the TPN assignment rule is flexible withi\
\n a common range for mapping any ODUk over ODUCn with 5G TSG."
}
]
}
}
]
}
Authors' Addresses
Zheng & Busi Expires September 10, 2020 [Page 38]
Internet-Draft A YANG Data Model for Layer 1 Types March 2020
Haomian Zheng
Huawei Technologies
H1, Huawei Industrial Base, Songshanhu
Dongguan, Guangdong 523808
China
Email: zhenghaomian@huawei.com
Italo Busi
Huawei Technologies
Milan
Italy
Email: Italo.Busi@huawei.com
Zheng & Busi Expires September 10, 2020 [Page 39]