CCAMP Working Group Xian Zhang
Internet-Draft Haomian Zheng
Intended status: Standards Track Huawei
Ramon Casellas
CTTC
O. Gonzalez de Dios
Telefonica
D. Ceccarelli
Ericsson
Expires: April 13, 2016 October 16, 2015
GMPLS OSPF-TE Extensions in support of Flexi-grid DWDM networks
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt
Abstract
This memo describes the OSPF-TE extensions in support of GMPLS
control of networks that include devices that use the new flexible
optical grid.
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with
the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on April 13, 2016.
Copyright Notice
Zhang et al Expires April 2016 [Page 1]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
Copyright (c) 2015 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction ................................................ 2
2. Terminology ................................................. 3
2.1. Conventions Used in this Document .......................3
3. Requirements for Flexi-grid Routing ..........................3
3.1. Available Frequency Ranges ..............................4
3.2. Application Compliance Considerations ...................5
3.3. Comparison with Fixed-grid DWDM Links ...................6
4. Extensions .................................................. 7
4.1. ISCD Extensions for Flexi-grid ..........................7
4.1.1. Switching Capability Specific Information (SCSI) .... 7
4.1.2. An SCSI Example.................................... 9
4.2. Extensions to Port Label Restriction sub-TLV ...........12
5. IANA Considerations ........................................ 13
5.1. New Switching Type..................................... 13
5.2. New Sub-TLV ........................................... 13
6. Implementation Status....................................... 13
6.1. Centre Tecnologic de Telecomunicacions de Catalunya (CTTC)14
7. Acknowledgments ............................................ 15
8. Security Considerations..................................... 15
9. Contributors' Addresses..................................... 15
10. References ................................................ 16
10.1. Normative References.................................. 16
10.2. Informative References................................ 16
1. Introduction
[G.694.1] defines the Dense Wavelength Division Multiplexing (DWDM)
frequency grids for Wavelength Division Multiplexing (WDM)
applications. A frequency grid is a reference set of frequencies
used to denote allowed nominal central frequencies that may be used
Zhang et al Expires April 2016 [Page 2]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
for defining applications. The channel spacing is the frequency
spacing between two allowed nominal central frequencies. All of the
wavelengths on a fiber should use different central frequencies and
occupy a fixed bandwidth of frequency.
Fixed grid channel spacing is selected from 12.5 GHz, 25 GHz, 50 GHz,
100 GHz and integer multiples of 100 GHz. But [G.694.1] also
defines "flexible grids", also known as "flexi-grid". The terms
"frequency slot" (i.e., the frequency range allocated to a specific
channel and unavailable to other channels within a flexible grid)
and "slot width" (i.e., the full width of a frequency slot in a
flexible grid) are used to define a flexible grid.
[FLEX-FWK] defines a framework and the associated control plane
requirements for the GMPLS based control of flexi-grid DWDM networks.
[RFC6163] provides a framework for GMPLS and Path Computation
Element (PCE) control of Wavelength Switched Optical Networks
(WSONs), and [WSON-OSPF] defines the requirements and OSPF-TE
extensions in support of GMPLS control of a WSON.
[FLEX-SIG] describes requirements and protocol extensions for
signaling to set up LSPs in networks that support the flexi-grid,
and this document complements [FLEX-SIG] by describing the
requirement and extensions for OSPF-TE routing in a flexi-grid
network.
This draft compliments the efforts to provide extensions to Open
Short Path First (OSPF) Traffic-Engineering (TE) protocol so as to
support GMPLS control of flexi-grid networks.
2. Terminology
For terminology related to flexi-grid, please consult [FLEX-FWK] and
[G.694.1].
2.1. Conventions Used in this Document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [RFC2119].
3. Requirements for Flexi-grid Routing
The architecture for establishing LSPs in a Spectrum Switched
optical Network (SSON) is described in [FLEX-FWK].
Zhang et al Expires April 2016 [Page 3]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
A flexi-grid LSP occupies a specific frequency slot, i.e. a range of
frequencies. The process of computing a route and the allocation of
a frequency slot is referred to as RSA (Routing and Spectrum
Assignment). [FLEX-FWK] describes three types of architectural
approaches to RSA: combined RSA; separated RSA; and distributed SA.
The first two approaches among them could be called "centralized SA"
because the spectrum (frequency slot) assignment is performed by a
single entity before the signaling procedure.
In the case of centralized SA, the assigned frequency slot is
specified in the RSVP-TE Path message during the signaling process.
In the case of distributed SA, only the requested slot width of the
flexi-grid LSP is specified in the Path message, allowing the
involved network elements to select the frequency slot to be used.
If the capability of switching or converting the whole optical
spectrum allocated to an optical spectrum LSP is not available at
nodes along the path of the LSP, the LSP is subject to the Optical
"Spectrum Continuity Constraint", as described in [FLEX-FWK].
The remainder of this section states the additional extensions on
the routing protocols in a flexi-grid network. That is, the
additional information that must be collected and passed between
nodes in the network by the routing protocols in order to enable
correct path computation and signaling in support of LSPs within the
network.
3.1. Available Frequency Ranges
In the case of flexi-grids, the central frequency steps from 193.1
THz with 6.25 GHz granularity. The calculation method of central
frequency and the frequency slot width of a frequency slot are
defined in [G.694.1], i.e., by using nominal central frequency n and
the slot width m.
On a DWDM link, the allocated or in-use frequency slots must not
overlap with each other. However, the border frequencies of two
frequency slots may be the same frequency, i.e., the highest
frequency of a frequency slot may be the lowest frequency of the
next frequency slot.
Zhang et al Expires April 2016 [Page 4]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
Frequency Slot 1 Frequency Slot 2
+-----------+-----------------------+
| | |
-9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11
...+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--...
------------ ------------------------
^ ^
Central F = 193.1THz Central F = 193.1375 THz
Slot width = 25 GHz Slot width = 50 GHz
Figure 1 - Two Frequency Slots on a Link
Figure 1 shows two adjacent frequency slots on a link. The highest
frequency of frequency slot 1 denoted by n=2 is the lowest frequency
of slot 2. In this example, it means that the frequency range from
n=-2 to n=10 is occupied and is unavailable to other flexi-grid LSPs.
Hence, in order to clearly show which LSPs can be supported and what
frequency slots are unavailable, the available frequency ranges MUST
be advertised by the routing protocol for the flexi-grid DWDM links.
A set of non-overlapping available frequency ranges MUST be
disseminated in order to allow efficient resource management of
flexi-grid DWDM links and RSA procedures which are described in
Section 4.8 of [FLEX-FWK].
3.2. Application Compliance Considerations
As described in [G.694.1], devices or applications that make use of
the flexi-grid may not be capable of supporting every possible slot
width or position (i.e., central frequency). In other words,
applications or implementations may be defined where only a subset
of the possible slot widths and positions are required to be
supported.
For example, an application could be defined where the nominal
central frequency granularity is 12.5 GHz (by only requiring values
of n that are even) and that only requires slot widths as a multiple
of 25 GHz (by only requiring values of m that are even).
Hence, in order to support all possible applications and
implementations the following information should be advertised for a
flexi-grid DWDM link:
o Chanel Spacing (C.S.): as defined in [FLEX-LBL] and for flexi-
grid, is set to 5 to denote 6.25GHz.
Zhang et al Expires April 2016 [Page 5]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
o Central frequency granularity: a multiplier of C.S..
o Slot width granularity: a multiplier of 2*C.S..
o Slot width range: two multipliers of the slot width granularity,
each indicate the minimal and maximal slot width supported by a
port respectively.
The combination of slot width range and slot width granularity can
be used to determine the slot widths set supported by a port.
3.3. Comparison with Fixed-grid DWDM Links
In the case of fixed-grid DWDM links, each wavelength has a pre-
defined central frequency and each wavelength maps to a pre-defined
central frequency and the usable frequency range is implicit by the
channel spacing. All the wavelengths on a DWDM link can be
identified with an identifier that mainly convey its central
frequency as the label defined in [RFC6205], and the status of the
wavelengths (available or not) can be advertised through a routing
protocol.
Figure 2 shows a link that supports a fixed-grid with 50 GHz channel
spacing. The central frequencies of the wavelengths are pre-defined
by values of "n" and each wavelength occupies a fixed 50 GHz
frequency range as described in [G.694.1].
W(-2) | W(-1) | W(0) | W(1) | W(2) |
...---------+-----------+-----------+-----------+-----------+----...
| 50 GHz | 50 GHz | 50 GHz | 50 GHz |
n=-2 n=-1 n=0 n=1 n=2
...---+-----------+-----------+-----------+-----------+----------...
^
Central F = 193.1THz
Figure 2 - A Link Supports Fixed Wavelengths with 50 GHz Channel
Spacing
Unlike the fixed-grid DWDM links, on a flexi-grid DWDM link the slot
width of the frequency slot is flexible as described in section 3.1.
That is, the value of m in the following formula [G.694.1] is
uncertain before a frequency slot is actually allocated for a flexi-
grid LSP.
Zhang et al Expires April 2016 [Page 6]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
Slot Width (GHz) = 12.5GHz * m
For this reason, the available frequency slot/ranges need to be
advertised for a flexi-grid DWDM link instead of the specific
"wavelengths" points that are sufficient for a fixed-grid link.
Moreover, thus advertisement is represented by the combination of
Central Frequency Granularity and Slot Width Granularity.
4. Extensions
As described in [FLEX-FWK], the network connectivity topology
constructed by the links/nodes and node capabilities are the same as
for WSON, and can be advertised by the GMPLS routing protocols
(refer to section 6.2 of [RFC6163]). In the flexi-grid case, the
available frequency ranges instead of the specific "wavelengths" are
advertised for the link. This section defines the GMPLS OSPF-TE
extensions in support of advertising the available frequency ranges
for flexi-grid DWDM links.
4.1. ISCD Extensions for Flexi-grid
Value Type
----- ----
152 (TBA by IANA) Flexi-Grid-LSC capable
Switching Capability and Encoding values MUST be used as follows:
Switching Capability = Flexi-Grid-LSC
Encoding Type = lambda [as defined in RFC3471]
When Switching Capability and Encoding fields are set to values as
stated above, the Interface Switching Capability Descriptor MUST be
interpreted as in [RFC4203] with the optional inclusion of one or
more Switching Capability Specific Information sub-TLVs.
4.1.1. Switching Capability Specific Information (SCSI)
The technology specific part of the Flexi-grid ISCD should include
the available frequency spectrum resource as well as the max slot
widths per priority information. The format of this flex-grid SCSI,
the frequency available bitmap TLV, is depicted in the following
figure:
Zhang et al Expires April 2016 [Page 7]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 1 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Priority | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max Slot Width at Priority 0 | ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Max Slot Width at Priority 7 | Unreserved padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| C.S. | Starting n | No. of Effective. Bits|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Bit Map ... ~
~ ... | padding bits ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type (16 bits): The type of this sub-TLV and is set to 1.
Length (16 bits): The length of the value field of this sub-TLV.
Priority (8 bits): A bitmap used to indicate which priorities
are being advertised. The bitmap is in ascending order, with the
leftmost bit representing priority level 0 (i.e., the highest) and
the rightmost bit representing priority level 7 (i.e., the
lowest). A bit MUST be set (1) corresponding to each priority
represented in the sub-TLV, and MUST NOT be set (0) when the
corresponding priority is not represented. At least one priority
level MUST be advertised that, unless overridden by local policy,
SHALL be at priority level 0.
Max Slot Width (16 bits): This field indicates maximal frequency
slot width supported at a particular priority level. This field
MUST be set to max frequency slot width supported in the unit of
2.C.S., for a particular priority level. One field MUST be present
for each bit set in the Priority field, and is ordered to match the
Priority field. Fields MUST NOT be present for priority levels that
are not indicated in the Priority field.
Unreserved Padding (16 bits): The Padding field is used to
ensure the 32 bit alignment of Max Slot Width fields. When
present the Unreserved Padding field is 16 bits (2 byte) long.
When the number of priorities is odd, the Unreserved Padding field
MUST be included. When the number of priorities is even, the
Unreserved Padding MUST be omitted.
Zhang et al Expires April 2016 [Page 8]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
C.S. (4 bits): As defined in [FLEX-LBL] and it is currently set to 5.
Starting n (16 bits): as defined in [FLEX-LBL] and this value
denotes the starting nominal central frequency point of the
frequency availability bitmap sub-TLV.
Number of Effective Bits (12 bits): Indicates the number of
effective bits in the Bit Map field.
Bit Map (variable): Indicates whether a basic frequency slot,
characterized by a nominal central frequency and a fixed m value of
1, is available or not for flexi-grid LSP setup. The first nominal
central frequency is the value of starting n and with the subsequent
ones implied by the position in the bitmap. Note that when setting
to 1, it means that the corresponding central frequency is available
for a flexi-grid LSP with m=1. Note that a centralized SA process
will need to extend this to high values of m by checking a
sufficient large number of consecutive basic frequency slots that
are available.
Padding Bits (variable): Added after the Bit Map to make it a
multiple of four bytes if necessary. Padding bits MUST be set to 0
and MUST be ignored on receipt.
The Reserved field MUST be set to zero on transmission and SHOULD be
ignored on receipt.
The starting n MAY be set to the lowest possible nominal central
frequency supported by the link. An example is provided in the next
section.
4.1.2. An SCSI Example
Figure 3 shows an example of the available frequency spectrum
resource of a flexi-grid DWDM link.
-9 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11
...+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--...
|--Available Frequency Range--|
Figure 3 - Flexi-grid DWDM Link Example
The symbol "+" represents the allowed nominal central frequency. The
symbol "--" represents a central frequency granularity of 6.25 GHz,
as currently be standardized in [G.694.1]. The number on the top of
the line represents the "n" in the frequency calculation formula
Zhang et al Expires April 2016 [Page 9]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
(193.1 + n * 0.00625). The nominal central frequency is 193.1 THz
when n equals zero.
In this example, it is assumed that the lowest nominal central
frequency supported is n= -9 and the highest is n=11. Note they
cannot be used as a nominal central frequency for setting up a LSP,
but merely as the way to express the supported frequency range.
Using the encoding defined in Section 4.1.1, the relevant fields to
express the frequency resource availability can be filled as below:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 1 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Priority | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max Slot Width at Priority 0 | ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Max Slot Width at Priority 7 | Unreserved padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5 | Starting n (-9) | No. of Effec. Bits(21)|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|0|0|0|0|0|0|1|1|1|1|1|1|1|1|1|0|0|0|0| padding bits (0s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
In the above example, the starting n is selected to be the lowest
nominal central frequency, i.e. -9. Note other starting n values can
be chosen and for example, the first available nominal central
frequency (a.k.a., the first available basic frequency slot) can be
chosen and the SCSI will be expressed as the following:
Zhang et al Expires April 2016 [Page 10]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 1 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Priority | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max Slot Width at Priority 0 | ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Max Slot Width at Priority 7 | Unreserved padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5 | Starting n (-1) | No. of Effec. Bits(9)|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|1|1|1|1|1|1|1|1|1| padding bits (0s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This denotes that other than the advertised available nominal
central frequencies, the other nominal central frequencies within
the whole frequency range supported by the link are not available
for path computation use.
If a LSP with slot width (m) equal to 1 is set up using this link,
say using n= -1, then the SCSI information is updated to be the
following:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = 1 | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Priority | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Max Slot Width at Priority 0 | ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ Max Slot Width at Priority 7 | Unreserved padding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 5 | Starting n (-1) | No. of Effec. Bits(9)|
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|0|0|1|1|1|1|1|1|1| padding bits (0s) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Zhang et al Expires April 2016 [Page 11]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
4.2. Extensions to Port Label Restriction sub-TLV
As described in Section 3.2, a port that supports flexi-grid may
support only a restricted subset of the full flexible grid. The
Port Label Restriction sub-TLV is defined in [RFC7579]. It can be
used to describe the label restrictions on a port and is carried in
the top-level Link TLV as specified in [RFC7580]. A new restriction
type, the flexi-grid Restriction Type, is defined here to specify
the restrictions on a port to support flexi-grid.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MatrixID | RstType = 5 | Switching Cap | Encoding |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| C.S. | C.F.G | S.W.G | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Min Slot Width | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
MatrixID (8 bits): As defined in [RFC7579].
RstType (Restriction Type, 8 bits): Takes the value of 5 to indicate
the restrictions on a port to support flexi-grid.
Switching Cap (Switching Capability, 8 bits): As defined in
[RFC7579], MUST be consistent with the one specified in ISCD as
described in Section 4.1.
Encoding (8 bits): As defined in [RFC7579], must be consistent with
the one specified in ISCD as described in Section 4.1.
C.S. (4 bits): As defined in [FLEX-LBL] and for flexi-grid is 5 to
denote 6.25GHz.
C.F.G (Central Frequency Granularity, 8 bits): A positive integer.
Its value indicates the multiple of C.S., in terms of central
frequency granularity.
S.W.G (Slot Width Granularity, 8 bits): A positive integer. Its
value indicates the multiple of 2*C.S., in terms of slot width
granularity.
Min Slot Width (16 bits): A positive integer. Its value indicates
the multiple of 2*C.S. (GHz), in terms of the supported minimal slot
width.
Zhang et al Expires April 2016 [Page 12]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
The Reserved field MUST be set to zero on transmission and SHOULD be
ignored on receipt.
5. IANA Considerations
5.1. New Switching Type
Upon approval of this document, IANA will make the assignment in the
"Switching Types" section of the "GMPLS Signaling Parameters"
registry located at http://www.iana.org/assignments/gmpls-sig-
parameters:
Value Name Reference
--------- -------------------------- ----------
152 (*) Flexi-Grid-LSC capable [This.I-D]
(*) Suggested value
5.2. New Sub-TLV
This document defines one new sub-TLV that are carried in the
Interface Switching Capability Descriptors [RFC4203] with Signal
Type Flexi-Grid-LSC capable.
Upon approval of this document, IANA will create and maintain a new
sub-registry, the "Types for sub-TLVs of Flexi-Grid-LSC capable SCSI
(Switch Capability-Specific Information)" registry under the "Open
Shortest Path First (OSPF) Traffic Engineering TLVs" registry, see
http://www.iana.org/assignments/ospf-traffic-eng-tlvs/ospf-traffic-
eng-tlvs.xml, with the sub-TLV types as follows:
This document defines new sub-TLV types as follows:
Value Sub-TLV Reference
--------- -------------------------- ----------
0 Reserved [This.I-D]
1 Frequency availability bitmap [This.I-D]
6. Implementation Status
[RFC Editor Note: Please remove this entire section prior to
publication as an RFC.]
Zhang et al Expires April 2016 [Page 13]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
This section records the status of known implementations of the
protocol defined by this specification at the time of posting of
this Internet-Draft, and is based on a proposal described in RFC
6982[RFC6982]. The description of implementations in this section
is intended to assist the IETF in its decision processes in
progressing drafts to RFCs. Please note that the listing of any
individual implementation here does not imply endorsement by the
IETF. Furthermore, no effort has been spent to verify the
information presented here that was supplied by IETF contributors.
This is not intended as, and must not be construed to be, a catalog
of available implementations or their features. Readers are advised
to note that other implementations may exist.
According to RFC 6982, "this will allow reviewers and working groups
to assign due consideration to documents that have the benefit of
running code, which may serve as evidence of valuable
experimentation and feedback that have made the implemented
protocols more mature. It is up to the individual working groups to
use this information as they see fit.
6.1. Centre Tecnologic de Telecomunicacions de Catalunya (CTTC)
Organization Responsible for the Implementation: CTTC - Centre
Tecnologic de Telecomunicacions de Catalunya (CTTC), Optical
Networks and Systems Department, http://wikiona.cttc.es.
Implementation Name and Details: ADRENALINE testbed,
http://networks.cttc.es/experimental-testbeds/
Brief Description: Experimental testbed implementation of
GMPLS/PCE control plane.
Level of Maturity: Implemented as extensions to a mature
GMLPS/PCE control plane. It is limited to research / prototyping
stages but it has been used successfully for more than the last five
years.
Coverage: Support for the 64 bit label [FLEC-LBL] for flexi-grid
as described in this document, with available label set encoded as
bitmap.
It is expected that this implementation will evolve to follow the
evolution of this document.
Zhang et al Expires April 2016 [Page 14]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
Licensing: Proprietary
Implementation Experience: Implementation of this document
reports no issues. General implementation experience has been
reported in a number of journal papers. Contact Ramon Casellas for
more information or see http://networks.cttc.es/publications/?
search=GMPLS&research_area=optical-networks-systems
Contact Information: Ramon Casellas: ramon.casellas@cttc.es
Interoperability: No report.
7. Acknowledgments
This work was supported in part by the FP-7 IDEALIST project under
grant agreement number 317999.
This work was supported in part by NSFC Project 61201260.
8. Security Considerations
This document extends [RFC4203] and [RFC7580] to carry flex-grid
specific information in OSPF Opaque LSAs. This document does not
introduce any further security issues other than those discussed in
[RFC3630], [RFC4203]. To be more specific, the security mechanisms
described in [RFC2328] which apply to Opaque LSAs carried in OSPF
still apply. An analysis of the OSPF security is provided in
[RFC6863] and applies to the extensions to OSPF in this document as
well.
9. Contributors' Addresses
Adrian Farrel
Old Dog Consulting
Email: adrian@olddog.co.uk
Fatai Zhang
Huawei Technologies
Email: zhangfatai@huawei.com
Zhang et al Expires April 2016 [Page 15]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
Lei Wang,
ZTE
Email: wang.lei31@zte.com.cn
Guoying Zhang,
China Academy of Telecom Research
Email: zhangguoying@ritt.cn
10. References
10.1. Normative References
[RFC2119] S. Bradner, "Key words for use in RFCs to indicate
requirements levels", RFC 2119, March 1997.
[G.694.1] ITU-T Recommendation G.694.1 (revision 2), "Spectral grids
for WDM applications: DWDM frequency grid", February 2012.
[RFC7579] Bernstein, G., Lee, Y., Li, D., and W. Imajuku, "General
Network Element Constraint Encoding for GMPLS Controlled
Networks", RFC 7579, June 2015.
[RFC7580] F. Zhang, Y. Lee, J. Han, G. Bernstein and Y. Xu, "OSPF-TE
Extensions for General Network Element Constraints ", RFC
7580, June 2015.
[RFC6205] T. Otani and D. Li, "Generalized Labels for Lambda-Switch-
Capable (LSC) Label Switching Routers", RFC 6205, March
2011.
[FLEX-LBL] King, D., Farrel, A. and Y. Li, "Generalized Labels for
the Flexi-Grid in Lambda Switch Capable (LSC) Label
Switching Routers", draft-ietf-ccamp-flexigrid-lambda-
label, work in progress.
10.2. Informative References
[RFC6163] Y. Lee, G. Bernstein and W. Imajuku, "Framework for GMPLS
and Path Computation Element (PCE) Control of Wavelength
Switched Optical Networks (WSONs)", RFC 6163, April 2011.
[FLEX-SIG] F.Zhang et al, "RSVP-TE Signaling Extensions in support
of Flexible-grid", draft-ietf-ccamp-flexible-grid-rsvp-te-
ext, work in progress.
Zhang et al Expires April 2016 [Page 16]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
[FLEX-FWK] Gonzalez de Dios, O., Casellas R., Zhang, F., Fu, X.,
Ceccarelli, D., and I. Hussain, "Framework and
Requirements for GMPLS based control of Flexi-grid DWDM
networks', draft-ietf-ccamp-flexi-grid-fwk, work in
progress.
[WSON-OSPF] Y. Lee and G. Bernstein, "GMPLS OSPF Enhancement for
Signal and Network Element Compatibility for Wavelength
Switched Optical Networks ", draft-ietf-ccamp-wson-signal-
compatibility-ospf, work in progress.
[RFC2328] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998.
[RFC6863] Hartman, S. and D. Zhang, "Analysis of OSPF Security
According to the Keying and Authentication for Routing
Protocols (KARP) Design Guide", RFC 6863, March 2013.
Authors' Addresses
Xian Zhang
Huawei Technologies
Email: zhang.xian@huawei.com
Haomian Zheng
Huawei Technologies
Email: zhenghaomian@huawei.com
Ramon Casellas, Ph.D.
CTTC
Spain
Phone: +34 936452916
Email: ramon.casellas@cttc.es
Oscar Gonzalez de Dios
Telefonica Investigacion y Desarrollo
Emilio Vargas 6
Madrid, 28045
Spain
Phone: +34 913374013
Email: ogondio@tid.es
Daniele Ceccarelli
Ericsson
Via A. Negrone 1/A
Genova - Sestri Ponente
Italy
Zhang et al Expires April 2016 [Page 17]
draft-ietf-ccamp-flexible-grid-ospf-ext-03.txt October 2015
Email: daniele.ceccarelli@ericsson.com
Zhang et al Expires April 2016 [Page 18]