Network Working Group Y. Cui
Internet-Draft J. Wu
Intended status: Standards Track P. Wu
Expires: January 9, 2012 Tsinghua University
C. Metz
Cisco Systems, Inc.
O. Vautrin
Juniper Networks
Y. Lee
Comcast
July 8, 2011
Public IPv4 over Access IPv6 Network
draft-cui-softwire-host-4over6-06
Abstract
This draft proposes a mechanism for bidirectional IPv4 communication
between IPv4 Internet and end hosts or IPv4 networks sited in IPv6
access network. This mechanism follows the softwire hub and spoke
model and uses IPv4-over-IPv6 tunnel as basic method to traverse IPv6
network. By allocating public IPv4 addresses to end hosts/networks
in IPv6, it can achieve IPv4 end-to-end bidirectional communication
between these hosts/networks and IPv4 Internet. This mechanism is an
IPv4 access method for hosts and IPv4 networks sited in IPv6.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on January 9, 2012.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
Cui, et al. Expires January 9, 2012 [Page 1]
Internet-Draft Public 4over6 July 2011
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Requirements language . . . . . . . . . . . . . . . . . . . . 4
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 5
4. Deployment scenario . . . . . . . . . . . . . . . . . . . . . 6
4.1. Scenario and requirements . . . . . . . . . . . . . . . . 6
4.2. Use cases . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Public 4over6 Mechanism . . . . . . . . . . . . . . . . . . . 9
5.1. Address allocation and mapping maintenance . . . . . . . . 9
5.2. 4over6 initiator behavior . . . . . . . . . . . . . . . . 9
5.2.1. Host initiator . . . . . . . . . . . . . . . . . . . . 10
5.2.2. CPE initiator . . . . . . . . . . . . . . . . . . . . 10
5.3. 4over6 concentrator behavior . . . . . . . . . . . . . . . 11
6. Technical advantages . . . . . . . . . . . . . . . . . . . . . 12
7. Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . 13
8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8.1. Normative References . . . . . . . . . . . . . . . . . . . 14
8.2. Informative References . . . . . . . . . . . . . . . . . . 14
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 16
Cui, et al. Expires January 9, 2012 [Page 2]
Internet-Draft Public 4over6 July 2011
1. Introduction
Global IPv4 addresses are running out fast. Meanwhile, the demand
for IP address is still growing and may even burst in potential
circumstances like "Internet of Things". To satisfy the end users,
operators have to push IPv6 to the front, by building IPv6 networks
and providing IPv6 services.
When IPv6-only networks are widely deployed, users of those networks
will probably still need IPv4 connectivity. This is because part of
Internet will stay IPv4-only for a long time, and network users in
IPv6-only networks will communicate with network users sited in the
IPv4-only part of Internet. This demand could eventually decrease
with the general IPv6 adoption.
Network operators should provide IPv4 services to IPv6 users to
satisfy their demand, usually through tunnels. This type of IPv4
services differ in provisioned IPv4 addresses. If the users can't
get public IPv4 addresses (e.g., new network users join an ISP which
don't have enough unused IPv4 addresses), they have to use private
IPv4 addresses on the client side, and IPv4-private-to-public
translation is required on the carrier side, as is described in Dual-
stack Lite[I-D.ietf-softwire-dual-stack-lite]. Otherwise the users
can get public IPv4 addresses, and use them for IPv4 communication.
In this case, translation on the carrier side won't be necessary.
The network users and operators can avoid all the issues raised by
translation, such as ALG, NAT traversal, state maintenance, etc.
Note that this "public IPv4" situation is actually quite common.
There're approximatively 2^32 network users who are using or can
potentially get public IPv4 addresses. Most of them will switch to
IPv6 sooner or later, and will require IPv4 services for a
significant period after the switching. This draft focuses on this
situation, i.e., to provide IPv4 access for users in IPv6 networks,
where public IPv4 addresses are still available for allocation.
Cui, et al. Expires January 9, 2012 [Page 3]
Internet-Draft Public 4over6 July 2011
2. Requirements language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Cui, et al. Expires January 9, 2012 [Page 4]
Internet-Draft Public 4over6 July 2011
3. Terminology
Public 4over6: Public 4over6 is the mechanism proposed by this draft.
Generally, Public 4over6 supports bidirectional communication between
IPv4 Internet and IPv4 hosts or local networks in IPv6 access
network, by leveraging IPv4-in-IPv6 tunnel and public IPv4 address
allocation.
4over6 initiator: in Public 4over6 mechanism, 4over6 initiator is the
IPv4-in-IPv6 tunnel initiator located on the user side of IPv6
network. The 4over6 initiator can be either a dual-stack capable
host or a dual-stack CPE device. In the former case, the host has
both IPv4 and IPv6 stack but is provisioned with IPv6 access only.
In the latter case, the CPE has both IPv6 interface for access to ISP
network and IPv4 interface for local network connection; hosts in the
local network can be IPv4-only.
4over6 concentrator: in Public 4over6 mechanism, 4over6 concentrator
is the IPv4-in-IPv6 tunnel concentrator located in IPv6 ISP network.
It's a dual-stack router which connects to both the IPv6 network and
IPv4 Internet.
Cui, et al. Expires January 9, 2012 [Page 5]
Internet-Draft Public 4over6 July 2011
4. Deployment scenario
4.1. Scenario and requirements
The general scenario of Public 4over6 is shown in Figure 1. Users in
an IPv6 network take IPv6 as their native service. Some users are
end hosts which face the ISP network directly, while others are local
networks behind CPEs, such as a home LAN, an enterprise network, etc.
The ISP network is IPv6-only rather than dual-stack, which means that
ISP can't provide native IPv4 access to its users; however, it's
acceptable that one or more routers on the carrier side become dual-
stack and get connected to IPv4 Internet. So if network users want
to connect to IPv4, these dual-stack routers will be their
"entrances".
+-------------------------+
| IPv6 ISP Network |
+------+ |
|host: | |
|initi-| |
|ator |=================+-------+ +-----------+
+------+ |4over6 | | IPv4 |
| IPv4-in-IPv6 |Concen-|---| Internet |
+----------+ +------+ |trator | | |
|local IPv4|--|CPE: |=================+-------+ +-----------+
| network | |initi-| |
+----------+ |ator | |
+------+ |
| |
+-------------------------+
Figure 1 Public 4over6 scenario
Before getting into any technical details, the communication
requirements should be stated. The first one is that, 4over6 users
require IPv4-to-IPv4 communication with the IPv4 Internet. An IPv4
access service is needed rather than an IPv6-to-IPv4 translation
service. (IPv6-to-IPv4 communication is out of the scope of this
draft.)
Second, 4over6 users require public IPv4 addresses rather than
private addresses. Public IPv4 address means there's no IPv4 CGN
along the path, so the acquired IPv4 service is better. In
particular, some hosts may be application servers, public address
works better for reasons like straightforward access, direct DNS
registration, no stateful mapping maintenance on CGN, etc. For the
Cui, et al. Expires January 9, 2012 [Page 6]
Internet-Draft Public 4over6 July 2011
direct-connected host case, each host should get one public IPv4
address. For the local IPv4 network case, the CPE can get a public
IPv4 address and runs an IPv4 NAT for the local network. Here a
local NAT is still much better than the situation that involves a
CGN, since this NAT is in local network and can be configured and
managed by the users.
Third, translation is not preferred in this scenario. If this IPv4-
to-IPv4 communication is achieved by IPv4-IPv6 translation, it'll
need double translation along the path, one from IPv4 to IPv6 and the
other from IPv6 back to IPv4. This would be quite complicated,
especially in addressing. Contrarily a tunnel can achieve the IPv4-
over-IPv6 traversing easily. That's the reason this draft follows
the hub and spoke softwire model.
Moreover, the ISP probably would like to keep their IPv4 and IPv6
addressing and routing separated when provisioning IPv4 over IPv6.
Then the ISP can manage the native IPv6 network more easily and
independently, and also provision IPv4 in a flexible, on-demand way.
The cost is that the concentrator needs to maintain per-user address
mapping state, which would be described in detail.
4.2. Use cases
Public 4over6 can be applicable in several practical cases. The
first one is that ISPs which still own enough IPv4 addresses switch
to IPv6. The ISPs can deploy public 4over6 to preserve IPv4 service
for the customers. This case is actually quite common. The majority
of the wired end users today get Internet access with public IPv4
address. When their ISPs switch to IPv6, these users can still use
the same amount of IPv4 addresses for IPv4 access. Public 4over6 can
leveraging these addresses and offer tunneled IPv4 access.
The second case is ISPs which don't have enough IPv4 addresses any
more switch to IPv6. For these ISPs, dual-stack lite is so far the
most mature solution to provision IPv4 over IPv6. In dual-stack
lite, end users use private IPv4 addresses, experience a 44CGN and
hence some service degradation. As long as the end users use public
IPv4 addresses, all CGN issues can be avoided and the IPv4 service
can be full bi-directional. In other words, Public 4over6 can be
deployed along with DS-lite, to provide a value-added service.
Common users adopt DS-lite to communicate with IPv4 while high-end
users adopt Public 4over6. The two mechanisms can actually be
coupled easily.
There is also a special situation in the second case that the end
users are IPv4 application servers. In this situation, public
address brings significant convenience. The DNS registration can be
Cui, et al. Expires January 9, 2012 [Page 7]
Internet-Draft Public 4over6 July 2011
direct using dedicated address; the access of application clients can
be straightforward with no translation; there's no need to reserve
and maintain address mapping on the CGN, and no well-known port
collision will come up. So it's better to have servers adopt Public
4over6 for IPv4 access when they're located in IPv6 network.
Following the principle of Public 4over6, it's also possible to
achieve address multiplexing and save IPv4 addresses. There're
already efforts on this subject, see
[I-D.cui-softwire-b4-translated-ds-lite] and [I-D.sun-v6ops-laft6].
The basic idea is that instead of allocating a full IPv4 address to
every end user, the ISP can allocate an IPv4 address with restricted
port range to every end user.
Besides, the draft would like to be explicit about the scope of
direct-connected host case and CPE case. The host case is clear: the
host is directly connected to IPv6 network, but the protocol stack on
the host support IPv4 too. As to the CPE case, this draft would like
to only focus on the case that the local network behind the CPE is
private IPv4. If the users want to run public IPv4 into the local
network, then they can either run dual-stack in the local network and
turn into host case(likely home LAN situation), or they can acquire
address blocks from the ISP and build configured tunnel or softwire
mesh[RFC5565] with the ISP network(likely enterprise network
situation). TC can be implemented to be compatible with the latter
case too, though.
Cui, et al. Expires January 9, 2012 [Page 8]
Internet-Draft Public 4over6 July 2011
5. Public 4over6 Mechanism
5.1. Address allocation and mapping maintenance
Public 4over6 can be generally considered as IPv4-over-IPv6 hub and
spoke tunnel using public IPv4 address. Each 4over6 initiator will
use public IPv4 address for IPv4-over-IPv6 communication. As is
described above, in the host initiator case, every host will get one
IPv4 address; in the CPE case, every CPE will get one IPv4 address,
which will be shared by hosts behind the CPE. The key problem here
is IPv4 address allocation over IPv6 network, from ISP device(s) to
separated 4over6 initiators.
There're two possibilities here. One is DHCPv4 over IPv6, and the
other is static configuration. DHCPv4 over IPv6 is achieved by
performing DHCPv4 on IPv4-in-IPv6 tunnel between ISP device and
4over6 initiators. There do exist the DHCP encapsulation issue on
server side, see details and solutions in
[I-D.cui-softwire-dhcp-over-tunnel]. As to static configuration,
4over6 users and the ISP operators should negotiate beforehand to
authorize the IPv4 address. Application servers usually falls into
this case. Public 4over6 supports both address allocation manners.
Actually, it is transparent to address allocation methods.
Along with IPv4 address allocation, Public 4over6 should maintain the
IPv4-IPv6 address mappings on the concentrator. In this type of
address mapping, the IPv4 address is the public IPv4 address
allocated to a 4over6 initiator, and the IPv6 addresses is the
initiator's IPv6 address. This mapping is used to provide correct
encapsulation destination address for the concentrator.
The initiator sends "pinhole" packets to the concentrator
periodically, to install and renew the address mapping. A pinhole
packet is an IPv4-in-IPv6 packet, which uses the concentrator's IPv6
address as destination IPv6 address, the initiator's IPv6 address as
source IPv6 address, and the initiator's IPv4 address as source IPv4
address. When the concentrator receives such a packet, it'll resolve
the IPv4 and IPv6 address information from the packet and trigger the
mapping. Since any IPv4-in-IPv6 data packet from the initiator
contains these exact informations, it can also serve as pinhole
packet. Then dedicated pinhole packets are sent out when there's no
data packets. Another possible way to maintain the address mapping
is to run PCP[I-D.ietf-pcp-base] while extending the protocol to
support applying for a full address. The following sections describe
the mechanism with the pinhole method.
5.2. 4over6 initiator behavior
Cui, et al. Expires January 9, 2012 [Page 9]
Internet-Draft Public 4over6 July 2011
4over6 initiator has an IPv6 interface connected to the IPv6 ISP
network, and a tunnel interface to support IPv4-in-IPv6
encapsulation. In CPE case, it has at least one IPv4 interface
connected to IPv4 local network.
4over6 initiator should learn the 4over6 concentrator's IPv6 address
beforehand. For example, if the initiator gets its IPv6 address by
DHCPv6, it can get the 4over6 concentrator's IPv6 address through a
DHCPv6 option[I-D.ietf-softwire-ds-lite-tunnel-option].
5.2.1. Host initiator
When the initiator is a direct-connected host, it assigns the
allocated public IPv4 address to its tunnel interface. The host uses
this address for IPv4 communication. If this address is allocated
through DHCP, the host should support DHCPv4 over tunnel. After the
allocation, the host periodically sends pinhole packet to the
concentrator to install the address mapping and keep it alive.
For IPv4 data traffic, the host performs the IPv4-in-IPv6
encapsulation and decapsulation on the tunnel interface. When
sending out an IPv4 packet, it performs the encapsulation, using the
IPv6 address of the 4over6 concentrator as the IPv6 destination
address, and its own IPv6 address as the IPv6 source address. The
encapsulated packet will be forwarded to the IPv6 network. The
decapsulation on 4over6 initiator is simple. When receiving an IPv4-
in-IPv6 packet, the initiator just drops the IPv6 header, and hands
it to upper layer.
5.2.2. CPE initiator
The CPE case is quite similar to the host initiator case. The CPE
assign the allocated IPv4 address to its tunnel interface. The local
IPv4 network won't take part in the public IPv4 allocation; instead,
end hosts will use private IPv4 addresses, possibly allocated by the
CPE. After the allocation, the CPE periodically sends pinhole packet
to the concentrator to install the address mapping and keep it alive.
On data plan, the CPE can be viewed as a regular IPv4 NAT(using
tunnel interface as the NAT outside interface) cascaded with a tunnel
initiator. For IPv4 data packets received from the local network,
the CPE translates these packets, using the tunnel interface address
as the source address, and then encapsulates the translated packet
into IPv6, using the concentrator's IPv6 address as the destination
address, the CPE's IPv6 address as source address. For IPv6 data
packet received from the IPv6 network, the CPE performs decapsulation
and IPv4 public-to-private translation. As to the CPE itself, it
uses the public, tunnel interface address to communicate with the
Cui, et al. Expires January 9, 2012 [Page 10]
Internet-Draft Public 4over6 July 2011
IPv4 Internet, and the private, IPv4 interface address to communicate
with the local network.
5.3. 4over6 concentrator behavior
4over6 concentrator represents the IPv4-IPv6 border router working as
the remote tunnel endpoint for 4over6 initiators, with its IPv6
interface connected to the IPv6 network, IPv4 interface connected to
the IPv4 Internet, and a tunnel interface supporting IPv4-in-IPv6
encapsulation and decapsulation. There's no CGN on the 4over6
concentrator, it won't perform any translation function; instead,
4over6 concentrator maintains an IPv4-IPv6 address mapping table for
IPv4 data encapsulation.
4over6 concentrator maintains the address mapping according to the
initiators' demand. When receiving a pinhole packet from an
initiator, the concentrator reads the IPv4 and IPv6 source addresses
from the packet, install the mapping entry into the mapping table or
renew it if it already exists. When the lifetime of a mapping entry
expires, the concentrator deletes it from the table. So the
initiator should send pinhole packet with an interval shorter than
the lifetime of the mapping entry. The mapping entry is used to
provide correct encapsulation destination address for concentrator
encapsulation. As long as the entry exists in the table, the
concentrator can encapsulate inbound IPv4 packets destined to the
initiator, with the initiator's IPv6 address as IPv6 destination.
On the IPv6 side, 4over6 concentrator decapsulates IPv4-in-IPv6
packets coming from 4over6 initiators. It removes the IPv6 header of
every IPv4-in-IPv6 packet and forwards it to the IPv4 Internet. On
the IPv4 side, the concentrator encapsulates the IPv4 packets
destined to 4over6 initiators. When performing the IPv4-in-IPv6
encapsulation, the concentrator uses its own IPv6 address as the IPv6
source address, uses the IPv4 destination address in the packet to
look up IPv6 destination address in the address mapping table. After
the encapsulation, the concentrator sends the IPv6 packet on its IPv6
interface to reach an initiator.
The 4over6 concentrator, or its upstream router should advertise the
IPv4 prefix which contains the IPv4 addresses of 4over6 users to the
IPv4 side, in order to make these initiators reachable on IPv4
Internet.
Since the concentrator has to maintain the IPv4-IPv6 address mapping
table, the concentrator is stateful in IP level. Note that this
table will be much smaller than a CGN table, as there is no port
information involved.
Cui, et al. Expires January 9, 2012 [Page 11]
Internet-Draft Public 4over6 July 2011
6. Technical advantages
Public 4over6 provides a method for users in IPv6 network to
communicate with IPv4. In many scenarios, this can be viewed as an
alternative to IPv6-IPv4 translation mechanisms which have well-known
limitations described in [RFC4966] .
Since a 4over6 initiator uses a public IPv4 address, Public 4over6
supports full bidirectional communication between IPv4 Internet and
hosts/IPv4 networks in IPv6 access network. In particular, it
supports the servers in IPv6 network to provide IPv4 application
service transparently.
Public 4over6 provides IPv4 access over IPv6 network while keeps
IPv4-IPv6 addressing and routing separated. Therefore the ISP can
manage the native IPv6 network independently without the influence of
IPv4-over-IPv6 requirements, and also provision IPv4 in a flexible,
on-demand way.
Public 4over6 supports dynamic reuse of a single IPv4 address between
multiple subscribers based on their dynamic requirement of
communicating with IPv4 Internet. A subscriber will request a public
IPv4 address for a period of time only when it need to communicate
with IPv4 Internet. Besides, in the CPE case, one public IPv4
address will be shared by the local network. So Public 4over6 can
improve the reuse rate of IPv4 addresses.
Public 4over6 is suited for network users/ISPs which can still get/
provide public IPv4 addresses. Dual-stack lite is suited for network
users/ISPs which can no longer get/provide public IPv4 addresses. By
combining Public 4over6 and Dual-stack lite, the IPv4-over-IPv6 Hub
and spoke problem can be well solved.
Cui, et al. Expires January 9, 2012 [Page 12]
Internet-Draft Public 4over6 July 2011
7. Acknowledgement
The authors would like to thank Alain Durand and Dan Wing for their
valuable comments on this draft.
Cui, et al. Expires January 9, 2012 [Page 13]
Internet-Draft Public 4over6 July 2011
8. References
8.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC4925] Li, X., Dawkins, S., Ward, D., and A. Durand, "Softwire
Problem Statement", RFC 4925, July 2007.
[RFC4966] Aoun, C. and E. Davies, "Reasons to Move the Network
Address Translator - Protocol Translator (NAT-PT) to
Historic Status", RFC 4966, July 2007.
[RFC5549] Le Faucheur, F. and E. Rosen, "Advertising IPv4 Network
Layer Reachability Information with an IPv6 Next Hop",
RFC 5549, May 2009.
[RFC5565] Wu, J., Cui, Y., Metz, C., and E. Rosen, "Softwire Mesh
Framework", RFC 5565, June 2009.
8.2. Informative References
[I-D.cui-softwire-b4-translated-ds-lite]
Cui, Y., Wu, J., and D. Wu, "B4 translated DS-lite enable
AFTR to serve more B4s",
draft-cui-softwire-b4-translated-ds-lite-00 (work in
progress), October 2010.
[I-D.cui-softwire-dhcp-over-tunnel]
Cui, Y., Wu, P., and J. Wu, "DHCPv4 Behavior over IP-IP
tunnel", draft-cui-softwire-dhcp-over-tunnel-00 (work in
progress), June 2011.
[I-D.ietf-pcp-base]
Wing, D., Cheshire, S., Boucadair, M., Penno, R., and P.
Selkirk, "Port Control Protocol (PCP)",
draft-ietf-pcp-base-13 (work in progress), July 2011.
[I-D.ietf-softwire-ds-lite-tunnel-option]
Hankins, D. and T. Mrugalski, "Dynamic Host Configuration
Protocol for IPv6 (DHCPv6) Option for Dual- Stack Lite",
draft-ietf-softwire-ds-lite-tunnel-option-10 (work in
progress), March 2011.
[I-D.ietf-softwire-dual-stack-lite]
Durand, A., Droms, R., Woodyatt, J., and Y. Lee, "Dual-
Stack Lite Broadband Deployments Following IPv4
Cui, et al. Expires January 9, 2012 [Page 14]
Internet-Draft Public 4over6 July 2011
Exhaustion", draft-ietf-softwire-dual-stack-lite-11 (work
in progress), May 2011.
[I-D.sun-v6ops-laft6]
Sun, Q. and C. Xie, "LAFT6: Lightweight address family
transition for IPv6", draft-sun-v6ops-laft6-01 (work in
progress), March 2011.
Cui, et al. Expires January 9, 2012 [Page 15]
Internet-Draft Public 4over6 July 2011
Authors' Addresses
Yong Cui
Tsinghua University
Department of Computer Science, Tsinghua University
Beijing 100084
P.R.China
Phone: +86-10-6260-3059
Email: yong@csnet1.cs.tsinghua.edu.cn
Jianping Wu
Tsinghua University
Department of Computer Science, Tsinghua University
Beijing 100084
P.R.China
Phone: +86-10-6278-5983
Email: jianping@cernet.edu.cn
Peng Wu
Tsinghua University
Department of Computer Science, Tsinghua University
Beijing 100084
P.R.China
Phone: +86-10-6278-5822
Email: weapon@csnet1.cs.tsinghua.edu.cn
Chris Metz
Cisco Systems, Inc.
3700 Cisco Way
San Jose, CA 95134
USA
Email: chmetz@cisco.com
Olivier Vautrin
Juniper Networks
1194 N Mathilda Avenue
Sunnyvale, CA 94089
USA
Email: Olivier@juniper.net
Cui, et al. Expires January 9, 2012 [Page 16]
Internet-Draft Public 4over6 July 2011
Yiu L. Lee
Comcast
One Comcast Center
Philadelphia, PA 19103
USA
Email: yiu_lee@cable.comcast.com
Cui, et al. Expires January 9, 2012 [Page 17]