Networking Working Group A. Brandt
Internet Draft Zensys, Inc.
Intended status: Informational G. Porcu
Expires: November 2008 Telecom Italia
May 13, 2008
Home Automation Routing Requirement in Low Power and Lossy Networks
draft-brandt-roll-home-routing-reqs-01
Status of this Memo
By submitting this Internet-Draft, each author represents that
any applicable patent or other IPR claims of which he or she is
aware have been or will be disclosed, and any of which he or she
becomes aware will be disclosed, in accordance with Section 6 of
BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that other
groups may also distribute working documents as Internet-Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on November 13, 2008.
Copyright Notice
Copyright (C) The IETF Trust (2008).
Abstract
This document presents home control and automation application
specific requirements for ROuting in Low power and Lossy networks
(ROLL). In a modern home, a high number of wireless devices are used
for a wide set of purposes. Examples include lighting control,
heating control, sensors, leak detectors, healthcare systems and
advanced remote controls. Because such devices only cover a limited
Brandt Expires November 13, 2008 [Page 1]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
radio range, multi-hop routing is often required. The aim of this
document is to specify the routing requirements for networks
comprising such constrained devices in a home network environment.
Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [RFC2119].
Table of Contents
1. Terminology....................................................3
2. Introduction...................................................3
3. Home automation applications...................................4
3.1. Turning off the house when leaving........................4
3.2. Energy conservation and optimizing energy consumption.....5
3.3. Moving a remote control around............................5
3.4. Adding a new lamp module to the system....................5
3.5. Controlling battery operated window shades................6
3.6. Remote video surveillance.................................6
3.7. Healthcare................................................6
3.7.1. At-home health reporting.............................7
3.7.2. At-home health monitoring............................7
3.7.3. Healthcare routing considerations....................8
3.8. Alarm systems.............................................8
3.9. Battery-powered devices...................................8
4. Unique requirements of home automation applications............9
4.1. Support of groupcast......................................9
4.2. Metric-based Routing......................................9
4.3. Support of Mobility......................................10
4.4. Support of periodical scanning...........................10
4.5. Scalability..............................................10
4.6. Convergence Time.........................................11
4.7. Manageability............................................11
5. Traffic pattern...............................................11
6. Open issues...................................................11
7. Security Considerations.......................................12
8. IANA Considerations...........................................12
9. Acknowledgments...............................................12
10. References...................................................12
10.1. Normative References....................................12
10.2. Informative References..................................12
Author's Addresses...............................................12
Intellectual Property Statement..................................13
Disclaimer of Validity...........................................13
Brandt Expires November 13, 2008 [Page 2]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
1. Terminology
ROLL: ROuting in Low-power and Lossy networks
Access Point: The access point is an infrastructure device that
connects the low power and lossy network system to the
Internet, possibly via a customer premises local area
network (LAN).
LAN: Local Area Network.
PAN: Personal Area Network.
A geographically limited wireless network based on
e.g. 802.15.4 or Z-Wave radio.
Channel: RF frequency band used to transmit a modulated signal
carrying packets.
Downstream: Data direction traveling from a LAN to a PAN device.
Upstream: Data direction traveling from a PAN to a LAN device.
RF: Radio Frequency.
Sensor: A PAN device that measures data and/or detects an
event.
HA: Home Automation.
2. Introduction
This document presents the home control and automation application
specific requirements for Routing in Low power and Lossy Networks
(ROLL). In a modern home, a high number of wireless devices are used
for a wide set of purposes. Examples include lighting control
modules, heating control panels, light sensors, temperature sensors,
gas/water leak detectors, motion detectors, video surveillance,
healthcare systems and advanced remote controls. Basic home control
modules such as wall switches and plug-in modules may be turned into
an advanced home automation solution via the use of an IP-enabled
application responding to events generated by wall switches, motion
sensors, light sensors, rain sensors, and so on.
Brandt Expires November 13, 2008 [Page 3]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
Because such devices only cover a limited radio range, multi-hop
routing is often required. These devices are usually highly
constrained in term of resources such as battery and memory and
operate in unstable environments. Persons moving around in a house,
opening or closing a door or starting a microwave oven affect the
reception of weak radio signals. Reflection and absorption may cause
a reliable radio link to turn unreliable for a period of time and
then being reusable again, thus the term "lossy".
Unlike other categories of PANs, the connected home area is very much
consumer-oriented. The implications on network nodes in this aspect,
is that devices are very cost sensitive, which leads to resource-
constrained environments having slow CPUs and small memory
footprints. At the same time, nodes have to be physically small which
puts a limit to the physical size of the battery; and thus, the
battery capacity. As a result, it is common for low-power sensor-
style nodes to shut down radio and CPU resources for most of the
time. Often, the radio uses the same power for listening as for
transmitting.
Section 3. describes a few typical use cases for home automation
applications. Section 4. discusses the routing requirements for
networks comprising such constrained devices in a home network
environment. These requirements may be overlapping requirements
derived from other application-specific requirements documents or as
listed in [I-D.culler-roll-routing-reqs].
3. Home automation applications
Home automation applications represent a special segment of networked
wireless devices with its unique set of requirements. To facilitate
the requirements discussion in Section 4, this section lists a few
typical use cases of home automation applications. New applications
are being developed at a high pace and this section does not mean to
be exhaustive. Most home automation applications tend to be running
some kind of command/response protocol. The command may come from
several places. For instance a lamp may be turned on, not only be a
wall switch but also from a movement sensor.
3.1. Turning off the house when leaving
Using the direct analogy to an electronic car key, a house owner may
activate the "leaving home" function from an electronic house key,
mobile phone, etc. For the sake of visual impression, all lights
should turn off at the same time. At least, it should appear to
happen at the same time. A well-known problem in wireless home
automation is the "popcorn effect": Lamps are turned on one at a
Brandt Expires November 13, 2008 [Page 4]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
time, at a rate so slow that it is clearly visible. Some existing
home automation solutions use a clever mix of a "subnet groupcast"
message with no acknowledgement and no forwarding before sending
acknowledged singlecast messages to each lighting device.
The controller forms the groups and decides which nodes should
receive "turn-off" or "turn-on" requests.
Thus, a solution is needed for addressing groups of nodes without
prior management of group membership in the receiving nodes.
3.2. Energy conservation and optimizing energy consumption
Parts of the world using air conditioning may let shades go down and
turn off the AC device when leaving home. Air conditioning may start
by timer or via motion sensor when the owner returns home. The owner
may even activate the air conditioning via cell phone before getting
home.
Geographical areas using central heating may turn off heating when
not at home and use a reduced temperature during night time.
The power grid may experience periods where more wind-generated power
is produced than is needed. Typically this may happen during night
hours. The washing machine and dish washer may just as well work
while power is cheap. The electric car should also charge its
batteries on cheap power.
Most of these applications are mains powered and may thus provide
reliable routing resources.
3.3. Moving a remote control around
A remote control is a typical example of a mobile device in a home
automation network. An advanced remote control may be used for
dimming the light in the dining room while eating and later on,
turning up the music while doing the dishes in the kitchen. Reaction
must appear to be instant (within a few hundred milliseconds) even
when the remote control has moved to a new location. The remote
control may be communicating to either a central home automation
controller or directly to the lamps and the media center.
3.4. Adding a new lamp module to the system
Small-size, low-cost modules may have no user interface except for a
single button. Thus, an automated inclusion process is needed for
controllers to find new modules. Inclusion covers the detection of
Brandt Expires November 13, 2008 [Page 5]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
neighbors and assignment of a unique node ID. Inclusion should be
completed within a few seconds.
3.5. Controlling battery operated window shades
In consumer premises, window shades are often battery-powered as
there is no access to mains power over the windows. For battery
conservation purposes, the receiver is sleeping most of the time. A
home automation controller sending commands to window shades via ROLL
resources will have no problems delivering the packet to the router,
but the router will have to wait for some time before the command can
be delivered to the window shades; e.g. up to 250ms.
3.6. Remote video surveillance
Remote video surveillance is a fairly classic application for Home
networking providing the ability for the end user to get a video
stream from a Web Cam reached via the Internet, which can be
triggered by the end-user that has received an alarm from a movement
sensor or smoke detector - or the user simply wants to check the home
status via video.
Note that in the former case, more than likely, there will be a form
of inter-device communication: indeed, upon detecting some movement
in the home, the movement sensor may send a request to the light
controller to turn-on the lights, to the Web Cam to start a video
stream that would then be directed to the end user (cell phone, PDA)
via the Internet.
By contrast with other applications, e.g. industrial sensors where
data would mainly be originated by sensor to a sink and vice versa,
this scenario implicates a direct inter-device communication between
ROLL devices.
3.7. Healthcare
By adding communication capability to devices, patients and elderly
citizens may be able to do simple measurements at home. Thanks to
online devices, a doctor can keep an eye on the patient's health and
receive warnings if a new trend is discovered by automated filters.
Fine-grained daily measurements presented in proper ways may allow
the doctor to establish a more precise diagnosis.
Such applications may be realized as wearable products which
frequently do a measurement and automatically deliver the result to a
data sink locally or over the Internet.
Brandt Expires November 13, 2008 [Page 6]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
Applications falling in this category are referred to as at-home
health reporting. Whether measurements are done in a fixed interval
or if they are manually activated, they leave all processing to the
receiving data sink.
A more active category of applications may send an alarm if some
alarm condition is triggered. This category of applications is
referred to as at-home health monitoring. Measurements are
interpreted in the device and may cause reporting of an event if an
alarm is triggered.
Many implementations may overlap both categories.
3.7.1. At-home health reporting
Applications might include:
o Temperature
o Weight
o Blood pressure
o Insulin level
Measurements may be stored for long term statistics. At the same
time, a critically high blood pressure may cause the generation of an
alarm report. Refer to 3.7.2.
To avoid a high number of request messages, nodes may be configured
to autonomously do a measurement and send a report in intervals.
3.7.2. At-home health monitoring
An alarm event may become active e.g. if the measured blood pressure
exceeds a threshold or if a person falls to the ground.
Applications might include:
o Temperature
o Weight
o Blood pressure
o Insulin level
Brandt Expires November 13, 2008 [Page 7]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
o ECG
o Position tracker
3.7.3. Healthcare routing considerations
From a ROLL perspective, all the above-mentioned applications may run
on battery. They may also be portable and therefore need to locate a
new neighbor router on a frequent basis.
Not being powered most of the time, the nodes should not be used as
routing nodes. However, sleeping, battery-powered nodes may be
involved in routing. Examples include cases where a person falls
during a power blackout. In that case it may be that no mains-powered
routers are available for forwarding the alarm message to a (battery-
backed) internet gateway located out of direct range.
Delivery of measurement data has a more relaxed requirement for route
discovery time compared to a remote control. On the other hand, it is
critical that a "person fell" alarm is actually delivered in the end.
3.8. Alarm systems
A home security alarm system is comprised of various devices like
vibration detectors, fire or carbon monoxide detection system, door
or window contacts, glass-break detector, presence sensor, panic
button, home security key.
Some smoke alarms are battery powered and at the same time mounted in
a high place. Battery-powered safety devices should only be used for
routing if no other alternatives exist. A smoke alarm with a drained
battery does not provide a lot of safety. Also, it may be
inconvenient to exchange battery in a smoke alarm. Finally, routing
via battery-powered nodes may be very slow if they are sleeping most
of the time.
All of the above-mentioned reasons suggest that routing should be
avoided via this category of devices.
A plethora of applications could be developed for home alarm system:
most of them, most of the time, have prevention and monitoring
activity in which routing requirements are deterministic, but all of
them have an alarm state in which nodes may burst an aperiodic alarm.
3.9. Battery-powered devices
For convenience and low operational costs, power consumption of
consumer products must be kept at a very low level to achieve a long
battery lifetime. One implication of this fact is that RAM memory is
Brandt Expires November 13, 2008 [Page 8]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
limited and it may even be powered down; leaving only a few 100 bytes
alive during the sleep phase.
4. Unique requirements of home automation applications
Home automation applications have a number of specific requirements
related to the set of home networking applications and the perceived
operation of the system.
4.1. Support of groupcast
The routing protocol must provide the ability to route a packet
towards a single device (unicast), a set of devices (also referred to
as "groupcast" in this document) or all devices (broadcast) in the
house.
The support of unicast, groupcast and broadcast also has an
implication on the addressing scheme and are outside the scope of
this document that focuses on the routing requirements aspects.
It MUST be to possible to address a group of receivers known by the
sender even if the receivers do not know that they have been grouped
by the sender.
Alternatively, a companion specification SHOULD define how to
indirectly address a group of nodes on the application layer via
classic broadcast in the network layer; e.g. by use of a bitmap in a
header extension.
4.2. Metric-based Routing
[ABR NOTE: IETF-71 WG meeting indicated that the term "constrained"
has a very specific meaning in the routing community inside IETF.
What I understood was that the draft should be using the term
"metric-based routing"]
Simple battery-powered nodes such as movement sensors on garage doors
and rain meters may not be able to assist in routing. Depending on
the node type, the node never listens at all, listens rarely or makes
contact on demand to a pre-configured target node. Attempting to
communicate to such nodes may require long time before getting a
response.
Other battery-powered nodes may have the capability to participate in
routing. The routing protocol should either share the load between
nodes to preserve battery or only route via mains-powered nodes if
Brandt Expires November 13, 2008 [Page 9]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
possible. The most reliable routing resource may be a battery-backed,
mains-powered smoke alarm.
The routing protocol MUST support metric-based routing taking into
account node properties (CPU, memory, level of energy, sleep
intervals, safety/convenience of changing battery).
4.3. Support of Mobility
In a home environment, although the majority of devices are fixed
devices, there is still a variety of mobile devices: for example a
multi-purpose remote control is likely to move. Another example of
mobile devices is wearable healthcare devices.
While healthcare devices delivering measurement results can tolerate
route discovery times measured in seconds, a remote control appears
unresponsive if using more than 0.5 seconds to e.g. pause the music.
While, in theory, all battery-powered devices and mains-powered plug-
in modules may be moved, the predominant case is that the sending
node has moved while the rest of the network has not changed.
The routing protocol MUST provide mobility with convergence time
below 0.5 second if only the sender has moved.
The routing protocol SHOULD make use of the fact that if not being
able to deliver a packet, it is most likely that the sending node
moved; rather than the rest of the network.
4.4. Support of periodical scanning
The routing protocol MUST support the recognition of neighbors and
periodical scanning. This process SHOULD preserve energy capacity as
much as possible.
(Derived from use case 3.8. Alarm Systems)
4.5. Scalability
Looking at the number of wall switches, power outlets, sensors of
various nature, video equipment and so on in a modern house, it seems
quite realistic that hundreds of low power devices may form a home
automation network in a fully populated "smart" home. Moving towards
professional building automation, the number of such devices may be
in the order of several thousands.
Brandt Expires November 13, 2008 [Page 10]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
Thus, the routing protocol MUST support 250 devices in a subnet.
The routing protocol SHOULD support 2500 devices in a subnet.
4.6. Convergence Time
A home automation PAN is subject to various instability due to signal
strength variation, moving persons and the like. Furthermore, as the
number of devices increases, the probability of a node failure also
increases.
Measured from the transmission of a packet, the following convergence
time requirements apply.
The routing protocol MUST converge within 0.5 second if no nodes have
moved.
The routing protocol MUST converge within 2 seconds if the
destination node of the packet has moved.
4.7. Manageability
The ability of the home network to support auto-configuration is of
the utmost importance. Indeed, most end users will not have the
expertise and the skills to perform advanced configuration and
troubleshooting. Thus the routing protocol designed for home PAN MUST
provide a set of features including 0 configuration of the routing
protocol for a new node to be added to the network.
Furthermore, a failing node MUST NOT have a global impact on the
routing protocol. The routing protocol SHOULD support the ability to
isolate a misbehaving node thus preserving the correct operation of
overall network.
5. Traffic pattern
Depending on the philosophy of the home network, wall switches may be
configured to directly control individual lamps or alternatively, all
wall switches send control commands to a central lighting control
computer which again sends out control commands to relevant devices.
In a distributed system, the traffic tends to be any-to-many. In a
centralized system, it is a mix of any-to-one and one-to-many.
6. Open issues
Other items to be addressed in further revisions of this document
include:
Brandt Expires November 13, 2008 [Page 11]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
o Load Balancing (Symmetrical and Asymmetrical)
o Security
7. Security Considerations
TBD
8. IANA Considerations
This document includes no request to IANA.
9. Acknowledgments
This document was prepared using 2-Word-v2.0.template.dot.
10. References
10.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
10.2. Informative References
[I-D.culler-roll-routing-reqs]
Vasseur, J. and D. Culler, "Routing Requirements for Low
Power And Lossy Networks",
draft-culler-roll-routing-reqs-* (work in progress).
Author's Addresses
Anders Brandt
Zensys, Inc.
Emdrupvej 26
Copenhagen, DK-2100
Denmark
Email: abr@zen-sys.com
Brandt Expires November 13, 2008 [Page 12]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
Giorgio Porcu
Telecom Italia
Piazza degli Affari, 2
20123 Milan
Italy
Email: giorgio.porcu@telecomitalia.it
Intellectual Property Statement
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Disclaimer of Validity
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Copyright Statement
Copyright (C) The IETF Trust (2008).
Brandt Expires November 13, 2008 [Page 13]
Internet-Draft draft-brandt-roll-home-routing-reqs May 2008
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
Acknowledgment
Funding for the RFC Editor function is currently provided by the
Internet Society.
Brandt Expires November 13, 2008 [Page 14]