Applicability of Stateful Path Computation Element (PCE)
draft-zhang-pce-stateful-pce-app-01
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Replaced".
|
|
|---|---|---|---|
| Authors | Fatai Zhang , Xian Zhang , Young Lee , Ramon Casellas , Oscar Gonzalez de Dios | ||
| Last updated | 2012-07-13 | ||
| Replaced by | draft-ietf-pce-stateful-pce-app, draft-ietf-pce-stateful-pce-app, draft-ietf-pce-stateful-pce-app, RFC 8051 | ||
| RFC stream | (None) | ||
| Formats | |||
| Additional resources | |||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-zhang-pce-stateful-pce-app-01
Network Working Group Fatai Zhang
Internet-Draft Xian Zhang
Intended status: Informational Young Lee
Huawei
Ramon Casellas
CTTC
Oscar Gonzalez de Dios
Telefonica I+D
Expires: January 13, 2013 July 13, 2012
Applicability of Stateful Path Computation Element (PCE)
draft-zhang-pce-stateful-pce-app-01.txt
Status of this Memo
This Internet-Draft is submitted to IETF in full conformance with
the provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other
documents at any time. It is inappropriate to use Internet-Drafts
as reference material or to cite them other than as "work in
progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on Janunary 13, 2013.
Abstract
Zhang Expires January 2013 [Page 1]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
The Path Computation Element (PCE) provides a solution for Traffic
Engineering (TE) based path calculation in large, multi-domain,
multi-region, or multi-layer networks. Depending on whether a PCE
keeps information about LSPs and reserved resource usage in the
network or not, it can be categorized as either stateful or
stateless.
This memo describes general considerations for stateful PCE(s) and
examines its applicability through a number of typical scenarios. It
shows how stateful PCE(s) can be applied to facilitate these
applications. PCEP extensions required for stateful PCE usage are
covered in separate document(s).
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [RFC2119].
Table of Contents
Table of Contents .............................................. 2
1. Introduction ................................................ 3
2. General Considerations....................................... 4
2.1. Architectural Considerations............................ 4
2.2. LSP State Synchronization............................... 5
2.2.1. Single Domain...................................... 5
2.2.2. Multi-domain....................................... 6
2.2.3. Multi-layer........................................ 8
2.3. PCE Survivability/Reliability........................... 8
2.4. Delegation and Policy................................... 8
2.4.1. Use of Under-construction LSPs Information..........8
3. Application Scenarios....................................... 10
3.1. Impairment-Aware Routing and Wavelength Assignment (IA-RWA)
........................................................... 10
3.2. Defragmentation in Flexible Grid Networks ..............11
3.3. Recovery .............................................. 12
3.3.1. Protection........................................ 12
3.3.2. Restoration....................................... 13
3.4. SRLG Diversity ........................................ 14
3.5. Maintenance of Virtual Network Topology (VNT) ..........15
3.6. Global Concurrent Optimization (GCO) ...................15
3.7. Point-to-Multipoint (P2MP) Application .................16
3.8. Time-based Scheduling ..................................16
4. Manageability Considerations ................................17
Zhang Expires January 2013 [Page 2]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
4.1. Information and Data Models ............................17
5. Security Considerations .....................................17
6. References .................................................17
6.1. Normative References ...................................17
6.2. Informative References .................................18
7. Contributors' Address .......................................20
Authors' Addresses ............................................ 20
1. Introduction
[RFC 4655] defines the architecture for a Path Computation Element
(PCE)-based model for the computation of Multiprotocol Label
Switching (MPLS) and Generalized MPLS (GMPLS) Traffic Engineering
Label Switched Paths (TE LSPs). To perform such a constrained
computation, a PCE stores the network topology (i.e., TE links and
nodes) and resource information (i.e., TE attributes) in its TE
Database (TED). To request path computation services to a PCE, [RFC
5440] defines the PCE Communication Protocol (PCEP) for
communications between a Path Computation Client (PCC) and a PCE, or
between two PCEs. A PCC can initiate a path computation request to a
PCE through a Path Computation Request (PCReq) message, and then the
PCE will return the computed path to the requesting PCC in response
to a previously received PCReq message through a PCEP Path
Computation Reply (PCRep) message.
As per [RFC 4655], a PCE can be either stateful or stateless.
Compared to a stateless PCE, a stateful PCE stores not only the
network states, but also the set of computed paths and reserved
resources in use in the network. In other words, the ''state'' in a
stateful PCE is determined not only by the TED but also by the set
of active LSPs and their corresponding reserved resources.
Furthermore, a stateful PCE might also retain the information of
LSPs under construction in order to reduce resource contention. Such
augmented state allows the PCE to compute constrained paths while
considering individual LSPs and their interaction. Note that
[RFC4655] further specifies that the TED contains link state and
bandwidth availability as distributed by the IGPs or collected via
other methods. Even if such information can provide increased
granularity and more detail, it is not state information in the PCE
context and so a model that uses it is still described as a
stateless PCE.
As described in section 6.8 of [RFC 4655], there are many
applications which can benefit from stateful PCE(s), e.g.:
Zhang Expires January 2013 [Page 3]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
o Minimum perturbation: stateful PCE(s) can minimize the number of
existing TE LSPs that are affected and preempted by a higher-
priority TE LSP request in a crowded network.
o Virtual Network Topology (VNT) maintenance: the information of
existing LSPs in the higher layer is used as an input for setting
up/tearing down the LSPs in the lower layer (i.e., VNT modification).
Besides these scenarios, there are some additional scenarios that
should be investigated further. For instance, in impairment-aware
Wavelength Switched Optical Networks (WSON) [WSON-Impairment],
stateful PCEs could be used to perform Impairment-Aware Routing and
Wavelength Assignment (IA-RWA) procedures. In this case, PCE(s) need
to know the detailed information of the existing LSPs so that the
new LSP(s) will not impact them. Such PCE(s) would maintain the
existing LSPs states (e.g., route, wavelength and speed) to perform
impairment aware RWA procedures simpler and with less protocol
overhead.
[RFC 4655] also discusses potential scalability and synchronization
issues in order to implement stateful PCE(s). The main problem
pointed out by [RFC 4655] is that a PCE would be constrained if the
states of all the TE LSPs in a network are to be maintained by a PCE.
Moreover, such state, when there are multiple PCEs, needs to be
properly synchronized. These issues are especially relevant in
packet networks, such as MPLS-TE networks, given a potentially large
number of LSPs. Nonetheless, it is expected that in transport
networks, such as OTN networks, the number of the LSPs will be much
smaller, which makes stateful PCEs more applicable. Finally, with
the increasing power and memory of the hardware platforms that a PCE
may run, the number of LSPs that can be managed by a PCE is
significantly large. Hence, there is lesser scaling issue for a PCE
to store all the LSPs' states, especially for a transport network.
This document presents general considerations for stateful PCE(s)
and several examples of its application scenarios. It exhibits the
utility of stateful PCE(s) in effective support of these
applications to obtain better performance. PCEP extension details
are covered in separate documents [stateful-PCEP-mpls], [stateful-
PCE-gmpls].
2. General Considerations
2.1. Architectural Considerations
Several PCE architectures are described in Section 5 of [RFC4655]. A
stateful PCE needs to maintain a large amount of data and
potentially incur in a very high amount of control plane overhead.
Zhang Expires January 2013 [Page 4]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
Moreover, there might be high computational demands on stateful PCE
entities to effectively support the applications listed in Section 3.
Therefore, the composite PCE architecture is NOT RECOMMENDED to
support stateful PCEs. It does not exclude the possibility that
multiple PCEs with different capabilities are included in the
network. For example, both stateless and stateful PCEs can co-exist
to be in charge of path computation of different types. In all cases,
the stateful capability of PCE should be made known within the
domain.
2.2. LSP State Synchronization
As suggested by the definition, a stateful PCE maintains two
databases for path computation. The first one is the Traffic
Engineering Database (TED) which includes the topology and resource
in the network. TED can be obtained through participating in routing
distribution of TE information or other means as explained in
Section 6.7 of [RFC4655].
The other database is the LSP state Database (LSP-DB), in which a
PCE stores attributes of all existing LSPs in the network, such as
payload signal, switching types and bandwidth/resource usage etc. A
stateful PCE should gather the LSP information either from the
network management system (NMS) or from the nodes in the network.
For a NMS-based PCE, if the PCE is not co-llocated with the NMS, a
standard communication protocol might is be needed for LSP state
synchronization; otherwise, proprietary APIs can be used. If a PCE
reliesy on network nodes for state synchronization, the strategies
may vary depending on the network scenarios in which the PCE is
applied to (i.e., single domain, multiple domain or multi-layer
networks.) as well as the adoption of PCE computation model.
2.2.1. Single Domain
In a single domain network, LSP state information is maintained
locally by the nodes initiating LSP(s). Therefore, PCE(s) should
gather the LSP state information either passively or actively from
the nodes in the network they have visibility. With a centralized
stateful PCE computation model, it is straightforward that all nodes
in the domain could communicate with the PCE for its LSP-DB
synchronization. As for distributed stateful PCE computation model
(i.e., there are multiple stateful PCEs in the network), there are
several alternatives for synchronization:
o Every node can update the PCE LSP-DBs by sending the LSP state
information to each of the PCEs in the network separately.
Zhang Expires January 2013 [Page 5]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
o Another feasible strategy is to choose one of the PCEs (i.e., a
designated PCE) for synchronization with all the nodes in the
network and the designated PCE also updates the LSP-DBs of all the
other PCE(s).
o A mixed of these two methods listed above can also be considered in
which more than one PCEs (e.g., two PCEs) are chosen to interact
directly with nodes in the network for state synchronization while
other PCEs are updated via these PCEs.
2.2.2. Multi-domain
In a multi-domain network with a centralized PCE model, the LSP
state synchronization is similar to that of a single domain scenario.
If there is a stateful PCE responsible for performing path
computation within each domain, the LSPs (segments) traversing the
domain/layer should be synchronized to the PCE.
As described in [RFC4726], there are four methods to set up a LSP
traversing multiple domains: LSP nesting, contiguous LSP, LSP
stitching and hybrid methods, respectively. Hence, the ingress nodes
of a LSP traversing a domain may exist in another domain (e.g., a
contiguous LSP spanning across multiple domains). In this case, the
border node of a domain (i.e., an intermediate node of a LSP), could
be responsible for synchronizing the LSP segment in the domain to
the PCE.
+---------------------+---------------------+
| +----+ | +----+ |
| |PCE1| | |PCE2| |
| +----+ | +----+ |
| Domain 1 | Domain 2 |
| +--+ +--+ +--+ | +--+ +--+ +--+ |
| |N1+---+N2+---+N3+---+N7+---+N8+---+N9| |
| +-++ +--+ +-++ | +-++ +--+ +-++ |
| | | | | | |
| | | | | | |
| +-++ +--+ +-++ | +-+-+ +--++ |
| |N4+---+N5+---+N6+---+N10+--------+N11| |
| +--+ +--+ +--+ | +---+ +---+ |
+---------------------+---------------------+
Figure 1: Multi-domain Scenario
Figure 1 shows an example of multi-domain scenario. Suppose a
contiguous LSP traverses N1-N2-N3-N7-N8-N9. Then in domain 1, the
ingress node of the LSP (i.e., N1) SHOULD synchronize the state of
Zhang Expires January 2013 [Page 6]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
the LSP segment N1-N2-N3 to PCE1. In domain 2, the border node (i.e.,
N7) SHOULD synchronize the state of the LSP segment N7-N8-N9 to PCE2.
This approach requires that N7 has a PCEP adjacency with its PCE
(PCE2), i.e. setting up a PCEP session, for LSP state
synchronization purpose even if no path computation expansions are
required. N7 needs to check whether its RSVP-TE upstream node
belongs to another domain and notify the PCE when the LSP is
released. Note that synchronization may require detailed information
of the LSP (e.g., a full record route, the actual reserved resources)
which may only be available during Resv message processing.
Alternatively, inter-PCE communication strategy can be adopted for
LSP-DB synchronization. For instance, in Figure 1, upon the
notification of the setup of LSP N1-N2-N3-N7-N8-N9, PCE1 can
establish a PCEP adjacency to inform PCE2 to update its LSP-DB. This
method SHOULD be preferred only when PCE1 has sufficient and valid
information of the across-domain LSP, such as explicit LSP
information. Otherwise, the method in which the border node(s) are
in charge of LSP state update is more appropriate. For example,
Backward Recursive Path Computation (BRPC) [RFC5441] in conjunction
with path-key-based mechanism [RFC5520] can be adopted for inter-
domain path computation. If this is the case with the example in
Figure 1, PCE1 only acquires a loose LSP path (e.g., N1-N2-N3-N7-
KEY1, where KEY1 can be interpreted only by PCE2). Since it depends
on the local policy that how long a Path-Key should be stored, KEY1
might not be valid anymore when it is used by PCE1 for PCE2 LSP-DB
update notification. In this case, N7 will need to request PCE2 to
unlock the Path-Key in order to complete the signaling process.
Therefore, it is possible to use N7 instead for updating PCE2 LSP-DB.
Note that a timely synchronization of PCEs and these two databases
is a prerequisite to maintaining a good performance of a stateful
PCE.
To benefit from stateful PCE, during inter-domain path computation
procedure, PCC and cooperating PCEs should try to select stateful
PCE when multiple PCEs (stateful and stateless) are available in the
domain. This will enable correct end-to-end path computation using
of TED and LDP-DB in all domains. In case of unavailability of
stateful PCE, stateless PCE can still be used to provide the inter-
domain path computation.
The inter-domain LSP synchronization as explained in this section is
still applicable if some domain does not have stateful PCE support.
All the domains with a stateful PCE present should synchronize their
segment at the least.
Zhang Expires January 2013 [Page 7]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
2.2.3. Multi-layer
In multi-layer scenarios, one node/domain may have multiple
switching capabilities. For instance, Optical Transport Network (OTN)
nodes may have both of electrical (e.g., ODU1, ODU2, ODU3) and
optical switch capabilities. ODU LSPs and wavelength LSPs may be
established in an OTN network.
In such networks, a PCE may have the capability of performing single
layer path computation or multi-layer path computation. If a
stateful PCE has single layer path computation capability, the nodes
should be aware of information pertaining to which layer should be
synchronized to a specific PCE. Otherwise, the state of the LSPs in
all layers should be synchronized to the single stateful PCE.
2.3. PCE Survivability/Reliability
Since a PCE supports a centralized path computation model, its
survivability should be carefully considered to ensure its proper
operation. If a multiple stateful PCE model is used and these PCEs
have a consistent view of the network, they can act as a hot backup
for each other. Otherwise, other backup strategies SHOULD be present
if only one PCE is deployed in the network to avoid a single point
of failure.
2.4. Delegation and Policy
Stateful PCE(s) are still subject to policies when performing path
computation based on TED and LSP-DB as well as in what concerns LSP-
DB organization and maintenance.
For LSP-DB maintenance, a basic function of stateful PCEs that
SHOULD be supported is the ability to keep LSP state information in
the network within which they have visibility. OPTIONALLY, a
stateful PCE can also extend its ability to support modification of
LSP state information. This can be realized by obtaining the
temporal LSP state control through negotiation with LSRs (i.e., LSP
delegation). Please note that LSP state delegation should comply
with the policy imposed by LSP state owner (i.e., LSRs) as well as
the policy imposed upon PCE(s).
2.4.1. Use of Under-construction LSPs Information
The TED and/or LSP-DB information retained by a stateful PCE might
be out-of-syn. If this is the case, it might cause resource
contention when the PCE computes paths based of the out-of-date
information. Some sources of the potential TED/LSP-DB inaccuracy are:
Zhang Expires January 2013 [Page 8]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
o Control plane link latencies. Such latencies may be increased
due to several factors such as:
a) The time required for a PCC to obtain the paths after a
successful computation, requiring several Round-Trip-Times
(RTT) as per TCP;
b) The setup delay;
c) The time it takes for the PCE to update the local TED given
IGP update times;
o The routing and topology dissemination protocol (i.e. OSPF-TE),
which may operate with timers for LSA updates, to avoid excessive
control plane overhead.
o Concurrent requests that arrive during the time window, between
a response is sent and the LSP is setup and the topology changes are
flooded. Even for very fast networks with low latency, there may be
a batched of requests: several path computation requests within a
PCReq message or, in dynamic restoration without pre-planning,
several LSPs that need to be rerouted so as to avoid a failed link.
o Local PCE contention, where the PCE needs to concurrently serve
path computation requests and update the LSA (e.g. parsing OSPF-TE
LSA updates). A PCE implementation may need to find a trade-off,
when synchronizing access to the local TED: favor OSPF-TE parsing
which means that some path computations are slightly delayed to
allow an 'update' to be processed, or give strict priority to
computation requests.
In consequence, a PCE may assign the same (or a subset of the
same) resources to several requests. Thus, it may result in
contention and degraded network performance since it might cause
path setup failure and excessive crank-backs.
Therefore, information of the LSPs that are under construction
can be used together with the TED and LSP-DB by a stateful PCE to
reduce the path blocking and crank-backs issues. For example, the
PCE can retain some context from paths it has recently computed so
that it avoids suggesting the use of the same resources for other TE
LSPs, using heuristics / statistic or forecasting for improved
resource (i.e. wavelength) allocation. In other words, a given PCE
implementation may decide to perform additional book-keeping and
management of resources strategies using the information of under
construction LSPs, deploying policies that prevent sub-optimal
allocations. For instance, a PCE may compute the mean time used to
update the TED based on the previous calculated TE-LSPs and TED
Zhang Expires January 2013 [Page 9]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
updates. Those kinds of mechanisms may reduce the TED inaccuracy
but in all cases they cannot infer the PCC use of the TE-path.
3. Application Scenarios
In this section, several examples exploiting the capabilities of
stateful PCE(s) are presented, although the application of stateful
PCE(s) is not limited to them. In general, stateful PCE(s) can be
deployed for applications where LSP state as well as traffic
engineering information in the network are necessary inputs to
achieve one or multiple of the following goals:
o Improving the performance such as reducing network blocking
probability, achieving load balancing, improve network resources
utilization or increasing the route computation success rate;
o Reducing the complexity of the relevant procedure(s) associated
with the application(s);
o Lowering resource consumption;
As discussed in [PSU-WSON] and [LCA-Stateless], some of the
objectives can be achieved through limited LSP awareness in
stateless PCE by exploiting objects defined in existing protocols,
such as the SVEC object defined in [RFC5440] and/or XRO object
defined in [RFC5521]. These methods are considered as transitional
solutions because of two reasons. Firstly, these methods only have
local/partial/temporal LSP related information and thus have limited
utility in terms of achieving the goals, particularly for objectives
set at a network level. Secondly, it might incur a substantial
amount of overhead since it requires frequent message exchanges
among PCC and PCE entities.
3.1. Impairment-Aware Routing and Wavelength Assignment (IA-RWA)
In WSON networks [RFC6163], a wavelength-switched LSP traverses one
or multiple fiber links. The bit rates of the client signals carried
by the wavelength LSPs may be the same or different. Hence, a fiber
link may transmit a number of wavelength LSPs with equal or mixed
bit rate signals. For example, a fiber link may multiplex the
wavelengths with only 10G signals, mixed 10G and 40G signals, or
mixed 40G and 100G signals.
IA-RWA in WSONs refers to the RWA process (i.e., lightpath
computation) that takes into account the optical layer/transmission
imperfections by considering as additional (i.e., physical layer)
constraints. To be more specific, linear and non-linear effects
associated with the optical network elements should be incorporated
Zhang Expires January 2013 [Page 10]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
into the route and wavelength assignment procedure. For example, the
physical imperfection can result in the interference of two adjacent
lightpaths. Thus, a guard band should be reserved between them to
alleviate these effects. The width of the guard band between two
adjacent wavelengths depends on their characteristics, such as
modulation formats and bit rates. Two adjacent wavelengths with
different characteristics (e.g., different bit rates) may need a
wider guard band and with same characteristics may need a narrower
guard band. For example, 50GHz spacing may be acceptable for two
adjacent wavelengths with 40G signals. But for two adjacent
wavelengths with different bit rates (e.g., 10G and 40G), a larger
spacing such as 300GHz spacing may be needed. Hence, the
characteristics (states) of the existing wavelength LSPs SHOULD be
considered for a new RWA request in WSON.
In summary, when stateful PCE(s) are used to perform the IA-RWA
procedure, it needs to know the characteristics of the existing
wavelength LSPs. The impairment information relating to existing and
to-be-established LSPs can be obtained by nodes in WSON networks via
external configuration or other means such as monitoring or
estimation based on a vendor-specific impair model. However, WSON
related routing protocols, i.e., [GEN-OSPF] and [WSON-OSPF], only
advertise limited information (i.e., availability) of the existing
wavelengths, without defining the supported client bit rates. It
will incur substantial amount of control plane overhead if routing
protocols are extended to support dissemination of the new
information relevant for the IA-RWA process. In this scenario,
stateful PCE(s) would be a more appropriate mechanism to solve this
problem. Stateful PCE(s) can exploit impairment information of LSPs
stored in LSP-DB to provide accurate RWA calculation.
3.2. Defragmentation in Flexible Grid Networks
Traditionally, in Dense Wavelength Division Multiplexing (DWDM)
networks, the frequency and channel spacing for a single wavelength
allocated to an optical connection is fixed, in terms of a fixed
channel spacing grid. With the development of mixed-rate
transmission and the increase in the speed of optical signal, the
issue of poor optical spectrum usage needs to be addressed. Flexible
grid is proposed to solve this problem [G.FLEXIGRID]. In Flexible
grid networks, LSPs with different slot widths (such as 12.5G, 25G
etc.) can co-exist so as to accommodate the services with different
bandwidth requests.
Yet another problem arises in this type of DWDM networks. Since in
flexible grid networks LSPs are dynamically allocated and released
over time, the optical spectrum resource becomes fragmented. The
overall available spectrum resource on a link might be sufficient
Zhang Expires January 2013 [Page 11]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
for a new LSP request. But if the available spectra are not
continuous, the request would be rejected. In order to perform
frequency defragmentation procedure, stateful PCE(s) COULD be used,
since existing TE LSPs information (i.e., slot width and spectrum
location information associated with TE LSPs) is required to
accurately assess spectrum resources on the LSPs, and perform de-
fragmentation while ensuring a minimal disruption of the network,
e.g., based on active LSP priorities.
[Editor's note: it is not suggested to start PCEP extensions on this
application until the data plane technology and the corresponding
GMPLS control is mature.]
3.3. Recovery
3.3.1. Protection
For protection purposes, a PCC may send a request to a PCE for
computing a set of paths for a given LSP. Alternatively, the PCC can
send multiple requests to the PCE, asking for working and backup
LSPs separately. In either way, the resources bound to backup paths
can be shared by different LSPs to improve the overall network
efficiency. If resource sharing is supported for LSP protection, the
information relating to existing LSPs is required to avoid
allocation of shared protection resources to two LSPs that might
fail together and cause protection contention issues. If such
information is required on each network node, extensions to existing
signaling or routing protocols are needed in order to carry the
necessary information for avoiding allocating shared protection
resources for two non-disjoint working LSPs. However, stateful PCE(s)
can easily accommodate this need using the information stored in its
LSP-DB, without requiring extensions to existing routing protocols.
Zhang Expires January 2013 [Page 12]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
+----+
|PCE |
+----+
+------+ +------+ +------+
| N1 +----------+ N2 +----------+ N3 |
+--+---+ +---+--+ +---+--+
| | |
| +---------+ |
| | |
| +--+---+ +------+ |
+-----+ N5 +----------+ N4 +-----+
+------+ +------+
Figure 2: Example Network
For example, in the network depicted in Figure 2, suppose there
exists LSP1 (N1->N5) with backup route following N1->N2->N5. A
request arrives asking for a working and backup path pair to be
computed for a request from N2 to N5. If the PCE decides N2->N1->N5
to be the best working route, then the backup path should not use
the same protection resource with LSP1 since the new LSP shares part
of its resource with LSP1 (i.e., these two LSPs are in the same
shared risk group). Alternatively, there is no such constraint if
N2->N3->N4->N5 is chosen to be the right candidate for undertaking
the request.
3.3.2. Restoration
In case of a link failure, such as fiber cut, multiple LSPs may fail
at the same time. Thus, the source nodes of the affected LSPs will
be informed of the failure by the nodes detecting the failure. These
source nodes will send requests to a PCE for rerouting. In order to
reuse the resource taken by an existing LSP, the source node can
send a PCReq message including the XRO object with F bit set,
together with RRO object, as specified in [RFC5521].
If a stateless PCE is exploited, it might respond to the rerouting
requests separately if they arrive at different times. Thus, it
might result in sub-optimal resource usage. Even worse, it might
unnecessarily block some of the rerouting requests due to
insufficient resources for later-arrived rerouting messages. If a
stateful PCE is used to fulfill this task, it can re-compute the
affected LSPs concurrently while reusing part of the existing LSPs
resources when it is informed of the failed link identifier provided
by the first request. This is made possible since the stateful PCE
can check what other LSPs are affected by the failed link and their
Zhang Expires January 2013 [Page 13]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
route information by inspecting its LSP-DB. As a result, a better
performance, such as better resource usage, minimal probability of
blocking upcoming new rerouting requests sent as a result of the
link failure, can be achieved.
In order to further reduce the amount of LSP rerouting messages flow
in the network, the notification can be performed at the node(s)
which detect the link failure. For example, suppose there are two
LSPs in the network as shown in Figure 2: (i) LSP1: N1->N5->N4->N3;
(ii) LSP2: N2->N5->N4. They traverse the failed link between N5-N4.
When N4 detects the failure, it can send a notification message to a
stateful PCE. Note that the stateful PCE stores the path information
of the LSPs that are affected by the link failure, so it does not
need to acquire this information from N4. Moreover, it can make use
of the bandwidth resources occupied by the affected LSPs when
performing path recalculation. After N4 receives the new paths from
the PCE, it notifies the ingress nodes of the LSPs, i.e., N1 and N2,
and specifies the new paths which should be used as the rerouting
paths. To support this, it would require extensions to existing
signaling protocol.
Alternatively, if the target is to avoid resource contention within
the time-window of high LSP requests, a stateful PCE can retain the
under-construction LSP resource usage information for a given time
and exclude it from being used for forthcoming LSPs' request. In
this way, it can ensure that the resource will not be double-booked
and thus the issue of resource contention and computation crank-
backs can be resolved.
3.4. SRLG Diversity
A common requirement is to maintain SRLG disjointness between LSPs.
This can be achieved at provisioning time, if the routes of all the
LSPs are requested together, using a synchronized computation of the
different LSPs with SRLG disjointness constraint. If the LSPs need
to be provisioned at different times, (more general, the routes are
requested at different times, e.g. in the case of a restoration),
the PCC can specify, as constraints to the path computation a set of
Shared Risk Link Groups (SRLGs) using the Explicit route Object [RFC
5521]. However, for the latter to be effective, it is needed that
the entity that requests the route to the PCE maintains updated SRLG
information of all the LSPs to which it must maintain the
disjointness.
Using a stateful PCE allows the maintenance of the updated SRLG
information of the established LSPs in the PCEa centralized manner.
Zhang Expires January 2013 [Page 14]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
Having such information in the PCE facilitates the PCC to specify,
as constraint to the path computation, the SRLG disjointess of a set
of already established LSPs by only providing LSPs' identifiers.
3.5. Maintenance of Virtual Network Topology (VNT)
In Multi-Layer Networks (MLN), a Virtual Network Topology (VNT)
[RFC5212] consists of a set of one or more TE LSPs in the lower
layer to provide TE links to the upper layer. In [RFC5623], the PCE-
based architecture is proposed to support path computation in MLN
networks in order to achieve inter-layer TE.
The establishment/teardown of a TE link in VNT needs to take into
consideration the state of existing LSPs and/or new LSP request(s)
in the higher layer. Traditionally, a VNT manager (VNTM) is in
charge of the topology in the upper layer by connections in the
lower layer. Hence, when a stateless PCE is requested to compute a
new TE link, it will need interaction with VNTM for detailed TE link
information. To be more specific, wWithout detailed LSP information,
this process would be inefficient or even infeasible for stateless
PCE(s), unless with , requiring the cooperation of a NMS or a VNT
cooperation with VNTMmanager (VNTM). On the other hand, Therefore, a
stateful PCE seems more suitable to make the decision of when and
how to modify the VNT either to accommodate new LSP requests or to
re-optimize resource use across layers irrespective of PCE models.
As described in Section 2.2, path computation for a VNT change can
be performed by the PCE if a single PCE model is adopted. On the
other hand, if a per-layer PCE model is more appropriate,
coordination between PCEs is required.
3.6. Global Concurrent Optimization (GCO)
GCO is introduced in [RFC5557] to calculate multiple paths
concurrently so as to improve network resource efficiency. By taking
into consideration the network topology as well as existing TE LSPs
information, GCO can (re)optimize the entire network simultaneously.
Alternatively, GCO can be applied to (re)optimize one or a subset of
existing TE LSPs or plan for forthcoming LSP(s) with specific
objectives. GCO can also support off-line one-time optimization
(i.e., planning) given a traffic matrix and network topology. Due to
its complexity and potentially high computational demand, it is
recommended to be performed in a centralized way (e.g., based on a
management-based PCE).
In case of a stateless PCE, in order to optimize network resource
usage dynamically through online planning, PCC (e.g., NMS) should
send a request to PCE together with detailed path/bandwidth
information of the LSPs that need to be concurrently optimized. This
Zhang Expires January 2013 [Page 15]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
would require a PCC (e.g., NMS) to determine when and which LSPs
should be optimized. Given all of the existing LSP state information
kept at a stateful PCE, it allows automation of this process without
the PCC (e.g. NMS) to supply the existing LSP state information.
Moreover, since a stateful PCE can maintain the information
regarding to all LSPs that are currently under signaling, it makes
the optimization procedures be performed more intelligently and
effectively.
3.7. Point-to-Multipoint (P2MP) Application
Route computation for P2MP application involves selection of
branching points together with calculating multiple sub-LSPs with
certain objective(s) such as minimizing the overall cost of the P2MP
tree. Moreover, egress nodes addition and removal in a P2MP tree
necessitates (re)optimization. Besides these, there are also some
constraints and policies that make the P2MP tree computation hard,
requiring high computation power. Therefore, PCE is proposed to
support P2MP application [RFC5671].
If a stateless PCE is used for P2MP calculation or optimization
under constraints such as load balancing or path disjointedness,
then a large amount of sub-LSP information might need to be
exchanged between the PCE and the requesting entities. Moreover, if
the requesting entity cannot provide complete information of sub-
LSPs pertaining to the P2MP tree, then the performance of stateless
PCE will be sub-optimal. On the contrary, a stateful PCE can support
the P2MP tree computation/optimization with reduced overhead and
improved efficiency.
3.8. Time-based Scheduling
Time-based scheduling allows network operators to reserve resources
in advance upon request from the customers to transmit large bulk of
data with specified starting time and duration, such as in support
of scheduled data transmission between data centers.
Traditionally, this can be supported by NMS operation through path
pre-establishment and activation on the agreed starting time.
However, this does not provide efficient network usage since the
established paths exclude the possibility of being used by other
services even when they are not used for undertaking any service. It
can also be accomplished through GMPLS protocol extensions by
carrying the related request information (e.g., starting time and
duration) across the network. Nevertheless, this method inevitably
increases the complexity of signaling and routing process.
Zhang Expires January 2013 [Page 16]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
A stateful PCE can support this application with better efficiency
since it can alleviate the burden of processing on network elements
as well as enable the flexibility of resources usage by only
excluding the time slot(s) reserved for time-based scheduling
requests. In order to support this application, a stateful PCE
should also maintain a database that stores all the reserved
information with time reference. This can be achieved either by
maintaining a separate database or incorporated into LSP-DB. The
details of organizing time-based scheduling related information as
well as its impact on LSP-DB is subject to network provider's policy
and administrative consideration and thus outside of the scope of
this document.
4. Manageability Considerations
The description and functionality specifications presented related
to stateful PCE(s) should also comply with the manageability
specifications covered in Section 8 of [RFC4655]. Furthermore, a
further list of manageability issues presented in [Stateful-PCEP-
mpls] may also be considered.
4.1. Information and Data Models
A Management Information Base (MIB) module for management of the
PCEP is being specified in a separate document [PCEP-MIB]. That MIB
module allows examination of individual PCEP messages, in particular
requests, responses and errors. The MIB module MUST be extended to
include the ability to view stateful PCE PCEP extensions defined in
relevant documents.
5. Security Considerations
The security issues presented in [RFC5440] still applies to this
document. In addition, the security concerns raised by [Stateful-
PCEP-mpls] may also be considered.
6. References
6.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to indicate
requirements levels", RFC 2119, March 1997.
[RFC4655] Farrel, A., Vasseur, J.-P., and Ash, J., "A Path
Computation Element (PCE)-Based Architecture", RFC 4655,
August 2006.
Zhang Expires January 2013 [Page 17]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
[RFC5440] Vasseur, J.-P., and Le Roux, JL., "Path Computation
Element (PCE) Communication Protocol (PCEP)", RFC 5440,
March 2009.
[RFC6163] Lee, Y., Bernstein, G., "Framework for GMPLS and Path
Computation Element (PCE) Control of Wavelength Switched
Optical Networks (WSONs)", RFC 6163, April, 2011.
[RFC5521] Oki, E., Farrel, A., "Extensions to the Path Computation
Element Communication Protocol (PCEP) for Route
Exclusions", RFC5521, April 2009.
6.2. Informative References
[WSON-Impairment] Lee, Y., Bernstein, G., Li, D., Martinelli, G., "A
Framework for the Control of Wavelength Switched Optical
Network (WSON) with Impairments", draft-ietf-ccamp-wson-
impairments, work in progress.
[RFC4726] Farrel, A., Vasseur, J.-P., Ayyangar, A., "A Framework for
Inter-Domain Multiprotocol Label Switching Traffic
Engineering", RFC 4726, November 2006.
[RFC5520] Bradford, R., Vasseur, JP., Farrel, A., "Preserving
Topology Confidentiality in Inter-Domain Path Computation
Using a Path-Key-Based Mechanism", RFC 5520, April 2009.
[RFC5441] Vasseur, J.-P., Zhang, R., Bitar, N., Le Roux, JL., "A
Backward-Recursive PCE-Based Computation (BRPC) Procedure
to Compute Shortest Constrained Inter-Domain Traffic
Engineering Label Switched Paths", RFC 5441, April 2009.
[PSU-WSON] Giorgetti, A, Cugini, G, et al, "Path state-based update
of PCE traffic engineering database in wavelength switched
optical networks", IEEE Com. Let., June 2010.
[LCA-Stateless] Gonzalez de Dios, O., et al, "Benefits of limited
context awareness in stateless PCE", Optical Fiber
Communication Conference, March 2011.
[WSON-OSPF] Lee, Y., Bernstein, G., "GMPLS OSPF Enhancement for
Signal and Network Element Compatibility for Wavelength
Switched Optical Networks", draft-ietf-ccamp-wson-signal-
compatibility-ospf-07, October 2011.
Zhang Expires January 2013 [Page 18]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
[GEN-OSPF] Zhang, Fatai, Lee, Y., Han, Jianrui, Bernstein, G., Xu,
Yunbin, "OSPF-TE Extensions for General Network Element
Constraints", draft-ietf-ccamp-gmpls-general-constraints-
ospf-te-02, September 2011.
[G.FLEXIGRID] Draft revised G.694.1 version 1.3, Unpublished ITU-T
Study Group 15, Question 6.
[RFC5212] Shiomoto, K., Papadimitriou, D., Le Roux, JL., Vigoureux,
M., Brungard, D., "Requirements for GMPLS-Based Multi-
Region and Multi-Layer Networks (MRN/MLN)", RFC 5212, July
2008.
[RFC5557] Lee, Y., Le Roux, JL., King, D., Oki E., "Path Computation
Element Communication Protocol (PCEP) Requirements and
Protocol Extensions in Support of Global Concurrent
Optimization", RFC 5557, July, 2009.
[RFC5671] Yasukawa, S., Farrel, A., "Applicability of the Path
Computation Element (PCE) to Point-to-Multipoint (P2MP)
MPLS and GMPLS Traffic Engineering (TE)", October, 2009.
[RFC5623] Oki, E., Takeda, T., Le Roux, JL., Farrel, A., "Framework
for PCE-Based Inter-Layer MPLS and GMPLS Traffic
Engineering", RFC5623, September 2009.
[stateful-PCEP-mpls] Crabbe, E., Medved, J., Varga, R., Minei, I.,
''PCEP Extensions for Stateful PCE'', draft-ietf-pce-
stateful-pce, work in progress.
[stateful-PCEP-gmpls] Zhang, X., Lee, Y., Casellas, R., Gonzalez de
Dios, O., '' Path Computation Element (PCE) Protocol
Extension for Stateful PCE Usage in GMPLS Networks'',
draft-zhang-pce-pcep-stateful-pce-gmpls, work in progress.
[PCEP-MIB] Kiran Koushik, A S., Stephan, E., Zhao, Q., King, D.,
"PCE communication protocol (PCEP) Management Information
Base", draft-ietf-pce-pcep-mib, work in progress.
Zhang Expires January 2013 [Page 19]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
7. Contributors' Address
Dhruv Dhody
Huawei Technology
Leela Palace
Bangalore, Karnataka 560008
INDIA
EMail: dhruvd@huawei.com
Xiaobing Zi
Huawei Technologies
F3-5-B R&D Center, Huawei Base
Bantian, Longgang District
Shenzhen 518129 P.R.China
Phone: +86-755-28973229
Email: zixiaobing@huawei.com
Authors' Addresses
Fatai Zhang
Huawei Technologies
F3-5-B R&D Center, Huawei Base
Bantian, Longgang District
Shenzhen 518129 P.R.China
Phone: +86-755-28972912
Email: zhangfatai@huawei.com
Xian Zhang
Huawei Technologies
F3-5-B R&D Center, Huawei Base
Bantian, Longgang District
Shenzhen 518129 P.R.China
Phone: +86-755-28972913
Email: zhang.xian@huawei.com
Young Lee
Huawei
1700 Alma Drive, Suite 100
Zhang Expires January 2013 [Page 20]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
Plano, TX 75075
US
Phone: +1 972 509 5599 x2240
Fax: +1 469 229 5397
EMail: ylee@huawei.com
Ramon Casellas
CTTC - Centre Tecnologic de Telecomunicacions de Catalunya
Av. Carl Friedrich Gauss n7
Castelldefels, Barcelona 08860
Spain
Phone:
Email: ramon.casellas@cttc.es
Oscar Gonzalez de Dios
Telefonica Investigacion y Desarrollo
Emilio Vargas 6
Madrid, 28045
Spain
Phone: +34 913374013
Email: ogondio@tid.es
Intellectual Property
The IETF Trust takes no position regarding the validity or scope of
any Intellectual Property Rights or other rights that might be
claimed to pertain to the implementation or use of the technology
described in any IETF Document or the extent to which any license
under such rights might or might not be available; nor does it
represent that it has made any independent effort to identify any
such rights.
Copies of Intellectual Property disclosures made to the IETF
Secretariat and any assurances of licenses to be made available, or
the result of an attempt made to obtain a general license or
permission for the use of such proprietary rights by implementers or
users of this specification can be obtained from the IETF on-line
IPR repository at http://www.ietf.org/ipr
Zhang Expires January 2013 [Page 21]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
any standard or specification contained in an IETF Document. Please
address the information to the IETF at ietf-ipr@ietf.org.
The definitive version of an IETF Document is that published by, or
under the auspices of, the IETF. Versions of IETF Documents that are
published by third parties, including those that are translated into
other languages, should not be considered to be definitive versions
of IETF Documents. The definitive version of these Legal Provisions
is that published by, or under the auspices of, the IETF. Versions
of these Legal Provisions that are published by third parties,
including those that are translated into other languages, should
not be considered to be definitive versions of these Legal
Provisions.
For the avoidance of doubt, each Contributor to the IETF Standards
Process licenses each Contribution that he or she makes as part of
the IETF Standards Process to the IETF Trust pursuant to the
provisions of RFC 5378. No language to the contrary, or terms,
conditions or rights that differ from or are inconsistent with the
rights and licenses granted under RFC 5378, shall have any effect
and shall be null and void, whether published or posted by such
Contributor, or included with or in such Contribution.
Disclaimer of Validity
All IETF Documents and the information contained therein are
provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION
HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET
SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE
DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION THEREIN
WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Full Copyright Statement
Copyright (c) 2012 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
Zhang Expires January 2013 [Page 22]
draft-zhang-pce-stateful-pce-app-01.txt July 2012
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Zhang Expires January 2013 [Page 23]