Skip to main content

Hash-Based Signatures
draft-mcgrew-hash-sigs-11

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8554.
Authors David McGrew , Michael Curcio , Scott Fluhrer
Last updated 2018-07-28 (Latest revision 2018-04-06)
RFC stream Internet Research Task Force (IRTF)
Formats
IETF conflict review conflict-review-mcgrew-hash-sigs, conflict-review-mcgrew-hash-sigs, conflict-review-mcgrew-hash-sigs, conflict-review-mcgrew-hash-sigs, conflict-review-mcgrew-hash-sigs, conflict-review-mcgrew-hash-sigs
Additional resources Mailing list discussion
Stream IRTF state Waiting for Document Shepherd
Consensus boilerplate Yes
Document shepherd Paul E. Hoffman
IESG IESG state Became RFC 8554 (Informational)
Telechat date (None)
Responsible AD (None)
Send notices to paul.hoffman@vpnc.org, cfrg-chairs@irtf.org, Paul Hoffman <paul.hoffman@icann.org>
draft-mcgrew-hash-sigs-11
Crypto Forum Research Group                                    D. McGrew
Internet-Draft                                                 M. Curcio
Intended status: Informational                                S. Fluhrer
Expires: October 7, 2018                                   Cisco Systems
                                                           April 5, 2018

                         Hash-Based Signatures
                       draft-mcgrew-hash-sigs-11

Abstract

   This note describes a digital signature system based on cryptographic
   hash functions, following the seminal work in this area of Lamport,
   Diffie, Winternitz, and Merkle, as adapted by Leighton and Micali in
   1995.  It specifies a one-time signature scheme and a general
   signature scheme.  These systems provide asymmetric authentication
   without using large integer mathematics and can achieve a high
   security level.  They are suitable for compact implementations, are
   relatively simple to implement, and naturally resist side-channel
   attacks.  Unlike most other signature systems, hash-based signatures
   would still be secure even if it proves feasible for an attacker to
   build a quantum computer.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on October 7, 2018.

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents

McGrew, et al.           Expires October 7, 2018                [Page 1]
Internet-Draft            Hash-Based Signatures               April 2018

   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Conventions Used In This Document . . . . . . . . . . . .   4
   2.  Interface . . . . . . . . . . . . . . . . . . . . . . . . . .   5
   3.  Notation  . . . . . . . . . . . . . . . . . . . . . . . . . .   5
     3.1.  Data Types  . . . . . . . . . . . . . . . . . . . . . . .   5
       3.1.1.  Operators . . . . . . . . . . . . . . . . . . . . . .   6
       3.1.2.  Functions . . . . . . . . . . . . . . . . . . . . . .   6
       3.1.3.  Strings of w-bit elements . . . . . . . . . . . . . .   7
     3.2.  Typecodes . . . . . . . . . . . . . . . . . . . . . . . .   8
   4.  LM-OTS One-Time Signatures  . . . . . . . . . . . . . . . . .   8
     4.1.  Parameters  . . . . . . . . . . . . . . . . . . . . . . .   8
     4.2.  Private Key . . . . . . . . . . . . . . . . . . . . . . .   9
     4.3.  Public Key  . . . . . . . . . . . . . . . . . . . . . . .  10
     4.4.  Checksum  . . . . . . . . . . . . . . . . . . . . . . . .  11
     4.5.  Signature Generation  . . . . . . . . . . . . . . . . . .  12
     4.6.  Signature Verification  . . . . . . . . . . . . . . . . .  13
   5.  Leighton-Micali Signatures  . . . . . . . . . . . . . . . . .  14
     5.1.  Parameters  . . . . . . . . . . . . . . . . . . . . . . .  15
     5.2.  LMS Private Key . . . . . . . . . . . . . . . . . . . . .  15
     5.3.  LMS Public Key  . . . . . . . . . . . . . . . . . . . . .  16
     5.4.  LMS Signature . . . . . . . . . . . . . . . . . . . . . .  17
       5.4.1.  LMS Signature Generation  . . . . . . . . . . . . . .  18
       5.4.2.  LMS Signature Verification  . . . . . . . . . . . . .  19
   6.  Hierarchical signatures . . . . . . . . . . . . . . . . . . .  21
     6.1.  Key Generation  . . . . . . . . . . . . . . . . . . . . .  22
     6.2.  Signature Generation  . . . . . . . . . . . . . . . . . .  23
     6.3.  Signature Verification  . . . . . . . . . . . . . . . . .  25
   7.  Formats . . . . . . . . . . . . . . . . . . . . . . . . . . .  25
   8.  Rationale . . . . . . . . . . . . . . . . . . . . . . . . . .  28
     8.1.  Security string . . . . . . . . . . . . . . . . . . . . .  29
   9.  History . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
   10. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  32
   11. Intellectual Property . . . . . . . . . . . . . . . . . . . .  34
     11.1.  Disclaimer . . . . . . . . . . . . . . . . . . . . . . .  34
   12. Security Considerations . . . . . . . . . . . . . . . . . . .  34
     12.1.  Hash Formats . . . . . . . . . . . . . . . . . . . . . .  35
     12.2.  Stateful signature algorithm . . . . . . . . . . . . . .  36
     12.3.  Security of LM-OTS Checksum  . . . . . . . . . . . . . .  37

McGrew, et al.           Expires October 7, 2018                [Page 2]
Internet-Draft            Hash-Based Signatures               April 2018

   13. Comparison with other work  . . . . . . . . . . . . . . . . .  38
   14. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  38
   15. References  . . . . . . . . . . . . . . . . . . . . . . . . .  38
     15.1.  Normative References . . . . . . . . . . . . . . . . . .  38
     15.2.  Informative References . . . . . . . . . . . . . . . . .  39
   Appendix A.  Pseudorandom Key Generation  . . . . . . . . . . . .  40
   Appendix B.  LM-OTS Parameter Options . . . . . . . . . . . . . .  41
   Appendix C.  An iterative algorithm for computing an LMS public
                key  . . . . . . . . . . . . . . . . . . . . . . . .  42
   Appendix D.  Method for deriving authentication path for a
                signature  . . . . . . . . . . . . . . . . . . . . .  43
   Appendix E.  Example Implementation . . . . . . . . . . . . . . .  44
   Appendix F.  Parameter Set Recommendations  . . . . . . . . . . .  44
   Appendix G.  Test Cases . . . . . . . . . . . . . . . . . . . . .  45
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  57

1.  Introduction

   One-time signature systems, and general purpose signature systems
   built out of one-time signature systems, have been known since 1979
   [Merkle79], were well studied in the 1990s [USPTO5432852], and have
   benefited from renewed attention in the last decade.  The
   characteristics of these signature systems are small private and
   public keys and fast signature generation and verification, but large
   signatures and moderately slow key generation (in comparison with RSA
   and ECDSA).  Private keys can be made very small by appropriate key
   generation, for example, as described in Appendix A.  In recent years
   there has been interest in these systems because of their post-
   quantum security and their suitability for compact verifier
   implementations.

   This note describes the Leighton and Micali adaptation [USPTO5432852]
   of the original Lamport-Diffie-Winternitz-Merkle one-time signature
   system [Merkle79] [C:Merkle87][C:Merkle89a][C:Merkle89b] and general
   signature system [Merkle79] with enough specificity to ensure
   interoperability between implementations.

   A signature system provides asymmetric message authentication.  The
   key generation algorithm produces a public/private key pair.  A
   message is signed by a private key, producing a signature, and a
   message/signature pair can be verified by a public key.  A One-Time
   Signature (OTS) system can be used to sign one message securely, but
   will become insecure if more than one is signed with the same public/
   private key pair.  An N-time signature system can be used to sign N
   or fewer messages securely.  A Merkle tree signature scheme is an
   N-time signature system that uses an OTS system as a component.

McGrew, et al.           Expires October 7, 2018                [Page 3]
Internet-Draft            Hash-Based Signatures               April 2018

   In the Merkle scheme, a binary tree of height h is used to hold 2^h
   OTS key pairs.  Each interior node of the tree holds a value which is
   the hash of the values of its two children nodes.  The public key of
   the tree is the value of the root node (a recursive hash of the OTS
   public keys), while the private key of the tree is the collection of
   all the OTS private keys, together with the index of the next OTS
   private key to sign the next message with.

   In this note we describe the Leighton-Micali Signature (LMS) system,
   which is a variant of the Merkle scheme, and a Hierarchical Signature
   System (HSS) built on top of it that can efficiently scale to larger
   numbers of signatures.  In order to support signing a large number of
   messages on resource constrained systems, the Merkle tree can be
   subdivided into a number of smaller trees.  Only the bottom-most tree
   is used to sign messages, while trees above that are used to sign the
   public keys of their children.  For example, in the simplest case
   with 2 levels with both levels consisting of height h trees, the root
   tree is used to sign 2^h trees with 2^h OTS key pairs, and each
   second level tree has 2^h OTS key pairs, for a total of 2^(2h) bottom
   level key pairs, and so can sign 2^(2h) messages.  The advantage of
   this scheme is that only the active trees need to be instantiated,
   which saves both time (for key generation) and space (for key
   storage).  On the other hand, using a multilevel signature scheme
   inceases the size of the signature, as well as the signature
   verification time.

   This note is structured as follows.  Notation is introduced in
   Section 3.  The LM-OTS signature system is described in Section 4,
   and the LMS and HSS N-time signature systems are described in
   Section 5 and Section 6, respectively.  Sufficient detail is provided
   to ensure interoperability.  The public formats are described in
   Section 7.  The rationale for design decisions are given in
   Section 8.  The changes made to this document over previous versions
   is listed in Section 9.  The IANA registry for these signature
   systems is described in Section 10.  Intellectual Property issues are
   discussed in Section 11.  Security considerations are presented in
   Section 12.

1.1.  Conventions Used In This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

McGrew, et al.           Expires October 7, 2018                [Page 4]
Internet-Draft            Hash-Based Signatures               April 2018

2.  Interface

   The LMS signing algorithm is stateful; it modifies and updates the
   private key as a side effect of generating a signature.  Once a
   particular value of the private key is used to sign one message, it
   MUST NOT be used to sign another.

   The key generation algorithm takes as input an indication of the
   parameters for the signature system.  If it is successful, it returns
   both a private key and a public key.  Otherwise, it returns an
   indication of failure.

   The signing algorithm takes as input the message to be signed and the
   current value of the private key.  If successful, it returns a
   signature and the next value of the private key, if there is such a
   value.  After the private key of an N-time signature system has
   signed N messages, the signing algorithm returns the signature and an
   indication that there is no next value of the private key that can be
   used for signing.  If unsuccessful, it returns an indication of
   failure.

   The verification algorithm takes as input the public key, a message,
   and a signature, and returns an indication of whether or not the
   signature and message pair is valid.

   A message/signature pair is valid if the signature was returned by
   the signing algorithm upon input of the message and the private key
   corresponding to the public key; otherwise, the signature and message
   pair is not valid with probability very close to one.

3.  Notation

3.1.  Data Types

   Bytes and byte strings are the fundamental data types.  A single byte
   is denoted as a pair of hexadecimal digits with a leading "0x".  A
   byte string is an ordered sequence of zero or more bytes and is
   denoted as an ordered sequence of hexadecimal characters with a
   leading "0x".  For example, 0xe534f0 is a byte string with a length
   of three.  An array of byte strings is an ordered set, indexed
   starting at zero, in which all strings have the same length.

   Unsigned integers are converted into byte strings by representing
   them in network byte order.  To make the number of bytes in the
   representation explicit, we define the functions u8str(X), u16str(X),
   and u32str(X), which take a non-negative integer X as input and
   return one, two, and four byte strings, respectively.  We also make
   use of the function strTou32(S), which takes a four-byte string S as

McGrew, et al.           Expires October 7, 2018                [Page 5]
Internet-Draft            Hash-Based Signatures               April 2018

   input and returns a non-negative integer; the identity
   u32str(strTou32(S)) = S holds for any four-byte string S.

3.1.1.  Operators

   When a and b are real numbers, mathematical operators are defined as
   follows:

      ^ : a ^ b denotes the result of a raised to the power of b

      * : a * b denotes the product of a multiplied by b

      / : a / b denotes the quotient of a divided by b

      % : a % b denotes the remainder of the integer division of a by b

      + : a + b denotes the sum of a and b

      - : a - b denotes the difference of a and b

   The standard order of operations is used when evaluating arithmetic
   expressions.

   When B is a byte and i is an integer, then B >> i denotes the logical
   right-shift operation by i positions.  Similarly, B << i denotes the
   logical left-shift operation.

   If S and T are byte strings, then S || T denotes the concatenation of
   S and T.  If S and T are equal length byte strings, then S AND T
   denotes the bitwise logical and operation.

   The i-th element in an array A is denoted as A[i].

3.1.2.  Functions

   If r is a non-negative real number, then we define the following
   functions:

      ceil(r) : returns the smallest integer larger than r

      floor(r) : returns the largest integer smaller than r

      lg(r) : returns the base-2 logarithm of r

McGrew, et al.           Expires October 7, 2018                [Page 6]
Internet-Draft            Hash-Based Signatures               April 2018

3.1.3.  Strings of w-bit elements

   If S is a byte string, then byte(S, i) denotes its i-th byte, where
   byte(S, 0) is the leftmost byte.  In addition, bytes(S, i, j) denotes
   the range of bytes from the i-th to the j-th byte, inclusive.  For
   example, if S = 0x02040608, then byte(S, 0) is 0x02 and bytes(S, 1,
   2) is 0x0406.

   A byte string can be considered to be a string of w-bit unsigned
   integers; the correspondence is defined by the function coef(S, i, w)
   as follows:

   If S is a string, i is a positive integer, and w is a member of the
   set { 1, 2, 4, 8 }, then coef(S, i, w) is the i-th, w-bit value, if S
   is interpreted as a sequence of w-bit values.  That is,

       coef(S, i, w) = (2^w - 1) AND
                       ( byte(S, floor(i * w / 8)) >>
                         (8 - (w * (i % (8 / w)) + w)) )

   For example, if S is the string 0x1234, then coef(S, 7, 1) is 0 and
   coef(S, 0, 4) is 1.

                      S (represented as bits)
         +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
         | 0| 0| 0| 1| 0| 0| 1| 0| 0| 0| 1| 1| 0| 1| 0| 0|
         +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
                                ^
                                |
                          coef(S, 7, 1)

                 S (represented as four-bit values)
         +-----------+-----------+-----------+-----------+
         |     1     |     2     |     3     |     4     |
         +-----------+-----------+-----------+-----------+
               ^
               |
         coef(S, 0, 4)

   The return value of coef is an unsigned integer.  If i is larger than
   the number of w-bit values in S, then coef(S, i, w) is undefined, and
   an attempt to compute that value should raise an error.

McGrew, et al.           Expires October 7, 2018                [Page 7]
Internet-Draft            Hash-Based Signatures               April 2018

3.2.  Typecodes

   A typecode is an unsigned integer that is associated with a
   particular data format.  The format of the LM-OTS, LMS, and HSS
   signatures and public keys all begin with a typecode that indicates
   the precise details used in that format.  These typecodes are
   represented as four-byte unsigned integers in network byte order;
   equivalently, they are XDR enumerations (see Section 7).

4.  LM-OTS One-Time Signatures

   This section defines LM-OTS signatures.  The signature is used to
   validate the authenticity of a message by associating a secret
   private key with a shared public key.  These are one-time signatures;
   each private key MUST be used at most one time to sign any given
   message.

   As part of the signing process, a digest of the original message is
   computed using the cryptographic hash function H (see Section 4.1),
   and the resulting digest is signed.

   In order to facilitate its use in an N-time signature system, the LM-
   OTS key generation, signing, and verification algorithms all take as
   input a parameter q, which indicates the leaf of the Merkle tree
   where the OTS public key appears.  This parameter is used as part of
   the security string, as listed in Section 8.1.  When the LM-OTS
   signature system is used outside of an N-time signature system, this
   value SHOULD be set to the all-zero value.

4.1.  Parameters

   The signature system uses the parameters n and w, which are both
   positive integers.  The algorithm description also makes use of the
   internal parameters p and ls, which are dependent on n and w.  These
   parameters are summarized as follows:

      n : the number of bytes of the output of the hash function

      w : the width (in bits) of the Winternitz coefficients; it is a
      member of the set { 1, 2, 4, 8 }

      p : the number of n-byte string elements that make up the LM-OTS
      signature

      ls : the number of left-shift bits used in the checksum function
      Cksm (defined in Section 4.4)

McGrew, et al.           Expires October 7, 2018                [Page 8]
Internet-Draft            Hash-Based Signatures               April 2018

      H : a second-preimage-resistant cryptographic hash function that
      accepts byte strings of any length, and returns an n-byte string

   For more background on the cryptographic security requirements on H,
   see the Section 12.

   The value of n is determined by the hash function selected for use as
   part of the LM-OTS algorithm; the choice of this value has a strong
   effect on the security of the system.  The parameter w determines the
   length of the Winternitz chains computed as a part of the OTS
   signature (which involve 2^w-1 invocations of the hash function); it
   has little effect on security.  Increasing w will shorten the
   signature, but at a cost of a larger computation to generate and
   verify a signature.  The values of p and ls are dependent on the
   choices of the parameters n and w, as described in Appendix B.  A
   table illustrating various combinations of n, w, p, and ls is
   provided in Table 1.

   The value of w describes a space/time trade-off; increasing the value
   of w will cause the signature to shrink (by decreasing the value of
   p) while increasing the amount of time needed to perform operations
   with it (generate the public key, generate and verify the signature);
   in general, the LM-OTS signature is 4+n*(p+1) bytes long, and public
   key generation will take p*(2^w-1)+1 hash computations (and signature
   generation and verification will take about half that on average).

           +---------------------+--------+----+---+-----+----+
           | Name                | H      | n  | w | p   | ls |
           +---------------------+--------+----+---+-----+----+
           | LMOTS_SHA256_N32_W1 | SHA256 | 32 | 1 | 265 | 7  |
           |                     |        |    |   |     |    |
           | LMOTS_SHA256_N32_W2 | SHA256 | 32 | 2 | 133 | 6  |
           |                     |        |    |   |     |    |
           | LMOTS_SHA256_N32_W4 | SHA256 | 32 | 4 | 67  | 4  |
           |                     |        |    |   |     |    |
           | LMOTS_SHA256_N32_W8 | SHA256 | 32 | 8 | 34  | 0  |
           +---------------------+--------+----+---+-----+----+

                                  Table 1

   Here SHA256 denotes the SHA-256 hash fucntion defined in NIST
   standard [FIPS180].

4.2.  Private Key

   The format of the LM-OTS private key is an internal matter to the
   implementation, and this document does not attempt to define it.  One
   possibility is that the private key may consist of a typecode

McGrew, et al.           Expires October 7, 2018                [Page 9]
Internet-Draft            Hash-Based Signatures               April 2018

   indicating the particular LM-OTS algorithm, an array x[] containing p
   n-byte strings, and the 16-byte string I and the 4 byte string q.
   This private key MUST be used to sign (at most) one message.  The
   following algorithm shows pseudocode for generating a private key.

   Algorithm 0: Generating a Private Key

  1. retrieve the values of q and I (the 16-byte
     identifier of the LMS public/private keypair) from the LMS tree that this LM-OTS private
     key will be used with

  2. set type to the typecode of the algorithm

  3. set n and p according to the typecode and Table 1

  4. compute the array x as follows:
     for ( i = 0; i < p; i = i + 1 ) {
       set x[i] to a uniformly random n-byte string
     }

  5. return u32str(type) || I || u32str(q) || x[0] || x[1] || ... || x[p-1]

   An implementation MAY use a pseudorandom method to compute x[i], as
   suggested in [Merkle79], page 46.  The details of the pseudorandom
   method do not affect interoperability, but the cryptographic strength
   MUST match that of the LM-OTS algorithm.  Appendix A provides an
   example of a pseudorandom method for computing the LM-OTS private
   key.

4.3.  Public Key

   The LM-OTS public key is generated from the private key by
   iteratively applying the function H to each individual element of x,
   for 2^w - 1 iterations, then hashing all of the resulting values.

   The public key is generated from the private key using the following
   algorithm, or any equivalent process.

McGrew, et al.           Expires October 7, 2018               [Page 10]
Internet-Draft            Hash-Based Signatures               April 2018

   Algorithm 1: Generating a One Time Signature Public Key From a
   Private Key

   1. set type to the typecode of the algorithm

   2. set the integers n, p, and w according to the typecode and Table 1

   3. determine x, I and q from the private key

   4. compute the string K as follows:
      for ( i = 0; i < p; i = i + 1 ) {
        tmp = x[i]
        for ( j = 0; j < 2^w - 1; j = j + 1 ) {
           tmp = H(I || u32str(q) || u16str(i) || u8str(j) || tmp)
        }
        y[i] = tmp
      }
      K = H(I || u32str(q) || u16str(D_PBLC) || y[0] || ... || y[p-1])

   5. return u32str(type) || I || u32str(q) || K

   The public key is the value returned by Algorithm 1.

4.4.  Checksum

   A checksum is used to ensure that any forgery attempt that
   manipulates the elements of an existing signature will be detected.
   This checksum is needed because an attacker can freely advance any of
   the Winternitz chains.  That is, if this checksum were not present,
   then an attacker who could find a hash that has every digit larger
   than the valid hash could replace it (and adjust the Winternitz
   chains).  The security property that it provides is detailed in
   Section 12.  The checksum function Cksm is defined as follows, where
   S denotes the n-byte string that is input to that function, and the
   value sum is a 16-bit unsigned integer:

   Algorithm 2: Checksum Calculation

     sum = 0
     for ( i = 0; i < (n*8/w); i = i + 1 ) {
       sum = sum + (2^w - 1) - coef(S, i, w)
     }
     return (sum << ls)

   Because of the left-shift operation, the rightmost bits of the result
   of Cksm will often be zeros.  Due to the value of p, these bits will
   not be used during signature generation or verification.

McGrew, et al.           Expires October 7, 2018               [Page 11]
Internet-Draft            Hash-Based Signatures               April 2018

4.5.  Signature Generation

   The LM-OTS signature of a message is generated by first prepending
   the LMS key identifier I, the LMS leaf identifier q, the value D_MESG
   and the randomizer C to the message, then computing the hash, and
   then concatenating the checksum of the hash to the hash itself, then
   considering the resulting value as a sequence of w-bit values, and
   using each of the w-bit values to determine the number of times to
   apply the function H to the corresponding element of the private key.
   The outputs of the function H are concatenated together and returned
   as the signature.  The pseudocode for this procedure is shown below.

   Algorithm 3: Generating a One Time Signature From a Private Key and a
   Message

     1. set type to the typecode of the algorithm

     2. set n, p, and w according to the typecode and Table 1

     3. determine x, I and q from the private key

     4. set C to a uniformly random n-byte string

     5. compute the array y as follows:
        Q = H(I || u32str(q) || u16str(D_MESG) || C || message)
        for ( i = 0; i < p; i = i + 1 ) {
          a = coef(Q || Cksm(Q), i, w)
          tmp = x[i]
          for ( j = 0; j < a; j = j + 1 ) {
             tmp = H(I || u32str(q) || u16str(i) || u8str(j) || tmp)
          }
          y[i] = tmp
        }

      6. return u32str(type) || C || y[0] || ... || y[p-1]

   Note that this algorithm results in a signature whose elements are
   intermediate values of the elements computed by the public key
   algorithm in Section 4.3.

   The signature is the string returned by Algorithm 3.  Section 7
   specifies the typecode and more formally defines the encoding and
   decoding of the string.

McGrew, et al.           Expires October 7, 2018               [Page 12]
Internet-Draft            Hash-Based Signatures               April 2018

4.6.  Signature Verification

   In order to verify a message with its signature (an array of n-byte
   strings, denoted as y), the receiver must "complete" the chain of
   iterations of H using the w-bit coefficients of the string resulting
   from the concatenation of the message hash and its checksum.  This
   computation should result in a value that matches the provided public
   key.

   Algorithm 4a: Verifying a Signature and Message Using a Public Key

    1. if the public key is not at least four bytes long, return INVALID

    2. parse pubtype, I, q, and K from the public key as follows:
       a. pubtype = strTou32(first 4 bytes of public key)

       b. set n according to the pubkey and Table 1; if the public key
          is not exactly 24 + n bytes long, return INVALID

       c. I = next 16 bytes of public key

       d. q = strTou32(next 4 bytes of public key)

       e. K = next n bytes of public key

    3. compute the public key candidate Kc from the signature,
       message, and the identifiers I and q obtained from the
       public key, using Algorithm 4b.  If Algorithm 4b returns
       INVALID, then return INVALID.

    4. if Kc is equal to K, return VALID; otherwise, return INVALID

McGrew, et al.           Expires October 7, 2018               [Page 13]
Internet-Draft            Hash-Based Signatures               April 2018

   Algorithm 4b: Computing a Public Key Candidate Kc from a Signature,
   Message, Signature Typecode Type, and identifiers I, q

  1. if the signature is not at least four bytes long, return INVALID

  2. parse sigtype, C, and y from the signature as follows:
     a. sigtype = strTou32(first 4 bytes of signature)

     b. if sigtype is not equal to pubtype, return INVALID

     c. set n and p according to the pubtype and Table 1;  if the
     signature is not exactly 4 + n * (p+1) bytes long, return INVALID

     d. C = next n bytes of signature

     e.  y[0] = next n bytes of signature
         y[1] = next n bytes of signature
         ...
       y[p-1] = next n bytes of signature

  3. compute the string Kc as follows
     Q = H(I || u32str(q) || u16str(D_MESG) || C || message)
     for ( i = 0; i < p; i = i + 1 ) {
       a = coef(Q || Cksm(Q), i, w)
       tmp = y[i]
       for ( j = a; j < 2^w - 1; j = j + 1 ) {
          tmp = H(I || u32str(q) || u16str(i) || u8str(j) || tmp)
       }
       z[i] = tmp
     }
     Kc = H(I || u32str(q) || u16str(D_PBLC) || z[0] || z[1] || ... || z[p-1])

  4. return Kc

5.  Leighton-Micali Signatures

   The Leighton-Micali Signature (LMS) method can sign a potentially
   large but fixed number of messages.  An LMS system uses two
   cryptographic components: a one-time signature method and a hash
   function.  Each LMS public/private key pair is associated with a
   perfect binary tree, each node of which contains an m-byte value,
   where m is the output length of the hash function.  Each leaf of the
   tree contains the value of the public key of an LM-OTS public/private
   key pair.  The value contained by the root of the tree is the LMS
   public key.  Each interior node is computed by applying the hash
   function to the concatenation of the values of its children nodes.

McGrew, et al.           Expires October 7, 2018               [Page 14]
Internet-Draft            Hash-Based Signatures               April 2018

   Each node of the tree is associated with a node number, an unsigned
   integer that is denoted as node_num in the algorithms below, which is
   computed as follows.  The root node has node number 1; for each node
   with node number N < 2^h, its left child has node number 2*N, while
   its right child has node number 2*N+1.  The result of this is that
   each node within the tree will have a unique node number, and the
   leaves will have node numbers 2^h, (2^h)+1, (2^h)+2, ...,
   (2^h)+(2^h)-1.  In general, the j-th node at level i has node number
   2^i + j.  The node number can conveniently be computed when it is
   needed in the LMS algorithms, as described in those algorithms.

5.1.  Parameters

   An LMS system has the following parameters:

      h : the height of the tree, and

      m : the number of bytes associated with each node.

      H : a second-preimage-resistant cryptographic hash function that
      accepts byte strings of any length, and returns an m-byte string.

   There are 2^h leaves in the tree.  The hash function used within the
   LMS system SHOULD be the same as the hash function used within the
   LM-OTS system used to generate the leaves.

                 +--------------------+--------+----+----+
                 | Name               | H      | m  | h  |
                 +--------------------+--------+----+----+
                 | LMS_SHA256_M32_H5  | SHA256 | 32 | 5  |
                 |                    |        |    |    |
                 | LMS_SHA256_M32_H10 | SHA256 | 32 | 10 |
                 |                    |        |    |    |
                 | LMS_SHA256_M32_H15 | SHA256 | 32 | 15 |
                 |                    |        |    |    |
                 | LMS_SHA256_M32_H20 | SHA256 | 32 | 20 |
                 |                    |        |    |    |
                 | LMS_SHA256_M32_H25 | SHA256 | 32 | 25 |
                 +--------------------+--------+----+----+

                                  Table 2

5.2.  LMS Private Key

   The format of the LMS private key is an internal matter to the
   implementation, and this document does not attempt to define it.  One
   possibility is that it may consist of an array OTS_PRIV[] of 2^h LM-
   OTS private keys, and the leaf number q of the next LM-OTS private

McGrew, et al.           Expires October 7, 2018               [Page 15]
Internet-Draft            Hash-Based Signatures               April 2018

   key that has not yet been used.  The q-th element of OTS_PRIV[] is
   generated using Algorithm 0 with the identifiers I, q.  The leaf
   number q is initialized to zero when the LMS private key is created.
   The process is as follows:

   Algorithm 5: Computing an LMS Private Key.

      1. determine h and m from the typecode and Table 2.

      2. set I to a uniformly random 16-byte string

      3. compute the array OTS_PRIV[] as follows:
         for ( q = 0; q < 2^h; q = q + 1) {
            OTS_PRIV[q] = LM-OTS private key with identifiers I, q
         }

      4. q = 0

   An LMS private key MAY be generated pseudorandomly from a secret
   value, in which case the secret value MUST be at least m bytes long,
   be uniformly random, and MUST NOT be used for any other purpose than
   the generation of the LMS private key.  The details of how this
   process is done do not affect interoperability; that is, the public
   key verification operation is independent of these details.
   Appendix A provides an example of a pseudorandom method for computing
   an LMS private key.

   The signature generation logic uses q as the next leaf to use, hence
   step 3 starts it off at the left-most one.

5.3.  LMS Public Key

   An LMS public key is defined as follows, where we denote the public
   key final hash value (namely, the K value computed in algorithm 1)
   associated with the i-th LM-OTS private key as OTS_PUB_HASH[i], with
   i ranging from 0 to (2^h)-1.  Each instance of an LMS public/private
   key pair is associated with a balanced binary tree, and the nodes of
   that tree are indexed from 1 to 2^(h+1)-1.  Each node is associated
   with an m-byte string, and the string for the r-th node is denoted as
   T[r] and is defined as

  T[r]=/ H(I||u32str(r)||u16str(D_LEAF)||OTS_PUB_HASH[r-2^h])   if r >= 2^h,
       \ H(I||u32str(r)||u16str(D_INTR)||T[2*r]||T[2*r+1]) otherwise.

   The LMS public key is the string

   u32str(type) || u32str(otstype) || I || T[1]

McGrew, et al.           Expires October 7, 2018               [Page 16]
Internet-Draft            Hash-Based Signatures               April 2018

   Section 7 specifies the format of the type variable.  The value
   otstype is the parameter set for the LM-OTS public/private keypairs
   used.  The value I is the private key identifier, and is the value
   used for all computations for the same LMS tree.  The value T[1] can
   be computed via recursive application of the above equation, or by
   any equivalent method.  An iterative procedure is outlined in
   Appendix C.

5.4.  LMS Signature

   An LMS signature consists of

      the number q of the leaf associated with the LM-OTS signature, as
      a four-byte unsigned integer in network byte order,

      an LM-OTS signature,

      a typecode indicating the particular LMS algorithm,

      an array of h m-byte values that is associated with the path
      through the tree from the leaf associated with the LM-OTS
      signature to the root.

   Symbolically, the signature can be represented as

       u32str(q) || lmots_signature || u32str(type) ||
                 path[0] || path[1] || path[2] || ... || path[h-1]

   Section 7 specifies the typecode and more formally defines the
   format.  The array for a tree with height h will have h values and
   contains the values of the siblings of (or adjacent to) the nodes on
   the path from the leaf to the root, where the sibling to node A is
   the other node which shares node A's parent.  In the signature, 0 is
   counted from the bottom level of the tree, and so path[0] is the bthe
   value of the node adjacent to leaf node q; path[1] is the second
   level node that is adjacent to leaf node q's parent, and so up the
   tree until we get to path[h-1], which is the value of the next-to-
   the-top level node that leaf node q does not reside in.

   Below is a simple example of the authentication path for h=3 and q=2.
   The leaf marked OTS is the one time signature which is used to sign
   the actual message.  The nodes on the path from the OTS public key to
   the root are marked with a (*), while the nodes that are used within
   the path array are marked with a (**).  The values in the path array
   are those nodes which are siblings of the nodes on the path; path[0]
   is the leaf(**) node that is adjacent to the OTS pubic key (which is
   the start of the path); path[1] is the T[4]** node which is the
   sibling of the second Node (T[5]*) on the path, and path[2] is the

McGrew, et al.           Expires October 7, 2018               [Page 17]
Internet-Draft            Hash-Based Signatures               April 2018

   the T[3]** node which is the sibling of the third Node* (T[2]*) on
   the path.

                                Root
                                 |
                 ---------------------------------
                 |                               |
               T[2](*)                        T[3](**)
                 |                               |
          ------------------            -----------------
          |                |            |               |
       T(4)**           T[5](*)        T[6]            T[7]
          |                |            |               |
      ---------       ----------     --------       ---------
      |       |       |        |     |      |       |       |
     leaf    leaf    OTS  leaf(**) leaf   leaf    leaf    leaf

   The idea behind this authentication path is that it allows us to
   validate the OTS hash with using h path array values and hash
   computations.  What the verifier does is recompute the hashes up the
   path; first, he hashes the given OTS and path[0] value, giving a
   tentative T[5]' value.  Then, he hashes his path[1] and tentative
   T[5]' value to get a tentative T[2]' value.  Then, he hashes that and
   the path[2] value to get a tentative Root' value.  If that value is
   the known public key of the Merkle tree, then we can assume that the
   value T[2]' he got was the correct T[2] value in the original tree,
   and so the T[5]' value he got wsa the correct T[5] value in the
   original tree, and so the OTS public key is the same as in the
   original, and hence is correct.

5.4.1.  LMS Signature Generation

   To compute the LMS signature of a message with an LMS private key,
   the signer first computes the LM-OTS signature of the message using
   the leaf number of the next unused LM-OTS private key.  The leaf
   number q in the signature is set to the leaf number of the LMS
   private key that was used in the signature.  Before releasing the
   signature, the leaf number q in the LMS private key MUST be
   incremented, to prevent the LM-OTS private key from being used again.
   If the LMS private key is maintained in nonvolatile memory, then the
   implementation MUST ensure that the incremented value has been stored
   before releasing the signature.  The issue this tries to prevent is a
   scenario where a) we generate a signature, using one LM-OTS private
   key, and release it to the application, b) before we update the
   nonvolatile memory, we crash, and c) we reboot, and generate a second
   signature using the same LM-OTS private key; with two different

McGrew, et al.           Expires October 7, 2018               [Page 18]
Internet-Draft            Hash-Based Signatures               April 2018

   signatures using the same LM-OTS private key, someone could
   potentially generate a forged signature of a third message.

   The array of node values in the signature MAY be computed in any way.
   There are many potential time/storage tradeoffs that can be applied.
   The fastest alternative is to store all of the nodes of the tree and
   set the array in the signature by copying them; pseudocode to do so
   appears in Appendix D.  The least storage intensive alternative is to
   recompute all of the nodes for each signature.  Note that the details
   of this procedure are not important for interoperability; it is not
   necessary to know any of these details in order to perform the
   signature verification operation.  The internal nodes of the tree
   need not be kept secret, and thus a node-caching scheme that stores
   only internal nodes can sidestep the need for strong protections.

   Several useful time/storage tradeoffs are described in the 'Small-
   Memory LM Schemes' section of [USPTO5432852].

5.4.2.  LMS Signature Verification

   An LMS signature is verified by first using the LM-OTS signature
   verification algorithm (Algorithm 4b) to compute the LM-OTS public
   key from the LM-OTS signature and the message.  The value of that
   public key is then assigned to the associated leaf of the LMS tree,
   then the root of the tree is computed from the leaf value and the
   array path[] as described in Algorithm 6 below.  If the root value
   matches the public key, then the signature is valid; otherwise, the
   signature fails.

McGrew, et al.           Expires October 7, 2018               [Page 19]
Internet-Draft            Hash-Based Signatures               April 2018

   Algorithm 6: LMS Signature Verification

    1. if the public key is not at least eight bytes long, return
       INVALID

    2. parse pubtype, I, and T[1] from the public key as follows:

       a. pubtype = strTou32(first 4 bytes of public key)

       b. ots_typecode = strTou32(next 4 bytes of public key)

       c. set m according to pubtype, based on Table 2

       d. if the public key is not exactly 24 + m bytes
          long, return INVALID

       e. I = next 16 bytes of the public key

       f. T[1] = next m bytes of the public key

    3. compute the LMS Public Key Candidate Tc from the signature,
       message, identifier, pubtype and ots_typecode using Algorithm 6a.

    4. if Tc is equal to T[1], return VALID; otherwise, return INVALID

   Algorithm 6a: Computing an LMS Public Key Candidate from a Signature,
   Message, Identifier, and algorithm typecode

  1. if the signature is not at least eight bytes long, return INVALID

  2. parse sigtype, q, lmots_signature, and path from the signature as
     follows:

    a. q = strTou32(first 4 bytes of signature)

    b. otssigtype = strTou32(next 4 bytes of signature)

    c. if otssigtype is not the OTS typecode from the public key, return INVALID

    d. set n, p according to otssigtype and Table 1; if the
    signature is not at least 12 + n * (p + 1) bytes long, return INVALID

    e. lmots_signature = bytes 4 through 8 + n * (p + 1) - 1 of signature

    f. sigtype = strTou32(4 bytes of signature at location 8 + n * (p + 1))

    f. if sigtype is not the LM typecode from the public key, return INVALID

McGrew, et al.           Expires October 7, 2018               [Page 20]
Internet-Draft            Hash-Based Signatures               April 2018

    g. set m, h according to sigtype and Table 2

    h. if q >= 2^h or the signature is not exactly 12 + n * (p + 1) + m * h bytes long, return INVALID

    i. set path as follows:
          path[0] = next m bytes of signature
          path[1] = next m bytes of signature
          ...
          path[h-1] = next m bytes of signature

  3. Kc = candidate public key computed by applying Algorithm 4b
     to the signature lmots_signature, the message, and the
     identifiers I, q

  4. compute the candidate LMS root value Tc as follows:
     node_num = 2^h + q
     tmp = H(I || u32str(node_num) || u16str(D_LEAF) || Kc)
     i = 0
     while (node_num > 1) {
       if (node_num is odd):
         tmp = H(I||u32str(node_num/2)||u16str(D_INTR)||path[i]||tmp)
       else:
         tmp = H(I||u32str(node_num/2)||u16str(D_INTR)||tmp||path[i])
       node_num = node_num/2
       i = i + 1
     }
     Tc = tmp

  5. return Tc

6.  Hierarchical signatures

   In scenarios where it is necessary to minimize the time taken by the
   public key generation process, a Hierarchical N-time Signature System
   (HSS) can be used.  This hierarchical scheme, which we describe in
   this section, uses an LMS scheme as a component.  HSS, in essence,
   utilizes a tree of LMS trees.  There is a single LMS tree at level 0
   (the root).  Each LMS tree at level i is used to sign 2^h objects
   (where h is the height of trees at level i).  If i < L-1, then each
   object will be another LMS tree at level i+1; if i = L-1, we've
   reached the bottom of the HSS tree, and so each object is an
   individual message.  The HSS public key contains the public key of
   the LMS tree at the root, and an HSS signature is associated with a
   path from the root of the HSS tree to the leaf.

   Compared to LMS, HSS has a much reduced public key generation time,
   as only the root tree needs to be generated prior to the distribution
   of the HSS public key.  For example, a L=3 tree with h=10 at each

McGrew, et al.           Expires October 7, 2018               [Page 21]
Internet-Draft            Hash-Based Signatures               April 2018

   level would have 1 level 0 LMS tree, 2^10 level 1 LMS trees and 2^20
   level 2 LMS trees.  Only 1024 OTS public keys need to be computed to
   generate the HSS public key (as you need to compute only the level 0
   LMS tree to compute that value; you can, of course, decide to compute
   the initial level 1 and level 2 LMS trees).  And, the 2^20 level 2
   LMS trees can jointly sign a total of over a billion messages.  In
   contrast, a single LMS tree that could sign a billion messages would
   require a billion OTS public keys to be computed first (even if h=30
   were allowed in a supported parameter set).

   Each level of the hierarchy is associated with a distinct LMS public
   key, private key, signature, and identifier.  The number of levels is
   denoted L, and is between one and eight, inclusive.  The following
   notation is used, where i is an integer between 0 and L-1 inclusive,
   and the root of the hierarchy is level 0:

      prv[i] is the LMS private key of the i-th level,

      pub[i] is the LMS public key of the i-th level (which includes the
      identifier I as well as the key value K),

      sig[i] is the LMS signature generated using the private key of the
      i-th level,

   In this section, we say that an N-time private key is exhausted when
   it has generated N signatures, and thus it can no longer be used for
   signing.

   HSS allows L=1, in which case the HSS public key and signature
   formats are essentially the LMS public key and signature formats,
   prepended by a fixed field.  Since HSS with L=1 has very little
   overhead compared to LMS, all implementations MUST support HSS in
   order to maximize interoperability.

6.1.  Key Generation

   When an HSS key pair is generated, the key pair for each level MUST
   have its own identifier I.

   To generate an HSS private and public key pair, new LMS private and
   public keys are generated for prv[i] and pub[i] for i=0, ... , L-1.
   These key pairs, and their identifiers, MUST be generated
   independently.

   The public key of the HSS scheme consists of the number of levels L,
   followed by pub[0], the public key of the top level.

McGrew, et al.           Expires October 7, 2018               [Page 22]
Internet-Draft            Hash-Based Signatures               April 2018

   The HSS private key consists of prv[0], ... , prv[L-1].  The values
   pub[0] does not change (and, except for the index q, the value of
   prv[0] need not change), though the values of pub[i] and prv[i] are
   dynamic for i > 0, and are changed by the signature generation
   algorithm.

   Here is some pseudocode that explains this key generation logic

   Algorithm 7: Generating an HSS keypair

     1. generate L LMS key pairs, as specified in sections 5.2 and 5.3

     2. sign each child key pair with the private key of its parent:
        i  = 0
        while (i < L-1) {
            sig[i] = lms_signature( pub[i+1], priv[i] )
            i = i + 1
        }

     3. return u32str(L) || pub[0]

   Note that the generation of the non-root LMS key pair, and the
   operations of step 2 can be delayed until the generation of the first
   signature, should it be advantageous for the implementation to do so.

6.2.  Signature Generation

   To sign a message using the private key prv, the following steps are
   performed:

      If prv[L-1] is exhausted, then determine the smallest integer d
      such that all of the private keys prv[d], prv[d+1], ... , prv[L-1]
      are exhausted.  If d is equal to zero, then the HSS key pair is
      exhausted, and it MUST NOT generate any more signatures.
      Otherwise, the key pairs for levels d through L-1 must be
      regenerated during the signature generation process, as follows.
      For i from d to L-1, a new LMS public and private key pair with a
      new identifier is generated, pub[i] and prv[i] are set to those
      values, then the public key pub[i] is signed with prv[i-1], and
      sig[i-1] is set to the resulting value.

      The message is signed with prv[L-1], and the value sig[L-1] is set
      to that result.

      The value of the HSS signature is set as follows.  We let
      signed_pub_key denote an array of octet strings, where
      signed_pub_key[i] = sig[i] || pub[i+1], for i between 0 and Nspk-

McGrew, et al.           Expires October 7, 2018               [Page 23]
Internet-Draft            Hash-Based Signatures               April 2018

      1, inclusive, where Nspk = L-1 denotes the number of signed public
      keys.  Then the HSS signature is u32str(Nspk) ||
      signed_pub_key[0] || ... || signed_pub_key[Nspk-1] || sig[Nspk].

      Note that the number of signed_pub_key elements in the signature
      is indicated by the value Nspk that appears in the initial four
      bytes of the signature.

   Here is some pseudocode of the above logic

   Algorithm 7a: Generating an HSS signature

  1. If the message-signing key prv[L-1] is exhausted, regenerate that
     key pair, togheter with any parent key paris that might be necessary.
     If the root key pair is exhausted, then the HSS key pair is exhausted
     and it MUST NOT generate any more signatures.

     d = L
     while (prv[d-1].q == 2^(prv[d-1].h)) {
         if (d == 0)
             return FAILURE
         d = d - 1
     }
     while (d < L) {
         create lms keypair pub[d], prv[d]
         sig[d-1] = lms_signature( pub[d], prv[d-1] )
         d = d + 1
     }

  2. sign the message
     sig[L-1] = lms_signature( msg, prv[L-1] )

  3. Create the list of signed public keys
     i = 0;
     while (i < L-1) {
         signed_pub_key[i] = sig[i] || pub[i+1]
         i = i + 1
     }

  4. return u32str(L-1) || signed_pub_key[0] || ... || signed_pub_key[L-2] || sig[L-1]

   In the specific case of L=1, the format of an HSS signature is

      u32str(0) || sig[0]

   In the general case, the format of an HSS signature is

McGrew, et al.           Expires October 7, 2018               [Page 24]
Internet-Draft            Hash-Based Signatures               April 2018

   u32str(Nspk) || signed_pub_key[0] || ... || signed_pub_key[Nspk-1] || sig[Nspk]

   which is equivalent to

   u32str(Nspk) || sig[0] || pub[1] || ... || sig[Nspk-1] || pub[Nspk] || sig[Nspk]

6.3.  Signature Verification

   To verify a signature sig and message using the public key pub, the
   following steps are performed:

      The signature S is parsed into its components as follows:

      Nspk = strTou32(first four bytes of S)
      if Nspk+1 is not equal to the number of levels L in pub:
         return INVALID
      for (i = 0; i < Nspk; i = i + 1) {
         siglist[i] = next LMS signature parsed from S
         publist[i] = next LMS public key parsed from S
      }
      siglist[Nspk] = next LMS signature parsed from S

      key = pub
      for (i = 0; i < Nspk; i = i + 1) {
         sig = siglist[i]
         msg = publist[i]
         if (lms_verify(msg, key, sig) != VALID):
             return INVALID
         key = msg
      return lms_verify(message, key, siglist[Nspk])

   Since the length of an LMS signature cannot be known without parsing
   it, the HSS signature verification algorithm makes use of an LMS
   signature parsing routine that takes as input a string consisting of
   an LMS signature with an arbitrary string appended to it, and returns
   both the LMS signature and the appended string.  The latter is passed
   on for further processing.

7.  Formats

   The signature and public key formats are formally defined using the
   External Data Representation (XDR) [RFC4506] in order to provide an
   unambiguous, machine readable definition.  For clarity, we also
   include a private key format as well, though consistency is not
   needed for interoperability and an implementation MAY use any private
   key format.  Though XDR is used, these formats are simple and easy to

McGrew, et al.           Expires October 7, 2018               [Page 25]
Internet-Draft            Hash-Based Signatures               April 2018

   parse without any special tools.  An illustration of the layout of
   data in these objects is provided below.  The definitions are as
   follows:

   /* one-time signatures */

   enum lmots_algorithm_type {
     lmots_reserved       = 0,
     lmots_sha256_n32_w1  = 1,
     lmots_sha256_n32_w2  = 2,
     lmots_sha256_n32_w4  = 3,
     lmots_sha256_n32_w8  = 4
   };

   typedef opaque bytestring32[32];

   struct lmots_signature_n32_p265 {
     bytestring32 C;
     bytestring32 y[265];
   };

   struct lmots_signature_n32_p133 {
     bytestring32 C;
     bytestring32 y[133];
   };

   struct lmots_signature_n32_p67 {
     bytestring32 C;
     bytestring32 y[67];
   };

   struct lmots_signature_n32_p34 {
     bytestring32 C;
     bytestring32 y[34];
   };

   union lmots_signature switch (lmots_algorithm_type type) {
    case lmots_sha256_n32_w1:
      lmots_signature_n32_p265 sig_n32_p265;
    case lmots_sha256_n32_w2:
      lmots_signature_n32_p133 sig_n32_p133;
    case lmots_sha256_n32_w4:
      lmots_signature_n32_p67  sig_n32_p67;
    case lmots_sha256_n32_w8:
      lmots_signature_n32_p34  sig_n32_p34;
    default:
      void;   /* error condition */

McGrew, et al.           Expires October 7, 2018               [Page 26]
Internet-Draft            Hash-Based Signatures               April 2018

   };

   /* hash based signatures (hbs) */

   enum lms_algorithm_type {
     lms_reserved       = 0,
     lms_sha256_n32_h5  = 5,
     lms_sha256_n32_h10 = 6,
     lms_sha256_n32_h15 = 7,
     lms_sha256_n32_h20 = 8,
     lms_sha256_n32_h25 = 9,
   };

   /* leighton-micali signatures (lms) */

   union lms_path switch (lms_algorithm_type type) {
    case lms_sha256_n32_h5:
      bytestring32 path_n32_h5[5];
    case lms_sha256_n32_h10:
      bytestring32 path_n32_h10[10];
    case lms_sha256_n32_h15:
      bytestring32 path_n32_h15[15];
    case lms_sha256_n32_h20:
      bytestring32 path_n32_h20[20];
    case lms_sha256_n32_h25:
      bytestring32 path_n32_h25[25];
    default:
      void;     /* error condition */
   };

   struct lms_signature {
     unsigned int q;
     lmots_signature lmots_sig;
     lms_path nodes;
   };

   struct lms_key_n32 {
     lmots_algorithm_type ots_alg_type;
     opaque I[16];
     opaque K[32];
   };

   union lms_public_key switch (lms_algorithm_type type) {
    case lms_sha256_n32_h5:
    case lms_sha256_n32_h10:
    case lms_sha256_n32_h15:
    case lms_sha256_n32_h20:

McGrew, et al.           Expires October 7, 2018               [Page 27]
Internet-Draft            Hash-Based Signatures               April 2018

    case lms_sha256_n32_h25:
         lms_key_n32 z_n32;
    default:
      void;     /* error condition */
   };

   /* hierarchical signature system (hss)  */

   struct hss_public_key {
     unsigned int L;
     lms_public_key pub;
   };

   struct signed_public_key {
     lms_signature sig;
     lms_public_key pub;
   }

   struct hss_signature {
     signed_public_key signed_keys<7>;
     lms_signature sig_of_message;
   };

8.  Rationale

   The goal of this note is to describe the LM-OTS, LMS and HSS
   algorithms following the original references and present the modern
   security analysis of those algorithms.  Other signature methods are
   out of scope and may be interesting follow-on work.

   We adopt the techniques described by Leighton and Micali to mitigate
   attacks that amortize their work over multiple invocations of the
   hash function.

   The values taken by the identifier I across different LMS public/
   private key pairs are chosen randomly in order to improve security.
   The analysis of this method in [Fluhrer17] shows that we do not need
   uniqueness to ensure security; we do need to ensure that we don't
   have a large number of private keys that use the same I value.  By
   randomly selecting 16 byte I values, the chance that, out of 2^64
   private keys, 4 or more of them will use the same I value is
   negligible (that is, has probability less than 2^-128).

   The reason this size was selected was to optimize the Winternitz hash
   chain operation.  With the current settings, the value being hashed
   is exactly 55 bytes long (for a 32 byte hash function), which SHA-256
   can hash in a single hash compression operation.  Other hash
   functions may be used in future specifications; all the ones that we

McGrew, et al.           Expires October 7, 2018               [Page 28]
Internet-Draft            Hash-Based Signatures               April 2018

   will be likely to support (SHA-512/256 and the various SHA-3 hashes)
   would work well with a 16-byte I value.

   The signature and public key formats are designed so that they are
   relatively easy to parse.  Each format starts with a 32-bit
   enumeration value that indicates the details of the signature
   algorithm and provides all of the information that is needed in order
   to parse the format.

   The Checksum Section 4.4 is calculated using a non-negative integer
   "sum", whose width was chosen to be an integer number of w-bit fields
   such that it is capable of holding the difference of the total
   possible number of applications of the function H as defined in the
   signing algorithm of Section 4.5 and the total actual number.  In the
   case that the number of times H is applied is 0, the sum is (2^w - 1)
   * (8*n/w).  Thus for the purposes of this document, which describes
   signature methods based on H = SHA256 (n = 32 bytes) and w = { 1, 2,
   4, 8 }, the sum variable is a 16-bit non-negative integer for all
   combinations of n and w.  The calculation uses the parameter ls
   defined in Section 4.1 and calculated in Appendix B, which indicates
   the number of bits used in the left-shift operation.

8.1.  Security string

   To improve security against attacks that amortize their effort
   against multiple invocations of the hash function, Leighton and
   Micali introduce a "security string" that is distinct for each
   invocation of that function.  Whenever this process computes a hash,
   the string being hashed will start with a string formed from the
   below fields.  These fields will appear in fixed locations in the
   value we compute the hash of, and so we list where in the hash these
   fields would be present.  These fields that make up this string are:

      I - a 16-byte identifier for the LMS public/private key pair.  It
      MUST be chosen uniformly at random, or via a pseudorandom process,
      at the time that a key pair is generated, in order to minimize the
      probability that any specific value of I be used for a large
      number of different LMS private keys.  This is always bytes 0-15
      of the value being hashed.

      r - in the LMS N-time signature scheme, the node number r
      associated with a particular node of a hash tree is used as an
      input to the hash used to compute that node.  This value is
      represented as a 32-bit (four byte) unsigned integer in network
      byte order.  Either r or q (depending on the domain separation
      parameter) will be bytes 16-19 of the value being hashed.

McGrew, et al.           Expires October 7, 2018               [Page 29]
Internet-Draft            Hash-Based Signatures               April 2018

      q - in the LMS N-time signature scheme, each LM-OTS signature is
      associated with the leaf of a hash tree, and q is set to the leaf
      number.  This ensures that a distinct value of q is used for each
      distinct LM-OTS public/private key pair.  This value is
      represented as a 32-bit (four byte) unsigned integer in network
      byte order.  Either r or q (depending on the domain separation
      parameter) will be bytes 16-19 of the value being hashed.

      D - a domain separation parameter, which is a two byte identifier
      that takes on different values in the different contexts in which
      the hash function is invoked.  D occurs in bytes 20, 21 of the the
      valeu being hashed, and takes on the following values:

         D_PBLC = 0x8080 when computing the hash of all of the iterates
         in the LM-OTS algorithm

         D_MESG = 0x8181 when computing the hash of the message in the
         LM-OTS algorithms

         D_LEAF = 0x8282 when computing the hash of the leaf of an LMS
         tree

         D_INTR = 0x8383 when computing the hash of an interior node of
         an LMS tree

         i - a value between 0 and 264; this is used in the LM-OTS
         scheme, when either computing the iterations of the Winternitz
         chain, or when using the suggested LM-OTS private key
         generation process.  It is represented as a 16-bit (two-byte)
         unsigned integer in network byte order.

      j - in the LM-OTS scheme, j is the iteration number used when the
      private key element is being iteratively hashed.  It is
      represented as an 8-bit (one byte) unsigned integer and is present
      if D is a value between 0 and 264.  If present, it occurs at byte
      22 of the value being hashed.

      C - an n-byte randomizer that is included with the message
      whenever it is being hashed to improve security.  C MUST be chosen
      uniformly at random, or via a pseudorandom process.  It is present
      if D=D_MESG, and it occurs at bytes 22 to 21+n of the value being
      hashed.

9.  History

   This is the eleventh version of this draft.  It has the following
   changes from previous versions:

McGrew, et al.           Expires October 7, 2018               [Page 30]
Internet-Draft            Hash-Based Signatures               April 2018

   Version 10

      Numerous clarifications and typo corrections.

   Version 09

      Corrected size of the OTS signature in section 4.2

      Miscellaneous clarifications and typo corrections.

   Version 08

      Added additional test vector with private key

      Added appendix with discussion of parameter set trade-offs

      Miscellaneous clarifications and typo corrections.

   Version 07

      Corrected the LMS public key format specification in section 5.3;
      the format listed in section 7 was correct.

      Corrected the LMS public key generation algorithm in appendix C.
      The hashes listed in section 5.3 were correct.

      Corrected the HSS signature verification algorithm in section 6.3.

      Miscellaneous clarifications and typo corrections.

   Version 06

      Modified the order of the values that were hashed to make it
      easier to prove security.

      Decreased the size of the I LMS public key identifier to 16 bytes.

   Version 05

      Clarified the L=1 specific case.

      Extended the parameter sets to include an H=25 option

      A large number of corrections and clarifications

      Added a comparison to XMSS and SPHINCS, and citations to those
      algorithms and to the recent Security Standardization Research

McGrew, et al.           Expires October 7, 2018               [Page 31]
Internet-Draft            Hash-Based Signatures               April 2018

      2016 publications on the security of LMS and on the state
      management in hash-based signatures.

   Version 04

      Specified that, in the HSS method, the I value was computed from
      the I value of the parent LM tree.  Previous versions had the I
      value extracted from the public key (which meant that all LM trees
      of a particular level and public key used the same I value)

      Changed the length of the I field based on the parameter set.  As
      noted in the Rationale section, this allows an implementation to
      compute SHA256 n=32 based parameter sets significantly faster.

      Modified the XDR of an HSS signature not to use an array of LM
      signatures; LM signatures are variable length, and XDR doesn't
      support arrays of variable length structures.

      Changed the LMS registry to be in a consistent order with the LM-
      OTS parameter sets.  Also, added LMS parameter sets with height 15
      trees

   Previous versions

      In Algorithms 3 and 4, the message was moved from the initial
      position of the input to the function H to the final position, in
      the computation of the intermediate variable Q.  This was done to
      improve security by preventing an attacker that can find a
      collision in H from taking advantage of that fact via the forward
      chaining property of Merkle-Damgard.

      The Hierarchical Signature Scheme was generalized slightly so that
      it can use more than two levels.

      Several points of confusion were corrected; these had resulted
      from incomplete or inconsistent changes from the Merkle approach
      of the earlier draft to the Leighton-Micali approach.

   This section is to be removed by the RFC editor upon publication.

10.  IANA Considerations

   The Internet Assigned Numbers Authority (IANA) is requested to create
   two registries: one for OTS signatures, which includes all of the LM-
   OTS signatures as defined in Section 3, and one for Leighton-Micali
   Signatures, as defined in Section 4.  Additions to these registries
   require that a specification be documented in an RFC or another
   permanent and readily available reference in sufficient detail that

McGrew, et al.           Expires October 7, 2018               [Page 32]
Internet-Draft            Hash-Based Signatures               April 2018

   interoperability between independent implementations is possible.
   Each entry in the registry contains the following elements:

      a short name, such as "LMS_SHA256_M32_H10",

      a positive number, and

      a reference to a specification that completely defines the
      signature method test cases that can be used to verify the
      correctness of an implementation.

   Requests to add an entry to the registry MUST include the name and
   the reference.  The number is assigned by IANA.  Submitters SHOULD
   have their requests reviewed by the IRTF Crypto Forum Research Group
   (CFRG) at cfrg@ietf.org.  Interested applicants that are unfamiliar
   with IANA processes should visit http://www.iana.org.

   The numbers between 0xDDDDDDDD (decimal 3,722,304,989) and 0xFFFFFFFF
   (decimal 4,294,967,295) inclusive, will not be assigned by IANA, and
   are reserved for private use; no attempt will be made to prevent
   multiple sites from using the same value in different (and
   incompatible) ways [RFC2434].

   The LM-OTS registry is as follows.

         +----------------------+-----------+--------------------+
         | Name                 | Reference | Numeric Identifier |
         +----------------------+-----------+--------------------+
         | LMOTS_SHA256_N32_W1  | Section 4 |     0x00000001     |
         |                      |           |                    |
         | LMOTS_SHA256_N32_W2  | Section 4 |     0x00000002     |
         |                      |           |                    |
         | LMOTS_SHA256_N32_W4  | Section 4 |     0x00000003     |
         |                      |           |                    |
         | LMOTS_SHA256_N32_W8  | Section 4 |     0x00000004     |
         +----------------------+-----------+--------------------+

                                  Table 3

   The LMS registry is as follows.

McGrew, et al.           Expires October 7, 2018               [Page 33]
Internet-Draft            Hash-Based Signatures               April 2018

          +--------------------+-----------+--------------------+
          | Name               | Reference | Numeric Identifier |
          +--------------------+-----------+--------------------+
          | LMS_SHA256_M32_H5  | Section 5 |     0x00000005     |
          |                    |           |                    |
          | LMS_SHA256_M32_H10 | Section 5 |     0x00000006     |
          |                    |           |                    |
          | LMS_SHA256_M32_H15 | Section 5 |     0x00000007     |
          |                    |           |                    |
          | LMS_SHA256_M32_H20 | Section 5 |     0x00000008     |
          |                    |           |                    |
          | LMS_SHA256_M32_H25 | Section 5 |     0x00000009     |
          +--------------------+-----------+--------------------+

                                  Table 4

   An IANA registration of a signature system does not constitute an
   endorsement of that system or its security.

11.  Intellectual Property

   This draft is based on U.S. patent 5,432,852, which issued over
   twenty years ago and is thus expired.

11.1.  Disclaimer

   This document is not intended as legal advice.  Readers are advised
   to consult with their own legal advisers if they would like a legal
   interpretation of their rights.

   The IETF policies and processes regarding intellectual property and
   patents are outlined in [RFC3979] and [RFC4879] and at
   https://datatracker.ietf.org/ipr/about.

12.  Security Considerations

   The hash function H MUST have second preimage resistance: it must be
   computationally infeasible for an attacker that is given one message
   M to be able to find a second message M' such that H(M) = H(M').

   The security goal of a signature system is to prevent forgeries.  A
   successful forgery occurs when an attacker who does not know the
   private key associated with a public key can find a message (distinct
   from all previously signed ones) and signature that is valid with
   that public key (that is, the Signature Verification algorithm
   applied to that signature and message and public key will return
   VALID).  Such an attacker, in the strongest case, may have the

McGrew, et al.           Expires October 7, 2018               [Page 34]
Internet-Draft            Hash-Based Signatures               April 2018

   ability to forge valid signatures for an arbitrary number of other
   messages.

   LMS is provably secure in the random oracle model, where the hash
   compression function is considered the random oracle, as shown by
   [Fluhrer17].  Corollary 1 of that paper states:

      If we have no more than 2^64 randomly chosen LMS private keys,
      allow the attacker access to a signing oracle and a SHA-256 hash
      compression oracle, and allow a maximum of 2^120 hash compression
      computations, then the probability of an attacker being able to
      generate a single forgery against any of those LMS keys is less
      than 2^-129.

   Many of the objects within the public key and the signature start
   with a typecode.  A verifier MUST check each of these typecodes, and
   a verification operation on a signature with an unknown type, or a
   type that does not correspond to the type within the public key MUST
   return INVALID.  The expected length of a variable-length object can
   be determined from its typecode, and if an object has a different
   length, then any signature computed from the object is INVALID.

12.1.  Hash Formats

   The format of the inputs to the hash function H have the property
   that each invocation of that function has an input that is repeated
   by a small bounded number of other inputs (due to potential repeats
   of the I value), and in particular, will vary somewhere in the first
   23 bytes of the value being hashed.  This property is important for a
   proof of security in the random oracle model.

   The formats used during key generation and signing

      I || u32str(q) || u16str(i) || u8str(j) || tmp
      I || u32str(q) || u16str(D_PBLC) || y[0] || ... || y[p-1]
      I || u32str(q) || u16str(D_MESG) || C || message
      I || u32str(r) || u16str(D_LEAF) || OTS_PUB_HASH[r-2^h]
      I || u32str(r) || u16str(D_INTR) || T[2*r] || T[2*r+1]
      I || u32str(q) || u16str(j) || u8str(0xff) || SEED

   Each hash type listed is distinct; at locations 20, 21 of each hash,
   there exists either a fixed value D_PBLC, D_MESG, D_LEAF, D_INTR, or
   a 16 bit value (i or j).  These fixed values are distinct from each
   other, and are large (over 32768), while the 16 bit values are small
   (currently no more than 265; possibly being slightly larger if larger
   hash functions are supported); hence the hash invocations with i/j
   will not collide any of the D_PBLC, D_MESG, D_LEAF, D_INTR hashes.
   The only other collision possibility is the Winternitz chain hash

McGrew, et al.           Expires October 7, 2018               [Page 35]
Internet-Draft            Hash-Based Signatures               April 2018

   colliding with the recommended pseudorandom key generation process;
   here, at location 22, the Winternitz chain function has the value
   u8str(j), where j is a value between 0 and 254, while location 22 of
   the recommended pseudorandom key generation process has value 255.

   For the Winternitz chaining function, D_PBLC, and D_MESG, the value
   of I || u32str(q) is distinct for each LMS leaf (or equivalently, for
   each q value).  For the Winternitz chaining function, the value of
   u16str(i) || u8str(j) is distinct for each invocation of H for a
   given leaf.  For D_PBLC and D_MESG, the input format is used only
   once for each value of q, and thus distinctness is assured.  The
   formats for D_INTR and D_LEAF are used exactly once for each value of
   r, which ensures their distinctness.  For the recommended
   pseudorandom key generation process, for a given value of I, q and j
   are distinct for each invocation of H.

   The value of I is chosen uniformly at random from the set of all 128
   bit strings.  If 2^64 public keys are generated (and hence 2^64
   random I values), there is a nontrivial probability of a duplicate
   (which would imply duplicate prefixes.  However, there will be an
   extremely high probability there will not be a four-way collision
   (that is, any I value used for four distinct LMS keys; probability <
   2^-132), and hence the number of repeats for any specific prefix will
   be limited to 3.  This is shown (in [Fluhrer17]) to have only a
   limited effect on the security of the system.

12.2.  Stateful signature algorithm

   The LMS signature system, like all N-time signature systems, requires
   that the signer maintain state across different invocations of the
   signing algorithm, to ensure that none of the component one-time
   signature systems are used more than once.  This section calls out
   some important practical considerations around this statefulness.

   In a typical computing environment, a private key will be stored in
   non-volatile media such as on a hard drive.  Before it is used to
   sign a message, it will be read into an application's Random Access
   Memory (RAM).  After a signature is generated, the value of the
   private key will need to be updated by writing the new value of the
   private key into non-volatile storage.  It is essential for security
   that the application ensure that this value is actually written into
   that storage, yet there may be one or more memory caches between it
   and the application.  Memory caching is commonly done in the file
   system, and in a physical memory unit on the hard disk that is
   dedicated to that purpose.  To ensure that the updated value is
   written to physical media, the application may need to take several
   special steps.  In a POSIX environment, for instance, the O_SYNC flag
   (for the open() system call) will cause invocations of the write()

McGrew, et al.           Expires October 7, 2018               [Page 36]
Internet-Draft            Hash-Based Signatures               April 2018

   system call to block the calling process until the data has been
   written to the underlying hardware.  However, if that hardware has
   its own memory cache, it must be separately dealt with using an
   operating system or device specific tool such as hdparm to flush the
   on-drive cache, or turn off write caching for that drive.  Because
   these details vary across different operating systems and devices,
   this note does not attempt to provide complete guidance; instead, we
   call the implementer's attention to these issues.

   When hierarchical signatures are used, an easy way to minimize the
   private key synchronization issues is to have the private key for the
   second level resident in RAM only, and never write that value into
   non-volatile memory.  A new second level public/private key pair will
   be generated whenever the application (re)starts; thus, failures such
   as a power outage or application crash are automatically
   accommodated.  Implementations SHOULD use this approach wherever
   possible.

12.3.  Security of LM-OTS Checksum

   To show the security of LM-OTS checksum, we consider the signature y
   of a message with a private key x and let h = H(message) and
   c = Cksm(H(message)) (see Section 4.5).  To attempt a forgery, an
   attacker may try to change the values of h and c.  Let h' and c'
   denote the values used in the forgery attempt.  If for some integer j
   in the range 0 to u, where u = ceil(8*n/w) is the size of the range
   that the checksum value can cover), inclusive,

      a' = coef(h', j, w),

      a = coef(h, j, w), and

      a' > a

   then the attacker can compute F^a'(x[j]) from F^a(x[j]) = y[j] by
   iteratively applying function F to the j-th term of the signature an
   additional (a' - a) times.  However, as a result of the increased
   number of hashing iterations, the checksum value c' will decrease
   from its original value of c.  Thus a valid signature's checksum will
   have, for some number k in the range u to (p-1), inclusive,

      b' = coef(c', k, w),

      b = coef(c, k, w), and

      b' < b

McGrew, et al.           Expires October 7, 2018               [Page 37]
Internet-Draft            Hash-Based Signatures               April 2018

   Due to the one-way property of F, the attacker cannot easily compute
   F^b'(x[k]) from F^b(x[k]) = y[k].

13.  Comparison with other work

   The eXtended Merkle Signature Scheme (XMSS) [XMSS] is similar to HSS
   in several ways.  Both are stateful hash based signature schemes, and
   both use a hierarchical approach, with a Merkle tree at each level of
   the hierarchy.  XMSS signatures are slightly shorter than HSS
   signatures, for equivalent security and an equal number of
   signatures.

   HSS has several advantages over XMSS.  HSS operations are roughly
   four times faster than the comparable XMSS ones, when SHA256 is used
   as the underlying hash.  This occurs because the hash operation done
   as a part of the Winternitz iterations dominates performance, and
   XMSS performs four compression function invocations (two for the PRF,
   two for the F function) where HSS needs only perform one.
   Additionally, HSS is somewhat simpler (as each hash invocation is
   just a prefix followed by the data being hashed).

14.  Acknowledgements

   Thanks are due to Chirag Shroff, Andreas Huelsing, Burt Kaliski, Eric
   Osterweil, Ahmed Kosba, Russ Housley, Philip Lafrance, Alexander
   Truskovsky, Mark Peruzel for constructive suggestions and valuable
   detailed review.  We especially acknowledge Jerry Solinas, Laurie
   Law, and Kevin Igoe, who pointed out the security benefits of the
   approach of Leighton and Micali [USPTO5432852] and Jonathan Katz, who
   gave us security guidance, and Bruno Couillard and Jim Goodman for an
   especially thorough review.

15.  References

15.1.  Normative References

   [FIPS180]  National Institute of Standards and Technology, "Secure
              Hash Standard (SHS)", FIPS 180-4, March 2012.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC2434]  Narten, T. and H. Alvestrand, "Guidelines for Writing an
              IANA Considerations Section in RFCs", RFC 2434,
              DOI 10.17487/RFC2434, October 1998,
              <https://www.rfc-editor.org/info/rfc2434>.

McGrew, et al.           Expires October 7, 2018               [Page 38]
Internet-Draft            Hash-Based Signatures               April 2018

   [RFC3979]  Bradner, S., Ed., "Intellectual Property Rights in IETF
              Technology", RFC 3979, DOI 10.17487/RFC3979, March 2005,
              <https://www.rfc-editor.org/info/rfc3979>.

   [RFC4506]  Eisler, M., Ed., "XDR: External Data Representation
              Standard", STD 67, RFC 4506, DOI 10.17487/RFC4506, May
              2006, <https://www.rfc-editor.org/info/rfc4506>.

   [RFC4879]  Narten, T., "Clarification of the Third Party Disclosure
              Procedure in RFC 3979", RFC 4879, DOI 10.17487/RFC4879,
              April 2007, <https://www.rfc-editor.org/info/rfc4879>.

   [USPTO5432852]
              Leighton, T. and S. Micali, "Large provably fast and
              secure digital signature schemes from secure hash
              functions", U.S. Patent 5,432,852, July 1995.

15.2.  Informative References

   [C:Merkle87]
              Merkle, R., "A Digital Signature Based on a Conventional
              Encryption Function", Lecture Notes in Computer
              Science crypto87vol, 1988.

   [C:Merkle89a]
              Merkle, R., "A Certified Digital Signature", Lecture Notes
              in Computer Science crypto89vol, 1990.

   [C:Merkle89b]
              Merkle, R., "One Way Hash Functions and DES", Lecture
              Notes in Computer Science crypto89vol, 1990.

   [Fluhrer17]
              Fluhrer, S., "Further analysis of a proposed hash-based
              signature standard",
              EPrint http://eprint.iacr.org/2017/553.pdf, 2017.

   [Grover96]
              Grover, L., "A fast quantum mechanical algorithm for
              database search", 28th ACM Symposium on the Theory of
              Computing p. 212, 1996.

   [Katz16]   Katz, J., "Analysis of a proposed hash-based signature
              standard", Security Standardization Research (SSR)
              Conference
              http://www.cs.umd.edu/~jkatz/papers/HashBasedSigs-
              SSR16.pdf, 2016.

McGrew, et al.           Expires October 7, 2018               [Page 39]
Internet-Draft            Hash-Based Signatures               April 2018

   [Merkle79]
              Merkle, R., "Secrecy, Authentication, and Public Key
              Systems", Stanford University Information Systems
              Laboratory Technical Report 1979-1, 1979.

   [STMGMT]   McGrew, D., Fluhrer, S., Kampanakis, P., Gazdag, S.,
              Butin, D., and J. Buchmann, "State Management for Hash-
              based Signatures.", Security Standardization Resarch (SSR)
              Conference 224., 2016.

   [XMSS]     Buchmann, J., Dahmen, E., and Andreas Huelsing, "XMSS-a
              practical forward secure signature scheme based on minimal
              security assumptions.", International Workshop on Post-
              Quantum Cryptography Springer Berlin., 2011.

Appendix A.  Pseudorandom Key Generation

   An implementation MAY use the following pseudorandom process for
   generating an LMS private key.

      SEED is an m-byte value that is generated uniformly at random at
      the start of the process,

      I is LMS key pair identifier,

      q denotes the LMS leaf number of an LM-OTS private key,

      x_q denotes the x array of private elements in the LM-OTS private
      key with leaf number q,

      j is an index of the private key element, and

      H is the hash function used in LM-OTS.

   The elements of the LM-OTS private keys are computed as:

   x_q[j] = H(I || u32str(q) || u16str(j) || u8str(0xff) || SEED).

   This process stretches the m-byte random value SEED into a (much
   larger) set of pseudorandom values, using a unique counter in each
   invocation of H.  The format of the inputs to H are chosen so that
   they are distinct from all other uses of H in LMS and LM-OTS.  A
   careful reader will note that this is similar to the hash we perform
   when iterating through the Winternitz chain; however in that chain,
   the iteration index will vary between 0 and 254 maximum (for W=8),
   while the corresponding value in this formula is 255.  This algorithm
   is included in the proof of security in [Fluhrer17] and hence this
   method is safe when used within the LMS system; however any other

McGrew, et al.           Expires October 7, 2018               [Page 40]
Internet-Draft            Hash-Based Signatures               April 2018

   cryptographical secure method of generating private keys would also
   be safe.

Appendix B.  LM-OTS Parameter Options

   The LM-OTS one time signature method uses several internal
   parameters, which are a function of the selected parameter set.
   These internal parameters set:

      p - This is the number of independent Winternitz chains used in
      the signature; it will be the number of w-bit digits needed to
      hold the n-bit hash (u in the below equations), along with the
      number of digits needed to hold the checksum (v in the below
      equations)

      ls - This is the size of the shift needed to move the checksum so
      that it appears in the checksum digits

   The parameters ls, and p are computed as follows:

     u = ceil(8*n/w)
     v = ceil((floor(lg((2^w - 1) * u)) + 1) / w)
     ls = 16 - (v * w)
     p = u + v

   Here u and v represent the number of w-bit fields required to contain
   the hash of the message and the checksum byte strings, respectively.
   And as the value of p is the number of w-bit elements of
   ( H(message) || Cksm(H(message)) ), it is also equivalently the
   number of byte strings that form the private key and the number of
   byte strings in the signature.  The value 16 in the ls computation of
   ls corresponds to the 16 bits value used for the sum variable in
   Algorithm 2 in Section 4.4

   A table illustrating various combinations of n and w with the
   associated values of u, v, ls, and p is provided in Table 5.

McGrew, et al.           Expires October 7, 2018               [Page 41]
Internet-Draft            Hash-Based Signatures               April 2018

   +---------+------------+-----------+-----------+-------+------------+
   |   Hash  | Winternitz |   w-bit   |   w-bit   |  Left |   Total    |
   |  Length | Parameter  |  Elements |  Elements | Shift | Number of  |
   |    in   |    (w)     |  in Hash  |     in    |  (ls) |   w-bit    |
   |  Bytes  |            |    (u)    |  Checksum |       |  Elements  |
   |   (n)   |            |           |    (v)    |       |    (p)     |
   +---------+------------+-----------+-----------+-------+------------+
   |    32   |     1      |    256    |     9     |   7   |    265     |
   |         |            |           |           |       |            |
   |    32   |     2      |    128    |     5     |   6   |    133     |
   |         |            |           |           |       |            |
   |    32   |     4      |     64    |     3     |   4   |     67     |
   |         |            |           |           |       |            |
   |    32   |     8      |     32    |     2     |   0   |     34     |
   +---------+------------+-----------+-----------+-------+------------+

                                  Table 5

Appendix C.  An iterative algorithm for computing an LMS public key

   The LMS public key can be computed using the following algorithm or
   any equivalent method.  The algorithm uses a stack of hashes for
   data.  It also makes use of a hash function with the typical
   init/update/final interface to hash functions; the result of the
   invocations hash_init(), hash_update(N[1]), hash_update(N[2]), ... ,
   hash_update(N[n]), v = hash_final(), in that order, is identical to
   that of the invocation of H(N[1] || N[2] || ... || N[n]).

McGrew, et al.           Expires October 7, 2018               [Page 42]
Internet-Draft            Hash-Based Signatures               April 2018

   Generating an LMS Public Key from an LMS Private Key

     for ( i = 0; i < 2^h; i = i + 1 ) {
       r = i + num_lmots_keys;
       temp = H(I || u32str(r) || u16str(D_LEAF) || OTS_PUB_HASH[i])
       j = i;
       while (j % 2 == 1) {
         r = (r - 1)/2;
         j = (j-1) / 2;
         left_side = pop(data stack);
         temp = H(I || u32str(r) || u16str(D_INTR) || left_side || temp)
       }
       push temp onto the data stack
    }
    public_key = pop(data stack)

   Note that this pseudocode expects that all 2^h leaves of the tree
   have equal depth; that is, num_lmots_keys to be a power of 2.  The
   maximum depth of the stack will be h-1 elements, that is, a total of
   (h-1)*n bytes; for the currently defined parameter sets, this will
   never be more than 768 bytes of data.

Appendix D.  Method for deriving authentication path for a signature

   The LMS signature consists of u32str(q) || lmots_signature ||
   u32str(type) || path[0] || path[1] || ... || path[h-1].  This
   appendix shows one method of constructing this signature, assuming
   that the implementation has stored the T[] array that was used to
   construct the public key.  Note that this is not the only possible
   method; other methods exist which don't assume that you have the
   entire T[] array in memory.  To construct a signature, you perform
   the following algorithm:

McGrew, et al.           Expires October 7, 2018               [Page 43]
Internet-Draft            Hash-Based Signatures               April 2018

   Generating an LMS Signature

  1. set type to the typecode of the LMS algorithm

  2. extract h from the typecode according to table 2

  3. create the LM-OTS signature for the message:
     ots_signature = lmots_sign(message, LMS_PRIV[q])

  4. compute the array path as follows:
     i = 0
     r = 2^h + q
     while (i < h) {
         temp = (r / 2^i) xor 1
         path[i] = T[temp]
         i = i + 1
    }

  5. S = u32str(q) || ots_signature || u32str(type) || path[0] || path[1] || ... || path[h-1]

  6. q = q + 1

  7. return S

   where 'xor' is the bitwise exclusive-or operation, and / is integer
   division (that is, rounded down to an integer value)

Appendix E.  Example Implementation

   An example implementation can be found online at
   http://github.com/cisco/hash-sigs.

Appendix F.  Parameter Set Recommendations

   As for guidance as to the number of LMS level, and the size of each,
   any discussion of performance is implementation specific.  In
   general, the sole drawback for a single LMS tree is the time it takes
   to generate the public key; as every LM-OTS public key needs to be
   generated, the time this takes can be substantial.  For a two level
   tree, only the top level LMS tree and the initial bottom level LMS
   tree needs to be generated initially (before the first signature is
   generated); this will in general be significantly quicker.

   To give a general idea on the trade-offs available, we include some
   measurements taken with the github.com/cisco/hash-sigs LMS
   implementation, taken on a 3.3 GHz Xeon processor, with threading
   enabled.  We tried various parameter sets, all with W=8 (which
   minimizes signature size, while increasing time).  These are here to

McGrew, et al.           Expires October 7, 2018               [Page 44]
Internet-Draft            Hash-Based Signatures               April 2018

   give a guideline as to what's possible; for the computational time,
   your mileage may vary, depending on the computing resources you have.
   The machine I have does not have the SHA-256 extensions; you could
   possibly do significantly better.

       ParmSet  KeyGenTime  SigSize   KeyLifetime
        15         6 sec      1616     30 seconds
        20         3 min      1776     16 minutes
        25      1.5 hour      1936     9 hours
       15/10       6 sec      3172     9 hours
       15/15       6 sec      3332     12 days
       20/10       3 min      3332     12 days
       20/15       3 min      3492     1 year
       25/10    1.5 hour      3492     1 year
       25/15    1.5 hour      3652     34 years

   ParmSet: this is the height of the Merkle tree(s); parameter sets
   listed as a single integer consists of a single Merkle tree of that
   height; parameter sets that consist of two trees are listed as x/y,
   with x being the height of the top level Merkle tree, and y being the
   bottom level.

   KeyGenTime: the measured key generation time; that is, the time
   needed to generate the public private key pair.

   SigSize: the size of a signature (in bytes)

   KeyLifetime: the lifetime of a key, assuming we generated 1000
   signatures per second.  In practice, we're not likely to get anywhere
   close to 1000 signatures per second sustained; if you have a more
   appropriate figure for your scenario, this column is pretty easy to
   recompute.

   As for signature generation or verification times, those are
   moderately insensitive to the above parameter settings (except for
   the Winternitz setting, and the number of Merkle trees for
   verification).  Tests on the same machine (without multithreading)
   gave approximately 4msec to sign a short message, 2.6msec to verify;
   these tests used a two level ParmSet; a single level would
   approximately halve the verification time.  All times can be
   significantly improved (by maybe a factor of 8) by using a parameter
   set with W=4; however that also about doubles the signature size.

Appendix G.  Test Cases

   This section provides test cases that can be used to verify or debug
   an implementation.  This data is formatted with the name of the
   elements on the left, and the value of the elements on the right, in

McGrew, et al.           Expires October 7, 2018               [Page 45]
Internet-Draft            Hash-Based Signatures               April 2018

   hexadecimal.  The concatenation of all of the values within a public
   key or signature produces that public key or signature, and values
   that do not fit within a single line are listed across successive
   lines.

   Test Case 1 Public Key

   --------------------------------------------
   HSS public key
   levels      00000002
   --------------------------------------------
   LMS type    00000005                         # LM_SHA256_M32_H5
   LMOTS type  00000004                         # LMOTS_SHA256_N32_W8
   I           61a5d57d37f5e46bfb7520806b07a1b8
   K           50650e3b31fe4a773ea29a07f09cf2ea
               30e579f0df58ef8e298da0434cb2b878
   --------------------------------------------
   --------------------------------------------

   Test Case 1 Message

   --------------------------------------------
   Message     54686520706f77657273206e6f742064  |The powers not d|
               656c65676174656420746f2074686520  |elegated to the |
               556e6974656420537461746573206279  |United States by|
               2074686520436f6e737469747574696f  | the Constitutio|
               6e2c206e6f722070726f686962697465  |n, nor prohibite|
               6420627920697420746f207468652053  |d by it to the S|
               74617465732c20617265207265736572  |tates, are reser|
               76656420746f20746865205374617465  |ved to the State|
               7320726573706563746976656c792c20  |s respectively, |
               6f7220746f207468652070656f706c65  |or to the people|
               2e0a                              |..|
   --------------------------------------------

   Test Case 1 Signature

   --------------------------------------------
   HSS signature
   Nspk        00000001
   sig[0]:
   --------------------------------------------
   LMS signature
   q           00000005
   --------------------------------------------
   LMOTS signature
   LMOTS type  00000004                         # LMOTS_SHA256_N32_W8
   C           d32b56671d7eb98833c49b433c272586

McGrew, et al.           Expires October 7, 2018               [Page 46]
Internet-Draft            Hash-Based Signatures               April 2018

               bc4a1c8a8970528ffa04b966f9426eb9
   y[0]        965a25bfd37f196b9073f3d4a232feb6
               9128ec45146f86292f9dff9610a7bf95
   y[1]        a64c7f60f6261a62043f86c70324b770
               7f5b4a8a6e19c114c7be866d488778a0
   y[2]        e05fd5c6509a6e61d559cf1a77a970de
               927d60c70d3de31a7fa0100994e162a2
   y[3]        582e8ff1b10cd99d4e8e413ef469559f
               7d7ed12c838342f9b9c96b83a4943d16
   y[4]        81d84b15357ff48ca579f19f5e71f184
               66f2bbef4bf660c2518eb20de2f66e3b
   y[5]        14784269d7d876f5d35d3fbfc7039a46
               2c716bb9f6891a7f41ad133e9e1f6d95
   y[6]        60b960e7777c52f060492f2d7c660e14
               71e07e72655562035abc9a701b473ecb
   y[7]        c3943c6b9c4f2405a3cb8bf8a691ca51
               d3f6ad2f428bab6f3a30f55dd9625563
   y[8]        f0a75ee390e385e3ae0b906961ecf41a
               e073a0590c2eb6204f44831c26dd768c
   y[9]        35b167b28ce8dc988a3748255230cef9
               9ebf14e730632f27414489808afab1d1
   y[10]       e783ed04516de012498682212b078105
               79b250365941bcc98142da13609e9768
   y[11]       aaf65de7620dabec29eb82a17fde35af
               15ad238c73f81bdb8dec2fc0e7f93270
   y[12]       1099762b37f43c4a3c20010a3d72e2f6
               06be108d310e639f09ce7286800d9ef8
   y[13]       a1a40281cc5a7ea98d2adc7c7400c2fe
               5a101552df4e3cccfd0cbf2ddf5dc677
   y[14]       9cbbc68fee0c3efe4ec22b83a2caa3e4
               8e0809a0a750b73ccdcf3c79e6580c15
   y[15]       4f8a58f7f24335eec5c5eb5e0cf01dcf
               4439424095fceb077f66ded5bec73b27
   y[16]       c5b9f64a2a9af2f07c05e99e5cf80f00
               252e39db32f6c19674f190c9fbc506d8
   y[17]       26857713afd2ca6bb85cd8c107347552
               f30575a5417816ab4db3f603f2df56fb
   y[18]       c413e7d0acd8bdd81352b2471fc1bc4f
               1ef296fea1220403466b1afe78b94f7e
   y[19]       cf7cc62fb92be14f18c2192384ebceaf
               8801afdf947f698ce9c6ceb696ed70e9
   y[20]       e87b0144417e8d7baf25eb5f70f09f01
               6fc925b4db048ab8d8cb2a661ce3b57a
   y[21]       da67571f5dd546fc22cb1f97e0ebd1a6
               5926b1234fd04f171cf469c76b884cf3
   y[22]       115cce6f792cc84e36da58960c5f1d76
               0f32c12faef477e94c92eb75625b6a37
   y[23]       1efc72d60ca5e908b3a7dd69fef02491

McGrew, et al.           Expires October 7, 2018               [Page 47]
Internet-Draft            Hash-Based Signatures               April 2018

               50e3eebdfed39cbdc3ce9704882a2072
   y[24]       c75e13527b7a581a556168783dc1e975
               45e31865ddc46b3c957835da252bb732
   y[25]       8d3ee2062445dfb85ef8c35f8e1f3371
               af34023cef626e0af1e0bc017351aae2
   y[26]       ab8f5c612ead0b729a1d059d02bfe18e
               fa971b7300e882360a93b025ff97e9e0
   y[27]       eec0f3f3f13039a17f88b0cf808f4884
               31606cb13f9241f40f44e537d302c64a
   y[28]       4f1f4ab949b9feefadcb71ab50ef27d6
               d6ca8510f150c85fb525bf25703df720
   y[29]       9b6066f09c37280d59128d2f0f637c7d
               7d7fad4ed1c1ea04e628d221e3d8db77
   y[30]       b7c878c9411cafc5071a34a00f4cf077
               38912753dfce48f07576f0d4f94f42c6
   y[31]       d76f7ce973e9367095ba7e9a3649b7f4
               61d9f9ac1332a4d1044c96aefee67676
   y[32]       401b64457c54d65fef6500c59cdfb69a
               f7b6dddfcb0f086278dd8ad0686078df
   y[33]       b0f3f79cd893d314168648499898fbc0
               ced5f95b74e8ff14d735cdea968bee74
   --------------------------------------------
   LMS type    00000005                         # LM_SHA256_M32_H5
   path[0]     d8b8112f9200a5e50c4a262165bd342c
               d800b8496810bc716277435ac376728d
   path[1]     129ac6eda839a6f357b5a04387c5ce97
               382a78f2a4372917eefcbf93f63bb591
   path[2]     12f5dbe400bd49e4501e859f885bf073
               6e90a509b30a26bfac8c17b5991c157e
   path[3]     b5971115aa39efd8d564a6b90282c316
               8af2d30ef89d51bf14654510a12b8a14
   path[4]     4cca1848cf7da59cc2b3d9d0692dd2a2
               0ba3863480e25b1b85ee860c62bf5136
   --------------------------------------------
   LMS public key
   LMS type    00000005                         # LM_SHA256_M32_H5
   LMOTS type  00000004                         # LMOTS_SHA256_N32_W8
   I           d2f14ff6346af964569f7d6cb880a1b6
   K           6c5004917da6eafe4d9ef6c6407b3db0
               e5485b122d9ebe15cda93cfec582d7ab
   --------------------------------------------
   final_signature:
   --------------------------------------------
   LMS signature
   q           0000000a
   --------------------------------------------
   LMOTS signature
   LMOTS type  00000004                         # LMOTS_SHA256_N32_W8

McGrew, et al.           Expires October 7, 2018               [Page 48]
Internet-Draft            Hash-Based Signatures               April 2018

   C           0703c491e7558b35011ece3592eaa5da
               4d918786771233e8353bc4f62323185c
   y[0]        95cae05b899e35dffd71705470620998
               8ebfdf6e37960bb5c38d7657e8bffeef
   y[1]        9bc042da4b4525650485c66d0ce19b31
               7587c6ba4bffcc428e25d08931e72dfb
   y[2]        6a120c5612344258b85efdb7db1db9e1
               865a73caf96557eb39ed3e3f426933ac
   y[3]        9eeddb03a1d2374af7bf771855774562
               37f9de2d60113c23f846df26fa942008
   y[4]        a698994c0827d90e86d43e0df7f4bfcd
               b09b86a373b98288b7094ad81a0185ac
   y[5]        100e4f2c5fc38c003c1ab6fea479eb2f
               5ebe48f584d7159b8ada03586e65ad9c
   y[6]        969f6aecbfe44cf356888a7b15a3ff07
               4f771760b26f9c04884ee1faa329fbf4
   y[7]        e61af23aee7fa5d4d9a5dfcf43c4c26c
               e8aea2ce8a2990d7ba7b57108b47dabf
   y[8]        beadb2b25b3cacc1ac0cef346cbb90fb
               044beee4fac2603a442bdf7e507243b7
   y[9]        319c9944b1586e899d431c7f91bcccc8
               690dbf59b28386b2315f3d36ef2eaa3c
   y[10]       f30b2b51f48b71b003dfb08249484201
               043f65f5a3ef6bbd61ddfee81aca9ce6
   y[11]       0081262a00000480dcbc9a3da6fbef5c
               1c0a55e48a0e729f9184fcb1407c3152
   y[12]       9db268f6fe50032a363c9801306837fa
               fabdf957fd97eafc80dbd165e435d0e2
   y[13]       dfd836a28b354023924b6fb7e48bc0b3
               ed95eea64c2d402f4d734c8dc26f3ac5
   y[14]       91825daef01eae3c38e3328d00a77dc6
               57034f287ccb0f0e1c9a7cbdc828f627
   y[15]       205e4737b84b58376551d44c12c3c215
               c812a0970789c83de51d6ad787271963
   y[16]       327f0a5fbb6b5907dec02c9a90934af5
               a1c63b72c82653605d1dcce51596b3c2
   y[17]       b45696689f2eb382007497557692caac
               4d57b5de9f5569bc2ad0137fd47fb47e
   y[18]       664fcb6db4971f5b3e07aceda9ac130e
               9f38182de994cff192ec0e82fd6d4cb7
   y[19]       f3fe00812589b7a7ce51544045643301
               6b84a59bec6619a1c6c0b37dd1450ed4
   y[20]       f2d8b584410ceda8025f5d2d8dd0d217
               6fc1cf2cc06fa8c82bed4d944e71339e
   y[21]       ce780fd025bd41ec34ebff9d4270a322
               4e019fcb444474d482fd2dbe75efb203
   y[22]       89cc10cd600abb54c47ede93e08c114e
               db04117d714dc1d525e11bed8756192f

McGrew, et al.           Expires October 7, 2018               [Page 49]
Internet-Draft            Hash-Based Signatures               April 2018

   y[23]       929d15462b939ff3f52f2252da2ed64d
               8fae88818b1efa2c7b08c8794fb1b214
   y[24]       aa233db3162833141ea4383f1a6f120b
               e1db82ce3630b3429114463157a64e91
   y[25]       234d475e2f79cbf05e4db6a9407d72c6
               bff7d1198b5c4d6aad2831db61274993
   y[26]       715a0182c7dc8089e32c8531deed4f74
               31c07c02195eba2ef91efb5613c37af7
   y[27]       ae0c066babc69369700e1dd26eddc0d2
               16c781d56e4ce47e3303fa73007ff7b9
   y[28]       49ef23be2aa4dbf25206fe45c20dd888
               395b2526391a724996a44156beac8082
   y[29]       12858792bf8e74cba49dee5e8812e019
               da87454bff9e847ed83db07af3137430
   y[30]       82f880a278f682c2bd0ad6887cb59f65
               2e155987d61bbf6a88d36ee93b6072e6
   y[31]       656d9ccbaae3d655852e38deb3a2dcf8
               058dc9fb6f2ab3d3b3539eb77b248a66
   y[32]       1091d05eb6e2f297774fe6053598457c
               c61908318de4b826f0fc86d4bb117d33
   y[33]       e865aa805009cc2918d9c2f840c4da43
               a703ad9f5b5806163d7161696b5a0adc
   --------------------------------------------
   LMS type    00000005                         # LM_SHA256_M32_H5
   path[0]     d5c0d1bebb06048ed6fe2ef2c6cef305
               b3ed633941ebc8b3bec9738754cddd60
   path[1]     e1920ada52f43d055b5031cee6192520
               d6a5115514851ce7fd448d4a39fae2ab
   path[2]     2335b525f484e9b40d6a4a969394843b
               dcf6d14c48e8015e08ab92662c05c6e9
   path[3]     f90b65a7a6201689999f32bfd368e5e3
               ec9cb70ac7b8399003f175c40885081a
   path[4]     09ab3034911fe125631051df0408b394
               6b0bde790911e8978ba07dd56c73e7ee

   Test Case 2 Private Key

   --------------------------------------------
   (note: procedure in Appendix A is used)
   SEED        000102030405060708090a0b0c0d0e0f
               101112131415161718191a1b1c1d1e1f
   I           d08fabd4a2091ff0a8cb4ed834e74534
   --------------------------------------------
   --------------------------------------------

McGrew, et al.           Expires October 7, 2018               [Page 50]
Internet-Draft            Hash-Based Signatures               April 2018

   Test Case 2 Public Key

   --------------------------------------------
   HSS public key
   levels      00000002
   --------------------------------------------
   LMS type    00000006                         # LM_SHA256_M32_H10
   LMOTS type  00000003                         # LMOTS_SHA256_N32_W4
   I           d08fabd4a2091ff0a8cb4ed834e74534
   K           32a58885cd9ba0431235466bff9651c6
               c92124404d45fa53cf161c28f1ad5a8e
   --------------------------------------------
   --------------------------------------------

   Test Case 2 Message

   --------------------------------------------
   Message     54686520656e756d65726174696f6e20 The enumeration
               696e2074686520436f6e737469747574 in the Constitut
               696f6e2c206f66206365727461696e20 ion, of certain
               7269676874732c207368616c6c206e6f rights, shall no
               7420626520636f6e7374727565642074 t be construed t
               6f2064656e79206f7220646973706172 o deny or dispar
               616765206f7468657273207265746169 age others retai
               6e6564206279207468652070656f706c ned by the peopl
               652e0a                           e..
   --------------------------------------------

   Test Case 2 Signature

   --------------------------------------------
   HSS signature
   Nspk        00000001
   sig[0]:
   --------------------------------------------
   LMS signature
   q           00000003
   --------------------------------------------
   LMOTS signature
   LMOTS type  00000003                         # LMOTS_SHA256_N32_W4
   C           3d46bee8660f8f215d3f96408a7a64cf
               1c4da02b63a55f62c666ef5707a914ce
   y[0]        0674e8cb7a55f0c48d484f31f3aa4af9
               719a74f22cf823b94431d01c926e2a76
   y[1]        bb71226d279700ec81c9e95fb11a0d10
               d065279a5796e265ae17737c44eb8c59
   y[2]        4508e126a9a7870bf4360820bdeb9a01
               d9693779e416828e75bddd7d8c70d50a

McGrew, et al.           Expires October 7, 2018               [Page 51]
Internet-Draft            Hash-Based Signatures               April 2018

   y[3]        0ac8ba39810909d445f44cb5bb58de73
               7e60cb4345302786ef2c6b14af212ca1
   y[4]        9edeaa3bfcfe8baa6621ce88480df237
               1dd37add732c9de4ea2ce0dffa53c926
   y[5]        49a18d39a50788f4652987f226a1d481
               68205df6ae7c58e049a25d4907edc1aa
   y[6]        90da8aa5e5f7671773e941d805536021
               5c6b60dd35463cf2240a9c06d694e9cb
   y[7]        54e7b1e1bf494d0d1a28c0d31acc7516
               1f4f485dfd3cb9578e836ec2dc722f37
   y[8]        ed30872e07f2b8bd0374eb57d22c614e
               09150f6c0d8774a39a6e168211035dc5
   y[9]        2988ab46eaca9ec597fb18b4936e66ef
               2f0df26e8d1e34da28cbb3af75231372
   y[10]       0c7b345434f72d65314328bbb030d0f0
               f6d5e47b28ea91008fb11b05017705a8
   y[11]       be3b2adb83c60a54f9d1d1b2f476f9e3
               93eb5695203d2ba6ad815e6a111ea293
   y[12]       dcc21033f9453d49c8e5a6387f588b1e
               a4f706217c151e05f55a6eb7997be09d
   y[13]       56a326a32f9cba1fbe1c07bb49fa04ce
               cf9df1a1b815483c75d7a27cc88ad1b1
   y[14]       238e5ea986b53e087045723ce16187ed
               a22e33b2c70709e53251025abde89396
   y[15]       45fc8c0693e97763928f00b2e3c75af3
               942d8ddaee81b59a6f1f67efda0ef81d
   y[16]       11873b59137f67800b35e81b01563d18
               7c4a1575a1acb92d087b517a8833383f
   y[17]       05d357ef4678de0c57ff9f1b2da61dfd
               e5d88318bcdde4d9061cc75c2de3cd47
   y[18]       40dd7739ca3ef66f1930026f47d9ebaa
               713b07176f76f953e1c2e7f8f271a6ca
   y[19]       375dbfb83d719b1635a7d8a138919579
               44b1c29bb101913e166e11bd5f34186f
   y[20]       a6c0a555c9026b256a6860f4866bd6d0
               b5bf90627086c6149133f8282ce6c9b3
   y[21]       622442443d5eca959d6c14ca8389d12c
               4068b503e4e3c39b635bea245d9d05a2
   y[22]       558f249c9661c0427d2e489ca5b5dde2
               20a90333f4862aec793223c781997da9
   y[23]       8266c12c50ea28b2c438e7a379eb106e
               ca0c7fd6006e9bf612f3ea0a454ba3bd
   y[24]       b76e8027992e60de01e9094fddeb3349
               883914fb17a9621ab929d970d101e45f
   y[25]       8278c14b032bcab02bd15692d21b6c5c
               204abbf077d465553bd6eda645e6c306
   y[26]       5d33b10d518a61e15ed0f092c3222628
               1a29c8a0f50cde0a8c66236e29c2f310

McGrew, et al.           Expires October 7, 2018               [Page 52]
Internet-Draft            Hash-Based Signatures               April 2018

   y[27]       a375cebda1dc6bb9a1a01dae6c7aba8e
               bedc6371a7d52aacb955f83bd6e4f84d
   y[28]       2949dcc198fb77c7e5cdf6040b0f84fa
               f82808bf985577f0a2acf2ec7ed7c0b0
   y[29]       ae8a270e951743ff23e0b2dd12e9c3c8
               28fb5598a22461af94d568f29240ba28
   y[30]       20c4591f71c088f96e095dd98beae456
               579ebbba36f6d9ca2613d1c26eee4d8c
   y[31]       73217ac5962b5f3147b492e8831597fd
               89b64aa7fde82e1974d2f6779504dc21
   y[32]       435eb3109350756b9fdabe1c6f368081
               bd40b27ebcb9819a75d7df8bb07bb05d
   y[33]       b1bab705a4b7e37125186339464ad8fa
               aa4f052cc1272919fde3e025bb64aa8e
   y[34]       0eb1fcbfcc25acb5f718ce4f7c2182fb
               393a1814b0e942490e52d3bca817b2b2
   y[35]       6e90d4c9b0cc38608a6cef5eb153af08
               58acc867c9922aed43bb67d7b33acc51
   y[36]       9313d28d41a5c6fe6cf3595dd5ee63f0
               a4c4065a083590b275788bee7ad875a7
   y[37]       f88dd73720708c6c6c0ecf1f43bbaada
               e6f208557fdc07bd4ed91f88ce4c0de8
   y[38]       42761c70c186bfdafafc444834bd3418
               be4253a71eaf41d718753ad07754ca3e
   y[39]       ffd5960b0336981795721426803599ed
               5b2b7516920efcbe32ada4bcf6c73bd2
   y[40]       9e3fa152d9adeca36020fdeeee1b7395
               21d3ea8c0da497003df1513897b0f547
   y[41]       94a873670b8d93bcca2ae47e64424b74
               23e1f078d9554bb5232cc6de8aae9b83
   y[42]       fa5b9510beb39ccf4b4e1d9c0f19d5e1
               7f58e5b8705d9a6837a7d9bf99cd1338
   y[43]       7af256a8491671f1f2f22af253bcff54
               b673199bdb7d05d81064ef05f80f0153
   y[44]       d0be7919684b23da8d42ff3effdb7ca0
               985033f389181f47659138003d712b5e
   y[45]       c0a614d31cc7487f52de8664916af79c
               98456b2c94a8038083db55391e347586
   y[46]       2250274a1de2584fec975fb09536792c
               fbfcf6192856cc76eb5b13dc4709e2f7
   y[47]       301ddff26ec1b23de2d188c999166c74
               e1e14bbc15f457cf4e471ae13dcbdd9c
   y[48]       50f4d646fc6278e8fe7eb6cb5c94100f
               a870187380b777ed19d7868fd8ca7ceb
   y[49]       7fa7d5cc861c5bdac98e7495eb0a2cee
               c1924ae979f44c5390ebedddc65d6ec1
   y[50]       1287d978b8df064219bc5679f7d7b264
               a76ff272b2ac9f2f7cfc9fdcfb6a5142

McGrew, et al.           Expires October 7, 2018               [Page 53]
Internet-Draft            Hash-Based Signatures               April 2018

   y[51]       8240027afd9d52a79b647c90c2709e06
               0ed70f87299dd798d68f4fadd3da6c51
   y[52]       d839f851f98f67840b964ebe73f8cec4
               1572538ec6bc131034ca2894eb736b3b
   y[53]       da93d9f5f6fa6f6c0f03ce43362b8414
               940355fb54d3dfdd03633ae108f3de3e
   y[54]       bc85a3ff51efeea3bc2cf27e1658f178
               9ee612c83d0f5fd56f7cd071930e2946
   y[55]       beeecaa04dccea9f97786001475e0294
               bc2852f62eb5d39bb9fbeef75916efe4
   y[56]       4a662ecae37ede27e9d6eadfdeb8f8b2
               b2dbccbf96fa6dbaf7321fb0e701f4d4
   y[57]       29c2f4dcd153a2742574126e5eaccc77
               686acf6e3ee48f423766e0fc466810a9
   y[58]       05ff5453ec99897b56bc55dd49b99114
               2f65043f2d744eeb935ba7f4ef23cf80
   y[59]       cc5a8a335d3619d781e7454826df720e
               ec82e06034c44699b5f0c44a8787752e
   y[60]       057fa3419b5bb0e25d30981e41cb1361
               322dba8f69931cf42fad3f3bce6ded5b
   y[61]       8bfc3d20a2148861b2afc14562ddd27f
               12897abf0685288dcc5c4982f8260268
   y[62]       46a24bf77e383c7aacab1ab692b29ed8
               c018a65f3dc2b87ff619a633c41b4fad
   y[63]       b1c78725c1f8f922f6009787b1964247
               df0136b1bc614ab575c59a16d089917b
   y[64]       d4a8b6f04d95c581279a139be09fcf6e
               98a470a0bceca191fce476f9370021cb
   y[65]       c05518a7efd35d89d8577c990a5e1996
               1ba16203c959c91829ba7497cffcbb4b
   y[66]       294546454fa5388a23a22e805a5ca35f
               956598848bda678615fec28afd5da61a
   --------------------------------------------
   LMS type    00000006                         # LM_SHA256_M32_H10
   path[0]     b326493313053ced3876db9d23714818
               1b7173bc7d042cefb4dbe94d2e58cd21
   path[1]     a769db4657a103279ba8ef3a629ca84e
               e836172a9c50e51f45581741cf808315
   path[2]     0b491cb4ecbbabec128e7c81a46e62a6
               7b57640a0a78be1cbf7dd9d419a10cd8
   path[3]     686d16621a80816bfdb5bdc56211d72c
               a70b81f1117d129529a7570cf79cf52a
   path[4]     7028a48538ecdd3b38d3d5d62d262465
               95c4fb73a525a5ed2c30524ebb1d8cc8
   path[5]     2e0c19bc4977c6898ff95fd3d310b0ba
               e71696cef93c6a552456bf96e9d075e3
   path[6]     83bb7543c675842bafbfc7cdb88483b3
               276c29d4f0a341c2d406e40d4653b7e4

McGrew, et al.           Expires October 7, 2018               [Page 54]
Internet-Draft            Hash-Based Signatures               April 2018

   path[7]     d045851acf6a0a0ea9c710b805cced46
               35ee8c107362f0fc8d80c14d0ac49c51
   path[8]     6703d26d14752f34c1c0d2c4247581c1
               8c2cf4de48e9ce949be7c888e9caebe4
   path[9]     a415e291fd107d21dc1f084b11582082
               49f28f4f7c7e931ba7b3bd0d824a4570
   --------------------------------------------
   LMS public key
   LMS type    00000005                         # LM_SHA256_M32_H5
   LMOTS type  00000004                         # LMOTS_SHA256_N32_W8
   I           215f83b7ccb9acbcd08db97b0d04dc2b
   K           a1cd035833e0e90059603f26e07ad2aa
               d152338e7a5e5984bcd5f7bb4eba40b7
   --------------------------------------------
   final_signature:
   --------------------------------------------
   LMS signature
   q           00000004
   --------------------------------------------
   LMOTS signature
   LMOTS type  00000004                         # LMOTS_SHA256_N32_W8
   C           0eb1ed54a2460d512388cad533138d24
               0534e97b1e82d33bd927d201dfc24ebb
   y[0]        11b3649023696f85150b189e50c00e98
               850ac343a77b3638319c347d7310269d
   y[1]        3b7714fa406b8c35b021d54d4fdada7b
               9ce5d4ba5b06719e72aaf58c5aae7aca
   y[2]        057aa0e2e74e7dcfd17a0823429db629
               65b7d563c57b4cec942cc865e29c1dad
   y[3]        83cac8b4d61aacc457f336e6a10b6632
               3f5887bf3523dfcadee158503bfaa89d
   y[4]        c6bf59daa82afd2b5ebb2a9ca6572a60
               67cee7c327e9039b3b6ea6a1edc7fdc3
   y[5]        df927aade10c1c9f2d5ff446450d2a39
               98d0f9f6202b5e07c3f97d2458c69d3c
   y[6]        8190643978d7a7f4d64e97e3f1c4a08a
               7c5bc03fd55682c017e2907eab07e5bb
   y[7]        2f190143475a6043d5e6d5263471f4ee
               cf6e2575fbc6ff37edfa249d6cda1a09
   y[8]        f797fd5a3cd53a066700f45863f04b6c
               8a58cfd341241e002d0d2c0217472bf1
   y[9]        8b636ae547c1771368d9f317835c9b0e
               f430b3df4034f6af00d0da44f4af7800
   y[10]       bc7a5cf8a5abdb12dc718b559b74cab9
               090e33cc58a955300981c420c4da8ffd
   y[11]       67df540890a062fe40dba8b2c1c548ce
               d22473219c534911d48ccaabfb71bc71
   y[12]       862f4a24ebd376d288fd4e6fb06ed870

McGrew, et al.           Expires October 7, 2018               [Page 55]
Internet-Draft            Hash-Based Signatures               April 2018

               5787c5fedc813cd2697e5b1aac1ced45
   y[13]       767b14ce88409eaebb601a93559aae89
               3e143d1c395bc326da821d79a9ed41dc
   y[14]       fbe549147f71c092f4f3ac522b5cc572
               90706650487bae9bb5671ecc9ccc2ce5
   y[15]       1ead87ac01985268521222fb9057df7e
               d41810b5ef0d4f7cc67368c90f573b1a
   y[16]       c2ce956c365ed38e893ce7b2fae15d36
               85a3df2fa3d4cc098fa57dd60d2c9754
   y[17]       a8ade980ad0f93f6787075c3f680a2ba
               1936a8c61d1af52ab7e21f416be09d2a
   y[18]       8d64c3d3d8582968c2839902229f85ae
               e297e717c094c8df4a23bb5db658dd37
   y[19]       7bf0f4ff3ffd8fba5e383a48574802ed
               545bbe7a6b4753533353d73706067640
   y[20]       135a7ce517279cd683039747d218647c
               86e097b0daa2872d54b8f3e508598762
   y[21]       9547b830d8118161b65079fe7bc59a99
               e9c3c7380e3e70b7138fe5d9be255150
   y[22]       2b698d09ae193972f27d40f38dea264a
               0126e637d74ae4c92a6249fa103436d3
   y[23]       eb0d4029ac712bfc7a5eacbdd7518d6d
               4fe903a5ae65527cd65bb0d4e9925ca2
   y[24]       4fd7214dc617c150544e423f450c99ce
               51ac8005d33acd74f1bed3b17b7266a4
   y[25]       a3bb86da7eba80b101e15cb79de9a207
               852cf91249ef480619ff2af8cabca831
   y[26]       25d1faa94cbb0a03a906f683b3f47a97
               c871fd513e510a7a25f283b196075778
   y[27]       496152a91c2bf9da76ebe089f4654877
               f2d586ae7149c406e663eadeb2b5c7e8
   y[28]       2429b9e8cb4834c83464f079995332e4
               b3c8f5a72bb4b8c6f74b0d45dc6c1f79
   y[29]       952c0b7420df525e37c15377b5f09843
               19c3993921e5ccd97e097592064530d3
   y[30]       3de3afad5733cbe7703c5296263f7734
               2efbf5a04755b0b3c997c4328463e84c
   y[31]       aa2de3ffdcd297baaaacd7ae646e44b5
               c0f16044df38fabd296a47b3a838a913
   y[32]       982fb2e370c078edb042c84db34ce36b
               46ccb76460a690cc86c302457dd1cde1
   y[33]       97ec8075e82b393d542075134e2a17ee
               70a5e187075d03ae3c853cff60729ba4
   --------------------------------------------
   LMS type    00000005                         # LM_SHA256_M32_H5
   path[0]     4de1f6965bdabc676c5a4dc7c35f97f8
               2cb0e31c68d04f1dad96314ff09e6b3d
   path[1]     e96aeee300d1f68bf1bca9fc58e40323

McGrew, et al.           Expires October 7, 2018               [Page 56]
Internet-Draft            Hash-Based Signatures               April 2018

               36cd819aaf578744e50d1357a0e42867
   path[2]     04d341aa0a337b19fe4bc43c2e79964d
               4f351089f2e0e41c7c43ae0d49e7f404
   path[3]     b0f75be80ea3af098c9752420a8ac0ea
               2bbb1f4eeba05238aef0d8ce63f0c6e5
   path[4]     e4041d95398a6f7f3e0ee97cc1591849
               d4ed236338b147abde9f51ef9fd4e1c1

Authors' Addresses

   David McGrew
   Cisco Systems
   13600 Dulles Technology Drive
   Herndon, VA  20171
   USA

   Email: mcgrew@cisco.com

   Michael Curcio
   Cisco Systems
   7025-2 Kit Creek Road
   Research Triangle Park, NC  27709-4987
   USA

   Email: micurcio@cisco.com

   Scott Fluhrer
   Cisco Systems
   170 West Tasman Drive
   San Jose, CA
   USA

   Email: sfluhrer@cisco.com

McGrew, et al.           Expires October 7, 2018               [Page 57]