Skip to main content

TRILL OAM MIB
draft-ietf-trill-oam-mib-08

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 7784.
Authors Deepak Kumar , Samer Salam , Tissa Senevirathne
Last updated 2015-08-23
Replaces draft-deepak-trill-oam-mib
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state Submitted to IESG for Publication
Document shepherd Donald E. Eastlake 3rd
Shepherd write-up Show Last changed 2015-06-30
IESG IESG state Became RFC 7784 (Proposed Standard)
Consensus boilerplate Yes
Telechat date (None)
Responsible AD Alia Atlas
Send notices to d3e3e3@gmail.com, trill-chairs@ietf.org
IANA IANA review state Version Changed - Review Needed
draft-ietf-trill-oam-mib-08
TRILL Working Group                                         Deepak Kumar
Internet Draft                                               Samer Salam
                                                                   Cisco
Intended Status: Standard Track                       Tissa Senevirathne
                                                              Consultant
Expires January 2016                                     August 23, 2015

                             TRILL OAM MIB
                    draft-ietf-trill-oam-mib-08.txt

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79. 

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF), its areas, and its working groups.  Note that
   other groups may also distribute working documents as Internet-
   Drafts.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   The list of current Internet-Drafts can be accessed at
   http://www.ietf.org/ietf/1id-abstracts.txt.

   The list of Internet-Draft Shadow Directories can be accessed at
   http://www.ietf.org/shadow.html.

   This Internet-Draft will expire on February 24, 2016.

Copyright Notice

   Copyright (c) 2015 IETF Trust and the persons identified as the
   document authors.  All rights reserved.   

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License. 

 

Kumar et al.           Expires February 24, 2016                [Page 1]
Internet Draft               TRILL OAM MIB               August 23, 2015

Abstract          

   This document specifies the Management Information Base (MIB) for the
   IETF TRILL (Transparent Interconnection of Lots of Links) OAM
   (Operations, Administration, and Maintenance) objects.

Table of Contents

   1. Introduction  . . . . . . . . . . . . . . . . . . . . . . . . .  2
   2. The Internet-Standard Management Framework  . . . . . . . . . .  3
   3. Overview  . . . . . . . . . . . . . . . . . . . . . . . . . . .  3
   4. Conventions . . . . . . . . . . . . . . . . . . . . . . . . . .  3
   5. Structure of the MIB module . . . . . . . . . . . . . . . . . .  4
     5.1. Textual Conventions . . . . . . . . . . . . . . . . . . . .  4
     5.2.  TRILL-OAM-MIB relationship to IEEE8021-TC-MIB  . . . . . .  4
     5.3.  TRILL OAM MIB Tree . . . . . . . . . . . . . . . . . . . .  5
       5.3.1.  TRILL OAM MIB Notifications  . . . . . . . . . . . . .  5
       5.3.2. TRILL OAM MIB Per MEP Objects . . . . . . . . . . . . .  5
         5.3.2.1. trillOamMepTable Objects  . . . . . . . . . . . . .  5
         5.3.2.2. trillOamMepFlowCfgTable Objects . . . . . . . . . .  6
         5.3.2.3. trillOamPtrTable Objects  . . . . . . . . . . . . .  6
         5.3.2.4. trillOamMtvrTable Objects . . . . . . . . . . . . .  6
         5.3.2.5. trillOamMepDbTable Objects  . . . . . . . . . . . .  6
   6. Relationship to other MIB module  . . . . . . . . . . . . . . .  7
     6.1. Relationship to IEEE8021-CFM-MIB  . . . . . . . . . . . . .  7
     6.2.  MIB modules required for IMPORTS . . . . . . . . . . . . .  8
   7. Definition of the TRILL OAM MIB module  . . . . . . . . . . . .  8
   8. Security Considerations . . . . . . . . . . . . . . . . . . . . 43
   9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . . 45
   10.  References  . . . . . . . . . . . . . . . . . . . . . . . . . 45
     10.1.  Normative References  . . . . . . . . . . . . . . . . . . 45
     10.2.  Informative References  . . . . . . . . . . . . . . . . . 46
   11.  Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 47
   12. Copyright and Disclaimer . . . . . . . . . . . . . . . . . . . 47

1. Introduction

   Overall, TRILL OAM is intended to meet the requirements given in
   [RFC6905]. The general framework for TRILL OAM is specified in
   [RFC7174]. The details of the Fault Management (FM) solution,
   conforming to that framework, are presented in RFC 7455. The solution
   leverages the message format defined in Ethernet Connectivity Fault
   Management (CFM) [802.1Q] as the basis for the TRILL OAM message
   channel.

 

Kumar et al.           Expires February 24, 2016                [Page 2]
Internet Draft               TRILL OAM MIB               August 23, 2015

   This document uses the CFM MIB modules defined in [802.1Q] as the
   basis for TRILL OAM MIB, and augments the existing tables to add new
   TRILL managed objects required by TRILL. This document further
   specifies a new table with associated managed objects for TRILL OAM
   specific capabilities.

2. The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB. MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI). This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

3. Overview

   The TRILL-OAM-MIB module is intended to provide an overall framework
   for managing TRILL OAM. It leverages the IEEE8021-CFM-MIB and
   IEEE8021-CFM-V2-MIB modules defined in [802.1Q], and augments the
   Maintenance End Point(MEP) and MEP Db entries. It also adds a new
   table for TRILL OAM specific messages. 

4. Conventions

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in
   RFC-2119 [RFC2119]. 

   Acronyms used in the document include the following:
   MTVM  - Multi-destination Tree Verification Message [RFC7455]

   MTVR  - Multi-destination Tree Verification Reply [RFC7455]

   PTM   - Path Trace Message [RFC7455]

   PTR   - Path Trace Reply [RFC7455]

   MEP   - Maintenance End Point [RFC7174] [802.1Q]

 

Kumar et al.           Expires February 24, 2016                [Page 3]
Internet Draft               TRILL OAM MIB               August 23, 2015

   MIP   - Maintenance Intermediate Point [RFC7174] [802.1Q]

   MP    - Maintenance Point [RFC7174]

   CCM   - Continuity Check Message [802.1Q]

   FGL   - Fine-Grained Label

   LBM   - Loopback Message [802.1Q]

   LBR   - Loopback Reply [802.1Q]

   TRILL - Transparent Interconnection of Lots of Links [RFC6325]

5. Structure of the MIB module

Objects in this MIB module are arranged into subtrees. Each subtree is
organized as a set of related objects. The various subtrees are shown
below, supplemented with the required elements of the IEEE8021-CFM-MIB
module.

5.1. Textual Conventions

Textual conventions are defined to represent object types relevant to
the TRILL OAM MIB. 

5.2.  TRILL-OAM-MIB relationship to IEEE8021-TC-MIB

In TRILL, traffic labeling can be done using either a 12-bit VLAN or a
24-bit fine grain label [RFC7172]. 

The IEEE8021-TC-MIB definition of IEEE8021ServiceSelectorType includes
the two values:

- 1 representing a vlanId, and

- 2 representing a 24 bit isid 

We have chosen to use value 2 for TRILL's fine grain label. As such,
TRILL-OAM-MIB will import IEEE8021ServiceSelectorType,
IEEE8021ServiceSelectorValueOrNone, and IEEE8021ServiceSelectorValue
from IEEE8021-TC-MIB.

 

Kumar et al.           Expires February 24, 2016                [Page 4]
Internet Draft               TRILL OAM MIB               August 23, 2015

5.3.  TRILL OAM MIB Tree

TRILL-OAM MIB Tree describe below consists of trilloamNotifications
(Traps) and trillOamMibObjects. trilloamNotifications are sent to
management entity whenever a MEP loses/restores contact with its peer
Flow MEPs.

The TRILL OAM MIB Per MEP Objects are defined in the trillOamMepTable.
The trillOamMepTable augments the dot1agCfmMepEntry (please see section
6.1) defined in IEEE8021-CFM-MIB. It includes objects that are locally
defined for an individual MEP and its associated Flow.

TRILL-OAM-MIB

  |--trillOamNotifications          (trillOamMib 0}

     |--trillOamFaultAlarm

  |--trillOamMibObjects             {trillOamMib 1}

     |--trillOamMep                 {trillOamMibObjects 1}

        |--trillOamMepTable         {trillOamMep 1}  - Local TRLL config

        |--trillOamMepFlowCfgTable

        |--trillOamPtrTable

        |--trillOamMtvrTable

        |--trillOamMepDbTable

5.3.1.  TRILL OAM MIB Notifications

Notifications (fault alarm) are sent to the management entity with the
OID of the MEP that has detected the fault. Notifications are generated
whenever MEP loses/restores contact with its peer Flow MEPs.

5.3.2. TRILL OAM MIB Per MEP Objects

The TRILL OAM MIB Per MEP Objects are defined in the trillOamMepTable.
The trillOamMepTable augments the dot1agCfmMepEntry (please see section
6.1) defined in IEEE8021-CFM-MIB. It includes objects that are locally
defined for an individual MEP and its associated Flow.

5.3.2.1. trillOamMepTable Objects

 

Kumar et al.           Expires February 24, 2016                [Page 5]
Internet Draft               TRILL OAM MIB               August 23, 2015

   This table is an extension of the dot1agCfmMepTable and rows are
   automatically added or deleted from this table based upon row
   creation and destruction of the dot1agCfmMepTable. 

   This table represents the local MEP TRILL OAM configuration table.
   The primary purpose of this table is provide local parameters for the
   TRILL OAM function found in RFC 7455 and instantiated at a MEP.

5.3.2.2. trillOamMepFlowCfgTable Objects

   Each row in this table represents a Flow Configuration Entry for the
   associated MEP. This table uses four indices. The first three indices
   are the indices of the Maintenance Domain, MaNet, and MEP tables. The
   fourth index is the specific Flow Configuration Entry on the selected
   MEP. Some write-able objects in this table are only applicable in
   certain cases (as described under each object below), and attempts to
   write values for them in other cases will be ignored.

5.3.2.3. trillOamPtrTable Objects

   Each row in this table represents a Path Trace reply Entry for the
   Defined MEP and Transaction. This table uses four indices. The first
   three indices identify the MEP and the fourth index specifies the
   transaction identifier. This transaction identifier uniquely
   identifies the response for a MEP which can have multiple flow.

5.3.2.4. trillOamMtvrTable Objects

   This table includes managed objects for the Multi-Destination Reply.
   Each row in the table represents a Multi-destination Reply Entry for
   the defined MEP and Transaction. This table uses the following five
   indices: 1) Maintenance Domain, 2) MANET, 3) MEP tables, 4)
   Transaction identifier of selected MEP, and 5) receive order of
   Multi-destination replies.

   Some write-able objects in this table are only applicable in certain
   cases (as described under each object below), and attempts to write a
   value for them in other cases will be ignored.

5.3.2.5. trillOamMepDbTable Objects

   This table is an augmentation of the dot1agCfmMepDbTable, and rows
   are automatically added or deleted from this table based upon row
   creation and destruction of the dot1agCfmMepDbTable.

 

Kumar et al.           Expires February 24, 2016                [Page 6]
Internet Draft               TRILL OAM MIB               August 23, 2015

6. Relationship to other MIB module

   The IEEE8021-CFM-MIB, and LLDP-MIB contain objects relevant to TRILL
   OAM MIB. Management objects contained in these modules are not
   duplicated here, to reduce overlap to the extent possible. From
   IEEE8021-CFM-MIB following objects are imported 

      o dot1agCfmMdIndex

      o dot1agCfmMaIndex

      o dot1agCfmMepIdentifier

      o dot1agCfmMepEntry

      o dot1agCfmMepDbEntry

      o Dot1agCfmIngressActionFieldValue

      o Dot1agCfmEgressActionFieldValue

      o Dot1agCfmRemoteMepState

   From LLDP-MIB following objects are imported

      o LldpChassisId

      o LldpChassisIdSubtype

      o LldpPortId

6.1. Relationship to IEEE8021-CFM-MIB

   trillOamMepTable Augments dot1agCfmMepEntry. Implementation of
   IEEE8021-CFM-MIB is required as we are Augmenting the IEEE-CFM-MIB
   Table. Objects/Tables that are not applicable to a TRILL
   implementation have to be handled by the TRILL implementation back
   end and appropriate default values as described in IEEE8021-CFM-MIB
   have to be returned. 

   TRILL Implementation doesn't support Link Trace Message and Link
   Trace Reply as RFC7455 substituted it with Path Trace Message and
   Reply for unicast traffic and Multi-destination Tree verification
   Message and Reply for multicast traffic,  and statistics with respect
   of these message should be default as per IEEE8021-CFM-MIB.

 

Kumar et al.           Expires February 24, 2016                [Page 7]
Internet Draft               TRILL OAM MIB               August 23, 2015

6.2.  MIB modules required for IMPORTS

   The following MIB module IMPORTS objects from SNMPv2-SMI [RFC2578],
   SNMPv2-TC [RFC2579], SNMPv2-CONF [RFC2580], IEEE-8021-CFM-MIB, LLDP-
   MIB.

7. Definition of the TRILL OAM MIB module

   TRILL-OAM-MIB DEFINITIONS ::= BEGIN

   IMPORTS

       MODULE-IDENTITY,
       OBJECT-TYPE,
       Counter32,
       Unsigned32,
       Integer32,
       mib-2,
       NOTIFICATION-TYPE
          FROM SNMPv2-SMI
       RowStatus,
       TruthValue,
       TimeStamp,
       MacAddress
           FROM SNMPv2-TC
       OBJECT-GROUP,
       NOTIFICATION-GROUP,
       MODULE-COMPLIANCE
           FROM SNMPv2-CONF
       dot1agCfmMdIndex,
       dot1agCfmMaIndex,
       dot1agCfmMepIdentifier,
       dot1agCfmMepEntry,
       dot1agCfmMepDbEntry,
       Dot1agCfmIngressActionFieldValue,
       Dot1agCfmEgressActionFieldValue,
       Dot1agCfmRemoteMepState
           FROM IEEE8021-CFM-MIB
       LldpChassisId,
       LldpChassisIdSubtype,
       LldpPortId,
       LldpPortIdSubtype
           FROM LLDP-MIB;

   trillOamMib MODULE-IDENTITY
       LAST-UPDATED    "201508231200Z"
       ORGANIZATION    "IETF TRILL WG"
       CONTACT-INFO
 

Kumar et al.           Expires February 24, 2016                [Page 8]
Internet Draft               TRILL OAM MIB               August 23, 2015

               "E-mail: trill@ietf.org"
       DESCRIPTION
           "This MIB module contains the management objects for the
           management of Trill Services Operations, Administration
           and Maintenance.
           Initial version. Published as RFC xxxx.

           -------------------------------------------------------------
           Reference Overview

           A number of base documents have been used to create the 
           Textual Conventions MIB. The following are the 
           abbreviations for the baseline documents:

           [CFM] refers to 'Connectivity Fault Management', 
           IEEE 802.1Q-2014, December 2014
           [Q.840.1] refers to 'ITU-T Requirements and analysis for 
           NMS-EMS management interface of Ethernet over Transport and 
           Metro Ethernet Network (EoT/MEN)', March 2007
           [Y.1731] refers to ITU-T Y.1731 'OAM functions and mechanisms
           for Ethernet based networks', February 2011
           -------------------------------------------------------------

           Abbreviations Used 

           Term         Definition
           CCM          Continuity Check Message
           CFM          Connectivity Fault Management 
           CoS          Class of Service 
           IEEE         Institute of Electrical and Electronics 
                        Engineers
           IETF         Internet Engineering Task Force
           ITU-T        International Telecommunication Union - 
                        Telecommunication Standardization Bureau
           MAC          Media Access Control 
           MA           Maintenance Association (equivalent to a MEG) 
           MD           Maintenance Domain (equivalent to a OAM 
                                            Domain in MEF 17) 
           MD Level     Maintenance Domain Level (equivalent to a 
                                                  MEG level) 
           ME           Maintenance Entity 
           MEG         Maintenance Entity Group (equivalent to a MA) 
           MEG Level   Maintenance Entity Group Level (equivalent to 
                                                       MD Level) 
           MEP         Maintenance Association End Point or MEG End 
                       Point 
           MIB         Management Information Base 
 

Kumar et al.           Expires February 24, 2016                [Page 9]
Internet Draft               TRILL OAM MIB               August 23, 2015

           MIP         Maintenance Domain Intermediate Point or 
                       MEG Intermediate Point 
           MP          Maintenance Point. One of either a MEP or a MIP 
           OAM         Operations, Administration, and Maintenance 
                       On-Demand OAM actions that are initiated via 
                       manual intervention for a limited time to carry 
                       out diagnostics.  On-Demand OAM can result in 
                       singular or periodic OAM actions during the 
                       diagnostic time interval 
           PDU         Protocol Data Unit 
           RFC         Request for Comment
           SNMP        Simple Network Management Protocol
           SNMP Agent  An SNMP entity containing one or more command 
                       responder and/or notification originator 
                       applications(along with their associated SNMP 
                       engine).  Typically implemented in Network 
                       Element. 
           SNMP Manager An SNMP entity containing one or more command 
                        generator and/or notification receiver 
                        applications (along with their associated SNMP 
                        engine). Typically implemented in an 
                        EMS or NMS. 
           TLV         Type Length Value, a method of encoding Objects
           UTC         Coordinated Universal Time 
           UNI         User-to-Network Interface 
           VLAN        Virtual LAN
           PTR         Path Trace Reply
           PTM         Path Trace Message
           MTVR        Multi-destination Tree Verification Reply
           MTVM        Multi-destination Tree Verification Message"

       REVISION        "201508231200Z"
       DESCRIPTION
           "Initial version. Published as RFC xxxx."
       ::= { mib-2 12000 }

   -- RFC Ed.: assigned by IANA, see section 9 for details
   --   
   -- *****************************************************************
   -- Object definitions in the TRILL OAM MIB Module
   -- *****************************************************************

   trillOamNotifications  OBJECT IDENTIFIER
       ::= { trillOamMib 0 }

   trillOamMibObjects  OBJECT IDENTIFIER
       ::= { trillOamMib 1 }
 

Kumar et al.           Expires February 24, 2016               [Page 10]
Internet Draft               TRILL OAM MIB               August 23, 2015

   trillOamMibConformance  OBJECT IDENTIFIER
       ::= { trillOamMib 2 }

   -- *****************************************************************
   -- Groups in the TRILL OAM MIB Module
   -- *****************************************************************

   trillOamMep  OBJECT IDENTIFIER
       ::= { trillOamMibObjects 1 }

   -- *****************************************************************
   -- TRILL OAM MEP Configuration
   -- *****************************************************************

   trillOamMepTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamMepEntry 
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table is an extension of the dot1agCfmMepTable and 
            rows are automatically added or deleted from this table 
            based upon row creation and destruction of the 
            dot1agCfmMepTable. 

           This table represents the local MEP TRILL OAM 
           configuration table. The primary purpose of this table 
           is provide local parameters for the TRILL OAM function 
           found in RFC 7455 and instantiated at a MEP."
       REFERENCE       "RFC 7455"
       ::= { trillOamMep 1 }

   trillOamMepEntry OBJECT-TYPE
       SYNTAX          TrillOamMepEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "The conceptual row of trillOamMepTable."
       AUGMENTS           { dot1agCfmMepEntry  } 
       ::= { trillOamMepTable 1 }

   TrillOamMepEntry ::= SEQUENCE {
           trillOamMepRName               Unsigned32,
           trillOamMepNextPtmTId          Counter32,
           trillOamMepNextMtvmTId         Counter32,
           trillOamMepPtrIn               Counter32,
           trillOamMepPtrInOutofOrder     Counter32,
           trillOamMepPtrOut              Counter32,
 

Kumar et al.           Expires February 24, 2016               [Page 11]
Internet Draft               TRILL OAM MIB               August 23, 2015

           trillOamMepMtvrIn              Counter32,
           trillOamMepMtvrInOutofOrder    Counter32,
           trillOamMepMtvrOut             Counter32,
           trillOamMepTxLbmDestRName      Unsigned32,
           trillOamMepTxLbmHC             Unsigned32,
           trillOamMepTxLbmReplyModeOob   TruthValue,
           trillOamMepTransmitLbmReplyIp  OCTET STRING,
           trillOamMepTxLbmFlowEntropy    OCTET STRING,
           trillOamMepTxPtmDestRName      Unsigned32,
           trillOamMepTxPtmHC             Unsigned32,
           trillOamMepTxPtmReplyModeOob   TruthValue,
           trillOamMepTransmitPtmReplyIp  OCTET STRING,
           trillOamMepTxPtmFlowEntropy    OCTET STRING,
           trillOamMepTxPtmStatus         TruthValue,
           trillOamMepTxPtmResultOK       TruthValue,
           trillOamMepTxPtmSeqNumber      Unsigned32,
           trillOamMepTxPtmMessages       Integer32,
           trillOamMepTxMtvmTree          Unsigned32,
           trillOamMepTxMtvmHC            Unsigned32,
           trillOamMepTxMtvmReplyModeOob  TruthValue,
           trillOamMepTransmitMtvmReplyIp OCTET STRING,
           trillOamMepTxMtvmFlowEntropy   OCTET STRING,
           trillOamMepTxMtvmStatus        TruthValue,
           trillOamMepTxMtvmResultOK      TruthValue,
           trillOamMepTxMtvmMessages      Integer32,
           trillOamMepTxMtvmSeqNumber     Unsigned32,
           trillOamMepTxMtvmScopeList     OCTET STRING,
           trillOamMepDiscontinuityTime   TimeStamp
   }

   trillOamMepRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "This object contains Rbridge NickName of TRILL Rbridge as
           defined in RFC 6325 section 3.7."
       REFERENCE "RFC 7455 and RFC 6325 section 3.7" 
       ::= { trillOamMepEntry 1 }

   trillOamMepNextPtmTId OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next sequence number/transaction identifier to be sent in a
            Multi-destination message. This sequence number can be zero
            because it wraps around. Implementation of this identifier 
 

Kumar et al.           Expires February 24, 2016               [Page 12]
Internet Draft               TRILL OAM MIB               August 23, 2015

            should be should provide a unique code value in order to
            identify Transaction Id for a MEP with multiple flows." 
       REFERENCE "RFC 7455 10.1.1"
       ::= { trillOamMepEntry 2 }

   trillOamMepNextMtvmTId OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next sequence number/transaction identifier to be sent in a
           Multi-destination message. This sequence number can be zero
           because it wraps around. Implementation should be unique to 
           identify Transaction Id for a MEP with multiple flows."
       REFERENCE "RFC 7455 11.2.1" 
       ::= { trillOamMepEntry 3 }

   trillOamMepPtrIn OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, in-order Path Trace Replies 
            received."
       REFERENCE "RFC 7455 section 10" 
       ::= { trillOamMepEntry 4 }

   trillOamMepPtrInOutofOrder OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, out-of-order Path Trace Replies 
            received."
       REFERENCE "RFC 7455 section 10" 
       ::= { trillOamMepEntry 5 }

   trillOamMepPtrOut OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, Path Trace Replies 
            transmitted."
       REFERENCE "RFC 7455 section 10" 
       ::= { trillOamMepEntry 6 }

   trillOamMepMtvrIn OBJECT-TYPE
 

Kumar et al.           Expires February 24, 2016               [Page 13]
Internet Draft               TRILL OAM MIB               August 23, 2015

       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, in-order Multi-destination 
            Replies received." 
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 7 }

   trillOamMepMtvrInOutofOrder OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, out-of-order Multi-destination 
            Replies received." 
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 8 }

   trillOamMepMtvrOut OBJECT-TYPE
       SYNTAX          Counter32
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Total number of valid, Multi-destination Replies
           transmitted." 
       REFERENCE "RFC 7455 section 11"
       ::= { trillOamMepEntry 9 }

   trillOamMepTxLbmDestRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Target Destination Rbridge NickName Field as
           defined in RFC 6325 section 3.7 to be transmitted."
       REFERENCE "RFC 7455 and RFC6325 section 3.7" 
       ::= { trillOamMepEntry 10 }

   trillOamMepTxLbmHC OBJECT-TYPE
       SYNTAX          Unsigned32(1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Hop Count to be transmitted.
           " 
       REFERENCE "RFC 7455 section 9 and 3"
       ::= { trillOamMepEntry 11 }
 

Kumar et al.           Expires February 24, 2016               [Page 14]
Internet Draft               TRILL OAM MIB               August 23, 2015

   trillOamMepTxLbmReplyModeOob OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "True Indicates that Reply of Lbm is out of band and
           out of band IP Address TLV is to be transmitted. 
           False indicates that In band reply is transmitted."
       REFERENCE "RFC 7455 9.2.1" 
       ::= { trillOamMepEntry 12 }

   trillOamMepTransmitLbmReplyIp OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (4..16))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "IP address for out of band IP Address TLV is to be 
            transmitted, Maximum length for IPv6 is 16 OCTET
            and IPv4 is 4 OCTET."
       REFERENCE "RFC 7455 section 3" 
       ::= { trillOamMepEntry 13 }

   trillOamMepTxLbmFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "96 Byte Flow Entropy as defined in RFC 7455 to be 
            transmitted."
       REFERENCE "RFC 7455 section 3" 
       ::= { trillOamMepEntry 14 }

   trillOamMepTxPtmDestRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Target Destination Rbridge NickName Field
           as defined in RFC 6325 section 3.7 to be transmitted." 
       REFERENCE "RFC 7455 and RFC6325 section 3.7"
       ::= { trillOamMepEntry 15 }

   trillOamMepTxPtmHC OBJECT-TYPE
       SYNTAX          Unsigned32 (1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Hop Count field to be transmitted."
 

Kumar et al.           Expires February 24, 2016               [Page 15]
Internet Draft               TRILL OAM MIB               August 23, 2015

       REFERENCE "RFC 7455 section 3" 
       ::= { trillOamMepEntry 16 }

   trillOamMepTxPtmReplyModeOob OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "True Indicates that Reply of Ptm will be made out of
            band and out of band IP Address TLV is to be 
            transmitted. False indicates that In band reply 
            is transmitted."
       REFERENCE "RFC 7455 section 10"
       DEFVAL          { false }
       ::= { trillOamMepEntry 17 }

   trillOamMepTransmitPtmReplyIp OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (4..16))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "IP address for out of band IP Address TLV is to be
            Transmitted.  The  maximum length for IPv6
            address  is 16 Octets.  The maximum length
            for an  IPv4 address is 4 octets."
       REFERENCE "RFC 7455 section 3 and 10" 
       ::= { trillOamMepEntry 18 }

   trillOamMepTxPtmFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "96 Byte Flow Entropy as defined in RFC 7455 to be 
            transmitted."
       REFERENCE "RFC 7455 section 3" 
       ::= { trillOamMepEntry 19 }

   trillOamMepTxPtmStatus OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "A Boolean flag set to true by the MEP Path Trace 
            Initiator State
           Machine or an MIB manager to indicate that another 
           PTM is being transmitted. 
           This is Reset to false by the MEP Initiator 
 

Kumar et al.           Expires February 24, 2016               [Page 16]
Internet Draft               TRILL OAM MIB               August 23, 2015

           State Machine.
           The PTM managed objects in the MEP table are used 
           in a manner similar to that described for LBM 
           transmission in dot1agCfmMepTable. As per RFC7455 
           section 10, Operation of the Path Trace Message is
           identical to the Loopback Message except that it is 
           first transmitted with a TRILL Header Hop count 
           field value of 1 and then retransmitted with 
           incrementing Hop count until a response is received 
           from the destination RBridge, or the Hop Count 
           reaches a configured maximum value. 
           trillOamMepTxPtmStatus Status is reset to FALSE 
           by initiator when last PTM is transmitted."
       REFERENCE "RFC 7455 section 10"
       DEFVAL          { false } 
       ::= { trillOamMepEntry 20 }

   trillOamMepTxPtmResultOK OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "Indicates the following results of the operation:
           - true  The Path Trace Message(s) will be (or has been) 
             sent.
           - false The Path Trace Message(s) will not be sent."
       REFERENCE "RFC 7455 section 10"
       DEFVAL          { true }
       ::= { trillOamMepEntry 21 }

   trillOamMepTxPtmSeqNumber OBJECT-TYPE
       SYNTAX          Unsigned32
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Path Trace Transaction Identifier of the first 
            PTM (to be) sent. The value returned is 
            undefined if trillOamMepTxPtmResultOK is false."
       REFERENCE "RFC 7455 section 10" 
       ::= { trillOamMepEntry 22 }

   trillOamMepTxPtmMessages OBJECT-TYPE
       SYNTAX          Integer32 (1..1024)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The number of Path Trace messages to be transmitted.
            As per RFC section 10 first Path Trace Messages
 

Kumar et al.           Expires February 24, 2016               [Page 17]
Internet Draft               TRILL OAM MIB               August 23, 2015

            is transmitted with Hop count 1 and An RBridge may 
            continue to retransmit the request at periodic
            interval until response is received from destination
            Rbridge, or the Hop Count reaches a configured 
            maximum value. The event of the Destination
            response being received or the  Hop count reaching
            its maximum is treated  as single Counter 
            increment of this object, and above process is 
            repeated starting 
            Hop count 1 till maximum PTM transmission 
            is reached. It's treated as Repeat Counter for
            above described operation."
       REFERENCE "RFC 7455 section 10" 
       ::= { trillOamMepEntry 23 }

   trillOamMepTxMtvmTree OBJECT-TYPE
       SYNTAX          Unsigned32
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Multi-destination Tree is identifier for tree as 
            defined in RFC6325." 
       ::= { trillOamMepEntry 24 }

   trillOamMepTxMtvmHC OBJECT-TYPE
       SYNTAX          Unsigned32(1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Hop Count field to be transmitted.
           " 
       REFERENCE "RFC 7455 section 3, RFC 6325 section 3"
       ::= { trillOamMepEntry 25 }

   trillOamMepTxMtvmReplyModeOob OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "A True Indicates that Reply of Mtvm is out of band and
           out of band IP Address TLV is to be transmitted. 
           A False indicates that In band reply is transmitted."
       REFERENCE "RFC 7455 section 11" 
       ::= { trillOamMepEntry 26 }

   trillOamMepTransmitMtvmReplyIp OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (4..16))
       MAX-ACCESS      read-create
 

Kumar et al.           Expires February 24, 2016               [Page 18]
Internet Draft               TRILL OAM MIB               August 23, 2015

       STATUS          current
       DESCRIPTION
           "IP address for out of band IP Address TLV is to be 
            transmitted. The Maximum length for IPv6 is 16 OCTET
            and IPv4 is 4 OCTET."
       REFERENCE "RFC 7455 section 11" 
       ::= { trillOamMepEntry 27 }

   trillOamMepTxMtvmFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "96 Byte Flow Entropy as defined in RFC 7455 to be 
            transmitted."
       REFERENCE "RFC 7455 section 3" 
       ::= { trillOamMepEntry 28 }

   trillOamMepTxMtvmStatus OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "A Boolean flag set to true by the MEP Multi Destination 
            Initiator State Machine or an MIB manager to indicate 
            that another Mtvm is being transmitted. 
           Reset to false by the MEP Initiator State Machine.
           The Mtvm managed objects in the MEP table are used 
           in a manner similar to that described for LBM 
           transmission in dot1agCfmMepTable. As per RFC7455 
           section 11, Operation of the MTvm Message is
           identical to the Loopback Message except that it is 
           first transmitted with a TRILL Header Hop count 
           field value of 1 and it is retransmitted incrementing
           Hop count until a response is received from the 
           destination RBridge, or the Hop Count reaches a
           configured maximum value. trillOamMepTxMtvmStatus 
           Status is reset to FALSE by initiator when last Mtvm 
           is transmitted."
       REFERENCE "RFC 7455 section 11"
       DEFVAL          { false } 
       ::= { trillOamMepEntry 29 }

   trillOamMepTxMtvmResultOK OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
 

Kumar et al.           Expires February 24, 2016               [Page 19]
Internet Draft               TRILL OAM MIB               August 23, 2015

           "Indicates the result of the operation in 
            the following way:
           - true  The Multi-destination Message(s) will be 
             (or has been) sent.
           - false The Multi-destination Message(s) will not be sent."
       REFERENCE "RFC 7455 section 11"
       DEFVAL          { true } 
       ::= { trillOamMepEntry 30 }

   trillOamMepTxMtvmMessages OBJECT-TYPE
       SYNTAX          Integer32 (1..1024)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The number of Multi Destination messages to be transmitted.
            Rbridge retransmit the Multi Destination message 
            incrementing the session Identification Number at periodic
            interval until either retransmission count expires."
       REFERENCE "RFC 7455 section 11" 
       ::= { trillOamMepEntry 31 }

   trillOamMepTxMtvmSeqNumber OBJECT-TYPE
       SYNTAX          Unsigned32
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Multi-destination Transaction Identifier of the 
            first MTVM (to be)
           sent. The value returned is undefined if 
           trillOamMepTxMtvmResultOK is false."
       REFERENCE "RFC 7455 section 11" 
       ::= { trillOamMepEntry 32 }

   trillOamMepTxMtvmScopeList OBJECT-TYPE
       SYNTAX          OCTET STRING
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Multi-destination Rbridge Scope list which
              requires 2 octets per Rbridge."
       REFERENCE "RFC 7455 section 11" 
       ::= { trillOamMepEntry 33 }

   trillOamMepDiscontinuityTime OBJECT-TYPE
       SYNTAX          TimeStamp
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
 

Kumar et al.           Expires February 24, 2016               [Page 20]
Internet Draft               TRILL OAM MIB               August 23, 2015

           "Snapshot of the value of the sysUpTime object at the
            beginning of the latest period of continuity of the
            statistical counters associated with this MEP." 
       ::= { trillOamMepEntry 34 }

   -- *****************************************************************
   -- TRILL OAM Tx Measurement Configuration Table
   -- *****************************************************************

   trillOamMepFlowCfgTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamMepFlowCfgEntry 
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table includes configuration objects and operations
            for the Trill OAM RFC 7455.

            Each row in the table represents a Flow configuration
            Entry for  the defined MEP. This table uses four indices.
            The first  three indices are the indices of the Maintenance
            Domain, MaNet, and MEP tables. The fourth index is the
            specific flow configuration Entry on the selected MEP.

           Some writable objects in this table are only applicable in 
           certain cases (as described under each object), and 
           attempts to write values for them in other cases 
           will be ignored."
       REFERENCE       "RFC 7455"
       ::= { trillOamMep 2 }

   trillOamMepFlowCfgEntry OBJECT-TYPE
       SYNTAX          TrillOamMepFlowCfgEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "The conceptual row of trillOamMepFlowCfgTable."
       INDEX           {
                           dot1agCfmMdIndex,
                           dot1agCfmMaIndex,
                           dot1agCfmMepIdentifier,
                           trillOamMepFlowCfgIndex
                       } 
       ::= { trillOamMepFlowCfgTable 1 }

   TrillOamMepFlowCfgEntry ::= SEQUENCE {
           trillOamMepFlowCfgIndex       Unsigned32,
           trillOamMepFlowCfgFlowEntropy OCTET STRING,
 

Kumar et al.           Expires February 24, 2016               [Page 21]
Internet Draft               TRILL OAM MIB               August 23, 2015

           trillOamMepFlowCfgDestRName   Unsigned32,
           trillOamMepFlowCfgFlowHC      Unsigned32,
           trillOamMepFlowCfgRowStatus   RowStatus
           }

   trillOamMepFlowCfgIndex OBJECT-TYPE
       SYNTAX          Unsigned32 (1..65535)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "An index to the Trill OAM MEP Flow Configuration table which
           indicates the specific Flow for the MEP.

           The index is never reused for other flow sessions on the 
           same 
           MEP while this session is active.  The index value keeps 
           increasing until it wraps to 0. This value can also be 
           used in Flow-identifier TLV RFC 7455."
       REFERENCE "RFC 7455" 
       ::= { trillOamMepFlowCfgEntry 1 }

   trillOamMepFlowCfgFlowEntropy OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (96))
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "This is 96 byte of Flow Entropy as described in
           TRILL OAM RFC 7455." 
       REFERENCE "RFC 7455 section 3"
       ::= { trillOamMepFlowCfgEntry 2 }

   trillOamMepFlowCfgDestRName OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65471)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Target Destination Rbridge NickName Field as
           defined in RFC 6325 section 3.7 to be transmitted."
       REFERENCE "RFC 7455 section 3 and RFC 6325 section 3.7" 
       ::= { trillOamMepFlowCfgEntry 3 }

   trillOamMepFlowCfgFlowHC OBJECT-TYPE
       SYNTAX          Unsigned32 (1..63)
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The Time to Live field to be transmitted.
           to be transmitted." 
 

Kumar et al.           Expires February 24, 2016               [Page 22]
Internet Draft               TRILL OAM MIB               August 23, 2015

       REFERENCE "RFC 7455 section 3 and RFC 6325 section 3.7"
       ::= { trillOamMepFlowCfgEntry 4 }

   trillOamMepFlowCfgRowStatus OBJECT-TYPE
       SYNTAX          RowStatus
       MAX-ACCESS      read-create
       STATUS          current
       DESCRIPTION
           "The status of the row.

           The writable columns in a row cannot be changed if the row
           is active. All columns MUST have a valid value before a row
           can be activated."
       ::= { trillOamMepFlowCfgEntry 5 }

   -- ******************************************************************
   -- TRILL OAM Path Trace Reply Table
   -- ******************************************************************

   trillOamPtrTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamPtrEntry 
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table includes Path Trace Reply objects and 
            operations for the Trill OAM RFC 7455. 

           Each row in the table represents a Path Trace Reply Entry for
           the defined MEP and Transaction. 
            This table uses four indices. 
           The first three indices are the indices of the 
           Maintenance Domain, 
           MaNet, and MEP tables. The fourth index is the specific 
           Transaction Identifier on the selected MEP.

           Some writable objects in this table are only applicable in 
           certain cases (as described under each object), 
           and attempts to
           write values for them in other cases will be ignored."
       REFERENCE       "RFC 7455"
       ::= { trillOamMep 3 }

   trillOamPtrEntry OBJECT-TYPE
       SYNTAX          TrillOamPtrEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
 

Kumar et al.           Expires February 24, 2016               [Page 23]
Internet Draft               TRILL OAM MIB               August 23, 2015

           "The conceptual row of trillOamPtrTable."
       INDEX           {
                           dot1agCfmMdIndex,
                           dot1agCfmMaIndex,
                           dot1agCfmMepIdentifier,
                           trillOamMepPtrTransactionId
                       } 
       ::= { trillOamPtrTable 1 }

   TrillOamPtrEntry ::= SEQUENCE {
           trillOamMepPtrTransactionId           Unsigned32,
           trillOamMepPtrHC                      Unsigned32,
           trillOamMepPtrFlag                    Unsigned32,
           trillOamMepPtrErrorCode               Unsigned32,
           trillOamMepPtrTerminalMep             TruthValue,
           trillOamMepPtrLastEgressId            Unsigned32,
           trillOamMepPtrIngress       Dot1agCfmIngressActionFieldValue,
           trillOamMepPtrIngressMac              MacAddress,
           trillOamMepPtrIngressPortIdSubtype    LldpPortIdSubtype,
           trillOamMepPtrIngressPortId           LldpPortId,
           trillOamMepPtrEgress        Dot1agCfmEgressActionFieldValue,
           trillOamMepPtrEgressMac               MacAddress,
           trillOamMepPtrEgressPortIdSubtype     LldpPortIdSubtype,
           trillOamMepPtrEgressPortId            LldpPortId,
           trillOamMepPtrChassisIdSubtype        LldpChassisIdSubtype,
           trillOamMepPtrChassisId               LldpChassisId,
           trillOamMepPtrOrganizationSpecificTlv OCTET STRING,
           trillOamMepPtrNextHopNicknames        OCTET STRING
   }

   trillOamMepPtrTransactionId OBJECT-TYPE
       SYNTAX          Unsigned32 (0..4294967295)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "Transaction identifier/sequence number returned by a 
            previous transmit path trace message command, 
            indicating which PTM's response is going to be returned."
       REFERENCE       "RFC 7455 section 10" 
       ::= { trillOamPtrEntry 1 }

   trillOamMepPtrHC  OBJECT-TYPE
       SYNTAX          Unsigned32 (1..63)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Hop Count field value for a returned PTR."
       REFERENCE       "RFC 7455" 
 

Kumar et al.           Expires February 24, 2016               [Page 24]
Internet Draft               TRILL OAM MIB               August 23, 2015

       ::= { trillOamPtrEntry 2 }

   trillOamMepPtrFlag OBJECT-TYPE
       SYNTAX          Unsigned32 (0..15)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "FCOI (TRILL OAM Message TLV) field value for a 
            returned PTR."
       REFERENCE       "RFC 7455, 8.4.3" 
       ::= { trillOamPtrEntry 3 }

   trillOamMepPtrErrorCode OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Return Code and Return Sub code value for a returned PTR."
       REFERENCE       "RFC 7455, 8.4.3" 
       ::= { trillOamPtrEntry 4 }

   trillOamMepPtrTerminalMep OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "A boolean value stating whether the forwarded PTM reached a
           MEP enclosing its MA, as returned in the Terminal MEP flag of
           the Flags field."
       REFERENCE       "RFC 7455" 
       ::= { trillOamPtrEntry 5 }

   trillOamMepPtrLastEgressId OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "An Integer field holding the Last Egress Identifier returned
           in the PTR Upstream Rbridge nickname TLV of the PTR.
           The Last Egress Identifier identifies the Upstream Nickname."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 6 }

   trillOamMepPtrIngress OBJECT-TYPE
       SYNTAX          Dot1agCfmIngressActionFieldValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
 

Kumar et al.           Expires February 24, 2016               [Page 25]
Internet Draft               TRILL OAM MIB               August 23, 2015

           "The value returned in the Ingress Action Field of the PTR.
           The value ingNoTlv(0) indicates that no Reply Ingress TLV was
           returned in the PTM."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 7 }

   trillOamMepPtrIngressMac OBJECT-TYPE
       SYNTAX          MacAddress
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the ingress MAC address field."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 8 }

   trillOamMepPtrIngressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrIngressPortIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 9 }

   trillOamMepPtrIngressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrIngressPortId object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 10 }

   trillOamMepPtrEgress OBJECT-TYPE
       SYNTAX          Dot1agCfmEgressActionFieldValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The value returned in the Egress Action Field of the PTR.
           The value ingNoTlv(0) indicates that no Reply Egress TLV was
           returned in the PTM."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 11 }

   trillOamMepPtrEgressMac OBJECT-TYPE
       SYNTAX          MacAddress
 

Kumar et al.           Expires February 24, 2016               [Page 26]
Internet Draft               TRILL OAM MIB               August 23, 2015

       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the egress MAC address field."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 12 }

   trillOamMepPtrEgressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrEgressPortIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 13 }

   trillOamMepPtrEgressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepPtrEgressPortId object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 14 }

   trillOamMepPtrChassisIdSubtype OBJECT-TYPE
       SYNTAX          LldpChassisIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "This object specifies the format of the Chassis ID returned
           in the Sender ID TLV of the PTR, if any.  This value is
           meaningless if the trillOamMepPtrChassisId 
           has a length of 0."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 15 }

   trillOamMepPtrChassisId OBJECT-TYPE
       SYNTAX          LldpChassisId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The Chassis ID returned in the Sender ID TLV of the PTR, if
           any. The format of this object is determined by the
           value of the trillOamMepPtrChassisIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1" 
 

Kumar et al.           Expires February 24, 2016               [Page 27]
Internet Draft               TRILL OAM MIB               August 23, 2015

       ::= { trillOamPtrEntry 16 }

   trillOamMepPtrOrganizationSpecificTlv OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "All Organization specific TLVs returned in the PTR, if
           any.  Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 17 }

   trillOamMepPtrNextHopNicknames OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next hop Rbridge List TLV returned in the PTR, if
           any.  Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamPtrEntry 18 }

   -- ******************************************************************
   -- TRILL OAM Multi Destination Reply Table
   -- ******************************************************************

   trillOamMtvrTable OBJECT-TYPE
       SYNTAX          SEQUENCE OF TrillOamMtvrEntry 
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "This table includes Multi-destination Reply objects and 
            operations for the Trill OAM RFC 7455. 

           Each row in the table represents a Multi-destination Reply 
           Entry for the defined MEP and Transaction. 
           This table uses five indices. 
           The first three indices are the indices of the 
           Maintenance Domain, 
           MaNet, and MEP tables. The fourth index is the specific 
           Transaction Identifier on the selected MEP.
           The fifth index is the receive order of Multi-destination
           replies.

           Some writable objects in this table are only applicable in 
 

Kumar et al.           Expires February 24, 2016               [Page 28]
Internet Draft               TRILL OAM MIB               August 23, 2015

           certain cases (as described under each object), 
           and attempts to
           write values for them in other cases will be ignored."
       REFERENCE       "RFC 7455"
       ::= { trillOamMep 4 }

   trillOamMtvrEntry OBJECT-TYPE
       SYNTAX          TrillOamMtvrEntry
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "The conceptual row of trillOamMtvrTable."
       INDEX           {
                           dot1agCfmMdIndex,
                           dot1agCfmMaIndex,
                           dot1agCfmMepIdentifier,
                           trillOamMepPtrTransactionId,
                           trillOamMepMtvrReceiveOrder
                       } 
       ::= { trillOamMtvrTable 1 }

   TrillOamMtvrEntry ::= SEQUENCE {
           trillOamMepMtvrTransactionId           Unsigned32,
           trillOamMepMtvrReceiveOrder            Unsigned32,
           trillOamMepMtvrFlag                    Unsigned32,
           trillOamMepMtvrErrorCode               Unsigned32,
           trillOamMepMtvrLastEgressId            Unsigned32,
           trillOamMepMtvrIngress    Dot1agCfmIngressActionFieldValue,
           trillOamMepMtvrIngressMac              MacAddress,
           trillOamMepMtvrIngressPortIdSubtype    LldpPortIdSubtype,
           trillOamMepMtvrIngressPortId           LldpPortId,
           trillOamMepMtvrEgress     Dot1agCfmEgressActionFieldValue,
           trillOamMepMtvrEgressMac               MacAddress,
           trillOamMepMtvrEgressPortIdSubtype     LldpPortIdSubtype,
           trillOamMepMtvrEgressPortId            LldpPortId,
           trillOamMepMtvrChassisIdSubtype        LldpChassisIdSubtype,
           trillOamMepMtvrChassisId               LldpChassisId,
           trillOamMepMtvrOrganizationSpecificTlv OCTET STRING,
           trillOamMepMtvrNextHopNicknames        OCTET STRING,
           trillOamMepMtvrReceiverAvailability    TruthValue,
           trillOamMepMtvrReceiverCount           TruthValue
   }

   trillOamMepMtvrTransactionId OBJECT-TYPE
       SYNTAX          Unsigned32 (0..4294967295)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
 

Kumar et al.           Expires February 24, 2016               [Page 29]
Internet Draft               TRILL OAM MIB               August 23, 2015

           "Transaction identifier/sequence number returned by a
            previous
           transmit Multi-destination message command, indicating 
           which MTVM's response is going to be returned."
       REFERENCE       "RFC 7455 section 11" 
       ::= { trillOamMtvrEntry 1 }

   trillOamMepMtvrReceiveOrder OBJECT-TYPE
       SYNTAX          Unsigned32 (1..4294967295)
       MAX-ACCESS      not-accessible
       STATUS          current
       DESCRIPTION
           "An index to distinguish among multiple MTVR with same
            MTVR Transaction Identifier field value. 
            trillOamMepMtvrReceiveOrder are assigned sequentially 
            from 1,
            in the order that the Multi-destination Tree Initiator
            received the MTVRs." 
       REFERENCE   "RFC 7455 section 11"
       ::= { trillOamMtvrEntry 2 }

   trillOamMepMtvrFlag OBJECT-TYPE
       SYNTAX          Unsigned32 (0..15)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "FCOI (TRILL OAM Message TLV) field value for a 
            returned MTVR."
       REFERENCE       "RFC 7455, 8.4.2" 
       ::= { trillOamMtvrEntry 3 }

   trillOamMepMtvrErrorCode OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Return Code and Return Sub code value for a returned MTVR."
       REFERENCE       "RFC 7455, 8.4.2" 
       ::= { trillOamMtvrEntry 4 }

   trillOamMepMtvrLastEgressId OBJECT-TYPE
       SYNTAX          Unsigned32 (0..65535)
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "An Integer field holding the Last Egress Identifier 
            returned in the MTVR Upstream Rbridge Nickname TLV 
            of the MTVR.
 

Kumar et al.           Expires February 24, 2016               [Page 30]
Internet Draft               TRILL OAM MIB               August 23, 2015

           The Last Egress Identifier identifies the 
           Upstream Nickname."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 5 }

   trillOamMepMtvrIngress OBJECT-TYPE
       SYNTAX          Dot1agCfmIngressActionFieldValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The value returned in the Ingress Action Field of 
           the MTVR.
           The value ingNoTlv(0) indicates that no 
           Reply Ingress TLV was returned in the MTVM."
       REFERENCE       "RFC 7455 11.2.3" 
       ::= { trillOamMtvrEntry 6 }

   trillOamMepMtvrIngressMac OBJECT-TYPE
       SYNTAX          MacAddress
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the ingress MAC address field."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 7 }

   trillOamMepMtvrIngressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is 
            determined by
           the value of the trillOamMepMtvrIngressPortIdSubtype 
           object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 8 }

   trillOamMepMtvrIngressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Ingress Port ID. The format of this object is determined by
           the value of the trillOamMepMtvrIngressPortId object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 9 }

 

Kumar et al.           Expires February 24, 2016               [Page 31]
Internet Draft               TRILL OAM MIB               August 23, 2015

   trillOamMepMtvrEgress OBJECT-TYPE
       SYNTAX          Dot1agCfmEgressActionFieldValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The value returned in the Egress Action Field of the MTVR.
           The value ingNoTlv(0) indicates that no Reply Egress TLV was
           returned in the MTVR."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 10 }

   trillOamMepMtvrEgressMac OBJECT-TYPE
       SYNTAX          MacAddress
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "MAC address returned in the egress MAC address field."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 11 }

   trillOamMepMtvrEgressPortIdSubtype OBJECT-TYPE
       SYNTAX          LldpPortIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepMtvrEgressPortIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 12 }

   trillOamMepMtvrEgressPortId OBJECT-TYPE
       SYNTAX          LldpPortId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Egress Port ID. The format of this object is determined by
           the value of the trillOamMepMtvrEgressPortId object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 13 }

   trillOamMepMtvrChassisIdSubtype OBJECT-TYPE
       SYNTAX          LldpChassisIdSubtype
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "This object specifies the format of the Chassis ID returned
           in the Sender ID TLV of the MTVR, if any.  This value is
           meaningless if the trillOamMepMtvrChassisId has a 
 

Kumar et al.           Expires February 24, 2016               [Page 32]
Internet Draft               TRILL OAM MIB               August 23, 2015

           length of 0."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 14 }

   trillOamMepMtvrChassisId OBJECT-TYPE
       SYNTAX          LldpChassisId
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "The Chassis ID returned in the Sender ID TLV of the MTVR, if
           any. The format of this object is determined by the
           value of the trillOamMepMtvrChassisIdSubtype object."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 15 }

   trillOamMepMtvrOrganizationSpecificTlv OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "All Organization specific TLVs returned in the MTVR, if
           any.  Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.1" 
       ::= { trillOamMtvrEntry 16 }

   trillOamMepMtvrNextHopNicknames OBJECT-TYPE
       SYNTAX          OCTET STRING (SIZE  (0 | 4..1500))
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Next hop Rbridge List TLV returned in the PTR, if
           any.  Includes all octets including and following the TLV
           Length field of each TLV, concatenated together."
       REFERENCE       "RFC 7455 8.4.3" 
       ::= { trillOamMtvrEntry 17 }

   trillOamMepMtvrReceiverAvailability OBJECT-TYPE
       SYNTAX          TruthValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "True value indicates that MTVR response contained
           Multicast receiver availability TLV."
       REFERENCE       "RFC 7455 8.4.10" 
       ::= { trillOamMtvrEntry 18 }

   trillOamMepMtvrReceiverCount OBJECT-TYPE
 

Kumar et al.           Expires February 24, 2016               [Page 33]
Internet Draft               TRILL OAM MIB               August 23, 2015

       SYNTAX          TruthValue
       MAX-ACCESS      read-only
       STATUS          current
       DESCRIPTION
           "Indicates the number of Multicast receivers available on
           responding RBridge on the VLAN specified by the 
           diagnostic VLAN."
       REFERENCE       "RFC 7455 8.4.10" 
       ::= { trillOamMtvrEntry 19 }

   -- *****************************************************************
   -- TRILL OAM MEP Database Table
   -- *****************************************************************

   trillOamMepDbTable OBJECT-TYPE
       SYNTAX      SEQUENCE OF TrillOamMepDbEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "This table is an extension of the dot1agCfmMepDbTable 
           and rows
           are automatically added to or deleted from this table based 
           upon row creation and destruction of the 
           dot1agCfmMepDbTable."
       REFERENCE
          "RFC 7455"
       ::= { trillOamMep 5 }

   trillOamMepDbEntry OBJECT-TYPE
       SYNTAX      TrillOamMepDbEntry
       MAX-ACCESS  not-accessible
       STATUS      current
       DESCRIPTION
          "The conceptual row of trillOamMepDbTable."
       AUGMENTS {
                dot1agCfmMepDbEntry
                }
       ::= { trillOamMepDbTable 1 }

   TrillOamMepDbEntry ::= SEQUENCE {
         trillOamMepDbFlowIndex         Unsigned32,
         trillOamMepDbFlowEntropy       OCTET STRING,
         trillOamMepDbFlowState         Dot1agCfmRemoteMepState,
         trillOamMepDbFlowFailedOkTime  TimeStamp,
         trillOamMepDbRbridgeName       Unsigned32,
         trillOamMepDbLastGoodSeqNum    Counter32
       }

 

Kumar et al.           Expires February 24, 2016               [Page 34]
Internet Draft               TRILL OAM MIB               August 23, 2015

   trillOamMepDbFlowIndex OBJECT-TYPE
       SYNTAX        Unsigned32 (1..65535)
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
         "This object identifies the Flow. If Flow Identifier TLV 
          is received
          than index received can also be used."
       REFERENCE "RFC 7455"
       ::= {trillOamMepDbEntry 1 }

   trillOamMepDbFlowEntropy OBJECT-TYPE
       SYNTAX        OCTET STRING (SIZE  (96))
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
         "96 byte Flow Entropy."
       REFERENCE "RFC 7455 section 3."
       ::= {trillOamMepDbEntry 2 }

   trillOamMepDbFlowState OBJECT-TYPE
       SYNTAX       Dot1agCfmRemoteMepState
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           "The operational state of the remote MEP (flow based) 
            IFF State machines. State Machine is running now per
            flow."
       REFERENCE "RFC 7455"
       ::= {trillOamMepDbEntry 3 }

    trillOamMepDbFlowFailedOkTime OBJECT-TYPE
       SYNTAX        TimeStamp
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
           "The Time (sysUpTime) at which the Remote MEP Flow state
            machine last entered either the RMEP_FAILED or RMEP_OK
            state."
       REFERENCE "RFC 7455"
       ::= {trillOamMepDbEntry 4 }

   trillOamMepDbRbridgeName OBJECT-TYPE
       SYNTAX        Unsigned32(0..65471)
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION 
            "Remote MEP Rbridge Nickname."
 

Kumar et al.           Expires February 24, 2016               [Page 35]
Internet Draft               TRILL OAM MIB               August 23, 2015

       REFERENCE "RFC 7455 RFC 6325 section 3"
       ::= {trillOamMepDbEntry 5 }

   trillOamMepDbLastGoodSeqNum OBJECT-TYPE
       SYNTAX        Counter32
       MAX-ACCESS    read-only
       STATUS        current
       DESCRIPTION
            "Last Sequence Number received."
       REFERENCE "RFC 7455 13.1"
       ::= {trillOamMepDbEntry 6}

   -- ******************************************************************
   -- TRILL OAM MIB NOTIFICATIONS (TRAPS)
   -- This notification is sent to management entity whenever a 
   -- MEP loses/restores
   -- contact with its peer Flow Meps
   -- ******************************************************************
   trillOamFaultAlarm NOTIFICATION-TYPE
       OBJECTS         { trillOamMepDbFlowState }
       STATUS          current
       DESCRIPTION
           "A MEP Flow has a persistent defect condition. 
            A notification (fault alarm) is sent to the management 
            entity with the OID of the Flow that has detected the fault.

           The management entity receiving the notification can identify
           the system from the network source address of the
           notification, and can identify the Flow reporting the defect
           by the indices in the OID of the 
           trillOamMepFlowIndex, and trillOamFlowDefect
           variable in the notification:

              dot1agCfmMdIndex - Also the index of the MEP's
                                 Maintenance Domain table entry
                                 (dot1agCfmMdTable).
              dot1agCfmMaIndex - Also an index (with the MD table index)
                                 of the MEP's Maintenance Association
                                 network table entry
                                 (dot1agCfmMaNetTable), and (with the MD
                                 table index and component ID) of the
                                 MEP's MA component table entry
                                 (dot1agCfmMaCompTable).
              dot1agCfmMepIdentifier - MEP Identifier and final index
                                 into the MEP table (dot1agCfmMepTable).
              trillOamMepFlowCfgIndex - Index identifies 
                               indicates the specific Flow for 
                               the MEP"            
 

Kumar et al.           Expires February 24, 2016               [Page 36]
Internet Draft               TRILL OAM MIB               August 23, 2015

       REFERENCE       "RFC 7455"
      ::= { trillOamNotifications 1 }

   -- ******************************************************************
   -- TRILL OAM MIB Module - Conformance Information
   -- ******************************************************************

   trillOamMibCompliances  OBJECT IDENTIFIER
       ::= { trillOamMibConformance 1 }

   trillOamMibGroups  OBJECT IDENTIFIER
       ::= { trillOamMibConformance 2 }

   -- ******************************************************************
   -- TRILL OAM MIB Units of conformance
   -- ******************************************************************

   trillOamMepMandatoryGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepRName,
                           trillOamMepNextPtmTId,
                           trillOamMepNextMtvmTId,
                           trillOamMepPtrIn,
                           trillOamMepPtrInOutofOrder,
                           trillOamMepPtrOut,
                           trillOamMepMtvrIn,
                           trillOamMepMtvrInOutofOrder,
                           trillOamMepMtvrOut,
                           trillOamMepTxLbmDestRName,
                           trillOamMepTxLbmHC,
                           trillOamMepTxLbmReplyModeOob,
                           trillOamMepTransmitLbmReplyIp,
                           trillOamMepTxLbmFlowEntropy,
                           trillOamMepTxPtmDestRName,
                           trillOamMepTxPtmHC,
                           trillOamMepTxPtmReplyModeOob,
                           trillOamMepTransmitPtmReplyIp,
                           trillOamMepTxPtmFlowEntropy,
                           trillOamMepTxPtmStatus,
                           trillOamMepTxPtmResultOK,
                           trillOamMepTxPtmMessages,
                           trillOamMepTxPtmSeqNumber,
                           trillOamMepTxMtvmTree,
                           trillOamMepTxMtvmHC,
                           trillOamMepTxMtvmReplyModeOob,
                           trillOamMepTransmitMtvmReplyIp,
                           trillOamMepTxMtvmFlowEntropy,
 

Kumar et al.           Expires February 24, 2016               [Page 37]
Internet Draft               TRILL OAM MIB               August 23, 2015

                           trillOamMepTxMtvmStatus,
                           trillOamMepTxMtvmResultOK,
                           trillOamMepTxMtvmMessages,
                           trillOamMepTxMtvmSeqNumber,
                           trillOamMepTxMtvmScopeList,
                           trillOamMepDiscontinuityTime
                       }
       STATUS          current
       DESCRIPTION
           "Mandatory objects for the TRILL OAM MEP group."
       ::= { trillOamMibGroups 1 }

   trillOamMepFlowCfgTableGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepFlowCfgFlowEntropy,
                           trillOamMepFlowCfgDestRName,
                           trillOamMepFlowCfgFlowHC,
                           trillOamMepFlowCfgRowStatus
                       }
       STATUS          current
       DESCRIPTION
           "Trill OAM MEP Flow Configuration objects group."
       ::= { trillOamMibGroups 2 }

   trillOamPtrTableGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepPtrHC,
                           trillOamMepPtrFlag,
                           trillOamMepPtrErrorCode,
                           trillOamMepPtrTerminalMep,
                           trillOamMepPtrLastEgressId,
                           trillOamMepPtrIngress,
                           trillOamMepPtrIngressMac,
                           trillOamMepPtrIngressPortIdSubtype,
                           trillOamMepPtrIngressPortId,
                           trillOamMepPtrEgress,
                           trillOamMepPtrEgressMac,
                           trillOamMepPtrEgressPortIdSubtype,
                           trillOamMepPtrEgressPortId,
                           trillOamMepPtrChassisIdSubtype,
                           trillOamMepPtrChassisId,
                           trillOamMepPtrOrganizationSpecificTlv,
                           trillOamMepPtrNextHopNicknames
                       }
       STATUS          current
       DESCRIPTION
           "Trill OAM MEP PTR objects group."
       ::= { trillOamMibGroups 3 }
 

Kumar et al.           Expires February 24, 2016               [Page 38]
Internet Draft               TRILL OAM MIB               August 23, 2015

   trillOamMtvrTableGroup OBJECT-GROUP
       OBJECTS         {
                           trillOamMepMtvrFlag,
                           trillOamMepMtvrErrorCode,
                           trillOamMepMtvrLastEgressId,
                           trillOamMepMtvrIngress,
                           trillOamMepMtvrIngressMac,
                           trillOamMepMtvrIngressPortIdSubtype,
                           trillOamMepMtvrIngressPortId,
                           trillOamMepMtvrEgress,
                           trillOamMepMtvrEgressMac,
                           trillOamMepMtvrEgressPortIdSubtype,
                           trillOamMepMtvrEgressPortId,
                           trillOamMepMtvrChassisIdSubtype,
                           trillOamMepMtvrChassisId,
                           trillOamMepMtvrOrganizationSpecificTlv,
                           trillOamMepMtvrNextHopNicknames,
                           trillOamMepMtvrReceiverAvailability,
                           trillOamMepMtvrReceiverCount
                       }
       STATUS          current
       DESCRIPTION
           "Trill OAM MEP MTVR objects group."
       ::= { trillOamMibGroups 4 }

   trillOamMepDbGroup  OBJECT-GROUP
       OBJECTS   {
         trillOamMepDbFlowIndex,
         trillOamMepDbFlowEntropy,
         trillOamMepDbFlowState,
         trillOamMepDbFlowFailedOkTime,
         trillOamMepDbRbridgeName,
         trillOamMepDbLastGoodSeqNum
       }

       STATUS      current
       DESCRIPTION
          "Trill OAM MEP DB objects group."
       ::= { trillOamMibGroups 5 }

   trillOamNotificationGroup NOTIFICATION-GROUP
       NOTIFICATIONS  { trillOamFaultAlarm }
       STATUS current
       DESCRIPTION
           "A collection of objects describing notifications(traps)."
       ::= { trillOamMibGroups 6 }

   -- ******************************************************************
 

Kumar et al.           Expires February 24, 2016               [Page 39]
Internet Draft               TRILL OAM MIB               August 23, 2015

   -- TRILL OAM MIB Module Compliance statements
   -- ******************************************************************

   trillOamMibCompliance MODULE-COMPLIANCE
       STATUS          current
       DESCRIPTION
           "The compliance statement for the TRILL OAM MIB."
       MODULE          -- this module
       MANDATORY-GROUPS {
                           trillOamMepMandatoryGroup,
                           trillOamMepFlowCfgTableGroup,
                           trillOamPtrTableGroup,
                           trillOamMtvrTableGroup,
                           trillOamMepDbGroup,
                           trillOamNotificationGroup
                       }
       ::= { trillOamMibCompliances 1 }

   -- Compliance requirement for read-only implementation.

   trillOamMibReadOnlyCompliance MODULE-COMPLIANCE
       STATUS current
       DESCRIPTION
           "Compliance requirement for implementation that only
            provide read-only support for TRILL-OAM-MIB.
            Such devices can be monitored but cannot be configured
            using this MIB module."
       MODULE -- this module
       MANDATORY-GROUPS {
                           trillOamMepMandatoryGroup,
                           trillOamMepFlowCfgTableGroup,
                           trillOamPtrTableGroup,
                           trillOamMtvrTableGroup,
                           trillOamMepDbGroup,
                           trillOamNotificationGroup
                         }
       -- trillOamMepTable

       OBJECT trillOamMepTxLbmDestRName  
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxLbmHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

 

Kumar et al.           Expires February 24, 2016               [Page 40]
Internet Draft               TRILL OAM MIB               August 23, 2015

       OBJECT trillOamMepTxLbmReplyModeOob    
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTransmitLbmReplyIp
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxLbmFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmDestRName
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmReplyModeOob
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTransmitPtmReplyIp
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmStatus
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmResultOK
       MIN-ACCESS  read-only
            DESCRIPTION
 

Kumar et al.           Expires February 24, 2016               [Page 41]
Internet Draft               TRILL OAM MIB               August 23, 2015

                "Write access is not required."

       OBJECT trillOamMepTxPtmMessages
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxPtmSeqNumber
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmTree
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmReplyModeOob
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTransmitMtvmReplyIp
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmStatus
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmResultOK
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmMessages
 

Kumar et al.           Expires February 24, 2016               [Page 42]
Internet Draft               TRILL OAM MIB               August 23, 2015

       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmSeqNumber
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepTxMtvmScopeList
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

   -- trillOamMepFlowCfgTable

       OBJECT trillOamMepFlowCfgFlowEntropy
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepFlowCfgDestRName
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepFlowCfgFlowHC
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       OBJECT trillOamMepFlowCfgRowStatus
       MIN-ACCESS  read-only
            DESCRIPTION
                "Write access is not required."

       ::= { trillOamMibCompliances 2 }

   END

8. Security Considerations

   This MIB relates to a system that will provide network connectivity
 

Kumar et al.           Expires February 24, 2016               [Page 43]
Internet Draft               TRILL OAM MIB               August 23, 2015

   and packet forwarding services. As such, improper manipulation of the
   objects represented by this MIB may result in denial of service to a
   large number of end-users.

   There are number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-create. Such objects may be
   considered sensitive or vulnerable in some network environments. The
   support for SET operations in a non-secure environment without proper
   protection can have negative effect on sensitivity/vulnerability: 

   The following table and objects in the TRILL-OAM-MIB can be
   manipulated to to interfere with the operation of RBridges by causing
   cpu spike:

   o trillOamMepTransmitLbmReplyIp allows reply of Loopback message to
   be transmitted to Ip address in the TLV and thus allowing replies to
   be sent to any system or single single system to cause Denial of
   Service.

   o trillOamMepTransmitPtmReplyIp allows reply of Path Trace message to
   be transmitted to Ip address in the TLV and thus allowing replies to
   be sent to any system or single single system to cause Denial of
   Service.

   o trillOamMepTxPtmMessages allows generation of Ptm Messages and can
   be used to generate lots of cpu driven traffic.

   o trillOamMepTransmitMtvmReplyIp allows reply of Mtv message to be
   transmitted to Ip address in the TLV and thus allowing replies to be
   sent to any system or single single system to cause Denial of
   Service.

   o trillOamMepTxMtvmMessages allows generation of Mtv Messages and can
   be used to generate lots of cpu driven traffic.

   Some of the readable objects in this MIB module (i.e., objects with a
   MAX-ACCESS other than not-accessible) may be considered sensitive or
   vulnerable in some network environments. It is thus important to
   control GET and/or NOTIFY access to these objects and possibly to
   encrypt the values of these objects when sending them over the
   network via SNMP. For example, Path trace message expose unicast
   topology of network and Multi-destination Tree verification message
   expose multicast tree topology of network and this information should
   not be available to all users of the network.

   SNMP version prior to SNMPv3 did not include adequate security. Even
   if the network itself is secure(for example by using IPsec), there is
   no control as to who on the secure network is allowed to access and
 

Kumar et al.           Expires February 24, 2016               [Page 44]
Internet Draft               TRILL OAM MIB               August 23, 2015

   GET/SET (read/change/create/delete) the objects in this MIB module.

   Implementation should provide the security features described by
   SNMPv3 framework (see [RFC3410]), and implementations claiming
   compliance to the SNMPv3 standard MUST include full support for
   authentication and privacy via the User-based Security Model
   (USM)[RFC3414] with the AES cipher algorithm [RFC3826].
   Implementations MAY also provide support for the Transport Security
   Model (TSM) [RFC5591] in combination with a secure transport such as
   SSH [RFC5592] or TLS/DTLS [RFC6353]. 

   Further, deployment of SNMP version prior to SNMPv3 is NOT
   RECOMMENDED. Instead, deployment of SNMPv3 with cryptographic
   security enabled is RECOMMENDED. It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give only those
   principals (users) that have legitimate rights to indeed GET or SET
   (change/create/delete) them access to the objects.

9. IANA Considerations

   The MIB module in this document uses the following IANA-assigned
   OBJECT IDENTIFIER value recorded in the SMI Numbers registry:

   Descriptor   OBJECT   IDENTIFIER  value
   ----------------------------------------
   trillOamMIB  { mib-2 xxx }

   Editor's Note (to be removed prior to publication): the IANA is
   requested to assign a value for "xxx" under the 'mib-2' subtree and
   to record the assignment in the SMI Numbers registry. When the
   assignment has been made, the RFC Editor is asked to replace "XXX"
   (here and in the MIB module) with the assigned value and to remove
   this note.

10.  References
10.1.  Normative References

              [RFC2119] Bradner, S., "Key words for use in RFCs to
              Indicate Requirement Levels", BCP 14, RFC 2119, March
              1997.

              [RFC2578] McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Structure of Management Information
              Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
 

Kumar et al.           Expires February 24, 2016               [Page 45]
Internet Draft               TRILL OAM MIB               August 23, 2015

              [RFC2579] McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Textual Conventions for SMIv2", STD
              58, RFC 2579, April 1999.

              [RFC2580] McCloghrie, K., Ed., Perkins, D., Ed., and J.
              Schoenwaelder, Ed., "Conformance Statements for SMIv2",
              STD 58, RFC 2580, April 1999.

              [RFC6325] Perlman, R., Eastlake 3rd, D., Dutt, D., Gai,
              S., and A. Ghanwani, "Routing Bridges (RBridges): Base
              Protocol Specification", RFC 6325, July 2011. 

              [RFC7172] Eastlake 3rd, D., Zhang, M., Agarwal, P.,
              Perlman, R., and D. Dutt, "Transparent Interconnection of
              Lots of Links (TRILL): Fine-Grained Labeling", RFC 7172,
              May 2014.

              [RFC7455] Senevirathne, T., et.al., "Transparent
              Interconnection of Lots of Links (TRILL): Fault
              Management", March 2015.

              [LLDP-MIB] IEEE,
              http://www.ieee802.org/1/files/public/MIBs/LLDP-MIB-
              200505060000Z.txt

              [802.1Q] IEEE, "IEEE Standard for Local and metropolitan
              area networks - Media Access Control (MAC) Bridges and
              Virtual Bridge Local Area Networks", IEEE Std 802.1Q-2011,
              31 August 2011.

10.2.  Informative References

              [802.1Q] IEEE, "IEEE Standard for Local and metropolitan
              area networks - Media Access Control (MAC) Bridges and
              Virtual Bridge Local Area Networks", IEEE Std 802.1Q-2011,
              31 August 2011. 

              [RFC3410] Case, J., Mundy, R., Partain, D., and B.Stewart,
              "Introduction and Applicability Statements for Internet-
              Standard Management Framework", RFC 3410, December 2002.

              [RFC6905] Senevirathne, T., Bond, D., Aldrin, S., Li, Y.,
              and R. Watve, "Requirements for Operations,
              Administration, and Maintenance (OAM) in Transparent
              Interconnection of Lots of Links (TRILL)", RFC 6905, March
              2013.
 

Kumar et al.           Expires February 24, 2016               [Page 46]
Internet Draft               TRILL OAM MIB               August 23, 2015

              [RFC7174] Salam, S., Senevirathne, T., Aldrin, S., and D.
              Eastlake 3rd, "Transparent Interconnection of Lots of
              Links (TRILL) Operations, Administration, and Maintenance
              (OAM) Framework", RFC 7174, May 2014. 

11.  Acknowledgments

   We wish to thank members of the IETF TRILL WG, and mib-doctor for
   their comments and suggestions. Detailed comments were provided by
   Sam Aldrin, Donald Eastlake, Tom Taylor, and Harrie Hazewinkel. 

12. Copyright and Disclaimer
   Copyright (c) 2015 IETF Trust and the persons identified as authors
   of the code. All rights reserved. Redistribution and use in source
   and binary forms, with or without modification, is permitted pursuant
   to, and subject to the license terms contained in, the Simplified BSD
   License set forth in Section 4.c of the IETF Trust's Legal Provisions
   Relating to IETF Documents (http://trustee.ietf.org/license-info).

   Copyright (c) 2015 IETF Trust and the persons identified as authors
   of the code. All rights reserved. Redistribution and use in source
   and binary forms, with or without modification, are permitted
   provided that the following conditions are met:

      o Redistributions of source code must retain the above copyright
      notice, this list of conditions and the following disclaimer. 

      o Redistributions in binary form must reproduce the above
      copyright notice, this list of conditions and the following
      disclaimer in the documentation and/or other materials provided
      with the distribution. 

      o Neither the name of Internet Society, IETF or IETF Trust, nor
      the names of specific contributors, may be used to endorse or
      promote products derived from this software without specific prior
      written permission.

   THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
   "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
   LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
   A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
   OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
   SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
   LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
   DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
   THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
   (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
   OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 

Kumar et al.           Expires February 24, 2016               [Page 47]
Internet Draft               TRILL OAM MIB               August 23, 2015

   Authors' Addresses

      Deepak Kumar
      Cisco
      510 McCarthy Blvd,
      Milpitas, CA 95035, USA
      Phone : +1 408-853-9760
      Email: dekumar@cisco.com

      Samer Salam
      Cisco
      595 Burrard St. Suite 2123
      Vancouver, BC V7X 1J1, Canada
      Email: ssalam@cisco.com

      Tissa Senevirathne
      Consultant
      Email: tsenevir@gmail.com

Kumar et al.           Expires February 24, 2016               [Page 48]