Skip to main content

A YANG Data Model for IPv4-in-IPv6 Softwires
draft-ietf-softwire-yang-01

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8676.
Expired & archived
Authors Qi Sun , Hao Wang , Yong Cui , Ian Farrer , Sladjana Zoric , Mohamed Boucadair , Rajiv Asati
Last updated 2017-05-04 (Latest revision 2016-10-31)
Replaces draft-sun-softwire-yang
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd (None)
IESG IESG state Became RFC 8676 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-softwire-yang-01
Softwire Working Group                                            Q. Sun
Internet-Draft                                                   H. Wang
Intended status: Standards Track                                  Y. Cui
Expires: May 4, 2017                                 Tsinghua University
                                                               I. Farrer
                                                                S. Zoric
                                                     Deutsche Telekom AG
                                                            M. Boucadair
                                                                  Orange
                                                                R. Asati
                                                     Cisco Systems, Inc.
                                                        October 31, 2016

              A YANG Data Model for IPv4-in-IPv6 Softwires
                      draft-ietf-softwire-yang-01

Abstract

   This document defines a YANG data model for the configuration and
   operations (state, notification, RPC etc.) of IPv4-in-IPv6 Softwire
   Border Routers and Customer Premises Equipment.  The model covers the
   Lightweight 4over6, MAP-E and MAP-T Softwire mechanisms.

Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on May 4, 2017.

Sun, et al.                Expires May 4, 2017                  [Page 1]
Internet-Draft           YANG for A+P Softwires             October 2016

Copyright Notice

   Copyright (c) 2016 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   3
     1.2.  Tree Diagrams . . . . . . . . . . . . . . . . . . . . . .   3
     1.3.  YANG Modelling of NAT44 Functionality . . . . . . . . . .   4
   2.  Common  . . . . . . . . . . . . . . . . . . . . . . . . . . .   4
   3.  Lightweight 4over6  . . . . . . . . . . . . . . . . . . . . .   4
   4.  MAP-E and MAP-T . . . . . . . . . . . . . . . . . . . . . . .   4
   5.  Softwire YANG Tree Diagrams . . . . . . . . . . . . . . . . .   4
     5.1.  Common Tree Diagrams  . . . . . . . . . . . . . . . . . .   4
     5.2.  Lightweight 4over6 Tree Diagrams  . . . . . . . . . . . .   5
     5.3.  MAP-E and MAP-T Tree Diagrams . . . . . . . . . . . . . .   8
     5.4.  Notifications for Softwire YANG . . . . . . . . . . . . .   9
   6.  Softwire YANG Model . . . . . . . . . . . . . . . . . . . . .  10
   7.  Configuration Example for a lw4o6 Binding-Table . . . . . . .  26
     7.1.  Configuration Example for a MAP-E BR  . . . . . . . . . .  27
   8.  Security Considerations . . . . . . . . . . . . . . . . . . .  28
   9.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  29
   10. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  29
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  29
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  29
     11.2.  Informative References . . . . . . . . . . . . . . . . .  30
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  31

1.  Introduction

   The IETF Softwire Working Group has developed several IPv4-in-IPv6
   Softwire mechanisms to address various deployment contexts and
   constraints.  As a companion to the architectural specification
   documents, this document focuses on the provisioning of A+P softwire
   functional elements: Border Routers (BRs) and Customer Premises
   Equipment (CEs).

Sun, et al.                Expires May 4, 2017                  [Page 2]
Internet-Draft           YANG for A+P Softwires             October 2016

   This document defines a YANG data model [RFC6020] that can be used to
   configure and manage A+P Softwire elements using the NETCONF protocol
   [RFC6241].  A DS-Lite YANG data model is defined in
   [I-D.ietf-softwire-dslite-yang].

   The Softwire YANG model is structured into two sub-models:

   o  Lightweight 4over6 [RFC7596]

   o  MAP-E [RFC7597] and MAP-T [RFC7599] (combined due to their common
      configuration parameters).

   Two root containers are defined:

   1.  Container "softwire-config" holds the collection of YANG
       definitions common to all Softwire element configuration.

   2.  Container "softwire-state" holds YANG definitions for the
       operational state of the Softwire elements.

   A NETCONF notify module is also included.

   This approach has been taken so that the model can be easily extended
   to support additional Softwire mechanisms, if required.

1.1.  Terminology

   The reader should be familiar with the concepts and terms defined in
   [RFC7596], [RFC7597], [RFC7599], and the YANG data modelling language
   [RFC6020].

1.2.  Tree Diagrams

   The meaning of the symbols in these diagrams are as follows:

   o  Brackets "[" and "]" enclose list keys.

   o  Braces "{" and "}" enclose feature content.

   o  Parentheses "(" and ")" enclose choice and case nodes, and case
      nodes are also marked with a colon (":").

   o  Symbols after data node names: "?" means an optional node, and "*"
      denotes a list and leaf-list.

   o  Abbreviations before data node names: "rw" means configuration
      data (read-write), and "ro" means state data (read-only).

Sun, et al.                Expires May 4, 2017                  [Page 3]
Internet-Draft           YANG for A+P Softwires             October 2016

1.3.  YANG Modelling of NAT44 Functionality

   The model does not include CPE NAT-specific provisioning parameters
   that may be used for IPv4 address sharing other than the external IP
   address and port set which a softwire client may use for NAT44.  NAT-
   specific considerations are out of scope of this document.  A YANG
   model for the configuration and management of NAT gateways is
   described in [I-D.sivakumar-yang-nat].

2.  Common

   The following sections of the document are structured with the root
   of the Softwire YANG model (common to all mechanisms) described
   first.  Subsequent sections describe the models relevant to the
   different softwire mechanisms.  All functions are listed, but the
   YANG models use the "feature" statement to distinguish among the
   different softwire mechanisms.  This document defines a new module
   named "ietf-softwire" for Softwire data models such that this module
   auments "ietf-ipv6-unicast-routing" module that is defined in
   [I-D.ietf-netmod-routing-cfg].

3.  Lightweight 4over6

   Lightweight 4over6 (binding) includes two elements: lwAFTR (BR) and
   lwB4 (CE).  The lwAFTR holds configuration for IPv4-IPv6 address
   bindings which are used for the forwarding of traffic originating
   from lwB4s.

   The lwB4 is configured with the relevant parameters for establishing
   the IPv4-in-IPv6 tunnel including an IPv6 address for the lwAFTR and
   the IPv4 configuration for NAT44.

4.  MAP-E and MAP-T

   MAP-E and MAP-T elements are provisioned with the MAP rules necessary
   for defining MAP domains and forwarding rules.  For MAP-T CEs, an
   additional "ipv6-prefix" parameter is also included.  Note that when
   referring to MAP-E/T (algorithm), the CE and BR shares the same model
   for configuration and management.

5.  Softwire YANG Tree Diagrams

5.1.  Common Tree Diagrams

   Figure 1 describes the high level softwire YANG data model and the
   way tree is organized is common to all of the different softwire
   mechanisms listed in Section 1:

Sun, et al.                Expires May 4, 2017                  [Page 4]
Internet-Draft           YANG for A+P Softwires             October 2016

      +--rw softwire-config
      |  +--rw description?               string
      |  +--rw binding {binding}?
      |  |  +--rw br {br}?
      |  |  +--rw cr {cr}?
      |  +--rw algorithm {algorithm}?
      |
      +--ro softwire-state
         +--ro description?               string
         +--ro binding {binding}?
         |  +--ro br {br}?
         |  +--ro ce {ce}?
         +--ro algorithm {algorithm}?

           Figure 1: High Level Softwire YANG Tree Organization

5.2.  Lightweight 4over6 Tree Diagrams

   Figure 2 defines the softwire data model for lw4o6 (softwire binding
   mode) which includes lwAFTR (BR) and lwB4 (CE):

module: ietf-softwire
   +--rw softwire-config
   |  +--...
   |  +--rw binding {binding}?
   |     +--rw br {br}?
   |     |  +--rw enable?                          boolean
   |     |  +--rw br-instances
   |     |     +--rw br-instance* [id]
   |     |        +--rw binding-table-versioning
   |     |        |  +--rw binding-table-version?  uint64
   |     |        |  +--rw binding-table-date?     yang:date-and-time
   |     |        +--rw id                         uint32
   |     |        +--rw name?                      string
   |     |        +--rw softwire-num-threshold     uint32
   |     |        +--rw tunnel-payload-mtu         uint16
   |     |        +--rw tunnel-path-mru            uint16
   |     |        +--rw binding-table
   |     |           +--rw binding-entry* [binding-ipv6info]
   |     |              +--rw binding-ipv6info     union
   |     |              +--rw binding-ipv4-addr    inet:ipv4-address
   |     |              +--rw port-set
   |     |              |  +--rw psid-offset       uint8
   |     |              |  +--rw psid-len          uint8
   |     |              |  +--rw psid              uint16
   |     |              +--rw br-ipv6-addr         inet:ipv6-address
   |     |              +--rw lifetime?            uint32
   |     +--rw ce {ce}?

Sun, et al.                Expires May 4, 2017                  [Page 5]
Internet-Draft           YANG for A+P Softwires             October 2016

   |        +--rw enable?                          boolean
   |        +--rw ce-instances
   |           +--rw ce-instance* [binding-ipv6info]
   |              +--rw name?                      string
   |              +--rw tunnel-payload-mtu         uint16
   |              +--rw tunnel-path-mru            uint16
   |              +--rw b4-ipv6-addr-format        boolean
   |              +--rw binding-ipv6info           union
   |              +--rw binding-ipv4-addr          inet:ipv4-address
   |              +--rw port-set
   |              |  +--rw psid-offset             uint8
   |              |  +--rw psid-len                uint8
   |              |  +--rw psid                    uint16
   |              +--rw br-ipv6-addr               inet:ipv6-address
   |              +--rw lifetime?                  uint32
   +--ro softwire-state
      +--...
      +--ro binding {binding}?
         +--ro br {br}?
         |  +--ro br-instances
         |     +--ro br-instance* [id]
         |        +--ro id                         uint32
         |        +--ro name?                      string
         |        +--ro sentPacket?                yang:zero-based-counter64
         |        +--ro sentByte?                  yang:zero-based-counter64
         |        +--ro rcvdPacket?                yang:zero-based-counter64
         |        +--ro rcvdByte?                  yang:zero-based-counter64
         |        +--ro droppedPacket?             yang:zero-based-counter64
         |        +--ro droppedByte?               yang:zero-based-counter64
         |        +--ro active-softwire-num?       uint32
         |        +--ro binding-table
         |           +--ro binding-entry* [binding-ipv6info]
         |              +--ro binding-ipv6info     union
         |              +--ro active?              boolean
         +--ro ce {ce}?
            +--ro ce-instances
               +--ro ce-instance* [binding-ipv6info]
                  +--ro name?                      string
                  +--ro binding-ipv6info           union
                  +--ro sentPacket?                yang:zero-based-counter64
                  +--ro sentByte?                  yang:zero-based-counter64
                  +--ro rcvdPacket?                yang:zero-based-counter64
                  +--ro rcvdByte?                  yang:zero-based-counter64
                  +--ro droppedPacket?             yang:zero-based-counter64
                  +--ro droppedByte?               yang:zero-based-counter64

      Figure 2: Softwire Lightweight 4over6 Data Model Tree Structure

Sun, et al.                Expires May 4, 2017                  [Page 6]
Internet-Draft           YANG for A+P Softwires             October 2016

   The data model assumes that each CE/BR instance can: be enable/
   disabled, be provisioned with a dedicated configuration data, and
   maintain its own binding table.

   Additional information on some of the important lwAFTR nodes is
   provided below:

   o  binding-table-versioning: optionally used to add an incremental
      version number and/or timestamp to the binding table.  This can be
      used for logging/data retention purposes.  The version number is
      incremented and a new timestamp value written whenever a change is
      made to the contents of the binding table or a new binding table
      list is created.

   o  binding-entry: used to define the binding relationship between
      3-tuples, which contains the lwB4's IPv6 address/prefix, the
      allocated IPv4 address and restricted port-set.  For detail
      information, please refer to [RFC7596].

   o  tunnel-payload-mtu: used to set the IPv4 MTU for the lw4o6 tunnel.

   o  tunnel-path-mru: used to set the maximum lw4o6 IPv6 encapsulating
      packet size that can be received.

   o  psid-offset: used to set the number of offset bits.

   o  psid-len: defines the number of ports that will be allocated for
      the softwire.

   o  psid: used to identify the set of ports allocated for a specific
      softwire.

   o  tunnel-num-threshold: used to set the maximum number of tunnels
      that can be created on the lw4o6 device simultaneously.

   o  active-tunnel-num (ro): used to present the number of tunnels
      currently provisioned on the device.

   o  active (ro): used to show the status of particular binding-entry.

   Additional information on some of the important lwB4 nodes is
   provided below:

   o  b4-ipv6-addr-format: indicates the format of lwB4 IPv6 address.
      If set to true, the IPv6 source address of the lwB4 is constructed
      according to the description in Section 6 of [RFC7597]; if set to
      false, the lwB4 can use any valid /128 address from an assigned
      IPv6 prefix.

Sun, et al.                Expires May 4, 2017                  [Page 7]
Internet-Draft           YANG for A+P Softwires             October 2016

   o  binding-ipv6info: used to set the IPv6 address type which is
      combined in a binding entry, for a complete address or a prefix.

5.3.  MAP-E and MAP-T Tree Diagrams

   Figure 3 defines the softwire data model for MAP-E and MAP-T:

 module: ietf-softwire
    +--rw softwire-config
    |  +--...
    |  +--rw algorithm {algorithm}?
    |     +--rw enable?                        boolean
    |     +--rw algorithm
    |        +--rw algo-instance* [id]
    |           +--rw algo-versioning
    |           |  +--rw algo-version?         uint64
    |           |  +--rw algo-date?            yang:date-and-time
    |           +--rw id                       uint32
    |           +--rw name?                    string
    |           +--rw data-plane               enumeration
    |           +--rw ea-len                   uint8
    |           +--rw rule-ipv6-prefix         inet:ipv6-prefix
    |           +--rw rule-ipv4-prefix         inet:ipv4-prefix
    |           +--rw forwarding               boolean
    |           +--rw psid-offset              uint8
    |           +--rw psid-len                 uint8
    |           +--rw tunnel-payload-mtu       uint16
    |           +--rw tunnel-path-mru          uint16
    |           +--rw br-ipv6-addr             inet:ipv6-address
    |           +--rw dmr-ipv6-addr            inet:ipv6-prefix
    +--ro softwire-state
       +--...
       +--ro algorithm {algorithm}?
          +--ro algo-instances
             +--ro algo-instance* [id]
                +--ro id                       int32
                +--ro name?                    string
                +--ro sentPacket?              yang:zero-based-counter64
                +--ro sentByte?                yang:zero-based-counter64
                +--ro rcvdPacket?              yang:zero-based-counter64
                +--ro rcvdByte?                yang:zero-based-counter64
                +--ro droppedPacket?           yang:zero-based-counter64
                +--ro droppedByte?             yang:zero-based-counter64

          Figure 3: Softwire MAP-E and MAP-T Data Model Structure

   Additional information on some of the important MAP-E and MAP-T nodes
   is provided below:

Sun, et al.                Expires May 4, 2017                  [Page 8]
Internet-Draft           YANG for A+P Softwires             October 2016

   o  algo-versioning: optionally used to add a incremental version
      number and/or timestamp to the algorithm.  This can be used for
      logging/data retention purposes.  The version number is
      incremented and a new timestamp value written whenever a change is
      made to the algorithm or a new instance is created.

   o  forwarding: specifies whether the rule can be used as a Forward
      Mapping Rule (FMR).  If not set, this rule is a Basic Mapping Rule
      (BMR) only and must not be used for forwarding.  See Section 4.1
      of [RFC7598].

   o  ea-len: used to set the length of the Embedded-Address (EA), which
      defined in the mapping rule for a MAP domain.

   o  dmr-ipv6-prefix: defines the Default Mapping Rule (DMR) for MAP-T.
      This parameter is optional when configuring a MAP-T BR.

   o  stat-count (ro): use to show the numbers of packets and bytes
      information of specific device respectively.

5.4.  Notifications for Softwire YANG

   This section describes the tree structure for notifications.  These
   notifications pertain to the configuration and monitoring portions of
   the specific Softwire mechanisms.  The logic is that the softwire
   instance notifies the NETCONF client with the index for a mapping
   entry and the NETCONF client retrieves the related information from
   the operational datastore of that instance.

module: ietf-softwire
notifications:
   +---n softwire-binding-br-event {binding,br}?
   |  +--ro br-id?            -> /softwire-state/binding/br/.../id
   |  +--ro invalid-entry*    -> /softwire-config/binding/br/.../binding-table/binding-entry/binding-ipv6info
   |  +--ro added-entry*      inet:ipv6-address
   |  +--ro modified-entry*   -> /softwire-config/binding/br/.../binding-table/binding-entry/binding-ipv6info
   +---n softwire-binding-ce-event {binding,ce}?
   |  +--ro ce-binding-ipv6-addr-change    inet:ipv6-address
   +---n softwire-algorithm-instance-event {algorithm}?
      +--ro algo-id           -> /softwire-config/algorithm/.../id
      +--ro invalid-entry*    -> /softwire-config/algorithm/.../id
      +--ro added-entry*      -> /softwire-config/algorithm/.../id
      +--ro modified-entry*   -> /softwire-config/algorithm/.../id

           Figure 4: Softwire Notifications Data Model Structure

   Additional information on some of the important notification nodes is
   listed below:

Sun, et al.                Expires May 4, 2017                  [Page 9]
Internet-Draft           YANG for A+P Softwires             October 2016

   o  invalid-entry, added-entry, modified-entry: used to notify the
      client that a specific binding entry or MAP rule is expired or
      invalidated, added, or modified.

   o  ce-binding-ipv6-addr-change: used to notify that the lwB4's
      binding-ipv6-address has been changed or the value of the
      'b4-ipv6-addr-format' is "False".

6.  Softwire YANG Model

   This module imports typedefs from [RFC6991].

<CODE BEGINS> file "ietf-softwire@2016-06-04.yang"

module ietf-softwire {
  namespace "urn:ietf:params:xml:ns:yang:ietf-softwire";
  prefix "softwire";

  import ietf-inet-types {prefix inet; }
  import ietf-yang-types {prefix yang; }

  organization "Softwire Working Group";

  contact
    "
    Qi Sun <sunqi.ietf@gmail.com>
    Hao Wang <wangh13@mails.tsinghua.edu.cn>
    Yong Cui <yong@csnet1.cs.tsinghua.edu.cn>
    Ian <Farrer ian.farrer@telekom.de>
    Sladjana Zoric <sladjana.zoric@telekom.de>
    Mohamed Boucadair <mohamed.boucadair@orange.com>
    Rajiv <Asati rajiva@cisco.com>
    ";

  description
    "This document defines a YANG data model for the configuration and
    management of A+P Softwire Border Routers (BRs) and Customer
    Premises Equipment (CEs). It covers Lightweight 4over6,
    MAP-E and MAP-T mechanisms.

    Copyright (c) 2016 IETF Trust and the persons identified
    as authors of the code. All rights reserved.
    This version of this YANG module is part of RFC XXX; see the RFC
    itself for full legal notices.";

  revision 2016-06-04 {
    description
      "Version-05: Combined MAP-E/MAP-T into a single tree. Added binding

Sun, et al.                Expires May 4, 2017                 [Page 10]
Internet-Draft           YANG for A+P Softwires             October 2016

          table/alogorthm versioning";
       reference "-05";
  }

  revision 2015-09-30 {
    description
      "Version-04: Fix YANG syntax; Add flags to map-rule; Remove
      the map-rule-type element. ";
       reference "-04";
  }

  revision 2015-04-07 {
    description
      "Version-03: Integrate lw4over6; Updata state nodes; Correct
      grammar errors; Reuse groupings; Update descriptions.
      Simplify the model.";
       reference "-03";
  }

  revision 2015-02-10 {
    description
      "Version-02: Add notifications.";
       reference "-02";
  }

  revision 2015-02-06 {
    description
      "Version-01: Correct grammar errors; Reuse groupings; Update
      descriptions.";
       reference "-01";
  }

  revision 2015-02-02 {
    description
      "Initial revision.";
       reference "-00";
  }

/*
 * Features
 */

  feature binding {
    description
    "Lightweight 4over6 (binding) is an IPv4-over-IPv6 tunnelling
     transition mechanism. Lightweight 4over6 is a solution designed
     specifically for complete independence between IPv6 subnet

Sun, et al.                Expires May 4, 2017                 [Page 11]
Internet-Draft           YANG for A+P Softwires             October 2016

     prefix (and /128 IPv6 address) and IPv4 address with or
     without IPv4 address sharing.

     This is accomplished by maintaining state for
     each softwire (per-subscriber state) in the central lwAFTR and
     a hub-and-spoke forwarding architecture. In order to delegate
     the NAPT function and achieve IPv4 address sharing,
     port-restricted IPv4 addresses needs to be allocated to CEs.

     Besides lw4o6, this feature also covers MAP in 1:1 mode
     (using offset=0, PSID explicitly defined)";

   reference
      "RFC7596";
  }

  feature br {
    if-feature binding;
    description
     "The AFTR for Lightweight 4over6, so-called lwAFTR (BR). This
      feature indicates that a instance functions as a lwAFTR (BR).
      A lwAFTR (BR) is an IPv4-in-IPv6 tunnel concentrator that
      maintains per-subscriber IPv4-IPv6 address binding.";
  }

  feature ce {
    if-feature binding;
    description
      "The B4 for Lightweight 4over6, so-called lwB4 (CE). This
      feature indicates that a instance functions as a lwB4 (CE). A
      lwB4 (ce) is an IPv4-in-IPv6 tunnel initiator. It is
      dual-stack capable node, either a directly connected end-host
      or a CE. It sources IPv4 connections using the configured
      port-set and the public IPv4 address.";
  }

  feature algorithm {
    description
      "MAP-E is an IPv6 transition mechanism for transporting IPv4
      packets across an IPv6 network using IP encapsulation. MAP-E
      allows for a reduction of the amount of centralized state using
      rules to express IPv4/IPv6 address mappings. This introduces an
      algorithmic relationship between the IPv6 subnet
      and IPv4 address.
      The Mapping of Address and Port - Translation (MAP-T)
      architecture is a double stateless NAT64 based solution. It uses
      the stateless algorithmic address & transport layer port mapping
      scheme defined in MAP-E. The MAP-T solution differs from MAP-E in

Sun, et al.                Expires May 4, 2017                 [Page 12]
Internet-Draft           YANG for A+P Softwires             October 2016

      the use of IPv4-IPv6 translation, rather than encapsulation, as
      the form of IPv6 domain transport.
      This feature indicates the instance functions as a MAP-E or
      MAP-T instance.";
    reference
      "RFC7597 & RFC7599";
  }

/*
 * Grouping
 */

  grouping port-set {
    description
      "Use the PSID algorithm to represent a range of transport layer
      ports which will be used by a CE device for NAPT.";
    leaf psid-offset {
      type uint8 {
        range 0..16;
      }
      description
        "The number of offset bits. In Lightweight 4over6, the default
        value is 0 for assigning one contiguous port range. In MAP-E/T,
        the default value is 6, which excludes system ports by default
        and assigns port ranges distribute across the entire port space.
        If the this parameter is larger than 0, the value of offset
        MUST be greater than 0.";
    }
    leaf psid-len {
      type uint8 {
        range 0..15;
      }
      mandatory true;
      description
        "The length of PSID, representing the sharing ratio for an
        IPv4 address.";
    }
    leaf psid {
      type uint16;
      mandatory true;
      description
        "Port Set Identifier (PSID) value, which identifies a set
        of ports algorithmically.";
    }
  }

  grouping binding-entry {
    description

Sun, et al.                Expires May 4, 2017                 [Page 13]
Internet-Draft           YANG for A+P Softwires             October 2016

      "The lwAFTR maintains an address binding table that contains
      the binding between the lwB4's IPv6 address, the allocated IPv4
      address and restricted port-set.";
    leaf binding-ipv6info {
      type union {
        type inet:ipv6-address;
        type inet:ipv6-prefix;
      }
      mandatory true;
      description
        "The IPv6 information for a binding entry.
         If this is an IPv6 prefix, it indicates that
         the IPv6 source address of the lwB4 is constructed
         according to the description in RFC7596;
         if it is an IPv6 address, it means the lwB4 uses
         any /128 address from the assigned IPv6 prefix.
         ";
    }
    leaf binding-ipv4-addr {
      type inet:ipv4-address;
      mandatory true;
      description
        "The IPv4 address assigned to the lwB4, which is
         used as the IPv4 external address
         for lwB4 local NAPT44.";
    }
    container port-set {
      description
        "For Lightweight 4over6, the default value
        of offset should be 0, to configure one contiguous
        port range.";
      uses port-set {
        refine psid-offset {
          default "0";
        }
      }
    }
    leaf br-ipv6-addr {
      type inet:ipv6-address;
      mandatory true;
      description
        "The IPv6 address for lwaftr.";
    }
    leaf lifetime {
      type uint32;
      units seconds;
      description "The lifetime for the binding entry";
    }

Sun, et al.                Expires May 4, 2017                 [Page 14]
Internet-Draft           YANG for A+P Softwires             October 2016

  }

/*
  grouping nat-table {

    description
      "Grouping 'nat-table' is not extended. The current mechanism
      is focusing on the provisioning of external IP address and
      port set; other NAT-specific considerations are out of scope.";
  }
*/

  grouping traffic-stat {
    description "Traffic statistics";
    leaf sentPacket {
      type yang:zero-based-counter64;
      description "Number of packets sent.";
    }
    leaf sentByte {
      type yang:zero-based-counter64;
      description "Traffic sent, in bytes";
    }
    leaf rcvdPacket {
      type yang:zero-based-counter64;
      description "Number of packets received.";
    }
    leaf rcvdByte {
      type yang:zero-based-counter64;
      description "Traffic received, in bytes";
    }
    leaf droppedPacket {
      type yang:zero-based-counter64;
      description "Number of packets dropped.";
    }
    leaf droppedByte {
      type yang:zero-based-counter64;
      description "Traffic dropped, in bytes";
    }
  }

/*
 * Configuration Data Nodes
 */

  container softwire-config {
    description

Sun, et al.                Expires May 4, 2017                 [Page 15]
Internet-Draft           YANG for A+P Softwires             October 2016

      "The configuration data for Softwire instances. And the shared
      data describes the softwire data model which is common to all of
      the different softwire mechanisms, such as description.";
    leaf description {
      type string;
      description
        "A textual description of Softwire.";
    }
    container binding {
      if-feature binding;
      description
        "lw4over6 (binding) configuration.";
      container br {
        if-feature br;
        description
          "Indicate this instance supports the lwAFTR (BR) function.
          The instances advertise the BR feature through the
          capability exchange mechanism when a NETCONF session is
          established.";
        leaf enable {
          type boolean;
          description
            "Enable/disable the lwAFTR (BR) function.";
        }
        container br-instances {
          description
            "A set of BRs to be configured.";
          list br-instance {
            key "id";
            description
            "A set of lwAFTRs to be configured.";
            container binding-table-version {
              description "binding table's version";
              leaf binding-table-version{
                type uint64;
                description "Incremental version number
                to the binding table";
              }
              leaf binding-table-date {
                type yang:date-and-time;
                description "Timestamp to the binding
                table";
              }
            }
            leaf id {
              type uint32;
              mandatory true;
              description "An instance identifier.";

Sun, et al.                Expires May 4, 2017                 [Page 16]
Internet-Draft           YANG for A+P Softwires             October 2016

            }
            leaf name {
              type string;
              description "The name for the lwaftr.";
            }
            leaf softwire-num-threshold {
              type uint32;
              mandatory true;
              description
                "The maximum number of tunnels that can be created on
                the lwAFTR.";
            }
            leaf tunnel-payload-mtu {
              type uint16;
              mandatory true;
              description
                "The payload MTU for Lightweight 4over6 tunnel.";
            }
            leaf tunnel-path-mru {
              type uint16;
              mandatory true;
              description
                "The path MRU for Lightweight 4over6 tunnel.";
            }
            container binding-table {
              description "binding table";
              list binding-entry {
                key "binding-ipv6info";
                description "binding entry";
                uses binding-entry;
              }
            }
          }
        }
      }

      container ce {
        if-feature ce;
        description
          "Indicate this instance supports the lwB4 (CE) function.
          The instances advertise the CE feature through the
          capability exchange mechanism when a NETCONF session is
          established.";
        leaf enable {
          type boolean;
          description
            "Enable/disable the lwB4 (CE) function.";
        }

Sun, et al.                Expires May 4, 2017                 [Page 17]
Internet-Draft           YANG for A+P Softwires             October 2016

        container ce-instances {
          description
            "A set of CEs to be configured.";
          list ce-instance {
            key "binding-ipv6info";
            description "instances for CE";
            leaf name {
              type string;
              description "The CE's name.";
            }
            leaf tunnel-payload-mtu {
              type uint16;
              mandatory true;
              description
                "The payload MTU for Lightweight 4over6 tunnel.";
            }
            leaf tunnel-path-mru {
              type uint16;
              mandatory true;
              description
                "The path MRU for Lightweight 4over6 tunnel.";
            }
            leaf b4-ipv6-addr-format {
              type boolean;
              mandatory true;
              description
               "The format of lwB4 (CE) IPv6 address. If set to true,
               it indicates that the IPv6 source address of the lwB4
               is constructed according to the description in
               [RFC7596]; if set to false, the lwB4 (CE)
               can use any /128 address from the assigned IPv6
               prefix.";
            }
            uses binding-entry;
          }
        }
      }
    }

    container algorithm {
      if-feature algorithm;
      description
        "Indicate the instances support the MAP-E and MAP-T function.
        The instances advertise the map-e feature through the
        capability exchange mechanism when a NETCONF session is
        established.";
      leaf enable {
        type boolean;

Sun, et al.                Expires May 4, 2017                 [Page 18]
Internet-Draft           YANG for A+P Softwires             October 2016

        description
          "Enable/disable the MAP-E or MAP-T function.";
      }
      container algo-instances {
        description
          "A set of MAP-E or MAP-T instances to be configured,
           applying to BRs and CEs. A MAP-E/T instance defines a MAP
           domain comprising one or more MAP-CE and MAP-BR";
        list algo-instance {
          key "id";
          description "instance for MAP-E/MAP-T";
          container algo-versioning {
            description "algorithm's version";
            leaf algo-version {
              type uint64;
              description "Incremental version number to
              the algorithm";
            }
            leaf algo-date {
              type yang:date-and-time;
              description "Timestamp to the algorithm";
            }
          }
          leaf id {
            type uint32;
            mandatory true;
            description "Algorithm Instance ID";
          }
          leaf name {
            type string;
            description "The name for the instance.";
          }
          leaf data-plane {
            type enumeration {
              enum "encapsulation" {
                description "encapsulation for MAP-E";
              }
              enum "translation" {
                description "translation for MAP-T";
              }
            }
            description
              "Encapsulation is for MAP-E while translation is
              for MAP-T";
          }
          leaf ea-len {
            type uint8;
            mandatory true;

Sun, et al.                Expires May 4, 2017                 [Page 19]
Internet-Draft           YANG for A+P Softwires             October 2016

            description
              "Embedded Address (EA) bits are the IPv4 EA-bits
              in the IPv6 address identify an IPv4
              prefix/address (or part thereof) or
              a shared IPv4 address (or part thereof)
              and a port-set identifier.
              The length of the EA-bits is defined as
              part of a MAP rule for a MAP domain.";
          }
          leaf rule-ipv6-prefix {
            type inet:ipv6-prefix;
            mandatory true;
            description
              "The Rule IPv6 prefix defined in the mapping rule.";
          }
          leaf rule-ipv4-prefix {
            type inet:ipv4-prefix;
            mandatory true;
            description
              "The Rule IPv4 prefix defined in the mapping rule.";
          }
          leaf forwarding {
            type boolean;
            mandatory true;
            description
              "This parameter specifies whether the rule may be used for
              forwarding (FMR). If set, this rule is used as an FMR;
              if not set, this rule is a BMR only and must not be used
              for forwarding.";
          }
          leaf psid-offset {
            type uint8 {
              range 0..16;
            }
            mandatory true;
            description
              "The number of offset bits. In Lightweight 4over6, the default
              value is 0 for assigning one contiguous port range. In MAP-E/T,
              the default value is 6, which excludes system ports by default
              and assigns distributed port ranges. If the this parameter is
              larger than 0, the value of offset MUST be greater than 0.";
          }
          leaf psid-len {
            type uint8 {
              range 0..15;
            }
            mandatory true;
            description

Sun, et al.                Expires May 4, 2017                 [Page 20]
Internet-Draft           YANG for A+P Softwires             October 2016

              "The length of PSID, representing the sharing ratio for an
              IPv4 address.";
          }
          leaf tunnel-payload-mtu {
            type uint16;
            description
              "The payload MTU for MAP-E tunnel.";
          }
          leaf tunnel-path-mru {
            type uint16;
            description
              "The path MRU for MAP-E tunnel.";
          }
          leaf br-ipv6-addr {
            type inet:ipv6-address;
            mandatory true;
            description
              "The IPv6 address of the MAP-E BR.";
          }
          leaf dmr-ipv6-prefix {
            type inet:ipv6-prefix;
            description
              "The IPv6 prefix of the MAP-T BR. ";
          }
        }
      }
    }
  }

/*
 * Operational state Data Nodes
 */

  container softwire-state {
    config false;
    description
      "The operational state data for Softwire instances. ";
    leaf description {
      type string;
      description
        "A textual description of the softwire instances.";
    }
    container binding {
      if-feature binding;
      description
        "lw4over6 (binding) state.";
      container br {
        if-feature br;

Sun, et al.                Expires May 4, 2017                 [Page 21]
Internet-Draft           YANG for A+P Softwires             October 2016

        config false;
        description
          "Indicate this instance supports the lwAFTR (BR) function.
          The instances advertise the lwaftr (BR) feature through the
          capability exchange mechanism when a NETCONF session is
          established.";
        container br-instances {
          description
            "A set of BRs.";
          list br-instance {
            key "id";
            description "instances for BR";
            leaf id {
              type uint32;
              mandatory true;
              description "id";
            }
            leaf name {
              type string;
              description "The name for this lwaftr.";
            }
            uses traffic-stat;
            leaf active-softwire-num {
              type uint32;
              description
                "The number of currently active tunnels on the
                lw4over6 (binding) instance.";
            }
            container binding-table {
              description "id";
              list binding-entry {
                key "binding-ipv6info";
                description "An identifier of the binding entry.";
                leaf binding-ipv6info {
                  type union {
                    type inet:ipv6-address;
                    type inet:ipv6-prefix;
                  }
                  mandatory true;
                  description
                    "The IPv6 information used to identify
                      a binding entry. ";
                }
                leaf active {
                  type boolean;
                  description
                    "Status of a specific tunnel.";
                }

Sun, et al.                Expires May 4, 2017                 [Page 22]
Internet-Draft           YANG for A+P Softwires             October 2016

              }
            }
          }
        }
      }

      container ce {
        if-feature ce;
        config false;
        description
          "Indicate this instance supports the lwB4 (CE) function.
          The instances advertise the lwb4 (CE) feature through the
          capability exchange mechanism when a NETCONF session is
          established.";
        container ce-instances {
          description
            "Status of the configured CEs.";
          list ce-instance {
            key "binding-ipv6info";
            description "a lwB4 (CE) instance.";
            leaf name {
              type string;
              description "The CE's name.";
            }
            leaf binding-ipv6info {
              type union {
                type inet:ipv6-address;
                type inet:ipv6-prefix;
              }
              mandatory true;
              description
                "The IPv6 information used to identify
                 a binding entry. ";
            }
            uses traffic-stat;
          }
        }
      }
    }

    container algorithm {
      if-feature algorithm;
      config false;
      description
        "Indicate the instances support the MAP-E and MAP-T function.
        The instances advertise the map-e/map-t feature through the
        capability exchange mechanism when a NETCONF session is

Sun, et al.                Expires May 4, 2017                 [Page 23]
Internet-Draft           YANG for A+P Softwires             October 2016

        established.";
      container algo-instances {
        description
          "Status of MAP-E instance(s).";
        list algo-instance {
          key "id";
          description "Instances for algorithm";
          leaf id {
            type uint32;
            mandatory true;
            description "id";
          }
          leaf name {
            type string;
            description "The map-e instance name.";

          }
          uses traffic-stat;
        }
      }
    }
  }

/*
 * Notifications
 */
  notification softwire-br-event {
    if-feature binding;
    if-feature br;
    description "Notification for BR.";

    leaf br-id {
      type leafref {
        path
          "/softwire-state/binding/br/br-instances/"
          + "br-instance/id";
      }
          description "...";
    }
    leaf-list invalid-entry {
      type leafref {
        path
          "/softwire-config/binding/br/br-instances/"
          + "br-instance[id=current()/../br-id]/"
          + "binding-table/binding-entry/binding-ipv6info";
      }
      description
        "Notify the client that a specific binding entry has been

Sun, et al.                Expires May 4, 2017                 [Page 24]
Internet-Draft           YANG for A+P Softwires             October 2016

        expired/invalid. The binding-ipv6info identifies an entry.";
    }
    leaf-list added-entry {
        type inet:ipv6-address;
        description
          "Notify the client that a binding entry has been added.
          The ipv6 address of that entry is the index. The client
          get other information from the lwaftr about the entry
          indexed by that ipv6 address.
          ";
    }
    leaf-list modified-entry {
        type leafref {
          path
            "/softwire-config/binding/br/br-instances/"
            + "br-instance[id=current()/../br-id]/"
            + "binding-table/binding-entry/binding-ipv6info";
        }
          description "...";
    }
  }

  notification softwire-ce-event {
    if-feature binding;
    if-feature ce;
    description "CE notification";
    leaf ce-binding-ipv6-addr-change {
      type inet:ipv6-address;
      mandatory true;
      description
        "The source tunnel IPv6 address of the lwB4.
         If 'b4-ipv6-addr-format' is false, or the lwb4's
         binding-ipv6-address changes for any reason,
         it SHOULD notify the NETCONF client.";
    }
  }

  notification softwire-algorithm-instance-event {
    if-feature algorithm;
    description "Notifications for MAP-E or MAP-T.";
    leaf algo-id {
      type leafref {
        path
          "/softwire-config/algorithm/algo-instances/algo-instance/id";
      }
      mandatory true;
      description "MAP-E or MAP-T event.";
    }

Sun, et al.                Expires May 4, 2017                 [Page 25]
Internet-Draft           YANG for A+P Softwires             October 2016

    leaf-list invalid-entry-id {
      type leafref {
        path
          "/softwire-config/algorithm/algo-instances/algo-instance/id";
      }
      description "Invalid entry event.";
    }
    leaf-list added-entry {
      type leafref {
        path
          "/softwire-config/algorithm/algo-instances/algo-instance/id";
      }
      description "Added entry.";
    }
    leaf-list modified-entry {
      type leafref {
        path
          "/softwire-config/algorithm/algo-instances/algo-instance/id";
      }
      description "Modified entry.";
    }
  }
}
<CODE ENDS>

7.  Configuration Example for a lw4o6 Binding-Table

   The lwAFTR maintains an address binding table which contains the
   following 3-tuples:

   o  IPv6 Address for a single lwB4

   o  Public IPv4 Address

   o  Restricted port-set

   The entry has two functions: the IPv6 encapsulation of inbound IPv4
   packets destined to the lwB4 and the validation of outbound IPv4-in-
   IPv6 packets received from the lwB4 for de-capsulation.

   Consider an example to add an entry that maintains the relationship
   between 3-tuples of lwB4 (2001:db8::1), '192.0.2.1' and '1234' in the
   binding table of the lwAFTR (2001:db8::2).  Here is the example
   binding-table configuration xml:

Sun, et al.                Expires May 4, 2017                 [Page 26]
Internet-Draft           YANG for A+P Softwires             October 2016

     <rpc message-id="101"
       xmlns:nc="urn:params:xml:ns:yang:ietf-softwire:1.0">
   <!-- replace with IANA namespace when assigned. -->
     <edit-config>
       <target>
         <running/>
       </target>
     <softwire-config>
       <lw4o6-aftr>
         <lw4o6-aftr-instances>
           <lw4o6-aftr-instance>
             <aftr-ipv6-addr>2001:db8::2</aftr-ipv6-addr>
             <binding-table>
               <binding-entry>
                 <binding-ipv4-addr>192.0.2.1</binding-ipv4-addr>
                 <port-set>
                   <psid>1234</psid>
                 </port-set>
                 <binding-ipv6-addr>2001:db8::1</binding-ipv6-addr>
                 <active>1</active>
               </binding-entry>
             </binding-table>
           </lw4o6-aftr-instance>
         </lw4o6-aftr-instances>
       </lw4o6-aftr>
     </softwire-config>

              Figure 5: lw4o6 Binding-Table Configuration XML

7.1.  Configuration Example for a MAP-E BR

   A MAP-E BR is configured with forward mapping rules for the clients
   it is serving.  In this example (taken from [RFC7597], Appendix A,
   Example 2), the following parameters are required:

   o  Rule IPv6 Prefix

   o  Rule IPv4 Prefix

   o  Rule EA-bit bit length

   o  IPv6 Address of MAP-BR

   The mapping rule has two functions: identifying the destination CE
   IPv6 address for encapsulating inbound IPv4 packets and the
   validation of outbound IPv4-in-IPv6 packets received from the CE for
   de-capsulation.

Sun, et al.                Expires May 4, 2017                 [Page 27]
Internet-Draft           YANG for A+P Softwires             October 2016

   The transport type for the data plane also needs to be configured for
   encapsulation to enable MAP-E and forwarding needs to be enabled.

   Consider an example for the following MAP-E Forwarding Mapping Rule:

   Data plane:         encapsulation

   Rule IPv6 Prefix:   2001:db8::/40

   Rule IPv4 Prefix:   192.0.2.0/24

   Rule EA-bit Length: 16

   BR IPv6 Address:    2001:db8:ffff::1

   Here is the example MAP-E BR configuration xml:

     <rpc message-id="101"
       xmlns:nc="urn:params:xml:ns:yang:ietf-softwire:1.0">
   <!-- replace with IANA namespace when assigned. -->
     <edit-config>
       <target>
         <running/>
       </target>
     <softwire-config>
       <algorithm>
         <algo-instance>
           <data-plane>encapsulation</data-plane>
           <ea-len>16</ea-len>
           <rule-ipv6-prefix>2001:db8::/40</rule-ipv6-prefix>
           <rule-ipv4-prefix>192.0.2.0/24</rule-ipv4-prefix>
           <forwarding>1</forwarding>
           <br-ipv6-addr>2001:db8:ffff::1</br-ipv6-addr>
         </algo-instance>
       </algorithm>
     </softwire-config>

                   Figure 6: MAP-E FMR Configuration XML

8.  Security Considerations

   The YANG module defined in this memo is designed to be accessed via
   the NETCONF protocol [RFC6241].  The lowest NETCONF layer is the
   secure transport layer and the mandatory to implement secure
   transport is SSH [RFC6242].  The NETCONF access control model
   [RFC6536] provides the means to restrict access for particular
   NETCONF users to a pre-configured subset of all available NETCONF
   protocol operations and content.

Sun, et al.                Expires May 4, 2017                 [Page 28]
Internet-Draft           YANG for A+P Softwires             October 2016

   All data nodes defined in the YANG module which can be created,
   modified and deleted (i.e., config true, which is the default).
   These data nodes are considered sensitive.  Write operations (e.g.,
   edit-config) applied to these data nodes without proper protection
   can negatively affect network operations.

9.  IANA Considerations

   This document requests IANA to register the following URI in the
   "IETF XML Registry" [RFC3688].

               URI: urn:ietf:params:xml:ns:yang:softwire
               Registrant Contact: The IESG.
               XML: N/A; the requested URI is an XML namespace.

   This document requests IANA to register the following YANG module in
   the "YANG Module Names" registry [RFC6020].

               name: ietf-softwire
               namespace: urn:ietf:params:xml:ns:yang:softwire
               prefix: softwire
               reference: RFC XXXX

10.  Acknowledgements

   The authors would like to thank Lishan Li, Bert Wijnen, Giles Heron,
   and Ole Troan for their contributions to this work.

11.  References

11.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              DOI 10.17487/RFC3688, January 2004,
              <http://www.rfc-editor.org/info/rfc3688>.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              DOI 10.17487/RFC6020, October 2010,
              <http://www.rfc-editor.org/info/rfc6020>.

Sun, et al.                Expires May 4, 2017                 [Page 29]
Internet-Draft           YANG for A+P Softwires             October 2016

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <http://www.rfc-editor.org/info/rfc6241>.

   [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
              Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
              <http://www.rfc-editor.org/info/rfc6242>.

   [RFC6536]  Bierman, A. and M. Bjorklund, "Network Configuration
              Protocol (NETCONF) Access Control Model", RFC 6536,
              DOI 10.17487/RFC6536, March 2012,
              <http://www.rfc-editor.org/info/rfc6536>.

   [RFC7596]  Cui, Y., Sun, Q., Boucadair, M., Tsou, T., Lee, Y., and I.
              Farrer, "Lightweight 4over6: An Extension to the Dual-
              Stack Lite Architecture", RFC 7596, DOI 10.17487/RFC7596,
              July 2015, <http://www.rfc-editor.org/info/rfc7596>.

   [RFC7597]  Troan, O., Ed., Dec, W., Li, X., Bao, C., Matsushima, S.,
              Murakami, T., and T. Taylor, Ed., "Mapping of Address and
              Port with Encapsulation (MAP-E)", RFC 7597,
              DOI 10.17487/RFC7597, July 2015,
              <http://www.rfc-editor.org/info/rfc7597>.

   [RFC7598]  Mrugalski, T., Troan, O., Farrer, I., Perreault, S., Dec,
              W., Bao, C., Yeh, L., and X. Deng, "DHCPv6 Options for
              Configuration of Softwire Address and Port-Mapped
              Clients", RFC 7598, DOI 10.17487/RFC7598, July 2015,
              <http://www.rfc-editor.org/info/rfc7598>.

   [RFC7599]  Li, X., Bao, C., Dec, W., Ed., Troan, O., Matsushima, S.,
              and T. Murakami, "Mapping of Address and Port using
              Translation (MAP-T)", RFC 7599, DOI 10.17487/RFC7599, July
              2015, <http://www.rfc-editor.org/info/rfc7599>.

11.2.  Informative References

   [I-D.ietf-netmod-routing-cfg]
              Lhotka, L. and A. Lindem, "A YANG Data Model for Routing
              Management", draft-ietf-netmod-routing-cfg-24 (work in
              progress), October 2016.

   [I-D.ietf-softwire-dslite-yang]
              Boucadair, M., Jacquenet, C., and S. Sivakumar, "A YANG
              Data Model for the DS-Lite Address Family Transition
              Router (AFTR)", draft-ietf-softwire-dslite-yang-00 (work
              in progress), August 2016.

Sun, et al.                Expires May 4, 2017                 [Page 30]
Internet-Draft           YANG for A+P Softwires             October 2016

   [I-D.sivakumar-yang-nat]
              Sivakumar, S., Boucadair, M., and S. <>, "YANG Data Model
              for Network Address Translation (NAT)", draft-sivakumar-
              yang-nat-05 (work in progress), September 2016.

   [RFC6991]  Schoenwaelder, J., Ed., "Common YANG Data Types",
              RFC 6991, DOI 10.17487/RFC6991, July 2013,
              <http://www.rfc-editor.org/info/rfc6991>.

Authors' Addresses

   Qi Sun
   Tsinghua University
   Beijing  100084
   P.R. China

   Phone: +86-10-6278-5822
   Email: sunqi.ietf@gmail.com

   Hao Wang
   Tsinghua University
   Beijing  100084
   P.R. China

   Phone: +86-10-6278-5822
   Email: wangh13@mails.tsinghua.edu.cn

   Yong Cui
   Tsinghua University
   Beijing  100084
   P.R. China

   Phone: +86-10-6260-3059
   Email: yong@csnet1.cs.tsinghua.edu.cn

   Ian Farrer
   Deutsche Telekom AG
   CTO-ATI,Landgrabenweg 151
   Bonn, NRW  53227
   Germany

   Email: ian.farrer@telekom.de

Sun, et al.                Expires May 4, 2017                 [Page 31]
Internet-Draft           YANG for A+P Softwires             October 2016

   Sladjana Zoric
   Deutsche Telekom AG
   CTO-IPT,Landgrabenweg 151
   Bonn, NRW  53227
   Germany

   Email: sladjana.zoric@telekom.de

   Mohamed Boucadair
   Orange
   Rennes  35000
   France

   Email: mohamed.boucadair@orange.com

   Rajiv Asati
   Cisco Systems, Inc.
   7025 Kit Creek Rd.
   RTP, NC  27709
   USA

   Email: Rajiva@cisco.com

Sun, et al.                Expires May 4, 2017                 [Page 32]