Skip to main content

Routing for RPL Leaves
draft-ietf-roll-unaware-leaves-04

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 9010.
Authors Pascal Thubert , Michael Richardson
Last updated 2019-09-09 (Latest revision 2019-08-30)
Replaces draft-thubert-roll-unaware-leaves
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Associated WG milestone
Mar 2020
Initial submission of routing for RPL Leaves draft to the IESG
Document shepherd (None)
IESG IESG state Became RFC 9010 (Proposed Standard)
Consensus boilerplate Yes
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-roll-unaware-leaves-04
ROLL                                                     P. Thubert, Ed.
Internet-Draft                                                     Cisco
Updates: 6550, 8505 (if approved)                          M. Richardson
Intended status: Standards Track                               Sandelman
Expires: March 12, 2020                                September 9, 2019

                         Routing for RPL Leaves
                   draft-ietf-roll-unaware-leaves-04

Abstract

   This specification extends RFC6550 and RFC8505 to provide unicast and
   multicast routing services in a RPL domain to 6LNs that are plain
   hosts and do not participate to RPL.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on March 12, 2020.

Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Thubert & Richardson     Expires March 12, 2020                 [Page 1]
Internet-Draft           Routing for RPL Leaves           September 2019

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   4
     2.1.  BCP 14  . . . . . . . . . . . . . . . . . . . . . . . . .   4
     2.2.  References  . . . . . . . . . . . . . . . . . . . . . . .   4
     2.3.  Glossary  . . . . . . . . . . . . . . . . . . . . . . . .   5
   3.  6LoWPAN Neighbor Discovery  . . . . . . . . . . . . . . . . .   6
     3.1.  RFC 6775  . . . . . . . . . . . . . . . . . . . . . . . .   7
     3.2.  RFC 8505 Extended ARO . . . . . . . . . . . . . . . . . .   7
       3.2.1.  R Flag  . . . . . . . . . . . . . . . . . . . . . . .   8
       3.2.2.  TID, I Field and Opaque Fields  . . . . . . . . . . .   8
       3.2.3.  ROVR  . . . . . . . . . . . . . . . . . . . . . . . .   8
     3.3.  RFC 8505 Extended DAR/DAC . . . . . . . . . . . . . . . .   9
   4.  Updating RFC 6550 . . . . . . . . . . . . . . . . . . . . . .   9
   5.  Updating RFC 8505 . . . . . . . . . . . . . . . . . . . . . .  10
   6.  6LN Requirements to be a RPL-Unware Leaf  . . . . . . . . . .  10
     6.1.  Support of 6LoWPAN ND . . . . . . . . . . . . . . . . . .  10
     6.2.  External Routes and RPL Artifacts . . . . . . . . . . . .  11
       6.2.1.  Support of the HbH Header . . . . . . . . . . . . . .  11
       6.2.2.  Support of the Routing Header . . . . . . . . . . . .  11
       6.2.3.  Support of IPv6 Encapsulation . . . . . . . . . . . .  12
   7.  Updated RPL Target option . . . . . . . . . . . . . . . . . .  12
   8.  Protocol Operations for Unicast Addresses . . . . . . . . . .  13
     8.1.  General Flow  . . . . . . . . . . . . . . . . . . . . . .  13
       8.1.1.  In RPL Non-Storing-Mode . . . . . . . . . . . . . . .  14
       8.1.2.  In RPL Storing-Mode . . . . . . . . . . . . . . . . .  16
     8.2.  Operation . . . . . . . . . . . . . . . . . . . . . . . .  17
       8.2.1.  By the 6LN  . . . . . . . . . . . . . . . . . . . . .  17
       8.2.2.  By the 6LR  . . . . . . . . . . . . . . . . . . . . .  18
       8.2.3.  By the RPL Root . . . . . . . . . . . . . . . . . . .  20
       8.2.4.  By the 6LBR . . . . . . . . . . . . . . . . . . . . .  21
   9.  Protocol Operations for Multicast Addresses . . . . . . . . .  21
   10. Implementation Status . . . . . . . . . . . . . . . . . . . .  23
   11. Security Considerations . . . . . . . . . . . . . . . . . . .  23
   12. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  24
     12.1.  RPL Target Option Flags  . . . . . . . . . . . . . . . .  24
     12.2.  New Subsubregistry for the Status values of the RPL DAO-
            ACK Message  . . . . . . . . . . . . . . . . . . . . . .  24
   13. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  25
   14. References  . . . . . . . . . . . . . . . . . . . . . . . . .  26
     14.1.  Normative References . . . . . . . . . . . . . . . . . .  26
     14.2.  Informative References . . . . . . . . . . . . . . . . .  28
   Appendix A.  Example Compression  . . . . . . . . . . . . . . . .  29
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  30

Thubert & Richardson     Expires March 12, 2020                 [Page 2]
Internet-Draft           Routing for RPL Leaves           September 2019

1.  Introduction

   The design of Low Power and Lossy Networks (LLNs) is generally
   focused on saving energy, which is the most constrained resource of
   all.  Other design constraints, such as a limited memory capacity,
   duty cycling of the LLN devices and low-power lossy transmissions,
   derive from that primary concern.

   The IETF produced the "Routing Protocol for Low Power and Lossy
   Networks" [RFC6550] (RPL) to provide IPv6 [RFC8200] routing services
   within such constraints.  RPL is a Distance-Vector protocol, which,
   compared to link-state protocols, limits the amount of topological
   knowledge that needs to be installed and maintained in each node.  In
   order to operate in constrained networks, RPL allows a Routing
   Stretch (see [RFC6687]), whereby routing is only performed along a
   DODAG as opposed to straight along a shortest path between 2 peers,
   whatever that would mean in a given LLN.  This trades the quality of
   peer-to-peer (P2P) paths for a vastly reduced amount of control
   traffic and routing state that would be required to operate a any-to-
   any shortest path protocol.  Finally, broken routes may be fixed
   lazily and on-demand, based on dataplane inconsistency discovery,
   which avoids wasting energy in the proactive repair of unused paths.

   In order to cope with lossy transmissions, RPL forms Direction-
   Oriented Directed Acyclic Graphs (DODAGs) using DODAG Information
   Solicitation (DIS) and DODAG Information Object (DIO) messages.  For
   most of the nodes, though not all, a DODAG provides multiple
   forwarding solutions towards the Root of the topology via so-called
   parents.  RPL is designed to adapt to fuzzy connectivity, whereby the
   physical topology cannot be expected to reach a stable state, with a
   lazy control that creates routes proactively but only fixes them when
   they are used by actual traffic.  The result is that RPL provides
   reachability for most of the LLN nodes, most of the time, but may not
   really converge in the classical sense.  RPL provides unicast and
   multicast routing services back to RPL-Aware nodes (RANs).  A RAN
   will inject routes to itself using Destination Advertisement Object
   (DAO) messages sent to either parent-nodes in Storing Mode or to the
   Root indicating their parent in Non-Storing Mode.  This process
   effectively forms a DODAG back to the device that is a subset of the
   DODAG to the Root with all links reversed.

   When a routing protocol such as RPL is used to maintain reachability
   within a Non-Broadcast Multi-Access (NBMA) subnet, some nodes may act
   as routers and participate to the routing operations whereas others
   may be plain hosts.  In [RFC6550] terms, a host that is reachable
   over the RPL network is called a Leaf.

Thubert & Richardson     Expires March 12, 2020                 [Page 3]
Internet-Draft           Routing for RPL Leaves           September 2019

   "When to use RFC 6553, 6554 and IPv6-in-IPv6"
   [I-D.ietf-roll-useofrplinfo] introduces the term RPL-Aware-Leaf (RAL)
   for a leaf that injects routes in RPL to manage the reachability of
   its own IPv6 addresses.  In contrast, a RPL-Unaware Leaf (RUL)
   designates a leaf does not participate to RPL at all.  In that case,
   the 6LN is a plain host that needs an interface to its RPL router to
   obtain routing services over the LLN.  This specification enables a
   RPL-Unaware Leaf (RUL) to announce itself as a host and request that
   6LRs that accept the registration also inject the relevant routing
   information for the Registered Address in the RPL domain on its
   behalf.  The unicast packet forwarding operation by the 6LR serving a
   Leaf 6LN is described in [I-D.ietf-roll-useofrplinfo].

   Examples of routing-agnostic 6LN may include lightly-powered sensors
   such as window smash sensor (alarm system), or the kinetically
   powered light switch.  Other application of this specification may
   include a smart grid network that controls appliances - such as
   washing machines or the heating system - in the home.  Applicances
   may not participate to the RPL protocol operated in the smart grid
   network but can still receive control packet from the smart grid.

2.  Terminology

2.1.  BCP 14

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119][RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.2.  References

   The Terminology used in this document is consistent with and
   incorporates that described in Terms Used in Routing for Low-Power
   and Lossy Networks (LLNs).  [RFC7102].

   A glossary of classical 6LoWPAN acronyms is given in Section 2.3.

   The term "byte" is used in its now customary sense as a synonym for
   "octet".

   "RPL", the "RPL Packet Information" (RPI), "RPL Instance" (indexed by
   a RPLInstanceID)are defined in "RPL: IPv6 Routing Protocol for Low-
   Power and Lossy Networks" [RFC6550] .  The DODAG Information
   Solicitation (DIS), Destination Advertisement Object (DAO) and DODAG
   Information Object (DIO) messages are also specified in [RFC6550].

Thubert & Richardson     Expires March 12, 2020                 [Page 4]
Internet-Draft           Routing for RPL Leaves           September 2019

   The Destination Cleanup Object (DCO) message is defined in
   [I-D.ietf-roll-efficient-npdao].

   This document uses the terms RPL-Unaware Leaf (RUL) and RPL Aware
   Leaf (RAL) consistently with [I-D.ietf-roll-useofrplinfo].  The term
   RPL-Aware Node (RAN) is introduced to refer to a node that is either
   a RAL or a RPL router.  As opposed to a RUL, a RAN manages the
   reachability of its addresses and prefixes by injecting them in RPL
   by itself.

   Other terms in use in LLNs are found in Terminology for Constrained-
   Node Networks [RFC7228].

   Readers are expected to be familiar with all the terms and concepts
   that are discussed in

   o  "Neighbor Discovery for IP version 6" [RFC4861],

   o  "IPv6 Stateless Address Autoconfiguration" [RFC4862],

   o  "Problem Statement and Requirements for IPv6 over Low-Power
      Wireless Personal Area Network (6LoWPAN) Routing" [RFC6606],

   o  "IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs):
      Overview, Assumptions, Problem Statement, and Goals" [RFC4919],

   o  "Neighbor Discovery Optimization for Low-power and Lossy Networks"
      [RFC6775], and

   o  "Registration Extensions for IPv6 over Low-Power Wireless Personal
      Area Network (6LoWPAN) Neighbor Discovery" [RFC8505].

2.3.  Glossary

   This document often uses the following acronyms:

   AR:   Address Resolution (aka Address Lookup)

   6LBR: 6LoWPAN Border Router

   6LN:  6LoWPAN Node (a Low Power host or router)

   6LR:  6LoWPAN Router

   6CIO: Capability Indication Option

   (E)ARO:  (Extended) Address Registration Option

Thubert & Richardson     Expires March 12, 2020                 [Page 5]
Internet-Draft           Routing for RPL Leaves           September 2019

   (E)DAR:  (Extended) Duplicate Address Request

   (E)DAC:  (Extended) Duplicate Address Confirmation

   DAD:  Duplicate Address Detection

   DAO:  Destination Advertisement Object

   DCO:  Destination Cleanup Object

   DIS:  DODAG Information Solicitation

   DIO:  DODAG Information Object

   DODAG:  Destination-Oriented Directed Acyclic Graph

   LLN:  Low-Power and Lossy Network

   NA:   Neighbor Advertisement

   NCE:  Neighbor Cache Entry

   ND:   Neighbor Discovery

   NDP:  Neighbor Discovery Protocol

   NS:   Neighbor Solicitation

   RA:   Router Advertisement

   ROVR: Registration Ownership Verifier

   RPI:  RPL Packet Information (an Option in the Hop-By_Hop Header)

   RAL:  RPL-Aware Leaf

   RAN:  RPL-Aware Node (either a RPL router or a RPL-Aware Leaf)

   RUL:  RPL-Unaware Leaf

   TID:  Transaction ID (a sequence counter in the EARO)

3.  6LoWPAN Neighbor Discovery

Thubert & Richardson     Expires March 12, 2020                 [Page 6]
Internet-Draft           Routing for RPL Leaves           September 2019

3.1.  RFC 6775

   The "IPv6 Neighbor Discovery (IPv6 ND) Protocol" (NDP) suite
   [RFC4861] [RFC4862] was defined for transit media such a Ethernet,
   and relies heavily on multicast operations for address discovery and
   duplicate address detection (DAD).

   "Neighbor Discovery Optimizations for 6LoWPAN networks" [RFC6775]
   (6LoWPAN ND) adapts IPv6 ND for operations over energy-constrained
   LLNs.  In particular, 6LoWPAN ND introduces a unicast host address
   registration mechanism that contributes to reducing the use of
   multicast messages that are present in the classical IPv6 ND
   protocol. 6LoWPAN ND defines a new Address Registration Option (ARO)
   that is carried in the unicast Neighbor Solicitation (NS) and
   Neighbor Advertisement (NA) messages between the 6LoWPAN Node (6LN)
   and the 6LoWPAN Router (6LR).

   6LoWPAN ND also defines the Duplicate Address Request (DAR) and
   Duplicate Address Confirmation (DAC) messages between the 6LR and the
   6LoWPAN Border Router (6LBR).  In an LLN, the 6LBR is the central
   repository of all the Registered Addresses in its domain.

   The main functions of [RFC6775] are to proactively establish the
   Neighbor Cache Entry in the 6LR and to avoid address duplication.
   There is no concept of registering the address for an external
   service such as RPL routing.  That feature is introduced with
   "Registration Extensions for 6LoWPAN Neighbor Discovery" [RFC8505].

3.2.  RFC 8505 Extended ARO

   [RFC8505] updates the behavior of RFC 6775 to enable a generic
   registration to services such as routing, and defines an Extended ARO
   (EARO).  The format of the EARO is shown in Figure 1:

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Type      |     Length    |    Status     |    Opaque     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |  Rsvd | I |R|T|     TID       |     Registration Lifetime     |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                                                               |
    ...             Registration Ownership Verifier                 ...
     |                                                               |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 1: EARO Option Format

Thubert & Richardson     Expires March 12, 2020                 [Page 7]
Internet-Draft           Routing for RPL Leaves           September 2019

3.2.1.  R Flag

   [RFC8505] introduces the R flag in the EARO.  The Registering Node
   sets the R flag to indicate whether the 6LR should ensure
   reachability for the Registered Address, e.g., by means of routing or
   proxying ND.  If the R flag is not set, then the Registering Node is
   expected to be a RAN that handles the reachability of the Registered
   Address by itself.

   This document specifies how the R flag is used in the context of RPL.
   A 6LN operates as a RUL for an IPv6 address iff it sets the R flag in
   the NS(EARO) used to register the address.  The RPL router generates
   a DAO message for the Registered Address upon an NS(EARO) iff the R
   flag in the EARO is set.  Conversely, this document specifies a
   behavior of a RPL router acting as 6LR for the registration 6LR that
   depends on the setting of the R flag in the NS(EARO).

3.2.2.  TID, I Field and Opaque Fields

   The EARO also includes a sequence counter called Transaction ID
   (TID), which maps to the Path Sequence Field found in Transit Options
   in RPL DAO messages.  This is the reason why the support of [RFC8505]
   by the RUL as opposed to only [RFC6775] is a prerequisite for this
   specification (more in Section 6.1).  The EARO also transports an
   Opaque field and an "I" field that describes what the Opaque field
   transports and how to use it.  Section 8.2.1 specifies the use of the
   "I" field and of the Opaque field by a RUL.

3.2.3.  ROVR

   Section 5.3. of [RFC8505] introduces the Registration Ownership
   Verifier (ROVR) field of a variable length from 64 to 256 bits.  The
   ROVR is a replacement of the EUI-64 field in the ARO [RFC6775] that
   was used to identify uniquely a registration based on the Link-Layer
   address of the owner but provided no protection against spoofing.

   "Address Protected Neighbor Discovery for Low-power and Lossy
   Networks" [I-D.ietf-6lo-ap-nd] leverages the ROVR field as a
   cryptographic proof of ownership to prevent a rogue third party from
   misusing the address.  [I-D.ietf-6lo-ap-nd] adds a challenge/response
   exchange to the [RFC8505] registration and enables Source Address
   Validation by a 6LR that will drop packets with a spoofed address.

   This specification does not address how the protection by
   [I-D.ietf-6lo-ap-nd] could be extended to RPL.  On the other hand, it
   adds the ROVR to the DAO to build the proxied EDAR at the Root, which
   means that nodes that are aware of the host route to the 6LN are now
   aware of the associated ROVR as well.

Thubert & Richardson     Expires March 12, 2020                 [Page 8]
Internet-Draft           Routing for RPL Leaves           September 2019

3.3.  RFC 8505 Extended DAR/DAC

   [RFC8505] updates the periodic DAR/DAC exchange that takes place
   between the 6LR and the 6LBR using Extended DAR/DAC messages.  The
   Extended Duplicate Address messages can carry the ROVR field of
   variable size.  The periodic EDAR/EDAC exchange is triggered by a
   NS(EARO) message and is intended to create and then refresh the
   corresponding state in the 6LBR for a lifetime that is indicated by
   the 6LN.  Conversely, RPL [RFC6550] specifies a periodic DAO from the
   6LN all the way to the Root that maintains the routing state in the
   RPL network for a lifetime that is indicated by the source of the
   DAO.  This means that there are two periodic messages that traverse
   the whole network to indicate that an address is still reachable, one
   to the Root and one to the 6LBR.  This represents a waste of
   bandwidth and energy that can be undesirable in an LLN.

   This specification saves the support of RPL in a 6LN called a RUL and
   avoids an extraneous periodic flow across the LLN.  The RUL only
   needs to perform a [RFC8505] registration to the 6LR.  The 6LR turns
   it into a DAO message to the Root on behalf of the RUL.  Upon the new
   DAO, the Root proxies the EDAR exchange to the 6LBR on behalf of the
   6LR.  This is illustrated in Figure 4.

4.  Updating RFC 6550

   This document specifies a new behavior whereby a 6LR injects DAO
   messages for unicast addresses (see Section 8) and multicast
   addresses (see Section 9) on behalf of leaves that are not aware of
   RPL.  The Targets are exposed as External addresses.  An IP-in-IP
   encapsulation that terminates at the border 6LR is used to remove RPL
   artifacts and compression techniques that may not be processed
   correctly outside of the RPL domain.

   This document synchronizes the liveness monitoring at the Root and
   the 6LBR.  A same value of lifetime is used for both, and a single
   keep alive message, the RPL DAO, traverses the RPL network.  A new
   behavior is introduced whereby the RPL Root proxies the EDAR message
   to the 6LBR on behalf of the 6LR (more in Section 5).  [RFC6550] is
   updated with new RPL Status values for use in DAO-ACK and DCO that
   map the 6LoWPAN ND values defined in Table 1 of [RFC8505].  The
   resulting set is shown in Table 1.

   Section 6.7. of [RFC6550] introduces the RPL Control Message Options
   such as the RPL Target Option that can be included in a RPL Control
   Message such as the DAO.  Section 7 updates the RPL Target Option to
   optionally transport the ROVR used in the IPv6 Registration (see
   Section 3.2.3) so the RPL Root can generate a full EDAR Message.

Thubert & Richardson     Expires March 12, 2020                 [Page 9]
Internet-Draft           Routing for RPL Leaves           September 2019

5.  Updating RFC 8505

   This document updates [RFC8505] to introduce a keep-alive EDAR
   message and a keep-alive NS(EARO) message.  The keep-alive messages
   are used for backward compatibility, when the DAO does not transport
   a ROVR as specified in Section 7.  The keep-alive messages have a
   zero ROVR field and can only be used to refresh a pre-existing state
   associated to the Registered Address.  More specifically, a keep-
   alive message can only increase the lifetime and/or increment the TID
   of the existing state in a 6LBR.

   Upon the renewal of a 6LoWPAN ND registration, this specification
   changes the behavior of a RPL router acting as 6LR for the
   registration as follows.  If the Root indicates the capability to
   proxy the EDAR/EDAC exchange to the 6LBR then the 6LR refrains from
   sending an EDAR message; if the Root is separated from the 6LBR, the
   Root regenerates the EDAR message to the 6LBR upon a DAO message that
   signals the liveliness of the Address.

6.  6LN Requirements to be a RPL-Unware Leaf

   This document provides RPL routing for a RUL, that is a 6LN acting as
   a plain host and not aware of RPL.  Still, a minimal RPL-independent
   functionality is expected from the 6LN in order to obtain routing
   services from the 6LR.

6.1.  Support of 6LoWPAN ND

   A RUL MUST implement [RFC8505] and set the R flag in the EARO option.
   A 6LN is considered to be a RUL if and only if it sets the R flag in
   the EARO.

   A RUL MUST register to all the 6LRs from which it expects to get
   routing services.  The registrations SHOULD be performed in a rapid
   sequence, using the exact same EARO for a same Address.  Gaps between
   the registrations will invalidate some of the routes till the
   registration finally shows on those routes as well.

   [RFC8505] introduces error Status values in the NA(EARO) which can be
   received synchronously upon an NS(EARO) or asynchronously.  The RUL
   MUST support both cases and refrain from using the Registered Address
   as specified by [RFC8505] depending on the Status value.

   A RUL SHOULD support [I-D.ietf-6lo-ap-nd] to protect the ownership of
   its addresses.

Thubert & Richardson     Expires March 12, 2020                [Page 10]
Internet-Draft           Routing for RPL Leaves           September 2019

6.2.  External Routes and RPL Artifacts

   Section 4.1. of [I-D.ietf-roll-useofrplinfo] provides a set of rules
   that MUST be followed when forwarding packets over an external route:

   RPL data packets are often encapsulated using IP-in-IP and in Non-
   Storing Mode, packets going down will carry an SRH as well.  RPL data
   packets also typically carry a Hop-by-Hop Header to transport a RPL
   Packet Information (RPI) [RFC6550].  These additional headers are
   called RPL artifacts.  When IP-in-IP is used and the outer headers
   terminate at a 6LR down the path (see Figure 8 for the compressed
   format in Storing Mode), then the 6LR decapsulates the IP-in-IP and
   the packet that is forwarded to the external destination is free of
   RPL artifacts - but possibly an RPI if packet was generated by a RAN
   in the same RPL domain as the destination RUL.

   An IP-in-IP tunnel to a 6LR that injected the route is used for
   external routes unless the final destination is known to handle or
   ignore the RPL artifacts properly [RFC8200].  Non-Storing Mode
   signaling is used to signal external routes to the Root, which
   enables to advertise the tunnel endpoint.  A RUL is an example of
   target that is reachable via an external host route and is expected
   to ignore the RPI and the consumed SRH artifacts.  In the case of a
   RUL, tunneling may not be necessary.

   A RUL may not support IP-in-IP tunneling [RFC8504], so if IP-in-IP is
   used, and unless the Root as a better knowledge, the tunnel should
   terminate at the 6LR that injected the external route to the RUL.

   Additionally, the RUL cannot be expected to support the compression
   method defined in [RFC8138].  The 6LR that injected the route
   uncompresses the packet before forwarding over an external route,
   even when delivering to a RUL, even when it is not the destination of
   the incoming packet.

6.2.1.  Support of the HbH Header

   A RUL is expected to process an unknown Option Type in a Hop-by-Hop
   Header as prescribed by section 4.2 of [RFC8200].  This means in
   particular that an RPI with an Option Type of 0x23
   [I-D.ietf-roll-useofrplinfo] is ignored when not understood.

6.2.2.  Support of the Routing Header

   A RUL is expected to process an unknown Routing Header Type as
   prescribed by section 4.4 of [RFC8200].  This means in particular
   that Routing Header with a Routing Type of 3 [RFC6553] is ignored
   when the Segments Left is zero, and dropped otherwise.

Thubert & Richardson     Expires March 12, 2020                [Page 11]
Internet-Draft           Routing for RPL Leaves           September 2019

6.2.3.  Support of IPv6 Encapsulation

   Section 2.1 of [I-D.ietf-roll-useofrplinfo] sets the rules for
   forwarding IP-in-IP either to the final 6LN or to a parent 6LR.  In
   order to enable IP-in-IP to the 6LN in Non-Storing Mode, the 6LN must
   be able to decapsulate the tunneled packet and either drop the inner
   packet if it is not the final destination, or pass it to the upper
   layer for further processing.  Unless it is aware that the RUL can
   handle IP-in-IP properly, the Root that encapsulates a packet to a
   RUL terminates the IP-in-IP tunnel at the parent 6LR . For that
   reason, it is beneficial but not necessary for a RUL to support IP-
   in-IP.

7.  Updated RPL Target option

   This specification updates the RPL Target option to transport the
   ROVR as illustrated in Figure 2.  This enables the RPL Root to
   generate a full EDAR Message as opposed to a keep-alive EDAR that has
   restricted properties.  The Target Prefix MUST be aligned to the next
   4-byte boundary after the size indicated by the Prefix Length. if
   necessary it is padded with zeros.  The size of the ROVR is indicated
   in a new ROVR Type field that is encoded to map the CodePfx in the
   EDAR message (see section 4.2 of [RFC8505]).  With this specification
   the ROVR is the remainder of the RPL Target Option.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |   Type = 0x05 | Option Length |ROVRsz | Flags | Prefix Length |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
      +                                                               +
      |                Target Prefix (Variable Length)                |
      .                Aligned to 4-byte boundary                     .
      .                                                               .
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                                                               |
     ...            Registration Ownership Verifier (ROVR)           ...
      |                                                               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                      Figure 2: Updated Target Option

   New fields:

   RVRsz:          Indicates the Size of the ROVR.  It MAY be 1, 2, 3,
                   or 4, denoting a ROVR size of 64, 128, 192, or 256
                   bits, respectively.

Thubert & Richardson     Expires March 12, 2020                [Page 12]
Internet-Draft           Routing for RPL Leaves           September 2019

   Registration Ownership Verifier (ROVR):  This is the same field as in
                   the EARO, see [RFC8505]

8.  Protocol Operations for Unicast Addresses

8.1.  General Flow

   This specification enables to save the exchange of Extended Duplicate
   Address messages, EDAR and EDAC, from a 6LN all the way to the 6LBR
   across a RPL mesh, for the sole purpose of refreshing an existing
   state in the 6LBR.  Instead, the EDAR/EDAC exchange is proxied by the
   RPL Root upon a DAO message that refreshes the RPL routing state.  To
   achieve this, the lifetimes and sequence counters in 6LoWPAN ND and
   RPL are aligned.  In other words, the Path Sequence and the Path
   Lifetime in the DAO message are taken from the Transaction ID and the
   registration lifetime in the NS(EARO) message from the 6LN.

   In that flow, the RPL Root acts as a proxy to refresh the state in
   the 6LBR.  The proxy operation applies to both RUL and RAN.  This
   means that in a RPL network where the function is enabled, refreshing
   the state in the 6LBR is the responsibility of the Root.
   Consequently, only addresses that are injected in RPL will be kept
   alive by the RPL Root.  If an additional routing protocol is deployed
   on a same network, that additional routing protocol may need to
   handle the keep alive procedure for the addresses that it serves.

   From the perspective of the 6LN, the registration flow happens
   transparently; it is not delayed by the proxy RPL operation, so the
   device does not need to change the amount of time it waits based upon
   whether RPL proxy operation happens or not.

   On the first registration, illustrated in Figure 3, from the
   perspective of the 6LR in Non-Storing Mode, the Extended Duplicate
   Address message takes place as prescribed by [RFC8505].  When
   successful, the flow creates a Neighbor Cache Entry (NCE) in the 6LR,
   and the 6LR injects the Registered Address in RPL using DAO/DAO-ACK
   exchanges all the way to the RPL DODAG Root.  The protocol does not
   carry a specific information that the Extended Duplicate Address
   messages were already exchanged, so the Root proxies them anyway.

   Note that any of the functions 6LR, Root and 6LBR might be collapsed
   in a single node, in which case the flow above happens internally,
   and possibly through internal API calls as opposed to messaging.

Thubert & Richardson     Expires March 12, 2020                [Page 13]
Internet-Draft           Routing for RPL Leaves           September 2019

8.1.1.  In RPL Non-Storing-Mode

   In Non-Storing Mode, the flows can be nested as illustrated in
   Figure 3 and it is possible to carry information such as an updated
   lifetime from the 6LBR all the way to the 6LN.

        6LN              6LR             Root             6LBR
         |                |               |                 |
         |   NS(EARO)     |               |                 |
         |--------------->|                                 |
         |                |           Extended DAR          |
         |                |-------------------------------->|
         |                |                                 |
         |                |           Extended DAC          |
         |                |<--------------------------------|
         |                |      DAO      |                 |
         |                |-------------->|                 |
         |                |               | keep-alive EDAR |
         |                |               |---------------->|
         |                |               |      EDAC       |
         |                |               |<----------------|
         |                |    DAO-ACK    |                 |
         |                |<--------------|                 |
         |   NA(EARO)     |                                 |
         |<---------------|               |                 |
         |                |               |                 |
             (in case if an Error not reported in DAO-ACK)
         |                |               |                 |
         |                |       DCO     |                 |
         |                |<--------------|                 |
         |   NA(EARO)     |               |                 |
         |<---------------|               |                 |
         |                |               |                 |

           Figure 3: First Registration Flow in Non-Storing Mode

   A re-registration is performed by the 6LN to maintain the NCE in the
   6LR alive before lifetime expires.  Upon a re-registration, as
   illustrated in Figure 4, the 6LR redistributes the Registered Address
   NS(EARO) in RPL.

   This causes the RPL DODAG Root to refresh the state in the 6LBR with
   a keep-alive EDAC message.  The keep-alive EDAC lacks the
   Registration Ownership Verifier (ROVR) information, since it is not
   present in RPL DAO messages, but the EDAC message sent in response by
   the 6LBR contains the actual value of the ROVR field for that
   registration.

Thubert & Richardson     Expires March 12, 2020                [Page 14]
Internet-Draft           Routing for RPL Leaves           September 2019

        6LN              6LR             Root             6LBR
         |                |               |                 |
         |                |               |                 |
         |   NS(EARO)     |               |                 |
         |--------------->|               |                 |
         |                |      DAO      |                 |
         |                |-------------->|                 |
         |                |               | keep-alive EDAR |
         |                |               |---------------->|
         |                |               |      EDAC       |
         |                |               |<----------------|
         |                |    DAO-ACK    |                 |
         |                |<--------------|                 |
         |   NA(EARO)     |                                 |
         |<---------------|               |                 |
         |                |               |                 |
         |                |               |                 |

           Figure 4: Next Registration Flow in Non-Storing Mode

   In case of an error on the keep-alive EDAR flow, the error SHOULD be
   returned in the DAO-ACK - if one was requested - using the mapping of
   RPL Status and 6LoWPAN Status values discussed in Section 4.

   If the Root could not return the negative Status in the DAO-ACK then
   it sends an asynchronous Destination Cleanup Object (DCO) message
   [I-D.ietf-roll-efficient-npdao] to the 6LR indicating the issue with
   the mapped Status value.  Note that if both are used in a short
   interval of time, the DAO-ACK and DCO messages are not guaranteed to
   arrive in the same order at the 6LR.  So the 6LR must still expect a
   DAO-ACK even if it received a DCO while it was waiting for an
   acknowledgement for a short period of time, but the negative status
   in the DCO supercedes a positive status in the DAO-ACK regardless of
   the order in which they are received.

   Upon the DAO-ACK - or the DCO if it arrives first - the 6LR responds
   to the RUL with a NA(EARO) and the 6LoWPAN ND Status value that is
   mapped from the RPL status in the RPL message.  An asynchronous DCO
   is also translated in an asynchronous NA(EARO) to the RUL with a
   mapped Status value.  The RPL Status values that are mapped with
   6LoWPAN ND are in the range 128 to 192 and listed in the same order
   (see Table 1).  A RPL Status Value of 128 maps to 6LoWPAN ND Status
   Code of 1 and so on.

Thubert & Richardson     Expires March 12, 2020                [Page 15]
Internet-Draft           Routing for RPL Leaves           September 2019

8.1.2.  In RPL Storing-Mode

   In Storing Mode, the DAO-ACK is optional.  When it is used, it is
   generated by the RPL parent, which does not need to wait for the
   grand-parent to send the acknowledgement.  A successful DAO-ACK is
   not a guarantee that the DAO has yet reached the Root or that the
   keep-alive EDAR has succeeded.

   If the keep alive fails, the path is cleaned up asynchronously using
   a DCO message [I-D.ietf-roll-efficient-npdao] as illustrated in
   Figure 5 and described in further details in Section 8.2.3.

   6LN             6LR             6LR            Root              6LBR
    |               |               |               |                 |
    |   NS(EARO)    |               |               |                 |
    |-------------->|               |               |                 |
    |   NA(EARO)    |               |               |                 |
    |<--------------|               |               |                 |
    |               |               |               |                 |
    |               |      DAO      |               |                 |
    |               |-------------->|               |                 |
    |               |    DAO-ACK    |               |                 |
    |               |<--------------|               |                 |
    |               |               |               |                 |
    |               |               |      DAO      |                 |
    |               |               |-------------->|                 |
    |               |               |    DAO-ACK    |                 |
    |               |               |<--------------|                 |
    |               |               |               |                 |
    |               |               |               | keep-alive EDAR |
    |               |               |               |---------------->|
    |               |               |               |   EDAC(ROVR)    |
    |               |               |               |<----------------|
    |               |               |               |                 |
                             (in case if an Error)
    |               |               |               |                 |
    |               |              DCO              |                 |
    |               |<------------------------------|                 |
    |   NA(EARO)    |               |               |                 |
    |<--------------|               |               |                 |
    |               |               |               |                 |

             Figure 5: Next Registration Flow in Storing Mode

Thubert & Richardson     Expires March 12, 2020                [Page 16]
Internet-Draft           Routing for RPL Leaves           September 2019

8.2.  Operation

8.2.1.  By the 6LN

   This specification does not alter the operation of a 6LoWPAN ND-
   compliant 6LN, and a RUL is expected to operate as follows:

   o  The 6LN obtains an IPv6 global address, for instance using
      autoconfiguration [RFC4862] based on a Prefix Information Option
      (PIO) [RFC4861] found in a Router Advertisement message or by some
      other means such as DHCPv6 [RFC3315].

   o  Once it has formed an address, the 6LN (re)registers its address
      periodically, within the Lifetime of the previous registration, as
      prescribed by [RFC6775].

   o  A 6LN acting as a RUL sets the R flag in the EARO whereas a 6LN
      acting as a RAN does not set the R flag as prescribed by [RFC8505]
      section 5.1.

   o  Upon each consecutive registration, the 6LN increases the TID
      field in the EARO, as prescribed by [RFC8505] section 5.2.

   o  The 6LN can register to more than one 6LR at the same time.  In
      that case, a same value of TID is used for each registration.

   o  The 6LN may use any of the 6LRs to which it register to forward
      its packets.  Using a 6LR to which the 6LN is not registered may
      result in packets dropped by a Source Address Validation function.

   Even without support for RPL, a RUL may be aware of opaque values to
   be provided to the routing protocol.  If the RUL has a knowledge of
   the RPL Instance the packet should be injected into, then it SHOULD
   set the Opaque field in the EARO to the RPLInstanceID, else it MUST
   leave the Opaque field to zero.  In any fashion the 6LN MUST set the
   "I" field to zero to indicate that topological information to be
   passed to a routing process as specified in [RFC8505] section 5.1.

   A RUL is not expected to produce RPL artifacts in the data packets,
   but it MAY do so. for instance, if the RUL has a minimal awareness of
   the RPL Instance and can build an RPI.  A RUL that places an RPI in a
   data packet MUST indicate the RPLInstanceID that corresponds to the
   RPL Instance the packet should be injected into.  All the flags and
   the Rank field are set to zero as specified by section 11.2 of
   [RFC6550].

Thubert & Richardson     Expires March 12, 2020                [Page 17]
Internet-Draft           Routing for RPL Leaves           September 2019

8.2.2.  By the 6LR

   Also as prescribed by [RFC8505], the 6LR generates a DAR message upon
   reception of a valid NS(EARO) message for the registration of a new
   IPv6 Address by a 6LN.  If the Duplicate Address exchange succeeds,
   then the 6LR installs a Neighbor Cache Entry (NCE).  If the R flag
   was set in the EARO of the NS message, and this 6LR can manage the
   reachability of Registered Address, then the 6LR sets the R flag in
   the EARO of the NA message that is sent in response.

   From then on, the 6LN periodically sends a new NS(EARO) to refresh
   the NCE state before the lifetime indicated in the EARO expires, with
   TID that is incremented each time till it wraps in a lollipop fashion
   (see section 5.2.1 of [RFC8505] which is fully compatible with
   section 7.2 of [RFC6550]).  As long as the R flag is set and this
   router can still manage the reachability of Registered Address, the
   6LR keeps setting the R flag in the EARO of the response NA message,
   but the exchange of Extended Duplicate Address messages is skipped.

   The Opaque field in the EARO hints the 6LR on the RPL Instance that
   should be used for the DAO advertisements, and for the forwarding of
   packets sourced at the registered address when there is no RPL Packet
   Information (RPI) in the packet, in which case the 6LR SHOULD add one
   to the packet.  if the "I" field is not zero, then the 6LR MUST
   consider that the Opaque field is zero.  If the Opaque field is not
   set to zero, then it should carry a RPLInstanceID for the Instance
   suggested by the 6LN.  If the 6LR does not participate to the
   associated Instance, then the 6LR MUST consider that the Opaque field
   is empty.  If the Opaque field is empty, the 6LR is free to use the
   default Instance (zero) for the registered address or to select an
   Instance of its choice; else, that is if the 6LR participates to the
   suggested Instance, then the 6LR SHOULD use that Instance for the
   registered address.

   Upon a successful NS/NA(EARO) exchange: if the R flag was set in the
   EARO of the NS message, then the 6LR SHOULD inject the Registered
   Address in RPL by sending a DAO message on behalf of the 6LN; else
   the 6LR MUST NOT inject the Registered Address into RPL.

   The DAO message advertising the Registered Address MUST be
   constructed as follows:

   o  The Registered Address is placed in a RPL Target Option in the DAO
      message as the Target Prefix, and the Prefix Length is set to 128;

   o  the External 'E' flag in the Transit Information Option (TIO)
      associated to the Target Option is set to indicate that the 6LR
      redistributes an external target into the RPL network.  When the

Thubert & Richardson     Expires March 12, 2020                [Page 18]
Internet-Draft           Routing for RPL Leaves           September 2019

      Root has to use an IP-in-IP [I-D.ietf-roll-useofrplinfo], then
      this flag indicates the IP-in-IP should be addressed to this node;

   o  the Path Lifetime in the TIO is computed from the Lifetime in the
      EARO Option to adapt it to the Lifetime Units used in the RPL
      operation.  Note that if the lifetime is 0, then the 6LR generates
      a No-Path DAO message that cleans up the routes down to the
      Address of the 6LN;

   o  the Path Sequence in the TIO is set to the TID value found in the
      EARO option;

   o  Additionally, in Non-Storing Mode the 6LR indicates one of its
      global IPv6 unicast addresses as the Parent Address in the TIO.

   If a DAO-ACK is not requested, or has a Status that is less than 128,
   indicating the DAO was accepted, respectively by a parent in Storing
   Mode or by the Root in non-Storing Mode,, the 6LR replies with a
   NA(EARO) to the RUL with a status of 0 (Success).

   In case of a DAO-ACK or a DCO with a status of 132 (Validation
   Requested) the 6LR challenges the 6LN for ownership of the address,
   as described in section 6.1 of [RFC8505].  If the challenge succeeds
   then the operations continue as normal.  In particular a DAO message
   is generated upon the NS(EARO) that proves the ownership of the
   address.  If the challenge failed the 6LR MUST refrain from injecting
   the address in RPL and may take actions to protect itself against DoS
   attacks by a rogue 6LN, see Section 11

   Other status values above 128 indicate that the 6LR failed to inject
   the address into the RPL network.  In that case the the 6LR MUST send
   a NA(EARO) to the RUL with the mapped Status value.  If for any other
   reason the 6LR fails to inject the address into the RPL network, the
   6LR SHOULD send a NA(EARO) to the RUL with a status of 2 (Out of
   Storage) which indicates a possibility to retry later.

   If a 6LR receives a valid NS(EARO) message with the R flag reset and
   the 6LR was redistributing the Registered Address due to previous
   NS(EARO) messages with the flag set, then it MUST stop injecting the
   address.  It is up to the Registering Node to maintain the
   corresponding route from then on, either keeping it active by sending
   further DAO messages, or destroying it using a No-Path DAO.

   Upon a DCO message indicating that the address of a RUL should be
   removed from the routing table, the 6LR issues an asynchronous
   NA(EARO) to the RUL with the mapped Status value.

Thubert & Richardson     Expires March 12, 2020                [Page 19]
Internet-Draft           Routing for RPL Leaves           September 2019

8.2.3.  By the RPL Root

   In RPL Storing Mode of Operation (MOP), the DAO message is propagated
   from child to parent all the way to the Root along the DODAG,
   populating routing state as it goes.  In Non-Storing Mode, The DAO
   message is sent directly to the RPL Root.  Upon reception of a DAO
   message, for each RPL Target option that creates or updates an
   existing RPL state:

   o  the Root notifies the 6LBR using an internal API if they are co-
      located, or performs an EDAR/EDAC exchange on behalf of the 6LR if
      they are separated.  If the Target option transports a ROVR, then
      the Root MUST use it to build a full EDAR message as the 6LR
      would.  Else, a keep-alive EDAR is used with the ROVR field set to
      zero.

   An EDAR message MUST be constructed as follows:

   o  The Target IPv6 address from in the RPL Target Option is placed in
      the Registered Address field of the EDAR message and in the Target
      field of the NS message, respectively;

   o  the Registration Lifetime is adapted from the Path Lifetime in the
      TIO by converting the Lifetime Units used in RPL into units of 60
      seconds used in the 6LoWPAN ND messages;

   o  the RPL Root indicates its own MAC Address as Source Link Layer
      Address (SLLA) in the NS(EARO);

   o  the TID value is set to the Path Sequence in the TIO and indicated
      with an ICMP code of 1 in the EDAR message;

   o  when present in the RPL Target option, the ROVR field is used as
      is in the EDAR and the ICMP Code Suffix is set to the appropriate
      value as shown in Table 4 of [RFC8505] depending on the length of
      the ROVR field.  If it is not present the ROVR field in the EDAR
      is set to zero indicating that this is a keep-alive EDAR.  The
      actual value of the ROVR for that registration is expected from
      the 6LBR in the response EDAC.

   Upon a Status value in an EDAC message that is not "Success", the
   Root SHOULD destroy the formed paths using either a DAO-ACK (in Non-
   Storing Mode) or a DCO downwards as specified in
   [I-D.ietf-roll-efficient-npdao].  Failure to destroy the former path
   would result in Stale routing state and local black holes if the
   address belongs to another party elsewhere in the network.  The RPL
   Status value that maps the 6LowpAN ND status value MUST be placed in
   the DCO.

Thubert & Richardson     Expires March 12, 2020                [Page 20]
Internet-Draft           Routing for RPL Leaves           September 2019

8.2.4.  By the 6LBR

   Upon reception of an EDAR message with the ROVR field is set to zero
   indicating a keep-alive EDAR, the 6LBR checks whether an entry exists
   for the and computes whether the TID in the DAR message is fresher
   than that in the entry as prescribed in section 4.2.1. of [RFC8505].

   If the entry does not exist, the 6LBR does not create the entry, and
   answers with a Status "Removed" in the EDAC message.

   If the entry exists but is not fresher, the 6LBR does not update the
   entry, and answers with a Status "Success" in the EDAC message.

   If the entry exists and the TID in the DAR message is fresher, the
   6LBR updates the TID in the entry, and if the lifetime of the entry
   is extended by the Registration Lifetime in the DAR message, it also
   updates the lifetime of the entry.  In that case, the 6LBR replies
   with a Status "Success" in the DAC message.

   The EDAC that is constructed is the same as if the keep-alive EDAR
   was a full EDAR, and includes the ROVR that is associated to the
   registration.

9.  Protocol Operations for Multicast Addresses

   Section 12 of [RFC6550] details the RPL support for multicast flows.
   This support is not source-specific and only operates as an extension
   to the Storing Mode of Operation for unicast packets.  Note that it
   is the RPL model that the multicast packet is passed as a Layer-2
   unicast to each if the interested children.  This remains true when
   forwarding between the 6LR and the listener 6LN.

   "Multicast Listener Discovery (MLD) for IPv6" [RFC2710] and its
   updated version "Multicast Listener Discovery Version 2 (MLDv2) for
   IPv6" [RFC3810] provide an interface for a listener to register to
   multicast flows.  MLDv2 is backwards compatible with MLD, and adds in
   particular the capability to filter the sources via black lists and
   white lists.  In the MLD model, the router is a "querier" and the
   host is a multicast listener that registers to the querier to obtain
   copies of the particular flows it is interested in.

   On the first registration, as illustrated in Figure 6, the 6LN, as an
   MLD listener, sends an unsolicited Report to the 6LR in order to
   start receiving the flow immediately.  Since multicast Layer-2
   messages are avoided, it is important that the asynchronous messages
   for unsolicited Report and Done are sent reliably, for instance using
   an Layer-2 acknoledgement, or attempted multiple times.

Thubert & Richardson     Expires March 12, 2020                [Page 21]
Internet-Draft           Routing for RPL Leaves           September 2019

   The 6LR acts as a generic MLD querier and generates a DAO for the
   multicast target.  The lifetime of the DAO is set to be in the order
   of the Query Interval, yet larger to account for variable propagation
   delays.

   The Root proxies the MLD echange as listener with the 6LBR acting as
   the querier, so as to get packets from a source external to the RPL
   domain.  Upon a DAO with a multicast target, the RPL Root checks if
   it is already registered as a listener for that address, and if not,
   it performs its own unsolicited Report for the multicast target.

        6LN                  6LR             Root                6LBR
         |                    |               |                    |
         | unsolicited Report |               |                    |
         |------------------->|               |                    |
         |     <L2 ack>       |               |                    |
         |                    | DAO           |                    |
         |                    |-------------->|                    |
         |                    |    DAO-ACK    |                    |
         |                    |<--------------|                    |
         |                    |               | <if not listening> |
         |                    |               | unsolicited Report |
         |                    |               |------------------->|
         |                    |               |                    |
         |                    |               |                    |

                Figure 6: First Multicast Registration Flow

   A re-registration is pulled by 6LR acting as querier.  Note that the
   message may sent unicast to all the known individual listeners.  Upon
   a time out of the Query Interval, the 6LR sends a Query to each of
   its listeners, and gets a Report back that is mapped into a DAO, as
   illustrated in Figure 7,

Thubert & Richardson     Expires March 12, 2020                [Page 22]
Internet-Draft           Routing for RPL Leaves           September 2019

        6LN                  6LR             Root                6LBR
         |                    |               |                    |
         |       Query        |               |                    |
         |<-------------------|               |                    |
         |       Report       |               |                    |
         |------------------->|               |                    |
         |                    | DAO           |                    |
         |                    |-------------->|                    |
         |                    |    DAO-ACK    |                    |
         |                    |<--------------|                    |
         |                    |               |                    |
         |                    |               |       Query        |
         |                    |               |<-------------------|
         |                    |               |       Report       |
         |                    |               |------------------->|
         |                    |               |                    |
         |                    |               |                    |

                     Figure 7: Next Registration Flow

   Note that any of the functions 6LR, Root and 6LBR might be collapsed
   in a single node, in which case the flow above happens internally,
   and possibly through internal API calls as opposed to messaging.

10.  Implementation Status

11.  Security Considerations

   The LLN nodes depend on the 6LBR and the RPL participants for their
   operation.  A trust model must be put in place to ensure that the
   right devices are acting in these roles, so as to avoid threats such
   as black-holing, (see [RFC7416] section 7) or bombing attack whereby
   an impersonated 6LBR would destroy state in the network by using the
   "Removed" Status code.  This trust model could be at a minimum based
   on a Layer-2 access control, or could provide role validation as
   well.  This is a generic 6LoWPAN requirement, see Req5.1 in
   Appendix of [RFC8505].

   The keep-alive EDAR message does not carry a valid Registration
   Unique ID [RFC8505] and it cannot be used to create a binding state
   in the 6LBR.  The 6LBR MUST NOT create an entry based on a keep-alive
   EDAR that does not match an existing entry.  All it can do is refresh
   the lifetime and the TID of an existing entry.

   At the time of this writing RPL does not have a zerotrust model
   whereby the it is possible to validate the origin of an address that
   is injected in a DAO.  This specification makes a first step in that

Thubert & Richardson     Expires March 12, 2020                [Page 23]
Internet-Draft           Routing for RPL Leaves           September 2019

   direction by allowing the Root to challenge the RUL by the 6LR that
   serves it.

12.  IANA Considerations

12.1.  RPL Target Option Flags

   Section 20.15 of [RFC6550] creates a registry for the 8-bit RPL
   Target Option Flags field.  This specification reduces the field to 4
   bits.  The IANA is requested to reduce the size of the registry
   accordingly.

12.2.  New Subsubregistry for the Status values of the RPL DAO-ACK
       Message

   This specification creates a new subsubregistry for the Status values
   of the RPL DAO-ACK Message, under the ICMPv6 parameters registry.

   o  Possible values are 8-bit unsigned integers (0..255).

   o  Registration procedure is "Standards Action" [RFC8126].

   o  Initial allocation is as indicated in Table 1:

Thubert & Richardson     Expires March 12, 2020                [Page 24]
Internet-Draft           Routing for RPL Leaves           September 2019

   +---------+-----------------------+---------------------------------+
   |  Value  |        Meaning        |          Defining Spec          |
   +---------+-----------------------+---------------------------------+
   |    0    |      Unqualified      |            [RFC6550]            |
   |         |       acceptance      |                                 |
   |         |                       |                                 |
   |  1-127  |  Reserved for Warning |            [RFC6550]            |
   |         |         Codes         |                                 |
   |         |                       |                                 |
   |   128   |   Duplicate Address   |             This RFC            |
   |         |                       |                                 |
   |   129   |     Out of Storage    |             This RFC            |
   |         |                       |                                 |
   |   130   |         Moved         | [I-D.ietf-roll-efficient-npdao] |
   |         |                       |                                 |
   |   131   |        Removed        |             This RFC            |
   |         |                       |                                 |
   |   132   |  Validation Requested |             This RFC            |
   |         |                       |                                 |
   |   133   |    Duplicate Source   |             This RFC            |
   |         |        Address        |                                 |
   |         |                       |                                 |
   |   134   |     Invalid Source    |             This RFC            |
   |         |        Address        |                                 |
   |         |                       |                                 |
   |   135   | Address topologically |             This RFC            |
   |         |       incorrect       |                                 |
   |         |                       |                                 |
   |   136   |     6LBR Registry     |             This RFC            |
   |         |       saturated       |                                 |
   |         |                       |                                 |
   |   137   |   Validation Failed   |             This RFC            |
   |         |                       |                                 |
   | 138-192 |  Reserved for 6LoWPAN |             This RFC            |
   |         |    ND code mapping    |                                 |
   |         |                       |                                 |
   | 193-255 |   Reserved for other  |            [RFC6550]            |
   |         |    Rejection Codes    |                                 |
   +---------+-----------------------+---------------------------------+

             Table 1: Status values of the RPL DAO-ACK Message

13.  Acknowledgments

   The authors wish to thank Georgios Papadopoulos for their early
   reviews of and contributions to this document

Thubert & Richardson     Expires March 12, 2020                [Page 25]
Internet-Draft           Routing for RPL Leaves           September 2019

14.  References

14.1.  Normative References

   [I-D.ietf-6lo-ap-nd]
              Thubert, P., Sarikaya, B., Sethi, M., and R. Struik,
              "Address Protected Neighbor Discovery for Low-power and
              Lossy Networks", draft-ietf-6lo-ap-nd-12 (work in
              progress), April 2019.

   [I-D.ietf-roll-efficient-npdao]
              Jadhav, R., Thubert, P., Sahoo, R., and Z. Cao, "Efficient
              Route Invalidation", draft-ietf-roll-efficient-npdao-16
              (work in progress), September 2019.

   [I-D.ietf-roll-useofrplinfo]
              Robles, I., Richardson, M., and P. Thubert, "Using RPL
              Option Type, Routing Header for Source Routes and IPv6-in-
              IPv6 encapsulation in the RPL Data Plane", draft-ietf-
              roll-useofrplinfo-31 (work in progress), August 2019.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC2710]  Deering, S., Fenner, W., and B. Haberman, "Multicast
              Listener Discovery (MLD) for IPv6", RFC 2710,
              DOI 10.17487/RFC2710, October 1999,
              <https://www.rfc-editor.org/info/rfc2710>.

   [RFC3810]  Vida, R., Ed. and L. Costa, Ed., "Multicast Listener
              Discovery Version 2 (MLDv2) for IPv6", RFC 3810,
              DOI 10.17487/RFC3810, June 2004,
              <https://www.rfc-editor.org/info/rfc3810>.

   [RFC4861]  Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
              "Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
              DOI 10.17487/RFC4861, September 2007,
              <https://www.rfc-editor.org/info/rfc4861>.

   [RFC4862]  Thomson, S., Narten, T., and T. Jinmei, "IPv6 Stateless
              Address Autoconfiguration", RFC 4862,
              DOI 10.17487/RFC4862, September 2007,
              <https://www.rfc-editor.org/info/rfc4862>.

Thubert & Richardson     Expires March 12, 2020                [Page 26]
Internet-Draft           Routing for RPL Leaves           September 2019

   [RFC4919]  Kushalnagar, N., Montenegro, G., and C. Schumacher, "IPv6
              over Low-Power Wireless Personal Area Networks (6LoWPANs):
              Overview, Assumptions, Problem Statement, and Goals",
              RFC 4919, DOI 10.17487/RFC4919, August 2007,
              <https://www.rfc-editor.org/info/rfc4919>.

   [RFC6550]  Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J.,
              Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur,
              JP., and R. Alexander, "RPL: IPv6 Routing Protocol for
              Low-Power and Lossy Networks", RFC 6550,
              DOI 10.17487/RFC6550, March 2012,
              <https://www.rfc-editor.org/info/rfc6550>.

   [RFC6553]  Hui, J. and JP. Vasseur, "The Routing Protocol for Low-
              Power and Lossy Networks (RPL) Option for Carrying RPL
              Information in Data-Plane Datagrams", RFC 6553,
              DOI 10.17487/RFC6553, March 2012,
              <https://www.rfc-editor.org/info/rfc6553>.

   [RFC6606]  Kim, E., Kaspar, D., Gomez, C., and C. Bormann, "Problem
              Statement and Requirements for IPv6 over Low-Power
              Wireless Personal Area Network (6LoWPAN) Routing",
              RFC 6606, DOI 10.17487/RFC6606, May 2012,
              <https://www.rfc-editor.org/info/rfc6606>.

   [RFC6775]  Shelby, Z., Ed., Chakrabarti, S., Nordmark, E., and C.
              Bormann, "Neighbor Discovery Optimization for IPv6 over
              Low-Power Wireless Personal Area Networks (6LoWPANs)",
              RFC 6775, DOI 10.17487/RFC6775, November 2012,
              <https://www.rfc-editor.org/info/rfc6775>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [RFC8138]  Thubert, P., Ed., Bormann, C., Toutain, L., and R. Cragie,
              "IPv6 over Low-Power Wireless Personal Area Network
              (6LoWPAN) Routing Header", RFC 8138, DOI 10.17487/RFC8138,
              April 2017, <https://www.rfc-editor.org/info/rfc8138>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

Thubert & Richardson     Expires March 12, 2020                [Page 27]
Internet-Draft           Routing for RPL Leaves           September 2019

   [RFC8200]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", STD 86, RFC 8200,
              DOI 10.17487/RFC8200, July 2017,
              <https://www.rfc-editor.org/info/rfc8200>.

   [RFC8505]  Thubert, P., Ed., Nordmark, E., Chakrabarti, S., and C.
              Perkins, "Registration Extensions for IPv6 over Low-Power
              Wireless Personal Area Network (6LoWPAN) Neighbor
              Discovery", RFC 8505, DOI 10.17487/RFC8505, November 2018,
              <https://www.rfc-editor.org/info/rfc8505>.

14.2.  Informative References

   [RFC3315]  Droms, R., Ed., Bound, J., Volz, B., Lemon, T., Perkins,
              C., and M. Carney, "Dynamic Host Configuration Protocol
              for IPv6 (DHCPv6)", RFC 3315, DOI 10.17487/RFC3315, July
              2003, <https://www.rfc-editor.org/info/rfc3315>.

   [RFC6282]  Hui, J., Ed. and P. Thubert, "Compression Format for IPv6
              Datagrams over IEEE 802.15.4-Based Networks", RFC 6282,
              DOI 10.17487/RFC6282, September 2011,
              <https://www.rfc-editor.org/info/rfc6282>.

   [RFC6687]  Tripathi, J., Ed., de Oliveira, J., Ed., and JP. Vasseur,
              Ed., "Performance Evaluation of the Routing Protocol for
              Low-Power and Lossy Networks (RPL)", RFC 6687,
              DOI 10.17487/RFC6687, October 2012,
              <https://www.rfc-editor.org/info/rfc6687>.

   [RFC7102]  Vasseur, JP., "Terms Used in Routing for Low-Power and
              Lossy Networks", RFC 7102, DOI 10.17487/RFC7102, January
              2014, <https://www.rfc-editor.org/info/rfc7102>.

   [RFC7228]  Bormann, C., Ersue, M., and A. Keranen, "Terminology for
              Constrained-Node Networks", RFC 7228,
              DOI 10.17487/RFC7228, May 2014,
              <https://www.rfc-editor.org/info/rfc7228>.

   [RFC7416]  Tsao, T., Alexander, R., Dohler, M., Daza, V., Lozano, A.,
              and M. Richardson, Ed., "A Security Threat Analysis for
              the Routing Protocol for Low-Power and Lossy Networks
              (RPLs)", RFC 7416, DOI 10.17487/RFC7416, January 2015,
              <https://www.rfc-editor.org/info/rfc7416>.

   [RFC8025]  Thubert, P., Ed. and R. Cragie, "IPv6 over Low-Power
              Wireless Personal Area Network (6LoWPAN) Paging Dispatch",
              RFC 8025, DOI 10.17487/RFC8025, November 2016,
              <https://www.rfc-editor.org/info/rfc8025>.

Thubert & Richardson     Expires March 12, 2020                [Page 28]
Internet-Draft           Routing for RPL Leaves           September 2019

   [RFC8504]  Chown, T., Loughney, J., and T. Winters, "IPv6 Node
              Requirements", BCP 220, RFC 8504, DOI 10.17487/RFC8504,
              January 2019, <https://www.rfc-editor.org/info/rfc8504>.

Appendix A.  Example Compression

   Figure 8 illustrates the case in Storing mode where the packet is
   received from the Internet, then the Root encapsulates the packet to
   insert the RPI and deliver to the 6LR that is the parent and last hop
   to the final destination, which is not known to support [RFC8138].
   The difference with the format presented in Figure 19 of [RFC8138] is
   the addition of a SRH-6LoRH before the RPI-6LoRH to transport the
   destination address of the outer IPv6 header.

   +-+ ... -+-+ ... +-+- ... -+-+ ... -+-+-+ ... +-+-+ ... -+ ... +-...
   |11110001|SRH-6LoRH| RPI-  |IP-in-IP| NH=1      |11110CPP| UDP | UDP
   |Page 1  |Type1 S=0| 6LoRH | 6LoRH  |LOWPAN_IPHC| UDP    | hdr |Payld
   +-+ ... -+-+ ... +-+- ... -+-+ ... -+-+-+ ... +-+-+ ... -+ ... +-...
          <-4bytes->              <-        RFC 6282      ->
                                              No RPL artifact

           Figure 8: Encapsulation to Parent 6LR in Storing Mode

   In Figure 8, the source of the IP-in-IP encapsulation is the Root, so
   it is elided in the IP-in-IP 6LoRH.  The destination is the parent
   6LR of the destination of the inner packet so it cannot be elided.
   In Storing Mode, it is placed as the single entry in an SRH-6LoRH as
   the first 6LoRH.  Since there is a single entry so the SRH-6LoRH Size
   is 0.  In this particular example, the 6LR address can be compressed
   to 2 bytes so a Type of 1 is used.  It results that the total length
   of the SRH-6LoRH is 4 bytes.

   In Non-Storing Mode, the encapsulation from the Root would be similar
   to that represented in Figure 8 with possibly more hops in the SRH-
   6LoRH and possibly multiple SRH-6LoRHs if the various addresses in
   the routing header are not compressed to the same format.  Note that
   on the last hop to the parent 6LR, the RH3 is consumed and removed
   from the compressed form, so the use of Non-Storing Mode vs.  Storing
   Mode is indistinguishable from the packet format.

   Follows the RPI-6LoRH and then the IP-in-IP 6LoRH.  When the IP-in-IP
   6LoRH is removed, all the router headers that precede it are also
   removed.

   The Paging Dispatch [RFC8025] may also be removed if there was no
   previous Page change to a Page other than 0 or 1, since the
   LOWPAN_IPHC is encoded in the same fashion in the default Page 0 and

Thubert & Richardson     Expires March 12, 2020                [Page 29]
Internet-Draft           Routing for RPL Leaves           September 2019

   in Page 1.  The resulting packet to the destination is the inner
   packet compressed with [RFC6282].

Authors' Addresses

   Pascal Thubert (editor)
   Cisco Systems, Inc
   Building D
   45 Allee des Ormes - BP1200
   MOUGINS - Sophia Antipolis  06254
   FRANCE

   Phone: +33 497 23 26 34
   Email: pthubert@cisco.com

   Michael C. Richardson
   Sandelman Software Works

   Email: mcr+ietf@sandelman.ca
   URI:   http://www.sandelman.ca/

Thubert & Richardson     Expires March 12, 2020                [Page 30]