QUIC Loss Detection and Congestion Control
draft-ietf-quic-recovery-17
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft that was ultimately published as RFC 9002.
|
|
|---|---|---|---|
| Authors | Jana Iyengar , Ian Swett | ||
| Last updated | 2018-12-18 (Latest revision 2018-10-23) | ||
| Replaces | draft-iyengar-quic-loss-recovery | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
GENART Last Call review
(of
-32)
by Vijay Gurbani
Ready w/nits
|
||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | WG Document | |
| Document shepherd | (None) | ||
| IESG | IESG state | Became RFC 9002 (Proposed Standard) | |
| Consensus boilerplate | Yes | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-quic-recovery-17
QUIC J. Iyengar, Ed.
Internet-Draft Fastly
Intended status: Standards Track I. Swett, Ed.
Expires: June 21, 2019 Google
December 18, 2018
QUIC Loss Detection and Congestion Control
draft-ietf-quic-recovery-17
Abstract
This document describes loss detection and congestion control
mechanisms for QUIC.
Note to Readers
Discussion of this draft takes place on the QUIC working group
mailing list (quic@ietf.org), which is archived at
https://mailarchive.ietf.org/arch/search/?email_list=quic [1].
Working Group information can be found at https://github.com/quicwg
[2]; source code and issues list for this draft can be found at
https://github.com/quicwg/base-drafts/labels/-recovery [3].
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at https://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on June 21, 2019.
Copyright Notice
Copyright (c) 2018 IETF Trust and the persons identified as the
document authors. All rights reserved.
Iyengar & Swett Expires June 21, 2019 [Page 1]
Internet-Draft QUIC Loss Detection December 2018
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(https://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Conventions and Definitions . . . . . . . . . . . . . . . . . 4
3. Design of the QUIC Transmission Machinery . . . . . . . . . . 4
3.1. Relevant Differences Between QUIC and TCP . . . . . . . . 5
3.1.1. Separate Packet Number Spaces . . . . . . . . . . . . 5
3.1.2. Monotonically Increasing Packet Numbers . . . . . . . 6
3.1.3. No Reneging . . . . . . . . . . . . . . . . . . . . . 6
3.1.4. More ACK Ranges . . . . . . . . . . . . . . . . . . . 6
3.1.5. Explicit Correction For Delayed ACKs . . . . . . . . 6
4. Generating Acknowledgements . . . . . . . . . . . . . . . . . 7
4.1. Crypto Handshake Data . . . . . . . . . . . . . . . . . . 7
4.2. ACK Ranges . . . . . . . . . . . . . . . . . . . . . . . 7
4.3. Receiver Tracking of ACK Frames . . . . . . . . . . . . . 8
5. Computing the RTT estimate . . . . . . . . . . . . . . . . . 8
6. Loss Detection . . . . . . . . . . . . . . . . . . . . . . . 9
6.1. Acknowledgement-based Detection . . . . . . . . . . . . . 9
6.1.1. Packet Threshold . . . . . . . . . . . . . . . . . . 9
6.1.2. Time Threshold . . . . . . . . . . . . . . . . . . . 10
6.2. Timeout Loss Detection . . . . . . . . . . . . . . . . . 10
6.2.1. Crypto Retransmission Timeout . . . . . . . . . . . . 10
6.2.2. Probe Timeout . . . . . . . . . . . . . . . . . . . . 12
6.3. Tracking Sent Packets . . . . . . . . . . . . . . . . . . 13
6.3.1. Sent Packet Fields . . . . . . . . . . . . . . . . . 14
6.4. Pseudocode . . . . . . . . . . . . . . . . . . . . . . . 14
6.4.1. Constants of interest . . . . . . . . . . . . . . . . 14
6.4.2. Variables of interest . . . . . . . . . . . . . . . . 15
6.4.3. Initialization . . . . . . . . . . . . . . . . . . . 16
6.4.4. On Sending a Packet . . . . . . . . . . . . . . . . . 16
6.4.5. On Receiving an Acknowledgment . . . . . . . . . . . 16
6.4.6. On Packet Acknowledgment . . . . . . . . . . . . . . 18
6.4.7. Setting the Loss Detection Timer . . . . . . . . . . 18
6.4.8. On Timeout . . . . . . . . . . . . . . . . . . . . . 19
6.4.9. Detecting Lost Packets . . . . . . . . . . . . . . . 20
6.5. Discussion . . . . . . . . . . . . . . . . . . . . . . . 21
7. Congestion Control . . . . . . . . . . . . . . . . . . . . . 22
7.1. Explicit Congestion Notification . . . . . . . . . . . . 22
Iyengar & Swett Expires June 21, 2019 [Page 2]
Internet-Draft QUIC Loss Detection December 2018
7.2. Slow Start . . . . . . . . . . . . . . . . . . . . . . . 22
7.3. Congestion Avoidance . . . . . . . . . . . . . . . . . . 22
7.4. Recovery Period . . . . . . . . . . . . . . . . . . . . . 23
7.5. Probe Timeout . . . . . . . . . . . . . . . . . . . . . . 23
7.6. Pacing . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.7. Sending data after an idle period . . . . . . . . . . . . 24
7.8. Discarding Packet Number Space State . . . . . . . . . . 24
7.9. Pseudocode . . . . . . . . . . . . . . . . . . . . . . . 24
7.9.1. Constants of interest . . . . . . . . . . . . . . . . 24
7.9.2. Variables of interest . . . . . . . . . . . . . . . . 25
7.9.3. Initialization . . . . . . . . . . . . . . . . . . . 26
7.9.4. On Packet Sent . . . . . . . . . . . . . . . . . . . 26
7.9.5. On Packet Acknowledgement . . . . . . . . . . . . . . 26
7.9.6. On New Congestion Event . . . . . . . . . . . . . . . 26
7.9.7. Process ECN Information . . . . . . . . . . . . . . . 27
7.9.8. On Packets Lost . . . . . . . . . . . . . . . . . . . 27
8. Security Considerations . . . . . . . . . . . . . . . . . . . 27
8.1. Congestion Signals . . . . . . . . . . . . . . . . . . . 28
8.2. Traffic Analysis . . . . . . . . . . . . . . . . . . . . 28
8.3. Misreporting ECN Markings . . . . . . . . . . . . . . . . 28
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 28
10. References . . . . . . . . . . . . . . . . . . . . . . . . . 28
10.1. Normative References . . . . . . . . . . . . . . . . . . 29
10.2. Informative References . . . . . . . . . . . . . . . . . 29
10.3. URIs . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Appendix A. Change Log . . . . . . . . . . . . . . . . . . . . . 31
A.1. Since draft-ietf-quic-recovery-16 . . . . . . . . . . . . 31
A.2. Since draft-ietf-quic-recovery-14 . . . . . . . . . . . . 32
A.3. Since draft-ietf-quic-recovery-13 . . . . . . . . . . . . 32
A.4. Since draft-ietf-quic-recovery-12 . . . . . . . . . . . . 32
A.5. Since draft-ietf-quic-recovery-11 . . . . . . . . . . . . 32
A.6. Since draft-ietf-quic-recovery-10 . . . . . . . . . . . . 32
A.7. Since draft-ietf-quic-recovery-09 . . . . . . . . . . . . 33
A.8. Since draft-ietf-quic-recovery-08 . . . . . . . . . . . . 33
A.9. Since draft-ietf-quic-recovery-07 . . . . . . . . . . . . 33
A.10. Since draft-ietf-quic-recovery-06 . . . . . . . . . . . . 33
A.11. Since draft-ietf-quic-recovery-05 . . . . . . . . . . . . 33
A.12. Since draft-ietf-quic-recovery-04 . . . . . . . . . . . . 33
A.13. Since draft-ietf-quic-recovery-03 . . . . . . . . . . . . 33
A.14. Since draft-ietf-quic-recovery-02 . . . . . . . . . . . . 33
A.15. Since draft-ietf-quic-recovery-01 . . . . . . . . . . . . 34
A.16. Since draft-ietf-quic-recovery-00 . . . . . . . . . . . . 34
A.17. Since draft-iyengar-quic-loss-recovery-01 . . . . . . . . 34
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . 34
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 34
Iyengar & Swett Expires June 21, 2019 [Page 3]
Internet-Draft QUIC Loss Detection December 2018
1. Introduction
QUIC is a new multiplexed and secure transport atop UDP. QUIC builds
on decades of transport and security experience, and implements
mechanisms that make it attractive as a modern general-purpose
transport. The QUIC protocol is described in [QUIC-TRANSPORT].
QUIC implements the spirit of known TCP loss recovery mechanisms,
described in RFCs, various Internet-drafts, and also those prevalent
in the Linux TCP implementation. This document describes QUIC
congestion control and loss recovery, and where applicable,
attributes the TCP equivalent in RFCs, Internet-drafts, academic
papers, and/or TCP implementations.
2. Conventions and Definitions
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted as described in BCP
14 [RFC2119] [RFC8174] when, and only when, they appear in all
capitals, as shown here.
Definitions of terms that are used in this document:
ACK-only: Any packet containing only one or more ACK frame(s).
In-flight: Packets are considered in-flight when they have been sent
and neither acknowledged nor declared lost, and they are not ACK-
only.
Ack-eliciting Frames: All frames besides ACK or PADDING are
considered ack-eliciting.
Ack-eliciting Packets: Packets that contain ack-eliciting frames
elicit an ACK from the receiver within the maximum ack delay and
are called ack-eliciting packets.
Crypto Packets: Packets containing CRYPTO data sent in Initial or
Handshake packets.
3. Design of the QUIC Transmission Machinery
All transmissions in QUIC are sent with a packet-level header, which
indicates the encryption level and includes a packet sequence number
(referred to below as a packet number). The encryption level
indicates the packet number space, as described in [QUIC-TRANSPORT].
Packet numbers never repeat within a packet number space for the
Iyengar & Swett Expires June 21, 2019 [Page 4]
Internet-Draft QUIC Loss Detection December 2018
lifetime of a connection. Packet numbers monotonically increase
within a space, preventing ambiguity.
This design obviates the need for disambiguating between
transmissions and retransmissions and eliminates significant
complexity from QUIC's interpretation of TCP loss detection
mechanisms.
QUIC packets can contain multiple frames of different types. The
recovery mechanisms ensure that data and frames that need reliable
delivery are acknowledged or declared lost and sent in new packets as
necessary. The types of frames contained in a packet affect recovery
and congestion control logic:
o All packets are acknowledged, though packets that contain no ack-
eliciting frames are only acknowledged along with ack-eliciting
packets.
o Long header packets that contain CRYPTO frames are critical to the
performance of the QUIC handshake and use shorter timers for
acknowledgement and retransmission.
o Packets that contain only ACK frames do not count toward
congestion control limits and are not considered in-flight. Note
that this means PADDING frames cause packets to contribute toward
bytes in flight without directly causing an acknowledgment to be
sent.
3.1. Relevant Differences Between QUIC and TCP
Readers familiar with TCP's loss detection and congestion control
will find algorithms here that parallel well-known TCP ones.
Protocol differences between QUIC and TCP however contribute to
algorithmic differences. We briefly describe these protocol
differences below.
3.1.1. Separate Packet Number Spaces
QUIC uses separate packet number spaces for each encryption level,
except 0-RTT and all generations of 1-RTT keys use the same packet
number space. Separate packet number spaces ensures acknowledgement
of packets sent with one level of encryption will not cause spurious
retransmission of packets sent with a different encryption level.
Congestion control and RTT measurement are unified across packet
number spaces.
Iyengar & Swett Expires June 21, 2019 [Page 5]
Internet-Draft QUIC Loss Detection December 2018
3.1.2. Monotonically Increasing Packet Numbers
TCP conflates transmission order at the sender with delivery order at
the receiver, which results in retransmissions of the same data
carrying the same sequence number, and consequently leads to
"retransmission ambiguity". QUIC separates the two: QUIC uses a
packet number to indicate transmission order, and any application
data is sent in one or more streams, with delivery order determined
by stream offsets encoded within STREAM frames.
QUIC's packet number is strictly increasing within a packet number
space, and directly encodes transmission order. A higher packet
number signifies that the packet was sent later, and a lower packet
number signifies that the packet was sent earlier. When a packet
containing ack-eliciting frames is detected lost, QUIC rebundles
necessary frames in a new packet with a new packet number, removing
ambiguity about which packet is acknowledged when an ACK is received.
Consequently, more accurate RTT measurements can be made, spurious
retransmissions are trivially detected, and mechanisms such as Fast
Retransmit can be applied universally, based only on packet number.
This design point significantly simplifies loss detection mechanisms
for QUIC. Most TCP mechanisms implicitly attempt to infer
transmission ordering based on TCP sequence numbers - a non-trivial
task, especially when TCP timestamps are not available.
3.1.3. No Reneging
QUIC ACKs contain information that is similar to TCP SACK, but QUIC
does not allow any acked packet to be reneged, greatly simplifying
implementations on both sides and reducing memory pressure on the
sender.
3.1.4. More ACK Ranges
QUIC supports many ACK ranges, opposed to TCP's 3 SACK ranges. In
high loss environments, this speeds recovery, reduces spurious
retransmits, and ensures forward progress without relying on
timeouts.
3.1.5. Explicit Correction For Delayed ACKs
QUIC ACKs explicitly encode the delay incurred at the receiver
between when a packet is received and when the corresponding ACK is
sent. This allows the receiver of the ACK to adjust for receiver
delays, specifically the delayed ack timer, when estimating the path
RTT. This mechanism also allows a receiver to measure and report the
delay from when a packet was received by the OS kernel, which is
Iyengar & Swett Expires June 21, 2019 [Page 6]
Internet-Draft QUIC Loss Detection December 2018
useful in receivers which may incur delays such as context-switch
latency before a userspace QUIC receiver processes a received packet.
4. Generating Acknowledgements
QUIC SHOULD delay sending acknowledgements in response to packets,
but MUST NOT excessively delay acknowledgements of ack-eliciting
packets. Specifically, implementations MUST attempt to enforce a
maximum ack delay to avoid causing the peer spurious timeouts. The
maximum ack delay is communicated in the "max_ack_delay" transport
parameter and the default value is 25ms.
An acknowledgement SHOULD be sent immediately upon receipt of a
second packet but the delay SHOULD NOT exceed the maximum ack delay.
QUIC recovery algorithms do not assume the peer generates an
acknowledgement immediately when receiving a second full-packet.
Out-of-order packets SHOULD be acknowledged more quickly, in order to
accelerate loss recovery. The receiver SHOULD send an immediate ACK
when it receives a new packet which is not one greater than the
largest received packet number.
Similarly, packets marked with the ECN Congestion Experienced (CE)
codepoint in the IP header SHOULD be acknowledged immediately, to
reduce the peer's response time to congestion events.
As an optimization, a receiver MAY process multiple packets before
sending any ACK frames in response. In this case they can determine
whether an immediate or delayed acknowledgement should be generated
after processing incoming packets.
4.1. Crypto Handshake Data
In order to quickly complete the handshake and avoid spurious
retransmissions due to crypto retransmission timeouts, crypto packets
SHOULD use a very short ack delay, such as 1ms. ACK frames MAY be
sent immediately when the crypto stack indicates all data for that
packet number space has been received.
4.2. ACK Ranges
When an ACK frame is sent, one or more ranges of acknowledged packets
are included. Including older packets reduces the chance of spurious
retransmits caused by losing previously sent ACK frames, at the cost
of larger ACK frames.
ACK frames SHOULD always acknowledge the most recently received
packets, and the more out-of-order the packets are, the more
Iyengar & Swett Expires June 21, 2019 [Page 7]
Internet-Draft QUIC Loss Detection December 2018
important it is to send an updated ACK frame quickly, to prevent the
peer from declaring a packet as lost and spuriously retransmitting
the frames it contains.
Below is one recommended approach for determining what packets to
include in an ACK frame.
4.3. Receiver Tracking of ACK Frames
When a packet containing an ACK frame is sent, the largest
acknowledged in that frame may be saved. When a packet containing an
ACK frame is acknowledged, the receiver can stop acknowledging
packets less than or equal to the largest acknowledged in the sent
ACK frame.
In cases without ACK frame loss, this algorithm allows for a minimum
of 1 RTT of reordering. In cases with ACK frame loss and reordering,
this approach does not guarantee that every acknowledgement is seen
by the sender before it is no longer included in the ACK frame.
Packets could be received out of order and all subsequent ACK frames
containing them could be lost. In this case, the loss recovery
algorithm may cause spurious retransmits, but the sender will
continue making forward progress.
5. Computing the RTT estimate
RTT is calculated when an ACK frame arrives by computing the
difference between the current time and the time the largest acked
packet was sent. An RTT sample MUST NOT be taken for a packet that
is not newly acknowledged or not ack-eliciting.
When RTT is calculated, the ack delay field from the ACK frame SHOULD
be limited to the max_ack_delay specified by the peer. Limiting
ack_delay to max_ack_delay ensures a peer specifying an extremely
small max_ack_delay doesn't cause more spurious timeouts than a peer
that correctly specifies max_ack_delay. It SHOULD be subtracted from
the RTT as long as the result is larger than the min_rtt. If the
result is smaller than the min_rtt, the RTT should be used, but the
ack delay field should be ignored.
Like TCP, QUIC calculates both smoothed RTT and RTT variance similar
to those specified in [RFC6298].
min_rtt is the minimum RTT measured over the connection, prior to
adjusting by ack delay. Ignoring ack delay for min RTT prevents
intentional or unintentional underestimation of min RTT, which in
turn prevents underestimating smoothed RTT.
Iyengar & Swett Expires June 21, 2019 [Page 8]
Internet-Draft QUIC Loss Detection December 2018
6. Loss Detection
QUIC senders use both ack information and timeouts to detect lost
packets, and this section provides a description of these algorithms.
Estimating the network round-trip time (RTT) is critical to these
algorithms and is described first.
If a packet is lost, the QUIC transport needs to recover from that
loss, such as by retransmitting the data, sending an updated frame,
or abandoning the frame. For more information, see Section 13.2 of
[QUIC-TRANSPORT].
6.1. Acknowledgement-based Detection
Acknowledgement-based loss detection implements the spirit of TCP's
Fast Retransmit [RFC5681], Early Retransmit [RFC5827], FACK [FACK],
SACK loss recovery [RFC6675], and RACK [RACK]. This section provides
an overview of how these algorithms are implemented in QUIC.
A packet is declared lost if it meets all the following conditions:
o The packet is unacknowledged, in-flight, and was sent prior to an
acknowledged packet.
o Either its packet number is kPacketThreshold smaller than an
acknowledged packet (Section 6.1.1), or it was sent long enough in
the past (Section 6.1.2).
The acknowledgement indicates that a packet sent later was delivered,
while the packet and time thresholds provide some tolerance for
packet reordering.
Spuriously declaring packets as lost leads to unnecessary
retransmissions and may result in degraded performance due to the
actions of the congestion controller upon detecting loss.
Implementations that detect spurious retransmissions and increase the
reordering threshold in packets or time MAY choose to start with
smaller initial reordering thresholds to minimize recovery latency.
6.1.1. Packet Threshold
The RECOMMENDED initial value for the packet reordering threshold
(kPacketThreshold) is 3, based on best practices for TCP loss
detection [RFC5681] [RFC6675].
Some networks may exhibit higher degrees of reordering, causing a
sender to detect spurious losses. Implementers MAY use algorithms
Iyengar & Swett Expires June 21, 2019 [Page 9]
Internet-Draft QUIC Loss Detection December 2018
developed for TCP, such as TCP-NCR [RFC4653], to improve QUIC's
reordering resilience.
6.1.2. Time Threshold
Once a later packet has been acknowledged, an endpoint SHOULD declare
an earlier packet lost if it was sent a threshold amount of time in
the past. The time threshold is computed as kTimeThreshold *
max(SRTT, latest_RTT). If packets sent prior to the largest
acknowledged packet cannot yet be declared lost, then a timer SHOULD
be set for the remaining time.
The RECOMMENDED time threshold (kTimeThreshold), expressed as a
round-trip time multiplier, is 9/8.
Using max(SRTT, latest_RTT) protects from the two following cases:
o the latest RTT sample is lower than the SRTT, perhaps due to
reordering where packet whose ack triggered the Early Retransmit
process encountered a shorter path;
o the latest RTT sample is higher than the SRTT, perhaps due to a
sustained increase in the actual RTT, but the smoothed SRTT has
not yet caught up.
Implementers MAY experiment with using other reordering thresholds,
including absolute thresholds, bearing in mind that a lower
multiplier reduces reordering resilience and increases spurious
retransmissions, and a higher multiplier increases loss detection
delay.
6.2. Timeout Loss Detection
Timeout loss detection recovers from losses that cannot be handled by
acknowledgement-based loss detection. It uses a single timer which
switches between a crypto retransmission timer and a probe timer.
6.2.1. Crypto Retransmission Timeout
Data in CRYPTO frames is critical to QUIC transport and crypto
negotiation, so a more aggressive timeout is used to retransmit it.
The initial crypto retransmission timeout SHOULD be set to twice the
initial RTT.
At the beginning, there are no prior RTT samples within a connection.
Resumed connections over the same network SHOULD use the previous
connection's final smoothed RTT value as the resumed connection's
Iyengar & Swett Expires June 21, 2019 [Page 10]
Internet-Draft QUIC Loss Detection December 2018
initial RTT. If no previous RTT is available, or if the network
changes, the initial RTT SHOULD be set to 100ms. When an
acknowledgement is received, a new RTT is computed and the timer
SHOULD be set for twice the newly computed smoothed RTT.
When crypto packets are sent, the sender MUST set a timer for the
crypto timeout period. Upon timeout, the sender MUST retransmit all
unacknowledged CRYPTO data if possible.
Until the server has validated the client's address on the path, the
amount of data it can send is limited, as specified in
[QUIC-TRANSPORT]. If not all unacknowledged CRYPTO data can be sent,
then all unacknowledged CRYPTO data sent in Initial packets should be
retransmitted. If no data can be sent, then no alarm should be armed
until data has been received from the client.
Because the server could be blocked until more packets are received,
the client MUST start the crypto retransmission timer even if there
is no unacknowledged CRYPTO data. If the timer expires and the
client has no CRYPTO data to retransmit and does not have Handshake
keys, it SHOULD send an Initial packet in a UDP datagram of at least
1200 bytes. If the client has Handshake keys, it SHOULD send a
Handshake packet.
On each consecutive expiration of the crypto timer without receiving
an acknowledgement for a new packet, the sender SHOULD double the
crypto retransmission timeout and set a timer for this period.
When crypto packets are in flight, the probe timer (Section 6.2.2) is
not active.
6.2.1.1. Retry and Version Negotiation
A Retry or Version Negotiation packet causes a client to send another
Initial packet, effectively restarting the connection process and
resetting congestion control and loss recovery state, including
resetting any pending timers. Either packet indicates that the
Initial was received but not processed. Neither packet can be
treated as an acknowledgment for the Initial.
6.2.1.2. Discarding Initial State
As described in Section 17.5.1 of [QUIC-TRANSPORT], endpoints stop
sending and receiving Initial packets once they start exchanging
Handshake packets. At this point, all loss recovery state for the
Initial packet number space is also discarded. Packets that are in
flight for the packet number space are not declared as either
Iyengar & Swett Expires June 21, 2019 [Page 11]
Internet-Draft QUIC Loss Detection December 2018
acknowledged or lost. After discarding state, new Initial packets
will not be sent.
The client MAY however compute an RTT estimate to the server as the
time period from when the first Initial was sent to when a Retry or a
Version Negotiation packet is received. The client MAY use this
value to seed the RTT estimator for a subsequent connection attempt
to the server.
6.2.2. Probe Timeout
A Probe Timeout (PTO) triggers a probe packet when ack-eliciting data
is in flight but an acknowledgement is not received within the
expected period of time. A PTO enables a connection to recover from
loss of tail packets or acks. The PTO algorithm used in QUIC
implements the reliability functions of Tail Loss Probe [TLP] [RACK],
RTO [RFC5681] and F-RTO algorithms for TCP [RFC5682], and the timeout
computation is based on TCP's retransmission timeout period
[RFC6298].
6.2.2.1. Computing PTO
When an ack-eliciting packet is transmitted, the sender schedules a
timer for the PTO period as follows:
PTO = max(smoothed_rtt + 4*rttvar + max_ack_delay, kGranularity)
kGranularity, smoothed_rtt, rttvar, and max_ack_delay are defined in
Section 6.4.1 and Section 6.4.2.
The PTO period is the amount of time that a sender ought to wait for
an acknowledgement of a sent packet. This time period includes the
estimated network roundtrip-time (smoothed_rtt), the variance in the
estimate (4*rttvar), and max_ack_delay, to account for the maximum
time by which a receiver might delay sending an acknowledgement.
The PTO value MUST be set to at least kGranularity, to avoid the
timer expiring immediately.
When a PTO timer expires, the PTO period MUST be set to twice its
current value. This exponential reduction in the sender's rate is
important because the PTOs might be caused by loss of packets or
acknowledgements due to severe congestion.
A sender computes its PTO timer every time an ack-eliciting packet is
sent. A sender might choose to optimize this by setting the timer
fewer times if it knows that more ack-eliciting packets will be sent
within a short period of time.
Iyengar & Swett Expires June 21, 2019 [Page 12]
Internet-Draft QUIC Loss Detection December 2018
6.2.2.2. Sending Probe Packets
When a PTO timer expires, the sender MUST send one ack-eliciting
packet as a probe. A sender MAY send up to two ack-eliciting
packets, to avoid an expensive consecutive PTO expiration due to a
single packet loss.
Consecutive PTO periods increase exponentially, and as a result,
connection recovery latency increases exponentially as packets
continue to be dropped in the network. Sending two packets on PTO
expiration increases resilience to packet drops, thus reducing the
probability of consecutive PTO events.
Probe packets sent on a PTO MUST be ack-eliciting. A probe packet
SHOULD carry new data when possible. A probe packet MAY carry
retransmitted unacknowledged data when new data is unavailable, when
flow control does not permit new data to be sent, or to
opportunistically reduce loss recovery delay. Implementations MAY
use alternate strategies for determining the content of probe
packets, including sending new or retransmitted data based on the
application's priorities.
6.2.2.3. Loss Detection
Delivery or loss of packets in flight is established when an ACK
frame is received that newly acknowledges one or more packets.
A PTO timer expiration event does not indicate packet loss and MUST
NOT cause prior unacknowledged packets to be marked as lost. After a
PTO timer has expired, an endpoint uses the following rules to mark
packets as lost when an acknowledgement is received that newly
acknowledges packets.
When an acknowledgement is received that newly acknowledges packets,
loss detection proceeds as dictated by packet and time threshold
mechanisms, see Section 6.1.
6.3. Tracking Sent Packets
To correctly implement congestion control, a QUIC sender tracks every
ack-eliciting packet until the packet is acknowledged or lost. It is
expected that implementations will be able to access this information
by packet number and crypto context and store the per-packet fields
(Section 6.3.1) for loss recovery and congestion control.
After a packet is declared lost, it SHOULD be tracked for an amount
of time comparable to the maximum expected packet reordering, such as
1 RTT. This allows for detection of spurious retransmissions.
Iyengar & Swett Expires June 21, 2019 [Page 13]
Internet-Draft QUIC Loss Detection December 2018
Sent packets are tracked for each packet number space, and ACK
processing only applies to a single space.
6.3.1. Sent Packet Fields
packet_number: The packet number of the sent packet.
ack_eliciting: A boolean that indicates whether a packet is ack-
eliciting. If true, it is expected that an acknowledgement will
be received, though the peer could delay sending the ACK frame
containing it by up to the MaxAckDelay.
in_flight: A boolean that indicates whether the packet counts
towards bytes in flight.
is_crypto_packet: A boolean that indicates whether the packet
contains cryptographic handshake messages critical to the
completion of the QUIC handshake. In this version of QUIC, this
includes any packet with the long header that includes a CRYPTO
frame.
sent_bytes: The number of bytes sent in the packet, not including
UDP or IP overhead, but including QUIC framing overhead.
time_sent: The time the packet was sent.
6.4. Pseudocode
6.4.1. Constants of interest
Constants used in loss recovery are based on a combination of RFCs,
papers, and common practice. Some may need to be changed or
negotiated in order to better suit a variety of environments.
kPacketThreshold: Maximum reordering in packets before packet
threshold loss detection considers a packet lost. The RECOMMENDED
value is 3.
kTimeThreshold: Maximum reordering in time before time threshold
loss detection considers a packet lost. Specified as an RTT
multiplier. The RECOMMENDED value is 9/8.
kGranularity: Timer granularity. This is a system-dependent value.
However, implementations SHOULD use a value no smaller than 1ms.
kInitialRtt: The RTT used before an RTT sample is taken. The
RECOMMENDED value is 100ms.
Iyengar & Swett Expires June 21, 2019 [Page 14]
Internet-Draft QUIC Loss Detection December 2018
6.4.2. Variables of interest
Variables required to implement the congestion control mechanisms are
described in this section.
loss_detection_timer: Multi-modal timer used for loss detection.
crypto_count: The number of times all unacknowledged CRYPTO data has
been retransmitted without receiving an ack.
pto_count: The number of times a PTO has been sent without receiving
an ack.
time_of_last_sent_ack_eliciting_packet: The time the most recent
ack-eliciting packet was sent.
time_of_last_sent_crypto_packet: The time the most recent crypto
packet was sent.
largest_sent_packet: The packet number of the most recently sent
packet.
largest_acked_packet: The largest packet number acknowledged in the
packet number space so far.
latest_rtt: The most recent RTT measurement made when receiving an
ack for a previously unacked packet.
smoothed_rtt: The smoothed RTT of the connection, computed as
described in [RFC6298]
rttvar: The RTT variance, computed as described in [RFC6298]
min_rtt: The minimum RTT seen in the connection, ignoring ack delay.
max_ack_delay: The maximum amount of time by which the receiver
intends to delay acknowledgments, in milliseconds. The actual
ack_delay in a received ACK frame may be larger due to late
timers, reordering, or lost ACKs.
loss_time: The time at which the next packet will be considered lost
based on early transmit or exceeding the reordering window in
time.
sent_packets: An association of packet numbers to information about
them. Described in detail above in Section 6.3.
Iyengar & Swett Expires June 21, 2019 [Page 15]
Internet-Draft QUIC Loss Detection December 2018
6.4.3. Initialization
At the beginning of the connection, initialize the loss detection
variables as follows:
loss_detection_timer.reset()
crypto_count = 0
pto_count = 0
loss_time = 0
smoothed_rtt = 0
rttvar = 0
min_rtt = infinite
time_of_last_sent_ack_eliciting_packet = 0
time_of_last_sent_crypto_packet = 0
largest_sent_packet = 0
largest_acked_packet = 0
6.4.4. On Sending a Packet
After a packet is sent, information about the packet is stored. The
parameters to OnPacketSent are described in detail above in
Section 6.3.1.
Pseudocode for OnPacketSent follows:
OnPacketSent(packet_number, ack_eliciting, in_flight,
is_crypto_packet, sent_bytes):
largest_sent_packet = packet_number
sent_packets[packet_number].packet_number = packet_number
sent_packets[packet_number].time_sent = now
sent_packets[packet_number].ack_eliciting = ack_eliciting
sent_packets[packet_number].in_flight = in_flight
if (ack_eliciting):
if (is_crypto_packet):
time_of_last_sent_crypto_packet = now
time_of_last_sent_ack_eliciting_packet = now
OnPacketSentCC(sent_bytes)
sent_packets[packet_number].size = sent_bytes
SetLossDetectionTimer()
6.4.5. On Receiving an Acknowledgment
When an ACK frame is received, it may newly acknowledge any number of
packets.
Pseudocode for OnAckReceived and UpdateRtt follow:
Iyengar & Swett Expires June 21, 2019 [Page 16]
Internet-Draft QUIC Loss Detection December 2018
OnAckReceived(ack):
largest_acked_packet = max(largest_acked_packet,
ack.largest_acked)
// If the largest acknowledged is newly acked and
// ack-eliciting, update the RTT.
if (sent_packets[ack.largest_acked] &&
sent_packets[ack.largest_acked].ack_eliciting):
latest_rtt =
now - sent_packets[ack.largest_acked].time_sent
UpdateRtt(latest_rtt, ack.ack_delay)
// Process ECN information if present.
if (ACK frame contains ECN information):
ProcessECN(ack)
// Find all newly acked packets in this ACK frame
newly_acked_packets = DetermineNewlyAckedPackets(ack)
if (newly_acked_packets.empty()):
return
for acked_packet in newly_acked_packets:
OnPacketAcked(acked_packet.packet_number)
crypto_count = 0
pto_count = 0
DetectLostPackets()
SetLossDetectionTimer()
UpdateRtt(latest_rtt, ack_delay):
// min_rtt ignores ack delay.
min_rtt = min(min_rtt, latest_rtt)
// Limit ack_delay by max_ack_delay
ack_delay = min(ack_delay, max_ack_delay)
// Adjust for ack delay if it's plausible.
if (latest_rtt - min_rtt > ack_delay):
latest_rtt -= ack_delay
// Based on {{RFC6298}}.
if (smoothed_rtt == 0):
smoothed_rtt = latest_rtt
rttvar = latest_rtt / 2
else:
rttvar_sample = abs(smoothed_rtt - latest_rtt)
rttvar = 3/4 * rttvar + 1/4 * rttvar_sample
smoothed_rtt = 7/8 * smoothed_rtt + 1/8 * latest_rtt
Iyengar & Swett Expires June 21, 2019 [Page 17]
Internet-Draft QUIC Loss Detection December 2018
6.4.6. On Packet Acknowledgment
When a packet is acknowledged for the first time, the following
OnPacketAcked function is called. Note that a single ACK frame may
newly acknowledge several packets. OnPacketAcked must be called once
for each of these newly acknowledged packets.
OnPacketAcked takes one parameter, acked_packet, which is the struct
detailed in Section 6.3.1.
Pseudocode for OnPacketAcked follows:
OnPacketAcked(acked_packet):
if (acked_packet.ack_eliciting):
OnPacketAckedCC(acked_packet)
sent_packets.remove(acked_packet.packet_number)
6.4.7. Setting the Loss Detection Timer
QUIC loss detection uses a single timer for all timeout loss
detection. The duration of the timer is based on the timer's mode,
which is set in the packet and timer events further below. The
function SetLossDetectionTimer defined below shows how the single
timer is set.
This algorithm may result in the timer being set in the past,
particularly if timers wake up late. Timers set in the past SHOULD
fire immediately.
Pseudocode for SetLossDetectionTimer follows:
Iyengar & Swett Expires June 21, 2019 [Page 18]
Internet-Draft QUIC Loss Detection December 2018
SetLossDetectionTimer():
// Don't arm timer if there are no ack-eliciting packets
// in flight.
if (no ack-eliciting packets in flight):
loss_detection_timer.cancel()
return
if (crypto packets are in flight):
// Crypto retransmission timer.
if (smoothed_rtt == 0):
timeout = 2 * kInitialRtt
else:
timeout = 2 * smoothed_rtt
timeout = max(timeout, kGranularity)
timeout = timeout * (2 ^ crypto_count)
loss_detection_timer.set(
time_of_last_sent_crypto_packet + timeout)
return
if (loss_time != 0):
// Time threshold loss detection.
loss_detection_timer.set(loss_time)
return
// Calculate PTO duration
timeout =
smoothed_rtt + 4 * rttvar + max_ack_delay
timeout = max(timeout, kGranularity)
timeout = timeout * (2 ^ pto_count)
loss_detection_timer.set(
time_of_last_sent_ack_eliciting_packet + timeout)
6.4.8. On Timeout
When the loss detection timer expires, the timer's mode determines
the action to be performed.
Pseudocode for OnLossDetectionTimeout follows:
Iyengar & Swett Expires June 21, 2019 [Page 19]
Internet-Draft QUIC Loss Detection December 2018
OnLossDetectionTimeout():
if (crypto packets are in flight):
// Crypto retransmission timeout.
RetransmitUnackedCryptoData()
crypto_count++
else if (loss_time != 0):
// Time threshold loss Detection
DetectLostPackets()
else:
// PTO
SendTwoPackets()
pto_count++
SetLossDetectionTimer()
6.4.9. Detecting Lost Packets
DetectLostPackets is called every time an ACK is received and
operates on the sent_packets for that packet number space. If the
loss detection timer expires and the loss_time is set, the previous
largest acknowledged packet is supplied.
Pseudocode for DetectLostPackets follows:
Iyengar & Swett Expires June 21, 2019 [Page 20]
Internet-Draft QUIC Loss Detection December 2018
DetectLostPackets():
loss_time = 0
lost_packets = {}
loss_delay = kTimeThreshold * max(latest_rtt, smoothed_rtt)
// Packets sent before this time are deemed lost.
lost_send_time = now() - loss_delay
// Packets with packet numbers before this are deemed lost.
lost_pn = largest_acked_packet - kPacketThreshold
foreach unacked in sent_packets:
if (unacked.packet_number > largest_acked_packet):
continue
// Mark packet as lost, or set time when it should be marked.
if (unacked.time_sent <= lost_send_time ||
unacked.packet_number <= lost_pn):
sent_packets.remove(unacked.packet_number)
if (unacked.in_flight):
lost_packets.insert(unacked)
else if (loss_time == 0):
loss_time = unacked.time_sent + loss_delay
else:
loss_time = min(loss_time, unacked.time_sent + loss_delay)
// Inform the congestion controller of lost packets and
// let it decide whether to retransmit immediately.
if (!lost_packets.empty()):
OnPacketsLost(lost_packets)
6.5. Discussion
The majority of constants were derived from best common practices
among widely deployed TCP implementations on the internet.
Exceptions follow.
A shorter delayed ack time of 25ms was chosen because longer delayed
acks can delay loss recovery and for the small number of connections
where less than packet per 25ms is delivered, acking every packet is
beneficial to congestion control and loss recovery.
The default initial RTT of 100ms was chosen because it is slightly
higher than both the median and mean min_rtt typically observed on
the public internet.
Iyengar & Swett Expires June 21, 2019 [Page 21]
Internet-Draft QUIC Loss Detection December 2018
7. Congestion Control
QUIC's congestion control is based on TCP NewReno [RFC6582]. NewReno
is a congestion window based congestion control. QUIC specifies the
congestion window in bytes rather than packets due to finer control
and the ease of appropriate byte counting [RFC3465].
QUIC hosts MUST NOT send packets if they would increase
bytes_in_flight (defined in Section 7.9.2) beyond the available
congestion window, unless the packet is a probe packet sent after a
PTO timer expires, as described in Section 6.2.2.
Implementations MAY use other congestion control algorithms, such as
Cubic [RFC8312], and endpoints MAY use different algorithms from one
another. The signals QUIC provides for congestion control are
generic and are designed to support different algorithms.
7.1. Explicit Congestion Notification
If a path has been verified to support ECN, QUIC treats a Congestion
Experienced codepoint in the IP header as a signal of congestion.
This document specifies an endpoint's response when its peer receives
packets with the Congestion Experienced codepoint. As discussed in
[RFC8311], endpoints are permitted to experiment with other response
functions.
7.2. Slow Start
QUIC begins every connection in slow start and exits slow start upon
loss or upon increase in the ECN-CE counter. QUIC re-enters slow
start anytime the congestion window is less than ssthresh, which
typically only occurs after an PTO. While in slow start, QUIC
increases the congestion window by the number of bytes acknowledged
when each acknowledgment is processed.
7.3. Congestion Avoidance
Slow start exits to congestion avoidance. Congestion avoidance in
NewReno uses an additive increase multiplicative decrease (AIMD)
approach that increases the congestion window by one maximum packet
size per congestion window acknowledged. When a loss is detected,
NewReno halves the congestion window and sets the slow start
threshold to the new congestion window.
Iyengar & Swett Expires June 21, 2019 [Page 22]
Internet-Draft QUIC Loss Detection December 2018
7.4. Recovery Period
Recovery is a period of time beginning with detection of a lost
packet or an increase in the ECN-CE counter. Because QUIC does not
retransmit packets, it defines the end of recovery as a packet sent
after the start of recovery being acknowledged. This is slightly
different from TCP's definition of recovery, which ends when the lost
packet that started recovery is acknowledged.
The recovery period limits congestion window reduction to once per
round trip. During recovery, the congestion window remains unchanged
irrespective of new losses or increases in the ECN-CE counter.
7.5. Probe Timeout
Probe packets MUST NOT be blocked by the congestion controller. A
sender MUST however count these packets as being additionally in
flight, since these packets adds network load without establishing
packet loss. Note that sending probe packets might cause the
sender's bytes in flight to exceed the congestion window until an
acknowledgement is received that establishes loss or delivery of
packets.
If a threshold number of consecutive PTOs have occurred (pto_count is
more than kPersistentCongestionThreshold, see Section 7.9.1), the
network is considered to be experiencing persistent congestion, and
the sender's congestion window MUST be reduced to the minimum
congestion window.
7.6. Pacing
This document does not specify a pacer, but it is RECOMMENDED that a
sender pace sending of all in-flight packets based on input from the
congestion controller. For example, a pacer might distribute the
congestion window over the SRTT when used with a window-based
controller, and a pacer might use the rate estimate of a rate-based
controller.
An implementation should take care to architect its congestion
controller to work well with a pacer. For instance, a pacer might
wrap the congestion controller and control the availability of the
congestion window, or a pacer might pace out packets handed to it by
the congestion controller. Timely delivery of ACK frames is
important for efficient loss recovery. Packets containing only ACK
frames should therefore not be paced, to avoid delaying their
delivery to the peer.
Iyengar & Swett Expires June 21, 2019 [Page 23]
Internet-Draft QUIC Loss Detection December 2018
As an example of a well-known and publicly available implementation
of a flow pacer, implementers are referred to the Fair Queue packet
scheduler (fq qdisc) in Linux (3.11 onwards).
7.7. Sending data after an idle period
A sender becomes idle if it ceases to send data and has no bytes in
flight. A sender's congestion window MUST not increase while it is
idle.
When sending data after becoming idle, a sender MUST reset its
congestion window to the initial congestion window (see Section 4.1
of [RFC5681]), unless it paces the sending of packets. A sender MAY
retain its congestion window if it paces the sending of any packets
in excess of the initial congestion window.
A sender MAY implement alternate mechanisms to update its congestion
window after idle periods, such as those proposed for TCP in
[RFC7661].
7.8. Discarding Packet Number Space State
When keys for an packet number space are discarded, any packets sent
with those keys are removed from the count of bytes in flight. No
loss events will occur any in-flight packets from that space, as a
result of discarding loss recovery state (see Section 6.2.1.2). Note
that it is expected that keys are discarded after those packets would
be declared lost, but Initial secrets are destroyed earlier.
7.9. Pseudocode
7.9.1. Constants of interest
Constants used in congestion control are based on a combination of
RFCs, papers, and common practice. Some may need to be changed or
negotiated in order to better suit a variety of environments.
kMaxDatagramSize: The sender's maximum payload size. Does not
include UDP or IP overhead. The max packet size is used for
calculating initial and minimum congestion windows. The
RECOMMENDED value is 1200 bytes.
kInitialWindow: Default limit on the initial amount of data in
flight, in bytes. Taken from [RFC6928]. The RECOMMENDED value is
the minimum of 10 * kMaxDatagramSize and max(2* kMaxDatagramSize,
14600)).
Iyengar & Swett Expires June 21, 2019 [Page 24]
Internet-Draft QUIC Loss Detection December 2018
kMinimumWindow: Minimum congestion window in bytes. The RECOMMENDED
value is 2 * kMaxDatagramSize.
kLossReductionFactor: Reduction in congestion window when a new loss
event is detected. The RECOMMENDED value is 0.5.
kPersistentCongestionThreshold: Number of consecutive PTOs after
which network is considered to be experiencing persistent
congestion. The rationale for this threshold is to enable a
sender to use initial PTOs for aggressive probing, similar to Tail
Loss Probe (TLP) in TCP [TLP] [RACK]. Once the number of
consecutive PTOs reaches this threshold - that is, persistent
congestion is established - the sender responds by collapsing its
congestion window to kMinimumWindow, similar to a Retransmission
Timeout (RTO) in TCP [RFC5681]. The RECOMMENDED value for
kPersistentCongestionThreshold is 2, which is equivalent to having
two TLPs before an RTO in TCP.
7.9.2. Variables of interest
Variables required to implement the congestion control mechanisms are
described in this section.
ecn_ce_counter: The highest value reported for the ECN-CE counter by
the peer in an ACK frame. This variable is used to detect
increases in the reported ECN-CE counter.
bytes_in_flight: The sum of the size in bytes of all sent packets
that contain at least one ack-eliciting or PADDING frame, and have
not been acked or declared lost. The size does not include IP or
UDP overhead, but does include the QUIC header and AEAD overhead.
Packets only containing ACK frames do not count towards
bytes_in_flight to ensure congestion control does not impede
congestion feedback.
congestion_window: Maximum number of bytes-in-flight that may be
sent.
recovery_start_time: The time when QUIC first detects a loss,
causing it to enter recovery. When a packet sent after this time
is acknowledged, QUIC exits recovery.
ssthresh: Slow start threshold in bytes. When the congestion window
is below ssthresh, the mode is slow start and the window grows by
the number of bytes acknowledged.
Iyengar & Swett Expires June 21, 2019 [Page 25]
Internet-Draft QUIC Loss Detection December 2018
7.9.3. Initialization
At the beginning of the connection, initialize the congestion control
variables as follows:
congestion_window = kInitialWindow
bytes_in_flight = 0
recovery_start_time = 0
ssthresh = infinite
ecn_ce_counter = 0
7.9.4. On Packet Sent
Whenever a packet is sent, and it contains non-ACK frames, the packet
increases bytes_in_flight.
OnPacketSentCC(bytes_sent):
bytes_in_flight += bytes_sent
7.9.5. On Packet Acknowledgement
Invoked from loss detection's OnPacketAcked and is supplied with the
acked_packet from sent_packets.
InRecovery(sent_time):
return sent_time <= recovery_start_time
OnPacketAckedCC(acked_packet):
// Remove from bytes_in_flight.
bytes_in_flight -= acked_packet.size
if (InRecovery(acked_packet.time_sent)):
// Do not increase congestion window in recovery period.
return
if (congestion_window < ssthresh):
// Slow start.
congestion_window += acked_packet.size
else:
// Congestion avoidance.
congestion_window += kMaxDatagramSize * acked_packet.size
/ congestion_window
7.9.6. On New Congestion Event
Invoked from ProcessECN and OnPacketsLost when a new congestion event
is detected. May start a new recovery period and reduces the
congestion window.
Iyengar & Swett Expires June 21, 2019 [Page 26]
Internet-Draft QUIC Loss Detection December 2018
CongestionEvent(sent_time):
// Start a new congestion event if the sent time is larger
// than the start time of the previous recovery epoch.
if (!InRecovery(sent_time)):
recovery_start_time = Now()
congestion_window *= kLossReductionFactor
congestion_window = max(congestion_window, kMinimumWindow)
ssthresh = congestion_window
// Collapse congestion window if persistent congestion
if (pto_count > kPersistentCongestionThreshold):
congestion_window = kMinimumWindow
7.9.7. Process ECN Information
Invoked when an ACK frame with an ECN section is received from the
peer.
ProcessECN(ack):
// If the ECN-CE counter reported by the peer has increased,
// this could be a new congestion event.
if (ack.ce_counter > ecn_ce_counter):
ecn_ce_counter = ack.ce_counter
// Start a new congestion event if the last acknowledged
// packet was sent after the start of the previous
// recovery epoch.
CongestionEvent(sent_packets[ack.largest_acked].time_sent)
7.9.8. On Packets Lost
Invoked by loss detection from DetectLostPackets when new packets are
detected lost.
OnPacketsLost(lost_packets):
// Remove lost packets from bytes_in_flight.
for (lost_packet : lost_packets):
bytes_in_flight -= lost_packet.size
largest_lost_packet = lost_packets.last()
// Start a new congestion epoch if the last lost packet
// is past the end of the previous recovery epoch.
CongestionEvent(largest_lost_packet.time_sent)
8. Security Considerations
Iyengar & Swett Expires June 21, 2019 [Page 27]
Internet-Draft QUIC Loss Detection December 2018
8.1. Congestion Signals
Congestion control fundamentally involves the consumption of signals
- both loss and ECN codepoints - from unauthenticated entities. On-
path attackers can spoof or alter these signals. An attacker can
cause endpoints to reduce their sending rate by dropping packets, or
alter send rate by changing ECN codepoints.
8.2. Traffic Analysis
Packets that carry only ACK frames can be heuristically identified by
observing packet size. Acknowledgement patterns may expose
information about link characteristics or application behavior.
Endpoints can use PADDING frames or bundle acknowledgments with other
frames to reduce leaked information.
8.3. Misreporting ECN Markings
A receiver can misreport ECN markings to alter the congestion
response of a sender. Suppressing reports of ECN-CE markings could
cause a sender to increase their send rate. This increase could
result in congestion and loss.
A sender MAY attempt to detect suppression of reports by marking
occasional packets that they send with ECN-CE. If a packet marked
with ECN-CE is not reported as having been marked when the packet is
acknowledged, the sender SHOULD then disable ECN for that path.
Reporting additional ECN-CE markings will cause a sender to reduce
their sending rate, which is similar in effect to advertising reduced
connection flow control limits and so no advantage is gained by doing
so.
Endpoints choose the congestion controller that they use. Though
congestion controllers generally treat reports of ECN-CE markings as
equivalent to loss [RFC8311], the exact response for each controller
could be different. Failure to correctly respond to information
about ECN markings is therefore difficult to detect.
9. IANA Considerations
This document has no IANA actions. Yet.
10. References
Iyengar & Swett Expires June 21, 2019 [Page 28]
Internet-Draft QUIC Loss Detection December 2018
10.1. Normative References
[QUIC-TRANSPORT]
Iyengar, J., Ed. and M. Thomson, Ed., "QUIC: A UDP-Based
Multiplexed and Secure Transport", draft-ietf-quic-
transport-17 (work in progress), December 2018.
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119,
DOI 10.17487/RFC2119, March 1997,
<https://www.rfc-editor.org/info/rfc2119>.
[RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
May 2017, <https://www.rfc-editor.org/info/rfc8174>.
[RFC8311] Black, D., "Relaxing Restrictions on Explicit Congestion
Notification (ECN) Experimentation", RFC 8311,
DOI 10.17487/RFC8311, January 2018,
<https://www.rfc-editor.org/info/rfc8311>.
10.2. Informative References
[FACK] Mathis, M. and J. Mahdavi, "Forward Acknowledgement:
Refining TCP Congestion Control", ACM SIGCOMM , August
1996.
[RACK] Cheng, Y., Cardwell, N., Dukkipati, N., and P. Jha, "RACK:
a time-based fast loss detection algorithm for TCP",
draft-ietf-tcpm-rack-04 (work in progress), July 2018.
[RFC3465] Allman, M., "TCP Congestion Control with Appropriate Byte
Counting (ABC)", RFC 3465, DOI 10.17487/RFC3465, February
2003, <https://www.rfc-editor.org/info/rfc3465>.
[RFC4653] Bhandarkar, S., Reddy, A., Allman, M., and E. Blanton,
"Improving the Robustness of TCP to Non-Congestion
Events", RFC 4653, DOI 10.17487/RFC4653, August 2006,
<https://www.rfc-editor.org/info/rfc4653>.
[RFC5681] Allman, M., Paxson, V., and E. Blanton, "TCP Congestion
Control", RFC 5681, DOI 10.17487/RFC5681, September 2009,
<https://www.rfc-editor.org/info/rfc5681>.
Iyengar & Swett Expires June 21, 2019 [Page 29]
Internet-Draft QUIC Loss Detection December 2018
[RFC5682] Sarolahti, P., Kojo, M., Yamamoto, K., and M. Hata,
"Forward RTO-Recovery (F-RTO): An Algorithm for Detecting
Spurious Retransmission Timeouts with TCP", RFC 5682,
DOI 10.17487/RFC5682, September 2009,
<https://www.rfc-editor.org/info/rfc5682>.
[RFC5827] Allman, M., Avrachenkov, K., Ayesta, U., Blanton, J., and
P. Hurtig, "Early Retransmit for TCP and Stream Control
Transmission Protocol (SCTP)", RFC 5827,
DOI 10.17487/RFC5827, May 2010,
<https://www.rfc-editor.org/info/rfc5827>.
[RFC6298] Paxson, V., Allman, M., Chu, J., and M. Sargent,
"Computing TCP's Retransmission Timer", RFC 6298,
DOI 10.17487/RFC6298, June 2011,
<https://www.rfc-editor.org/info/rfc6298>.
[RFC6582] Henderson, T., Floyd, S., Gurtov, A., and Y. Nishida, "The
NewReno Modification to TCP's Fast Recovery Algorithm",
RFC 6582, DOI 10.17487/RFC6582, April 2012,
<https://www.rfc-editor.org/info/rfc6582>.
[RFC6675] Blanton, E., Allman, M., Wang, L., Jarvinen, I., Kojo, M.,
and Y. Nishida, "A Conservative Loss Recovery Algorithm
Based on Selective Acknowledgment (SACK) for TCP",
RFC 6675, DOI 10.17487/RFC6675, August 2012,
<https://www.rfc-editor.org/info/rfc6675>.
[RFC6928] Chu, J., Dukkipati, N., Cheng, Y., and M. Mathis,
"Increasing TCP's Initial Window", RFC 6928,
DOI 10.17487/RFC6928, April 2013,
<https://www.rfc-editor.org/info/rfc6928>.
[RFC7661] Fairhurst, G., Sathiaseelan, A., and R. Secchi, "Updating
TCP to Support Rate-Limited Traffic", RFC 7661,
DOI 10.17487/RFC7661, October 2015,
<https://www.rfc-editor.org/info/rfc7661>.
[RFC8312] Rhee, I., Xu, L., Ha, S., Zimmermann, A., Eggert, L., and
R. Scheffenegger, "CUBIC for Fast Long-Distance Networks",
RFC 8312, DOI 10.17487/RFC8312, February 2018,
<https://www.rfc-editor.org/info/rfc8312>.
[TLP] Dukkipati, N., Cardwell, N., Cheng, Y., and M. Mathis,
"Tail Loss Probe (TLP): An Algorithm for Fast Recovery of
Tail Losses", draft-dukkipati-tcpm-tcp-loss-probe-01 (work
in progress), February 2013.
Iyengar & Swett Expires June 21, 2019 [Page 30]
Internet-Draft QUIC Loss Detection December 2018
10.3. URIs
[1] https://mailarchive.ietf.org/arch/search/?email_list=quic
[2] https://github.com/quicwg
[3] https://github.com/quicwg/base-drafts/labels/-recovery
Appendix A. Change Log
*RFC Editor's Note:* Please remove this section prior to
publication of a final version of this document.
Issue and pull request numbers are listed with a leading octothorp.
A.1. Since draft-ietf-quic-recovery-16
o Unify TLP and RTO into a single PTO; eliminate min RTO, min TLP
and min crypto timeouts; eliminate timeout validation (#2114,
#2166, #2168, #1017)
o Redefine how congestion avoidance in terms of when the period
starts (#1928, #1930)
o Document what needs to be tracked for packets that are in flight
(#765, #1724, #1939)
o Integrate both time and packet thresholds into loss detection
(#1969, #1212, #934, #1974)
o Reduce congestion window after idle, unless pacing is used (#2007,
#2023)
o Disable RTT calculation for packets that don't elicit
acknowledgment (#2060, #2078)
o Limit ack_delay by max_ack_delay (#2060, #2099)
o Initial keys are discarded once Handshake are avaialble (#1951,
#2045)
o Reorder ECN and loss detection in pseudocode (#2142)
o Only cancel loss detection timer if ack-eliciting packets are in
flight (#2093, #2117)
Iyengar & Swett Expires June 21, 2019 [Page 31]
Internet-Draft QUIC Loss Detection December 2018
A.2. Since draft-ietf-quic-recovery-14
o Used max_ack_delay from transport params (#1796, #1782)
o Merge ACK and ACK_ECN (#1783)
A.3. Since draft-ietf-quic-recovery-13
o Corrected the lack of ssthresh reduction in CongestionEvent
pseudocode (#1598)
o Considerations for ECN spoofing (#1426, #1626)
o Clarifications for PADDING and congestion control (#837, #838,
#1517, #1531, #1540)
o Reduce early retransmission timer to RTT/8 (#945, #1581)
o Packets are declared lost after an RTO is verified (#935, #1582)
A.4. Since draft-ietf-quic-recovery-12
o Changes to manage separate packet number spaces and encryption
levels (#1190, #1242, #1413, #1450)
o Added ECN feedback mechanisms and handling; new ACK_ECN frame
(#804, #805, #1372)
A.5. Since draft-ietf-quic-recovery-11
No significant changes.
A.6. Since draft-ietf-quic-recovery-10
o Improved text on ack generation (#1139, #1159)
o Make references to TCP recovery mechanisms informational (#1195)
o Define time_of_last_sent_handshake_packet (#1171)
o Added signal from TLS the data it includes needs to be sent in a
Retry packet (#1061, #1199)
o Minimum RTT (min_rtt) is initialized with an infinite value
(#1169)
Iyengar & Swett Expires June 21, 2019 [Page 32]
Internet-Draft QUIC Loss Detection December 2018
A.7. Since draft-ietf-quic-recovery-09
No significant changes.
A.8. Since draft-ietf-quic-recovery-08
o Clarified pacing and RTO (#967, #977)
A.9. Since draft-ietf-quic-recovery-07
o Include Ack Delay in RTO(and TLP) computations (#981)
o Ack Delay in SRTT computation (#961)
o Default RTT and Slow Start (#590)
o Many editorial fixes.
A.10. Since draft-ietf-quic-recovery-06
No significant changes.
A.11. Since draft-ietf-quic-recovery-05
o Add more congestion control text (#776)
A.12. Since draft-ietf-quic-recovery-04
No significant changes.
A.13. Since draft-ietf-quic-recovery-03
No significant changes.
A.14. Since draft-ietf-quic-recovery-02
o Integrate F-RTO (#544, #409)
o Add congestion control (#545, #395)
o Require connection abort if a skipped packet was acknowledged
(#415)
o Simplify RTO calculations (#142, #417)
Iyengar & Swett Expires June 21, 2019 [Page 33]
Internet-Draft QUIC Loss Detection December 2018
A.15. Since draft-ietf-quic-recovery-01
o Overview added to loss detection
o Changes initial default RTT to 100ms
o Added time-based loss detection and fixes early retransmit
o Clarified loss recovery for handshake packets
o Fixed references and made TCP references informative
A.16. Since draft-ietf-quic-recovery-00
o Improved description of constants and ACK behavior
A.17. Since draft-iyengar-quic-loss-recovery-01
o Adopted as base for draft-ietf-quic-recovery
o Updated authors/editors list
o Added table of contents
Acknowledgments
Authors' Addresses
Jana Iyengar (editor)
Fastly
Email: jri.ietf@gmail.com
Ian Swett (editor)
Google
Email: ianswett@google.com
Iyengar & Swett Expires June 21, 2019 [Page 34]