Skip to main content

Printer Finishing MIB
draft-ietf-printmib-finishing-16

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 3806.
Authors Ira McDonald , Harry Lewis , Ron Bergman
Last updated 2015-10-14 (Latest revision 2003-02-21)
RFC stream Independent Submission
Intended RFC status Informational
Formats
Additional resources Mailing list discussion
Stream ISE state (None)
Consensus boilerplate Unknown
Document shepherd (None)
IESG IESG state Became RFC 3806 (Informational)
Action Holders
(None)
Telechat date (None)
Responsible AD Ned Freed
Send notices to (None)
draft-ietf-printmib-finishing-16
INTERNET-DRAFT                                               Ron Bergman
[Request for Comments: XXXX]                  Hitachi Printing Solutions
[Target Category: Informational]                             Harry Lewis
                                                         IBM Corporation
                                                            Ira McDonald
                                                          High North Inc
                                                        19 February 2003

                         Printer Finishing MIB

                 <draft-ietf-printmib-finishing-16.txt>

                         Expires 19 August 2003

Status of this Memo

This document is an Internet-Draft and is in full conformance with all
provisions of section 10 of RFC2026.

Internet-Drafts are working documents of the Internet Engineering Task
Force (IETF), its areas, and its working groups.  Note that other groups
may also distribute working documents as Internet-Drafts.

Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time.  It is inappropriate to use Internet-Drafts as reference material
or to cite them other than as "work in progress".

To learn the current status of any Internet-Draft, please check the
"1id-abstracts.txt" listing contained in the Internet-Drafts Shadow
Directories on ftp.is.co.za (Africa), nic.nordu.net (Europe),
munnari.oz.au (Pacific Rim), ftp.ietf.org (US East Coast), or
ftp.isi.edu (US West Coast).

Copyright Notice

   Copyright (C) The Internet Society (2003).  All Rights Reserved.

Abstract

   This document defines a MIB module for the management of printer
   finishing device subunits.  The finishing device subunits applicable
   to this MIB are an integral part of the Printer System.  This MIB
   does not apply to a Finisher Device that is not connected to a
   Printer System.

Bergman, Lewis, McDonald                                       [Page 1]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

TABLE OF CONTENTS

1.  INTRODUCTION.......................................................2
1.1  Scope.............................................................3
1.2  Rational..........................................................3
1.3  The Internet-Standard Management Framework........................4
1.4  Read-Write Objects................................................4
2.  TERMINOLOGY........................................................5
2.1  General Terminology...............................................5
2.2  Process Specific Terminology......................................9
3.  FINISHER SUBUNITS INTEGRATED INTO THE PRINTER MODEL...............11
4.  FINISHING SPECIFICATIONS..........................................12
4.1  Multiple finDeviceTable Entries..................................12
4.2.1  FinPunchPatternTC..............................................13
4.2.2  FinPunchHoleTypeTC, punchHoleSizeMaxDim, punchHoleSizeMinDim...14
5.  THE ATTRIBUTE MECHANISM...........................................14
5.1  Conformance of Attribute Implementation..........................15
5.2  Useful, 'Unknown', and 'Other' Values for Objects and Attributes.15
5.3  Data Sub-types and Attribute Naming Conventions..................16
5.4  Single-Value (Row) Versus Multi-Value (MULTI-ROW) Attributes.....16
5.6  Index Value Attributes...........................................16
5.7  Attribute Specifications.........................................17
6.  ENUMERATIONS......................................................22
7.  IANA PRINTER FINISHING MIB SPECIFICATION..........................22
8.  PRINTER FINISHING MIB SPECIFICATION...............................28
9.  IANA CONSIDERATIONS...............................................45
10.  INTELLECTUAL PROPERTY............................................45
11.  INTERNATIONALIZATION CONSIDERATIONS..............................45
12.  NORMATIVE REFERENCES.............................................46
13.  INFORMATIVE REFERENCES...........................................46
14.  SECURITY CONSIDERATIONS..........................................47
15.  FULL COPYRIGHT STATEMENT.........................................48
16.  AUTHORS..........................................................48

1.  INTRODUCTION

   This document describes an SNMP Management Information Base (MIB) to
   provide for the management of in-line post-processing in a fashion
   that is currently provided for printers, using the Printer MIB
   [RFCnnnn]. The Printer Finishing MIB includes the following features:

Note to RFC Editor:  Insert RFC number 'nnnn' when assigned to the
Printer MIB.  See also the following paragraph.

    - Provides the status of the finishing device.
    - Queries and controls the features and configuration of the
      finishing device.
    - Enables and disables the finishing processes.
    - Allows unsolicited status from the finishing device.

   The Finisher MIB is defined as an extension of the Printer MIB

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 2]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   [RFCnnnn] and it is expected that the information defined in this
   document will be incorporated into a future update of the Printer
   MIB.

Note to RFC Editor:  Insert RFC number 'nnnn' when assigned to the
Printer MIB.

1.1  Scope

   This document provides a robust set of finishing devices, features,
   and functions, based upon today's state of the art of in-line
   finishing.  Since finishing typically accompanies higher speed
   network printers and copiers, in contrast to simple desktop devices,
   no attempt is made to limit the scope to "bare minimum".  On the
   other hand, the Printer Finishing MIB does not duplicate the
   production mail preparation, custom insertion, franking, and reprints
   that are covered by the DMTF Large Mailing Operations standard [LMO].

   Information supplied by the Printer Finishing MIB may be utilized by
   printer and finisher management applications engaged in monitoring
   status and managing configuration, and also used by print and
   finishing submission applications which are engaged in:

    - print-job-level finishing processes that are applied to a
      complete print job,

    - document-level finishing processes that are applied individually
      to each document in the print job,

    - document-level finishing processes that are applied to a selected
      document in the print job.

   Note that not all combinations of finishing processes are
   permitted.  Compatible combinations of finishing processes are
   implementation specific.  The MIB allows invalid combinations to be
   identified.

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

1.2  Rational

   The Printer MIB [RFCnnnn] is now successfully deployed in a large
   segment of the network printer market.  SNMP and/or HTTP enabled
   printers and software management applications are growing in numbers.

Note to RFC Editor:  Insert RFC number 'nnnn' when assigned to the
Printer MIB.

   There is an increase in the availability of network printers and
   copiers that include in-line finishing processes.  Thus a well

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 3]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   defined and ordered set of finishing objects is now necessary for
   printer management.

   The printer model defined in the Printer MIB includes finishing
   processes and the MIB was designed to later incorporate finisher
   objects or to be referenced by a future Finisher MIB.

1.3  The Internet-Standard Management Framework

   For a detailed overview of the documents that describe the current
   Internet-Standard Management Framework, please refer to section 7 of
   RFC 3410 [RFC3410].

   Managed objects are accessed via a virtual information store, termed
   the Management Information Base or MIB.  MIB objects are generally
   accessed through the Simple Network Management Protocol (SNMP).
   Objects in the MIB are defined using the mechanisms defined in the
   Structure of Management Information (SMI).  This memo specifies a MIB
   module that is compliant to the SMIv2, which is described in STD 58,
   RFC 2578 [RFC2578], STD 58, RFC 2579 [RFC2579] and STD 58, RFC 2580
   [RFC2580].

1.4  Read-Write Objects

   Some objects in the Finisher MIB reflect the existence or amount of a
   given resource within the finisher.  Some examples of such resources
   are the size and number of sheets in an inserter tray or the
   existence of certain finisher options.  Some finishers have automatic
   sensors for these resources.  Most finishers lack sensors for every
   property of every resource. The management application is allowed to
   write into objects that hold descriptive or existence values for
   finishers that cannot sense these values. The ability to change the
   value of a read-write object may depend on the implementation of the
   agent. Many  objects in the MIB are given read-write access, but an
   implementation might only permit a management application to change
   the value if the finisher can not sense the value itself. Note that
   even though some objects explicitly state the behavior of conditional
   ability to change values, any read-write object may act this way.

   Generally, an object is given read-write access in the Finisher MIB
   specification if:

   1. The object involves installation of a resource that some finishers
   cannot themselves detect.  Therefore, external means are needed to
   inform the device of the installation.  (Here external means include
   using the operator console, or remote management application) and

   2. The finisher will behave differently if the installation of the
   resource is reported than if the installation were not reported; that
   is, the object is not to be used as a place to put information not
   used by the finisher, i.e., not a "sticky-note".  Another way of

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 4]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   saying this is that the finisher believes that information given it
   and acts as if the information were true.

   3. The finisher may get hints that it may not know about the
   existence or properties of certain resources.  For example, a paper
   tray may be removed and re-inserted.  When this removal and insertion
   happens, the finisher may either assume that a property, such as the
   size of paper in the tray, has not changed or the finisher may change
   the value of the associated object to "unknown", as might be done for
   the amount of paper in the tray.  As long as the finisher acts
   according to the value in  the object either strategy is acceptable.

   4. It is an implementation-specific matter as to whether or not MIB
   object values are persistent across power cycles or cold starts.

2.  TERMINOLOGY

   Where appropriate, the Printer Finishing MIB will conform to the
   terminology, syntax, and semantics from the DMTF Large Mailing
   Operations standard [LMO], the Internet Printing Protocol [RFC2911],
   and/or the ISO Document Printing Application [DPA].

2.1  General Terminology

   Finisher Input:  An input tray on the finisher and not otherwise
   associated with the printer.  An example of a finisher input is a
   tray that holds finishing "inserts".

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 5]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

                         ^ Y
                         |
                         |<---- Reference Edge
                         |
                         |  |<--- Finishing Process Axis
                         |  |
                     --->|  |<--- Finishing Process Offset
                         |  |
       Head              +=========================+ (X2,Y4)
       Locations         #  |                      #
                   +-----#----+                    #
          -----Y3--|-----#--O | <--+- Head         #
          ^        +-----#----+    |  Mechanisms   #
          |              #  |      |               #
          |              #  |      |               #
          |              #  |      |               #
          |              #  |      |               #
          |        +-----#----+    |               #
          | ---Y2--|-----#--O | <--+               #
          | ^      +-----#----+    |               #
          | |            #  |      |               #
          | |            #  |      |               #
          | |            #  |      |               #
          | |            #  |      |               #
          | |      +-----#----+    |               #
          | | -Y1--|-----#--O | <--+               #
          | | ^    +-----#----+       bottom right #
          | | |          #  |               corner #    X
         --------------- +==+======================+ ---->
                     (0,0)  (X1,0)

      Figure 1 - Finishing Process Axis Parallel to Y Axis

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 6]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

            ^ Y
            |        Head Locations
            |<---------------->|---X2
            |<---->|---X1      |
            |      |           |
            |    +-|-+       +-|-+
            |    | | |       | | |  (X3,Y2)
            +======|===========|======+
            #    | | |       | | |    # Finishing Process Axis
            #----| O |-------| O |----#----- Y1
            #    +---+       +---+    #   ^
            #      ^           ^      #   |
            #      |           |      #   |
            #      +-----------+      #   |
            #      |                  #   |
            #     Head                #   |
            #     Mechanisms          #   |
            #                         #   |
            #                         # Finishing Process Offset
            #                         #   |
            #                         #   |
            #                         #   |
            #                         #   |
            #                         #   |
            #                         #   |
            #            bottom right #   |
            #                  corner #   v   X
            +=========================+ ------>
          (0,0)              Reference Edge

      Figure 2 - Finishing Process Axis Parallel to X Axis

  Finisher Output:  The output of the finisher.  Because processing is
   in-line, the finisher outputs are a direct extension of the set of
   printer outputs.

  Media Orientation:  All Finishing Processes are defined relative to a
    portrait orientation of the medium, regardless of the orientation of
    the printed image or the direction of feed.  The 'X' and 'Y' axis,
    therefore, will always reference the medium as shown in figures 1
    and 2, with the 'X' axis always along the short edge of the medium.
    All edges and corners are also defined with the medium orientation
    as shown using the syntax top, bottom, left, and right.  Thus the
    bottom edge of the medium is at Y = 0, the left edge is at X = 0,
    and the bottom right corner is at (X2,0) as shown in the figure 1
    and at (X3,0) as shown in figure 2.

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 7]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

  Finishing:  Defined by DPA as an operation on a document following the
    completion of the image process.  Finishing processes defined within
    this document are those applied to one or more instances of
    rectangular paper sheet media.

   Finishing Process:  Defined by DPA as an operation applied by a
     machine such as trimming a document, folding the sheets in a
     document, and applying a binding to a document.

   Finishing Specification:  Defined by DPA as the specific sequence of
     operations for a serial combination of finishing processes.  The
     exact sequential order of the processes, in many cases, is
     critical to the obtaining the desired result.  For example, a
     folding operation followed by trimming could provide a very
     different result than if the trimming was followed by the folding.

   Finishing Process Parameters:  This parameter set is used to create a
     detailed definition of the finishing process.  Generic Finishing
     Process Parameters are applicable to any Finishing Specification.

   - Head Mechanism:  Defined by DPA as the physical mechanism that is
     used to perform a finishing process.  The head position may be
     fixed or variable depending upon the capabilities of the device.

   - Reference Edge:  Defined by DPA as the edge of the document
     relative to the axis to which the finishing process is applied.
     The edge of the medium defined to be the Reference Edge may be
     either the 'X' or the 'Y' axis, depending upon the finishing
     process to be performed.

     Note that the Reference Edge may change from one finishing process
     to another for one of two reasons.  First, a subsequent process may
     require a different Reference Edge.  Second, the actual dimensions
     of the document may change, for example as a result of a folding or
     a trimming operation.

   - Jog Edge:  Defined by DPA as one of the two edges that is
     perpendicular to the Reference Edge.  Specifying the Jog Edge
     parameter indicates the edges of all sheets which correspond to
     the Jog Edge are aligned.

   - Finishing Process Axis:  Defined by DPA as the axis which some
     finishing processes are applied to or referenced from by the Head
     Mechanism.  Examples are the axis for a fold process or the axis
     for a punch process.

   - Head Locations:  Defined by DPA as the position of the Heads on the
     Finishing Process Axis.

   - Finishing Process Offset:  The offset from the Reference Edge to
     the Finishing Process Axis at which the finishing process takes

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 8]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

     place or is applied.

2.2  Process Specific Terminology

  FOLDING:

  Z Fold:  A fold in which two folds are placed in the sheet in opposite
    directions.  The first fold is located at 25% of the sheet length,
    and the second is located at 50% of the sheet length (i.e., the
    center of the sheet).  Z Folding is often used on 11x17 inch or A3
    size sheets, when they are included in sets containing 8.5x11 inch
    or A4 size sheets.

  Half Fold:  To fold a sheet in half so that one of the resulting
    dimensions are exactly half the original sheet.  Often used for
    signatures or booklets.

  Letter Fold:  Folding a sheet roughly in thirds.  Usually performed on
    8.5x11 inch or A4 size sheets for insertion into an envelope.

  Signature:  The process by which images are placed on a large sheet of
    paper in correct panel areas and in the proper orientation such that
    when the sheet is folded it will produce a booklet with each page in
    the proper order and orientation.

  BINDING:

  Adhesive Binding:  A method of attaching sheets together to form a
    book or booklet using glue or adhesive.  Some adhesive binding
    methods apply the glue to sheets individually, before merging them
    together for form a book, but most methods involve the application
    of adhesive to an entire book of sheets.

  Comb Binding:  A method of binding in which a series of small
    rectangular holes is placed along the bind edge of the sheets.  The
    sheets are then held together using a tube shaped plastic binding
    strip with comb like fingers that fit through the holes in the
    sheets.

  Spiral Binding:  Sometimes referred to as wire binding, this binding
    method is a mechanical bind in which the individual leaves are held
    together by a wire or plastic spiral that is fed through small holes
    in the paper binding edge.

  Padding:  Applying a non-penetrating adhesive to the edge of a stack
    of sheets such that the sheets can be easily peeled off one at a
    time.  Frequently used for forms.

  Velo Binding:  A bind formed by punching holes into the edge of the
    sheets, placing a two piece plastic strip (one side formed with
    plastic pins that pass through the holes) along the edge and then

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 9]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

    staking the two pieces together.

  Perfect Binding:  A method of binding in which all pages are cut and
    roughed up at the back or binding edge and held together by an
    adhesive.

  Tape Binding:  The act of placing tape over the bind edge of a set.
    Sometimes contains adhesive to provide a functional bind to the set,
    and sometimes done for decorative purposes on a set that has been
    edge stapled.

  SLITTING/CUTTING/TRIMMING:

  Trim:  To cut the edges of a sheet or set of sheets.

  Face Trim:  To cut the edges of a set of sheets on a booklet of sheets
    that have been folded to eliminate the "creep" or edge shingling
    that results from the folding process.

  Gutter Trim:  To cut a larger sheet into smaller sheets eliminating
    the gutter between adjacent images.  This operation requires a
    minimum of two cuts for each gutter.

  Tab Cutting:  The act of cutting the edge of a sheet to form an index
    tab, thereby allowing quick identification and access.  The external
    tabs are sequentially placed along the book edge for visibility and
    ease of grasping.

  Perforating:  The act of cutting a series of very small, closely
    spaced holes or slots into a sheet to allow for ease of separation
    of a portion of the sheet.  Sometimes also used to ease
    bending/hinging of heavy weight papers.

  Scoring:  A means of applying small linear grooves or impressions
    along a sheet to allow easy folding.   Often used on heavy weight
    sheets and book covers.

  Slitting:  The action of cutting apart a large sheet to form smaller
    sheets.  Usually done using a sharp circular roll system.

  STITCHING/STAPLING:

  Staple:  The process of binding a set of sheets together using a 'U'
    shaped piece of metal wire that is punched through the set. The ends
    of the metal staple are then bent over, or 'clinched' to hold the
    staple in place.   Technically the term 'stapler' refers to devices
    that use pre-cut metal staples, but the term is also commonly used
    to refer to devices that use wire spools and then cut/form the
    staple. (see the definition of Stitch)

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 10]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

  Stitch:  The process of binding a set of sheets together using a 'U'
    shaped piece of metal wire that is punched through the set.  The
    wire used to form the staple is cut and formed into a 'U' shape in
    the stitcher head, and the staple 'leg' length is often varied
    depending on the number of sheets to be bound together.  The ends of
    the metal staple are bent over, or 'clinched' to hold the staple in
    place.

    Stitching can also refer to the process of sewing the edges of the
    signatures of a book together.

  Saddle Stitch:  The process of stapling a set along its center line as
    part of a booklet making process.   Usually 2 or 3 staples are used.

  Dual Stapling:  The process of placing 2 staples along the bind edge
    of a set.   The staples are typically located at 25% and 75% of the
    length of the bind edge.   Although dual stapling is often performed
    on the long edge of a set, legal documents are frequently dual
    stapled along the top, or short edge of the set.

  Triple Stapling:  Same as above, but using 3 staples along the bind
    edge, and usually applies to the long edge only.

WRAPPING:

  Shrink Wrap:  A wrap of thin plastic which when heated will shrink and
    wrap tightly around the stack thus preparing it for shipment.

BANDING:

  Band Wrap:  Bundling a finished stack to prepare for shipment.  Also
    known as Strap Wrap.

ROTATING:

  Sheet Rotator:  A device that rotates each sheet as received from the
    Media Path to the proper orientation for the finisher processing.

3.  FINISHER SUBUNITS INTEGRATED INTO THE PRINTER MODEL

   The Printer Finisher Device subunits receive media from one or more
   Printer Media Path subunits and deliver the media to one or more
   Printer Output subunits after the completion of the finishing
   processes.  The Printer Model, as described in the Printer MIB
   [RFCnnnn], is modified adding the finisher subunit(s) and finisher
   supplies between the media path and output subunits as follows:

Note to RFC Editor:  Insert RFC number 'nnnn' when assigned.

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 11]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

                   +----------+
                 +----------+ |
                 |  Marker  | |
                 | Supplies |-+
                 +----------+
                       \
  +-----+               \ +------+                +--------+    +------+
  |     |                \|      |                |        |    |      |
+-----+ |    +-----+    +------+ |   +------+   +--------+ |  +------+ |
|Input|-+  +------+|    |Marker|-+  +------+|   |Finisher|-+  |Output|-+
|     |===>|      |+<==>|      |<==>|      |+==>|        |===>|      |
+-----+    +-+  +-+     +------+    +-+  +-+    +--------+    +------+
   \         |  ||                    |  ||         \
    \        |  ||                    |  ||          \
     \       |  ||                    |  ||    +----------+
  +-------+  |  |+--------------------|  ||    | Finisher |-+
  |       |  |  +---------------------+  ||    | Supplies | |
+-------+ |  |         Media Path        |+    +----------+ |
| Media |-+  +---------------------------+       |          |
|(opt.) |                                        +----------+
+-------+

4.  FINISHING SPECIFICATIONS

   The Finisher MIB is able to provide most of the information that is
   required to generate a Finishing Specification.  This includes;

   1. Finishing operations that can be performed on media that are
      associated with a specific printer media path and output subunit.

   2. Combinations of operations that cannot be performed.

   3. The location of the operation on the medium, if applicable.

   4. The physical characteristics of the result of the operation.
      For example, the size and shape of a punched hole, or if a fold
      operation creates a letter fold or a "Z" fold.

   The Finisher MIB permits an agent to describe the order that
   operations can be performed.

4.1  Multiple finDeviceTable Entries

   Each finishing operation supported by the printer is represented by
   one or more entries in the finDeviceTable.  Each entry in this table
   defines a "logical" finishing device, since the function of several
   table entries may be performed by a single finisher mechanism.
   Multiple entries may also exist in the table as a result of the
   existence of multiple finisher mechanisms that perform the same type

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 12]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   of operation.

   One example of possible multiple entries for a single finisher
   device, is a hole punch operation that creates more than one hole.
   This could be performed using a single die punch that moves to each
   required position or a multi-die punch that simultaneously creates
   all holes.  In either case, each defined hole position may be defined
   as a separate table entry.

   In both cases, if the punch positions can be individually selected,
   a table entry for each position would be necessary.

   For the multi-die punch, each head mechanism may have a different
   hole pattern or size.  If these differences are to be properly
   disclosed, a table entry for each head mechanism would be required.

4.2  Implicit Parameters

   Finishing operations that are specified by an enum define a
   standard operation and in many cases an implicit set of physical
   characteristics is to be included when specifying the enum.  If
   explicit values for these characteristics are not provided in the
   attributes table, the values defined in this section are to be
   implied.

4.2.1  FinPunchPatternTC

   enum pattern       |Reference| Reference | Hole spacing
                      | Edge    |Axis Offset| (see note 1)
   -------------------+---------+-----------+---------------------------
   twoHoleUSTop(4)    | topEdge |   note 2  | 2.75 inches
   threeHoleUS(5)     |  note 3 |   note 2  | 4.25 inches
   twoHoleDIN(6)      |  note 4 |   note 5  | 80 mm
   fourHoleDIN(7)     |  note 4 |   note 5  | 80 mm
   twentyTwoHoleUS(8) |  note 3 |   note 2  | .5 inches
   nineteenHoleUS(9)  |  note 3 |   note 9  | .5625 inches
   twoHoleMetric(10)  |  note 6 |   note 5  | 80 mm
   swedish4Hole(11)   |  note 4 |   note 5  | 21, 70, 21 mm
   twoHoleUSSide(12)  |  note 3 |   note 2  | 2.75 inches
   fiveHoleUS(13)     |  note 3 |   note 2  | 2, 2.25, 2.25, 2 in
   sevenHoleUS(14)    |  note 3 |   note 2  | 1, 1, 2.25, 2.25, 1, 1 in
   mixed7H4S(15)      |  note 4 |   note 5  | note 7
   norweg6Hole(16)    |  note 4 |   note 5  | note 8
   metric26Hole(17)   |  note 6 |   note 5  | 9.5 mm
   metric30Hole(18)   |  note 4 |   note 5  | 9.5 mm

   Notes:
      1. All hole to hole patterns are centered along the process edge.
      2. Offset is 0.18 inches to 0.51 inches.
      3. Reference edge is leftEdge(5) for letter and topEdge(3)
         for ledger.

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 13]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

      4. Reference edge is leftEdge(5) for A4 and topEdge(3) for A3.
      5. Offset is 4.5 mm to 13 mm.
      6. Reference edge is leftEdge(5) for B5 and topEdge(3) for B4.
      7. 7 holes and 4 slots are punched in a H-S-H-H-S-H-S-H-H-S-H
         pattern with 15, 25, 23, 20, 37, 37, 20, 23, 25, 15 mm spacing.
      8. 4 holes and 2 slots are punched in a H-H-S-S-H-H pattern with
         a 64, 18.5, 75, 18.5, 64 mm spacing.
      9. Offset is .188 inches.

4.2.2  FinPunchHoleTypeTC, punchHoleSizeMaxDim, punchHoleSizeMinDim

   enum pattern       | Hole Description
   -------------------+----------------------------------------
   twoHoleUSTop(4)    | round(3), .2 - .32 inch diameter
   threeHoleUS(5)     | round(3), .2 - .32 inch diameter
   twoHoleDIN(6)      | round(3),  5 - 8 mm diameter
   fourHoleDIN(7)     | round(3),  5 - 8 mm diameter
   twentyTwoHoleUS(8) | round(3), .2 - .32 inch diameter
   nineteenHoleUS(9)  | rectang(6), .313 inches X .125 inches
   twoHoleMetric(10)  | round(3),  5 - 8 mm diameter
   swedish4Hole(11)   | round(3),  5 - 8 mm diameter
   twoHoleUSSide(12)  | round(3), .2 - .32 inch diameter
   fiveHoleUS(13)     | round(3), .2 - .32 inch diameter
   sevenHoleUS(14)    | round(3), .2 - .32 inch diameter
   mixed7H4S(15)      | round(3),  5 - 8 mm diameter
                      | rectang(6),  12 mm X 6 mm
   norweg6Hole(16)    | round(3),  5 - 8 mm diameter
                      | rectang(6),  10 mm  X 5.5 mm
   metric26Hole(17)   | round(3),  5 - 8 mm
   metric30Hole(18)   | round(3),  5 - 8 mm

   Note: Hole size ranges are typical and are provided as a reference
   only.  Exact tolerances should be site defined.

5.  THE ATTRIBUTE MECHANISM

   Attributes provide a function similar to information objects, except
   that attributes are identified by an enum, instead of an OID.  Thus
   new attributes may be registered without requiring a change to the
   MIB.  In addition, an implementation that does not have the
   functionality represented by the attribute can omit the attribute
   entirely, rather than having to return a distinguished value.  The
   agent is free to create an attribute in the Attribute Table as soon
   as the agent is aware of the value of the attribute.

   The agent materializes finishing subunit attributes in a four-indexed
   finDeviceAttributeTable:

     1. hrDeviceIndex - which device in the host

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 14]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

     2. finDeviceIndex - which finisher subunit in the printer device

     3. finDeviceAttributeTypeIndex - which attribute

     4. finDeviceAttributeInstanceIndex - which attribute instance for
        those attributes that can have multiple values per finishing
        subunit.

5.1  Conformance of Attribute Implementation

   An agent SHALL implement any attribute if (1) the device supports the
   functionality represented by the attribute and (2) the information is
   available to the agent.  The agent MAY create the attribute row in
   the finDeviceAttributeTable when the information is available or MAY
   create the row earlier with the designated 'unknown' value
   appropriate for that attribute.  See next section.

   If the device does not implement or does not provide access to the
   information about an attribute, the agent SHOULD NOT create the
   corresponding row in the finDeviceAttributeTable.

5.2  Useful, 'Unknown', and 'Other' Values for Objects and Attributes

   Some attributes have a 'useful' Integer32 value, some have a 'useful'
   OCTET STRING value, some MAY have either or both depending on
   implementation, and some MUST have both.  See the
   finDeviceAttributeTypeTC textual convention for the specification of
   each attribute.

   NOTE: In some instances, objects with a MAX-ACCESS of read-write will
   result in an SNMPv1 error or SNMPv2 exception during a write
   operation.  The administrative security policy may restrict a class
   of users to read-only or, more importantly, the implementation may
   implement a subset of read-write objects as read-only.  This should
   be expected to be the case for a device that can properly sense the
   value of an object and does not want the value to be externally
   modified.

   In general, values for objects and attributes have been chosen so
   that a management application will be able to determine whether a
   'useful', 'unknown', or 'other' value is available.  When a useful
   value is not available for an object that agent SHALL return a zero-
   length string for octet strings, the value 'unknown(2)' for enums, a
   '0' value for an object that represents an index in another table,
   and a value '-2' for counting integers.

   Since each attribute is represented by a row consisting of both the
   finDeviceAttributeValueAsInteger and finDeviceAttributeValueAsOctets
   MANDATORY objects, SNMP requires that the agent SHALL always create
   an attribute row with both objects specified.  However, for most

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 15]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   attributes the agent SHALL return a "useful" value for one of the
   objects and SHALL return the 'other' value for the other object.  For
   integer only attributes, the agent SHALL always return a zero-length
   string value for the finDeviceAttributeValueAsOctets object.  For
   octet string only attributes, the agent SHALL always return a '-1'
   value for the finDeviceAttributeValueAsInteger object.

5.3  Data Sub-types and Attribute Naming Conventions

   Many attributes are sub-typed to give a more specific data type than
   Integer32 or OCTET STRING.  The data sub-type of each attribute is
   indicated on the first line(s) of the description.  Some attributes
   have several different data sub-type representations.  When an
   attribute has both an Integer32 data sub-type and an OCTET STRING
   data sub-type, the attribute can be represented in a single row in
   the finDeviceAttributeTable.  In this case, the data sub-type name is
   not included as the last part of the name of the attribute.  When the
   data sub-types cannot be represented by a single row in the
   finDeviceAttributeTable, each such representation is considered a
   separate attribute and is assigned a separate name and enum value.
   For these attributes, the name of the data sub-type is the last part
   of the name of the attribute.

5.4  Single-Value (Row) Versus Multi-Value (MULTI-ROW) Attributes

   Most attributes shall have only one row per finishing subunit.
   However, a few attributes can have multiple values per finishing
   subunit, where each value is a separate row in the
   finDeviceAttributeTable.  Unless indicated with 'MULTI-ROW:' in the
   finDeviceAttributeTypeTC description, an agent SHALL ensure that each
   attribute occurs only once in the finDeviceAttributeTable for a
   finishing subunit.  Most of the 'MULTI-ROW' attributes do not allow
   duplicate values, i.e., the agent SHALL ensure that each value occurs
   only once for a finishing subunit.  Only if the specification of the
   'MULTI-ROW' attribute also says "There is no restriction on the same
   xxx occurring in multiple rows" can the agent allow duplicate values
   to occur for a single finishing subunit.

5.5  Linked MUTI-ROW Values

   Some MULTI-ROW attributes are intended to go together.  Thus a set
   of value instances represent a single instance.  For example, the
   puncher attributes indicate the location, maximum size, minimum size
   and shape of the various holes that the puncher can produce.  So the
   first set of values could represent one kind of hole, and the second
   set another kind of hole, etc.

5.6  Index Value Attributes

   A number of attributes are indexes in other tables.  Such attribute
   names end with the word 'Index'.  If the agent has not (yet) assigned

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 16]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   an index value for a particular index attribute for a finishing
   subunit, the agent shall either: (1) return the value 0 or (2) not
   add this attribute to the finDeviceAttributeTable until the index
   value is assigned.  In the interests of brevity, the semantics for 0
   is specified once here and is not repeated for each index attribute
   specification and a DEFVAL of 0 is indicated.

5.7  Attribute Specifications

   This section specifies the set of attributes that are enumerated
   in finAttributeTypeTC.  The data type tag definitions 'INTEGER:'
   or 'OCTETS', indicate if the attribute can be represented using
   the object finDeviceAttributeAsInteger or the object
   finDeviceAttributeAsOctets, respectively.  In some cases, a choice
   between the two data types is possible and for a few attributes both
   objects may be required at the same time to properly present the
   value.

   NOTE - The enum assignments are grouped logically with values
   assigned in groups of 10, so that additional values may be
   registered in the future and assigned a value that is part of
   their logical grouping.

   Values in the range 2**30 to 2**31-1 are reserved for private or
   experimental usage.  This range corresponds to the same range
   reserved in IPP.  Implementers are warned that use of such values
   may conflict with other implementations.  Implementers are encouraged
   to request registration of enum values following the procedures in
   Section 6.1.

   The attribute types defined at the time of completion of this
   specification are:

      finAttributeTypeIndex              Data type
      ---------------------              ---------
      other(1),                          Integer32
                                         AND/OR
                                         OCTET STRING (SIZE(0..63))
         INTEGER: and/or OCTETS:  An attribute that is not currently
           approved and registered.

   A. Generic finisher subunit attributes that apply to all finisher
      subunit types.  (3..)

      deviceName(3),                     OCTET STRING (SIZE(0..63))
         OCTETS:  The name assigned to this finisher device subunit.

      deviceVendorName(4),               OCTET STRING (SIZE(0..63))
         OCTETS:  The name of the vendor of this finisher device
           subunit.

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 17]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

      deviceModel(5),                    OCTET STRING (SIZE(0..63))
         OCTETS:  The model name of this finisher device subunit.

      deviceVersion(6),                  OCTET STRING (SIZE(0..63))
         OCTETS:  The version string for this finisher device
           subunit.

      deviceSerialNumber(7),             OCTET STRING (SIZE(0..63))
         OCTETS:  The serial number assigned to this finisher device
           subunit.

      maximumSheets(8),                  Integer32 (-2..32767)
         INTEGER:  Defines the maximum number of media sheets that a
           finisher device is able to process.

      finProcessOffsetUnits(9),          PrtMediaUnitTC
         INTEGER:  An enumeration which defines the units of measure
           for the attributes finAxisOffset, finHeadLocation,
           punchHoleSizeLongDim, and punchHoleSizeShortDim.

      finReferenceEdge(10),              FinEdgeTC
         INTEGER:  An enumeration which defines which edge of the
           form is the reference for this finishing process.  The
           Finishing Process Axis will be parallel to this axis.

      finAxisOffset(11),                 Integer32 (-2..2147483647)
         INTEGER:  Defines the offset of the Finishing Process
           Axis from the parallel Reference Edge.  For a value of
           finEdgeTC equal to TopEdge or RightEdge, the value
           given is to interpreted as a negative offset from the
           reference edge.  The units of measure are defined by the
           attribute finProcessOffsetUnits.

      finJogEdge(12),                    FinEdgeTC
         INTEGER:  An enumeration which defines a second edge of the
           document to which the media is aligned.  The jog edge must
           be perpendicular to the edge defined by finReferenceEdge.

      finHeadLocation(13),               Integer32 (-2..2147483647)
         INTEGER: MULTI-ROW:  Defines the position of the Head
           Mechanism relative to the axis, 'X' or 'Y', that is
           perpendicular to the Process Axis.  The units of measure
           are defined by the attribute finProcessOffsetUnits.

      finOperationRestrictions(14),      Integer32 (0..65535)
         INTEGER: MULTI-ROW:  Defines the finDeviceIndex of a
           finishing process which cannot be combined with the
           process defined by the finDeviceIndex for this
           finDeviceAttributeTable instance.  When this condition
           occurs this attribute SHALL be presented in the
           attribute tables for both finishing processes that cannot

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 18]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

           be combined.

      finNumberOfPositions(15),          Integer32 (0..65535)
         INTEGER:  Defines the total number of head positions for
           this finishing process.  Each position many be realized by
           a unique head mechanism or a single head mechanism may be
           automatically moved to each position.

      namedConfiguration(16),            OCTET STRING (SIZE(0..63))
         OCTETS:  Contains an administratively define name to define
           the finishing specification configured for this device.

      finMediaTypeRestriction(17),       OCTET STRING (SIZE(0..63))
         OCTETS: MULTI-ROW:  Defines the media type which cannot be
           combined with the process defined by the finDeviceIndex
           for this finDeviceAttributeTable instance.  Values are the
           same as defined for finSupplyMediaInputMediaName.

      finPrinterInputTraySupported(18),  Integer32 (0..65535)
         INTEGER: MULTI-ROW:  Defines the value of prtInputIndex
           corresponding to the printer input tray that can be used
           with the process defined by the finDeviceIndex for this
           finDeviceAttributeTable instance.  If this attribute is
           not present, this process can be used with any input tray
           in the printer.  For example, this attribute can indicate
           the current stapling capabilities for a stapler device
           for the input trays that depend upon the size and feed
           orientation.  So if there were two letter trays, one with
           A size and the other with B size, a two position stapler
           might specify in one row: upper-left and upper-right for
           the input tray with A size, but only upper-left for the
           one with B size.

      finPreviousFinishingOperation(19),         Integer32 (0..65535)
         INTEGER:  Defines the finDeviceIndex of the previous
           finishing process for implementations in which the
           finishing processes are performed in a prescribed order.
           Each finishing process in the fixed sequence is either
           performed or not performed according to the finishing
           instructions submitted with the job.  A value of 0
           indicates that this finishing process is the first in a
           sequence.  Finishing processes which are not part of a
           fixed sequence SHALL NOT have this attribute.

      finNextFinishingOperation(20),             Integer32 (0..65535)
         INTEGER:  Defines the finDeviceIndex of the next finishing
           process for implementations in which the finishing
           processes are performed in a prescribed order.  Each
           finishing process in the fixed sequence is either
           performed or not performed according to the finishing
           instructions submitted with the job.  A value of 0

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 19]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

           indicates that this finishing process is the last in a
           sequence.  Finishing processes which are not part of a
           fixed sequence SHALL NOT have this attribute.

   B. Stitcher type-specific attributes (30..)

      stitchingType(30),                 FinStitchingTypeTC
         INTEGER: MULTI-ROW:  Provides additional information
           regarding the stitching operation.

      stitchingDirection(31),            FinStitchingDirTypeTC
         INTEGER:  Defines the orientation of the stitching
           process.

      stitchingAngle(32),                FinStitchingAngleTypeTC
         INTEGER:  Defines enumerations that describe the angular
           orientation of the stitching process relative to the 'X'
           axis.

   C. Folder type-specific attributes (40..)

      foldingType(40),                   FinFoldingTypeTC
         INTEGER:  Provides additional information regarding the
           folding process.

   D. Binder type-specific attributes (50..)

      bindingType(50),                   FinBindingTypeTC
         INTEGER:  Provides additional information regarding the
           binding process.

   E. Trimmer type-specific attributes (60..)

   F. Die cutter type-specific attributes (70..)

   G. Puncher type-specific attributes (80..)

      punchHoleType(80),                 FinPunchHoleTypeTC
         INTEGER:  Provides information regarding the shape of the
           punched hole.

      punchHoleSizeLongDim(81),          Integer32 (-2..2147483647)
         INTEGER:  Defines the size of the punched hole in the
           longest dimension.  This dimension is typically measured
           parallel to either the long edge or the short edge of the
           media and the longest dimension will always be measured 90
           degrees from the shortest dimension.  For a symmetrical
           hole, such as a round or square hole, the shortest and
           longest dimensions will be identical. The units of measure
           are defined by the attribute finProcessOffsetUnits.

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 20]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

      punchHoleSizeShortDim(82),         Integer32 (-2..2147483647)
         INTEGER:  Defines the size of the punched hole in the
           shortest dimension.  This dimension is typically measured
           parallel to either the long edge or the short edge of the
           media and the shortest dimension will always be measured
           90 degrees from the longest dimension.  For a symmetrical
           hole, such as a round or square hole, the shortest and
           longest dimensions will be identical. The units of measure
           are defined by the attribute finProcessOffsetUnits.

      punchPattern(83),                  FinPunchPatternTC
         INTEGER:  Defines the hole pattern produced by the punch
           process.

   H. Perforator type-specific attributes (90..)

   I. Slitter type-specific attributes (100..)

      slittingType(100),                 FinSlittingTypeTC
         INTEGER:  Provides additional information regarding the
           slitting process.

   J. Separation cutter type-specific attributes (110..)

   K. Imprinter type-specific attributes (120..)

   L. Wrapper type-specific attributes (130..)

      wrappingType(130),                 FinWrappingTypeTC
         INTEGER:  Provides additional information regarding the
           wrapping process.

   M. Bander type-specific attributes (140..)

   N. Make Envelopes type-specific attributes (150..)

   O. Stacker type-specific attributes (160..)

      stackOutputType(160)               FinStackOutputTypeTC
         INTEGER:  Defines the job-to-job orientation produced by
           the stacker.

      stackOffset(161)                   Integer32 (-2..2147483647)
         INTEGER:  Defines the copy-to-copy output stack offset as
           a positive offset distance.  The units of measure are
           defined by finProcessOffsetUnits.

      stackRotation(162)                 Integer32 (-2..180)
         INTEGER:  Defines the copy-to-copy output stack rotation
           measured in degrees.  The value is the positive
           copy-to-copy rotation."

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 21]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

6.  ENUMERATIONS

   Enumerations (enums) are sets of symbolic values defined for use with
   one or more objects.  Commonly used enumeration sets are assigned a
   symbolic data type name (textual convention), rather than being
   specified in the SYNTAX clause of each individual object definition.

   Textual conventions defined in the Finisher MIB or the companion IANA
   Finisher MIB are extensible by RFC publication or Designated Expert
   Review (see 'IANA Considerations' section of this Finisher MIB and
   the DESCRIPTION clause in MODULE-IDENTITY of IANA Finisher MIB).  All
   of these textual conventions are:

     a) used more than once in the Finisher MIB itself; or

     b) imported and used in any other, including vendor private, MIB
        modules.

   The Finisher MIB has also defined the following special values for
   use with objects of the syntax "Integer32" to define conditions that
   are outside of the normal numeric range:  other(-1), unknown(-2), and
   partial(-3).  The 'partial' value means that there is some supply
   remaining (but the amount is indeterminate) or there is some capacity
   remaining (but the amount is indeterminate).  The Integer32 range
   field indicates in which objects these special values are valid.

6.1  Registering Additional Enumerated Values

   The Finisher MIB and the companion IANA Finisher MIB each defines one
   category of textual convention, according to the process employed
   to control the addition of new enumerations:

      Type 1 - All of the legal values are defined in the Finisher MIB.
      Additional enumerated values require the publication of a new
      Finisher MIB.

      Type 2 - All of the legal values are registered in the IANA
      Finisher MIB.  Additional enumerated values require a Designated
      Expert Review defined in "Guidelines for Writing an IANA
      Considerations Section in RFCs" [RFC2434].  The Designated Expert
      will be selected by the IETF Area Director(s) of the Applications
      Area.

7.  IANA PRINTER FINISHING MIB SPECIFICATION

IANA-FINISHER-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY,

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 22]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

        mib-2
            FROM SNMPv2-SMI
    TEXTUAL-CONVENTION
            FROM SNMPv2-TC;

ianafinisherMIB MODULE-IDENTITY
    LAST-UPDATED  "200302100000Z" -- February 10, 2003
    ORGANIZATION  "IANA"
    CONTACT-INFO  "Internet Assigned Numbers Authority

                  Postal: ICANN
                          4676 Admiralty Way, Suite 330
                          Marina del Rey, CA 90292

                  Tel:    +1 310 823 9358
                  E-Mail: iana@iana.org"

    DESCRIPTION   "This MIB module defines a set of finishing-related
                  textual conventions for use in Finisher MIB (RFC xxxx)
                  and other MIBs which need to specify finishing
                  mechanism details.

                  Any additions or changes to the contents of this MIB
                  module require either publication of an RFC, or
                  Designated Expert Review as defined in RFC 2434,
                  Guidelines for Writing an IANA Considerations Section
                  in RFCs.  The Designated Expert will be selected by
                  the IESG Area Director(s) of the Applications Area.

                  Copyright (C) The Internet Society (2003). This
                  version of this MIB module is part of RFC xxxx;
                  see the RFC itself for full legal notices."
    -- RFC Editor assigns above RFC xxxx.

    REVISION      "200302100000Z"  -- February 10, 2003
    DESCRIPTION   "Original version, published in coordination
                  with Finisher MIB (RFC xxxx)."
    -- RFC Editor assigns above RFC xxxx.

    ::= { mib-2 nnn } -- nnn to be assigned by IANA

-- Textual conventions for this MIB module

FinDeviceTypeTC ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
      "The defined finishing device subunit process
       enumerations."
    SYNTAX       INTEGER {
         other(1),
         unknown(2),

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 23]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

         stitcher(3),
         folder(4),
         binder(5),
         trimmer(6),
         dieCutter(7),
         puncher(8),
         perforater(9),
         slitter(10),
         separationCutter(11),
         imprinter(12),
         wrapper(13),
         bander(14),
         makeEnvelope(15),
         stacker(16),
         sheetRotator(17),
         inserter(18)
        }

FinAttributeTypeTC  ::= TEXTUAL-CONVENTION
    STATUS     current
    DESCRIPTION
        "This textual convention defines the set of enums for use in
         the finDeviceAttributeTable.  See section 5.7 for the complete
         specification of each attribute."
    SYNTAX       INTEGER {
         other(1),
         deviceName(3),
         deviceVendorName(4),
         deviceModel(5),
         deviceVersion(6),
         deviceSerialNumber(7),
         maximumSheets(8),
         finProcessOffsetUnits(9),
         finReferenceEdge(10),
         finAxisOffset(11),
         finJogEdge(12),
         finHeadLocation(13),
         finOperationRestrictions(14),
         finNumberOfPositions(15),
         namedConfiguration(16),
         finMediaTypeRestriction(17),
         finPrinterInputTraySupported(18),
         finPreviousFinishingOperation(19),
         finNextFinishingOperation(20),
         stitchingType(30),
         stitchingDirection(31),
         foldingType(40),
         bindingType(50),
         punchHoleType(80),
         punchHoleSizeLongDim(81),
         punchHoleSizeShortDim(82),

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 24]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

         punchPattern(83),
         slittingType(100),
         wrappingType(130),
         stackOutputType(160),
         stackOffset(161),
         stackRotation(162)
        }

FinEdgeTC ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
      "Specifies an edge for a Finishing Process."
    SYNTAX       INTEGER {
         topEdge(3),
         bottomEdge(4),
         leftEdge(5),
         rightEdge(6)
        }

FinStitchingTypeTC ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
      "The defined stitching type enumerations.  For the edgeStitch and
       stapleDual enums, the finReferenceEdge attribute is recommended
       to define the edge to which the operation applies."
    SYNTAX       INTEGER {
         other(1),         -- More information in other attributes
         unknown(2),
         stapleTopLeft(4),
         stapleBottomLeft(5),
         stapleTopRight(6),
         stapleBottomRight(7),
         saddleStitch(8),
         edgeStitch(9),
         stapleDual(10)
        }

FinStitchingDirTypeTC ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
      "Defines the direction, relative to the top sheet in the output
       subunit, that the stitching operation was performed.  For a
       topDown(3) process, the staple will be clinched on the bottom
       of the stack.  This parameter can be used to determine what
       order the pages of a booklet are to be printed such that the
       staple clinch will be on the inside of the resulting booklet."
    SYNTAX       INTEGER {
         unknown(2),
         topDown(3),
         bottomUp(4)
        }

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 25]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

FinStitchingAngleTypeTC ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
      "This enumeration provides a description of the angular
       orientation of each stitch in a single or multiple stitching
       operation, relative to the 'X' axis.  As with all finishing
       operations, the 'X' axis is always relative to the portrait
       orientation of the document regardless of the orientation
       of the printed image.  This enum is primarily applicable to
       corner stitching operations."
    SYNTAX       INTEGER {
         unknown(2),
         horizontal(3),
         vertical(4),
         slanted(5)
        }

FinFoldingTypeTC ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
     "The defined folding device process enumerations."
   SYNTAX       INTEGER {
         other(1),        -- More information in other attributes
         unknown(2),
         zFold(3),
         halfFold(4),
         letterFold(5)
        }

FinBindingTypeTC ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
      "The defined binding type enumerations."
    SYNTAX       INTEGER {
         other(1),          -- More information in other attributes
         unknown(2),
         tape(4),
         plastic(5),
         velo(6),
         perfect(7),
         spiral(8),
         adhesive(9),
         comb(10),
         padding(11)
        }

FinPunchHoleTypeTC ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
     "The defined hole type punch process enumerations."

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 26]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   SYNTAX       INTEGER {
         other(1),        -- More information in other attributes
         unknown(2),
         round(3),
         oblong(4),
         square(5),
         rectangular(6),
         star(7)
        }

FinPunchPatternTC ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
     "The defined hole pattern punch process enumerations."
   SYNTAX       INTEGER {
         other(1),           --Pattern to be defined in other attributes
         unknown(2),
         twoHoleUSTop(4),    --Letter/legal, 8.5 inch edge
         threeHoleUS(5),     --Letter/ledger, 11 inch edge
         twoHoleDIN(6),      --A4/A3, 297 mm edge
         fourHoleDIN(7),     --A4/A3, 297 mm edge
         twentyTwoHoleUS(8), --Letter/ledger, 11 inch edge
         nineteenHoleUS(9),  --Letter/ledger, 11 inch edge
         twoHoleMetric(10),  --B5/B4, 257 mm edge
         swedish4Hole(11),   --A4/A3, 297 mm edge
         twoHoleUSSide(12),  --Letter/ledger, 11 inch edge
         fiveHoleUS(13),     --Letter/ledger, 11 inch edge
         sevenHoleUS(14),    --Letter/ledger, 11 inch edge
         mixed7H4S(15),      --A4/A3, 297 mm edge
         norweg6Hole(16),    --A4/A3, 297 mm edge
         metric26Hole(17),   --B5/B4, 257 mm edge
         metric30Hole(18)    --A4/A3, 297 mm edge
        }

FinSlittingTypeTC ::= TEXTUAL-CONVENTION
    STATUS       current
    DESCRIPTION
      "The defined slitting type enumerations."
    SYNTAX       INTEGER {
         other(1),         -- More information in other attributes
         unknown(2),
         slitAndSeparate(4),
         slitAndMerge(5)
        }

FinWrappingTypeTC ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
     "The defined wrapping device process enumerations."
   SYNTAX       INTEGER {
         other(1),        -- More information in other attributes

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 27]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

         unknown(2),
         shrinkWrap(4),
         paperWrap(5)
        }

FinStackOutputTypeTC ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
     "The defined stack output type enumerations."
   SYNTAX       INTEGER {
         other(1),        -- More information in other attributes
         unknown(2),
         straight(4),     -- No offset, one on top of another
         offset(5),
         crissCross(6)    -- Rotated
        }
END

8.  PRINTER FINISHING MIB SPECIFICATION

Finisher-MIB DEFINITIONS ::= BEGIN

IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE, Integer32, mib-2     FROM SNMPv2-SMI
    MODULE-COMPLIANCE, OBJECT-GROUP                   FROM SNMPv2-CONF
    hrDeviceIndex                              FROM HOST-RESOURCES-MIB
    PrtInputTypeTC, PrtMarkerSuppliesTypeTC      FROM IANA-PRINTER-MIB
    printmib, PrtSubUnitStatusTC, PrtLocalizedDescriptionStringTC,
        PrtMarkerSuppliesSupplyUnitTC, PrtMediaUnitTC,
        PrtCapacityUnitTC, PrtMarkerSuppliesClassTC,
        PresentOnOff, prtMIBConformance               FROM Printer-MIB
    FinDeviceTypeTC, FinAttributeTypeTC         FROM IANA-FINISHER-MIB;

finisherMIB MODULE-IDENTITY
    LAST-UPDATED "200302100000Z"
    ORGANIZATION "PWG IEEE/ISTO Printer Working Group"
    CONTACT-INFO

        "Harry Lewis
        IBM
        Phone (303) 924-5337
        Email: harryl@us.ibm.com

        Send comments to the printmib WG using the Finisher MIB
        Project (FIN) Mailing List:  fin@pwg.org

        For further information, access the PWG web page under 'Finisher
        MIB':      http://www.pwg.org/

        Implementers of this specification are encouraged to join the
        fin mailing list in order to participate in discussions on any

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 28]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

        clarifications needed and registration proposals being reviewed
        in order to achieve consensus."
    DESCRIPTION
        "The MIB module for management of printer finisher units.
         The Finisher MIB is an extension of the Printer MIB.
         Copyright (C) The Internet Society (2003). This version of
         this MIB module is part of RFC xxxx; see the RFC itself for
         full legal notices."
    -- RFC Editor assigns above RFC xxxx.
    REVISION "200302100000Z"
    DESCRIPTION
        "The original version of this MIB."
    ::= { mib-2  nnn } -- nnn to be assigned by IANA

 -- Finisher Device Group (Mandatory)
--
-- A printer may support zero or more finishing subunits.  A
-- finishing device subunit may be associated with one or more
-- output subunits and one or more media path subunits.

finDevice  OBJECT IDENTIFIER  ::=  { printmib 30 }

finDeviceTable OBJECT-TYPE
    SYNTAX     SEQUENCE OF FinDeviceEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
      "This table defines the finishing device subunits,
       including information regarding possible configuration
       options and the status for each finisher device subunit."
    ::= { finDevice 1 }

finDeviceEntry OBJECT-TYPE
    SYNTAX      FinDeviceEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "There is an entry in the finishing device table for each
       possible finisher process.  Each individual finisher process is
       implemented by a finishing device represented in this table."
    INDEX  { hrDeviceIndex, finDeviceIndex }
    ::= { finDeviceTable 1 }

FinDeviceEntry ::= SEQUENCE {
      finDeviceIndex                 Integer32,
      finDeviceType                  FinDeviceTypeTC,
      finDevicePresentOnOff          PresentOnOff,
      finDeviceCapacityUnit          PrtCapacityUnitTC,
      finDeviceMaxCapacity           Integer32,
      finDeviceCurrentCapacity       Integer32,
      finDeviceAssociatedMediaPaths  OCTET STRING,

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 29]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

      finDeviceAssociatedOutputs     OCTET STRING,
      finDeviceStatus                PrtSubUnitStatusTC,
      finDeviceDescription           PrtLocalizedDescriptionStringTC
     }

finDeviceIndex OBJECT-TYPE
    SYNTAX      Integer32 (1..65535)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "A unique value used to identify a finisher process.
       Although these values may change due to a major
       reconfiguration of the printer system (e.g. the addition
       of new finishing processes), the values are normally
       expected to remain stable across successive power cycles."
    ::= { finDeviceEntry 1 }

finDeviceType OBJECT-TYPE
    SYNTAX      FinDeviceTypeTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "Defines the type of finishing process associated with this
       table row entry."
    ::= { finDeviceEntry 2 }

finDevicePresentOnOff OBJECT-TYPE
    SYNTAX      PresentOnOff
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "Indicates if this finishing device subunit is available
       and whether the device subunit is enabled."
    DEFVAL      { notPresent }
    ::= { finDeviceEntry 3 }

finDeviceCapacityUnit OBJECT-TYPE
    SYNTAX      PrtCapacityUnitTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The unit of measure for specifying the capacity of this
       finisher device subunit."
    ::= { finDeviceEntry 4 }

finDeviceMaxCapacity OBJECT-TYPE
    SYNTAX      Integer32 (-2..2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "The maximum capacity of this finisher device subunit in

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 30]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

       finDeviceCapacityUnits.  If the device can reliably sense
       this value, the value is sensed by the finisher device
       and is read-only: otherwise the value may be written by a
       management or control console application.  The value (-1)
       means other and specifically indicates that the device
       places no restrictions on this parameter.  The value (-2)
       means unknown."
    DEFVAL      { -2 }      -- unknown
    ::= { finDeviceEntry 5 }

finDeviceCurrentCapacity OBJECT-TYPE
    SYNTAX      Integer32 (-2..2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "The current capacity of this finisher device subunit in
       finDeviceCapacityUnits.  If the device can reliably sense
       this value, the value is sensed by the finisher and is
       read-only: otherwise the value may be written by a
       management or control console application.  The value (-1)
       means other and specifically indicates that the device
       places no restrictions on this parameter.  The value (-2)
       means unknown."
    DEFVAL      { -2 }      -- unknown
    ::= { finDeviceEntry 6 }

finDeviceAssociatedMediaPaths OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(1..63))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "Indicates the media paths which can supply media for this
       finisher device.  The value of this object is a bit map in an
       octet string with each position representing the value of a
       prtMediaPathIndex.  For a media path that can be a source
       for this finisher device subunit, the bit position equal
       to one less than the value of prtMediaPathIndex will be set.
       The bits are numbered starting with the most significant bit of
       the first byte being bit 0, the least significant bit of the
       first byte being bit 7, the most significant of the second byte
       being bit 8, and so on."
    ::= { finDeviceEntry 7 }

finDeviceAssociatedOutputs OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(1..63))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "Indicates the printer output subunits this finisher device
       subunit services.  The value of this object is a bit map in an
       octet string with each position representing the value of a

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 31]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

       prtOutputIndex.  For an output subunit that is serviced
       by this finisher device subunit, the bit position equal to
       to one less than the value of prtOutputIndex will be set.
       The bits are numbered starting with the most significant bit of
       the first byte being bit 0, the least significant bit of the
       first byte being bit 7, the most significant of the second byte
       being bit 8, and so on."
    ::= { finDeviceEntry 8 }

finDeviceStatus OBJECT-TYPE
    SYNTAX      PrtSubUnitStatusTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "Indicates the current status of this finisher device
       subunit."
    DEFVAL      { 5 }      -- unknown
    ::= { finDeviceEntry 9 }

finDeviceDescription OBJECT-TYPE
    SYNTAX      PrtLocalizedDescriptionStringTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "A free form text description of this device subunit in the
       localization specified by prtGeneralCurrentLocalization."
    ::= { finDeviceEntry 10 }

-- Finisher Supply Group (Mandatory)
--
-- A finisher device, but not all finisher devices, may have one or more
-- supplies associated with it.  For example a finisher may use both
-- binding tape and stitching wire supplies. A finisher may also have
-- more than one source for a given type of supply e.g. multiple supply
-- sources of ink for imprinters.

finSupply  OBJECT IDENTIFIER  ::=  { printmib 31 }

finSupplyTable OBJECT-TYPE
    SYNTAX     SEQUENCE OF FinSupplyEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
      "Each unique source of supply is an entry in the finisher
       supply table. Each supply entry has its own
       characteristics associated with it such as colorant and
       current supply level."
    ::= { finSupply 1 }

finSupplyEntry OBJECT-TYPE

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 32]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

    SYNTAX     FinSupplyEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
      "A list of finisher devices, with their associated
       supplies and supplies characteristics."
    INDEX  { hrDeviceIndex, finSupplyIndex }
    ::= { finSupplyTable 1 }

FinSupplyEntry ::= SEQUENCE {
      finSupplyIndex               Integer32,
      finSupplyDeviceIndex         Integer32,
      finSupplyClass               PrtMarkerSuppliesClassTC,
      finSupplyType                PrtMarkerSuppliesTypeTC,
      finSupplyDescription         PrtLocalizedDescriptionStringTC,
      finSupplyUnit                PrtMarkerSuppliesSupplyUnitTC,
      finSupplyMaxCapacity         Integer32,
      finSupplyCurrentLevel        Integer32,
      finSupplyColorName           OCTET STRING
     }

finSupplyIndex OBJECT-TYPE
    SYNTAX      Integer32 (1..65535)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "A unique value used by a finisher to identify this supply
       container/receptacle.  Although these values may change
       due to a major reconfiguration of the finisher (e.g. the
       addition of new supply sources to the finisher), values
       are normally expected to remain stable across successive
       power cycles."
    ::= { finSupplyEntry 1 }

finSupplyDeviceIndex OBJECT-TYPE
    SYNTAX      Integer32 (0..65535)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The value of finDeviceIndex corresponding to the finishing
       device subunit with which this finisher supply is associated.
       The value zero indicates the associated finishing device is
       Unknown."
    ::= { finSupplyEntry 2 }

finSupplyClass OBJECT-TYPE
    SYNTAX      PrtMarkerSuppliesClassTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This value indicates whether this supply entity

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 33]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

       represents a supply that is consumed or a container that
       is filled."
    ::= { finSupplyEntry 3 }

finSupplyType OBJECT-TYPE
    SYNTAX      PrtMarkerSuppliesTypeTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The type of this supply."
    ::= { finSupplyEntry 4 }

finSupplyDescription OBJECT-TYPE
    SYNTAX      PrtLocalizedDescriptionStringTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The description of this supply/receptacle in text useful
       for operators and management applications and in the
       localization specified by prtGeneralCurrentLocalization."
    ::= { finSupplyEntry 5 }

finSupplyUnit OBJECT-TYPE
    SYNTAX      PrtMarkerSuppliesSupplyUnitTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "Unit of measure of this finisher supply container or
       receptacle."
    ::= { finSupplyEntry 6 }

finSupplyMaxCapacity OBJECT-TYPE
    SYNTAX      Integer32 (-2..2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "The maximum capacity of this supply container/receptacle
       expressed in Supply Units.  If this supply container/
       receptacle can reliably sense this value, the value is
       sensed  and is read-only; otherwise the value may be
       written by a control panel or management application.  The
       value (-1) means other and places no restrictions on this
       parameter.  The value (-2) means unknown."
    DEFVAL      { -2 }      -- unknown
    ::= { finSupplyEntry 7 }

finSupplyCurrentLevel OBJECT-TYPE
    SYNTAX      Integer32 (-3..2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 34]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

      "The current level if this supply is a container; the
       remaining space if this supply is a receptacle. If this
       supply container/receptacle can reliably sense this value,
       the value is sensed and is read-only; otherwise the value
       may be written by a control panel or management
       application.  The value (-1) means other and places no
       restrictions on this parameter. The value (-2) means
       unknown.  A value of (-3) means that the printer knows there
       is some supply or remaining space."
    DEFVAL      { -2 }      -- unknown
    ::= { finSupplyEntry 8 }

--             Capacity Attribute Relationships
--
--                 MEDIA INPUT MEASUREMENT
--
--     _______ |                   |
--      |      |                   |
--      |      |                   |                   |
--      |      |_ _ _ _ _ _ _ _ _ _| ________________  |direction
--      |      |                   |      |            v
-- MaxCapacity |                   |      |
--      |      | Sheets remaining  | CurrentLevel
--      |      |                   |      |
--      v      |                   |      v
--     _______ +___________________+ _______

finSupplyColorName OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(0..63))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The name of the color associated with this supply."

    REFERENCE
       "The PWG Standardized Media Names specification [PWGMEDIA],
        section 4 Media Color Names, contains the recommended values
        for this object. Implementers may add additional string values.
        The naming conventions in ISO 9070 are recommended in order to
        avoid potential name clashes."
    ::= { finSupplyEntry 9 }

-- Finisher Supply, Media Input Group (Conditionally Mandatory)
--
-- A finisher device may have one or more associated supply media
-- inputs.  Each entry in this table defines an input for a
-- supply media type such as inserts, covers, etc.
--
-- This group is mandatory only if the printer system contains a

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 35]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

-- finisher device that requires a media supply used exclusively by a
-- finishing process.  Examples are inserts or covers that are not
-- supplied by an input subunit that provides media to the marker.

finSupplyMediaInput  OBJECT IDENTIFIER  ::=  { printmib 32 }

finSupplyMediaInputTable OBJECT-TYPE
    SYNTAX     SEQUENCE OF FinSupplyMediaInputEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
      "The input subunits associated with a finisher supply media
       are each represented by an entry in this table."
::= { finSupplyMediaInput 1 }

finSupplyMediaInputEntry OBJECT-TYPE
    SYNTAX     FinSupplyMediaInputEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
      "A list of finisher supply media input subunit features and
       characteristics."
    INDEX  { hrDeviceIndex, finSupplyMediaInputIndex }
    ::= { finSupplyMediaInputTable 1 }

FinSupplyMediaInputEntry ::= SEQUENCE {
      finSupplyMediaInputIndex            Integer32,
      finSupplyMediaInputDeviceIndex      Integer32,
      finSupplyMediaInputSupplyIndex      Integer32,
      finSupplyMediaInputType             PrtInputTypeTC,
      finSupplyMediaInputDimUnit          PrtMediaUnitTC,
      finSupplyMediaInputMediaDimFeedDir  Integer32,
      finSupplyMediaInputMediaDimXFeedDir Integer32,
      finSupplyMediaInputStatus           PrtSubUnitStatusTC,
      finSupplyMediaInputMediaName      OCTET STRING,
      finSupplyMediaInputName           OCTET STRING,
      finSupplyMediaInputDescription    PrtLocalizedDescriptionStringTC,
      finSupplyMediaInputSecurity       PresentOnOff,
      finSupplyMediaInputMediaWeight    Integer32,
      finSupplyMediaInputMediaThickness Integer32,
      finSupplyMediaInputMediaType      OCTET STRING
     }

finSupplyMediaInputIndex OBJECT-TYPE
    SYNTAX      Integer32 (1..65535)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "A unique value used by a finisher to identify this supply
       media input subunit.  Although these values may change
       due to a major reconfiguration of the finisher (e.g. the

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 36]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

       addition of new supply media input sources to the
       finisher), values are normally expected to remain stable
       across successive power cycles."
    ::= { finSupplyMediaInputEntry 1 }

finSupplyMediaInputDeviceIndex OBJECT-TYPE
    SYNTAX      Integer32 (0..65535)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The value of finDeviceIndex corresponding to the finishing
       device subunit with which this finisher media supply is
       associated.  The value zero indicates the associated device
       is unknown."
    ::= { finSupplyMediaInputEntry 2 }

finSupplyMediaInputSupplyIndex OBJECT-TYPE
    SYNTAX      Integer32 (0..65535)
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The value of finSupplyIndex corresponding to the finishing
       supply subunit with which this finisher media supply is
       associated.  The value zero indicates the associated finishing
       supply is unknown or there is no applicable finisher supply
       table entry."
    ::= { finSupplyMediaInputEntry 3 }

finSupplyMediaInputType OBJECT-TYPE
    SYNTAX      PrtInputTypeTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The type of technology (discriminated primarily according
       to the feeder mechanism type) employed by the input
       subunit."
    ::= { finSupplyMediaInputEntry 4 }

finSupplyMediaInputDimUnit OBJECT-TYPE
    SYNTAX      PrtMediaUnitTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "The unit of measure for specifying dimensional values for
       this input device."
    ::= { finSupplyMediaInputEntry 5 }

finSupplyMediaInputMediaDimFeedDir OBJECT-TYPE
    SYNTAX      Integer32 (-2..2147483647)
    MAX-ACCESS  read-write
    STATUS      current

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 37]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

    DESCRIPTION
      "This object provides the value of the dimension in the
       feed direction of the media that is placed or will be
       placed in this input device.  Feed dimension measurements
       are taken parallel to the feed direction of the device and
       measured in finSupplyMediaInputDimUnits.  If this input
       device can reliably sense this value, the value is sensed
       and is read-only access. Otherwise the value is read-write
       access and may be written by management or control panel
       applications. The value (-1) means other and specifically
       indicates that this device places no restrictions on this
       parameter. The value (-2) indicates unknown. "
    ::= { finSupplyMediaInputEntry 6 }

finSupplyMediaInputMediaDimXFeedDir OBJECT-TYPE
    SYNTAX      Integer32 (-2..2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "This object provides the value of the dimension across the
       feed direction of the media that is placed or will be
       placed in this input device.  The cross feed direction is
       ninety degrees relative to the feed direction on this
       device and measured in finSupplyMediaInputDimUnits.  If
       this input device can reliably sense this value, the value
       is sensed and is read-only access. Otherwise the value is
       read-write access and may be written by management or
       control panel applications. The value (-1) means other and
       specifically indicates that this device places no
       restrictions on this parameter. The value (-2) indicates
       unknown. "
    ::= { finSupplyMediaInputEntry 7 }

finSupplyMediaInputStatus OBJECT-TYPE
    SYNTAX      PrtSubUnitStatusTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "This value indicates the current status of this input
       device."
    DEFVAL      { 5 }      -- unknown
    ::= { finSupplyMediaInputEntry 8 }

finSupplyMediaInputMediaName OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(0..63))
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "The name of the current media contained in this input
       device. Examples are Engineering Manual Cover, Section A Tab
       Divider or any ISO standard names."

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 38]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

    ::= { finSupplyMediaInputEntry 9 }

finSupplyMediaInputName OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(0..63))
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "The name assigned to this input subunit."
    ::= { finSupplyMediaInputEntry 10 }

finSupplyMediaInputDescription OBJECT-TYPE
    SYNTAX      PrtLocalizedDescriptionStringTC
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
      "A free form text description of this input subunit in the
       localization specified by prtGeneralCurrentLocalization."
    ::= { finSupplyMediaInputEntry 11 }

finSupplyMediaInputSecurity OBJECT-TYPE
    SYNTAX      PresentOnOff
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "Indicates if this subunit has some security associated
       with it."
    ::= { finSupplyMediaInputEntry 12 }

finSupplyMediaInputMediaWeight OBJECT-TYPE
    SYNTAX      Integer32
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "The weight of the media associated with this Input device
       in grams per meter squared.  The value (-1) means other
       and specifically indicates that the device places no
       restriction on this parameter.  The value (-2) means
       unknown.  This object can be used to calculate the weight
       of individual pages processed by the document finisher.
       This value, when multiplied by the number of pages in a
       finished set, can be used to calculate the weight of a set
       before it is inserted into a mailing envelope."
    ::= { finSupplyMediaInputEntry 13 }

finSupplyMediaInputMediaThickness OBJECT-TYPE
    SYNTAX      Integer32 (-2..2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "This object identifies the thickness of the input media
       processed by this document input subunit measured in

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 39]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

       micrometers.  This value may be used by devices (or
       operators) to set up proper machine tolerances for the
       feeder operation.  The value (-2) indicates that the media
       thickness is unknown or not used in the setup for this
       input subunit."
    ::= { finSupplyMediaInputEntry 14 }

finSupplyMediaInputMediaType OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(0..63))
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "The name of the type of medium associated with this input
       subunit. "

    REFERENCE
       "The PWG Standardized Media Names specification [PWGMEDIA],
        section 3 Media Type Names, contains the recommended values
        for this object. Implementers may add additional string values.
        The naming conventions in ISO 9070 are recommended in order to
        avoid potential name clashes."
    ::= { finSupplyMediaInputEntry 15 }

-- Finisher Device Attribute Group (Mandatory)
--
-- A finisher device subunit may have one or more parameters that
-- cannot be specified by any other objects in the MIB.  The
-- Device Attribute group facilitates the definition of these
-- parameters.  The objects which define the attributes are
-- read-write, to allow both Set and Get operations.
--
-- At least one table entry must exist for each finisher device defined
-- by the MIB.  If no other entry is possible for a finisher device, the
-- deviceName(3) attribute MUST be returned.

finDeviceAttribute  OBJECT IDENTIFIER  ::=  { printmib 33 }

finDeviceAttributeTable OBJECT-TYPE
    SYNTAX     SEQUENCE OF FinDeviceAttributeEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
      "The attribute table defines special parameters that are
       applicable only to a minority of the finisher devices.
       An attribute table entry is used, rather than unique
       objects, to minimize the number of MIB objects and to
       allow for expansion without the addition of MIB objects.
       Each finisher device is represented by a separate row
       in the device subunit attribute table."
::= { finDeviceAttribute 1 }

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 40]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

finDeviceAttributeEntry OBJECT-TYPE
    SYNTAX     FinDeviceAttributeEntry
    MAX-ACCESS not-accessible
    STATUS     current
    DESCRIPTION
      "Each entry defines a finisher function parameter that
       cannot be represented by an object in the finisher
       device subunit table."
    INDEX  { hrDeviceIndex, finDeviceIndex,
             finDeviceAttributeTypeIndex,
             finDeviceAttributeInstanceIndex }
::= { finDeviceAttributeTable 1 }

FinDeviceAttributeEntry ::= SEQUENCE {
      finDeviceAttributeTypeIndex        FinAttributeTypeTC,
      finDeviceAttributeInstanceIndex    Integer32,
      finDeviceAttributeValueAsInteger   Integer32,
      finDeviceAttributeValueAsOctets    OCTET STRING
     }

finDeviceAttributeTypeIndex OBJECT-TYPE
    SYNTAX      FinAttributeTypeTC
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "Defines the attribute type represented by this row."
    ::= { finDeviceAttributeEntry 1 }

finDeviceAttributeInstanceIndex OBJECT-TYPE
    SYNTAX      Integer32 (1..65535)
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
      "An index that allows the discrimination of an attribute
       instance when the same attribute occurs multiple times for
       a specific instance of a finisher function.  The value of
       this index shall be 1 if only a single instance of the
       attribute occurs for the specific finisher function.
       Additional values shall be assigned in a contiguous manner."
    ::= { finDeviceAttributeEntry 2 }

finDeviceAttributeValueAsInteger OBJECT-TYPE
    SYNTAX      Integer32 (-2..2147483647)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "Defines the integer value of the attribute.  The value of
       the attribute is represented as an integer if the
       finAttributeTypeTC description for the attribute has the
       tag 'INTEGER:'.

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 41]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

       Depending upon the attribute enum definition, this object
       may be either an integer, a counter, an index, or an enum.
       Attributes for which the concept of an integer value is
       not meaningful SHALL return a value of -1 for this
       attribute."
    DEFVAL      { -2 }      -- unknown
    ::= { finDeviceAttributeEntry 3 }

finDeviceAttributeValueAsOctets OBJECT-TYPE
    SYNTAX      OCTET STRING (SIZE(0..63))
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
      "Contains the octet string value of the attribute.  The
       value of the attribute is represented as a string if the
       finAttributeTypeTC description for the attribute has the
       tag 'OCTETS:'.

       Depending upon the attribute enum definition, this object
       may be either a coded character set string (text) or a
       binary octet string.  Attributes for which the concept of
       an octet string value is not meaningful SHALL contain a
       zero length string."
    DEFVAL      { ''H }      -- empty string
    ::= { finDeviceAttributeEntry 4 }

-- Conformance Information

-- compliance statements

finMIBCompliance MODULE-COMPLIANCE
    STATUS  current
    DESCRIPTION
        "The compliance statement for agents that implement the
        finisher MIB."
    MODULE -- this module
    MANDATORY-GROUPS { finDeviceGroup, finSupplyGroup,
                       finDeviceAttributeGroup }

        OBJECT      finDevicePresentOnOff
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finDeviceMaxCapacity
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finDeviceCurrentCapacity

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 42]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMaxCapacity
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyCurrentLevel
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputMediaDimFeedDir
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputMediaDimXFeedDir
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputMediaName
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputName
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputSecurity
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputMediaWeight
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputMediaThickness
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finSupplyMediaInputMediaType
        MIN-ACCESS  read-only

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 43]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finDeviceAttributeValueAsInteger
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        OBJECT      finDeviceAttributeValueAsOctets
        MIN-ACCESS  read-only
        DESCRIPTION
            "It is conformant to implement this object as read-only."

        GROUP       finSupplyMediaInputGroup
        DESCRIPTION
            "This group is conditionally mandatory and must be included
             if a finisher device requires a media supply that is used
             exclusively by a finishing process."

    ::= { prtMIBConformance 5 }

finMIBGroups      OBJECT IDENTIFIER ::= { prtMIBConformance 6 }

finDeviceGroup OBJECT-GROUP
    OBJECTS { finDeviceType, finDevicePresentOnOff,
              finDeviceCapacityUnit, finDeviceMaxCapacity,
              finDeviceCurrentCapacity, finDeviceAssociatedMediaPaths,
              finDeviceAssociatedOutputs, finDeviceStatus,
              finDeviceDescription }
    STATUS  current
    DESCRIPTION
        "The finisher device group."
    ::= { finMIBGroups 1 }

finSupplyGroup OBJECT-GROUP
    OBJECTS { finSupplyDeviceIndex, finSupplyClass, finSupplyType,
              finSupplyDescription, finSupplyUnit, finSupplyMaxCapacity,
              finSupplyCurrentLevel, finSupplyColorName }
    STATUS  current
    DESCRIPTION
        "The finisher supply group."
    ::= { finMIBGroups 2 }

finSupplyMediaInputGroup OBJECT-GROUP
    OBJECTS { finSupplyMediaInputDeviceIndex,
              finSupplyMediaInputSupplyIndex, finSupplyMediaInputType,
              finSupplyMediaInputDimUnit,
              finSupplyMediaInputMediaDimFeedDir,
              finSupplyMediaInputMediaDimXFeedDir,
              finSupplyMediaInputStatus, finSupplyMediaInputMediaName,

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 44]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

              finSupplyMediaInputName, finSupplyMediaInputDescription,
              finSupplyMediaInputSecurity,
              finSupplyMediaInputMediaWeight,
              finSupplyMediaInputMediaThickness,
              finSupplyMediaInputMediaType }
    STATUS  current
    DESCRIPTION
        "The finisher supply, media input group."
    ::= { finMIBGroups 3 }

finDeviceAttributeGroup OBJECT-GROUP
    OBJECTS { finDeviceAttributeValueAsInteger,
              finDeviceAttributeValueAsOctets }
    STATUS  current
    DESCRIPTION
        "The finisher device attribute group.  This group is mandatory
         for a finisher device that contains an inserter subunit."
    ::= { finMIBGroups 4 }

END

9.  IANA CONSIDERATIONS

    The initial version the IANA Finisher MIB defined in section 7 of
    this document is to be archived by IANA and subsequently maintained
    according to the Process specified in section 6.1 of this document.

10.  INTELLECTUAL PROPERTY

   The IETF takes no position regarding the validity or scope of any
   intellectual property or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; neither does it represent that it
   has made any effort to identify any such rights.  Information on the
   IETF's procedures with respect to rights in standards-track and
   standards-related documentation can be found in RFC 2028.  Copies of
   claims of rights made available for publication and any assurances of
   licenses to be made available, or the result of an attempt made to
   obtain a general license or permission for the use of such
   proprietary rights by implementors or users of this specification can
   be obtained from the IETF Secretariat.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights which may cover technology that may be required to practice
   this standard.  Please address the information to the IETF Executive
   Director.

11.  INTERNATIONALIZATION CONSIDERATIONS

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 45]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   See the Printer MIB [RFCnnnn] section 2.2.1.1, 'International
   Considerations'.
Note to RFC Editor:  Insert RFC number 'nnnn' when assigned.

12.  NORMATIVE REFERENCES

   Find IETF (Internet Engineering Task Force) RFCs at www.ietf.org.
   Find PWG (IEEE/ISTO Printer Working Group) at www.pwg.org.

   [DPA] ISO/IEC 10175 Document Printing Application (DPA).  See
      ftp://ftp.pwg.org/pub/pwg/dpa/

   [LMO] Large Mailing Operations Specification, DMTF.  See
      http://www.dmtf.org/tech/apps.html

   [PWGMEDIA] IEEE-ISTO "The Printer Working Group Standard for Media
       Standardized Names", IEEE-ISTO 5101.1-2002.

   [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
      Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2434] Narten & Alvestrand, "Guidelines for Writing an IANA
       Considerations Section in RFCs", RFC 2434, October 1998.

   [RFC2578] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
      Rose, M., and S. Waldbusser, "Structure of Management
      Information Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.

   [RFC2579] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
      Rose, M., and S. Waldbusser, "Textual Conventions for SMIv2",
      STD 58, RFC 2579, April 1999.

   [RFC2580]   McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J.,
      Rose, M., and S. Waldbusser, "Conformance Statements for
      SMIv2", STD 58, RFC 2580, April 1999.

Note to RFC Editor:  Insert RFC number 'nnnn' when assigned.
   [RFCnnnn] Bergman, McDonald, Lewis, "The Printer MIB v2", RFC nnnn,
      2002.

13.  INFORMATIVE REFERENCES

   [RFC2911] Hastings et al, "Internet Printing Protocol/1.1: Model and
      Semantics", RFC 2911, September 2000.

   [RFC3410] Case, J., Mundy, R., Partain, D. and B. Stewart,
      "Introduction and Applicability Statements for Internet-
      Standard Management Framework", RFC 3410, December 2002.

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 46]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

14.  SECURITY CONSIDERATIONS

   There are a number of management objects defined in this MIB module
   with a MAX-ACCESS clause of read-write and/or read-create.  Such

   objects may be considered sensitive or vulnerable in some network
   environments.  The support for SET operations in a non-secure
   environment without proper protection can have a negative effect on
   network operations.  These are the tables and objects and their
   sensitivity/vulnerability:

   finDeviceTable:
      finDevicePresentOnOff -Possible severe inconvenience
      finDeviceMaxCapacity -Possible minor inconvenience
      finDeviceCurrentCapacity -Possible minor inconvenience
   finSupplyTable:
      finSupplyMaxCapacity -Possible minor inconvenience
      finSupplyCurrentLevel -Possible minor inconvenience
   finSupplyMediaInputTable
      finSupplyMediaInputMediaDimFeedDir -Possible severe inconvenience
      finSupplyMediaInputMediaDimXFeedDir -Possible severe inconvenience
      finSupplyMediaInputMediaName -Possible Minor inconvenience
      finSupplyMediaInputName -Possible Minor inconvenience
      finSupplyMediaInputSecurity -Possible Minor inconvenience
      finSupplyMediaInputMediaWeight -Possible Minor inconvenience
      finSupplyMediaInputMediaThickness -Possible Minor inconvenience
      finSupplyMediaInputMediaType -Possible Minor inconvenience
   finDeviceAttributeTable
      finDeviceAttributeValueAsInteger -Possible Minor inconvenience
      finDeviceAttributeValueAsOctets -Possible Minor inconvenience

   SNMP versions prior to SNMPv3 did not include adequate security.
   Even if the network itself is secure (for example by using IPSec),
   even then, there is no control as to who on the secure network is
   allowed to access and GET/SET (read/change/create/delete) the objects
   in this MIB module.

   It is RECOMMENDED that implementers consider the security features as
   provided by the SNMPv3 framework (see [RFC3410], section 8),
   including full support for the SNMPv3 cryptographic mechanisms (for
   authentication and privacy).

   Further, deployment of SNMP versions prior to SNMPv3 is NOT
   RECOMMENDED.  Instead, it is RECOMMENDED to deploy SNMPv3 and to
   enable cryptographic security.  It is then a customer/operator
   responsibility to ensure that the SNMP entity giving access to an
   instance of this MIB module is properly configured to give access to

   the objects only to those principals (users) that have legitimate
   rights to indeed GET or SET (change/create/delete) them.

   Where the operational capability of the printing device are
   especially vulnerable or difficult to administer, certain objects

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 47]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

   within this MIB have been tagged as READ-ONLY, preventing
   modification. Further, for all READ-WRITE objects within the MIB, the
   working group has included specific conformance guidelines stating
   that vendors are free to implement certain objects as READ-ONLY. This
   conformance allowance should cover cases where specific vendor
   vulnerabilities may differ from product to product. (See conformance
   section with regards to MIN-ACCESS clauses).

15.  FULL COPYRIGHT STATEMENT

   Copyright (C) The Internet Society (2003).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

16.  AUTHORS

   This document was created with significant contributions from the
   following individuals.

    Ron Bergman (Editor)
    Hitachi Printing Solutions America
    1757 Tapo Canyon Road
    Simi Valley, CA 93063-3394

    Phone: 805-578-4421
    Fax:  805-578-4001
    Email: Ron.Bergman@hitachi-ps.us

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 48]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

    Harry Lewis (chairman)
    IBM Corporation
    6300 Diagonal Hwy
    Boulder, CO 80301

    Phone: (303) 924-5337
    Fax:   (303) 924-4662
    Email: harryl@us.ibm.com

    Ira McDonald
    High North Inc.
    P.O. Box 221
    Grand Marais, MI  49839

    Phone: (906) 494-2434 or (906) 494-2697
    Email: imcdonald@sharplabs.com

    Send comments to the Printer Working Group (PWG) using the Finisher
    MIB Project (FIN) Mailing List:  fin@pwg.org

    Implementers of this specification are encouraged to join this email
    distribution list in order to participate in any discussions of
    clarification issues and review registration proposals for
    additional attributes and enum values.

    For further information, access the PWG web page under "FIN":
    http://www.pwg.org/

   The Printer MIB Working Group would like to extend a special thank
   you to the following individuals that put forth a significant effort
   to review this document and provide numerous suggestions for
   improvement.

    David Harrington . Enterasys Networks
    Juergen Schoenwaelder . TU Braunschweig
    Bert Wijnen . Lucent Technologies and IETF Op & Mngmt, Area Director

   Other Participants:

    Chuck Adams - Tektronix
    Carlos Becerra - HP
    Andy Davidson - Tektronix
    Mabry Dozier - QMS
    Lee Farrell - Canon
    Jennifer Gattis - Duplo USA
    Paul Gloger - Xerox
    Richard Hart - Digital

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 49]



INTERNET-DRAFT         Printer Finishing MIB            19 February 2003

    Tom Hastings - Xerox
    Scott Isaacson - Novell
    David Kellerman - Northlake Software
    Henrik Holst - i-data International
    Rick Landau - Digital
    Jay Martin - Underscore
    Gary Padlipski - Xerox
    Kevin Palmer - Duplo USA
    Bob Pentecost - HP
    Stuart Rowley - Kyocera
    Yuki Sacchi - Japan Computer Industry
    Philip Thambidunai - Okidata
    William Wagner - DPI/Osicom
    Chris Wellens - Interworking Labs
    Don Wright - Lexmark
    Lloyd Young - Lexmark

Bergman, Lewis, McDonald        Expires 19 August 2003         [Page 50]