Skip to main content

IS-IS Routing with Reverse Metric
draft-ietf-isis-reverse-metric-14

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8500.
Authors Naiming Shen , Shane Amante , Mikael Abrahamsson
Last updated 2018-10-16
Replaces draft-amante-isis-reverse-metric
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state Submitted to IESG for Publication
Document shepherd Christian Hopps
Shepherd write-up Show Last changed 2018-07-06
IESG IESG state Became RFC 8500 (Proposed Standard)
Consensus boilerplate Yes
Telechat date (None)
Responsible AD Alvaro Retana
Send notices to Christian Hopps <chopps@chopps.org>, aretana.ietf@gmail.com
IANA IANA review state Version Changed - Review Needed
draft-ietf-isis-reverse-metric-14
Networking Working Group                                         N. Shen
Internet-Draft                                             Cisco Systems
Intended status: Standards Track                               S. Amante
Expires: April 19, 2019                                      Apple, Inc.
                                                          M. Abrahamsson
                                                        T-Systems Nordic
                                                        October 16, 2018

                   IS-IS Routing with Reverse Metric
                   draft-ietf-isis-reverse-metric-14

Abstract

   This document describes a mechanism to allow IS-IS routing to quickly
   and accurately shift traffic away from either a point-to-point or
   multi-access LAN interface during network maintenance or other
   operational events.  This is accomplished by signaling adjacent IS-IS
   neighbors with a higher reverse metric, i.e., the metric towards the
   signaling IS-IS router.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on April 19, 2019.

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect

Shen, et al.             Expires April 19, 2019                 [Page 1]
Internet-Draft            IS-IS Reverse Metric              October 2018

   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Node and Link Isolation . . . . . . . . . . . . . . . . .   2
     1.2.  Distributed Forwarding Planes . . . . . . . . . . . . . .   3
     1.3.  Spine-Leaf Applications . . . . . . . . . . . . . . . . .   3
     1.4.  LDP IGP Synchronization . . . . . . . . . . . . . . . . .   3
     1.5.  IS-IS Reverse Metric  . . . . . . . . . . . . . . . . . .   3
     1.6.  Specification of Requirements . . . . . . . . . . . . . .   4
   2.  IS-IS Reverse Metric TLV  . . . . . . . . . . . . . . . . . .   4
   3.  Elements of Procedure . . . . . . . . . . . . . . . . . . . .   6
     3.1.  Processing Changes to Default Metric  . . . . . . . . . .   6
     3.2.  Multi-Topology IS-IS Support on Point-to-point links  . .   7
     3.3.  Multi-Access LAN Procedures . . . . . . . . . . . . . . .   7
     3.4.  LDP/IGP Synchronization on LANs . . . . . . . . . . . . .   8
     3.5.  Operational Guidelines  . . . . . . . . . . . . . . . . .   9
   4.  Security Considerations . . . . . . . . . . . . . . . . . . .   9
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  10
   6.  Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  10
   7.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  10
     7.1.  Normative References  . . . . . . . . . . . . . . . . . .  10
     7.2.  Informative References  . . . . . . . . . . . . . . . . .  11
   Appendix A.  Node Isolation Challenges  . . . . . . . . . . . . .  12
   Appendix B.  Link Isolation Challenges  . . . . . . . . . . . . .  13
   Appendix C.  Contributors' Addresses  . . . . . . . . . . . . . .  14
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  14

1.  Introduction

   The IS-IS [ISO10589] routing protocol has been widely used in
   Internet Service Provider IP/MPLS networks.  Operational experience
   with the protocol, combined with ever increasing requirements for
   lossless operations have demonstrated some operational issues.  This
   document describes the issues and a mechanism for mitigating them.

1.1.  Node and Link Isolation

   IS-IS routing mechanism has the overload-bit, which can be used by
   operators to perform disruptive maintenance on the router.  But in
   many operational maintenance cases, it is not necessary to divert all
   the traffic away from this node.  It is necessary to avoid only a
   single link during the maintenance.  More detailed descriptions of

Shen, et al.             Expires April 19, 2019                 [Page 2]
Internet-Draft            IS-IS Reverse Metric              October 2018

   the challenges can be found in Appendix A and Appendix B of this
   document.

1.2.  Distributed Forwarding Planes

   In a distributed forwarding platform, different forwarding line-cards
   may have interfaces and IS-IS connections to neighbor routers.  If
   one of the line-card's software resets, it may take some time for the
   forwarding entries to be fully populated on the line-card, in
   particular if the router is a PE (Provider Edge) router in ISP's MPLS
   VPN.  An IS-IS adjacency may be established with a neighbor router
   long before the entire BGP VPN prefixes are downloaded to the
   forwarding table.  It is important to signal to the adjacent IS-IS
   routers to raise metric values and not to use the corresponding IS-IS
   adjacency inbound to this router if possible.  Temporarily signaling
   the 'Reverse Metric' over this link to discourage the traffic via the
   corresponding line-card will help to reduce the traffic loss in the
   network.  In the meantime, the remote PE routers will select a
   different set of PE routers for the BGP best path calculation or use
   a different link towards the same PE router on which a line-card is
   resetting.

1.3.  Spine-Leaf Applications

   In the IS-IS Spine-Leaf extension [I-D.shen-isis-spine-leaf-ext], the
   leaf nodes will perform equal-cost or unequal-cost load sharing
   towards all the spine nodes.  In certain operational cases, for
   instance, when one of the backbone links on a spine node is
   congested, a spine node can push a higher metric towards the
   connected leaf nodes to reduce the transit traffic through the
   corresponding spine node or link.

1.4.  LDP IGP Synchronization

   In the [RFC5443], a mechanism is described to achieve LDP IGP
   synchronization by using the maximum link metric value on the
   interface.  But in the case of a new IS-IS node joining the broadcast
   network (LAN), it is not optimal to change all the nodes on the LAN
   to the maximum link metric value, as described in [RFC6138].  In this
   case, the Reverse Metric can be used to discourage both outbound and
   inbound traffic without affecting the traffic of other IS-IS nodes on
   the LAN.

1.5.  IS-IS Reverse Metric

   This document uses the routing protocol itself as the transport
   mechanism to allow one IS-IS router to advertise a "reverse metric"
   in an IS-IS Hello (IIH) PDU to an adjacent node on a point-to-point

Shen, et al.             Expires April 19, 2019                 [Page 3]
Internet-Draft            IS-IS Reverse Metric              October 2018

   or multi-access LAN link.  This would allow the provisioning to be
   performed only on a single node, setting a "reverse metric" on a link
   and have traffic bidirectionally shift away from that link gracefully
   to alternate, viable paths.

   This Reverse Metric mechanism is used for both point-to-point and
   multi-access LAN links.  Unlike the point-to-point links, the IS-IS
   protocol currently does not have a way to influence the traffic
   towards a particular node on LAN links.  This mechanism provides IS-
   IS routing the capability of altering traffic in both directions on
   either a point-to-point link or a multi-access link of an IS-IS node.

   The metric value in the "reverse metric" TLV and the Traffic
   Engineering metric in the sub-TLV being advertised is an offset or
   relative metric to be added to the existing local link and Traffic
   Engineering metric values of the receiver.

1.6.  Specification of Requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

2.  IS-IS Reverse Metric TLV

   The Reverse Metric TLV is a new TLV to be used inside IS-IS Hello
   PDU.  This TLV is used to support the IS-IS Reverse Metric mechanism
   that allows a "reverse metric" to be send to the IS-IS neighbor.

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |      Type     |     Length    |    Flags      |     Metric
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
             Metric  (Continue)        | sub-TLV Len   |Optional sub-TLV
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                       Figure 1: Reverse Metric TLV

   The Value part of the Reverse Metric TLV is composed of a 3 octet
   field containing an IS-IS Metric Value, a 1 octet field of Flags, and
   a 1 octet Reverse Metric sub-TLV length field representing the length
   of a variable number of sub-TLVs.  If the "sub-TLV len" is non-zero,
   then the Value field MUST also contain one or more sub-TLVs.

Shen, et al.             Expires April 19, 2019                 [Page 4]
Internet-Draft            IS-IS Reverse Metric              October 2018

   The Reverse Metric TLV MAY be present in any IS-IS Hello PDU.  A
   sender MUST only transmit a single Reverse Metric TLV in a IS-IS
   Hello PDU.  If a received IS-IS Hello PDU contains more than one
   Reverse Metric TLV, an implementation MUST ignore all the Reverse
   Metric TLVs.

      TYPE: 16
      LENGTH: variable (5 - 255 octets)
      VALUE:

         Flags (1 octet)
         Metric (3 octets)
         sub-TLV length (1 octet)
         sub-TLV data (0 - 250 octets)

          0 1 2 3 4 5 6 7
         +-+-+-+-+-+-+-+-+
         |  Reserved |U|W|
         +-+-+-+-+-+-+-+-+

                              Figure 2: Flags

   The Metric field contains a 24-bit unsigned integer.  This value is a
   metric offset that a neighbor SHOULD add to the existing, configured
   Default Metric for the IS-IS link [ISO10589].  Refer to "Elements of
   Procedure", in Section 3 for details on how an IS-IS router should
   process the Metric field in a Reverse Metric TLV.

   The Metric field, in the Reverse Metric TLV, is a "reverse offset
   metric" that will either be in the range of 0 - 63 when a "narrow"
   IS-IS metric is used (IS Neighbors TLV, Pseudonode LSP) [RFC1195] or
   in the range of 0 - (2^24 - 2) when a "wide" Traffic Engineering
   metric value is used, (Extended IS Reachability TLV) [RFC5305]
   [RFC5817].

   There are currently only two Flag bits defined.

   W bit (0x01): The "Whole LAN" bit is only used in the context of
   multi-access LANs.  When a Reverse Metric TLV is transmitted from a
   node to the Designated Intermediate System (DIS), if the "Whole LAN"
   bit is set (1), then a DIS SHOULD add the received Metric value in
   the Reverse Metric TLV to each node's existing Default Metric in the
   Pseudonode LSP.  If the "Whole LAN" bit is not set (0), then a DIS
   SHOULD add the received Metric value in the Reverse Metric TLV to the
   existing "default metric" in the Pseudonode LSP for the single node
   from whom the Reverse Metric TLV was received.  Please refer to
   "Multi-Access LAN Procedures", in Section 3.3, for additional
   details.  The W bit MUST be clear when a Reverse Metric TLV is

Shen, et al.             Expires April 19, 2019                 [Page 5]
Internet-Draft            IS-IS Reverse Metric              October 2018

   transmitted in an IIH PDU on a point-to-point link, and MUST be
   ignored when received on a point-to-point link.

   U bit (0x02): The "Unreachable" bit specifies that the metric
   calculated by addition of the reverse metric value to the "default
   metric" is limited to (2^24-1).  This "U" bit applies to both the
   default metric in the Extended IS Reachability TLV and the Traffic
   Engineering Default Metric sub-TLV of the link.  This is only
   relevant to the IS-IS "wide" metric mode.

   The Reserved bits of Flags field MUST be set to zero and MUST be
   ignored when received.

   The Reverse Metric TLV MAY include sub-TLVs when an IS-IS router
   wishes to signal additional information to its neighbor.  In this
   document, the Reverse Metric Traffic Engineering Metric sub-TLV, with
   Type 18, is defined.  This Traffic Engineering Metric contains a
   24-bit unsigned integer.  This sub-TLV is optional, if it appears
   more than once then the entire Reverse Metric TLV MUST be ignored.
   Upon receiving this Traffic Engineering METRIC sub-TLV in a Reverse
   Metric TLV, a node SHOULD add the received Traffic Engineering Metric
   offset value to its existing, configured Traffic Engineering Default
   Metric within its Extended IS Reachability TLV.  The use of other
   sub-TLVs is outside the scope of this document.  The "sub-TLV Len"
   value MUST be set to zero when an IS-IS router does not have Traffic
   Engineering sub-TLVs that it wishes to send to its IS-IS neighbor.

3.  Elements of Procedure

3.1.  Processing Changes to Default Metric

   It is important to use the same IS-IS metric type on both ends of the
   link and in the entire IS-IS area or level.  On the receiving side of
   the 'reverse-metric' TLV, the accumulated value of configured metric
   and the reverse-metric needs to be limited to 63 in "narrow" metric
   mode and to (2^24 - 2) in "wide" metric mode.  This applies to both
   the Default Metric of Extended IS Reachability TLV and the Traffic
   Engineering Default Metric sub-TLV in LSP or Pseudonode LSP for the
   "wide" metric mode case.  If the "U" bit is present in the flags, the
   accumulated metric value is to be limited to (2^24 - 1) for both the
   normal link metric and Traffic Engineering metric in IS-IS "wide"
   metric mode.

   If an IS-IS router is configured to originate a Traffic Engineering
   Default Metric sub-TLV for a link, but receives a Reverse Metric TLV
   from its neighbor that does not contain a Traffic Engineering Default
   Metric sub-TLV, then the IS-IS router MUST NOT change the value of
   its Traffic Engineering Default Metric sub-TLV for that link.

Shen, et al.             Expires April 19, 2019                 [Page 6]
Internet-Draft            IS-IS Reverse Metric              October 2018

3.2.  Multi-Topology IS-IS Support on Point-to-point links

   The Reverse Metric TLV is applicable to Multi-Topology IS-IS (M-ISIS)
   [RFC5120].  On point-to-point links, if an IS-IS router is configured
   for M-ISIS, it MUST send only a single Reverse Metric TLV in IIH PDUs
   toward its neighbor(s) on the designated link.  When an M-ISIS router
   receives a Reverse Metric TLV, it MUST add the received Metric value
   to its Default Metric in all Extended IS Reachability TLVs for all
   topologies.  If an M-ISIS router receives a Reverse Metric TLV with a
   Traffic Engineering Default Metric sub-TLV, then the M-ISIS router
   MUST add the received Traffic Engineering Default Metric value to
   each of its Default Metric sub-TLVs in all of its MT Intermediate
   Systems TLVs.  If an M-ISIS router is configured to advertise Traffic
   Engineering Default Metric sub-TLVs for one or more topologies, but
   does not receive a Traffic Engineering Default Metric sub-TLV in a
   Reverse Metric TLV, then the M-ISIS router MUST NOT change the value
   in each of the Traffic Engineering Default Metric sub-TLVs for all
   topologies.

3.3.  Multi-Access LAN Procedures

   On a Multi-Access LAN, only the DIS SHOULD act upon information
   contained in a received Reverse Metric TLV.  All non-DIS nodes MUST
   silently ignore a received Reverse Metric TLV.  The decision process
   of the routers on the LAN MUST follow the procedure in section
   7.2.8.2 of [ISO10589], and use the "Two-way connectivity check"
   during the topology and route calculation.

   The Reverse Metric Traffic Engineering sub-TLV also applies to the
   DIS.  If a DIS is configured to apply Traffic Engineering over a link
   and it receives metric sub-TLV in a Reverse Metric TLV, it should
   update the Traffic Engineering Default Metric sub-TLV value of the
   corresponding Extended IS Reachability TLV or insert a new one if not
   present.

   In the case of multi-access LANs, the "W" Flags bit is used to signal
   from a non-DIS to the DIS whether to change the metric and,
   optionally Traffic Engineering parameters for all nodes in the
   Pseudonode LSP or solely the node on the LAN originating the Reverse
   Metric TLV.

   A non-DIS node, e.g., Router B, attached to a multi-access LAN will
   send the DIS a Reverse Metric TLV with the W bit clear when Router B
   wishes the DIS to add the Metric value to the Default Metric
   contained in the Pseudonode LSP specific to just Router B.  Other
   non-DIS nodes, e.g., Routers C and D, may simultaneously send a
   Reverse Metric TLV with the W bit clear to request the DIS to add

Shen, et al.             Expires April 19, 2019                 [Page 7]
Internet-Draft            IS-IS Reverse Metric              October 2018

   their own Metric value to their Default Metric contained in the
   Pseudonode LSP.

   As long as at least one IS-IS node on the LAN sending the signal to
   DIS with the W bit set, the DIS would add the metric value in the
   Reverse Metric TLV to all neighbor adjacencies in the Pseudonode LSP,
   regardless if some of the nodes on the LAN advertise the Reverse
   Metric TLV without the W bit set.  The DIS MUST use the reverse
   metric of the highest source MAC address Non-DIS advertising the
   Reverse Metric TLV with the W bit set.

   Local provisioning on the DIS to adjust the Default Metric(s) is
   another way to insert Reverse Metric in the Pseudonode LSP towards an
   IS-IS node on a LAN.  In the case where Reverse Metric TLV is also
   used in the IS-IS Hello PDU of the node, the local provisioning MUST
   take precedence over received Reverse Metric TLVs.  For instance,
   local policy on the DIS may be provisioned to ignore the W bit
   signaling on a LAN.

   Multi-Topology IS-IS [RFC5120] specifies there is no change to
   construction of the Pseudonode LSP, regardless of the Multi-Topology
   capabilities of a multi-access LAN.  If any MT capable node on the
   LAN advertises the Reverse Metric TLV to the DIS, the DIS should
   update, as appropriate, the Default Metric contained in the
   Pseudonode LSP.  If the DIS updates the Default Metric in and floods
   a new Pseudonode LSP, those default metric values will be applied to
   all topologies during Multi-Topology SPF calculations.

3.4.  LDP/IGP Synchronization on LANs

   As described in [RFC6138] when a new IS-IS node joins a broadcast
   network, it is unnecessary and sometimes even harmful for all IS-IS
   nodes on the LAN to advertise maximum link metric.  [RFC6138]
   proposes a solution to have the new node not advertise its adjacency
   towards the pseudo-node when it is not in a "cut-edge" position.

   With the introduction of Reverse Metric in this document, a simpler
   alternative solution to the above mentioned problem can be used.  The
   Reverse Metric allows the new node on the LAN to advertise its
   inbound metric value to be the maximum and this puts the link of this
   new node in the last resort position without impacting the other IS-
   IS nodes on the same LAN.

   Specifically, when IS-IS adjacencies are being established by the new
   node on the LAN, besides setting the maximum link metric value (2^24
   - 2) on the interface of the LAN for LDP IGP synchronization as
   described in [RFC5443], it SHOULD advertise the maximum metric offset
   value in the Reverse Metric TLV in its IIH PDU sent on the LAN.  It

Shen, et al.             Expires April 19, 2019                 [Page 8]
Internet-Draft            IS-IS Reverse Metric              October 2018

   SHOULD continue this advertisement until it completes all the LDP
   label binding exchanges with all the neighbors over this LAN, either
   by receiving the LDP End-of-LIB [RFC5919] for all the sessions or by
   exceeding the provisioned timeout value for the node LDP/IGP
   synchronization.

3.5.  Operational Guidelines

   For the use case in Section 1.1, a router SHOULD limit the duration
   of advertising a Reverse Metric TLV towards a neighbor only for the
   period of operational window.

   The use of Reverse Metric does not alter IS-IS metric parameters
   stored in a router's persistent provisioning database.

   Routers that receive a Reverse Metric TLV MAY send a syslog message
   or SNMP trap, in order to assist in rapidly identifying the node in
   the network that is advertising an IS-IS metric or Traffic
   Engineering parameters different from that which is configured
   locally on the device.

   When the link Traffic Engineering metric is raised to (2^24 - 1)
   [RFC5817], either due to the reverse-metric mechanism or by explicit
   user configuration, this SHOULD immediately trigger the CSPF re-
   calculation to move the Traffic Engineering traffic away from that
   link.  It is RECOMMENDED also that the CSPF does the immediate CSPF
   re-calculation when the Traffic Engineering metric is raised to (2^24
   - 2) to be the last resort link.

   It is RECOMMENDED that implementations provide a capability to
   disable any changes by Reverse Metric mechanism through neighbor's
   Hello PDUs.  It can be to a node's individual interface Default
   Metric or Traffic Engineering parameters based upon receiving a
   properly formatted Reverse Metric TLVs.

   If an implementation enables this mechanism by default, it is
   RECOMMENDED that it be disabled by the operators when not explicitly
   using it.

4.  Security Considerations

   Security concerns for IS-IS are addressed in [ISO10589], [RFC5304],
   [RFC5310], and with various deployment and operational security
   considerations in [RFC7645].  The enhancement in this document makes
   it possible for one IS-IS router to manipulate the IS-IS Default
   Metric and, optionally, Traffic Engineering parameters of adjacent
   IS-IS neighbors.  Although IS-IS routers within a single Autonomous
   System nearly always are under the control of a single administrative

Shen, et al.             Expires April 19, 2019                 [Page 9]
Internet-Draft            IS-IS Reverse Metric              October 2018

   authority, it is highly RECOMMENDED that operators configure
   authentication of IS-IS PDUs to mitigate use of the Reverse Metric
   TLV as a potential attack vector.

5.  IANA Considerations

   IANA has allocated IS-IS TLV Codepoints of 16 for the Reverse Metric
   TLV.  This new TLV has the following attributes: IIH = y, LSP = n,
   SNP = n, Purge = n.

   This document also introduces a new registry for sub-TLVs of the
   Reverse Metric TLV.  The registration policy is Expert Review as
   defined in [RFC8126].  This registry is part of the "IS-IS TLV
   Codepoints" registry.  The name of the registry is "Sub-TLVs for
   Reverse Metric TLV".  The defined values are:

      0:       Reserved
      1-17:    Unassigned
      18:      Traffic Engineering Metric sub-TLV, as specified in this
               document (Section 2)
      19-255:  Unassigned

6.  Acknowledgments

   The authors would like to thank Mike Shand, Dave Katz, Guan Deng,
   Ilya Varlashkin, Jay Chen, Les Ginsberg, Peter Ashwood-Smith, Uma
   Chunduri, Alexander Okonnikov, Jonathan Harrison, Dave Ward, Himanshu
   Shah, Wes George, Danny McPherson, Ed Crabbe, Russ White, Robert
   Razsuk, Tom Petch and Acee Lindem for their comments and
   contributions.

   This document was produced using Marshall Rose's xml2rfc tool.

7.  References

7.1.  Normative References

   [ISO10589]
              ISO, "Intermediate system to Intermediate system routeing
              information exchange protocol for use in conjunction with
              the Protocol for providing the Connectionless-mode Network
              Service (ISO 8473)", ISO/IEC 10589:2002.

   [RFC1195]  Callon, R., "Use of OSI IS-IS for routing in TCP/IP and
              dual environments", RFC 1195, DOI 10.17487/RFC1195,
              December 1990, <https://www.rfc-editor.org/info/rfc1195>.

Shen, et al.             Expires April 19, 2019                [Page 10]
Internet-Draft            IS-IS Reverse Metric              October 2018

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997, <https://www.rfc-
              editor.org/info/rfc2119>.

   [RFC5120]  Przygienda, T., Shen, N., and N. Sheth, "M-ISIS: Multi
              Topology (MT) Routing in Intermediate System to
              Intermediate Systems (IS-ISs)", RFC 5120,
              DOI 10.17487/RFC5120, February 2008, <https://www.rfc-
              editor.org/info/rfc5120>.

   [RFC5305]  Li, T. and H. Smit, "IS-IS Extensions for Traffic
              Engineering", RFC 5305, DOI 10.17487/RFC5305, October
              2008, <https://www.rfc-editor.org/info/rfc5305>.

   [RFC5443]  Jork, M., Atlas, A., and L. Fang, "LDP IGP
              Synchronization", RFC 5443, DOI 10.17487/RFC5443, March
              2009, <https://www.rfc-editor.org/info/rfc5443>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

7.2.  Informative References

   [I-D.shen-isis-spine-leaf-ext]
              Shen, N., Ginsberg, L., and S. Thyamagundalu, "IS-IS
              Routing for Spine-Leaf Topology", draft-shen-isis-spine-
              leaf-ext-03 (work in progress), March 2017.

   [RFC5304]  Li, T. and R. Atkinson, "IS-IS Cryptographic
              Authentication", RFC 5304, DOI 10.17487/RFC5304, October
              2008, <https://www.rfc-editor.org/info/rfc5304>.

   [RFC5310]  Bhatia, M., Manral, V., Li, T., Atkinson, R., White, R.,
              and M. Fanto, "IS-IS Generic Cryptographic
              Authentication", RFC 5310, DOI 10.17487/RFC5310, February
              2009, <https://www.rfc-editor.org/info/rfc5310>.

   [RFC5817]  Ali, Z., Vasseur, JP., Zamfir, A., and J. Newton,
              "Graceful Shutdown in MPLS and Generalized MPLS Traffic
              Engineering Networks", RFC 5817, DOI 10.17487/RFC5817,
              April 2010, <https://www.rfc-editor.org/info/rfc5817>.

Shen, et al.             Expires April 19, 2019                [Page 11]
Internet-Draft            IS-IS Reverse Metric              October 2018

   [RFC5919]  Asati, R., Mohapatra, P., Chen, E., and B. Thomas,
              "Signaling LDP Label Advertisement Completion", RFC 5919,
              DOI 10.17487/RFC5919, August 2010, <https://www.rfc-
              editor.org/info/rfc5919>.

   [RFC6138]  Kini, S., Ed. and W. Lu, Ed., "LDP IGP Synchronization for
              Broadcast Networks", RFC 6138, DOI 10.17487/RFC6138,
              February 2011, <https://www.rfc-editor.org/info/rfc6138>.

   [RFC7645]  Chunduri, U., Tian, A., and W. Lu, "The Keying and
              Authentication for Routing Protocol (KARP) IS-IS Security
              Analysis", RFC 7645, DOI 10.17487/RFC7645, September 2015,
              <https://www.rfc-editor.org/info/rfc7645>.

Appendix A.  Node Isolation Challenges

   On rare occasions, it is necessary for an operator to perform
   disruptive network maintenance on an entire IS-IS router node, i.e.,
   major software upgrades, power/cooling augments, etc.  In these
   cases, an operator will set the IS-IS Overload Bit (OL-bit) within
   the Link State Protocol Data Units (LSPs) of the IS-IS router about
   to undergo maintenance.  The IS-IS router immediately floods its
   updated LSPs to all IS-IS routers in the IS-IS domain.  Upon receipt
   of the updated LSPs, all IS-IS routers recalculate their Shortest
   Path First (SPF) tree excluding IS-IS routers whose LSPs have the OL-
   bit set.  This effectively removes the IS-IS router about to undergo
   maintenance from the topology, thus preventing it from receiving any
   transit traffic during the maintenance period.

   After the maintenance activity has completed, the operator resets the
   IS-IS Overload Bit within the LSPs of the original IS-IS router
   causing it to flood updated IS-IS LSPs throughout the IS-IS domain.
   All IS-IS routers recalculate their SPF tree and now include the
   original IS-IS router in their topology calculations, allowing it to
   be used for transit traffic again.

   Isolating an entire IS-IS router from the topology can be especially
   disruptive due to the displacement of a large volume of traffic
   through an entire IS-IS router to other, sub-optimal paths, (e.g.,
   those with significantly larger delay).  Thus, in the majority of
   network maintenance scenarios, where only a single link or LAN needs
   to be augmented to increase its physical capacity or is experiencing
   an intermittent failure, it is much more common and desirable to
   gracefully remove just the targeted link or LAN from service,
   temporarily, so that the least amount of user-data traffic is
   affected during the link-specific network maintenance.

Shen, et al.             Expires April 19, 2019                [Page 12]
Internet-Draft            IS-IS Reverse Metric              October 2018

Appendix B.  Link Isolation Challenges

   Before network maintenance events are performed on individual
   physical links or LANs, operators substantially increase the IS-IS
   metric simultaneously on both devices attached to the same link or
   LAN.  In doing so, the devices generate new Link State Protocol Data
   Units (LSPs) that are flooded throughout the network and cause all
   routers to gradually shift traffic onto alternate paths with very
   little or no disruption to in-flight communications by applications
   or end-users.  When performed successfully, this allows the operator
   to confidently perform disruptive augmentation, fault diagnosis or
   repairs on a link without disturbing ongoing communications in the
   network.

   There are a number of challenges with the above solution.  First, it
   is quite common to have routers with several hundred interfaces and
   individual interfaces that are from several hundred Gigabits/second
   to Terabits/second of traffic.  Thus, it is imperative that operators
   accurately identify the same point-to-point link on two, separate
   devices in order to increase (and, afterward, decrease) the IS-IS
   metric appropriately.  Second, the aforementioned solution is very
   time consuming and even more error-prone to perform when it's
   necessary to temporarily remove a multi-access LAN from the network
   topology.  Specifically, the operator needs to configure ALL devices
   that have interfaces attached to the multi-access LAN with an
   appropriately high IS-IS metric, (and then decrease the IS-IS metric
   to its original value afterward).  Finally, with respect to multi-
   access LANs, there is currently no method to bidirectionally isolate
   only a single node's interface on the LAN when performing more fine-
   grained diagnosis and repairs to the multi-access LAN.

   In theory, use of a Network Management System (NMS) could improve the
   accuracy of identifying the appropriate subset of routers attached to
   either a point-to-point link or a multi-access LAN as well as
   signaling from the NMS to those devices, using a network management
   protocol to adjust the IS-IS metrics on the pertinent set of
   interfaces.  The reality is that NMSs are, to a very large extent,
   not used within Service Provider's networks for a variety of reasons.
   In particular, NMSs do not interoperate very well across different
   vendors or even separate platform families within the same vendor.

   The risks of misidentifying one side of a point-to-point link or one
   or more interfaces attached to a multi-access LAN and subsequently
   increasing its IS-IS metric and potentially increased latency, jitter
   or packet loss.  This is unacceptable given the necessary performance
   requirements for a variety of reasons including the customer
   perception for near lossless operations and the associated demanding
   Service Level Agreement's (SLAs) for all network services.

Shen, et al.             Expires April 19, 2019                [Page 13]
Internet-Draft            IS-IS Reverse Metric              October 2018

Appendix C.  Contributors' Addresses

   Tony Li

   Email: tony.li@tony.li

Authors' Addresses

   Naiming Shen
   Cisco Systems
   560 McCarthy Blvd.
   Milpitas, CA  95035
   USA

   Email: naiming@cisco.com

   Shane Amante
   Apple, Inc.
   1 Infinite Loop
   Cupertino, CA  95014
   USA

   Email: samante@apple.com

   Mikael Abrahamsson
   T-Systems Nordic
   Kistagangen 26
   Stockholm
   SE

   Email: Mikael.Abrahamsson@t-systems.se

Shen, et al.             Expires April 19, 2019                [Page 14]