Skip to main content

Transmission of IPv6 over IPv4 Domains without Explicit Tunnels
draft-ietf-ipngwg-6over4-02

The information below is for an old version of the document that is already published as an RFC.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 2529.
Authors Cyndi Jung , Brian E. Carpenter
Last updated 2013-03-02 (Latest revision 1999-01-19)
RFC stream Internet Engineering Task Force (IETF)
Intended RFC status Proposed Standard
Formats
Additional resources Mailing list discussion
Stream WG state (None)
Document shepherd (None)
IESG IESG state Became RFC 2529 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-ipngwg-6over4-02
IETF                                              B. Carpenter, IBM
Internet Draft                                        C. Jung, 3Com
January  1998

    Transmission of IPv6 over IPv4 Domains without Explicit Tunnels

                    draft-ietf-ipngwg-6over4-02.txt
               
    
Status of this Memo

     This document is an Internet-Draft.  Internet-Drafts are working
     documents of the Internet Engineering Task Force (IETF), its
     areas, and its working groups.  Note that other groups may also
     distribute working documents as Internet-Drafts.

     Internet-Drafts are draft documents valid for a maximum of six
     months and may be updated, replaced, or obsoleted by other
     documents at any time.  It is inappropriate to use Internet-
     Drafts as reference material or to cite them other than as
     "work in progress."

     To view the entire list of current Internet-Drafts, please check
     the "1id-abstracts.txt" listing contained in the Internet-Drafts
     Shadow Directories on ftp.is.co.za (Africa), ftp.nordu.net
     (Northern Europe), ftp.nis.garr.it (Southern Europe), munnari.oz.au
     (Pacific Rim), ftp.ietf.org (US East Coast), or ftp.isi.edu
     (US West Coast).

Copyright Notice

   Copyright (C) The Internet Society (1998).  All Rights Reserved.

Abstract

   This memo specifies the frame format for transmission of IPv6 [IPV6]
   packets and the method of forming IPv6 link-local addresses over IPv4
   domains.  It also specifies the content of the Source/Target Link-
   layer Address option used in the Router Solicitation, Router
   Advertisement, Neighbor Solicitation, and Neighbor Advertisement
   and Redirect messages, when those messages are transmitted on an
   IPv4 multicast network.
 
   The motivation for this method is to allow isolated IPv6 hosts,
   located on a physical link which has no directly connected IPv6
   router, to become fully functional IPv6 hosts by using an IPv4
   domain that supports IPv4 multicast as their virtual local
   link. It uses IPv4 multicast as a "virtual Ethernet."
 
 

Carpenter, Jung                Expires July   1999             [Page 1]
^L                                                                  

Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

Table of Contents:

   1. Introduction....................................................2
   2. Maximum Transmission Unit.......................................3
   3. Frame Format....................................................3
   4. Stateless Autoconfiguration and Link-Local Addresses............4
   5. Address Mapping -- Unicast......................................4
   6. Address Mapping -- Multicast....................................5
   7. Scaling and Transition Isues....................................5
   8. IANA considerations.............................................6
   9. Security considerations.........................................6
   Acknowledgements...................................................7
   References.........................................................7
   APPENDIX A: IPv4 Multicast Addresses for Neighbor Discovery........8
   Authors' Addresses.................................................9
   Full Copyright Notice..............................................9

1. Introduction

   This memo specifies the frame format for transmission of IPv6 [IPV6]
   packets and the method of forming IPv6 link-local addresses over IPv4
   multicast "domains".  For the purposes of this document, an IPv4 domain 
   is a fully interconnected set of IPv4 subnets, within the same local 
   multicast scope, on which there are at least two IPv6 nodes conforming 
   to this specification.  This IPv4 domain could form part of the
   globally-unique IPv4 address space, or could form part of a private 
   IPv4 network [RFC 1918]. 

   This memo also specifies the content of the Source/Target Link-layer
   Address option used in the Router Solicitation, Router Advertisement,
   Neighbor Solicitation, Neighbor Advertisement and Redirect messages 
   described in [DISC], when those messages are transmitted on an IPv4 
   multicast domain.

   The motivation for this method is to allow isolated IPv6 hosts,
   located on a physical link which has no directly connected IPv6
   router, to become fully functional IPv6 hosts by using an IPv4 multicast
   domain as their virtual local link.  Thus, at least one IPv6 router 
   using the same method must be connected to the same IPv4 domain if 
   IPv6 routing to other links is required.

   IPv6 hosts connected using this method do not require IPv4-compatible
   addresses or configured tunnels.  In this way IPv6 gains considerable
   independence of the underlying links and can step over many hops of
   IPv4 subnets. The mechanism is known formally as "IPv6 over IPv4"
   or "6over4" and colloquially as "virtual Ethernet."

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED",  "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

Carpenter, Jung                Expires July   1999             [Page 2]
^L  

Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

2. Maximum Transmission Unit

   The default MTU size for IPv6 packets on an IPv4 domain is 1480
   octets.  This size may be varied by a Router Advertisement [DISC]
   containing an MTU option which specifies a different MTU, or by
   manual configuration of each node.

   Note that if by chance the IPv6 MTU size proves to be too large for
   some intermediate IPv4 subnet, IPv4 fragmentation will ensue.  While
   undesirable, this is not disastrous. However, the IPv4 "do not fragment"
   bit MUST NOT be set in the encapsulating IPv4 header.

3. Frame Format

   IPv6 packets are transmitted in IPv4 packets [RFC 791] with an IPv4
   protocol type of 41, the same as has been assigned in [RFC 1933] for
   IPv6 packets that are tunneled inside of IPv4 frames.  The IPv4
   header contains the Destination and Source IPv4 addresses.  The IPv4
   packet body contains the IPv6 header followed immediately by the
   payload.

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |Version|  IHL  |Type of Service|          Total Length         |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |         Identification        |Flags|      Fragment Offset    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Time to Live | Protocol 41   |         Header Checksum       |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                       Source Address                          |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    Destination Address                        |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                    Options                    |    Padding    |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |            IPv6 header and payload ...              /
    +-------+-------+-------+-------+-------+------+------+

   If there are IPv4 options, then padding SHOULD be added to the IPv4
   header such that the IPv6 header starts on a boundary that is a 32-
   bit offset from the end of the datalink header.

   The Time to Live field SHOULD be set to a low value, to prevent such
   packets accidentally leaking from the IPv4 domain.  This MUST be a
   configurable parameter, with a recommended default of 8.

Carpenter, Jung                Expires July   1999             [Page 3]
^L

                                                             
Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

4. Stateless Autoconfiguration and Link-Local Addresses

   The Interface Identifier [AARCH] of an IPv4 interface is the 32-bit 
   IPv4 address of that interface, with the octets in the same order in 
   which they would appear in the header of an IPv4 packet, padded at 
   the left with zeros to a total of 64 bits.  Note that the "Universal/
   Local" bit is zero, indicating that the Interface Identifer is not 
   globally unique.  When the host has more than one IPv4 address in use 
   on the physical interface concerned, an administrative choice of one 
   of these IPv4 addresses is made.

   An IPv6 address prefix used for stateless autoconfiguration [CONF] of 
   an IPv4 interface MUST have a length of 64 bits except for a special
   case mentioned in Section 7.

   The IPv6 Link-local address [AARCH] for an IPv4 virtual interface is
   formed by appending the Interface Identifier, as defined above, to 
   the prefix FE80::/64.

    +-------+-------+-------+-------+-------+-------+------+------+
    |  FE      80      00      00      00      00      00     00  |
    +-------+-------+-------+-------+-------+-------+------+------+
    |  00      00   |  00   |  00   |   IPv4 Address              |
    +-------+-------+-------+-------+-------+-------+------+------+

5. Address Mapping -- Unicast

   The procedure for mapping IPv6 addresses into IPv4 virtual link-layer
   addresses is described in [DISC].  The Source/Target Link-layer
   Address option has the following form when the link layer is IPv4.
   Since the length field is in units of 8 bytes, the value below is 1.

    +-------+-------+-------+-------+-------+-------+-------+-------+
    | Type  |Length | must be zero  |        IPv4 Address           |
    +-------+-------+-------+-------+-------+-------+-------+-------+

   Type:
    1 for Source Link-layer address.
    2 for Target Link-layer address.

   Length:
    1 (in units of 8 octets).

   IPv4 Address:

   The 32 bit IPv4 address, in network byte order.  This is the address
   the interface currently responds to, and may be different from the
   Interface Identifier for stateless autoconfiguration.

Carpenter, Jung                Expires July   1999             [Page 4]
^L

                                                                     
Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

6. Address Mapping -- Multicast

   IPv4 multicast MUST be available. An IPv6 packet with a multicast
   destination address DST MUST be transmitted to the IPv4 multicast
   address of Organization-Local Scope using the mapping below.  These
   IPv4 multicast addresses SHOULD be taken from the block 239.192.0.0/16,
   a sub-block of the Organization-Local Scope address block, or, if 
   all of those are not available, from the expansion blocks 
   defined in [ADMIN].  Note that when they are formed 
   using the expansion blocks, they use only a /16 sized block.

        +-------+-------+-------+-------+       
        |  239  |  OLS  | DST14 | DST15 |
        +-------+-------+-------+-------+

        DST14, DST15        last two bytes of IPv6 multicast address.

        OLS                 from the configured Organization-Local
                            Scope address block.  SHOULD be 192,
                            see [ADMIN] for details.

   No new IANA registration procedures are required for the above.
   See appendix A. for a list of all the multicast groups that must be
   joined to support Neighbor Discovery.

7. Scaling and Transition Issues

   The multicast mechanism described in Section 6 above appears to have
   essentially the same scaling properties as native IPv6 over most
   media, except for the slight reduction in MTU size which will
   slightly reduce bulk throughput.  On an ATM network, where IPv4
   multicast relies on relatively complex mechanisms, it is to be
   expected that IPv6 over IPv4 over ATM will perform less well than
   native IPv6 over ATM.

   The "IPv6 over IPv4" mechanism is intended to take its place in the
   range of options available for transition from IPv4 to IPv6.  In
   particular it allows a site to run both IPv4 and IPv6 in coexistence,
   without having to configure IPv6 hosts either with IPv4-compatible
   addresses or with tunnels.  Interfaces of the IPv6 router and hosts
   will of course need to be enabled in "6over4" mode. 

   A site may choose to start its IPv6 transition by configuring one
   IPv6 router to support "6over4" on an interface connected to
   the site's IPv4 domain, and another IPv6 format on an interface
   connected to the IPv6 Internet.  Any enabled "6over4" hosts
   in the IPv4 domain will then be able to communicate both with the
   router and with the IPv6 Internet, without manual configuration of a
   tunnel and without the need for an IPv4-compatible IPv6 address,
   either stateless or stateful address configuration providing the IPv6
   address to the IPv6 host.

Carpenter, Jung                Expires July   1999             [Page 5]
^L

                                                                     
Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

   During transition, routers may need to advertise at least two 
   IPv6 prefixes, one for the native LAN (e.g. Ethernet) and one for 
   "6over4." As with any IPv6 prefix assigned to an IPv6 subnet, the 
   latter MUST be unique within its scope, whether site-local or  
   global addressing is used.

   Also note that when a router is handling both native LAN and
   "6over4" on the same physical interface,  during
   stateless autoconfiguration, there is a period when IPv6 link-local  
   addresses are used, in both cases with the prefix FE80::/64. 
   Note that the prefix-length for these link-local adddress MUST
   then be 128 so that the two cases can be distinguished.

   As the site installs additional IPv6 routers, "6over4" hosts
   which become physically adjacent to IPv6 routers can be changed to
   run as native IPv6 hosts, with the the only impact on IPv6
   applications being a slight increase in MTU size. At some stage
   during transition, it might be convenient to dual home hosts
   in both native LAN and "6over4" mode, but this is not required.

8. IANA considerations

   No assignments by the IANA are required beyond those in [ADMIN].

9. Security considerations

   Implementors should be aware that, in addition to posssible attacks
   against IPv6, security attacks against IPv4 must also be considered.
   Use of IP security at both IPv4 and IPv6 levels should nevertheless
   be avoided, for efficiency reasons.  For example, if IPv6 is running
   encrypted, encryption of IPv4 would be redundant except if traffic
   analysis is felt to be a threat.  If IPv6 is running authenticated,
   then authentication of IPv4 will add little.  Conversely, IPv4
   security will not protect IPv6 traffic once it leaves the IPv6-over-
   IPv4 domain.  Therefore, implementing IPv6 security is required even
   if IPv4 security is available.

   There is a possible spoofing attack in which spurious 6over4
   packets are injected into a 6over4 domain from outside. Thus,
   boundary routers MUST discard multicast IPv4 packets with source 
   or destination multicast addresses of organisation local scope
   as defined in section 6 above, if they arrive on physical
   interfaces outside that scope. To defend against spurious
   unicast 6over4 packets, boundary routers MUST discard incoming
   IPv4 packets with protocol type 41 from unknown sources, i.e.
   IPv6-in-IPv4 tunnels must only be accepted from trusted sources.
   Unless IPSEC authentication is available, the RECOMMENDED technique
   for this is to configure the boundary router only to accept
   protocol type 41 packets from source addresses within a trusted
   range or ranges.

Carpenter, Jung                Expires July   1999             [Page 6]
^L 

                                                                    
Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

 

Acknowledgements

   The basic idea presented above is not original, and we have had
   invaluable comments from Matt Crawford, Steve Deering, Dan
   Harrington, Rich Draves, Erik Nordmark, Quang Nguyen, Thomas
   Narten, and other members of the IPNG and NGTRANS working groups.

   This document is seriously ripped off from RFC 1972 written by
   Matt Crawford. Brian Carpenter was at CERN when the work was started.

References

   [AARCH]    Hinden, R., and S. Deering, "IP Version 6 Addressing
              Architecture", RFC 2373

   [ADMIN]    Meyer, D., "Administratively Scoped IP Multicast",
              RFC 2365, BCP 23.

   [CONF]     Thomson, S., and T. Narten, "IPv6 Stateless Address
              Autoconfiguration", RFC 2462 

   [DISC]     Narten, T., Nordmark, E., and W. Simpson, "Neighbor
              Discovery for IP Version 6 (IPv6)", RFC 2461 

   [IPV6]     Deering, S., and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", RFC 2460

   [RFC 791]  Postel, J., "Internet Protocol", RFC 791

   [RFC 1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., de Groot, G.,
              Lear, E., "Address Allocation for Private Internets",
              RFC 1918

   [RFC 1933] Gilligan, R., and Nordmark, E., "Transition Mechanisms for 
              IPv6 Hosts and Routers", RFC 1933

   [RFC 2119] Key words for use in RFCs to Indicate Requirement Levels.
              S. Bradner, RFC 2119

Carpenter, Jung                Expires July   1999             [Page 7]
^L

                                                                     
Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

APPENDIX A:  IPv4 Multicast Addresses for Neighbor Discovery

   The following IPv4 multicast groups are used to support Neighbor
   Discovery with this specification. The IPv4 addresses listed
   in this section were obtained by looking at the IPv6 multicast
   addresses that Neigbour Discovery uses, and deriving the resulting 
   IPv4 "virtual link-layer" addresses that are generated from them
   using the algorithm given in Section 6.

   all-nodes multicast address
         - the administratively-scoped IPv4 multicast address used to 
           reach all nodes in the local IPv4 domain supporting this 
           specification.  239.OLS.0.1

   all-routers multicast address
         - the administratively-scoped IPv4 multicast address to reach 
           all routers in the local IPv4 domain supporting this 
           specification.  239.OLS.0.2

   solicited-node multicast address
         - an administratively scoped multicast address that is computed 
           as a function of the solicited target's address by taking the 
           low-order 24 bits of the IPv4 address used to form the IPv6 
           address, and prepending the prefix FF02:0:0:0:0:1:FF00::/104
           [AARCH]. This is then mapped to the IPv4 
           multicast address by the method described in this document.  
           For example, if the IPv4 address used to form the IPv6 address 
           is W.X.Y.Z, then the IPv6 solicited node multicast address is 
           FF02::1:255.X.Y.Z and the corresponding IPv4 multicast address is 
           239.OLS.Y.Z

Carpenter, Jung                Expires July   1999             [Page 8]
^L

                                                                     
Internet Draft   Transmission of IPv6 Packets over IPv4      Jan   1999

Authors' Addresses

      Brian E. Carpenter
      Internet Division
      IBM United Kingdom Laboratories
      MP 185, Hursley Park
      Winchester, Hampshire S021 2JN, UK

      Email: brian@hursley.ibm.com

      Cyndi Jung
      3Com Corporation
      5400 Bayfront Plaza, Mailstop 3219
      Santa Clara, California  95052-8145

      Email: cmj@3Com.com

Full Copyright Statement

   Copyright (C) The Internet Society (1998).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Carpenter, Jung                Expires July   1999             [Page 9]
^L