Skip to main content

Using EAP-TLS with TLS 1.3
draft-ietf-emu-eap-tls13-05

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 9190.
Authors John Preuß Mattsson , Mohit Sethi
Last updated 2019-07-22 (Latest revision 2019-05-26)
Replaces draft-mattsson-eap-tls13
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state Waiting for WG Chair Go-Ahead
Revised I-D Needed - Issue raised by WGLC, Doc Shepherd Follow-up Underway
Document shepherd (None)
IESG IESG state Became RFC 9190 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-emu-eap-tls13-05
Network Working Group                                        J. Mattsson
Internet-Draft                                                  M. Sethi
Updates: 5216 (if approved)                                     Ericsson
Intended status: Standards Track                            May 26, 2019
Expires: November 27, 2019

                       Using EAP-TLS with TLS 1.3
                      draft-ietf-emu-eap-tls13-05

Abstract

   This document specifies the use of EAP-TLS with TLS 1.3 while
   remaining backwards compatible with existing implementations of EAP-
   TLS.  TLS 1.3 provides significantly improved security, privacy, and
   reduced latency when compared to earlier versions of TLS.  EAP-TLS
   with TLS 1.3 further improves security and privacy by mandating use
   of privacy and revocation checking.  This document updates RFC 5216.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on November 27, 2019.

Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of

Mattsson & Sethi        Expires November 27, 2019               [Page 1]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
     1.1.  Requirements and Terminology  . . . . . . . . . . . . . .   3
   2.  Protocol Overview . . . . . . . . . . . . . . . . . . . . . .   4
     2.1.  Overview of the EAP-TLS Conversation  . . . . . . . . . .   4
       2.1.1.  Mutual Authentication . . . . . . . . . . . . . . . .   4
       2.1.2.  Termination . . . . . . . . . . . . . . . . . . . . .   5
       2.1.3.  No Peer Authentication  . . . . . . . . . . . . . . .   8
       2.1.4.  Hello Retry Request . . . . . . . . . . . . . . . . .   9
       2.1.5.  Ticket Establishment  . . . . . . . . . . . . . . . .  10
       2.1.6.  Resumption  . . . . . . . . . . . . . . . . . . . . .  11
       2.1.7.  Privacy . . . . . . . . . . . . . . . . . . . . . . .  13
       2.1.8.  Fragmentation . . . . . . . . . . . . . . . . . . . .  13
     2.2.  Identity Verification . . . . . . . . . . . . . . . . . .  14
     2.3.  Key Hierarchy . . . . . . . . . . . . . . . . . . . . . .  14
     2.4.  Parameter Negotiation and Compliance Requirements . . . .  15
     2.5.  EAP State Machines  . . . . . . . . . . . . . . . . . . .  16
   3.  Detailed Description of the EAP-TLS Protocol  . . . . . . . .  16
   4.  IANA considerations . . . . . . . . . . . . . . . . . . . . .  16
   5.  Security Considerations . . . . . . . . . . . . . . . . . . .  17
     5.1.  Security Claims . . . . . . . . . . . . . . . . . . . . .  17
     5.2.  Peer and Server Identities  . . . . . . . . . . . . . . .  17
     5.3.  Certificate Validation  . . . . . . . . . . . . . . . . .  17
     5.4.  Certificate Revocation  . . . . . . . . . . . . . . . . .  17
     5.5.  Packet Modification Attacks . . . . . . . . . . . . . . .  18
     5.6.  Authorization . . . . . . . . . . . . . . . . . . . . . .  18
     5.7.  Resumption  . . . . . . . . . . . . . . . . . . . . . . .  19
     5.8.  Privacy Considerations  . . . . . . . . . . . . . . . . .  20
     5.9.  Pervasive Monitoring  . . . . . . . . . . . . . . . . . .  21
     5.10. Discovered Vulnerabilities  . . . . . . . . . . . . . . .  21
   6.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  22
     6.1.  Normative References  . . . . . . . . . . . . . . . . . .  22
     6.2.  Informative references  . . . . . . . . . . . . . . . . .  23
   Appendix A.  Updated references . . . . . . . . . . . . . . . . .  26
   Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . .  26
   Contributors  . . . . . . . . . . . . . . . . . . . . . . . . . .  26
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  26

1.  Introduction

   The Extensible Authentication Protocol (EAP), defined in [RFC3748],
   provides a standard mechanism for support of multiple authentication
   methods.  EAP-Transport Layer Security (EAP-TLS) [RFC5216] specifies
   an EAP authentication method with certificate-based mutual

Mattsson & Sethi        Expires November 27, 2019               [Page 2]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   authentication and key derivation utilizing the TLS handshake
   protocol for cryptographic algorithms and protocol version
   negotiation, mutual authentication, and establishment of shared
   secret keying material.  EAP-TLS is widely supported for
   authentication in IEEE 802.11 [IEEE-802.11] networks (Wi-Fi) using
   IEEE 802.1X [IEEE-802.1X] and it's the default mechanism for
   certificate based authentication in 3GPP 5G [TS.33.501] and MulteFire
   [MulteFire] networks.  EAP-TLS [RFC5216] references TLS 1.0 [RFC2246]
   and TLS 1.1 [RFC4346], but works perfectly also with TLS 1.2
   [RFC5246].  TLS 1.0 and 1.1 are formally deprecated and prohibited to
   negotiate and use [I-D.ietf-tls-oldversions-deprecate].

   Weaknesses found in TLS 1.2, as well as new requirements for
   security, privacy, and reduced latency has led to the specification
   of TLS 1.3 [RFC8446], which obsoletes TLS 1.2 [RFC5246].  TLS 1.3 is
   in large parts a complete remodeling of the TLS handshake protocol
   including a different message flow, different handshake messages,
   different key schedule, different cipher suites, different
   resumption, and different privacy protection.  This means that
   significant parts of the normative text in the previous EAP-TLS
   specification [RFC5216] are not applicable to EAP-TLS with TLS 1.3
   (or higher).  Therefore, aspects such as resumption, privacy
   handling, and key derivation need to be appropriately addressed for
   EAP-TLS with TLS 1.3 (or higher).

   This document defines how to use EAP-TLS with TLS 1.3 (or higher) and
   does not change how EAP-TLS is used with older versions of TLS.
   While this document updates EAP-TLS [RFC5216], it remains backwards
   compatible with it and existing implementations of EAP-TLS.  This
   document only describes differences compared to [RFC5216].

   In addition to the improved security and privacy offered by TLS 1.3,
   there are other significant benefits of using EAP-TLS with TLS 1.3.
   Privacy is mandatory and achieved without any additional round-trips,
   revocation checking is mandatory and easy with OCSP stapling, and TLS
   1.3 introduces more possibilities to reduce fragmentation when
   compared to earlier versions of TLS.

1.1.  Requirements and Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED","MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

   Readers are expected to be familiar with the terms and concepts used
   in EAP-TLS [RFC5216] and TLS [RFC8446].

Mattsson & Sethi        Expires November 27, 2019               [Page 3]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

2.  Protocol Overview

2.1.  Overview of the EAP-TLS Conversation

   TLS 1.3 changes both the message flow and the handshake messages
   compared to earlier versions of TLS.  Therefore, much of Section 2.1
   of [RFC5216] does not apply for TLS 1.3 (or higher).

   After receiving an EAP-Request packet with EAP-Type=EAP-TLS as
   described in [RFC5216] the conversation will continue with the TLS
   handshake protocol encapsulated in the data fields of EAP-Response
   and EAP-Request packets.  When EAP-TLS is used with TLS version 1.3
   or higher, the formatting and processing of the TLS handshake SHALL
   be done as specified in that version of TLS.  This document only
   lists additional and different requirements, restrictions, and
   processing compared to [RFC8446] and [RFC5216].

2.1.1.  Mutual Authentication

   The EAP server MUST authenticate with a certificate and SHOULD
   require the EAP peer to authenticate with a certificate.
   Certificates can be of any type supported by TLS including raw public
   keys.  Pre-Shared Key (PSK) authentication SHALL NOT be used except
   for resumption.  SessionID is deprecated in TLS 1.3 and the EAP
   server SHALL ignore the legacy_session_id field if TLS 1.3 is
   negotiated.  TLS 1.3 introduced early application data which is not
   used in EAP-TLS.  A server which receives an "early_data" extension
   MUST ignore the extension or respond with a HelloRetryRequest as
   described in Section 4.2.10 of [RFC8446].  Resumption is handled as
   described in Section 2.1.6.  After the TLS handshake has completed
   and all Post-Handshake messages have been sent, the EAP server sends
   EAP-Success.

   In the case where EAP-TLS with mutual authentication is successful,
   the conversation will appear as shown in Figure 1.  The EAP server
   commits to not send any more handshake messages by sending an empty
   TLS record, see Section 2.5.

Mattsson & Sethi        Expires November 27, 2019               [Page 4]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                                    (TLS ServerHello,
                                             TLS EncryptedExtensions,
                                              TLS CertificateRequest,
                                                     TLS Certificate,
                                               TLS CertificateVerify,
                                                        TLS Finished,
                                 <--------          TLS empty record)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS Certificate,
    TLS CertificateVerify,
    TLS Finished)                -------->
                                 <--------               EAP-Success

                  Figure 1: EAP-TLS mutual authentication

2.1.2.  Termination

   TLS 1.3 changes both the message flow and the handshake messages
   compared to earlier versions of TLS.  Therefore, some normative text
   in Section 2.1.3 of [RFC5216] does not apply for TLS 1.3 or higher.
   The two paragraphs below replaces the corresponding paragraphs in
   Section 2.1.3 of [RFC5216] when EAP-TLS is used with TLS 1.3 or
   higher.  The other paragraphs in Section 2.1.3 of [RFC5216] still
   apply with the exception that SessionID is deprecated.

      If the EAP server authenticates successfully, the EAP peer MUST
      send an EAP-Response message with EAP-Type=EAP-TLS containing TLS
      records conforming to the version of TLS used.

      If the EAP peer authenticates successfully, the EAP server MUST
      send an EAP-Request packet with EAP-Type=EAP-TLS containing TLS
      records conforming to the version of TLS used.  The message flow
      ends with the EAP server sending an EAP-Success message.

Mattsson & Sethi        Expires November 27, 2019               [Page 5]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   Figures 2, 3, and 4 illustrate message flows in several cases where
   the EAP peer or EAP server sends a TLS fatal alert message.  TLS
   warning alerts generally mean that the connection can continue
   normally and does not change the message flow.  Note that the party
   receiving a TLS warning alert may choose to terminate the connection
   by sending a TLS fatal alert, which may add an extra round-trip, see
   [RFC8446].

   In the case where the server rejects the ClientHello, the
   conversation will appear as shown in Figure 2.

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------          (TLS Fatal Alert)
    EAP-Response/
    EAP-Type=EAP-TLS             -------->
                                 <--------               EAP-Failure

             Figure 2: EAP-TLS server rejection of ClientHello

   In the case where server authentication is unsuccessful, the
   conversation will appear as shown in Figure 3.

Mattsson & Sethi        Expires November 27, 2019               [Page 6]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                                    (TLS ServerHello,
                                             TLS EncryptedExtensions,
                                              TLS CertificateRequest,
                                                     TLS Certificate,
                                               TLS CertificateVerify,
                                                        TLS Finished,
                                 <--------          TLS empty record)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS Fatal Alert)
                                 -------->
                                 <--------               EAP-Failure

           Figure 3: EAP-TLS unsuccessful server authentication

   In the case where the server authenticates to the peer successfully,
   but the peer fails to authenticate to the server, the conversation
   will appear as shown in Figure 4.

Mattsson & Sethi        Expires November 27, 2019               [Page 7]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->

                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                                    (TLS ServerHello,
                                             TLS EncryptedExtensions,
                                              TLS CertificateRequest,
                                                     TLS Certificate,
                                               TLS CertificateVerify,
                                                        TLS Finished,
                                 <--------          TLS empty record)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS Certificate,
    TLS CertificateVerify,
    TLS Finished)                -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------          (TLS Fatal Alert)
    EAP-Response/
    EAP-Type=EAP-TLS             -------->
                                 <--------               EAP-Failure

           Figure 4: EAP-TLS unsuccessful client authentication

2.1.3.  No Peer Authentication

   In the case where EAP-TLS is used without peer authentication (e.g.,
   emergency services, as described in [RFC7406]) the conversation will
   appear as shown in Figure 5.

Mattsson & Sethi        Expires November 27, 2019               [Page 8]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                                    (TLS ServerHello,
                                             TLS EncryptedExtensions,
                                                     TLS Certificate,
                                               TLS CertificateVerify,
                                                        TLS Finished,
                                 <--------          TLS empty record)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS Finished)                -------->
                                 <--------               EAP-Success

               Figure 5: EAP-TLS without peer authentication

2.1.4.  Hello Retry Request

   TLS 1.3 [RFC8446] defines that TLS servers can send a
   HelloRetryRequest message in response to a ClientHello if the server
   finds an acceptable set of parameters but the initial ClientHello
   does not contain all the needed information to continue the
   handshake.

   An EAP-TLS peer and server SHOULD support the use of
   HelloRetryRequest message.  As noted in Section 4.1.4 of [RFC8446],
   the server MUST provide the supported_versions extensions and SHOULD
   contain the minimal set of extensions necessary for the client to
   generate a correct ClientHello pair.  A HelloRetryRequest MUST NOT
   contain any extensions that were not first offered by the client in
   its ClientHello, with the exception of optionally the cookie
   extension.

   The case of a successful EAP-TLS mutual authentication after the
   server has sent a HelloRetryRequest message is shown in Figure 6.
   Note the extra round-trip as a result of the HelloRetryRequest.

Mattsson & Sethi        Expires November 27, 2019               [Page 9]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                              (TLS HelloRetryRequest)
                                 <--------
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                                    (TLS ServerHello,
                                             TLS EncryptedExtensions,
                                                        TLS Finished,
                                 <--------          TLS empty record)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS Finished)                -------->
                                 <--------               EAP-Success

                Figure 6: EAP-TLS with Hello Retry Request

2.1.5.  Ticket Establishment

   When using EAP-TLS with TLS 1.3, the EAP server MUST indicate support
   of resumption in the initial authentication.  To indicate support of
   resumption, the EAP server sends a NewSessionTicket message
   (containing a PSK and other parameters) after it has received the
   Finished message.  The NewSessionTicket message MUST NOT include an
   "early_data" extension.

   In the case where EAP-TLS with mutual authentication and ticket
   establishment is successful, the conversation will appear as shown in
   Figure 7.

Mattsson & Sethi        Expires November 27, 2019              [Page 10]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                                    (TLS ServerHello,
                                             TLS EncryptedExtensions,
                                              TLS CertificateRequest,
                                                     TLS Certificate,
                                               TLS CertificateVerify,
                                 <--------              TLS Finished)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS Certificate,
    TLS CertificateVerify,
    TLS Finished)                -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                               (TLS NewSessionTicket,
                                 <--------          TLS empty record)
    EAP-Response/
    EAP-Type=EAP-TLS             -------->
                                 <--------               EAP-Success

                  Figure 7: EAP-TLS ticket establishment

2.1.6.  Resumption

   TLS 1.3 replaces the session resumption mechanisms in earlier
   versions of TLS with a new PSK exchange.  When EAP-TLS is used with
   TLS version 1.3 or higher, EAP-TLS SHALL use a resumption mechanism
   compatible with that version of TLS.

   For TLS 1.3, resumption is described in Section 2.2 of [RFC8446].  If
   the client has received a NewSessionTicket message from the server,
   the client can use the PSK identity received in the ticket to
   negotiate the use of the associated PSK.  If the server accepts it,
   then the security context of the new connection is tied to the
   original connection and the key derived from the initial handshake is

Mattsson & Sethi        Expires November 27, 2019              [Page 11]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   used to bootstrap the cryptographic state instead of a full
   handshake.  It is left up to the EAP peer whether to use resumption,
   but it is RECOMMENDED that the EAP server accept resumption as long
   as the ticket is valid.  However, the server MAY choose to require a
   full authentication.

   A subsequent authentication using resumption, where both sides
   authenticate successfully is shown in Figure 8.

    EAP Peer                                              EAP Server

                                                         EAP-Request/
                                 <--------                  Identity
    EAP-Response/
    Identity (Privacy-Friendly)  -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                 <--------                (TLS Start)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS ClientHello)             -------->
                                                         EAP-Request/
                                                    EAP-Type=EAP-TLS
                                                    (TLS ServerHello,
                                             TLS EncryptedExtensions,
                                                        TLS Finished,
                                 <--------          TLS empty record)
    EAP-Response/
    EAP-Type=EAP-TLS
   (TLS Finished)                -------->
                                 <--------               EAP-Success

                       Figure 8: EAP-TLS resumption

   As specified in Section 2.2 of [RFC8446], the EAP peer SHOULD supply
   a "key_share" extension when offering resumption, which allows the
   EAP server to decline resumption and continue the handshake as a full
   handshake.  The message flow in case of mutual authentication is
   given by Figure 1.  If the EAP peer did not supply a "key_share"
   extension when offering resumption, the EAP server needs to reject
   the ClientHello and the EAP peer needs to restart a full handshake.
   The message flow in this case is given by Figure 2 followed by
   Figure 1.

   Also during resumption, the server can respond with a Hello Retry
   Request (see Section 2.1.4) and issue a new ticket (see
   Section 2.1.5)

Mattsson & Sethi        Expires November 27, 2019              [Page 12]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

2.1.7.  Privacy

   TLS 1.3 significantly improves privacy when compared to earlier
   versions of TLS by forbidding cipher suites without confidentiality
   and encrypting large parts of the TLS handshake including the
   certificate messages.

   EAP-TLS peer and server implementations supporting TLS 1.3 or higher
   MUST support anonymous NAIs (Network Access Identifiers) (Section 2.4
   in [RFC7542]) and a client supporting TLS 1.3 MUST NOT send its
   username in cleartext in the Identity Response.  It is RECOMMENDED to
   use anonymous NAIs, but other privacy-friendly identities (e.g.
   encrypted usernames) MAY be used.

   As the certificate messages in TLS 1.3 are encrypted, there is no
   need to send an empty certificate_list and perform a second handshake
   for privacy (as needed by EAP-TLS with earlier versions of TLS).
   When EAP-TLS is used with TLS version 1.3 or higher the EAP-TLS peer
   and EAP-TLS server SHALL follow the processing specified by the used
   version of TLS.  For TLS 1.3 this means that the EAP-TLS peer only
   sends an empty certificate_list if it does not have an appropriate
   certificate to send, and the EAP-TLS server MAY treat an empty
   certificate_list as a terminal condition.

   EAP-TLS with TLS 1.3 is always used with privacy.  This does not add
   any extra round-trips and the message flow with privacy is just the
   normal message flow as shown in Figure 1.

2.1.8.  Fragmentation

   Including ContentType and ProtocolVersion a single TLS record may be
   up to 16387 octets in length.  EAP-TLS fragmentation support is
   provided through addition of a flags octet within the EAP-Response
   and EAP-Request packets, as well as a TLS Message Length field of
   four octets.  Implementations MUST NOT set the L bit in unfragmented
   messages, but MUST accept unfragmented messages with and without the
   L bit set.

   Some EAP implementations and access networks may limit the number of
   EAP packet exchanges that can be handled.  To avoid fragmentation, it
   is RECOMMENDED to keep the sizes of client, server, and trust anchor
   certificates small and the length of the certificate chains short.
   In addition, it is RECOMMENDED to use mechanisms that reduce the
   sizes of Certificate messages.

   While Elliptic Curve Cryptography (ECC) was optional for earlier
   version of TLS, TLS 1.3 mandates support of ECC (see Section 9 of
   [RFC8446]).  To avoid fragmentation, the use of ECC in certificates,

Mattsson & Sethi        Expires November 27, 2019              [Page 13]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   signature algorithms, and groups are RECOMMENDED when using EAP-TLS
   with TLS 1.3 or higher.  At a 128-bit security level, this reduces
   public key sizes from 384 bytes (RSA and DHE) to 32-64 bytes (ECDHE)
   and signatures from 384 bytes (RSA) to 64 bytes (ECDSA and EdDSA).
   An EAP-TLS deployment MAY further reduce the certificate sizes by
   limiting the number of Subject Alternative Names.

   Endpoints SHOULD reduce the sizes of Certificate messages by omitting
   certificates that the other endpoint is known to possess.  When using
   TLS 1.3, all certificates that specifies a trust anchor may be
   omitted (see Section 4.4.2 of [RFC8446]).  When using TLS 1.2, only
   the self-signed certificate that specifies the root certificate
   authority may be omitted (see Section 7.4.2 of [RFC5246]).  EAP-TLS
   peers and servers SHOULD support and use the Cached Information
   Extension as specified in [RFC7924].  EAP-TLS peers and servers MAY
   use other extensions for reducing the sizes of Certificate messages,
   e.g. certificate compression [I-D.ietf-tls-certificate-compression].

2.2.  Identity Verification

   The identity provided in the EAP-Response/Identity is not
   authenticated by EAP-TLS.  Unauthenticated information SHALL NOT be
   used for accounting purposes or to give authorization.  The
   authenticator and the EAP server MAY examine the identity presented
   in EAP-Response/Identity for purposes such as routing and EAP method
   selection.  They MAY reject conversations if the identity does not
   match their policy.  Note that this also applies to resumption, see
   Sections 2.1.6, 5.6, and 5.7.

2.3.  Key Hierarchy

   TLS 1.3 replaces the TLS pseudorandom function (PRF) used in earlier
   versions of TLS with HKDF and completely changes the Key Schedule.
   The key hierarchies shown in Section 2.3 of [RFC5216] are therefore
   not correct when EAP-TLS is used with TLS version 1.3 or higher.  For
   TLS 1.3 the key schedule is described in Section 7.1 of [RFC8446].

   When EAP-TLS is used with TLS version 1.3 or higher the Key_Material,
   IV, and Method-Id SHALL be derived from the exporter_master_secret
   using the TLS exporter interface [RFC5705] (for TLS 1.3 this is
   defined in Section 7.5 of [RFC8446]).

Mattsson & Sethi        Expires November 27, 2019              [Page 14]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   Type-Code    = 0x0D
   Key_Material = TLS-Exporter("EXPORTER_EAP_TLS_Key_Material",
                               Type-Code, 128)
   IV           = TLS-Exporter("EXPORTER_EAP_TLS_IV",
                               Type-Code, 64)
   Method-Id    = TLS-Exporter("EXPORTER_EAP_TLS_Method-Id",
                               Type-Code, 64)
   Session-Id   = Type-Code || Method-Id

   All other parameters such as MSK and EMSK are derived in the same
   manner as with EAP-TLS [RFC5216], Section 2.3.  The definitions are
   repeated below for simplicity:

   MSK          = Key_Material(0, 63)
   EMSK         = Key_Material(64, 127)
   Enc-RECV-Key = MSK(0, 31)
   Enc-SEND-Key = MSK(32, 63)
   RECV-IV      = IV(0, 31)
   SEND-IV      = IV(32, 63)

   The use of these keys is specific to the lower layer, as described
   [RFC5247].

   Note that the key derivation MUST use the length values given above.
   While in TLS 1.2 and earlier it was possible to truncate the output
   by requesting less data from the TLS-Exporter function, this practice
   is not possible with TLS 1.3.  If an implementation intends to use
   only a part of the output of the TLS-Exporter function, then it MUST
   ask for the full output and then only use the desired part.  Failure
   to do so will result in incorrect values being calculated for the
   above keying material.

   By using the TLS exporter, EAP-TLS can use any TLS 1.3 implementation
   without having to extract the Master Secret, ClientHello.random, and
   ServerHello.random in a non-standard way.

2.4.  Parameter Negotiation and Compliance Requirements

   TLS 1.3 cipher suites are defined differently than in earlier
   versions of TLS (see Section B.4 of [RFC8446]), and the cipher suites
   discussed in Section 2.4 of [RFC5216] can therefore not be used when
   EAP-TLS is used with TLS version 1.3 or higher.

   When EAP-TLS is used with TLS version 1.3 or higher, the EAP-TLS
   peers and servers MUST comply with the compliance requirements
   (mandatory-to-implement cipher suites, signature algorithms, key
   exchange algorithms, extensions, etc.) for the TLS version used.  For

Mattsson & Sethi        Expires November 27, 2019              [Page 15]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   TLS 1.3 the compliance requirements are defined in Section 9 of
   [RFC8446].

   While EAP-TLS does not protect any application data, the negotiated
   cipher suites and algorithms MAY be used to secure data as done in
   other TLS-based EAP methods.

2.5.  EAP State Machines

   TLS 1.3 [RFC8446] introduces Post-Handshake messages.  These Post-
   Handshake messages use the handshake content type and can be sent
   after the main handshake.  One such Post-Handshake message is
   NewSessionTicket.  The NewSessionTicket can be used for resumption.
   After sending TLS Finished, the EAP server may send any number of
   Post-Handshake messages in separate EAP-Requests.  To decrease the
   uncertainty for the EAP peer, the following procedure MUST be
   followed:

   When an EAP server has sent its last handshake message (Finished or a
   Post-Handshake), it commits to not sending any more handshake
   messages by appending an empty application data record (i.e. a TLS
   record with TLSPlaintext.type = application_data and
   TLSPlaintext.length = 0) to the last handshake record.  After sending
   an empty application data record, the EAP server may only send an
   EAP-Success, an EAP-Failure, or an EAP-Request with a TLS Alert
   Message.

3.  Detailed Description of the EAP-TLS Protocol

   No updates to [RFC5216].

4.  IANA considerations

   This section provides guidance to the Internet Assigned Numbers
   Authority (IANA) regarding registration of values related to the EAP-
   TLS 1.3 protocol in accordance with [RFC8126].

   This memo requires IANA to add the following labels to the TLS
   Exporter Label Registry defined by [RFC5705].  These labels are used
   in derivation of Key_Material, IV and Method-Id as defined in
   Section 2.3:

   o  "EXPORTER_EAP_TLS_Key_Material"

   o  "EXPORTER_EAP_TLS_IV"

   o  "EXPORTER_EAP_TLS_Method-Id"

Mattsson & Sethi        Expires November 27, 2019              [Page 16]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

5.  Security Considerations

5.1.  Security Claims

   Using EAP-TLS with TLS 1.3 does not change the security claims for
   EAP-TLS as given in Section 4.1 of [RFC5216].  However, it
   strengthens several of the claims as described in the following
   updates to the notes given in Section 4.1 of [RFC5216].

   [1] Mutual authentication: By mandating revocation checking of
   certificates, the authentication in EAP-TLS with TLS 1.3 is stronger
   as authentication with revoked certificates will always fail.

   [2] Confidentiality: The TLS 1.3 handshake offers much better
   confidentiality than earlier versions of TLS by mandating cipher
   suites with confidentiality and encrypting certificates and some of
   the extensions, see [RFC8446].  When using EAP-TLS with TLS 1.3, the
   use of privacy is mandatory and does not cause any additional round-
   trips.

   [3] Key strength: TLS 1.3 forbids all algorithms with known
   weaknesses including 3DES, CBC mode, RC4, SHA-1, and MD5.  TLS 1.3
   only supports cryptographic algorithms offering at least 112-bit
   security, see [RFC8446].

   [4] Cryptographic Negotiation: TLS 1.3 increases the number of
   cryptographic parameters that are negotiated in the handshake.  When
   EAP-TLS is used with TLS 1.3, EAP-TLS inherits the cryptographic
   negotiation of AEAD algorithm, HKDF hash algorithm, key exchange
   groups, and signature algorithm, see Section 4.1.1 of [RFC8446].

5.2.  Peer and Server Identities

   No updates to [RFC5216].

5.3.  Certificate Validation

   No updates to [RFC5216].

5.4.  Certificate Revocation

   While certificates often have a long validity period spanning several
   years, there are a number of reasons (e.g. key compromise, CA
   compromise, privilege withdrawn, etc.) why client, server, or sub-CA
   certificates have to be revoked before their expiry date.  Revocation
   of the EAP server's certificate is complicated by the fact that the
   EAP peer may not have Internet connectivity until authentication
   completes.

Mattsson & Sethi        Expires November 27, 2019              [Page 17]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   EAP-TLS peers and servers supporting TLS 1.3 MUST support Certificate
   Status Requests (OCSP stapling) as specified in [RFC6066] and
   Section 4.4.2.1 of [RFC8446].  When EAP-TLS is used with TLS 1.3, the
   peer and server MUST use Certificate Status Requests [RFC6066] for
   the server's certificate chain and the EAP peer MUST treat a
   CertificateEntry (except the trust anchor) without a valid
   CertificateStatus extension as invalid and abort the handshake with
   an appropriate alert.  When EAP-TLS is used with TLS 1.3, the server
   MUST check the revocation status of the certificates in the
   certificates in the client's certificate chain.

   The OCSP status handling in TLS 1.3 is different from earlier
   versions of TLS, see Section 4.4.2.1 of [RFC8446].  In TLS 1.3 the
   OCSP information is carried in the CertificateEntry containing the
   associated certificate instead of a separate CertificateStatus
   message as in [RFC4366].  This enables sending OCSP information for
   all certificates in the certificate chain.

5.5.  Packet Modification Attacks

   No updates to [RFC5216].

5.6.  Authorization

   EAP-TLS is typically encapsulated in other protocols, such as PPP
   [RFC1661], RADIUS [RFC2865], Diameter [RFC6733], or PANA [RFC5191].
   The encapsulating protocols can also provide additional, non-EAP
   information to an EAP server.  This information can include, but is
   not limited to, information about the authenticator, information
   about the EAP peer, or information about the protocol layers above or
   below EAP (MAC addresses, IP addresses, port numbers, WiFi SSID,
   etc.).  Servers implementing EAP-TLS inside those protocols can make
   policy decisions and enforce authorization based on a combination of
   information from the EAP-TLS exchange and non-EAP information.

   As noted in Section 2.2, the identity presented in EAP-Response/
   Identity is not authenticated by EAP-TLS and is therefore trivial for
   an attacker to forge, modify, or replay.  Authorization and
   accounting MUST be based on authenticated information such as
   information in the certificate or the PSK identity and cached data
   provisioned for resumption as described in Section 5.7.  Note that
   the requirements for Network Access Identifiers (NAIs) specified in
   Section 4 of [RFC7542] still apply and MUST be followed.

   EAP-TLS servers MAY reject conversations based on non-EAP information
   provided by the encapsulating protocol, for example, if the MAC
   address of the authenticator does not match the expected policy.

Mattsson & Sethi        Expires November 27, 2019              [Page 18]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

5.7.  Resumption

   There are a number of security issues related to resumption that are
   not described in [RFC5216].  The problems, guidelines, and
   requirements in this section therefore applies to all version of TLS.

   When resumption occurs, it is based on cached information at the TLS
   layer.  To perform resumption in a secure way, the EAP-TLS peer and
   EAP-TLS server need to be able to securely retrieve authorization
   information such as certificate chains, revocation status, etc. from
   the initial full handshake.  We use the term "cached data" to
   describe such information.  Authorization during resumption MUST be
   based on such cached data.

   There are two ways to retrieve the cached information from the
   original full handshake.  The first method is that the TLS server and
   client cache the information locally.  The cached information is
   identified by an identifier.  For TLS versions before 1.3, the
   identifier can be the session ID, for TLS 1.3, the identifier is the
   PSK identity.  The second method for retrieving cached information is
   via [RFC5077] or [RFC8446], where the TLS server encapsulates the
   information into a ticket and sends it to the client.  The client can
   subsequently do resumption using the obtained ticket.  Note that the
   client still needs to cache the information locally.  The following
   requirements apply to both methods.

   If the EAP server or EAP client do not apply any authorization
   policies, they MAY allow resumption where no cached data is
   available.  In all other cases, they MUST cache data during the
   initial full authentication to enable resumption.  The cached data
   MUST be sufficient to make authorization decisions during resumption.
   If cached data cannot be retrieved in a secure way, resumption MUST
   NOT be done.

   The above requirements also apply if the EAP server expects some
   system to perform accounting for the session.  Since accounting must
   be tied to an authenticated identity, and resumption does not supply
   such an identity, accounting is impossible without access to cached
   data.

   Information from the EAP-TLS exchange (e.g. the identity provided in
   EAP-Response/Identity) as well as non-EAP information (e.g.  IP
   addresses) may change between the initial full handshake and
   resumption.  This change creates a "Time-of-check time-of-use"
   (TOCTOU) security vulnerability.  A malicious or compromised user
   could supply one set of data during the initial authentication, and a
   different set of data during resumption, potentially leading to them
   obtaining access that they should not have.

Mattsson & Sethi        Expires November 27, 2019              [Page 19]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   If any authorization, accounting, or policy decisions were made with
   information that have changed between the initial full handshake and
   resumption, and if change may lead to a different decision, such
   decisions MUST be reevaluated.  It is RECOMMENDED that authorization,
   accounting, and policy decisions are reevaluated based on the
   information given in the resumption.  EAP servers MAY reject
   resumption where the information supplied during resumption does not
   match the information supplied during the original authentication.
   Where a good decision is unclear, EAP servers SHOULD reject the
   resumption.

   Any security policies for authorization MUST be followed also for
   resumption.  The EAP-TLS client and server MAY need to recheck the
   authorization and revocation status of the other party.  The
   certificates may have been revoked since the initial full handshake
   and the authorizations of the other party may have been reduced.  If
   the cached revocation information is not sufficiently current, the
   EAP Peer or EAP Server needs to force a full TLS handshake.

5.8.  Privacy Considerations

   [RFC6973] suggests that the privacy considerations of IETF protocols
   be documented.

   TLS 1.3 offers much better privacy than earlier versions of TLS as
   discussed in Section 2.1.7.  In this section, we only discuss the
   privacy properties of EAP-TLS with TLS 1.3.  For privacy properties
   of TLS 1.3 itself, see [RFC8446].

   EAP-TLS sends the standard TLS 1.3 handshake messages encapsulated in
   EAP packets.  Additionally, the EAP peer sends an identity in the
   first EAP-Response.  The other fields in the EAP-TLS Request and the
   EAP-TLS Response packets do not contain any cleartext privacy
   sensitive information.

   Tracking of users by eavesdropping on identity responses or
   certificates is a well-known problem in many EAP methods.  When EAP-
   TLS is used with TLS 1.3, all certificates are encrypted, and the
   username part of the identity response is always confidentiality
   protected (e.g. using Anonymous NAIs).  However, as with other EAP
   methods, even when privacy-friendly identifiers or EAP tunneling is
   used, the domain name (i.e. the realm) in the NAI is still typically
   visible.  How much privacy sensitive information the domain name
   leaks is highly dependent on how many other users are using the same
   domain name in the particular access network.  If all EAP peers have
   the same domain, no additional information is leaked.  If a domain
   name is used by a small subset of the EAP peers, it may aid an
   attacker in tracking or identifying the user.

Mattsson & Sethi        Expires November 27, 2019              [Page 20]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   If Anonymous NAIs are not used, the privacy-friendly identifiers need
   to be generated with care.  The identities MUST be generated in a
   cryptographically secure way so that that it is computationally
   infeasible for an attacker to differentiate two identities belonging
   to the same user from two identities belonging to different users in
   the same realm.  This can be achieved, for instance, by using random
   or pseudo-random usernames such as random byte strings or
   ciphertexts.  Note that the privacy-friendly usernames also MUST NOT
   include substrings that can be used to relate the identity to a
   specific user.  Similarly, privacy-friendly username SHOULD NOT be
   formed by a fixed mapping that stays the same across multiple
   different authentications.

   An EAP peer with a policy allowing communication with EAP servers
   supporting only TLS 1.2 without privacy and with a static RSA key
   exchange is vulnerable to disclosure of the peer username.  An active
   attacker can in this case make the EAP peer believe that an EAP
   server supporting TLS 1.3 only supports TLS 1.2 without privacy.  The
   attacker can simply impersonate the EAP server and negotiate TLS 1.2
   with static RSA key exchange and send an TLS alert message when the
   EAP peer tries to use privacy by sending an empty certificate
   message.  Since the attacker (impersonating the EAP server) does not
   provide a proof-of-possession of the private key until the Finished
   message when a static RSA key exchange is used, an EAP peer may
   inadvertently disclose its identity (username) to an attacker.
   Therefore, it is RECOMMENDED for EAP peers to not use EAP-TLS with
   TLS 1.2 and static RSA based cipher suites without privacy.

5.9.  Pervasive Monitoring

   As required by [RFC7258], work on IETF protocols needs to consider
   the effects of pervasive monitoring and mitigate them when possible.

   Pervasive Monitoring is widespread surveillance of users.  By
   encrypting more information and by mandating the use of privacy, TLS
   1.3 offers much better protection against pervasive monitoring.  In
   addition to the privacy attacks discussed above, surveillance on a
   large scale may enable tracking of a user over a wider geographical
   area and across different access networks.  Using information from
   EAP-TLS together with information gathered from other protocols
   increases the risk of identifying individual users.

5.10.  Discovered Vulnerabilities

   Over the years, there have been several serious attacks on earlier
   versions of Transport Layer Security (TLS), including attacks on its
   most commonly used ciphers and modes of operation.  [RFC7457]
   summarizes the attacks that were known at the time of publishing and

Mattsson & Sethi        Expires November 27, 2019              [Page 21]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   [RFC7525] provides recommendations for improving the security of
   deployed services that use TLS.  However, many of the attacks are
   less serious for EAP-TLS as EAP-TLS only uses the TLS handshake and
   does not protect any application data.  EAP-TLS implementations
   SHOULD mitigate known attacks and follow the recommendations in
   [RFC7525] and [I-D.ietf-tls-oldversions-deprecate].  The use of TLS
   1.3 mitigates most of the known attacks.

6.  References

6.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC3748]  Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J., and H.
              Levkowetz, Ed., "Extensible Authentication Protocol
              (EAP)", RFC 3748, DOI 10.17487/RFC3748, June 2004,
              <https://www.rfc-editor.org/info/rfc3748>.

   [RFC5216]  Simon, D., Aboba, B., and R. Hurst, "The EAP-TLS
              Authentication Protocol", RFC 5216, DOI 10.17487/RFC5216,
              March 2008, <https://www.rfc-editor.org/info/rfc5216>.

   [RFC5280]  Cooper, D., Santesson, S., Farrell, S., Boeyen, S.,
              Housley, R., and W. Polk, "Internet X.509 Public Key
              Infrastructure Certificate and Certificate Revocation List
              (CRL) Profile", RFC 5280, DOI 10.17487/RFC5280, May 2008,
              <https://www.rfc-editor.org/info/rfc5280>.

   [RFC5705]  Rescorla, E., "Keying Material Exporters for Transport
              Layer Security (TLS)", RFC 5705, DOI 10.17487/RFC5705,
              March 2010, <https://www.rfc-editor.org/info/rfc5705>.

   [RFC6066]  Eastlake 3rd, D., "Transport Layer Security (TLS)
              Extensions: Extension Definitions", RFC 6066,
              DOI 10.17487/RFC6066, January 2011,
              <https://www.rfc-editor.org/info/rfc6066>.

   [RFC6960]  Santesson, S., Myers, M., Ankney, R., Malpani, A.,
              Galperin, S., and C. Adams, "X.509 Internet Public Key
              Infrastructure Online Certificate Status Protocol - OCSP",
              RFC 6960, DOI 10.17487/RFC6960, June 2013,
              <https://www.rfc-editor.org/info/rfc6960>.

Mattsson & Sethi        Expires November 27, 2019              [Page 22]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   [RFC7542]  DeKok, A., "The Network Access Identifier", RFC 7542,
              DOI 10.17487/RFC7542, May 2015,
              <https://www.rfc-editor.org/info/rfc7542>.

   [RFC7924]  Santesson, S. and H. Tschofenig, "Transport Layer Security
              (TLS) Cached Information Extension", RFC 7924,
              DOI 10.17487/RFC7924, July 2016,
              <https://www.rfc-editor.org/info/rfc7924>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
              <https://www.rfc-editor.org/info/rfc8446>.

6.2.  Informative references

   [I-D.ietf-tls-certificate-compression]
              Ghedini, A. and V. Vasiliev, "TLS Certificate
              Compression", draft-ietf-tls-certificate-compression-05
              (work in progress), April 2019.

   [I-D.ietf-tls-oldversions-deprecate]
              Moriarty, K. and S. Farrell, "Deprecating TLSv1.0 and
              TLSv1.1", draft-ietf-tls-oldversions-deprecate-04 (work in
              progress), May 2019.

   [IEEE-802.11]
              Institute of Electrical and Electronics Engineers, "IEEE
              Standard for Information technology--Telecommunications
              and information exchange between systems Local and
              metropolitan area networks--Specific requirements - Part
              11: Wireless LAN Medium Access Control (MAC) and Physical
              Layer (PHY) Specifications", IEEE Std 802.11-2016
              (Revision of IEEE Std 802.11-2012) , December 2016.

   [IEEE-802.1X]
              Institute of Electrical and Electronics Engineers, "IEEE
              Standard for Local and metropolitan area networks -- Port-
              Based Network Access Control", IEEE Standard 802.1X-2010 ,
              February 2010.

Mattsson & Sethi        Expires November 27, 2019              [Page 23]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   [MulteFire]
              MulteFire, "MulteFire Release 1.0.1 specification", 2017.

   [RFC1661]  Simpson, W., Ed., "The Point-to-Point Protocol (PPP)",
              STD 51, RFC 1661, DOI 10.17487/RFC1661, July 1994,
              <https://www.rfc-editor.org/info/rfc1661>.

   [RFC2246]  Dierks, T. and C. Allen, "The TLS Protocol Version 1.0",
              RFC 2246, DOI 10.17487/RFC2246, January 1999,
              <https://www.rfc-editor.org/info/rfc2246>.

   [RFC2560]  Myers, M., Ankney, R., Malpani, A., Galperin, S., and C.
              Adams, "X.509 Internet Public Key Infrastructure Online
              Certificate Status Protocol - OCSP", RFC 2560,
              DOI 10.17487/RFC2560, June 1999,
              <https://www.rfc-editor.org/info/rfc2560>.

   [RFC2865]  Rigney, C., Willens, S., Rubens, A., and W. Simpson,
              "Remote Authentication Dial In User Service (RADIUS)",
              RFC 2865, DOI 10.17487/RFC2865, June 2000,
              <https://www.rfc-editor.org/info/rfc2865>.

   [RFC3280]  Housley, R., Polk, W., Ford, W., and D. Solo, "Internet
              X.509 Public Key Infrastructure Certificate and
              Certificate Revocation List (CRL) Profile", RFC 3280,
              DOI 10.17487/RFC3280, April 2002,
              <https://www.rfc-editor.org/info/rfc3280>.

   [RFC4282]  Aboba, B., Beadles, M., Arkko, J., and P. Eronen, "The
              Network Access Identifier", RFC 4282,
              DOI 10.17487/RFC4282, December 2005,
              <https://www.rfc-editor.org/info/rfc4282>.

   [RFC4346]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.1", RFC 4346,
              DOI 10.17487/RFC4346, April 2006,
              <https://www.rfc-editor.org/info/rfc4346>.

   [RFC4366]  Blake-Wilson, S., Nystrom, M., Hopwood, D., Mikkelsen, J.,
              and T. Wright, "Transport Layer Security (TLS)
              Extensions", RFC 4366, DOI 10.17487/RFC4366, April 2006,
              <https://www.rfc-editor.org/info/rfc4366>.

   [RFC5077]  Salowey, J., Zhou, H., Eronen, P., and H. Tschofenig,
              "Transport Layer Security (TLS) Session Resumption without
              Server-Side State", RFC 5077, DOI 10.17487/RFC5077,
              January 2008, <https://www.rfc-editor.org/info/rfc5077>.

Mattsson & Sethi        Expires November 27, 2019              [Page 24]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   [RFC5191]  Forsberg, D., Ohba, Y., Ed., Patil, B., Tschofenig, H.,
              and A. Yegin, "Protocol for Carrying Authentication for
              Network Access (PANA)", RFC 5191, DOI 10.17487/RFC5191,
              May 2008, <https://www.rfc-editor.org/info/rfc5191>.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246,
              DOI 10.17487/RFC5246, August 2008,
              <https://www.rfc-editor.org/info/rfc5246>.

   [RFC5247]  Aboba, B., Simon, D., and P. Eronen, "Extensible
              Authentication Protocol (EAP) Key Management Framework",
              RFC 5247, DOI 10.17487/RFC5247, August 2008,
              <https://www.rfc-editor.org/info/rfc5247>.

   [RFC6733]  Fajardo, V., Ed., Arkko, J., Loughney, J., and G. Zorn,
              Ed., "Diameter Base Protocol", RFC 6733,
              DOI 10.17487/RFC6733, October 2012,
              <https://www.rfc-editor.org/info/rfc6733>.

   [RFC6973]  Cooper, A., Tschofenig, H., Aboba, B., Peterson, J.,
              Morris, J., Hansen, M., and R. Smith, "Privacy
              Considerations for Internet Protocols", RFC 6973,
              DOI 10.17487/RFC6973, July 2013,
              <https://www.rfc-editor.org/info/rfc6973>.

   [RFC7258]  Farrell, S. and H. Tschofenig, "Pervasive Monitoring Is an
              Attack", BCP 188, RFC 7258, DOI 10.17487/RFC7258, May
              2014, <https://www.rfc-editor.org/info/rfc7258>.

   [RFC7406]  Schulzrinne, H., McCann, S., Bajko, G., Tschofenig, H.,
              and D. Kroeselberg, "Extensions to the Emergency Services
              Architecture for Dealing With Unauthenticated and
              Unauthorized Devices", RFC 7406, DOI 10.17487/RFC7406,
              December 2014, <https://www.rfc-editor.org/info/rfc7406>.

   [RFC7457]  Sheffer, Y., Holz, R., and P. Saint-Andre, "Summarizing
              Known Attacks on Transport Layer Security (TLS) and
              Datagram TLS (DTLS)", RFC 7457, DOI 10.17487/RFC7457,
              February 2015, <https://www.rfc-editor.org/info/rfc7457>.

   [RFC7525]  Sheffer, Y., Holz, R., and P. Saint-Andre,
              "Recommendations for Secure Use of Transport Layer
              Security (TLS) and Datagram Transport Layer Security
              (DTLS)", BCP 195, RFC 7525, DOI 10.17487/RFC7525, May
              2015, <https://www.rfc-editor.org/info/rfc7525>.

Mattsson & Sethi        Expires November 27, 2019              [Page 25]
Internet-Draft            EAP-TLS with TLS 1.3                  May 2019

   [TS.33.501]
              3GPP, "Security architecture and procedures for 5G
              System", 3GPP TS 33.501 15.4.0, March 2019.

Appendix A.  Updated references

   All the following references in [RFC5216] are updated as specified
   below when EAP-TLS is used with TLS 1.3 or higher.

   All references to [RFC2560] are updated with [RFC6960].

   All references to [RFC3280] are updated with [RFC5280].

   All references to [RFC4282] are updated with [RFC7542].

Acknowledgments

   The authors want to thank Bernard Aboba, Jari Arkko, Alan DeKok, Ari
   Keraenen, Jouni Malinen, Oleg Pekar, Eric Rescorla, Jim Schaad, and
   Vesa Torvinen for comments and suggestions on the draft.

Contributors

   Alan DeKok, FreeRADIUS

Authors' Addresses

   John Mattsson
   Ericsson
   Stockholm  164 40
   Sweden

   Email: john.mattsson@ericsson.com

   Mohit Sethi
   Ericsson
   Jorvas  02420
   Finland

   Email: mohit@piuha.net

Mattsson & Sethi        Expires November 27, 2019              [Page 26]