Additional Data related to an Emergency Call
draft-ietf-ecrit-additional-data-08
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft that was ultimately published as RFC 7852.
|
|
|---|---|---|---|
| Authors | Brian Rosen , Hannes Tschofenig , Roger Marshall , Randall Gellens | ||
| Last updated | 2013-05-05 | ||
| Replaces | draft-rosen-ecrit-additional-data | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Formats | |||
| Reviews |
GENART Telechat review
(of
-34)
by Francis Dupont
Almost ready
GENART Last Call review
(of
-33)
by Francis Dupont
Almost ready
|
||
| Additional resources | Mailing list discussion | ||
| Stream | WG state | WG Document | |
| Document shepherd | (None) | ||
| IESG | IESG state | Became RFC 7852 (Proposed Standard) | |
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-ietf-ecrit-additional-data-08
ECRIT B.R. Rosen
Internet-Draft NeuStar
Intended status: Standards Track H. Tschofenig
Expires: November 06, 2013 Nokia Siemens Networks
R. Marshall
TeleCommunication Systems, Inc.
R. Gellens
Qualcomm Technologies, Inc.
May 05, 2013
Additional Data related to an Emergency Call
draft-ietf-ecrit-additional-data-08.txt
Abstract
When an emergency call is sent to a Public Safety Answering Point
(PSAP), the device that sends it, as well as any application service
provider in the path of the call, or access network provider through
which the call originated may have information about the call or the
caller which the PSAP may be able to use. This document describes
data structures to convey such data to the PSAP. In addition, data
may also be included by reference, via a Uniform Resource Identifier
(URI) pointing to data found at an external resource. Consequently,
this document follows the tradition of prior emergency services
standardization work where data can be conveyed by value within the
call signaling (i.e., in body of the SIP message) and also by
reference.
Status of This Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF). Note that other groups may also distribute
working documents as Internet-Drafts. The list of current Internet-
Drafts is at http://datatracker.ietf.org/drafts/current/.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
This Internet-Draft will expire on November 06, 2013.
Copyright Notice
Rosen, et al. Expires November 06, 2013 [Page 1]
Internet-Draft Additional Call Data May 2013
Copyright (c) 2013 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 6
3. Data Structure Overview . . . . . . . . . . . . . . . . . . . 6
4. Transmitting Blocks of Additional Data . . . . . . . . . . . 7
4.1. Transmitting blocks using Call-Info . . . . . . . . . . . 8
4.2. Transmitting blocks by reference using Provided-By . . . 9
4.3. Transmitting blocks by value using Provided-By . . . . . 9
5. Data Provider Information . . . . . . . . . . . . . . . . . . 10
5.1. Data Provider String . . . . . . . . . . . . . . . . . . 10
5.2. Data Provider ID . . . . . . . . . . . . . . . . . . . . 11
5.3. Data Provider ID Series . . . . . . . . . . . . . . . . . 11
5.4. Type of Data Provider . . . . . . . . . . . . . . . . . . 12
5.5. Data Provider Contact URI . . . . . . . . . . . . . . . . 13
5.6. Data Provider Languages(s) Supported . . . . . . . . . . 13
5.7. xCard of Data Provider . . . . . . . . . . . . . . . . . 14
5.8. Subcontractor Principal . . . . . . . . . . . . . . . . . 15
5.9. Subcontractor Priority . . . . . . . . . . . . . . . . . 15
5.10. emergencyCall.ProviderInfo XML Schema . . . . . . . . . . 16
5.11. emergencyCall.ProviderInfo Example . . . . . . . . . . . 17
6. Service Information . . . . . . . . . . . . . . . . . . . . . 19
6.1. Service Environment . . . . . . . . . . . . . . . . . . . 19
6.2. Service Delivered by Provider to End User . . . . . . . . 20
6.3. Service Mobility Environment . . . . . . . . . . . . . . 21
6.4. emergencyCall.SvcInfo XML Schema . . . . . . . . . . . . 22
6.5. emergencyCall.SvcInfo Example . . . . . . . . . . . . . . 22
7. Device Information . . . . . . . . . . . . . . . . . . . . . 23
7.1. Device Classification . . . . . . . . . . . . . . . . . . 23
7.2. Device Manufacturer . . . . . . . . . . . . . . . . . . . 25
7.3. Device Model Number . . . . . . . . . . . . . . . . . . . 25
7.4. Unique Device Identifier . . . . . . . . . . . . . . . . 26
7.5. Type of Device Identifier . . . . . . . . . . . . . . . . 26
7.6. Device/Service Specific Additional Data Structure . . . . 27
7.7. Device/Service Specific Additional Data Structure Type . 28
Rosen, et al. Expires November 06, 2013 [Page 2]
Internet-Draft Additional Call Data May 2013
7.8. Choosing between defining a new type of block or new type
of device/service specific additional data . . . . . . . 28
7.9. emergencyCall.DevInfo XML Schema . . . . . . . . . . . . 29
7.10. emergencyCall.DevInfo Example . . . . . . . . . . . . . . 30
8. Owner/Subscriber Information . . . . . . . . . . . . . . . . 30
8.1. xCard for Subscriber's Data . . . . . . . . . . . . . . . 30
8.2. emergencyCall.SubInfo XML Schema . . . . . . . . . . . . 31
8.3. emergencyCall.SubInfo Example . . . . . . . . . . . . . . 32
9. Comment . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.1. Comment . . . . . . . . . . . . . . . . . . . . . . . . . 34
9.2. emergencyCall.Comment XML Schema . . . . . . . . . . . . 34
9.3. emergencyCall.Comment Example . . . . . . . . . . . . . . 35
10. Example . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11. Main Telephone Number . . . . . . . . . . . . . . . . . . . . 36
12. Security Considerations . . . . . . . . . . . . . . . . . . . 37
13. Privacy Considerations . . . . . . . . . . . . . . . . . . . 38
14. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 38
14.1. Registry creation . . . . . . . . . . . . . . . . . . . 38
14.1.1. Additional Call Data Provider ID Series Registry . . 38
14.1.2. Additional Call Data Service Provider Type Registry 39
14.1.3. Additional Call Data Service Delivered Registry . . 40
14.1.4. Additional Call Data Device Classification Registry 41
14.1.5. Additional Call Data Device ID Type Type Registry . 42
14.1.6. Device/Service Specific Additional Data Type
Registry . . . . . . . . . . . . . . . . . . . . . . 42
14.1.7. Additional Call Data Blocks Registry . . . . . . . . 43
14.2. 'emergencyCallData' Purpose Parameter Value . . . . . . 43
14.3. URN Sub-Namespace Registration for provided-by Registry
Entry . . . . . . . . . . . . . . . . . . . . . . . . . 44
14.3.1. Provided-By XML Schema . . . . . . . . . . . . . . . 44
14.4. MIME Registrations . . . . . . . . . . . . . . . . . . . 45
14.4.1. MIME Content-type Registration for
'application/emergencyCall.ProviderInfo+xml' . . . . 45
14.4.2. MIME Content-type Registration for
'application/emergencyCall.SvcInfo+xml' . . . . . . 46
14.4.3. MIME Content-type Registration for
'application/emergencyCall.DevInfo+xml' . . . . . . 47
14.4.4. MIME Content-type Registration for
'application/emergencyCall.SubInfo+xml' . . . . . . 49
14.4.5. MIME Content-type Registration for
'application/emergencyCall.Comment+xml' . . . . . . 50
14.5. URN Sub-Namespace Registration . . . . . . . . . . . . . 51
14.5.1. Registration for
urn:ietf:params:xml:ns:emergencyCallAddlData . . . . 51
14.5.2. Registration for
urn:ietf:params:xml:ns:emergencyCallProviderInfo . . 52
14.5.3. Registration for
urn:ietf:params:xml:ns:emergencyCall.SvcInfo . . . . 52
Rosen, et al. Expires November 06, 2013 [Page 3]
Internet-Draft Additional Call Data May 2013
14.5.4. Registration for
urn:ietf:params:xml:ns:emergencyCall.DevInfo . . . . 53
14.5.5. Registration for
urn:ietf:params:xml:ns:emergencyCall.SubInfo . . . . 54
14.5.6. Registration for
urn:ietf:params:xml:ns:emergencyCall.Comment . . . . 55
14.6. Schema Registrations . . . . . . . . . . . . . . . . . . 55
14.7. VCard Parameter Value Registration . . . . . . . . . . . 56
15. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 56
16. References . . . . . . . . . . . . . . . . . . . . . . . . . 57
16.1. Normative References . . . . . . . . . . . . . . . . . . 57
16.2. Informational References . . . . . . . . . . . . . . . . 57
Appendix A. XML Schema for vCard/xCard . . . . . . . . . . . . . 58
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 80
1. Introduction
When an emergency call is triggered and the Session Initiation
Protocol (SIP) is used a rich set of data is conveyed to the Public
Safety Answering Point (PSAP) already as part of the call setup,
which includes information about the calling party identity, the
multimedia capabilities of the device, the emergency service number,
etc. The device, as well as any service provider in the path may
have even more information that may be useful for a PSAP call taker.
This document extends the basic signaling of an emergency call, as
described in [RFC6443] and [RFC6881], in order to carry additional
data which may be useful to an entity handling the call. This data
is "additional" to the basic information found in the emergency call
signaling used.
Three general categories of such data are defined, namely data about
the call, the location and the caller. In more detail, the three
types of data exchanged are:
Data Associated with a Call: While information is carried in the
call setup procedure itself (as part of the SIP headers as well as
in the body of the SIP message), there is additional data known by
the device making the call, or a service provider in the path of
the call. This information may include the identity and contact
information of the service provider, subscriber identity and
contact information, the type of service the provider offers, what
kind of device is being used, etc. Some data is device or service
dependent data. For example, a car telematics system or service
may have crash information. A medical monitoring device may have
sensor data. While the details of the information may vary by
device or service, there needs to be a common way to send such
data to a PSAP.
Rosen, et al. Expires November 06, 2013 [Page 4]
Internet-Draft Additional Call Data May 2013
Data Associated with a Location: Location data is conveyed in the
Presence Informatoin Data Format Location Object (PIDF-LO) data
structure originally defined in RFC 4119 [RFC4119]. There may be
data that is specific to the location not available in the
location data structure itself, such as floor plans, tenant and
building owner contact data, Heating, Ventilation and Air
Conditioning (HVAC) status, etc.
Data Associated with a Caller: This is personal data about a caller,
such as medical information and emergency contact data.
This document only defines data structures relevant to data
associated with the call. Other forms of additional data may use
this mechanism to carry data, but those blocks are not defined in
this document.
Data structures are defined for such data, and a means of conveying
the data by including a Uniform Resource Identifier (URI) in an
existing SIP header field, the Call-Info header, which is specified
in Section 20.9 of [RFC3261]. For this purpose a new token, namely
'emergencyCallData' is defined to be carried in the "purpose"
parameter. If the "purpose" parameter is set to 'emergencyCallData'
then the Call-Info header contains a HTTPS URL that resolves to a
data structure with information about the call, or is a CID (content
indirection) that allows the data structure to be placed in the body
of the message. The "purpose" parameter also contains an indication
of what kind of data is available at the URI. As such, the
additional data may reside on an external database, or may be
contained within the body of the SIP message.
Section 10 shows a SIP INVITE example containing such a Call-Info
header using the purpose parameter.
Besides a service provider in the path of a call, the access network
provider (which may provide location in the form of a PIDF-LO
[RFC4119] from a location server via a location configuration
protocol) also has similar information that may be valuable to the
PSAP. This information is not specific to the location itsef, but
rather provides descriptive information having to do with the
immediate circumstances about the provision of the location (who the
access network is, how to contact that entity, what kind of service
the access network provides, subscriber information, etc.). This
data is similar in nearly every respect to the data known by service
providers in the path of the call. When the access network provider
and service provider are separate entities, the access network does
not participate in the application layer signaling (and hence cannot
add a Call-Info' header field to the SIP message), but may provide
location information to assist in locating the caller's device. The
Rosen, et al. Expires November 06, 2013 [Page 5]
Internet-Draft Additional Call Data May 2013
'provided-by' element of the PIDF-LO is a mechanism for the access
network to supply the information about the entity or organization
that supplied this location information. For this reason, this
document describes a namespace per [RFC4119] for inclusion in the
"provided-by" element of a PIDF-LO for adding information known to
the access network.
More technically, the data structure described in this document is
represented as one or more "blocks" of information. Each of the
blocks is a Multipurpose Internet Mail Extensions (MIME) type, and an
extensible set of these types constitute the data set. A registry is
defined to list the block types that may be included.
2. Terminology
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
This document also uses terminology from [RFC5012]. We use the term
service provider to refer to an Application Service Provider (ASP) or
to Voice Service Provider (VSP), which is a specific type of ASP.
With the term "Access Network Provider" we refer to the Internet
Access Provider (IAP) and the Internet Service Provider (ISP) without
further distinguishing these two entities, since the difference
between the two is not relevant for this document. Note that the
roles of ASP and access network provider may be provided by a single
company.
In the data block definitions, the "Use:" values are specified as one
of:
'Mandatory': means they must be present in the data structure.
'Conditional': means they must be present unless the specified
condition is met, in which case the they may be present.
'Optional': means they may be present.
3. Data Structure Overview
The following section defines an initial set of blocks which may be
sent by value or by reference in SIP signaling or within a PIDF-LO.
For each block, we define the MIME type, and the XML data structure
for the block. The following blocks are defined:
'Data Provider': This block supplies name and contact information
for the entity that created the data.
Rosen, et al. Expires November 06, 2013 [Page 6]
Internet-Draft Additional Call Data May 2013
'Service Information': This block supplies information about the
service provided by a service provider.
'Device Information': This block supplies information about the
device placing the call.
'Owner/Subscriber': This block supplies information about the owner
of the device or about the subscriber of the application service.
'Comment': This block provides a way to supply free form human
readable text to the PSAP or emergency responders.
PSAPs and emergency responders can examine the type of data provided
and selectively retrieve the data each they are interested in, while
forwarding all of it (the values or references) to downstream
entities.
Blocks can be sent by value (the data in the SIP body or PIDF-LO) or
by reference (the data is retrieved via HTTPS from an external
server). Data may be provided by the device and/or one or more
service providers. For example, the device may provide device
specific information by value, a telematics service provider may
provide its contact data and data derived from the sensor data (e.g.,
injury prediction) by reference, and an access network provider may
provide contact information by value, all in the same SIP INVITE.
The access network provider may supply additional data as well, by
including the data within a Provided-By element of a PDIF-LO it
returns for emergency use (e.g., if requested with a HELD
"responseTime" attribute of "emergencyRouting" or "emergencyDispatch"
[RFC5985]). Access network providers are expected to normally supply
such information by reference (by including an HTTPS URI within the
Provided-By element). This document defines a namespace and adds the
namespace to the "provided-by" registry defined by PIDF-LO [RFC4119].
4. Transmitting Blocks of Additional Data
One or more blocks of data registered in the Emergency Call
Additional Data registry, as defined in Section 14.1, may be included
or referenced in the SIP signaling (using the Call-Info header field)
or in the provided-by element of a PIDF-LO. Each block is a MIME
type, and any set of blocks may be included.
Additional data about a call is defined as a series of MIME objects,
each with an XML data structure contained inside. As usual, whenever
more than one MIME part is included in the body of a message, MIME-
multipart (i.e., 'multipart/mixed') encloses them all. The sections
below define the XML schema and MIME types used for each block. When
Rosen, et al. Expires November 06, 2013 [Page 7]
Internet-Draft Additional Call Data May 2013
additional data is passed by value in the SIP signaling, each CID URL
points to one block in the body. Multiple URIs are used within a
Call-Info header field (or multiple Call-Info header fields) to point
to multiple blocks. When additional data is provided by reference
(in SIP signaling or Provided-By), each HTTPS URL references one
block; the data is retrieved with an HTTP GET operation, which
returns one of the blocks as an XML object.
A registry of allowed types is created by this document. Every block
must be one of the types in the registry.
In regions where callers can elect to suppress certain personally
identifying information, the network or PSAP functionality can
inspect privacy flags within the SIP headers to determine what
information may be passed, stored, or displayed to comply with local
policy or law.
Each entity adding additional data MUST supply the "Data Provider"
block. All other blocks are optional, but each entity SHOULD supply
any blocks where it has at least some of the information in the
block.
4.1. Transmitting blocks using Call-Info
A URI to a block MAY be inserted in a SIP request or response method
(most often INVITE or MESSAGE) with a Call-Info header field
containing a purpose of "emergencyCallData" together with the type of
data available at the URI. The type of data is denoted by including
the root of the MIME type (not including the emergencyCall prefix and
the +xml suffix) with a "." separator. For example, when
referencing a block with MIME type 'application/
emergencyCall.ProviderInfo+xml', the 'purpose' parameter is set to
'emergencyCallData.ProviderInfo'. An example "Call-Info" header
field for this would be:
Call-Info: https://www.example.com/23sedde3;
purpose="emergencyCallData.ProviderInfo"
The Call-info header with purpose='emergencyCallData' MUST only be
sent on an emergency call, which can be ascertained by the presence
of an emergency service urn in a Route header of a SIP message.
If the data is provided by reference, it may be retrieved with an
HTTPS GET from the URI. The URI MUST specify an HTTPS scheme, and
consequently Transport Layer Security (TLS) protection is applied.
Rosen, et al. Expires November 06, 2013 [Page 8]
Internet-Draft Additional Call Data May 2013
The data may also be supplied by value in a SIP message. In this
case, Content Indirection (CID) [RFC2392] is used, with the CID URL
referencing the MIME body part.
More than one Call-Info header with an emergencyCallData purpose can
be expected, but at least one MUST be provided. The device MUST
provide one if it knows no service provider is in the path of the
call. The device MAY insert one if it uses a service provider. Any
service provider in the path of the call MUST insert its own. For
example, a device, a telematics service provider in the call path, as
well as the mobile carrier handling the call will each provide one.
There may be circumstances where there is a service provider who is
unaware that the call is an emergency call and cannot reasonably be
expected to determine that it is an emergency call. In that case,
that service provider is not expected to provide emergencyCallData.
4.2. Transmitting blocks by reference using Provided-By
The 'emergencyCallDataReference' element is used to transmit an
additional data block by reference within a 'Provided-By' element of
a PIDF-LO. The 'emergencyCallDataReference' element has two
attributes: 'ref' to specify the URL, and 'purpose' to indicate the
type of data block referenced. The value of 'ref' is an HTTPS URL
that resolves to a data structure with information about the call.
The value of 'purpose' is the same as used in a 'Call-Info' header
field (as specified in section Section 4.1, Transmitting blocks using
Call-Info).
For example, to reference a block with MIME type 'application/
emergencyCall.ProviderInfo+xml', the 'purpose' parameter is set to
'emergencyCallData.ProviderInfo'. An example
'emergencyCallDataReference' element for this would be:
<emergencyCallDataReference ref="https://www.example.com/23sedde3"
purpose="emergencyCallData.ProviderInfo"/>
4.3. Transmitting blocks by value using Provided-By
It is RECOMMENDED that access networks supply the data specified in
this document by reference, but they MAY provide the data by value.
Rosen, et al. Expires November 06, 2013 [Page 9]
Internet-Draft Additional Call Data May 2013
The 'emergencyCallDataValue' element is used to transmit an
additional data block by value within a 'Provided-By' element of a
PIDF-LO. The 'emergencyCallDataValue' element has one attribute:
'purpose' to indicate the type of data block contained. The value of
'purpose' is the same as used in a 'Call-Info' header field (as
specified in Section 4.1, and in Section 4.1). The same XML
structure as would be wrapped in the corresponding MIME type is
placed inside the emergencyCallDataValue element.
For example:
<provided-by: xmlns="urn:ietf:params:xml:ns:
emergencyCallAddlData">
<emergencyCallDataValue purpose=
"emergencyCallData.ProviderInfo">
<ProviderID>HooThrooPoo</ProviderID>
<ProviderIDSeries>NENA</ProviderIDSeries>
<TypeOfProviderID>Access Infrastructure Provider
</TypeOfProviderID>
<ContactURI>sip:15555550987@burf.example.com;user=phone
</ContactURI>
</emergencyCallDataValue>
</provided-by>
Example Provided-By by Value.
5. Data Provider Information
This block is intended to be provided by any service provider in the
path of the call or the access network provider. It includes
identification and contact information. This block SHOULD be
provided by every service provider in the call path, and by the
access network provider. Devices MAY use this block to provide
identifying information. The MIME subtype is "application/
emergencyCall.ProviderInfo+xml".
5.1. Data Provider String
Data Element: Data Provider String
Use: Required
XML Element: <DataProviderString>
Rosen, et al. Expires November 06, 2013 [Page 10]
Internet-Draft Additional Call Data May 2013
Description: This is a plain language string suitable for displaying
the name of the service provider that created the additional data
structure. If the device created the structure the value is
identical to the contact header in the SIP INVITE.
Reason for Need: Inform the call taker of the identity of the entity
providing the additional call data structure.
How Used by Call Taker: Allows the call taker to interpret the data
in this structure. The source of the information often influences
how the information is used, believed or verified.
5.2. Data Provider ID
Data Element: Data Provider ID
Use: Conditional. Must be provided if the service provider is
located in a jurisdiction that maintains such ids. Devices are
not required to provide it.
XML Element: <ProviderID>
Description: A jurisdiction specific code for the provider shown in
the <DataProvidedBy> element that created the structure of the
call. This data SHOULD be provided if the local jurisdiction
maintains such an ID list. For example, in North America, this
would be a "NENA Company ID". Devices SHOULD NOT use this
element.
Reason for Need: Inform the call taker of the identity of the entity
providing the additional call data structure.
How Used by Call Taker: Where jurisdictions have lists of providers
the Data Provider ID can be useful.
5.3. Data Provider ID Series
Data Element: Data Provider ID Series
Use: Conditional. If Data Provider ID is provided, Data Provider ID
Series is required.
Rosen, et al. Expires November 06, 2013 [Page 11]
Internet-Draft Additional Call Data May 2013
XML Element: <ProviderIDSeries>
Description: Identifies the issuer of the the ProviderId. A
registry will reflect the following valid entries:
* NENA
* EENA
Reason for Need: Identifies how to interpret the Data Provider ID.
How Used by Call Taker: Determines which provider ID registry to
consult for more information
5.4. Type of Data Provider
Data Element: Type of Data Provider ID
Use: Conditional. If Data Provider ID is provided, Type of Data
Provider ID is required.
XML Element: <TypeOfProviderID>
Description: Identifies the type of data provider id being supplied
in the ProviderId data element. A registry will reflect the
following valid entries:
* Access Network Provider
* Service Provider
* Service Provider Subcontractor
* Telematics Provider
* Relay Provider
* Other
Reason for Need: Identifies what kind of data provider this is.
Rosen, et al. Expires November 06, 2013 [Page 12]
Internet-Draft Additional Call Data May 2013
How Used by Call Taker: To decide who to contact when further
information is needed
5.5. Data Provider Contact URI
Data Element: Data Provider Contact URI
Use: Required
XML Element: <ContactURI>
Description: For a service provider the contact SHOULD be a contact
URI. This MUST be a SIP URI. If a telephone number is the
contact address it should be provided in the form of
sip:telephonenumber@serviceprovider:user=phone. If the call is
from a device, this would reflect the contact information of the
owner of the device. When provided by a service provider, this
would be a URI to a 24/7 support organization tasked to provide
PSAP support for this emergency call.
Reason for Need: Additional data providers may need to be contacted
for error or other unusual circumstances.
How Used by Call Taker: To contact the supplier of the additional
data for assistance in handling the call.
5.6. Data Provider Languages(s) Supported
Data Element: Data Provider Language(s) supported
Use: Conditional
XML Element: <Language>
Description: The language used by the entity at the Data Provider
Contact URI as an alpha 2-character code as defined in ISO
639-1:2002 Codes for the representation of names of languages --
Part 1: Alpha-2 code Multiple instances of this element may occur.
Order is significant; preferred language should appear first.
This data is required if a Data Provider Contact URI is provided.
Rosen, et al. Expires November 06, 2013 [Page 13]
Internet-Draft Additional Call Data May 2013
The content must reflect the languages supported at the contact
URI.
Reason for Need: Information needed to determine if emergency
service authority can communicate with the service provider or if
an interpreter will be needed.
How Used by Call Taker: If call taker cannot speak language(s)
supported by the service provider, a translation service will need
to be added to the conversation.
5.7. xCard of Data Provider
Data Element: xCard of Data Provider
Use: Optional
XML Element: <DataProviderContact>
Description: There are many fields in the xCARD and the creator of
the data structure is encouraged to provide as much information as
they have available. N, ORG, ADR, TEL, EMAIL are suggested at a
minimum. N should contain name of support group or device owner
as appropriate. If more than one TEL property is provided, a
parameter from the vCard Property Value registry MUST be specified
on each TEL. For encoding of the xCard this specification uses
the XML-based encoding specified in [RFC6351].
and is hereinafter referred to as "xCard"
Reason for Need: Information needed to determine additional contact
information.
How Used by Call Taker: Assists call taker by providing additional
contact information that may not be included in the SIP invite or
the PIDF-LO.
Rosen, et al. Expires November 06, 2013 [Page 14]
Internet-Draft Additional Call Data May 2013
5.8. Subcontractor Principal
Data Element: Subcontractor Principal
XML Element: <SubcontratorPrincipal>
Description: If the data provider is a subcontractor to another
provider such as an access infrastructure provider or telematics
provider, this element contains the DataProviderString of the
service provider to indicate which provider the subcontractor is
working for. This data is required if the Data Provider type is
subcontractor.
Reason for Need: Identify the entity the subcontractor works for.
How Used by Call Taker: Allows the call taker to understand what the
relationship between data providers and the service providers in
the path of the call are.
5.9. Subcontractor Priority
Data Element: Subcontractor Priority
Use: Required
XML Element: <SubcontractorPriority>
Description: If the subcontractor should be contacted first, this
element should have a "sub" value. If the access or origination
service provider should be contacted first, this element should
have a "main" value. This data is required if the Data Provider
type is "subcontractor".
Reason for Need: Inform the call taker whether the network operator
or the subcontractor should be contacted first if support is
needed.
How Used by Call Taker: To decide which entity to contact first if
assistance is needed.
Rosen, et al. Expires November 06, 2013 [Page 15]
Internet-Draft Additional Call Data May 2013
5.10. emergencyCall.ProviderInfo XML Schema
<?xml version="1.0"?>
<xs:schema
targetNamespace="urn:ietf:params:xml:ns:emergencyCall.ProviderInfo"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:ad="urn:ietf:params:xml:ns:emergencyCall.ProviderInfo"
xmlns:xml="http://www.w3.org/XML/1998/namespace"
xmlns:xc="urn:ietf:params:xml:ns:vcard-4.0"
elementFormDefault="qualified"
ttributeFormDefault="unqualified">
<xs:import namespace="http://www.w3.org/XML/1998/namespace"
schemaLocation="http://www.w3.org/2001/xml.xsd"/>
<xs:simpleType name="iso3166a2">
<xs:restriction base="xs:token">
<xs:pattern value="[A-Z]{2}"/>
</xs:restriction>
</xs:simpleType>
<xs:element name="emergencyCall.ProviderInfo">
<xs:complexType>
<xs:sequence>
<xs:element name="DataProviderString"
type="xs:string" minOccurs="1" maxOccurs="1"/>
<xs:element name="ProviderID"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:element name="ProviderIDSeries"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:element name="TypeOfProvider"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:element name="ContactURI" type="xs:anyURI"
minOccurs="1" maxOccurs="1"/>
<xs:element name="Language" type="ad:iso3166a2"
minOccurs="0" maxOccurs="unbounded" />
<xs:element name="DataProviderContact"
type="xc:vcardType" minOccurs="0"
maxOccurs="1"/>
<xs:any namespace="##other" processContents="lax"
minOccurs="0" maxOccurs="unbounded"/>
</xs:sequence>
</xs:complexType>
</xs:element>
</xs:schema>
Rosen, et al. Expires November 06, 2013 [Page 16]
Internet-Draft Additional Call Data May 2013
Figure 1: emergencyCall.ProviderInfo XML Schema
5.11. emergencyCall.ProviderInfo Example
<?xml version="1.0" encoding="UTF-8"?>
<ad:emergencyCall.ProviderInfo
xmlns:ad="urn:ietf:params:xml:ns:emergencyCall.ProviderInfo"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<ad:DataProviderString>Example VoIP Provider
</ad:DataProviderString>
<ad:ProviderID>ID123</ad:ProviderID>
<ad:ProviderIDSeries>NENA</ad:ProviderIDSeries>
<ad:TypeOfProvider>Service Provider</ad:TypeOfProvider>
<ad:ContactURI>sip:voip-provider@example.com</ad:ContactURI>
<ad:Language>EN</ad:Language>
<xc:DataProviderContact
xmlns:xc="urn:ietf:params:xml:ns:vcard-4.0">
<vcard>
<fn><text>Hannes Tschofenig</text></fn>
<n>
<surname>Hannes</surname>
<given>Tschofenig</given>
<additional/>
<prefix/>
<suffix>Dipl. Ing.</suffix>
</n>
<bday><date>--0203</date></bday>
<anniversary>
<date-time>20090808T1430-0500</date-time>
</anniversary>
<gender><sex>M</sex></gender>
<lang>
<parameters><pref><integer>1</integer></pref>
</parameters>
<language-tag>de</language-tag>
</lang>
<lang>
<parameters><pref><integer>2</integer></pref>
</parameters>
<language-tag>en</language-tag>
</lang>
<org>
<parameters><type><text>work</text></type>
</parameters>
<text>Example VoIP Provider</text>
</org>
<adr>
Rosen, et al. Expires November 06, 2013 [Page 17]
Internet-Draft Additional Call Data May 2013
<parameters>
<type><text>work</text></type>
<label><text>Hannes Tschofenig
Linnoitustie 6
Espoo , Finland
02600</text></label>
</parameters>
<pobox/>
<ext/>
<street>Linnoitustie 6</street>
<locality>Espoo</locality>
<region>Uusimaa</region>
<code>02600</code>
<country>Finland</country>
</adr>
<tel>
<parameters>
<type>
<text>work</text>
<text>voice</text>
</type>
</parameters>
<uri>tel:+358 50 4871445</uri>
</tel>
<email>
<parameters><type><text>work</text></type>
</parameters>
<text>hannes.tschofenig@nsn.com</text>
</email>
<geo>
<parameters><type><text>work</text></type>
</parameters>
<uri>geo:60.210796,24.812924</uri>
</geo>
<key>
<parameters><type><text>home</text></type>
</parameters>
<uri>
http://www.tschofenig.priv.at/key.asc
</uri>
</key>
<tz><text>Finland/Helsinki</text></tz>
<url>
<parameters><type><text>home</text></type>
</parameters>
<uri>http://www.tschofenig.priv.at</uri>
</url>
</vcard>
Rosen, et al. Expires November 06, 2013 [Page 18]
Internet-Draft Additional Call Data May 2013
</xc:DataProviderContact>
</ad:emergencyCall.ProviderInfo>
Figure 2: emergencyCall.ProviderInfo Example
6. Service Information
This block describes the service that the service provider provides
to the caller. It SHOULD be included by all SPs in the path of the
call. The mime subtype is "application/emergencyCall.SvcInfo+xml".
6.1. Service Environment
Data Element: Service Environment
Use: Required
XML Element: <SvcEnvironment>
Description: This element defines whether a call is from a business
or residence caller. Currently, the only valid entries are
'Business' or 'Residence'.
Reason for Need: To assist in determining equipment and manpower
requirements.
How Used by Call Taker: Information may be used to assist in
determining equipment and manpower requirements for emergency
responders. As the information is not always available, and the
registry is not all encompassing, this is at best advisory
information, but since it mimics a similar capability in some
current emergency calling systems, it is known to be valuable.
The service provider uses its best information (such as a rate
plan, facilities used to deliver service or service description)
to determine the information and is not responsible for
determining the actual characteristics of the location where the
call originates from.
Rosen, et al. Expires November 06, 2013 [Page 19]
Internet-Draft Additional Call Data May 2013
6.2. Service Delivered by Provider to End User
Data Element: Service Delivered by Provider to End User
Use: Required
XML Element: <SvcDelByProvider>
Description: This defines the type of service the end user has
subscribed to. The implied mobility of this service can not be
relied upon. A registry defined in this document will reflect the
following initial valid entries:
* Wireless Telephone Service: Includes Satellite, CDMA, GSM, Wi-
Fi, WiMAX, UTMS/WCDMA, LTE (Long Term Evolution)
* Fixed Public Pay/Coin telephones: Any coin or credit card
operated device.
* One way outbound service
* Inmate call/service
* Soft dialtone/quick service/warm disconnect/suspended
* Multi-line telephone system (MLTS): Includes all PBX, Centrex,
key systems, Shared Tenant Service.
* Sensor, unattended: Includes devices that generate DATA ONLY.
This is one-way information exchange and there will be no other
form of communication.
* Sensor, attended: Includes devices that are supported by a
monitoring service provider or automatically open a two-way
communication path.
* Wireline: Plain Old Telephone Service (POTS).
* VoIP Telephone Service: A type of service that offers
communication over internet protocol, such as Fixed, Nomadic,
Mobile, Unknown
Rosen, et al. Expires November 06, 2013 [Page 20]
Internet-Draft Additional Call Data May 2013
* Relay Service: a type of service where there is a human 3rd
party agent who provides some kind of additional assistance to
the caller. Includes sign language relay and telematics
services which provide a service assistant on the call.
* Remote (off premise extension)
There can be more than one value returned. For example, a VoIP
inmate telephone service is a reasonable combination.
Reason for Need: Knowing the type of service may assist the PSAP
with the handling of the call.
How Used by Call Taker: Call takers often use this information to
determine what kinds of questions to ask callers, and how much to
rely on supportive information. An emergency call from a prison
is treated differently that a call from a sensor device. As the
information is not always available, and the registry is not all
encompassing, this is at best advisory information, but since it
mimics a similar capability in some current emergency calling
systems, it is known to be valuable.
6.3. Service Mobility Environment
Data Element: Service Mobility Environment
Use: Required
XML Element: <SvcMobility>
Description: This provides the service providers view of the
mobility of the caller. As the service provider may not know the
characteristics of the actual access network used, the value not
be relied upon. A registry will reflect the following initial
valid entries:
* Mobile: the device should be able to move at any time
* Fixed: the device is not expected to move unless the service is
relocated
* Nomadic: the device is not expected to change its point of
attachment while on a call
Rosen, et al. Expires November 06, 2013 [Page 21]
Internet-Draft Additional Call Data May 2013
* Unknown: no information is known about the service mobility
environment for the device
Reason for Need: Knowing the service provider's belief of mobility
may assist the PSAP with the handling of the call.
How Used by Call Taker: To determine whether to assume the location
of the caller might change.
6.4. emergencyCall.SvcInfo XML Schema
<?xml version="1.0"?>
<xs:schema
targetNamespace="urn:ietf:params:xml:ns:emergencyCall.SvcInfo"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:svc="urn:ietf:params:xml:ns:emergencyCall.SvcInfo"
xmlns:xml="http://www.w3.org/XML/1998/namespace"
elementFormDefault="qualified"
attributeFormDefault="unqualified">
<xs:import namespace="http://www.w3.org/XML/1998/namespace"
schemaLocation="http://www.w3.org/2001/xml.xsd"/>
<xs:element name="emergencyCall.SvcInfo">
<xs:complexType>
<xs:sequence>
<xs:element name="SvcEnvironment"
type="xs:string" minOccurs="1" maxOccurs="1"/>
<xs:element name="SvcDelByProvider"
type="xs:string" minOccurs="1" maxOccurs="1"/>
<xs:element name="SvcMobility"
type="xs:string" minOccurs="1" maxOccurs="1"/>
<xs:element name="Link"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:any namespace="##other" processContents="lax"
minOccurs="0" maxOccurs="unbounded"/>
</xs:sequence>
</xs:complexType>
</xs:element>
</xs:schema>
Figure 3: emergencyCall.SvcInfo XML Schema
6.5. emergencyCall.SvcInfo Example
Rosen, et al. Expires November 06, 2013 [Page 22]
Internet-Draft Additional Call Data May 2013
<?xml version="1.0" encoding="UTF-8"?>
<svc:emergencyCall.SvcInfo
xmlns:svc="urn:ietf:params:xml:ns:emergencyCall.SvcInfo"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<svc:SvcEnvironment>Business</svc:SvcEnvironment>
<svc:SvcDelByProvider>MLTS</svc:SvcDelByProvider>
<svc:SvcMobility>Fixed</svc:SvcMobility>
</svc:emergencyCall.SvcInfo>
Figure 4: emergencyCall.SvcInfo Example
7. Device Information
This block provides information about the device used to place the
call. It should be provided by any service provider that knows what
device is being used, and by the device itself. The mime subtype is
"application/emergencyCall.DevInfo+xml".
7.1. Device Classification
Data Element: Device Classification
Use: Optional
XML Element: <DeviceClassification>
Description: This data element defines the kind of device making the
emergency call. If the device provides the data structure, the
device information SHOULD be provided. If the service provider
provides the structure and it knows what the device is, the
service provider SHOULD provide the device information. Often the
carrier does not know what the device is. It is possible to
receive two Additional Data Associated with a Call data
structures, one created by the device and one created by the
service provider. This information describes the device, not how
it is being used. This data element defines the kind of device
making the emergency call. A registry will reflect the following
valid entries:
* Cordless handset
* Fixed phone
* Mobile handset
Rosen, et al. Expires November 06, 2013 [Page 23]
Internet-Draft Additional Call Data May 2013
* ATA (analog terminal adapter)
* Satellite phone
* Stationary computing device (alarm system, data sensor)
* Guardian devices
* Desktop PC
* Laptop computing device
* Tablet computing device
* Alarm system
* Data sensor
* Personal beacons (spot)
* Auto telematics (indicates VEDS data set)
* Trucking telematics
* Farm equipment telematics
* Marine telematics
* PDA (personal digital assistant)
* PND (personal navigation device)
* Smart phone
* Internet tablet
* Gaming console
* Video phone
* Other text device
* Not Available
Reason for Need: The device classification implies the capability of
the calling device and assists in identifying the meaning of the
emergency call location information that is being presented. For
Rosen, et al. Expires November 06, 2013 [Page 24]
Internet-Draft Additional Call Data May 2013
example, does the device require human intervention to initiate a
call or is this call the result of programmed instructions? Does
the calling device have the ability to update location or
condition changes? Is this device interactive or a one-way
reporting device?
How Used by Call Taker: May assist with location of caller. For
example, a cordless handset may be outside or next door. May
provide calltaker some context about the caller, the capabilities
of the device used for the call or the environment the device is
being used in.
7.2. Device Manufacturer
Data Element: Device Manufacturer
Use: Optional
XML Element: <DeviceMfgr>
Description: The plain language name of the manufacturer of the
device.
Reason for Need: Used by PSAP management for post-mortem
investigation/resolution.
How Used by Call Taker: Probably not used by calltaker, but by PSAP
management.
7.3. Device Model Number
Data Element: Device Model Number
Use: Optional
XML Element: <DeviceModelNr>
Description: Model number of the device.
Rosen, et al. Expires November 06, 2013 [Page 25]
Internet-Draft Additional Call Data May 2013
Reason for Need: Used by PSAP management for after action
investigation/resolution.
How Used by Call Taker: Probably not used by calltaker, but by PSAP
management.
7.4. Unique Device Identifier
Data Element: Unique Device Identifier
Use: Optional
XML Element: <UniqueDeviceID>
Description: String that identifies the specific device making the
call or creating an event.
Reason for Need: Uniquely identifies the device as opposed to any
signaling identifiers encountered in the call signaling stream.
How Used by Call Taker: Probably not used by calltaker they would
need to refer to management for investigation.
7.5. Type of Device Identifier
Data Element: Type of Device Identifier
Use: Conditional: must be provided if DeviceID is provided
XML Element: <TypeOfDeviceID>
Description: Identifies the type of device identifier being
generated in the unique device identifier data element. A
registry will reflect the following valid entries:
* MEID (CDMA)
* ESN (Electronic Serial Number -- superseded by MEID)
Rosen, et al. Expires November 06, 2013 [Page 26]
Internet-Draft Additional Call Data May 2013
* MAC (Media Access Control) Address -- IEEE-delegated address of
any of the interfaces of the device with a MAC address (e.g.,
Ethernet, WiFi)
* WiMAX device certificate subject unique identifier
* IMEI (International Mobile Equipment Identifier - GSM)
* Unique Device Identifier (UDI) assigned by US FDA for medical
devices
* RFID (Radio Frequency Identification)
* Sensors (types to be identified in a future document version)
* Manufacturer Serial Number
* Other
Reason for Need: Identifies how to interpret the Unique Device
Identifier.
How Used by Call Taker: Additional information that may be used to
assist with call handling.
7.6. Device/Service Specific Additional Data Structure
Data Element: Device/service specific additional data structure
Use: Optional
XML Element: <DeviceSpecificData>
Description: A URI representing additional data whose schema is
specific to the device or service which created it. An example is
the VEDs structure for a vehicle telematics device. The URI, when
dereferenced, MUST yield a data structure defined by the Device/
service specific additional data type value. Different data may
be created by each classification; e.g., telematics creates VEDS
data set.
Rosen, et al. Expires November 06, 2013 [Page 27]
Internet-Draft Additional Call Data May 2013
Reason for Need: Provides device/service specific data that may be
used by the call taker and/or responders.
How Used by Call Taker: Provide information to guide call takers to
select appropriate responders, give appropriate pre-arrival
instructions to callers, and advise responders of what to be
prepared for. May be used by responders to guide assistance
provided.
7.7. Device/Service Specific Additional Data Structure Type
Data Element: Type of Device/service specific additional data
structure
Use: Conditional. MUST be provided when Device/service specific
additional URI is provided
XML Element: <DeviceSpecificType>
Description: Value from a registry defined by this document to
describe the type of data that can be retrieved from the Device/
service specific additional data structure. Initial values are:
* IEEE 1512 - USDOT Model for traffic incidents
* VEDS
Reason for Need: This data element allows identification of
externally defined schemas, which may have additional data that
may assist in emergency response.
How Used by Call Taker: This data element allows the end user
(calltaker or first responder) to know what type of additional
data may be available to aid in providing the needed emergency
services.
Note: Information which is specific to a location or a caller
(person) should not be placed in this section.
7.8. Choosing between defining a new type of block or new type of
device/service specific additional data
Rosen, et al. Expires November 06, 2013 [Page 28]
Internet-Draft Additional Call Data May 2013
For devices that have device or service specific data, there are two
choices to carry it. A new block can be defined, or the device/
service specific additional data URL the the DevInfo block can be
used and a new type for it defined . The data passed would likely be
the same in both cases. Considerations for choosing which mechanism
to register under include:
Applicability: Information which will be carried by many kinds of
devices or services are more appropriately defined as separate
blocks.
Privacy: Information which may contain private data may be better
sent in the DevInfo block, rather than a new block so that
implementations are not tempted to send the data by value, and
thus having more exposure to the data than forcing the data to be
retrieved via the URL in DevInfo.
Size: Information which may be very may be better sent in the
DevInfo block, rather than a new block so that implementations are
not tempted to send the data by value. Conversely, data which is
small may best be sent in a separate block so that it can be sent
by value
Availability of a server: Providing the data via the device block
requires a server be made available to retrieve the data.
Providing the data via new block allows it to be sent by value
(CID).
7.9. emergencyCall.DevInfo XML Schema
<?xml version="1.0"?>
<xs:schema
targetNamespace="urn:ietf:params:xml:ns:emergencyCall.DevInfo"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:svc="urn:ietf:params:xml:ns:emergencyCall.DevInfo"
xmlns:xml="http://www.w3.org/XML/1998/namespace"
elementFormDefault="qualified"
attributeFormDefault="unqualified">
<xs:import namespace="http://www.w3.org/XML/1998/namespace"
schemaLocation="http://www.w3.org/2001/xml.xsd"/>
<xs:element name="emergencyCall.DevInfo">
<xs:complexType>
<xs:sequence>
<xs:element name="DeviceClassification"
type="xs:string" minOccurs="0" maxOccurs="1"/>
Rosen, et al. Expires November 06, 2013 [Page 29]
Internet-Draft Additional Call Data May 2013
<xs:element name="DeviceMfgr"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:element name="DeviceModelNr"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:element name="UniqueDeviceID"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:element name="TypeOfDeviceID"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:element name="DeviceSpecificData"
type="xs:anyURI" minOccurs="0" maxOccurs="1"/>
<xs:element name="DeviceSpecificType"
type="xs:string" minOccurs="0" maxOccurs="1"/>
<xs:any namespace="##other" processContents="lax"
minOccurs="0" maxOccurs="unbounded"/>
</xs:sequence>
</xs:complexType>
</xs:element>
</xs:schema>
Figure 5: emergencyCallDevInfo XML Schema
7.10. emergencyCall.DevInfo Example
<?xml version="1.0" encoding="UTF-8"?>
<svc:emergencyCall.DevInfo
xmlns:svc="urn:ietf:params:xml:ns:emergencyCall.DevInfo"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<svc:DeviceClassification>Fixed phone</svc:DeviceClassification>
<svc:DeviceMfgr>Nokia</svc:DeviceMfgr>
<svc:DeviceModelNr>Lumia 800</svc:DeviceModelNr>
<svc:UniqueDeviceID>35788104</svc:UniqueDeviceID>
<svc:TypeOfDeviceID>IMEI</svc:TypeOfDeviceID>
</svc:emergencyCall.DevInfo>
Figure 6: emergencyCallDevInfo Example
8. Owner/Subscriber Information
This block describes the owner of the device (if provided by the
device) or the subscriber information, if provided by a service
provider. The contact location is not necessarily the location of
the caller or incident, but is rather the nominal contact address.
The mime subtype is "application/emergencyCall.Subscriber+xml".
8.1. xCard for Subscriber's Data
Data Element: xCARD for Subscriber's Data
Rosen, et al. Expires November 06, 2013 [Page 30]
Internet-Draft Additional Call Data May 2013
Use: Conditional: Some services (e.g., prepaid phones, initialized
phones, etc.) may not have this information.
XML Element: <SubscriberData>
Description: Information known by the service provider or device
about the subscriber; e.g., Name, Address, Individual Telephone
Number, Main Telephone Number and any other data. N, ORG (if
appropriate), ADR, TEL, EMAIL are suggested at a minimum. If more
than one TEL property is provided, a parameter from the vCard
Property Value registry MUST be specified on each TEL.
Reason for Need: When the caller is unable to provide information,
this data may be used to obtain it
How Used by Call Taker: Obtaining critical information about the
caller and possibly the location when it is not able to be
obtained otherwise.
8.2. emergencyCall.SubInfo XML Schema
<?xml version="1.0"?>
<xs:schema
targetNamespace="urn:ietf:params:xml:ns:emergencyCall.SubInfo"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:sub="urn:ietf:params:xml:ns:emergencyCall.SubInfo"
xmlns:xml="http://www.w3.org/XML/1998/namespace"
xmlns:xc="urn:ietf:params:xml:ns:vcard-4.0"
elementFormDefault="qualified" attributeFormDefault="unqualified">
<xs:import namespace="http://www.w3.org/XML/1998/namespace"
schemaLocation="http://www.w3.org/2001/xml.xsd"/>
<xs:element name="emergencyCall.SubInfo">
<xs:complexType>
<xs:sequence>
<!-- VCard data structure goes in here.
<xs:element name="SubscriberData"
type="xc:vcard" minOccurs="0" maxOccurs="1"/>
-->
<xs:any namespace="##other" processContents="lax"
minOccurs="0" maxOccurs="unbounded"/>
</xs:sequence>
Rosen, et al. Expires November 06, 2013 [Page 31]
Internet-Draft Additional Call Data May 2013
</xs:complexType>
</xs:element>
</xs:schema>
Figure 7: emergencyCall.SubInfo XML Schema
8.3. emergencyCall.SubInfo Example
<?xml version="1.0" encoding="UTF-8"?>
<ad:emergencyCall.SubInfo
xmlns:ad="urn:ietf:params:xml:ns:emergencyCall.SubInfo"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<xc:SubscriberData xmlns:xc="urn:ietf:params:xml:ns:vcard-4.0">
<vcards xmlns="urn:ietf:params:xml:ns:vcard-4.0">
<vcard>
<fn><text>Simon Perreault</text></fn>
<n>
<surname>Perreault</surname>
<given>Simon</given>
<additional/>
<prefix/>
<suffix>ing. jr</suffix>
<suffix>M.Sc.</suffix>
</n>
<bday><date>--0203</date></bday>
<anniversary>
<date-time>20090808T1430-0500</date-time>
</anniversary>
<gender><sex>M</sex></gender>
<lang>
<parameters><pref><integer>1</integer></pref>
</parameters>
<language-tag>fr</language-tag>
</lang>
<lang>
<parameters><pref><integer>2</integer></pref>
</parameters>
<language-tag>en</language-tag>
</lang>
<org>
<parameters><type><text>work</text></type>
</parameters>
<text>Viagenie</text>
</org>
<adr>
<parameters>
<type><text>work</text></type>
Rosen, et al. Expires November 06, 2013 [Page 32]
Internet-Draft Additional Call Data May 2013
<label><text>Simon Perreault
2875 boul. Laurier, suite D2-630
Quebec, QC, Canada
G1V 2M2</text></label>
</parameters>
<pobox/>
<ext/>
<street>2875 boul. Laurier, suite D2-630</street>
<locality>Quebec</locality>
<region>QC</region>
<code>G1V 2M2</code>
<country>Canada</country>
</adr>
<tel>
<parameters>
<type>
<text>work</text>
<text>voice</text>
</type>
</parameters>
<uri>tel:+1-418-656-9254;ext=102</uri>
</tel>
<tel>
<parameters>
<type>
<text>work</text>
<text>text</text>
<text>voice</text>
<text>cell</text>
<text>video</text>
</type>
</parameters>
<uri>tel:+1-418-262-6501</uri>
</tel>
<email>
<parameters><type><text>work</text></type>
</parameters>
<text>simon.perreault@viagenie.ca</text>
</email>
<geo>
<parameters><type><text>work</text></type>
</parameters>
<uri>geo:46.766336,-71.28955</uri>
</geo>
<key>
<parameters><type><text>work</text></type>
</parameters>
<uri>
Rosen, et al. Expires November 06, 2013 [Page 33]
Internet-Draft Additional Call Data May 2013
http://www.viagenie.ca/simon.perreault/simon.asc
</uri>
</key>
<tz><text>America/Montreal</text></tz>
<url>
<parameters><type><text>home</text></type>
</parameters>
<uri>http://nomis80.org</uri>
</url>
</vcard>
</vcards>
</xc:SubscriberData>
</ad:emergencyCall.SubInfo>
Figure 8: emergencyCall.SubInfo Example
9. Comment
This block provides a mechanism for the data provider to supply
extra, human readable information to the PSAP. It is not intended
for a general purpose extension mechanism. The mime subtype is
"application/emergencyCall.Comment+xml"
9.1. Comment
Data Element: EmergencyCall.Comment
Use: Optional
XML Element: <Comment>
Description: Human readable text providing additional information to
the PSAP staff.
Reason for Need: Explanatory information for values in the data
structure
How Used by Call Taker: To interpret the data provided
9.2. emergencyCall.Comment XML Schema
<?xml version="1.0"?>
Rosen, et al. Expires November 06, 2013 [Page 34]
Internet-Draft Additional Call Data May 2013
<xs:schema
targetNamespace="urn:ietf:params:xml:ns:emergencyCall.Comment"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:sub="urn:ietf:params:xml:ns:emergencyCall.Comment"
xmlns:xml="http://www.w3.org/XML/1998/namespace"
elementFormDefault="qualified" attributeFormDefault="unqualified">
<xs:import namespace="http://www.w3.org/XML/1998/namespace"
schemaLocation="http://www.w3.org/2001/xml.xsd"/>
<xs:element name="emergencyCall.Comment">
<xs:complexType>
<xs:sequence>
<xs:element name="Comment"
type="sub:CommentType" minOccurs="0" maxOccurs="unbounded"/>
<xs:any namespace="##other" processContents="lax" minOccurs="0"
maxOccurs="unbounded"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:complexType name="CommentType">
<xs:simpleContent>
<xs:extension base="xs:string">
<xs:attribute ref="xml:lang"/>
</xs:extension>
</xs:simpleContent>
</xs:complexType>
</xs:schema>
Figure 9: EmergencyCall.Comment XML Schema
9.3. emergencyCall.Comment Example
<?xml version="1.0" encoding="UTF-8"?>
<sub:emergencyCall.Comment
xmlns:sub="urn:ietf:params:xml:ns:emergencyCall.Comment"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<sub:Comment xml:lang="en">This is an example text.</sub:Comment>
</sub:emergencyCall.Comment>
Figure 10: EmergencyCall.Comment Example
10. Example
Rosen, et al. Expires November 06, 2013 [Page 35]
Internet-Draft Additional Call Data May 2013
INVITE sips:bob@biloxi.example.com SIP/2.0
Via: SIPS/2.0/TLS pc33.atlanta.example.com;branch=z9hG4bK74bf9
Max-Forwards: 70
To: Bob <sips:bob@biloxi.example.com>
From: Alice <sips:alice@atlanta.example.com>;tag=9fxced76sl
Call-ID: 3848276298220188511@atlanta.example.com
Call-Info: <http://wwww.example.com/alice/photo.jpg> ;purpose=icon,
<http://www.example.com/alice/> ;purpose=info,
<cid:1234567890@atlanta.example.com>
;purpose=emergencyCallData.ProviderInfo
Geolocation: <cid:target123@atlanta.example.com>
Geolocation-Routing: no
Accept: application/sdp, application/pidf+xml,
application/emergencyCallProviderinfo+xml
CSeq: 31862 INVITE
Contact: <sips:alice@atlanta.example.com>
Content-Type: multipart/mixed; boundary=boundary1
Content-Length: ...
--boundary1
Content-Type: application/sdp
...SDP goes here
--boundary1
Content-Type: application/pidf+xml
Content-ID: <target123@atlanta.example.com>
\0x2026PIDF-LO goes here
--boundary1--
Content-Type: application/emergencyCall.ProviderInfo+xml
Content-ID: <1234567890@atlanta.example.com>
...Additional Data goes here
--boundary1--
Example: Attaching Additional Data via CID to a SIP INVITE
11. Main Telephone Number
In a xCard, used extensively in this document, there is no way to
specify a "Main" telephone number. These numbers are useful to
Rosen, et al. Expires November 06, 2013 [Page 36]
Internet-Draft Additional Call Data May 2013
emergency responders who are called to a large enterprise. This
document adds a new Property Value to the "tel" property of the TYPE
parameter called "main". It can be used in any xCard in additional
data.
12. Security Considerations
The information in this data structure will usually be considered
private. HTTPS is specified to require the provider of the
information to validate the credentials of the requester. While the
creation of a PKI that has global scope may be difficult, the
alternatives to creating devices and services that can provide
critical information securely are more daunting. The provider may
enforce any policy it wishes to use, but PSAPs and responder agencies
should deploy a PKI so that providers of additional data can check
the certificate of the client and decide the appropriate policy to
enforce based on that certificate.
Ideally, the PSAP and emergency responders will be given credentials
signed by an authority trusted by the data provider. In most
circumstances, nationally recognized credentials would be sufficient,
and if the emergency services arranges a PKI, data providers could be
provisioned with the root CA public key for a given nation. Some
nations are developing a PKI for this, and related, purposes. Since
calls could be made from devices where the device and/or the service
provider(s) are not local to the emergency authorities, globally
recognized credentials are useful. This might be accomplished by
extending the notion of the "forest guide" described in [RFC5222] to
allow the forest guide to provide the credential of the PKI root for
areas that it has coverage information for, but standards for such a
mechanism are not yet available. In its absence, the data provider
will need to obtain the root CA credentials for any areas it is
willing to provide additional data by out of band means. With the
credential of the root CA for a national emergency services PKI, the
data provider server can validate the credentials of an entity
requesting additional data by reference.
The data provider also needs a credential that can be verified by the
emergency services to know that it is receiving data from the right
server. The emergency authorities could provide credentials,
distinguishable from credentials it provides to emergency responders
and PSAPs, which could be used to validate data providers. Such
credentials would have to be acceptable to any PSAP or responder that
could receive a call with additional data supplied by that provider.
This would be extensible to global credential validation using the
forest guide as above. In the absence of such credentials, the
emergency authorities could maintain a list of local data providers'
credentials provided to it out of band. At a minimum, the emergency
Rosen, et al. Expires November 06, 2013 [Page 37]
Internet-Draft Additional Call Data May 2013
authorities could obtain a credential from the DNS entry of the
domain in the Addional Data URI to at least validate that the server
is known to the domain providing the URI.
Data provided by devices by reference have similar credential
validation issues to service providers, and the solutions are the
same.
13. Privacy Considerations
There is much private data in this information. Local regulations
may govern what data must be provided in emergency calls, but in
general, the emergency call system is often aided by the kinds of
information described in this document. There is a tradeoff between
the privacy considerations and the utility of the data. Certainly,
if the data cannot be protected, due to failure to establish (by TLS)
a secure connection to the data provider, data SHOULD NOT be sent
unless specifically required by regulation.
Some forms of data can be sent by value in the SIP signaling or by
value (URL in SIP signaling). When data is sent by value, all
intermediaries have access to the data. If the data is private,
sending by reference is more appropriate.
14. IANA Considerations
14.1. Registry creation
This document creates a new registry called 'Emergency Call
Additional Data'. The following subregistries are created in
Emergency Call Additional Data:
14.1.1. Additional Call Data Provider ID Series Registry
This document creates a new subregistry called 'Additional Call Data
Provider ID Series'. As defined in [RFC5226], this registry operates
under "Expert Review" rules. The expert should determine that the
entity requesting a new value is a legitimate issuer of service
provider IDs suitable for use in Additional Call Data.
The content of this registry includes:
Name: The identifier which will be used in the ProviderIDSeries
element
Source: The full name of the organization issuing the identifiers
URL: A URL to the organization for further information
Rosen, et al. Expires November 06, 2013 [Page 38]
Internet-Draft Additional Call Data May 2013
The values defined are:
+-----------+-----------+--------------+--------------+
| Name | Source | URL |
+-----------+--------------------------+--------------+
| NENA | North American Emergency | www.nena.org |
| | Number Association | |
| EENA | European Emergency | www.eena.org |
| | Number Association | |
+-----------+--------------------------+--------------+
RFC Editor Note:
replace XXXX in the table above with this documents RFC number
14.1.2. Additional Call Data Service Provider Type Registry
This document creates a new subregistry called 'Service Provider
Type'. As defined in [RFC5226], this registry operates under "Expert
Review". The expert should determine that the proposed new value is
distinct from existing values and appropriate for use in the
TypeOfServicerProvider element
The content of this registry includes:
Name: Value to be used in TypeOfServiceProvider.
Description: A short description of the type of service provider
The values defined are:
+------------------------------+------------------------------------+
| Name | Description |
+------------------------------+------------------------------------+
|Access Infrastructure Provider| Access network service provider |
|Service Provider | Calling or Origination telecom SP |
|Service Provider Subcontractor| A contractor to another kind of SP |
|Telematics Provider | A sensor based SP, especially |
| | vehicle based |
|Relay Provider | A interpretation SP, for example, |
| | video relay for sign language |
| | interpretors |
|Other | Any other type of service provider |
+------------------------------+------------------------------------+
RFC Editor Note:
replace XXXX in the table above with this documents RFC number
Rosen, et al. Expires November 06, 2013 [Page 39]
Internet-Draft Additional Call Data May 2013
14.1.3. Additional Call Data Service Delivered Registry
This document creates a new registry called 'Additional Call Data
Service Delivered'. As defined in [RFC5226], this registry operates
under "Expert Review" rules. The expert should consider whether the
proposed service is unique from existing services and the definition
of the service will be clear to implementors and PSAPS/responders.
The content of this registry includes:
Name: enumeration token of the service.
Description: Short description identifying the service.
The values defined are:
+--------+----------------------------------------+
| Name | Description |
+--------+----------------------------------------+
| Wrless | Wireless Telephone Service: Includes |
| | Satellite, CDMA, GSM, Wi-Fi, WiMAX, |
| | LTE (Long Term Evolution) |
| Coin | Fixed Public Pay/Coin telephones: Any |
| | coin or credit card operated device |
| 1way | One way outbound service |
| Prison | Inmate call/service |
| Temp | Soft dialtone/quick service/warm |
| | disconnect/suspended |
| MLTS | Multi-line telephone system: Includes |
| | all PBX, Centrex, key systems, |
| | Shared Tenant Service |
| SenseU | Sensor, unattended: Includes devices |
| | that generate DATA ONLY. This is |
| | one-way information exchange and |
| | there will be no other form of |
| | communication |
| SenseA | Sensor, attended: Includes devices |
| | that are supported by a monitoring |
| | service provider or automatically |
| | open a two-way communication path |
| POTS | Wireline: Plain Old Telephone Service |
| VOIP | VoIP Telephone Service: A type of |
| | service that offers communication |
| | over internet protocol, such as Fixed|
| | Nomadic, Mobile, ... |
+--------+----------------------------------------+
Rosen, et al. Expires November 06, 2013 [Page 40]
Internet-Draft Additional Call Data May 2013
14.1.4. Additional Call Data Device Classification Registry
This document creates a new registry called 'Additional Call Data
Device Classification'. As defined in [RFC5226], this registry
operates under "Expert Review" rules. The expert should consider
whether the proposed class is unique from existing classes and the
definition of the class will be clear to implementors and PSAPS/
responders.
The content of this registry includes:
Name: enumeration token of the device classification.
Description: Short description identifying the device type.
The values defined are:
+--------+----------------------------------------+
| Name | Description |
+--------+----------------------------------------+
|Cordless| Cordless handset |
| Fixed | Fixed phone |
| Mobile | Mobile handset |
| ATA | analog terminal adapter |
|Satphone| Satellite phone |
| FSense | Stationary computing device (alarm |
| | system, data sensor) |
| Guard | Guardian devices |
| Desktop| Desktop PC |
| Laptop | Laptop computing device |
| Tablet | Tablet computing device |
| Alarm | Alarm system |
| MSense | Mobile Data sensor |
| Beacon | Personal beacons (spot) |
| Auto | Auto telematics |
| Truck | Truck telematics |
| Farm | Farm equipment telematics |
| Marine | Marine telematics |
| PDA | Personal digital assistant |
| PND | Personal navigation device) |
| SmrtPhn| Smart phone |
| Itab | Internet tablet |
| Game | Gaming console |
| Video | Video phone |
| Text | Other text device |
| NA | Not Available |
+--------+----------------------------------------+
Rosen, et al. Expires November 06, 2013 [Page 41]
Internet-Draft Additional Call Data May 2013
14.1.5. Additional Call Data Device ID Type Type Registry
This document creates a new registry called 'Additional Call Data
Device ID Type'. As defined in [RFC5226], this registry operates
under "Expert Review" rules. The expert should ascertain that the
proposed type is well understood, and provides the information useful
to PSAPs and responders to uniquely identify a device.
The content of this registry includes:
Name: enumeration token of the device id type.
Description: Short description identifying type of device id.
The values defined are:
+--------+----------------------------------------+
| Name | Description |
+--------+----------------------------------------+
| MEID | Mobile Equipment Identifier (CDMA) |
| ESN | Electronic Serial Number(GSM) |
| MAC | Media Access Control Address (IEEE) |
| WiMAX | device certificate unique id |
| IMEI | International Mobile Equipment ID (GSM)|
| UDI | Unique Device Identifier (medical) |
| RFID | Radio Frequency Identification |
| SN | Manufacturer Serial Number |
+--------+----------------------------------------+
14.1.6. Device/Service Specific Additional Data Type Registry
This document creates a new registry called 'Device/Service Specific
Additional Data Type Registry'. As defined in [RFC5226], this
registry operates under "Expert Review" and "Specification Required"
rules. The expert should ascertain that the proposed type is well
understood, and provides information useful to PSAPs and responders.
The specification must contain a complete description of the data,
and a precise format specification suitable to allow interoperable
implementations.
The content of this registry includes:
Name: enumeration token of the data type.
Description: Short description identifying the the data.
Specification: Citation for the specification of the data.
Rosen, et al. Expires November 06, 2013 [Page 42]
Internet-Draft Additional Call Data May 2013
The values defined are:
+---------+----------------------------------------+----------------+
| Name | description | specification |
+---------+-------+--------------------------------+----------------+
| IEE1512 | Common Incident Management Message Set | IEEE 1512-2006 |
+---------+----------------------------------------+----------------+
| VEDS | Vehicle Emergency Data Set | APCO/NENA VEDS |
+---------+----------------------------------------+----------------+
14.1.7. Additional Call Data Blocks Registry
This document creates a new subregistry called 'Additional Call Data
Blocks' in the purpose registry established by RFC 261. As defined
in [RFC5226], this registry operates under "Expert Review" and
"Specification Required" rules. The expert is responsible for
verifying that the document contains a complete and clear
specification of the block and the block does not obviously duplicate
existing blocks.
The content of this registry includes:
Name: Element Name of enclosing block.
Reference: The document that describes the block
The values defined are:
+-------------+-----------+
| Name | Reference |
+-------------+-----------+
|ProviderInfo | RFCXXXX |
| SvcInfo | RFCXXXX |
| DevInfo | RFCXXXX |
| Subscriber | RFCXXXX |
| Comment | RFCXXXX |
+-------------+-----------+
RFC Editor Note:
replace XXXX in the table above with this documents RFC number
14.2. 'emergencyCallData' Purpose Parameter Value
This document defines the 'emergencyCall' value for the "purpose"
parameter of the Call-Info header field. The Call-Info header and
the corresponding registry for the 'purpose' parameter was
established with RFC 3261 [RFC3261].
Rosen, et al. Expires November 06, 2013 [Page 43]
Internet-Draft Additional Call Data May 2013
Header Parameter New
Field Name Value Reference
---------- --------- ----------------- ---------
Call-Info purpose emergencyCall [This RFC]
14.3. URN Sub-Namespace Registration for provided-by Registry Entry
This section registers the namespace specified in Section 14.5.1 in
the provided-by registry established by RFC 4119, for usage within
the 'provided-by' element of a PIDF-LO.
14.3.1. Provided-By XML Schema
<?xml version="1.0"?>
<xs:schema
targetNamespace="urn:ietf:params:xml:ns:emergencyCallAddlData"
targetNamespace="urn:ietf:params:xml:ns:pidf:
geopriv10:emergencyCallData"
xmlns:xs="http://www.w3.org/2001/XMLSchema"
xmlns:ad="urn:ietf:params:xml:ns:pidf:geopriv10:emergencyCallData"
xmlns:xml="http://www.w3.org/XML/1998/namespace"
elementFormDefault="qualified" attributeFormDefault="unqualified">
<xs:import namespace="http://www.w3.org/XML/1998/namespace"
schemaLocation="http://www.w3.org/2001/xml.xsd"/>
<xs:simpleType name="iso3166a2">
<xs:restriction base="xs:token">
<xs:pattern value="[A-Z]{2}"/>
</xs:restriction>
</xs:simpleType>
<xs:element name="emergencyCallDataReference">
<xs:complexType>
<xs:sequence>
<xs:attribute name="ref"
type="xs:anyURI" use="required"/>
<xs:attribute name="purpose"
type="xs:string" use="required"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element name="emergencyCallDataValue">
<xs:attribute name="purpose"
Rosen, et al. Expires November 06, 2013 [Page 44]
Internet-Draft Additional Call Data May 2013
type="xs:string" use="required"/>
</xs:element>
</xs:schema>
Figure 11: Provided-By XML Schema
14.4. MIME Registrations
14.4.1. MIME Content-type Registration for 'application/
emergencyCall.ProviderInfo+xml'
This specification requests the registration of a new MIME type
according to the procedures of RFC 4288 [RFC4288] and guidelines in
RFC 3023 [RFC3023].
MIME media type name: application
MIME subtype name: emergencyCall.ProviderInfo+xml
Mandatory parameters: none
Optional parameters: charset
Indicates the character encoding of enclosed XML.
Encoding considerations:
Uses XML, which can employ 8-bit characters, depending on the
character encoding used. See Section 3.2 of RFC 3023 [RFC3023].
Security considerations:
This content type is designed to carry the data provider
information, which is a sub-category of additional data about an
emergency call.
Since this data contains personal information appropriate
precautions have to be taken to limit unauthorized access,
inappropriate disclosure to third parties, and eavesdropping of
this information. Please refer to Section 12 and Section 13 for
more information.
Interoperability considerations: None
Published specification: [TBD: This specification]
Rosen, et al. Expires November 06, 2013 [Page 45]
Internet-Draft Additional Call Data May 2013
Applications which use this media type: Emergency Services
Additional information:
Magic Number: None
File Extension: .xml
Macintosh file type code: 'TEXT'
Person and email address for further information: Hannes
Tschofenig, Hannes.Tschofenig@gmx.net
Intended usage: LIMITED USE
Author: This specification is a work item of the IETF ECRIT
working group, with mailing list address <ecrit@ietf.org>.
Change controller: The IESG <ietf@ietf.org>
14.4.2. MIME Content-type Registration for 'application/
emergencyCall.SvcInfo+xml'
This specification requests the registration of a new MIME type
according to the procedures of RFC 4288 [RFC4288] and guidelines in
RFC 3023 [RFC3023].
MIME media type name: application
MIME subtype name: emergencyCall.SvcInfo+xml
Mandatory parameters: none
Optional parameters: charset
Indicates the character encoding of enclosed XML.
Encoding considerations:
Uses XML, which can employ 8-bit characters, depending on the
character encoding used. See Section 3.2 of RFC 3023 [RFC3023].
Security considerations:
This content type is designed to carry the service information,
which is a sub-category of additional data about an emergency
call.
Rosen, et al. Expires November 06, 2013 [Page 46]
Internet-Draft Additional Call Data May 2013
Since this data contains personal information appropriate
precautions have to be taken to limit unauthorized access,
inappropriate disclosure to third parties, and eavesdropping of
this information. Please refer to Section 12 and Section 13 for
more information.
Interoperability considerations: None
Published specification: [TBD: This specification]
Applications which use this media type: Emergency Services
Additional information:
Magic Number: None
File Extension: .xml
Macintosh file type code: 'TEXT'
Person and email address for further information: Hannes
Tschofenig, Hannes.Tschofenig@gmx.net
Intended usage: LIMITED USE
Author: This specification is a work item of the IETF ECRIT
working group, with mailing list address <ecrit@ietf.org>.
Change controller: The IESG <ietf@ietf.org>
14.4.3. MIME Content-type Registration for 'application/
emergencyCall.DevInfo+xml'
This specification requests the registration of a new MIME type
according to the procedures of RFC 4288 [RFC4288] and guidelines in
RFC 3023 [RFC3023].
MIME media type name: application
MIME subtype name: emergencyCall.DevInfo+xml
Mandatory parameters: none
Optional parameters: charset
Indicates the character encoding of enclosed XML.
Rosen, et al. Expires November 06, 2013 [Page 47]
Internet-Draft Additional Call Data May 2013
Encoding considerations:
Uses XML, which can employ 8-bit characters, depending on the
character encoding used. See Section 3.2 of RFC 3023 [RFC3023].
Security considerations:
This content type is designed to carry the device information
information, which is a sub-category of additional data about an
emergency call.
Since this data contains personal information appropriate
precautions have to be taken to limit unauthorized access,
inappropriate disclosure to third parties, and eavesdropping of
this information. Please refer to Section 12 and Section 13 for
more information.
Interoperability considerations: None
Published specification: [TBD: This specification]
Applications which use this media type: Emergency Services
Additional information:
Magic Number: None
File Extension: .xml
Macintosh file type code: 'TEXT'
Person and email address for further information: Hannes
Tschofenig, Hannes.Tschofenig@gmx.net
Intended usage: LIMITED USE
Author: This specification is a work item of the IETF ECRIT
working group, with mailing list address <ecrit@ietf.org>.
Change controller: The IESG <ietf@ietf.org>
Rosen, et al. Expires November 06, 2013 [Page 48]
Internet-Draft Additional Call Data May 2013
14.4.4. MIME Content-type Registration for 'application/
emergencyCall.SubInfo+xml'
This specification requests the registration of a new MIME type
according to the procedures of RFC 4288 [RFC4288] and guidelines in
RFC 3023 [RFC3023].
MIME media type name: application
MIME subtype name: emergencyCall.SubInfo+xml
Mandatory parameters: none
Optional parameters: charset
Indicates the character encoding of enclosed XML.
Encoding considerations:
Uses XML, which can employ 8-bit characters, depending on the
character encoding used. See Section 3.2 of RFC 3023 [RFC3023].
Security considerations:
This content type is designed to carry owner/subscriber
information, which is a sub-category of additional data about an
emergency call.
Since this data contains personal information appropriate
precautions have to be taken to limit unauthorized access,
inappropriate disclosure to third parties, and eavesdropping of
this information. Please refer to Section 12 and Section 13 for
more information.
Interoperability considerations: None
Published specification: [TBD: This specification]
Applications which use this media type: Emergency Services
Additional information:
Magic Number: None
File Extension: .xml
Macintosh file type code: 'TEXT'
Rosen, et al. Expires November 06, 2013 [Page 49]
Internet-Draft Additional Call Data May 2013
Person and email address for further information: Hannes
Tschofenig, Hannes.Tschofenig@gmx.net
Intended usage: LIMITED USE
Author: This specification is a work item of the IETF ECRIT
working group, with mailing list address <ecrit@ietf.org>.
Change controller: The IESG <ietf@ietf.org>
14.4.5. MIME Content-type Registration for 'application/
emergencyCall.Comment+xml'
This specification requests the registration of a new MIME type
according to the procedures of RFC 4288 [RFC4288] and guidelines in
RFC 3023 [RFC3023].
MIME media type name: application
MIME subtype name: emergencyCall.Comment+xml
Mandatory parameters: none
Optional parameters: charset
Indicates the character encoding of enclosed XML.
Encoding considerations:
Uses XML, which can employ 8-bit characters, depending on the
character encoding used. See Section 3.2 of RFC 3023 [RFC3023].
Security considerations:
This content type is designed to carry a comment, which is a sub-
category of additional data about an emergency call.
This data may contain personal information. Appropriate
precautions may have to be taken to limit unauthorized access,
inappropriate disclosure to third parties, and eavesdropping of
this information. Please refer to Section 12 and Section 13 for
more information.
Interoperability considerations: None
Published specification: [TBD: This specification]
Applications which use this media type: Emergency Services
Rosen, et al. Expires November 06, 2013 [Page 50]
Internet-Draft Additional Call Data May 2013
Additional information:
Magic Number: None
File Extension: .xml
Macintosh file type code: 'TEXT'
Person and email address for further information: Hannes
Tschofenig, Hannes.Tschofenig@gmx.net
Intended usage: LIMITED USE
Author: This specification is a work item of the IETF ECRIT
working group, with mailing list address <ecrit@ietf.org>.
Change controller: The IESG <ietf@ietf.org>
14.5. URN Sub-Namespace Registration
14.5.1. Registration for urn:ietf:params:xml:ns:emergencyCallAddlData
This section registers a new XML namespace, as per the guidelines in
RFC 3688 [RFC3688].
URI: urn:ietf:params:xml:ns:emergencyCallAddlData
Registrant Contact: IETF, ECRIT working group, <ecrit@ietf.org>, as
delegated by the IESG <iesg@ietf.org>.
XML:
BEGIN
<?xml version="1.0"?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML Basic 1.0//EN"
"http://www.w3.org/TR/xhtml-basic/xhtml-basic10.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="content-type"
content="text/html;charset=iso-8859-1"/>
<title>Namespace for Additional Emergency Call Data</title>
</head>
<body>
<h1>Namespace for Additional Data related to an Emergency Call</h1>
<p>See [TBD: This document].</p>
</body>
Rosen, et al. Expires November 06, 2013 [Page 51]
Internet-Draft Additional Call Data May 2013
</html>
END
14.5.2. Registration for
urn:ietf:params:xml:ns:emergencyCallProviderInfo
This section registers a new XML namespace, as per the guidelines in
RFC 3688 [RFC3688].
URI: urn:ietf:params:xml:ns:emergencyCallProviderInfo
Registrant Contact: IETF, ECRIT working group, <ecrit@ietf.org>, as
delegated by the IESG <iesg@ietf.org>.
XML:
BEGIN
<?xml version="1.0"?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML Basic 1.0//EN"
"http://www.w3.org/TR/xhtml-basic/xhtml-basic10.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="content-type"
content="text/html;charset=iso-8859-1"/>
<title>Namespace for Additional Emergency Call Data:
Data Provider Information</title>
</head>
<body>
<h1>Namespace for Additional Data related to an Emergency Call</h1>
<h2>Data Provider Information</h2>
<p>See [TBD: This document].</p>
</body>
</html>
END
14.5.3. Registration for urn:ietf:params:xml:ns:emergencyCall.SvcInfo
This section registers a new XML namespace, as per the guidelines in
RFC 3688 [RFC3688].
URI: urn:ietf:params:xml:ns:emergencyCall.SvcInfo
Rosen, et al. Expires November 06, 2013 [Page 52]
Internet-Draft Additional Call Data May 2013
Registrant Contact: IETF, ECRIT working group, <ecrit@ietf.org>, as
delegated by the IESG <iesg@ietf.org>.
XML:
BEGIN
<?xml version="1.0"?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML Basic 1.0//EN"
"http://www.w3.org/TR/xhtml-basic/xhtml-basic10.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="content-type"
content="text/html;charset=iso-8859-1"/>
<title>Namespace for Additional Emergency Call Data:
Service Information</title>
</head>
<body>
<h1>Namespace for Additional Data related to an Emergency Call</h1>
<h2>Service Information</h2>
<p>See [TBD: This document].</p>
</body>
</html>
END
14.5.4. Registration for urn:ietf:params:xml:ns:emergencyCall.DevInfo
This section registers a new XML namespace, as per the guidelines in
RFC 3688 [RFC3688].
URI: urn:ietf:params:xml:ns:emergencyCall.DevInfo
Registrant Contact: IETF, ECRIT working group, <ecrit@ietf.org>, as
delegated by the IESG <iesg@ietf.org>.
XML:
BEGIN
<?xml version="1.0"?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML Basic 1.0//EN"
"http://www.w3.org/TR/xhtml-basic/xhtml-basic10.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="content-type"
content="text/html;charset=iso-8859-1"/>
Rosen, et al. Expires November 06, 2013 [Page 53]
Internet-Draft Additional Call Data May 2013
<title>Namespace for Additional Emergency Call Data:
Device Information</title>
</head>
<body>
<h1>Namespace for Additional Data related to an Emergency Call</h1>
<h2>Device Information</h2>
<p>See [TBD: This document].</p>
</body>
</html>
END
14.5.5. Registration for urn:ietf:params:xml:ns:emergencyCall.SubInfo
This section registers a new XML namespace, as per the guidelines in
RFC 3688 [RFC3688].
URI: urn:ietf:params:xml:ns:emergencyCall.SubInfo
Registrant Contact: IETF, ECRIT working group, <ecrit@ietf.org>, as
delegated by the IESG <iesg@ietf.org>.
XML:
BEGIN
<?xml version="1.0"?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML Basic 1.0//EN"
"http://www.w3.org/TR/xhtml-basic/xhtml-basic10.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="content-type"
content="text/html;charset=iso-8859-1"/>
<title>Namespace for Additional Emergency Call Data:
Owner/Subscriber Information</title>
</head>
<body>
<h1>Namespace for Additional Data related to an Emergency Call</h1>
<h2> Owner/Subscriber Information</h2>
<p>See [TBD: This document].</p>
</body>
</html>
END
Rosen, et al. Expires November 06, 2013 [Page 54]
Internet-Draft Additional Call Data May 2013
14.5.6. Registration for urn:ietf:params:xml:ns:emergencyCall.Comment
This section registers a new XML namespace, as per the guidelines in
RFC 3688 [RFC3688].
URI: urn:ietf:params:xml:ns:emergencyCall.Comment
Registrant Contact: IETF, ECRIT working group, <ecrit@ietf.org>, as
delegated by the IESG <iesg@ietf.org>.
XML:
BEGIN
<?xml version="1.0"?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML Basic 1.0//EN"
"http://www.w3.org/TR/xhtml-basic/xhtml-basic10.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="content-type"
content="text/html;charset=iso-8859-1"/>
<title>Namespace for Additional Emergency Call Data:Comment</title>
</head>
<body>
<h1>Namespace for Additional Data related to an Emergency Call</h1>
<h2> Comment</h2>
<p>See [TBD: This document].</p>
</body>
</html>
END
14.6. Schema Registrations
This specification registers five schemas, as per the guidelines in
RFC 3688 [RFC3688].
URI: urn:ietf:params:xml:schema:additional-
data:emergencyCallProviderInfo
Registrant Contact: IETF, ECRIT Working Group (ecrit@ietf.org), as
delegated by the IESG (iesg@ietf.org).
XML: The XML schema can be found in Figure 1.
URI: urn:ietf:params:xml:schema:additional-data:addCallSvcInfo
Rosen, et al. Expires November 06, 2013 [Page 55]
Internet-Draft Additional Call Data May 2013
Registrant Contact: IETF, ECRIT Working Group (ectit@ietf.org), as
delegated by the IESG (iesg@ietf.org).
XML: The XML schema can be found in Figure 3.
URI: urn:ietf:params:xml:schema:additional-
data:emergencyCallDevInfo
Registrant Contact: IETF, ECRIT Working Group (ecrit@ietf.org), as
delegated by the IESG (iesg@ietf.org).
XML: The XML schema can be found in Figure 5.
URI: urn:ietf:params:xml:schema:additional-
data:emergencyCall.SubInfo
Registrant Contact: IETF, ECRIT Working Group (ecrit@ietf.org), as
delegated by the IESG (iesg@ietf.org).
XML: The XML schema can be found in Section 8.2.
URI: urn:ietf:params:xml:schema:additional-
data:emergencyCall.Comment
Registrant Contact: IETF, ECRIT Working Group (ecrit@ietf.org), as
delegated by the IESG (iesg@ietf.org).
XML: The XML schema can be found in Section 9.2.
14.7. VCard Parameter Value Registration
This document registers a new value in the vCARD Parameter Values
registry as defined by [RFC6350] with the following template:
Value: main
Purpose: The main telephone number, typically of an enterprise, as
opposed to a direct dial number of an individual employee
Conformance: This value can be used with the "TYPE" parameter
applied on the "TEL" property.
Example(s): TEL;VALUE=uri;TYPE="main,voice";PREF=1:tel:+1-418-656-90
00
15. Acknowledgments
Rosen, et al. Expires November 06, 2013 [Page 56]
Internet-Draft Additional Call Data May 2013
This work was originally started in NENA and has benefitted from a
large number of participants in NENA standardization efforts,
originally in the Long Term Definition Working Group, the Data
Technical Committee and most recently the Additional Data working
group. The authors are grateful for the initial work and extended
comments provided by the many NENA participants.
16. References
16.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2392] Levinson, E., "Content-ID and Message-ID Uniform Resource
Locators", RFC 2392, August 1998.
[RFC3023] Murata, M., St. Laurent, S., and D. Kohn, "XML Media
Types", RFC 3023, January 2001.
[RFC3261] Rosenberg, J., Schulzrinne, H., Camarillo, G., Johnston,
A., Peterson, J., Sparks, R., Handley, M., and E.
Schooler, "SIP: Session Initiation Protocol", RFC 3261,
June 2002.
[RFC3688] Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
January 2004.
[RFC4119] Peterson, J., "A Presence-based GEOPRIV Location Object
Format", RFC 4119, December 2005.
[RFC4288] Freed, N. and J. Klensin, "Media Type Specifications and
Registration Procedures", RFC 4288, December 2005.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.
[RFC6350] Perreault, S., "vCard Format Specification", RFC 6350,
August 2011.
[RFC6351] Perreault, S., "xCard: vCard XML Representation", RFC
6351, August 2011.
16.2. Informational References
[I-D.iab-privacy-considerations]
Rosen, et al. Expires November 06, 2013 [Page 57]
Internet-Draft Additional Call Data May 2013
Cooper, A., Tschofenig, H., Aboba, B., Peterson, J.,
Morris, J., Hansen, M., and R. Smith, "Privacy
Considerations for Internet Protocols", draft-iab-privacy-
considerations-03 (work in progress), July 2012.
[RFC5012] Schulzrinne, H. and R. Marshall, "Requirements for
Emergency Context Resolution with Internet Technologies",
RFC 5012, January 2008.
[RFC5222] Hardie, T., Newton, A., Schulzrinne, H., and H.
Tschofenig, "LoST: A Location-to-Service Translation
Protocol", RFC 5222, August 2008.
[RFC5985] Barnes, M., "HTTP-Enabled Location Delivery (HELD)", RFC
5985, September 2010.
[RFC6443] Rosen, B., Schulzrinne, H., Polk, J., and A. Newton,
"Framework for Emergency Calling Using Internet
Multimedia", RFC 6443, December 2011.
[RFC6881] Rosen, B. and J. Polk, "Best Current Practice for
Communications Services in Support of Emergency Calling",
BCP 181, RFC 6881, March 2013.
Appendix A. XML Schema for vCard/xCard
This section contains the vCard/xCard XML schema version of the Relax
NG schema defined in RFC 6351 [RFC6351] for simplified use with the
XML schemas defined in this document. The schema in RFC 6351
[RFC6351] is the normative source and this section is informative
only.
<?xml version="1.0" encoding="UTF-8"?>
<xs:schema xmlns:xs="http://www.w3.org/2001/XMLSchema"
elementFormDefault="qualified"
targetNamespace="urn:ietf:params:xml:ns:vcard-4.0"
xmlns:ns1="urn:ietf:params:xml:ns:vcard-4.0">
<!--
3.3
iana-token = xsd:string { pattern = "[a-zA-Z0-9-]+" }
x-name = xsd:string { pattern = "x-[a-zA-Z0-9-]+" }
-->
<xs:simpleType name="iana-token">
<xs:annotation>
<xs:documentation>vCard Format Specification
</xs:documentation>
Rosen, et al. Expires November 06, 2013 [Page 58]
Internet-Draft Additional Call Data May 2013
</xs:annotation>
<xs:restriction base="xs:string"/>
</xs:simpleType>
<xs:simpleType name="x-name">
<xs:restriction base="xs:string"/>
</xs:simpleType>
<!--
4.1
-->
<xs:element name="text" type="xs:string"/>
<xs:group name="value-text-list">
<xs:sequence>
<xs:element maxOccurs="unbounded" ref="ns1:text"/>
</xs:sequence>
</xs:group>
<!-- 4.2 -->
<xs:element name="uri" type="xs:anyURI"/>
<!-- 4.3.1 -->
<xs:element name="date"
substitutionGroup="ns1:value-date-and-or-time">
<xs:simpleType>
<xs:restriction base="xs:string">
<xs:pattern value="\d{8}|\d{4}-\d\d|
--\d\d(\d\d)?|---\d\d"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
<!-- 4.3.2 -->
<xs:element name="time"
substitutionGroup="ns1:value-date-and-or-time">
<xs:simpleType>
<xs:restriction base="xs:string">
<xs:pattern value="(\d\d(\d\d(\d\d)?)?|-\d\d(\d\d?)|--\d\d)
(Z|[+\-]\d\d(\d\d)?)?"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
<!-- 4.3.3 -->
<xs:element name="date-time"
substitutionGroup="ns1:value-date-and-or-time">
<xs:simpleType>
<xs:restriction base="xs:string">
<xs:pattern value=
"(\d{8}|--\d{4}|---\d\d)T
\d\d(\d\d(\d\d)?)?(Z|[+\-]\d\d(\d\d)?)?"/>
</xs:restriction>
</xs:simpleType>
Rosen, et al. Expires November 06, 2013 [Page 59]
Internet-Draft Additional Call Data May 2013
</xs:element>
<!-- 4.3.4 -->
<xs:element name="value-date-and-or-time" abstract="true"/>
<!-- 4.3.5 -->
<xs:complexType name="value-timestamp">
<xs:sequence>
<xs:element ref="ns1:timestamp"/>
</xs:sequence>
</xs:complexType>
<xs:element name="timestamp">
<xs:simpleType>
<xs:restriction base="xs:string">
<xs:pattern value="\d{8}T\d{6}(Z|[+\-]\d\d(\d\d)?)?"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
<!-- 4.4 -->
<xs:element name="boolean" type="xs:boolean"/>
<!-- 4.5 -->
<xs:element name="integer" type="xs:integer"/>
<!-- 4.6 -->
<xs:element name="float" type="xs:float"/>
<!-- 4.7 -->
<xs:element name="utc-offset">
<xs:simpleType>
<xs:restriction base="xs:string">
<xs:pattern value="[+\-]\d\d(\d\d)?"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
<!-- 4.8 -->
<xs:element name="language-tag">
<xs:simpleType>
<xs:restriction base="xs:string">
<xs:pattern
value="([a-z]{2,3}((-[a-z]{3}){0,3})?|[a-z]{4,8})
(-[a-z]{4})?(-([a-z]{2}|\d{3}))?(-([0-9a-z]{5,8}|
\d[0-9a-z]{3}))*(-[0-9a-wyz](-[0-9a-z]{2,8})+)*
(-x(-[0-9a-z]{1,8})+)?|x(-[0-9a-z]{1,8})+|[a-z]{1,3}
(-[0-9a-z]{2,8}){1,2}"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
<!--
5.1
-->
<xs:group name="param-language">
Rosen, et al. Expires November 06, 2013 [Page 60]
Internet-Draft Additional Call Data May 2013
<xs:annotation>
<xs:documentation>Section 5: Parameters</xs:documentation>
</xs:annotation>
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:language"/>
</xs:sequence>
</xs:group>
<xs:element name="language">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:language-tag"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.2 -->
<xs:group name="param-pref">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:pref"/>
</xs:sequence>
</xs:group>
<xs:element name="pref">
<xs:complexType>
<xs:sequence>
<xs:element name="integer">
<xs:simpleType>
<xs:restriction base="xs:integer">
<xs:minInclusive value="1"/>
<xs:maxInclusive value="100"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.4 -->
<xs:group name="param-altid">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:altid"/>
</xs:sequence>
</xs:group>
<xs:element name="altid">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.5 -->
Rosen, et al. Expires November 06, 2013 [Page 61]
Internet-Draft Additional Call Data May 2013
<xs:group name="param-pid">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:pid"/>
</xs:sequence>
</xs:group>
<xs:element name="pid">
<xs:complexType>
<xs:sequence>
<xs:element maxOccurs="unbounded" name="text">
<xs:simpleType>
<xs:restriction base="xs:string">
<xs:pattern value="\d+(\.\d+)?"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.6 -->
<xs:group name="param-type">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:type"/>
</xs:sequence>
</xs:group>
<xs:element name="type">
<xs:complexType>
<xs:sequence>
<xs:element maxOccurs="unbounded" name="text">
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="work"/>
<xs:enumeration value="home"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.7 -->
<xs:group name="param-mediatype">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:mediatype"/>
</xs:sequence>
</xs:group>
<xs:element name="mediatype">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:text"/>
Rosen, et al. Expires November 06, 2013 [Page 62]
Internet-Draft Additional Call Data May 2013
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.8 -->
<xs:group name="param-calscale">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:calscale"/>
</xs:sequence>
</xs:group>
<xs:element name="calscale">
<xs:complexType>
<xs:sequence>
<xs:element name="text">
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="gregorian"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.9 -->
<xs:group name="param-sort-as">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:sort-as"/>
</xs:sequence>
</xs:group>
<xs:element name="sort-as">
<xs:complexType>
<xs:sequence>
<xs:element maxOccurs="unbounded" ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 5.10 -->
<xs:group name="param-geo">
<xs:sequence>
<xs:element minOccurs="0" name="geo">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
</xs:sequence>
</xs:group>
<!-- 5.11 -->
Rosen, et al. Expires November 06, 2013 [Page 63]
Internet-Draft Additional Call Data May 2013
<xs:group name="param-tz">
<xs:sequence>
<xs:element minOccurs="0" name="tz">
<xs:complexType>
<xs:choice>
<xs:element ref="ns1:text"/>
<xs:element ref="ns1:uri"/>
</xs:choice>
</xs:complexType>
</xs:element>
</xs:sequence>
</xs:group>
<!--
6.1.3
-->
<xs:element name="source">
<xs:complexType>
<xs:sequence>
<xs:element name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.1.4 -->
<xs:element name="kind">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" maxOccurs="unbounded" name="text">
<xs:simpleType>
<xs:union memberTypes="ns1:x-name ns1:iana-token">
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="individual"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="group"/>
Rosen, et al. Expires November 06, 2013 [Page 64]
Internet-Draft Additional Call Data May 2013
</xs:restriction>
</xs:simpleType>
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="org"/>
</xs:restriction>
</xs:simpleType>
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="location"/>
</xs:restriction>
</xs:simpleType>
</xs:union>
</xs:simpleType>
</xs:element>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.2.1 -->
<xs:element name="fn">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.2.2 -->
<xs:element name="n">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-sort-as"/>
<xs:group ref="ns1:param-altid"/>
</xs:sequence>
Rosen, et al. Expires November 06, 2013 [Page 65]
Internet-Draft Additional Call Data May 2013
</xs:complexType>
</xs:element>
<xs:element maxOccurs="unbounded" ref="ns1:surname"/>
<xs:element maxOccurs="unbounded" ref="ns1:given"/>
<xs:element maxOccurs="unbounded" ref="ns1:additional"/>
<xs:element maxOccurs="unbounded" ref="ns1:prefix"/>
<xs:element maxOccurs="unbounded" ref="ns1:suffix"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element name="surname" type="xs:string"/>
<xs:element name="given" type="xs:string"/>
<xs:element name="additional" type="xs:string"/>
<xs:element name="prefix" type="xs:string"/>
<xs:element name="suffix" type="xs:string"/>
<!-- 6.2.3 -->
<xs:element name="nickname">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:group ref="ns1:value-text-list"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.2.4 -->
<xs:element name="photo">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
Rosen, et al. Expires November 06, 2013 [Page 66]
Internet-Draft Additional Call Data May 2013
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.2.5 -->
<xs:element name="bday">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-calscale"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:choice>
<xs:element ref="ns1:value-date-and-or-time"/>
<xs:element ref="ns1:text"/>
</xs:choice>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.2.6 -->
<xs:element name="anniversary">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-calscale"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:choice>
<xs:element ref="ns1:value-date-and-or-time"/>
<xs:element ref="ns1:text"/>
</xs:choice>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.2.7 -->
<xs:element name="gender">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:sex"/>
Rosen, et al. Expires November 06, 2013 [Page 67]
Internet-Draft Additional Call Data May 2013
<xs:element minOccurs="0" ref="ns1:identity"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element name="sex">
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value=""/>
<xs:enumeration value="M"/>
<xs:enumeration value="F"/>
<xs:enumeration value="O"/>
<xs:enumeration value="N"/>
<xs:enumeration value="U"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
<xs:element name="identity" type="xs:string"/>
<!-- 6.3.1 -->
<xs:group name="param-label">
<xs:sequence>
<xs:element minOccurs="0" ref="ns1:label"/>
</xs:sequence>
</xs:group>
<xs:element name="label">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element name="adr">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-geo"/>
<xs:group ref="ns1:param-tz"/>
<xs:group ref="ns1:param-label"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element maxOccurs="unbounded" ref="ns1:pobox"/>
Rosen, et al. Expires November 06, 2013 [Page 68]
Internet-Draft Additional Call Data May 2013
<xs:element maxOccurs="unbounded" ref="ns1:ext"/>
<xs:element maxOccurs="unbounded" ref="ns1:street"/>
<xs:element maxOccurs="unbounded" ref="ns1:locality"/>
<xs:element maxOccurs="unbounded" ref="ns1:region"/>
<xs:element maxOccurs="unbounded" ref="ns1:code"/>
<xs:element maxOccurs="unbounded" ref="ns1:country"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element name="pobox" type="xs:string"/>
<xs:element name="ext" type="xs:string"/>
<xs:element name="street" type="xs:string"/>
<xs:element name="locality" type="xs:string"/>
<xs:element name="region" type="xs:string"/>
<xs:element name="code" type="xs:string"/>
<xs:element name="country" type="xs:string"/>
<!-- 6.4.1 -->
<xs:element name="tel">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:element minOccurs="0" name="type">
<xs:complexType>
<xs:sequence>
<xs:element maxOccurs="unbounded" name="text">
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="work"/>
<xs:enumeration value="home"/>
<xs:enumeration value="text"/>
<xs:enumeration value="voice"/>
<xs:enumeration value="fax"/>
<xs:enumeration value="cell"/>
<xs:enumeration value="video"/>
<xs:enumeration value="pager"/>
<xs:enumeration value="textphone"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:group ref="ns1:param-mediatype"/>
Rosen, et al. Expires November 06, 2013 [Page 69]
Internet-Draft Additional Call Data May 2013
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:choice>
<xs:element ref="ns1:text"/>
<xs:element ref="ns1:uri"/>
</xs:choice>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.4.2 -->
<xs:element name="email">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.4.3 -->
<xs:element name="impp">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.4.4 -->
Rosen, et al. Expires November 06, 2013 [Page 70]
Internet-Draft Additional Call Data May 2013
<xs:element name="lang">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:language-tag"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.5.1 -->
<xs:group name="property-tz">
<xs:sequence>
<xs:element name="tz">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:choice>
<xs:element ref="ns1:text"/>
<xs:element ref="ns1:uri"/>
<xs:element ref="ns1:utc-offset"/>
</xs:choice>
</xs:sequence>
</xs:complexType>
</xs:element>
</xs:sequence>
</xs:group>
<!-- 6.5.2 -->
<xs:group name="property-geo">
<xs:sequence>
<xs:element name="geo">
Rosen, et al. Expires November 06, 2013 [Page 71]
Internet-Draft Additional Call Data May 2013
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
</xs:sequence>
</xs:group>
<!-- 6.6.1 -->
<xs:element name="title">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.6.2 -->
<xs:element name="role">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
Rosen, et al. Expires November 06, 2013 [Page 72]
Internet-Draft Additional Call Data May 2013
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.6.3 -->
<xs:element name="logo">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.6.4 -->
<xs:element name="org">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-sort-as"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:group ref="ns1:value-text-list"/>
</xs:sequence>
</xs:complexType>
Rosen, et al. Expires November 06, 2013 [Page 73]
Internet-Draft Additional Call Data May 2013
</xs:element>
<!-- 6.6.5 -->
<xs:element name="member">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.6.6 -->
<xs:element name="related">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:element minOccurs="0" name="type">
<xs:complexType>
<xs:sequence>
<xs:element maxOccurs="unbounded" name="text">
<xs:simpleType>
<xs:restriction base="xs:token">
<xs:enumeration value="work"/>
<xs:enumeration value="home"/>
<xs:enumeration value="contact"/>
<xs:enumeration value="acquaintance"/>
<xs:enumeration value="friend"/>
<xs:enumeration value="met"/>
<xs:enumeration value="co-worker"/>
<xs:enumeration value="colleague"/>
<xs:enumeration value="co-resident"/>
<xs:enumeration value="neighbor"/>
<xs:enumeration value="child"/>
<xs:enumeration value="parent"/>
<xs:enumeration value="sibling"/>
Rosen, et al. Expires November 06, 2013 [Page 74]
Internet-Draft Additional Call Data May 2013
<xs:enumeration value="spouse"/>
<xs:enumeration value="kin"/>
<xs:enumeration value="muse"/>
<xs:enumeration value="crush"/>
<xs:enumeration value="date"/>
<xs:enumeration value="sweetheart"/>
<xs:enumeration value="me"/>
<xs:enumeration value="agent"/>
<xs:enumeration value="emergency"/>
</xs:restriction>
</xs:simpleType>
</xs:element>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:choice>
<xs:element ref="ns1:uri"/>
<xs:element ref="ns1:text"/>
</xs:choice>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.7.1 -->
<xs:element name="categories">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:group ref="ns1:value-text-list"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.7.2 -->
<xs:element name="note">
<xs:complexType>
<xs:sequence>
Rosen, et al. Expires November 06, 2013 [Page 75]
Internet-Draft Additional Call Data May 2013
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.7.3 -->
<xs:element name="prodid">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:text"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.7.4 -->
<xs:element name="rev" type="ns1:value-timestamp"/>
<!-- 6.7.5 -->
<xs:element name="sound">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-language"/>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.7.6 -->
<xs:element name="uid">
<xs:complexType>
Rosen, et al. Expires November 06, 2013 [Page 76]
Internet-Draft Additional Call Data May 2013
<xs:sequence>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.7.7 -->
<xs:element name="clientpidmap">
<xs:complexType>
<xs:sequence>
<xs:element ref="ns1:sourceid"/>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element name="sourceid" type="xs:positiveInteger"/>
<!-- 6.7.8 -->
<xs:element name="url">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.8.1 -->
<xs:element name="key">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
Rosen, et al. Expires November 06, 2013 [Page 77]
Internet-Draft Additional Call Data May 2013
</xs:element>
<xs:choice>
<xs:element ref="ns1:uri"/>
<xs:element ref="ns1:text"/>
</xs:choice>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.9.1 -->
<xs:element name="fburl">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.9.2 -->
<xs:element name="caladruri">
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- 6.9.3 -->
<xs:element name="caluri">
Rosen, et al. Expires November 06, 2013 [Page 78]
Internet-Draft Additional Call Data May 2013
<xs:complexType>
<xs:sequence>
<xs:element minOccurs="0" name="parameters">
<xs:complexType>
<xs:sequence>
<xs:group ref="ns1:param-altid"/>
<xs:group ref="ns1:param-pid"/>
<xs:group ref="ns1:param-pref"/>
<xs:group ref="ns1:param-type"/>
<xs:group ref="ns1:param-mediatype"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:element ref="ns1:uri"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<!-- Top-level grammar -->
<xs:group name="property">
<xs:choice>
<xs:element ref="ns1:adr"/>
<xs:element ref="ns1:anniversary"/>
<xs:element ref="ns1:bday"/>
<xs:element ref="ns1:caladruri"/>
<xs:element ref="ns1:caluri"/>
<xs:element ref="ns1:categories"/>
<xs:element ref="ns1:clientpidmap"/>
<xs:element ref="ns1:email"/>
<xs:element ref="ns1:fburl"/>
<xs:element ref="ns1:fn"/>
<xs:group ref="ns1:property-geo"/>
<xs:element ref="ns1:impp"/>
<xs:element ref="ns1:key"/>
<xs:element ref="ns1:kind"/>
<xs:element ref="ns1:lang"/>
<xs:element ref="ns1:logo"/>
<xs:element ref="ns1:member"/>
<xs:element ref="ns1:n"/>
<xs:element ref="ns1:nickname"/>
<xs:element ref="ns1:note"/>
<xs:element ref="ns1:org"/>
<xs:element ref="ns1:photo"/>
<xs:element ref="ns1:prodid"/>
<xs:element ref="ns1:related"/>
<xs:element ref="ns1:rev"/>
<xs:element ref="ns1:role"/>
<xs:element ref="ns1:gender"/>
<xs:element ref="ns1:sound"/>
Rosen, et al. Expires November 06, 2013 [Page 79]
Internet-Draft Additional Call Data May 2013
<xs:element ref="ns1:source"/>
<xs:element ref="ns1:tel"/>
<xs:element ref="ns1:title"/>
<xs:group ref="ns1:property-tz"/>
<xs:element ref="ns1:uid"/>
<xs:element ref="ns1:url"/>
</xs:choice>
</xs:group>
<xs:element name="vcards">
<xs:complexType>
<xs:sequence>
<xs:element maxOccurs="unbounded" ref="ns1:vcard"/>
</xs:sequence>
</xs:complexType>
</xs:element>
<xs:complexType name="vcardType">
<xs:complexContent>
<xs:restriction base="xs:anyType">
<xs:choice maxOccurs="unbounded">
<xs:group ref="ns1:property"/>
<xs:element ref="ns1:group"/>
</xs:choice>
</xs:restriction>
</xs:complexContent>
</xs:complexType>
<xs:element name="vcard" type="ns1:vcardType"/>
<xs:element name="group">
<xs:complexType>
<xs:group minOccurs="0" maxOccurs="unbounded"
ref="ns1:property"/>
<xs:attribute name="name" use="required"/>
</xs:complexType>
</xs:element>
</xs:schema>
Authors' Addresses
Rosen, et al. Expires November 06, 2013 [Page 80]
Internet-Draft Additional Call Data May 2013
Brian Rosen
NeuStar
470 Conrad Dr.
Mars, PA 16046
US
Phone: +1 724 382 1051
Email: br@brianrosen.net
Hannes Tschofenig
Nokia Siemens Networks
Linnoitustie 6
Espoo 02600
Finland
Phone: +358 (50) 4871445
Email: Hannes.Tschofenig@gmx.net
URI: http://www.tschofenig.priv.at
Roger Marshall
TeleCommunication Systems, Inc.
2401 Elliott Avenue
Seattle, WA 98121
US
Phone: +1 206 792 2424
Email: rmarshall@telecomsys.com
URI: http://www.telecomsys.com
Randall Gellens
Qualcomm Technologies, Inc.
5775 Morehouse Drive
San Diego, CA 92121
US
Email: rg+ietf@qti.qualcomm.com
Rosen, et al. Expires November 06, 2013 [Page 81]