Skip to main content

A YANG Data Model for Layer 1 Types
draft-ietf-ccamp-layer1-types-03

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft whose latest revision state is "Active".
Authors Haomian Zheng , Italo Busi
Last updated 2019-11-02 (Latest revision 2019-09-09)
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Associated WG milestone
Jul 2022
Submit YANG model of Layer 1 Types to IESG for review
Document shepherd (None)
IESG IESG state I-D Exists
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-ccamp-layer1-types-03
CCAMP Working Group                                             H. Zheng
Internet-Draft                                                   I. Busi
Intended status: Standards Track                     Huawei Technologies
Expires: May 4, 2020                                    November 1, 2019

                  A YANG Data Model for Layer 1 Types
                    draft-ietf-ccamp-layer1-types-03

Abstract

   This document defines a collection of common data types and groupings
   in YANG data modeling language for layer 1 networks.  These derived
   common types and groupings are intended to be imported by modules
   that specifies the OTN networks, including the topology, tunnel,
   client signal adaptation and service.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on May 4, 2020.

Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Zheng & Busi               Expires May 4, 2020                  [Page 1]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Terminology and Notations . . . . . . . . . . . . . . . . . .   2
   3.  Prefix in Data Node Names . . . . . . . . . . . . . . . . . .   3
   4.  Layer 1 Types Overview  . . . . . . . . . . . . . . . . . . .   3
     4.1.  Relationship with other Modules . . . . . . . . . . . . .   3
     4.2.  Content in Layer 1 Type Module  . . . . . . . . . . . . .   3
     4.3.  Usage of groupings in Layer1-types  . . . . . . . . . . .   5
   5.  YANG Code for Layer1 Types  . . . . . . . . . . . . . . . . .   6
   6.  Security Considerations . . . . . . . . . . . . . . . . . . .  20
   7.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  20
   8.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  21
   9.  Contributors  . . . . . . . . . . . . . . . . . . . . . . . .  21
   10. References  . . . . . . . . . . . . . . . . . . . . . . . . .  22
     10.1.  Normative References . . . . . . . . . . . . . . . . . .  22
     10.2.  Informative References . . . . . . . . . . . . . . . . .  23
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  24

1.  Introduction

   This document introduces a collection of common data types which
   would be used in Layer 1 networks.  The derived types and groupings
   are designed to be the common types applicable for modeling Traffic
   Engineering (TE) features for Layer 1 optical networks.

   Typical L1 network, the Optical Transport Networking, was specified
   in [RFC7062].  Corresponding routing and signaling protocol have been
   specified in [RFC7138] and [RFC7139].  The types and groupings
   defined in this document is consistent to these document, and will be
   imported in other Layer 1 data models, including but not restrictive
   to, [I-D.ietf-ccamp-otn-topo-yang], [I-D.ietf-ccamp-otn-tunnel-model]
   and [I-D.ietf-ccamp-l1csm-yang].

   The data model in this draft has only types defined including
   groupings, typedef and identities.  There is no need to include
   configuration and state data according to the new Network Management
   Datastore Architecture [RFC8342].  The content in this draft is in
   consistent with [MEF63].

2.  Terminology and Notations

   Refer to [RFC7062] for the key terms used in this document, and the
   terminology for describing YANG data models can be found in
   [RFC7950].

Zheng & Busi               Expires May 4, 2020                  [Page 2]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

3.  Prefix in Data Node Names

   In this document, names of data nodes and other data model objects
   are prefixed using the standard prefix associated with the
   corresponding YANG imported modules.

      +-------------+---------------------------+----------------------+
      | Prefix      | YANG module               | Reference            |
      +-------------+---------------------------+----------------------+
      | layer1-types| ietf-layer1-types         | This Document        |
      +-------------+---------------------------+----------------------+

4.  Layer 1 Types Overview

4.1.  Relationship with other Modules

   This document defines one YANG module for common Layer 1 types.  The
   objective is to specifies common Layer 1 TE types that can be
   imported by layer 1 specific technology, for example OTN, in its
   technology-specific modules such as topology and tunnels.  It is
   worth noting that the generic traffic-engineering (TE) types module
   is specified in [I-D.ietf-teas-yang-te-types] as ietf-te-types, and
   both the module ietf-te-types and ietf-layer1-types are needed to be
   imported when the OTN is configured.

4.2.  Content in Layer 1 Type Module

   The module ietf-layer1-types contains the following YANG reusable
   types and groupings:

   tributary-slot-granularity:

   This is to define the granularity of the server layer ODU Link (HO
   ODUk or ODUCn) supporting a client layer ODU LSP (LO ODUj or ODUk,
   respectively).  Three granularities, 1.25G/2.5G/5G, have been
   specified.

   odu-type:

   This is to specify the type of ODUk LSP.

   client-signal:

   This is to specify the client signal types of OTN networks.  The
   initial input was the G-PID specified in [RFC7139].  Identities about

Zheng & Busi               Expires May 4, 2020                  [Page 3]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

   a few categories of client signal types, including ETH, STM-n, OC and
   Fiber Channel have been specified.

   otn-label-range-type:

   The label range type of OTN has two different representations,
   tributary slots (TS) and tributary port number (TPN), according to
   [RFC7139].  Respective representation is specified under this same
   base type.

   otn-link-bandwidth:

   This grouping defines the link bandwidth information and could be
   used in OTN topology model for bandwidth representation.  All the
   bandwidth related sections in generic topology module, ietf-te-
   topology, need to be augmented with this grouping for the usage of
   Layer 1.

   otn-path-bandwidth:

   This grouping defines the path bandwidth information and could be
   used in OTN topology model for bandwidth representation.  All the
   bandwidth related sections in generic topology module, ietf-te-
   topology, need to be augmented with this grouping for the usage of
   Layer 1.  This grouping is also applicable to set up the OTN tunnel.

   otn-label-restriction and otn-label-step:

   These groupings are used for the augmentation of OTN label in a
   specific way.

   otn-label-start-end and otn-label-hop:

   These groupings are used for the augmentation of label for OTN link
   and path respectively.

   optical-interface-func:

   The optical interface function is specified in [MEF63].  This
   grouping describes the functionality which encodes bits for
   transmission and the corresponding decode upon reception.

   service-performance-metric:

   The service performance metric is a quantitative characterization of
   Layer 1 characteristic information delivery quality experienced by
   the Layer 1 subscriber.

Zheng & Busi               Expires May 4, 2020                  [Page 4]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

4.3.  Usage of groupings in Layer1-types

   As described in [RFC7139], the OTN label usually represents the
   Tributary Port Number (TPN) and the related set of Tributary Slots
   (TS) assigned to a client layer ODU LSP (LO ODUj or ODUk) on a given
   server layer ODU (HO-ODU or ODUCn, respectively) Link (e.g., ODU2 LSP
   over ODU3 Link).  Some special OTN label values are also defined for
   an ODUk LSP being setup over an OTUk Link.

   The same OTN label shall be assigned to the same ODUk LSP at the two
   ends of an OTN Link.

   As described in [RFC7139], TPN can be a number from 1 to 4095 and TS
   are numbered from 1 to 4095, although the actual maximum values
   depend on the type of server layer ODU.  For example, a server layer
   ODU4 provides 80 time slots (numbered from 1 to 80) and the TPN
   values can be any number from 1 to 80.

   The OTN Label Range represents the values for the TPN and TS that are
   available for ODUk LSPs to be setup over a given OTN Link.

   The OTN Label Range is defined by the label-restriction list, defined
   in [I-D.ietf-teas-yang-te-types], which, for OTN, should be augmented
   using the otn-label-restriction grouping.

   Each entry in the label-restriction list represents either the range
   of the available TPN values or the range of the available TS values:
   the range-type attribute defines the type of range for each entry of
   the list.

   Each entry of the label-restriction list, as defined in
   [I-D.ietf-teas-yang-te-types], defines a label-start, a label-end, a
   label-step and a range-bitmap.  The label-start and label-end
   definitions for OTN should be augmented using the otn-link-label
   grouping.  The label-step definition for OTN should be augmented
   using the otn-label-step grouping.  It is expected that the otn-
   label-step will always be equal to its default value (i.e., 1).

   As described in [RFC7139], in some cases, the TPN assignment rules is
   flexible (e.g., ODU4 Link) while in other cases the TPN assignment
   rules are fixed (e.g., ODU1 Link).  In the latter case, only the TS
   range is reported: not reporting the TPN range means that the TPN
   shall be set equal to the TS number assigned to the ODUk LSP.

   As described in [RFC7139], in some cases, the TPN assignment rules
   depends on the TS Granularity (e.g., ODU2 or ODU3 Links).  Different
   entries in the label-restriction list will report different TPN

Zheng & Busi               Expires May 4, 2020                  [Page 5]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

   ranges for each TS granularity supported by the link, as indicated by
   the tsg attribute.

   As described in [RFC7139], in some cases, the TPN ranges are
   different for different types of ODUk LSPs.  For example, on an ODU2
   Link with 1,25G TS granularity, there is TPN range 1-4 for ODU1 and
   another TPN range 1-8 in common for ODU0 and ODUflex.  Different
   entries in the label-restriction list will report different TPN
   ranges for different set of ODUk types, as indicated by the odu-type-
   list .

5.  YANG Code for Layer1 Types

<CODE BEGINS>file "ietf-layer1-types@2019-11-01.yang"
module ietf-layer1-types {
  namespace "urn:ietf:params:xml:ns:yang:ietf-layer1-types";
  prefix "layer1-types";

  organization
    "IETF CCAMP Working Group";
  contact
    "WG Web: <http://tools.ietf.org/wg/ccamp/>
     WG List: <mailto:ccamp@ietf.org>

     Editor: Haomian Zheng
             <mailto:zhenghaomian@huawei.com>

     Editor: Italo Busi
       <mailto:Italo.Busi@huawei.com>";

  description
    "This module defines Layer 1 types. The model fully conforms
     to the Network Management Datastore Architecture (NMDA).

     Copyright (c) 2018 IETF Trust and the persons
     identified as authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Simplified BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (https://trustee.ietf.org/license-info).
     This version of this YANG module is part of RFC XXXX; see
     the RFC itself for full legal notices.";

  revision "2019-11-01" {

Zheng & Busi               Expires May 4, 2020                  [Page 6]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

    description
      "Initial Version";
    reference
      "RFC XXXX: A YANG Data Model for Layer 1 Types";
    // RFC Ed.: replace XXXX with actual RFC number, update date
    // information and remove this note
  }

  identity tributary-slot-granularity {
    description
      "Tributary slot granularity";
    reference
      "G.709/Y.1331, February 2016: Interfaces for the Optical
       Transport Network (OTN)";
  }

  identity tsg-1.25G {
    base tributary-slot-granularity;
    description
      "1.25G tributary slot granularity";
  }

  identity tsg-2.5G {
    base tributary-slot-granularity;
    description
      "2.5G tributary slot granularity";
  }

  identity tsg-5G {
    base tributary-slot-granularity;
    description
      "5G tributary slot granularity";
  }

  identity odu-type {
    description
      "Base identity for protocol framing used by tributary signals.";
  }

  identity ODU0 {
    base odu-type;
    description
      "ODU0 protocol (1.24G), RFC7139/ITU-T G.709, as standard track.";
  }

  identity ODU1 {
    base odu-type;
    description

Zheng & Busi               Expires May 4, 2020                  [Page 7]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

      "ODU1 protocol (2.49G), RFC7139/ITU-T G.709, as standard track.";
  }

  identity ODU1e {
    base odu-type;
    description
      "ODU1e protocol (10.35G), RFC7963/ITU-T G.sup43, as informational.";
  }

  identity ODU2 {
    base odu-type;
    description
      "ODU2 protocol (10.03G), RFC7139/ITU-T G.709, as standard track.";
  }

  identity ODU2e {
    base odu-type;
    description
      "ODU2e protocol (10.39G), RFC7139/ITU-T G.709, as standard track.";
  }

  identity ODU3 {
    base odu-type;
    description
      "ODU3 protocol (40.31G), RFC7139/ITU-T G.709, as standard track.";
  }

  identity ODU3e1 {
    base odu-type;
    description
      "ODU3e1 protocol (41.77G), RFC7963/ITU-T G.sup43, as informational.";
  }

  identity ODU3e2 {
    base odu-type;
    description
      "ODU3e2 protocol (41.78G), RFC7963/ITU-T G.sup43, as informational.";
  }

  identity ODU4 {
    base odu-type;
    description
      "ODU4 protocol (104.79G), RFC7139/ITU-T G.709, as standard track.";
  }

  identity ODUFlex-cbr {
    base odu-type;
    description

Zheng & Busi               Expires May 4, 2020                  [Page 8]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

      "ODU Flex CBR protocol for transporting constant bit rate
       signal";
  }

  identity ODUFlex-gfp {
    base odu-type;
    description
      "ODU Flex GFP protocol for transporting stream of packets
       using Generic Framing Procedure";
  }

  identity client-signal {
    description
      "Base identity from which specific client signals for the
       tunnel are derived";
  }

  identity ETH-1Gb {
    base client-signal;
    description
      "Client signal type of 1GbE";
  }

  identity ETH-10Gb-LAN {
    base client-signal;
    description
      "Client signal type of 10GbE LAN";
  }

  identity ETH-10Gb-WAN {
    base client-signal;
    description
      "Client signal type of 10GbE WAN";
  }

  identity ETH-40Gb {
    base client-signal;
    description
      "Client signal type of 40GbE";
  }

  identity ETH-100Gb {
    base client-signal;
    description
      "Client signal type of 100GbE";
  }

  identity STM-1 {

Zheng & Busi               Expires May 4, 2020                  [Page 9]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

    base client-signal;
    description
      "Client signal type of STM-1";
  }

  identity STM-4 {
    base client-signal;
    description
      "Client signal type of STM-4";
  }

  identity STM-16 {
    base client-signal;
    description
      "Client signal type of STM-16";
  }

  identity STM-64 {
    base client-signal;
    description
      "Client signal type of STM-64";
  }

  identity STM-256 {
    base client-signal;
    description
      "Client signal type of STM-256";
  }
  identity OC-3 {
    base client-signal;
    description
      "Client signal type of OC3";
  }

  identity OC-12 {
    base client-signal;
    description
      "Client signal type of OC12";
  }

  identity OC-48 {
    base client-signal;
    description
      "Client signal type of OC48";
  }

  identity OC-192 {
    base client-signal;

Zheng & Busi               Expires May 4, 2020                 [Page 10]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

    description
      "Client signal type of OC192";
  }

  identity OC-768 {
    base client-signal;
    description
      "Client signal type of OC768";
  }

  identity FC-100 {
    base client-signal;
    description
      "Client signal type of Fibre Channel FC-100";
  }

  identity FC-200 {
    base client-signal;
    description
      "Client signal type of Fibre Channel FC-200";
  }

  identity FC-400 {
    base client-signal;
    description
      "Client signal type of Fibre Channel FC-400";
  }

  identity FC-800 {
    base client-signal;
    description
      "Client signal type of Fibre Channel FC-800";
  }

  identity FC-1200 {
    base client-signal;
    description
      "Client signal type of Fibre Channel FC-1200";
  }

  identity FC-1600 {
    base client-signal;
    description
      "Client signal type of Fibre Channel FC-1600";
  }

  identity FC-3200 {
    base client-signal;

Zheng & Busi               Expires May 4, 2020                 [Page 11]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

    description
      "Client signal type of Fibre Channel FC-3200";
  }

  identity FICON-4G {
    base client-signal;
    description
      "Client signal type of Fibre Connection 4G";
  }

  identity FICON-8G {
    base client-signal;
    description
      "Client signal type of Fibre Connection 8G";
  }

  identity otn-label-range-type {
    description
      "Base identity from which specific OTN label
           range types derived";
  }

  identity label-range-trib-slot {
    base otn-label-range-type;
    description
      "Defines a range of OTN tributary slots";
  }

  identity label-range-trib-port {
    base otn-label-range-type;
    description
      "Defines a range of OTN tributary ports";
  }

  grouping otn-link-bandwidth {
    description "link bandwidth attributes for OTN";
    list odulist {
      key "odu-type";
      description
        "OTN bandwidth definition";
      leaf odu-type {
        type identityref {
          base layer1-types:odu-type;
        }
        description "ODU type";
      }
      leaf number {
        type uint16;

Zheng & Busi               Expires May 4, 2020                 [Page 12]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

        description "Number of ODUs";
      }
    }
  }

  grouping otn-path-bandwidth {
    description
          "path bandwidth attributes for OTN";
    leaf odu-type {
      type identityref {
        base layer1-types:odu-type;
      }
      description "ODU type";
    }
  }

  grouping otn-label-range-info {
    description "label range information for OTN";
    leaf range-type {
      type identityref {
        base layer1-types:otn-label-range-type;
      }
      description "type for range";
    }
    leaf tsg {
      type identityref {
        base layer1-types:tributary-slot-granularity;
      }
      description
            "Tributary slot granularity.";
      reference
        "G.709/Y.1331, February 2016: Interfaces for the
         Optical Transport Network (OTN)";
    }
        leaf-list odu-type-list {
      type identityref {
        base odu-type;
      }
      description
            "List of ODU types to which the label range applies.
                Empty odu-type-list means all the ODU types are applicable
                per label range. ";
    }
    leaf priority {
      type uint8;
      description "priority.";
    }
  }

Zheng & Busi               Expires May 4, 2020                 [Page 13]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

  grouping otn-label-start-end {
    description
          "The OTN label-start or label-end used to specify an OTN label range.";
    choice otn-label-type {
      description
        "OTN label range type, either TPN range or TS range";
      case tributary-port {
        leaf tpn {
          type uint16 {
            range "1..4095";
          }
          description
            "Tributary Port Number. Applicable in case of mux services.";
          reference
            "RFC7139: GMPLS Signaling Extensions for Control of Evolving
             G.709 Optical Transport Networks.";
        }
      }
      case tributary-slot {
        leaf ts {
          type uint16 {
            range "1..4095";
          }
          description
            "Tributary Slot Number. Applicable in case of mux services.";
          reference
            "RFC7139: GMPLS Signaling Extensions for Control of Evolving
             G.709 Optical Transport Networks.";
        }
      }
    }
  }

  grouping otn-label-hop {
    description "label information for OTN, for label-hop";
    leaf tpn {
      type uint16 {
        range "1..4095";
      }
      description
        "Tributary Port Number. Applicable in case of mux services.";
      reference
        "RFC7139: GMPLS Signaling Extensions for Control of Evolving
         G.709 Optical Transport Networks.";
    }
    leaf tsg {
      type identityref {
        base layer1-types:tributary-slot-granularity;

Zheng & Busi               Expires May 4, 2020                 [Page 14]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

      }
      description "Tributary slot granularity.";
      reference
        "G.709/Y.1331, February 2016: Interfaces for the
         Optical Transport Network (OTN)";
    }
    leaf ts-list {
      type string {
          pattern "([1-9][0-9]{0,3}(-[1-9][0-9]{0,3})?"
                + "(,[1-9][0-9]{0,3}(-[1-9][0-9]{0,3})?)*)";
        }
        description
          "A list of available tributary slots ranging
           between 1 and 4095.
           For example 1-20,25,50-1000";
        reference "RFC 7139: GMPLS Signaling Extensions for Control
                   of Evolving G.709 Optical Transport Networks";
    }
  }

  grouping otn-label-step {
    description "Label step for OTN";
    choice otn-label-type {
      description
        "OTN label range type, either TPN range or TS range";
      case tributary-port {
        leaf tpn {
          type uint16 {
            range "1..4095";
          }
          default 1;
          description
            "Label step which represents possible increments for
             Tributary Port Number.";
          reference
            "RFC7139: GMPLS Signaling Extensions for Control of Evolving
             G.709 Optical Transport Networks.";
        }
      }
      case tributary-slot {
        leaf ts {
          type uint16 {
            range "1..4095";
          }
          default 1;
          description
            "Label step which represents possible increments for
             Tributary Slot Number.";

Zheng & Busi               Expires May 4, 2020                 [Page 15]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

          reference
            "RFC7139: GMPLS Signaling Extensions for Control of Evolving
             G.709 Optical Transport Networks.";
        }
      }
    }
  }

  identity coding-func {
      description
      "base identity from which coding func is derived.";
     }

      identity ETH-1000X-PCS-36 {
         base "coding-func";
         description
            "PCS clause 36 coding function that corresponds to
             1000BASE-X";
         reference "MEF63 & IEEE802.3";
      }

      identity ETH-10GW-PCS-49-WIS-50 {
         base "coding-func";
         description
            "PCS clause 49 and WIS clause 50 coding func that
             corresponds to 10GBASE-W (WAN PHY)";
         reference "MEF63 & IEEE802.3";
      }

      identity ETH-10GR-PCS-49 {
         base "coding-func";
         description
            "PCS clause 49 coding function that corresponds to
             10GBASE-R (LAN PHY)";
         reference "MEF63 & IEEE802.3";
      }

      identity ETH-40GR-PCS-82 {
         base "coding-func";
         description
            "PCS clause 82 coding function that corresponds to
             40GBASE-R";
         reference "MEF63 & IEEE802.3";
      }

      identity ETH-100GR-PCS-82 {
         base "coding-func";
         description

Zheng & Busi               Expires May 4, 2020                 [Page 16]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

            "PCS clause 82 coding function that corresponds to
             100GBASE-R";
         reference "MEF63 & IEEE802.3";
      }

  identity optical-interface-func {
      description
        "base identity from which optical-interface-function is
         derived.";
     }

      identity SX-PMD-clause-38 {
         base "optical-interface-func";
         description
            "SX-PMD-clause-38 Optical Interface function for
            1000BASE-X PCS-36";
         reference "MEF63 & IEEE802.3";
      }

      identity LX-PMD-clause-38 {
         base "optical-interface-func";
         description
            "LX-PMD-clause-38 Optical Interface function for
            1000BASE-X PCS-36";
         reference "MEF63 & IEEE802.3";
      }

      identity LX10-PMD-clause-59 {
         base "optical-interface-func";
         description
            "LX10-PMD-clause-59 Optical Interface function for
            1000BASE-X PCS-36";
         reference "MEF63 & IEEE802.3";
      }

      identity BX10-PMD-clause-59 {
         base "optical-interface-func";
         description
            "BX10-PMD-clause-59 Optical Interface function for
            1000BASE-X PCS-36";
         reference "MEF63 & IEEE802.3";
      }

      identity LW-PMD-clause-52 {
         base "optical-interface-func";
         description
            "LW-PMD-clause-52 Optical Interface function for
            10GBASE-W PCS-49-WIS-50";

Zheng & Busi               Expires May 4, 2020                 [Page 17]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

         reference "MEF63 & IEEE802.3";
      }

      identity EW-PMD-clause-52 {
         base "optical-interface-func";
         description
            "EW-PMD-clause-52 Optical Interface function for
            10GBASE-W PCS-49-WIS-50";
         reference "MEF63 & IEEE802.3";
      }

      identity LR-PMD-clause-52 {
         base "optical-interface-func";
         description
            "LR-PMD-clause-52 Optical Interface function for
            10GBASE-R PCS-49";
         reference "MEF63 & IEEE802.3";
      }

      identity ER-PMD-clause-52 {
         base "optical-interface-func";
         description
            "ER-PMD-clause-52 Optical Interface function for
            10GBASE-R PCS-49";
         reference "MEF63 & IEEE802.3";
      }

      identity LR4-PMD-clause-87 {
         base "optical-interface-func";
         description
            "LR4-PMD-clause-87 Optical Interface function for
            40GBASE-R PCS-82";
         reference "MEF63 & IEEE802.3";
      }

      identity ER4-PMD-clause-87 {
         base "optical-interface-func";
         description
            "ER4-PMD-clause-87 Optical Interface function for
            40GBASE-R PCS-82";
         reference "MEF63 & IEEE802.3";
      }

      identity FR-PMD-clause-89 {
         base "optical-interface-func";
         description
            "FR-PMD-clause-89 Optical Interface function for
            40GBASE-R PCS-82";

Zheng & Busi               Expires May 4, 2020                 [Page 18]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

         reference "MEF63 & IEEE802.3";
      }

      identity LR4-PMD-clause-88 {
         base "optical-interface-func";
         description
            "LR4-PMD-clause-88 Optical Interface function for
            100GBASE-R PCS-82";
         reference "MEF63 & IEEE802.3";
      }

      identity ER4-PMD-clause-88 {
         base "optical-interface-func";
         description
            "ER4-PMD-clause-88 Optical Interface function for
            100GBASE-R PCS-82";
         reference "MEF63 & IEEE802.3";
      }

   identity service-performance-metric {
      description
            "list of service-specific performance metric";
     }

      identity One-way-Delay {
         base "service-performance-metric";
         description "one-way-delay";
      }

      identity One-way-Errored-Second {
         base "service-performance-metric";
         description "one-way-errored-second";
      }

      identity One-way-Severely-Errored-Second {
         base "service-performance-metric";
         description "one-way-severely-errored-second";
      }

      identity One-way-Unavailable-Second {
         base "service-performance-metric";
         description "one-way-unavailable-second";
      }

      identity One-way-Availability {
         base "service-performance-metric";
         description "one-way-availability";
      }

Zheng & Busi               Expires May 4, 2020                 [Page 19]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

      identity network-performance-metric {
        description "list of network-specific performance metric";
      }

}
<CODE ENDS>

6.  Security Considerations

   The YANG module specified in this document defines a schema for data
   that is designed to be accessed via network management protocols such
   as NETCONF [RFC6241] or RESTCONF [RFC8040].  The lowest NETCONF layer
   is the secure transport layer, and the mandatory-to-implement secure
   transport is Secure Shell (SSH) [RFC6242].  The lowest RESTCONF layer
   is HTTPS, and the mandatory-to-implement secure transport is TLS
   [RFC8446].

   The NETCONF access control model [RFC8341] provides the means to
   restrict access for particular NETCONF or RESTCONF users to a
   preconfigured subset of all available NETCONF or RESTCONF protocol
   operations and content.

   The YANG module in this document defines layer 1 type definitions
   (i.e., typedef, identity and grouping statements) in YANG data
   modeling language to be imported and used by other layer 1
   technology-specific modules.  When imported and used, the resultant
   schema will have data nodes that can be writable, or readable.  The
   access to such data nodes may be onsidered sensitive or vulnerable in
   some network environments.  Write operations (e.g., edit-config) to
   these data nodes without proper protection can have a negative effect
   on network operations.

   The security considerations spelled out in the YANG 1.1 specification
   [RFC7950] apply for this document as well.

7.  IANA Considerations

   It is proposed that IANA should assign new URIs from the "IETF XML
   Registry" [RFC3688] as follows:

         URI: urn:ietf:params:xml:ns:yang:ietf-layer1-types
         Registrant Contact: The IESG
         XML: N/A; the requested URI is an XML namespace.

Zheng & Busi               Expires May 4, 2020                 [Page 20]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

   This document registers following YANG modules in the YANG Module
   Names registry [RFC7950].

      name:         ietf-layer1-types
      namespace:    urn:ietf:params:xml:ns:yang:ietf-otn-types
      prefix:       layer1-types
      reference:    RFC XXXX

8.  Acknowledgements

   TBD.

9.  Contributors

   Dieter Beller
   Nokia
   Email: dieter.beller@nokia.com

   Sergio Belotti
   Nokia
   Email: sergio.belotti@nokia.com

   Yanlei Zheng
   China Unicom
   Email: zhengyl@dimpt.com

   Aihua Guo
   Huawei Technologies
   Email: aihuaguo@huawei.com

   Young Lee
   Huawei Technologies
   Email: leeyoung@huawei.com

   Lei Wang
   China Mobile
   Email: wangleiyj@chinamobile.com

   Oscar Gonzalez de Dios
   Telefonica
   Email: oscar.gonzalezdedios@telefonica.com

   Xufeng Liu
   Volta Networks
   Email: xufeng.liu.ietf@gmail.com

Zheng & Busi               Expires May 4, 2020                 [Page 21]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

   Yunbin Xu
   CAICT
   Email: xuyunbin@ritt.com

   Anurag Sharma
   Google
   Email: ansha@google.com

   Rajan Rao
   Infinera
   Email: rrao@infinera.com

   Victor Lopez
   Telefonica
   Email: victor.lopezalvarez@telefonica.com

   Yunbo Li
   China Mobile
   Email: liyunbo@chinamobile.com

10.  References

10.1.  Normative References

   [I-D.ietf-teas-yang-te-types]
              Saad, T., Gandhi, R., Liu, X., Beeram, V., and I. Bryskin,
              "Traffic Engineering Common YANG Types", draft-ietf-teas-
              yang-te-types-11 (work in progress), October 2019.

   [MEF63]    Metro Ethernet Forum, "Subscriber Layer1 Service
              Attributes Technical Specification", MEF 63, August 2018.

   [RFC3688]  Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688,
              DOI 10.17487/RFC3688, January 2004,
              <https://www.rfc-editor.org/info/rfc3688>.

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <https://www.rfc-editor.org/info/rfc6241>.

   [RFC6242]  Wasserman, M., "Using the NETCONF Protocol over Secure
              Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, June 2011,
              <https://www.rfc-editor.org/info/rfc6242>.

Zheng & Busi               Expires May 4, 2020                 [Page 22]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

   [RFC7139]  Zhang, F., Ed., Zhang, G., Belotti, S., Ceccarelli, D.,
              and K. Pithewan, "GMPLS Signaling Extensions for Control
              of Evolving G.709 Optical Transport Networks", RFC 7139,
              DOI 10.17487/RFC7139, March 2014,
              <https://www.rfc-editor.org/info/rfc7139>.

   [RFC7950]  Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language",
              RFC 7950, DOI 10.17487/RFC7950, August 2016,
              <https://www.rfc-editor.org/info/rfc7950>.

   [RFC8040]  Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", RFC 8040, DOI 10.17487/RFC8040, January 2017,
              <https://www.rfc-editor.org/info/rfc8040>.

   [RFC8341]  Bierman, A. and M. Bjorklund, "Network Configuration
              Access Control Model", STD 91, RFC 8341,
              DOI 10.17487/RFC8341, March 2018,
              <https://www.rfc-editor.org/info/rfc8341>.

   [RFC8342]  Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K.,
              and R. Wilton, "Network Management Datastore Architecture
              (NMDA)", RFC 8342, DOI 10.17487/RFC8342, March 2018,
              <https://www.rfc-editor.org/info/rfc8342>.

   [RFC8446]  Rescorla, E., "The Transport Layer Security (TLS) Protocol
              Version 1.3", RFC 8446, DOI 10.17487/RFC8446, August 2018,
              <https://www.rfc-editor.org/info/rfc8446>.

10.2.  Informative References

   [I-D.ietf-ccamp-l1csm-yang]
              Lee, Y., Lee, K., Zheng, H., Dhody, D., Dios, O., and D.
              Ceccarelli, "A YANG Data Model for L1 Connectivity Service
              Model (L1CSM)", draft-ietf-ccamp-l1csm-yang-10 (work in
              progress), September 2019.

   [I-D.ietf-ccamp-otn-topo-yang]
              Zheng, H., Guo, A., Busi, I., Sharma, A., Liu, X.,
              Belotti, S., Xu, Y., Wang, L., and O. Dios, "A YANG Data
              Model for Optical Transport Network Topology", draft-ietf-
              ccamp-otn-topo-yang-08 (work in progress), September 2019.

   [I-D.ietf-ccamp-otn-tunnel-model]
              Zheng, H., Busi, I., Belotti, S., Lopezalvarez, V., and Y.
              Xu, "OTN Tunnel YANG Model", draft-ietf-ccamp-otn-tunnel-
              model-08 (work in progress), October 2019.

Zheng & Busi               Expires May 4, 2020                 [Page 23]
Internet-Draft     A YANG Data Model for Layer 1 Types     November 2019

   [RFC7062]  Zhang, F., Ed., Li, D., Li, H., Belotti, S., and D.
              Ceccarelli, "Framework for GMPLS and PCE Control of G.709
              Optical Transport Networks", RFC 7062,
              DOI 10.17487/RFC7062, November 2013,
              <https://www.rfc-editor.org/info/rfc7062>.

   [RFC7138]  Ceccarelli, D., Ed., Zhang, F., Belotti, S., Rao, R., and
              J. Drake, "Traffic Engineering Extensions to OSPF for
              GMPLS Control of Evolving G.709 Optical Transport
              Networks", RFC 7138, DOI 10.17487/RFC7138, March 2014,
              <https://www.rfc-editor.org/info/rfc7138>.

Authors' Addresses

   Haomian Zheng
   Huawei Technologies
   H1-1-A043S Huawei Industrial Base, Songshanhu
   Dongguan, Guangdong  523808
   China

   Email: zhenghaomian@huawei.com

   Italo Busi
   Huawei Technologies
   Milan
   Italy

   Email: Italo.Busi@huawei.com

Zheng & Busi               Expires May 4, 2020                 [Page 24]