Skip to main content

Performance Measurement (PM) with Marking Method in Bit Index Explicit Replication (BIER) Layer
draft-ietf-bier-pmmm-oam-09

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft whose latest revision state is "Active".
Authors Greg Mirsky , Lianshu Zheng , Mach Chen , Giuseppe Fioccola
Last updated 2020-12-02 (Latest revision 2020-05-25)
Replaces draft-mirsky-bier-pmmm-oam
RFC stream Internet Engineering Task Force (IETF)
Formats
Additional resources Mailing list discussion
Stream WG state WG Document
Revised I-D Needed - Issue raised by AD
Document shepherd Suneesh Babu
Shepherd write-up Show Last changed 2019-05-29
IESG IESG state I-D Exists (IESG: Dead)
Consensus boilerplate Yes
Telechat date (None)
Responsible AD Alvaro Retana
Send notices to Suneesh Babu <suneeshbk@gmail.com>, aretana.ietf@gmail.com
draft-ietf-bier-pmmm-oam-09
BIER  Working Group                                            G. Mirsky
Internet-Draft                                                 ZTE Corp.
Intended status: Standards Track                                L. Zheng
Expires: June 5, 2021                                            M. Chen
                                                             G. Fioccola
                                                     Huawei Technologies
                                                        December 2, 2020

 Performance Measurement (PM) with Marking Method in Bit Index Explicit
                        Replication (BIER) Layer
                      draft-ietf-bier-pmmm-oam-09

Abstract

   This document describes the applicability of a hybrid performance
   measurement method for packet loss and packet delay measurements of a
   multicast service through a Bit Index Explicit Replication domain.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on June 5, 2021.

Copyright Notice

   Copyright (c) 2020 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of

Mirsky, et al.            Expires June 5, 2021                  [Page 1]
Internet-Draft       PM with Marking Method in BIER        December 2020

   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   2
   2.  Conventions used in this document . . . . . . . . . . . . . .   2
     2.1.  Terminology . . . . . . . . . . . . . . . . . . . . . . .   3
     2.2.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   3.  OAM Field in BIER Header  . . . . . . . . . . . . . . . . . .   3
   4.  Theory of Operation . . . . . . . . . . . . . . . . . . . . .   4
     4.1.  Single-Marking Enabled Measurement  . . . . . . . . . . .   5
     4.2.  Double-Marking Enabled Measurement  . . . . . . . . . . .   6
     4.3.  Operational Considerations  . . . . . . . . . . . . . . .   6
   5.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .   7
   6.  Security Considerations . . . . . . . . . . . . . . . . . . .   7
   7.  Acknowledgement . . . . . . . . . . . . . . . . . . . . . . .   7
   8.  References  . . . . . . . . . . . . . . . . . . . . . . . . .   7
     8.1.  Normative References  . . . . . . . . . . . . . . . . . .   8
     8.2.  Informative References  . . . . . . . . . . . . . . . . .   8
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .   9

1.  Introduction

   [RFC8279] introduces and explains the Bit Index Explicit Replication
   (BIER) architecture and how it supports the forwarding of multicast
   data packets.  [RFC8296] specified that in the case of BIER
   encapsulation in an MPLS network, a BIER-MPLS label, the label that
   is at the bottom of the label stack, uniquely identifies the
   multicast flow.  [RFC8321] describes a hybrid performance measurement
   method, according to the classification of measurement methods in
   [RFC7799].  The method, called Packet Network Performance Monitoring
   (PNPM), can be used to measure packet loss, latency, and jitter on
   live traffic complies with requirements #5 and #12 listed in
   [I-D.ietf-bier-oam-requirements].  Because this method is based on
   marking consecutive batches of packets, the method is often referred
   to as a marking method.  Terms PNPM and "marking method" in this
   document are used interchangeably.

   This document defines how the marking method can be used on the BIER
   layer to measure packet loss and delay metrics of a multicast flow in
   an MPLS network.

2.  Conventions used in this document

Mirsky, et al.            Expires June 5, 2021                  [Page 2]
Internet-Draft       PM with Marking Method in BIER        December 2020

2.1.  Terminology

   BFR: Bit-Forwarding Router

   BFER: Bit-Forwarding Egress Router

   BFIR: Bit-Forwarding Ingress Router

   BIER: Bit Index Explicit Replication

   OAM: Operations, Administration and Maintenance

   PNPM: Packet Network Performance Monitoring

2.2.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

3.  OAM Field in BIER Header

   [RFC8296] defined the two-bits long field, referred to as OAM.  The
   OAM field can be used for the marking performance measurement method.
   Because the setting of the field to any value does not affect
   forwarding and/or quality of service treatment of a packet, using the
   OAM field for PNPM in BIER layer can be viewed as the example of the
   hybrid performance measurement method.

   Figure 1 displays the interpretation of the OAM field defined in this
   specification for the use of the PNPM method.  The context of
   interpretation of the OAM field MAY be signaled via the control plane
   or configured using an extension to the BIER YANG data model
   [I-D.ietf-bier-bier-yang].  These extensions are outside the scope of
   this document.

     0
     0   1
   +-+-+-+-+
   | S | D |
   +-+-+-+-+

                 Figure 1: OAM field of BIER Header format

   where:

Mirsky, et al.            Expires June 5, 2021                  [Page 3]
Internet-Draft       PM with Marking Method in BIER        December 2020

   o  S - Single-Marking flag;

   o  D - Double-Marking flag.

4.  Theory of Operation

   The marking method can be used in the multicast environment supported
   by BIER layer.  Without limiting any generality consider multicast
   network presented in Figure 2.  Any combination of markings can be
   applied to a multicast flow by the Bit Forwarding Ingress Router
   (BFIR) at either ingress or egress point to perform node, link,
   segment or end-to-end measurement to detect performance degradation
   defect and localize it efficiently.

                           -----
                         --| D |
                 -----  /  -----
               --| B |--
              /  -----  \  -----
             /           --| E |
   -----    /              -----
   | A |---                -----
   -----    \            --| F |
             \  -----   /  -----
              --| C |--
                -----   \  -----
                         --| G |
                           -----

                        Figure 2: Multicast network

   Using the marking method, a BFIR creates distinct sub-flows in the
   particular multicast traffic over BIER layer.  Each sub-flow consists
   of consecutive blocks of identically marked packets.  For example, a
   block of N packets, with each packet being marked as X, is followed
   by the block of M packets with each packet being marked as Y.  These
   blocks are unambiguously recognizable by a monitoring point at any
   Bit Forwarding Router (BFR) and can be measured to calculate packet
   loss and/or packet delay metrics.  The marking method can be used on
   multiple flows concurently.  Demultiplexing of monitored flows might
   be achived using n-tuple, for example, two-tuple as combination of
   the values in the Entropy and BFIR-id fields [RFC8296].  Also, that
   can be achieved by using an explicit Flow Identifiier.  The
   definition of the Flow Identifier is outside the scope of this
   specification.  It is expected that the marking values be set and
   cleared at the edge of BIER domain.  Thus for the scenario presented

Mirsky, et al.            Expires June 5, 2021                  [Page 4]
Internet-Draft       PM with Marking Method in BIER        December 2020

   in Figure 2 if the operator initially monitors the A-C-G and A-B-D
   segments he may enable measurements on segments C-F and B-E at any
   time.

4.1.  Single-Marking Enabled Measurement

   As explained in [RFC8321], marking can be applied to delineate blocks
   of packets based either on the equal number of packets in a block or
   based on the equal time interval.  The latter method offers better
   control as it allows a better account for capabilities of downstream
   nodes to report statistics related to batches of packets and, at the
   same time, time resolution that affects defect detection interval.

   If the Single-Marking measurement is used to measure packet loss,
   then the D flag MUST be set to zero on transmit and ignored by the
   monitoring point.

   The S flag is used to create sub-flows to measure the packet loss by
   switching the value of the S flag every N-th packet or at certain
   time intervals.  Delay metrics MAY be calculated with the sub-flow
   using any of the following methods:

   o  First/Last Packet Delay calculation: whenever the marking, i.e.,
      the value of S flag changes, a BFR can store the timestamp of the
      first/last packet of the block.  The timestamp can be compared
      with the timestamp of the packet that arrived in the same order
      through a monitoring point at a downstream BFR to compute packet
      delay.  Because timestamps collected based on the order of arrival
      this method is sensitive to packet loss and re-ordering of packets
      (see Section 4.3 for more details).

   o  Average Packet Delay calculation: an average delay is calculated
      by considering the average arrival time of the packets within a
      single block.  A BFR may collect timestamps for each packet
      received within a single block.  Average of the timestamp is the
      sum of all the timestamps divided by the total number of packets
      received.  Then the difference between the average packet arrival
      time calculated for the downstream monitoring point and the same
      metric but calculated at the upstream monitoring point is the
      average packet delay on the segment between these two points.
      This method is robust to out of order packets and also to packet
      loss on the segment between the measurement points (packet loss
      may cause a minor loss of accuracy in the calculated metric
      because the number of packets used is different at each
      measurement point).  This method only provides a single metric for
      the duration of the block, and it doesn't give the minimum and
      maximum delay values.  This limitation of producing only the
      single metric could be overcome by reducing the duration of the

Mirsky, et al.            Expires June 5, 2021                  [Page 5]
Internet-Draft       PM with Marking Method in BIER        December 2020

      block.  As a result, the calculated value of the average delay
      will better reflect the minimum and maximum delay values of the
      block's duration time.

4.2.  Double-Marking Enabled Measurement

   Double-Marking method allows measurement of minimum and maximum
   delays for the monitored flow, but it requires more nodal and network
   resources.  If the Double-Marking method used, then the S flag is
   used to create the sub-flow, i.e., mark blocks of packets.  The D
   flag is used to mark single packets within a block to measure delay
   and jitter.

   The first marking (S flag alternation) is needed for packet loss and
   also for average delay measurement.  The second marking (D flag is
   put to one) creates a new set of marked packets that are fully
   identified over the BIER network, so that a BFR can store the
   timestamps of these packets; these timestamps can be compared with
   the timestamps of the same packets on a second BFR to compute packet
   delay values for each packet.  The number of measurements can be
   easily increased by changing the frequency of the second marking.  On
   the other hand, the higher frequency of the second marking will cause
   a higher volume of the measurement data being transported through the
   BIER domain.  An operator should consider and balance both effects.
   This method is useful to measure not only the average delay but also
   the minimum and maximum delay values and, in wider terms, to know
   more about the statistic distribution of delay values.

4.3.  Operational Considerations

   For the ease of operational procedures, the initial marking of a
   multicast flow is performed at BFIR. and cleared, by way of removing
   BIER encapsulation form a payload packet, at the edge of the BIER
   domain by BFERs.

   Since at the time of writing this specification, there are no
   proposals to using auto-discovery or signaling mechanism to inform
   downstream nodes what methodology is used each monitoring point MUST
   be configured beforehand.

   Section 4.3 [RFC8321] provides a detailed analysis of how packet re-
   ordering and the duration of the block in the Single-Marking mode of
   the marking method impact the accuracy of the packet loss
   measurement.  Re-ordering of packets in the Single-Marking mode will
   be noticeable only at the edge of a block of packets (re-ordering
   within the block cannot be detected in the Single-Marking mode).  If
   the extra delay for some packets is much smaller than half of the
   duration of a block, then it should be easier to attribute re-ordered

Mirsky, et al.            Expires June 5, 2021                  [Page 6]
Internet-Draft       PM with Marking Method in BIER        December 2020

   packets to the proper block and thus maintain the accuracy of the
   packet loss measurement.

   Selection of a time interval to switch the marking of a batch of
   packets should be based on the service requirements.  In the course
   of the regular operation, reports, including performance metrics like
   packet loss ratio, packet delay, and inter-packet delay variation,
   are logged every 15 minutes.  Thus, it is reasonable to maintain the
   duration of the measurement interval at 5 minutes with 100
   measurements per each interval.  To support these measurements,
   marking of the packet batch is switched every 3 seconds.  In case
   when performance metrics are required in near-real-time, the duration
   interval of a single batch of identically marked packets will be in
   the range of tens of milliseconds.

5.  IANA Considerations

   This document sets no requirements to IANA.  This section can be
   removed before the publication.

6.  Security Considerations

   Regarding using the marking method, [RFC8321] stressed two types of
   security concerns.  First, the potential harm caused by the
   measurements, is a lesser threat as [RFC8296] defines OAM field used
   by the marking method so that the value of "two bits have no effect
   on the path taken by a BIER packet and have no effect on the quality
   of service applied to a BIER packet."  Second security concern,
   potential harm to the measurements can be mitigated by using policy,
   suggested in [RFC8296], to accept BIER packets only from trusted
   routers, not from customer-facing interfaces.

   All the security considerations for BIER discussed in [RFC8296] are
   inherited by this document.

7.  Acknowledgement

   Comments from Alvaro Retana helped improve the document and are much
   appreciated.

   Reviews and comments from Quan Xiong and Xiao Min are thankfully
   acknowledged.

8.  References

Mirsky, et al.            Expires June 5, 2021                  [Page 7]
Internet-Draft       PM with Marking Method in BIER        December 2020

8.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8296]  Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
              Tantsura, J., Aldrin, S., and I. Meilik, "Encapsulation
              for Bit Index Explicit Replication (BIER) in MPLS and Non-
              MPLS Networks", RFC 8296, DOI 10.17487/RFC8296, January
              2018, <https://www.rfc-editor.org/info/rfc8296>.

   [RFC8321]  Fioccola, G., Ed., Capello, A., Cociglio, M., Castaldelli,
              L., Chen, M., Zheng, L., Mirsky, G., and T. Mizrahi,
              "Alternate-Marking Method for Passive and Hybrid
              Performance Monitoring", RFC 8321, DOI 10.17487/RFC8321,
              January 2018, <https://www.rfc-editor.org/info/rfc8321>.

8.2.  Informative References

   [I-D.ietf-bier-bier-yang]
              Chen, R., hu, f., Zhang, Z., dai.xianxian@zte.com.cn, d.,
              and M. Sivakumar, "YANG Data Model for BIER Protocol",
              draft-ietf-bier-bier-yang-07 (work in progress), September
              2020.

   [I-D.ietf-bier-oam-requirements]
              Mirsky, G., Nainar, N., Chen, M., and S. Pallagatti,
              "Operations, Administration and Maintenance (OAM)
              Requirements for Bit Index Explicit Replication (BIER)
              Layer", draft-ietf-bier-oam-requirements-11 (work in
              progress), November 2020.

   [RFC7799]  Morton, A., "Active and Passive Metrics and Methods (with
              Hybrid Types In-Between)", RFC 7799, DOI 10.17487/RFC7799,
              May 2016, <https://www.rfc-editor.org/info/rfc7799>.

   [RFC8279]  Wijnands, IJ., Ed., Rosen, E., Ed., Dolganow, A.,
              Przygienda, T., and S. Aldrin, "Multicast Using Bit Index
              Explicit Replication (BIER)", RFC 8279,
              DOI 10.17487/RFC8279, November 2017,
              <https://www.rfc-editor.org/info/rfc8279>.

Mirsky, et al.            Expires June 5, 2021                  [Page 8]
Internet-Draft       PM with Marking Method in BIER        December 2020

Authors' Addresses

   Greg Mirsky
   ZTE Corp.

   Email: gregimirsky@gmail.com

   Lianshu Zheng
   Huawei Technologies

   Email: vero.zheng@huawei.com

   Mach Chen
   Huawei Technologies

   Email: mach.chen@huawei.com

   Giuseppe Fioccola
   Huawei Technologies

   Email: giuseppe.fioccola@huawei.com

Mirsky, et al.            Expires June 5, 2021                  [Page 9]