Skip to main content

Yang Data Model for Bidirectional Forwarding Detection (BFD)
draft-ietf-bfd-yang-05

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 9127.
Authors Reshad Rahman , Lianshu Zheng , Santosh Pallagatti , Mahesh Jethanandani , Greg Mirsky
Last updated 2017-03-10
Replaces draft-zheng-bfd-yang
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd (None)
IESG IESG state Became RFC 9127 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-bfd-yang-05
Network Working Group                                     R. Rahman, Ed.
Internet-Draft                                             Cisco Systems
Intended status: Standards Track                           L. Zheng, Ed.
Expires: September 11, 2017                          Huawei Technologies
                                                           S. Pallagatti

                                                         M. Jethanandani
                                                           Cisco Systems
                                                               G. Mirsky
                                                         ZTE Corporation
                                                          March 10, 2017

      Yang Data Model for Bidirectional Forwarding Detection (BFD)
                       draft-ietf-bfd-yang-05.txt

Abstract

   This document defines a YANG data model that can be used to configure
   and manage Bidirectional Forwarding Detection (BFD).

Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 11, 2017.

Rahman, et al.         Expires September 11, 2017               [Page 1]
Internet-Draft                  BFD Yang                      March 2017

Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Contributors  . . . . . . . . . . . . . . . . . . . . . .   4
   2.  Design of the Data Model  . . . . . . . . . . . . . . . . . .   4
     2.1.  Design of Configuration Model . . . . . . . . . . . . . .   4
       2.1.1.  Common BFD configuration parameters . . . . . . . . .   5
       2.1.2.  Single-hop IP . . . . . . . . . . . . . . . . . . . .   6
       2.1.3.  Multi-hop IP  . . . . . . . . . . . . . . . . . . . .   6
       2.1.4.  MPLS Traffic Engineering Tunnels  . . . . . . . . . .   7
       2.1.5.  MPLS Label Switched Paths . . . . . . . . . . . . . .   7
       2.1.6.  Link Aggregation Groups . . . . . . . . . . . . . . .   7
     2.2.  Design of Operational Model . . . . . . . . . . . . . . .   8
     2.3.  Notifications . . . . . . . . . . . . . . . . . . . . . .   8
     2.4.  RPC Operations  . . . . . . . . . . . . . . . . . . . . .   9
     2.5.  BFD top level hierarchy . . . . . . . . . . . . . . . . .   9
     2.6.  BFD IP single-hop hierarchy . . . . . . . . . . . . . . .   9
     2.7.  BFD IP multi-hop hierarchy  . . . . . . . . . . . . . . .  11
     2.8.  BFD over LAG hierarchy  . . . . . . . . . . . . . . . . .  13
     2.9.  BFD over MPLS LSPs hierarchy  . . . . . . . . . . . . . .  15
     2.10. BFD over MPLS-TE hierarchy  . . . . . . . . . . . . . . .  17
     2.11. Examples  . . . . . . . . . . . . . . . . . . . . . . . .  19
     2.12. Interaction with other YANG modules . . . . . . . . . . .  19
       2.12.1.  Module ietf-interfaces . . . . . . . . . . . . . . .  19
       2.12.2.  Module ietf-ip . . . . . . . . . . . . . . . . . . .  19
       2.12.3.  Module ietf-mpls . . . . . . . . . . . . . . . . . .  20
       2.12.4.  Module ietf-te . . . . . . . . . . . . . . . . . . .  20
     2.13. BFD top-level Yang Module . . . . . . . . . . . . . . . .  20
     2.14. BFD IP single-hop Yang Module . . . . . . . . . . . . . .  32
     2.15. BFD IP multi-hop Yang Module  . . . . . . . . . . . . . .  35
     2.16. BFD over LAG Yang Module  . . . . . . . . . . . . . . . .  38
     2.17. BFD over MPLS Yang Module . . . . . . . . . . . . . . . .  42
     2.18. BFD over MPLS-TE Yang Module  . . . . . . . . . . . . . .  45

Rahman, et al.         Expires September 11, 2017               [Page 2]
Internet-Draft                  BFD Yang                      March 2017

     2.19. Security Considerations . . . . . . . . . . . . . . . . .  48
     2.20. IANA Considerations . . . . . . . . . . . . . . . . . . .  48
     2.21. Acknowledgements  . . . . . . . . . . . . . . . . . . . .  48
   3.  References  . . . . . . . . . . . . . . . . . . . . . . . . .  49
     3.1.  Normative References  . . . . . . . . . . . . . . . . . .  49
     3.2.  Informative References  . . . . . . . . . . . . . . . . .  50
   Appendix A.  Change log . . . . . . . . . . . . . . . . . . . . .  51
     A.1.  Changes between versions -04 and -05  . . . . . . . . . .  51
     A.2.  Changes between versions -03 and -04  . . . . . . . . . .  52
     A.3.  Changes between versions -02 and -03  . . . . . . . . . .  52
     A.4.  Changes between versions -01 and -02  . . . . . . . . . .  52
     A.5.  Changes between versions -00 and -01  . . . . . . . . . .  52
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  52

1.  Introduction

   YANG [RFC6020] is a data definition language that was introduced to
   define the contents of a conceptual data store that allows networked
   devices to be managed using NETCONF [RFC6241].  YANG is proving
   relevant beyond its initial confines, as bindings to other interfaces
   (e.g RESTCONF [I-D.ietf-netconf-restconf]) and encodings other than
   XML (e.g JSON) are being defined.  Furthermore, YANG data models can
   be used as the basis of implementation for other interfaces, such as
   CLI and programmatic APIs.

   This document defines a YANG data model that can be used to configure
   and manage Bidirectional Forwarding Detection (BFD)[RFC5880].  BFD is
   a network protocol which is used for liveness detection of arbitrary
   paths between systems.  Some examples of different types of paths
   over which we have BFD:

   1) Two systems directly connected via IP.  This is known as BFD over
   single-hop IP [RFC5881]

   2) Two systems connected via multiple hops [RFC5883]

   3) Two systems connected via MPLS Label Switched Paths (LSPs)
   [RFC5884]

   4) Two systems connected via pseudowires (PWs), this is known as
   Virtual Circuit Connectivity Verification (VCCV) [RFC5885]

   5) Two systems connected via a Link Aggregation Group (LAG) interface
   [RFC7130]

   BFD typically does not operate on its own.  Various control
   protocols, also known as BFD clients, use the services provided by
   BFD for their own operation [RFC5882].  The obvious candidates which

Rahman, et al.         Expires September 11, 2017               [Page 3]
Internet-Draft                  BFD Yang                      March 2017

   use BFD are those which do not have Hellos to detect failures, e.g.
   static routes, and routing protocols whose Hellos do not support sub-
   second failure detection, e.g.  OSPF and IS-IS.

1.1.  Contributors

2.  Design of the Data Model

   Since BFD is used for liveliness detection of various forwarding
   paths, there is no uniform key to identify a BFD session.  So the BFD
   data model is split in multiple YANG modules where each module
   corresponds to one type of forwarding path.  For example, BFD for IP
   single-hop is in one YANG module and BFD for MPLS-TE is in another
   YANG module.  The main difference between these modules is how a BFD
   session is uniquely identified, i.e the key for the list containing
   the BFD sessions for that forwarding path.  To avoid duplication of
   BFD definitions, we have common types and groupings which are used by
   all the modules.

   A new control-plane protocol "bfdv1" is defined and a "bfd" container
   is created under control-plane-protocol as specified in [RFC8022].
   This new "bfd" node is augmented by all the YANG modules for their
   respective specific information.  Each BFD YANG module which augments
   the "bfd" node contains a "config" node and an "oper" node.

   BFD can operate in the following contexts:

   1.  Network devices as described in [I-D.ietf-rtgwg-device-model]

   2.  Logical Network Elements as described in
       [I-D.ietf-rtgwg-lne-model]

   3.  Network instances as described in [I-D.ietf-rtgwg-ni-model]

   The approach taken is to do a schema-mount (see
   [I-D.ietf-netmod-schema-mount]) of the BFD model in the appropriate
   locations.  For example, if an implementation supports BFD IP multi-
   hop in network instances, the implementation would do schema-mount of
   the BFD IP multi-hop model in a mount-point which resides in a
   network instance.

2.1.  Design of Configuration Model

   The configuration model consists mainly of the parameters specified
   in [RFC5880].  Some examples are desired minimum transmit interval,
   required minimum receive interval, detection multiplier, etc

Rahman, et al.         Expires September 11, 2017               [Page 4]
Internet-Draft                  BFD Yang                      March 2017

   Some implementations have BFD session configuration under the BFD
   clients.  For example, BFD session configuration is under routing
   applications such as OSPF, IS-IS, BGP etc.  Other implementations
   have BFD session configuration centralized under BFD, i.e. outside
   the multiple BFD clients.

   The BFD parameters of interest to a BFD client are mainly the
   multiplier and interval(s) since those parameters impact the
   convergence time of the BFD clients when a failure occurs.  Other
   parameters such as BFD authentication are not specific to the
   requirements of the BFD client.  To avoid splitting the BFD
   configuration between BFD clients and BFD, all the configuration is
   under BFD.  The only BFD configuration under BFD clients should be an
   "enable" knob which makes those clients react to BFD liveliness
   detection events.

2.1.1.  Common BFD configuration parameters

   The basic BFD configuration parameters are:

   local-multiplier
           This is the detection time multiplier as defined in
           [RFC5880].

   desired-min-tx-interval
           This is the Desired Min TX Interval as defined in [RFC5880].

   required-min-rx-interval
           This is the Required Min RX Interval as defined in [RFC5880].

   Although [RFC5880] allows for different values for transmit and
   receive intervals, some implementations allow users to specify just
   one interval which is used for both transmit and receive intervals or
   separate values for transmit and receive intervals.  The BFD YANG
   model supports this: there is a choice between "min-interval", used
   for both transmit and receive intervals, and "desired-min-tx-
   interval" and "required-min-rx-interval".  This is supported via a
   grouping which is used by the YANG modules for the various forwarding
   paths.  There are also intervals for the echo function (if
   supported):

   desired-min-echo-tx-interval
           This is the minimum interval that the local system would like
           to use when transmitting BFD echo packets.  If 0, the echo
           function as defined in [RFC5880] is disabled.

   required-min-echo-rx-interval

Rahman, et al.         Expires September 11, 2017               [Page 5]
Internet-Draft                  BFD Yang                      March 2017

           This is the Required Min Echo RX Interval as defined in
           [RFC5880].

   For BFD authentication we have:

   key-chain
           This is a reference to key-chain defined in
           [I-D.ietf-rtgwg-yang-key-chain].  The keys, cryptographic
           algotihms, key lifetime etc are all defined in the key-chain
           model.

   replay-protection
           This specifies meticulous v/s non-meticulous mode as per
           [RFC5880].

2.1.2.  Single-hop IP

   For single-hop IP, there is an augment of the "bfd" data node in
   Section 2.  We have a list of IP single-hop sessions where each
   session is uniquely identified by the interface and destination
   address pair.  For the configuration parameters we use what is
   defined in Section 2.1.1

2.1.3.  Multi-hop IP

   For multi-hop IP, there is an augment of the "bfd" data node in
   Section 2.

   We have a list for BFD sessions over multi-hop IP.  The key consists
   of:

   source address
           Address belonging to the local system as per [RFC5883]

   destination address
           Address belonging to the remote system as per [RFC5883]

   For the configuration parameters we use what is defined in
   Section 2.1.1

   Here are some extra parameters:

   tx-ttl
           TTL of outgoing BFD control packets.

   rx-ttl
           Minimum TTL of incoming BFD control packets.

Rahman, et al.         Expires September 11, 2017               [Page 6]
Internet-Draft                  BFD Yang                      March 2017

2.1.4.  MPLS Traffic Engineering Tunnels

   For MPLS-TE tunnels, BFD is configured under the MPLS-TE tunnel since
   the desired failure detection parameters is a property of the MPLS-TE
   tunnel.  This is achieved by augmenting the MPLS-TE data model in
   [I-D.ietf-teas-yang-te].  For BFD parameters which are specific to
   the TE application, e.g. whether to tear down the tunnel in the event
   of a BFD session failure, these parameters will be defined in the
   YANG model of the MPLS-TE application.

   On top of the usual BFD parameters, we have the following per MPLS-TE
   tunnel:

   encap
           Encapsulation for the BFD packets: choice between IP, G-ACh
           and IP with G-ACh as per [RFC5586]

   For general MPLS-TE data, "mpls-te" data node is added under the
   "bfd" node in Section 2.  Since some MPLS-TE tunnels are uni-
   directional there is no MPLS-TE configuration for these tunnels on
   the egress node (note that this does not apply to bi-directional
   MPLS-TP tunnels).  The BFD parameters for the egress node are added
   under "mpls-te".

2.1.5.  MPLS Label Switched Paths

   Here we address MPLS LSPs whose FEC is an IP address.  The "bfd" node
   in Section 2 is augmented with "mpls" which contains a list of
   sessions uniquely identified by an IP address.

   Since these LSPs are uni-directional there is no LSP configuration on
   the egress node.  The BFD parameters for the egress node are added
   under "mpls".

2.1.6.  Link Aggregation Groups

   Per [RFC7130], configuring BFD on LAG consists of having micro-BFD
   sessions on each LAG member link.  Since the BFD parameters are an
   attribute of the LAG, they should be under the LAG.  However there is
   no LAG YANG model which we can augment.  So a "lag" data node is
   added to the "bfd" node in Section 2, the configuration is per-LAG:
   we have a list of LAGs.  The destination IP address of the micro-BFD
   sessions is configured per-LAG and per address-family (IPv4 and IPv6)

Rahman, et al.         Expires September 11, 2017               [Page 7]
Internet-Draft                  BFD Yang                      March 2017

2.2.  Design of Operational Model

   The operational model contains both the overall statistics of BFD
   sessions running on the device and the per session operational
   information.

   The overall statistics of BFD sessions consist of number of BFD
   sessions, number of BFD sessions up etc.  This information is
   available globally (i.e. for all BFD sessions) under the "bfd" node
   in Section 2 and also per type of forwarding path.

   For each BFD session, mainly three categories of operational items
   are shown.  The fundamental information of a BFD session such as the
   local discriminator, remote discriminator and the capability of
   supporting demand detect mode are shown in the first category.  The
   second category includes a BFD session running information, e.g. the
   remote BFD state and the diagnostic code received.  Another example
   is the actual transmit interval between the control packets, which
   may be different from the desired minimum transmit interval
   configured, is shown in this category.  Similar examples are actual
   received interval between the control packets and the actual transmit
   interval between the echo packets.  The third category contains the
   detailed statistics of the session, e.g. when the session
   transitioned up/down and how long it has been in that state.

   For some session types, there may be more than 1 session on the
   virtual path to the destination.  For example, with IP multi-hop
   there could be multiple BFD sessions from the source to the same
   destination to test the various paths (ECMP) to the destination.
   Each of the BFD sessions on the same virtual path is uniquely
   identified by the local discriminator.

2.3.  Notifications

   This YANG model defines notifications to inform clients of BFD of
   important events detected during the protocol operation.  Pair of
   local and remote discriminator identifies a BFD session on local
   system.  Notifications also give more important details about BFD
   sessions; e.g. new state, time in previous state, network-instance
   and the reason that the BFD session state changed.  The notifications
   are defined for each type of forwarding path but use groupings for
   common information.

Rahman, et al.         Expires September 11, 2017               [Page 8]
Internet-Draft                  BFD Yang                      March 2017

2.4.  RPC Operations

   TBD

2.5.  BFD top level hierarchy

   At the "bfd" node under control-plane-protocol, there is no
   configuration data, only operational data.  The operational data
   consist of overall BFD session statistics, i.e. for BFD on all types
   of forwarding paths.  The "bfd" node under control-plane-protocol can
   be mounted in a network device (top-level), in an LNE or in a network
   instance.

   module: ietf-bfd
   augment /rt:routing/rt:control-plane-protocols
           /rt:control-plane-protocol:
      +--rw bfd
         +--rw config
         +--ro oper
            +--ro bfd-session-statistics
               +--ro session-count?              uint32
               +--ro session-up-count?           uint32
               +--ro session-down-count?         uint32
               +--ro session-admin-down-count?   uint32

2.6.  BFD IP single-hop hierarchy

   An "ip-sh" node is added under "bfd" node in control-plane-protocol.
   The configuration and operational data for each BFD IP single-hop
   session is under this "ip-sh" node.  The "ip-sh" node can be mounted
   in a network device (top-level), in an LNE or in a network instance.

   module: ietf-bfd-ip-sh
   augment /rt:routing/rt:control-plane-protocols
           /rt:control-plane-protocol/bfd:bfd:
      +--rw ip-sh
         +--rw config
         |  +--rw session-cfg
         |     +--rw sessions* [interface dest-addr]
         |        +--rw interface                       if:interface-ref
         |        +--rw dest-addr                       inet:ip-address
         |        +--rw source-addr?                    inet:ip-address
         |        +--rw local-multiplier?               bfd-multiplier
         |        +--rw (interval-config-type)?
         |        |  +--:(tx-rx-intervals)
         |        |  |  +--rw desired-min-tx-interval          uint32
         |        |  |  +--rw required-min-rx-interval         uint32
         |        |  +--:(single-interval)

Rahman, et al.         Expires September 11, 2017               [Page 9]
Internet-Draft                  BFD Yang                      March 2017

         |        |     +--rw min-interval                     uint32
         |        +--rw demand-enabled?                  boolean
         |        +--rw admin-down?                      boolean
         |        +--rw authentication-parms! {bfd-authentication}?
         |        |  +--rw key-chain?           kc:key-chain-ref
         |        |  +--rw replay-protection?   identityref
         |        +--rw desired-min-echo-tx-interval?    uint32
         |        +--rw required-min-echo-rx-interval?   uint32
         +--ro oper
            +--ro bfd-session-statistics
            |  +--ro session-count?              uint32
            |  +--ro session-up-count?           uint32
            |  +--ro session-down-count?         uint32
            |  +--ro session-admin-down-count?   uint32
            +--ro sessions* [interface dest-addr]
               +--ro interface               if:interface-ref
               +--ro dest-addr               inet:ip-address
               +--ro source-addr?            inet:ip-address
               +--ro path-type?              identityref
               +--ro local-discriminator?    bfd-discriminator
               +--ro remote-discriminator?   bfd-discriminator
               +--ro remote-multiplier?      bfd-multiplier
               +--ro out-interface?          if:interface-ref
               +--ro demand-capability?      boolean
               +--ro source-port?            inet:port-number
               +--ro dest-port?              inet:port-number
               +--ro session-running
               |  +--ro session-index?             uint32
               |  +--ro local-state?               bfd-state
               |  +--ro remote-state?              bfd-state
               |  +--ro local-diagnostic?          bfd-diagnostic
               |  +--ro remote-diagnostic?         bfd-diagnostic
               |  +--ro detection-mode?            enumeration
               |  +--ro negotiated-tx-interval?    uint32
               |  +--ro negotiated-rx-interval?    uint32
               |  +--ro echo-tx-interval-in-use?   uint32
               |  +--ro detection-time?            uint32
               +--ro sesssion-statistics
                  +--ro create-time?            yang:date-and-time
                  +--ro last-down-time?         yang:date-and-time
                  +--ro last-up-time?           yang:date-and-time
                  +--ro down-count?             uint32
                  +--ro admin-down-count?       uint32
                  +--ro receive-packet-count?   uint64
                  +--ro send-packet-count?      uint64
                  +--ro receive-bad-packet?     uint64
                  +--ro send-failed-packet?     uint64
   notifications:

Rahman, et al.         Expires September 11, 2017              [Page 10]
Internet-Draft                  BFD Yang                      March 2017

      +---n bfd-singlehop-notification
         +--ro local-discr?              bfd-discriminator
         +--ro remote-discr?             bfd-discriminator
         +--ro new-state?                bfd-state
         +--ro state-change-reason?      string
         +--ro time-in-previous-state?   string
         +--ro dest-addr?                inet:ip-address
         +--ro source-addr?              inet:ip-address
         +--ro session-index?            uint32
         +--ro path-type?                identityref
         +--ro interface?                if:interface-ref
         +--ro echo-enabled?             boolean

2.7.  BFD IP multi-hop hierarchy

   An "ip-mh" node is added under the "bfd" node in cntrol-plane-
   protocol.  The configuration and operational data for each BFD IP
   multi-hop session is under this "ip-mh" node.  In the operational
   model we support multiple BFD multi-hop sessions per remote address
   (ECMP), the local discriminator is used as key.  The "ip-mh" node can
   be mounted in a network device (top-level), in an LNE or in a network
   instance.

   module: ietf-bfd-ip-mh
   augment /rt:routing/rt:control-plane-protocols
           /rt:control-plane-protocol/bfd:bfd:
      +--rw ip-mh
         +--rw config
         |  +--rw session-cfg
         |     +--rw sessions* [source-addr dest-addr]
         |        +--rw source-addr                 inet:ip-address
         |        +--rw dest-addr                   inet:ip-address
         |        +--rw local-multiplier?           bfd-multiplier
         |        +--rw (interval-config-type)?
         |        |  +--:(tx-rx-intervals)
         |        |  |  +--rw desired-min-tx-interval     uint32
         |        |  |  +--rw required-min-rx-interval    uint32
         |        |  +--:(single-interval)
         |        |     +--rw min-interval                uint32
         |        +--rw demand-enabled?             boolean
         |        +--rw admin-down?                 boolean
         |        +--rw authentication-parms! {bfd-authentication}?
         |        |  +--rw key-chain?           kc:key-chain-ref
         |        |  +--rw replay-protection?   identityref
         |        +--rw tx-ttl?                     bfd:ttl
         |        +--rw rx-ttl                      bfd:ttl
         +--ro oper
            +--ro bfd-session-statistics

Rahman, et al.         Expires September 11, 2017              [Page 11]
Internet-Draft                  BFD Yang                      March 2017

            |  +--ro session-count?              uint32
            |  +--ro session-up-count?           uint32
            |  +--ro session-down-count?         uint32
            |  +--ro session-admin-down-count?   uint32
            +--ro session-group* [source-addr dest-addr]
               +--ro source-addr    inet:ip-address
               +--ro dest-addr      inet:ip-address
               +--ro sessions* [local-discriminator]
                  +--ro ttl?                    bfd:ttl
                  +--ro path-type?              identityref
                  +--ro local-discriminator     bfd-discriminator
                  +--ro remote-discriminator?   bfd-discriminator
                  +--ro remote-multiplier?      bfd-multiplier
                  +--ro out-interface?          if:interface-ref
                  +--ro demand-capability?      boolean
                  +--ro source-port?            inet:port-number
                  +--ro dest-port?              inet:port-number
                  +--ro session-running
                  |  +--ro session-index?             uint32
                  |  +--ro local-state?               bfd-state
                  |  +--ro remote-state?              bfd-state
                  |  +--ro local-diagnostic?          bfd-diagnostic
                  |  +--ro remote-diagnostic?         bfd-diagnostic
                  |  +--ro detection-mode?            enumeration
                  |  +--ro negotiated-tx-interval?    uint32
                  |  +--ro negotiated-rx-interval?    uint32
                  |  +--ro echo-tx-interval-in-use?   uint32
                  |  +--ro detection-time?            uint32
                  +--ro sesssion-statistics
                     +--ro create-time?            yang:date-and-time
                     +--ro last-down-time?         yang:date-and-time
                     +--ro last-up-time?           yang:date-and-time
                     +--ro down-count?             uint32
                     +--ro admin-down-count?       uint32
                     +--ro receive-packet-count?   uint64
                     +--ro send-packet-count?      uint64
                     +--ro receive-bad-packet?     uint64
                     +--ro send-failed-packet?     uint64
   notifications:
      +---n bfd-multihop-notification
         +--ro local-discr?              bfd-discriminator
         +--ro remote-discr?             bfd-discriminator
         +--ro new-state?                bfd-state
         +--ro state-change-reason?      string
         +--ro time-in-previous-state?   string
         +--ro dest-addr?                inet:ip-address
         +--ro source-addr?              inet:ip-address
         +--ro session-index?            uint32

Rahman, et al.         Expires September 11, 2017              [Page 12]
Internet-Draft                  BFD Yang                      March 2017

         +--ro path-type?                identityref

2.8.  BFD over LAG hierarchy

   A "lag" node is added under the "bfd" node in control-plane-protocol.
   The configuration and operational data for each BFD LAG session is
   under this "lag" node.  The "lag" node can be mounted in a network
   device (top-level), in an LNE or in a network instance.

   module: ietf-bfd-lag
   augment /rt:routing/rt:control-plane-protocols
           /rt:control-plane-protocol/bfd:bfd:
      +--rw lag
         +--rw config
         |  +--rw session-cfg
         |     +--rw sessions* [lag-name]
         |        +--rw lag-name                    if:interface-ref
         |        +--rw ipv4-dest-addr?             inet:ipv4-address
         |        +--rw ipv6-dest-addr?             inet:ipv6-address
         |        +--rw local-multiplier?           bfd-multiplier
         |        +--rw (interval-config-type)?
         |        |  +--:(tx-rx-intervals)
         |        |  |  +--rw desired-min-tx-interval     uint32
         |        |  |  +--rw required-min-rx-interval    uint32
         |        |  +--:(single-interval)
         |        |     +--rw min-interval                uint32
         |        +--rw demand-enabled?             boolean
         |        +--rw admin-down?                 boolean
         |        +--rw authentication-parms! {bfd-authentication}?
         |           +--rw key-chain?           kc:key-chain-ref
         |           +--rw replay-protection?   identityref
         +--ro oper
            +--ro micro-bfd-ipv4-session-statistics
            |  +--ro bfd-session-statistics
            |     +--ro session-count?              uint32
            |     +--ro session-up-count?           uint32
            |     +--ro session-down-count?         uint32
            |     +--ro session-admin-down-count?   uint32
            +--ro micro-bfd-ipv6-session-statistics
            |  +--ro bfd-session-statistics
            |     +--ro session-count?              uint32
            |     +--ro session-up-count?           uint32
            |     +--ro session-down-count?         uint32
            |     +--ro session-admin-down-count?   uint32
            +--ro session-lag* [lag-name]
               +--ro lag-name        if:interface-ref
               +--ro use-ipv4?       boolean
               +--ro use-ipv6?       boolean

Rahman, et al.         Expires September 11, 2017              [Page 13]
Internet-Draft                  BFD Yang                      March 2017

               +--ro member-links* [member-link]
                  +--ro member-link       if:interface-ref
                  +--ro micro-bfd-ipv4
                  |  +--ro path-type?              identityref
                  |  +--ro local-discriminator?    bfd-discriminator
                  |  +--ro remote-discriminator?   bfd-discriminator
                  |  +--ro remote-multiplier?      bfd-multiplier
                  |  +--ro out-interface?          if:interface-ref
                  |  +--ro demand-capability?      boolean
                  |  +--ro source-port?            inet:port-number
                  |  +--ro dest-port?              inet:port-number
                  |  +--ro session-running
                  |  |  +--ro session-index?             uint32
                  |  |  +--ro local-state?               bfd-state
                  |  |  +--ro remote-state?              bfd-state
                  |  |  +--ro local-diagnostic?          bfd-diagnostic
                  |  |  +--ro remote-diagnostic?         bfd-diagnostic
                  |  |  +--ro detection-mode?            enumeration
                  |  |  +--ro negotiated-tx-interval?    uint32
                  |  |  +--ro negotiated-rx-interval?    uint32
                  |  |  +--ro echo-tx-interval-in-use?   uint32
                  |  |  +--ro detection-time?            uint32
                  |  +--ro sesssion-statistics
                  |     +--ro create-time?            yang:date-and-time
                  |     +--ro last-down-time?         yang:date-and-time
                  |     +--ro last-up-time?           yang:date-and-time
                  |     +--ro down-count?             uint32
                  |     +--ro admin-down-count?       uint32
                  |     +--ro receive-packet-count?   uint64
                  |     +--ro send-packet-count?      uint64
                  |     +--ro receive-bad-packet?     uint64
                  |     +--ro send-failed-packet?     uint64
                  +--ro micro-bfd-ipv6
                     +--ro path-type?              identityref
                     +--ro local-discriminator?    bfd-discriminator
                     +--ro remote-discriminator?   bfd-discriminator
                     +--ro remote-multiplier?      bfd-multiplier
                     +--ro out-interface?          if:interface-ref
                     +--ro demand-capability?      boolean
                     +--ro source-port?            inet:port-number
                     +--ro dest-port?              inet:port-number
                     +--ro session-running
                     |  +--ro session-index?             uint32
                     |  +--ro local-state?               bfd-state
                     |  +--ro remote-state?              bfd-state
                     |  +--ro local-diagnostic?          bfd-diagnostic
                     |  +--ro remote-diagnostic?         bfd-diagnostic
                     |  +--ro detection-mode?            enumeration

Rahman, et al.         Expires September 11, 2017              [Page 14]
Internet-Draft                  BFD Yang                      March 2017

                     |  +--ro negotiated-tx-interval?    uint32
                     |  +--ro negotiated-rx-interval?    uint32
                     |  +--ro echo-tx-interval-in-use?   uint32
                     |  +--ro detection-time?            uint32
                     +--ro sesssion-statistics
                        +--ro create-time?            yang:date-and-time
                        +--ro last-down-time?         yang:date-and-time
                        +--ro last-up-time?           yang:date-and-time
                        +--ro down-count?             uint32
                        +--ro admin-down-count?       uint32
                        +--ro receive-packet-count?   uint64
                        +--ro send-packet-count?      uint64
                        +--ro receive-bad-packet?     uint64
                        +--ro send-failed-packet?     uint64
   notifications:
      +---n bfd-lag-notification
         +--ro local-discr?              bfd-discriminator
         +--ro remote-discr?             bfd-discriminator
         +--ro new-state?                bfd-state
         +--ro state-change-reason?      string
         +--ro time-in-previous-state?   string
         +--ro dest-addr?                inet:ip-address
         +--ro source-addr?              inet:ip-address
         +--ro session-index?            uint32
         +--ro path-type?                identityref
         +--ro lag-name?                 if:interface-ref
         +--ro member-link?              if:interface-ref

2.9.  BFD over MPLS LSPs hierarchy

   An "mpls" node is added under the "bfd" node in control-plane-
   protocol.  The configuration is per MPLS FEC under this "mpls" node.
   In the operational model we support multiple BFD sessions per MPLS
   FEC (ECMP), the local discriminator is used as key.  The "mpls" node
   can be mounted in a network device (top-level), in an LNE or in a
   network instance.

   module: ietf-bfd-mpls
   augment /rt:routing/rt:control-plane-protocols
           /rt:control-plane-protocol/bfd:bfd:
      +--rw mpls
         +--rw config
         |  +--rw egress
         |  |  +--rw local-multiplier?           bfd-multiplier
         |  |  +--rw (interval-config-type)?
         |  |  |  +--:(tx-rx-intervals)
         |  |  |  |  +--rw desired-min-tx-interval     uint32
         |  |  |  |  +--rw required-min-rx-interval    uint32

Rahman, et al.         Expires September 11, 2017              [Page 15]
Internet-Draft                  BFD Yang                      March 2017

         |  |  |  +--:(single-interval)
         |  |  |     +--rw min-interval                uint32
         |  |  +--rw authentication-parms! {bfd-authentication}?
         |  |     +--rw key-chain?           kc:key-chain-ref
         |  |     +--rw replay-protection?   identityref
         |  +--rw session-cfg
         |     +--rw sessions* [mpls-fec]
         |        +--rw mpls-fec                    inet:ip-address
         |        +--rw local-multiplier?           bfd-multiplier
         |        +--rw (interval-config-type)?
         |        |  +--:(tx-rx-intervals)
         |        |  |  +--rw desired-min-tx-interval     uint32
         |        |  |  +--rw required-min-rx-interval    uint32
         |        |  +--:(single-interval)
         |        |     +--rw min-interval                uint32
         |        +--rw demand-enabled?             boolean
         |        +--rw admin-down?                 boolean
         |        +--rw authentication-parms! {bfd-authentication}?
         |           +--rw key-chain?           kc:key-chain-ref
         |           +--rw replay-protection?   identityref
         +--ro oper
            +--ro bfd-session-statistics
            |  +--ro session-count?              uint32
            |  +--ro session-up-count?           uint32
            |  +--ro session-down-count?         uint32
            |  +--ro session-admin-down-count?   uint32
            +--ro session-group* [mpls-fec]
               +--ro mpls-fec    inet:ip-address
               +--ro sessions* [local-discriminator]
                  +--ro path-type?              identityref
                  +--ro local-discriminator     bfd-discriminator
                  +--ro remote-discriminator?   bfd-discriminator
                  +--ro remote-multiplier?      bfd-multiplier
                  +--ro out-interface?          if:interface-ref
                  +--ro demand-capability?      boolean
                  +--ro source-port?            inet:port-number
                  +--ro dest-port?              inet:port-number
                  +--ro session-running
                  |  +--ro session-index?             uint32
                  |  +--ro local-state?               bfd-state
                  |  +--ro remote-state?              bfd-state
                  |  +--ro local-diagnostic?          bfd-diagnostic
                  |  +--ro remote-diagnostic?         bfd-diagnostic
                  |  +--ro detection-mode?            enumeration
                  |  +--ro negotiated-tx-interval?    uint32
                  |  +--ro negotiated-rx-interval?    uint32
                  |  +--ro echo-tx-interval-in-use?   uint32
                  |  +--ro detection-time?            uint32

Rahman, et al.         Expires September 11, 2017              [Page 16]
Internet-Draft                  BFD Yang                      March 2017

                  +--ro sesssion-statistics
                  |  +--ro create-time?            yang:date-and-time
                  |  +--ro last-down-time?         yang:date-and-time
                  |  +--ro last-up-time?           yang:date-and-time
                  |  +--ro down-count?             uint32
                  |  +--ro admin-down-count?       uint32
                  |  +--ro receive-packet-count?   uint64
                  |  +--ro send-packet-count?      uint64
                  |  +--ro receive-bad-packet?     uint64
                  |  +--ro send-failed-packet?     uint64
                  +--ro mpls-dest-address?      inet:ip-address
   notifications:
      +---n bfd-mpls-notification
         +--ro local-discr?              bfd-discriminator
         +--ro remote-discr?             bfd-discriminator
         +--ro new-state?                bfd-state
         +--ro state-change-reason?      string
         +--ro time-in-previous-state?   string
         +--ro dest-addr?                inet:ip-address
         +--ro source-addr?              inet:ip-address
         +--ro session-index?            uint32
         +--ro path-type?                identityref
         +--ro mpls-dest-address?        inet:ip-address

2.10.  BFD over MPLS-TE hierarchy

   The MPLS-TE YANG model [I-D.ietf-teas-yang-te] is augmented.  BFD is
   configured per MPLS-TE tunnel, and BFD session operational data is
   provided per MPLS-TE LSP.

   module: ietf-bfd-mpls-te
   augment /rt:routing/rt:control-plane-protocols
           /rt:control-plane-protocol/bfd:bfd:
      +--rw mpls-te
         +--rw config
         |  +--rw egress
         |     +--rw local-multiplier?           bfd-multiplier
         |     +--rw (interval-config-type)?
         |     |  +--:(tx-rx-intervals)
         |     |  |  +--rw desired-min-tx-interval     uint32
         |     |  |  +--rw required-min-rx-interval    uint32
         |     |  +--:(single-interval)
         |     |     +--rw min-interval                uint32
         |     +--rw authentication-parms! {bfd-authentication}?
         |        +--rw key-chain?           kc:key-chain-ref
         |        +--rw replay-protection?   identityref
         +--ro oper
            +--ro bfd-session-statistics

Rahman, et al.         Expires September 11, 2017              [Page 17]
Internet-Draft                  BFD Yang                      March 2017

               +--ro session-count?              uint32
               +--ro session-up-count?           uint32
               +--ro session-down-count?         uint32
               +--ro session-admin-down-count?   uint32
   augment /te:te/te:tunnels/te:tunnel/te:config:
      +--rw local-multiplier?           bfd-multiplier
      +--rw (interval-config-type)?
      |  +--:(tx-rx-intervals)
      |  |  +--rw desired-min-tx-interval     uint32
      |  |  +--rw required-min-rx-interval    uint32
      |  +--:(single-interval)
      |     +--rw min-interval                uint32
      +--rw demand-enabled?             boolean
      +--rw admin-down?                 boolean
      +--rw authentication-parms! {bfd-authentication}?
      |  +--rw key-chain?           kc:key-chain-ref
      |  +--rw replay-protection?   identityref
      +--rw encap?                      identityref
   augment /te:te/te:lsps-state/te:lsp:
      +--ro path-type?              identityref
      +--ro local-discriminator?    bfd-discriminator
      +--ro remote-discriminator?   bfd-discriminator
      +--ro remote-multiplier?      bfd-multiplier
      +--ro out-interface?          if:interface-ref
      +--ro demand-capability?      boolean
      +--ro source-port?            inet:port-number
      +--ro dest-port?              inet:port-number
      +--ro session-running
      |  +--ro session-index?             uint32
      |  +--ro local-state?               bfd-state
      |  +--ro remote-state?              bfd-state
      |  +--ro local-diagnostic?          bfd-diagnostic
      |  +--ro remote-diagnostic?         bfd-diagnostic
      |  +--ro detection-mode?            enumeration
      |  +--ro negotiated-tx-interval?    uint32
      |  +--ro negotiated-rx-interval?    uint32
      |  +--ro echo-tx-interval-in-use?   uint32
      |  +--ro detection-time?            uint32
      +--ro sesssion-statistics
      |  +--ro create-time?            yang:date-and-time
      |  +--ro last-down-time?         yang:date-and-time
      |  +--ro last-up-time?           yang:date-and-time
      |  +--ro down-count?             uint32
      |  +--ro admin-down-count?       uint32
      |  +--ro receive-packet-count?   uint64
      |  +--ro send-packet-count?      uint64
      |  +--ro receive-bad-packet?     uint64
      |  +--ro send-failed-packet?     uint64

Rahman, et al.         Expires September 11, 2017              [Page 18]
Internet-Draft                  BFD Yang                      March 2017

      +--ro mpls-dest-address?      inet:ip-address
   notifications:
      +---n bfd-mpls-te-notification
         +--ro local-discr?              bfd-discriminator
         +--ro remote-discr?             bfd-discriminator
         +--ro new-state?                bfd-state
         +--ro state-change-reason?      string
         +--ro time-in-previous-state?   string
         +--ro dest-addr?                inet:ip-address
         +--ro source-addr?              inet:ip-address
         +--ro session-index?            uint32
         +--ro path-type?                identityref
         +--ro mpls-dest-address?        inet:ip-address
         +--ro tunnel-name?              string

2.11.  Examples

2.12.  Interaction with other YANG modules

   [I-D.ietf-lime-yang-connectionless-oam] describes how the LIME
   connectionless OAM model could be extended to support BFD.

   Also, the operation of the BFD data model depends on configuration
   parameters that are defined in other YANG modules.

2.12.1.  Module ietf-interfaces

   The following boolean configuration is defined in the "ietf-
   interfaces" YANG module [RFC7223]:

   /if:interfaces/if:interface/if:enabled
           If this configuration is set to "false", no BFD packets can
           be transmitted or received on that interface.

2.12.2.  Module ietf-ip

   The following boolean configuration is defined in the "ietf-ip" YANG
   module [RFC7277]:

   /if:interfaces/if:interface/ip:ipv4/ip:enabled
           If this configuration is set to "false", no BFD IPv4 packets
           can be transmitted or received on that interface.

   /if:interfaces/if:interface/ip:ipv4/ip:forwarding
           If this configuration is set to "false", no BFD IPv4 packets
           can be transmitted or received on that interface.

   /if:interfaces/if:interface/ip:ipv6/ip:enabled

Rahman, et al.         Expires September 11, 2017              [Page 19]
Internet-Draft                  BFD Yang                      March 2017

           If this configuration is set to "false", no BFD IPv6 packets
           can be transmitted or received on that interface.

   /if:interfaces/if:interface/ip:ipv6/ip:forwarding
           If this configuration is set to "false", no BFD IPv6 packets
           can be transmitted or received on that interface.

2.12.3.  Module ietf-mpls

   The following boolean configuration is defined in the "ietf-mpls"
   YANG module [I-D.ietf-mpls-base-yang]:

   /rt:routing/mpls:mpls/mpls:interface/mpls:config/mpls:enabled
           If this configuration is set to "false", no BFD MPLS packets
           can be transmitted or received on that interface.

2.12.4.  Module ietf-te

   The following configuration is defined in the "ietf-te" YANG module
   [I-D.ietf-teas-yang-te]:

   /ietf-te:te/ietf-te:tunnels/ietf-te:tunnel/ietf-te:config/ietf-
   te:admin-status
           If this configuration is not set to "state-up", no BFD MPLS
           packets can be transmitted or received on that tunnel.

2.13.  BFD top-level Yang Module

   <CODE BEGINS> file "ietf-bfd@2017-03-07.yang"
   module ietf-bfd {
     namespace "urn:ietf:params:xml:ns:yang:ietf-bfd";
     // replace with IANA namespace when assigned
     prefix "bfd";

     import ietf-interfaces {
       prefix "if";
     }

     import ietf-inet-types {
       prefix "inet";
     }

     import ietf-yang-types {
       prefix "yang";
     }

     import ietf-routing {
       prefix "rt";

Rahman, et al.         Expires September 11, 2017              [Page 20]
Internet-Draft                  BFD Yang                      March 2017

     }

     import ietf-key-chain {
       prefix "kc";
     }

     organization "IETF BFD Working Group";

     contact
       "WG Web:   <http://tools.ietf.org/wg/bfd>
        WG List:  <rtg-bfd@ietf.org>
        WG Chair: Jeff Haas
        WG Chair: Reshad Rahman
        Editor:   Lianshu Zheng and Reshad Rahman";

     description
       "This module contains the YANG definition for BFD parameters as
        per RFC5880.

        Copyright (c) 2017 IETF Trust and the persons
        identified as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject
        to the license terms contained in, the Simplified BSD License
        set forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC XXXX; see
        the RFC itself for full legal notices.";

     revision 2017-03-07 {
       description "Initial revision.";
       reference "RFC XXXX: A YANG data model for BFD";
     }

     // RFC Ed.: replace XXXX with actual RFC number and remove this
     // note

     identity bfdv1 {
       base "rt:control-plane-protocol";
       description "BFD protocol version 1 as per RFC5880.";
     }

     typedef bfd-discriminator {
       type uint32 {
         range 1..4294967295;

Rahman, et al.         Expires September 11, 2017              [Page 21]
Internet-Draft                  BFD Yang                      March 2017

       }
       description "BFD discriminator";
     }

     typedef bfd-diagnostic {
       type enumeration {
         enum none {
           value 0;
           description "None";
         }
         enum controlExpiry {
           value 1;
           description "Control timer expiry";
         }
         enum echoFailed {
           value 2;
           description "Echo failure";
         }
         enum nborDown {
           value 3;
           description "Neighbor down";
         }
         enum fwdingReset {
           value 4;
           description "Forwarding reset";
         }
         enum pathDown {
           value 5;
           description "Path down";
         }
         enum concPathDown {
           value 6;
           description "Concatenated path down";
         }
         enum adminDown {
           value 7;
           description "Admin down";
         }
         enum reverseConcPathDown {
           value 8;
           description "Reverse concatenated path down";
         }
       }
       description "BFD diagnostic";
     }

     typedef bfd-state {
       type enumeration {

Rahman, et al.         Expires September 11, 2017              [Page 22]
Internet-Draft                  BFD Yang                      March 2017

         enum adminDown {
           value 0;
           description "admindown";
         }
         enum down {
           value 1;
           description "down";
         }
         enum init {
           value 2;
           description "init";
         }
         enum up {
           value 3;
           description "up";
         }
       }
       description "BFD state";
     }

     typedef bfd-multiplier {
       type uint8 {
         range 1..255;
       }
       description "Multiplier";
     }

     typedef ttl {
       type uint8 {
         range 1..255;
       }
       description "Time To Live";
     }

     identity bfd-path-type {
       description
         "Base identity for BFD path type. The session type indicates
          the type of path on which BFD is running";
     }
     identity bfd-path-ip-sh {
       base bfd-path-type;
       description "BFD on IP single hop";
     }
     identity bfd-path-ip-mh {
       base bfd-path-type;
       description "BFD on IP multi hop";
     }
     identity bfd-path-mpls-te {

Rahman, et al.         Expires September 11, 2017              [Page 23]
Internet-Draft                  BFD Yang                      March 2017

       base bfd-path-type;
       description "BFD on MPLS Traffic Engineering";
     }
     identity bfd-path-mpls-lsp {
       base bfd-path-type;
       description "BFD on MPLS Label Switched Path";
     }
     identity bfd-path-lag {
       base bfd-path-type;
       description "Micro-BFD on LAG member links";
     }

     identity bfd-encap-type {
       description
         "Base identity for BFD encapsulation type.";
     }
     identity bfd-encap-ip {
       base bfd-encap-type;
       description "BFD with IP encapsulation.";
     }

     feature bfd-authentication {
       description "BFD authentication supported";
     }

     identity bfd-auth-replay-protection {
       description
         "Base identity for BFD authentication replay protection";
     }
     identity bfd-auth-replay-protection-non-meticulous {
       base bfd-auth-replay-protection;
       description "Non-meticulous (see RFC5880)";
     }
     identity bfd-auth-replay-protection-meticulous {
       base bfd-auth-replay-protection;
       description "Meticulous (see RFC5880)";
     }

     grouping bfd-auth-parms {
       description
         "Grouping for BFD authentication parameters
          (see section 6.7 of RFC5880).";
       container authentication-parms {
         if-feature bfd-authentication;
         presence
           "Enables BFD authentication (see section 6.7 of RFC5880).";
         description "Parameters for BFD authentication";

Rahman, et al.         Expires September 11, 2017              [Page 24]
Internet-Draft                  BFD Yang                      March 2017

         leaf key-chain {
           type kc:key-chain-ref;
           description "Name of key-chain";
         }

         leaf replay-protection {
           type identityref {
             base bfd-auth-replay-protection;
           }
           description
             "Protection against replays";
         }
       }
     }

     grouping bfd-grouping-base-cfg-parms {
       description "BFD grouping for base config parameters";
       leaf local-multiplier {
         type bfd-multiplier;
         default 3;
         description "Multiplier transmitted by local system";
       }

       choice interval-config-type {
         description
           "Two interval values or 1 value used for both tx and rx";
         case tx-rx-intervals {
           leaf desired-min-tx-interval {
             type uint32;
             units microseconds;
             mandatory true;
             description
               "Desired minimum transmit interval of control packets";
           }

           leaf required-min-rx-interval {
             type uint32;
             units microseconds;
             mandatory true;
             description
               "Required minimum receive interval of control packets";
           }
         }
         case single-interval {
           leaf min-interval {
             type uint32;
             units microseconds;
             mandatory true;

Rahman, et al.         Expires September 11, 2017              [Page 25]
Internet-Draft                  BFD Yang                      March 2017

             description
               "Desired minimum transmit interval and required " +
               "minimum receive interval of control packets";
           }
         }
       }
     }

     grouping bfd-grouping-common-cfg-parms {
       description "BFD grouping for common config parameters";

       uses bfd-grouping-base-cfg-parms;

       leaf demand-enabled {
         type boolean;
         default false;
         description "To enable demand mode";
       }

       leaf admin-down {
         type boolean;
         default false;
         description
           "Is the BFD session administratively down";
       }
       uses bfd-auth-parms;
     }

     grouping bfd-grouping-echo-cfg-parms {
       description "BFD grouping for echo config parameters";
       leaf desired-min-echo-tx-interval {
         type uint32;
         units microseconds;
         default 0;
         description "Desired minumum transmit interval for echo";
       }

       leaf required-min-echo-rx-interval {
         type uint32;
         units microseconds;
         default 0;
         description "Required minimum receive interval for echo";
       }
     }

     grouping bfd-client-base-cfg-parms {
       description
         "BFD grouping which could be used by a protocol which

Rahman, et al.         Expires September 11, 2017              [Page 26]
Internet-Draft                  BFD Yang                      March 2017

          is a client of BFD to enable its use of BFD";

       container bfd-cfg {
         description "BFD configuration";
         leaf enabled {
           type boolean;
           default false;
           description "True if BFD is enabled";
         }
       }
     }

     grouping bfd-all-session {
       description "BFD session operational information";
       leaf path-type {
         type identityref {
           base bfd-path-type;
         }
         description
           "BFD session type, this indicates the path type that BFD is
           running on";
       }
       leaf local-discriminator {
         type bfd-discriminator;
         description "Local discriminator";
       }
       leaf remote-discriminator {
         type bfd-discriminator;
         description "Remote discriminator";
       }
       leaf remote-multiplier {
         type bfd-multiplier;
         description "Remote multiplier";
       }
       leaf out-interface {
         type if:interface-ref;
         description "Outgoing physical interface name";
       }
       leaf demand-capability {
         type boolean;
         description "Local demand mode capability";
       }
       leaf source-port {
         type inet:port-number;
         description "Source UDP port";
       }
       leaf dest-port {
         type inet:port-number;

Rahman, et al.         Expires September 11, 2017              [Page 27]
Internet-Draft                  BFD Yang                      March 2017

         description "Destination UDP port";
       }

       container session-running {
         description "BFD session running information";
         leaf session-index {
           type uint32;
           description
             "An index used to uniquely identify BFD sessions";
         }
         leaf local-state {
           type bfd-state;
           description "Local state";
         }
         leaf remote-state {
           type bfd-state;
           description "Remote state";
         }
         leaf local-diagnostic {
           type bfd-diagnostic;
           description "Local diagnostic";
         }
         leaf remote-diagnostic {
           type bfd-diagnostic;
           description "Remote diagnostic";
         }
         leaf detection-mode {
           type enumeration {
             enum async-with-echo {
               value "1";
               description "Async with echo";
             }
             enum async-without-echo {
               value "2";
               description "Async without echo";
             }
             enum demand-with-echo {
               value "3";
               description "Demand with echo";
             }
             enum demand-without-echo {
               value "4";
               description "Demand without echo";
             }
           }
           description "Detection mode";
         }
         leaf negotiated-tx-interval {

Rahman, et al.         Expires September 11, 2017              [Page 28]
Internet-Draft                  BFD Yang                      March 2017

           type uint32;
           units microseconds;
           description "Negotiated transmit interval";
         }
         leaf negotiated-rx-interval {
           type uint32;
           units microseconds;
           description "Negotiated receive interval";
         }
         leaf echo-tx-interval-in-use {
           when "../../path-type = 'bfd-path-ip-sh'" {
             description
               "Echo is supported for IP single-hop only.";
           }
           type uint32;
           units microseconds;
           description "Echo transmit interval in use";
         }
         leaf detection-time {
           type uint32;
           units microseconds;
           description "Detection time";
         }
       }

       container sesssion-statistics {
         description "BFD per-session statistics";

         leaf create-time {
           type yang:date-and-time;
           description
             "Time and date when session was created";
         }
         leaf last-down-time {
           type yang:date-and-time;
           description
             "Time and date of last time the session went down";
         }
         leaf last-up-time {
           type yang:date-and-time;
           description
             "Time and date of last time the session went up";
         }
         leaf down-count {
           type uint32;
           description "Session Down Count";
         }
         leaf admin-down-count {

Rahman, et al.         Expires September 11, 2017              [Page 29]
Internet-Draft                  BFD Yang                      March 2017

           type uint32;
           description "Session Admin-Down Count";
         }
         leaf receive-packet-count {
           type uint64;
           description "Received Packet Count";
         }
         leaf send-packet-count {
           type uint64;
           description "Sent Packet Count";
         }
         leaf receive-bad-packet {
           type uint64;
           description "Received bad packet count";
         }
         leaf send-failed-packet {
           type uint64;
           description "Packet Failed to Send Count";
         }
       }
     }

     grouping bfd-session-statistics {
       description "Grouping for session counters";
       container bfd-session-statistics {
         description "BFD session counters";
         leaf session-count {
           type uint32;
           description "Number of sessions";
         }
         leaf session-up-count {
           type uint32;
           description "Count of sessions which are up";
         }
         leaf session-down-count {
           type uint32;
           description "Count of sessions which are down";
         }
         leaf session-admin-down-count {
           type uint32;
           description "Count of sessions which are admin-down";
         }
       }
     }

     grouping bfd-notification-parms {
       description
         "This group describes common parameters that will be sent " +

Rahman, et al.         Expires September 11, 2017              [Page 30]
Internet-Draft                  BFD Yang                      March 2017

         "as part of BFD notification";

       leaf local-discr {
         type bfd-discriminator;
         description "BFD local discriminator";
       }

       leaf remote-discr {
         type bfd-discriminator;
         description "BFD remote discriminator";
       }

       leaf new-state {
         type bfd-state;
         description "Current BFD state";
       }

       leaf state-change-reason {
         type string;
         description "BFD state change reason";
       }

       leaf time-in-previous-state {
         type string;
         description
           "How long the BFD session was in the previous state";
       }

       leaf dest-addr {
         type inet:ip-address;
         description "BFD peer address";
       }

       leaf source-addr {
         type inet:ip-address;
         description "BFD local address";
       }

       leaf session-index {
         type uint32;
         description "An index used to uniquely identify BFD sessions";
       }

       leaf path-type {
         type identityref {
           base bfd-path-type;
         }
         description "BFD path type";

Rahman, et al.         Expires September 11, 2017              [Page 31]
Internet-Draft                  BFD Yang                      March 2017

       }
     }

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol" {
        when "rt:type = 'bfd:bfdv1'" {
         description
           "This augmentation is only valid for a control-plane protocol
            instance of BFD (type 'bfdv1').";
       }
       description "BFD augmentation.";

       container bfd {
         description "BFD top level container";
         container config {
           description "BFD configuration container";
         }

         container oper {
           config "false";
           description "BFD operational container.";
           uses bfd-session-statistics;
         }
       }
     }
   }
   <CODE ENDS>

2.14.  BFD IP single-hop Yang Module

   <CODE BEGINS> file "ietf-bfd-ip-sh@2017-03-07.yang"
   module ietf-bfd-ip-sh {
     namespace "urn:ietf:params:xml:ns:yang:ietf-bfd-ip-sh";
     // replace with IANA namespace when assigned
     prefix "bfd-ip-sh";

     import ietf-bfd {
       prefix "bfd";
     }

     import ietf-interfaces {
       prefix "if";
     }

     import ietf-inet-types {
       prefix "inet";
     }

Rahman, et al.         Expires September 11, 2017              [Page 32]
Internet-Draft                  BFD Yang                      March 2017

     import ietf-routing {
       prefix "rt";
     }

     organization "IETF BFD Working Group";

     contact
       "WG Web:   <http://tools.ietf.org/wg/bfd>
        WG List:  <rtg-bfd@ietf.org>
        WG Chair: Jeff Haas
        WG Chair: Reshad Rahman
        Editor:   Lianshu Zheng and Reshad Rahman";

     description
       "This module contains the YANG definition for BFD IP single-hop
        as per RFC5881.

        Copyright (c) 2017 IETF Trust and the persons
        identified as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject
        to the license terms contained in, the Simplified BSD License
        set forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC XXXX; see
        the RFC itself for full legal notices.";

     revision 2017-03-07 {
       description "Initial revision.";
       reference "RFC XXXX: A YANG data model for BFD IP single-hop";
     }

     // RFC Ed.: replace XXXX with actual RFC number and remove this
     // note

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd" {
       description "BFD augmentation for IP single-hop";
       container ip-sh {
         description "BFD IP single-hop top level container";

         container config {
           description "BFD IP single-hop configuration container";
           container session-cfg {
             description "BFD IP single-hop session configuration";

Rahman, et al.         Expires September 11, 2017              [Page 33]
Internet-Draft                  BFD Yang                      March 2017

             list sessions {
               key "interface dest-addr";
               description "List of IP single-hop sessions";
               leaf interface {
                 type if:interface-ref;
                 description
                   "Interface on which the BFD session is running.";
               }
               leaf dest-addr {
                 type inet:ip-address;
                 description "IP address of the peer";
               }
               leaf source-addr {
                 type inet:ip-address;
                 description "Local address";
               }

               uses bfd:bfd-grouping-common-cfg-parms;

               uses bfd:bfd-grouping-echo-cfg-parms;
             }
           }
         }

         container oper {
           config "false";
           description "BFD IP single-hop operational container";

           uses bfd:bfd-session-statistics;

           list sessions {
             key "interface dest-addr";
             description "BFD IP single-hop sessions";
             leaf interface {
               type if:interface-ref;
               description
                 "Interface on which the BFD session is running.";
             }
             leaf dest-addr {
               type inet:ip-address;
               description "BFD peer address";
             }
             leaf source-addr {
               type inet:ip-address;
               description "BFD source address";
             }

             uses bfd:bfd-all-session;

Rahman, et al.         Expires September 11, 2017              [Page 34]
Internet-Draft                  BFD Yang                      March 2017

           }
         }
       }
     }

     notification bfd-singlehop-notification {
       description
         "Notification for BFD single-hop session state change. An " +
         "implementation may rate-limit notifications, e.g. when a" +
         "session is continuously changing state.";

       uses bfd:bfd-notification-parms;

       leaf interface {
         type if:interface-ref;
         description "Interface to which this BFD session belongs to";
       }

       leaf echo-enabled {
         type boolean;
         description "Was echo enabled for BFD";
       }
     }

   }
   <CODE ENDS>

2.15.  BFD IP multi-hop Yang Module

   <CODE BEGINS> file "ietf-bfd-ip-mh@2017-03-07.yang"
   module ietf-bfd-ip-mh {
     namespace "urn:ietf:params:xml:ns:yang:ietf-bfd-ip-mh";
     // replace with IANA namespace when assigned
     prefix "bfd-ip-mh";

     import ietf-bfd {
       prefix "bfd";
     }

     import ietf-inet-types {
       prefix "inet";
     }

     import ietf-routing {
       prefix "rt";
     }

     organization "IETF BFD Working Group";

Rahman, et al.         Expires September 11, 2017              [Page 35]
Internet-Draft                  BFD Yang                      March 2017

     contact
       "WG Web:   <http://tools.ietf.org/wg/bfd>
        WG List:  <rtg-bfd@ietf.org>
        WG Chair: Jeff Haas
        WG Chair: Reshad Rahman
        Editor:   Lianshu Zheng and Reshad Rahman";

     description
       "This module contains the YANG definition for BFD IP multi-hop
        as per RFC5883.

        Copyright (c) 2017 IETF Trust and the persons
        identified as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject
        to the license terms contained in, the Simplified BSD License
        set forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC XXXX; see
        the RFC itself for full legal notices.";

     revision 2017-03-07 {
       description "Initial revision.";
       reference "RFC XXXX: A YANG data model for BFD IP multi-hop";
     }

     // RFC Ed.: replace XXXX with actual RFC number and remove this
     // note

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd" {
       description "BFD augmentation for IP multi-hop";
       container ip-mh {
         description "BFD IP multi-hop top level container";

         container config {
           description "BFD IP multi-hop configuration container";
           container session-cfg {
             description "BFD IP multi-hop session configuration";

             list sessions {
               key "source-addr dest-addr";
               description "List of IP multi-hop sessions";

               leaf source-addr {

Rahman, et al.         Expires September 11, 2017              [Page 36]
Internet-Draft                  BFD Yang                      March 2017

                 type inet:ip-address;
                 description
                   "Local IP address";
               }
               leaf dest-addr {
                 type inet:ip-address;
                 description
                   "IP address of the peer";
               }
               uses bfd:bfd-grouping-common-cfg-parms;

               leaf tx-ttl {
                 type bfd:ttl;
                 default 255;
                 description "TTL of outgoing BFD control packets";
               }
               leaf rx-ttl {
                 type bfd:ttl;
                 mandatory true;
                 description
                   "Minimum allowed TTL value for incoming BFD control
                    packets";
               }
             }
           }
         }
         container oper {
           config "false";

           description "BFD IP multi-hop operational container";

           uses bfd:bfd-session-statistics;

           list session-group {
             key "source-addr dest-addr";
             description
               "BFD IP multi-hop group of sessions. A group of " +
               "sessions is between 1 source and 1 destination, " +
               "each session has a different field in UDP/IP hdr for " +
               "ECMP.";
             leaf source-addr {
               type inet:ip-address;
               description "BFD source address";
             }
             leaf dest-addr {
               type inet:ip-address;
               description "BFD peer address";
             }

Rahman, et al.         Expires September 11, 2017              [Page 37]
Internet-Draft                  BFD Yang                      March 2017

             list sessions {
               key "local-discriminator";
               description
                 "The BFD sessions between a source and a. " +
                 "destination. Local discriminator is unique for " +
                 "each session in the group.";
               leaf ttl {
                 type bfd:ttl;
                 description "TTL of outgoing packets";
               }
               uses bfd:bfd-all-session;
             }
           }
         }
       }
     }

     notification bfd-multihop-notification {
       description
         "Notification for BFD multi-hop session state change. An " +
         "implementation may rate-limit notifications, e.g. when a" +
         "session is continuously changing state.";

       uses bfd:bfd-notification-parms;
     }
   }
   <CODE ENDS>

2.16.  BFD over LAG Yang Module

   <CODE BEGINS> file "ietf-bfd-lag@2017-03-07.yang"
     namespace "urn:ietf:params:xml:ns:yang:ietf-bfd-lag";
     // replace with IANA namespace when assigned
     prefix "bfd-lag";

     import ietf-bfd {
       prefix "bfd";
     }

     import ietf-interfaces {
       prefix "if";
     }

     import ietf-inet-types {
       prefix "inet";
     }

     import ietf-routing {

Rahman, et al.         Expires September 11, 2017              [Page 38]
Internet-Draft                  BFD Yang                      March 2017

       prefix "rt";
     }

     organization "IETF BFD Working Group";

     contact
       "WG Web:   <http://tools.ietf.org/wg/bfd>
        WG List:  <rtg-bfd@ietf.org>
        WG Chair: Jeff Haas
        WG Chair: Reshad Rahman
        Editor:   Lianshu Zheng and Reshad Rahman";

     description
       "This module contains the YANG definition for BFD over LAG
        interfaces as per RFC7130.

        Copyright (c) 2017 IETF Trust and the persons
        identified as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject
        to the license terms contained in, the Simplified BSD License
        set forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC XXXX; see
        the RFC itself for full legal notices.";

     revision 2017-03-07 {
       description "Initial revision.";
       reference "RFC XXXX: A YANG data model for BFD over LAG";
     }

     // RFC Ed.: replace XXXX with actual RFC number and remove this
     // note

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd" {
       description "BFD augmentation for LAG";
       container lag {
         description "BFD over LAG top level container";

         container config {
           description "BFD over LAG configuration container";
           container session-cfg {
             description "BFD over LAG session configuration";
             list sessions {

Rahman, et al.         Expires September 11, 2017              [Page 39]
Internet-Draft                  BFD Yang                      March 2017

               key "lag-name";
               description "A LAG interface on which BFD is running";
               leaf lag-name {
                 type if:interface-ref ;
                 description "Name of the LAG";
               }
               leaf ipv4-dest-addr {
                 type inet:ipv4-address;
                 description
                   "IPv4 address of the peer, for IPv4 micro-BFD.";
               }
               leaf ipv6-dest-addr {
                 type inet:ipv6-address;
                 description
                   "IPv6 address of the peer, for IPv6 micro-BFD.";
               }
               uses bfd:bfd-grouping-common-cfg-parms;
             }
           }
         }

         container oper {
           config "false";
           description "BFD over LAG operational container.";

           container micro-bfd-ipv4-session-statistics {
             description "Micro-BFD IPv4 session counters";
             uses bfd:bfd-session-statistics;
           }
           container micro-bfd-ipv6-session-statistics {
             description "Micro-BFD IPv6 session counters";
             uses bfd:bfd-session-statistics;
           }

           list session-lag {
             key "lag-name";
             description "A LAG interface on which BFD is running";
             leaf lag-name {
               type if:interface-ref ;
               description "Name of the LAG";
             }

             leaf use-ipv4 {
               type boolean;
               description "Using IPv4 micro-BFD.";
             }
             leaf use-ipv6 {
               type boolean;

Rahman, et al.         Expires September 11, 2017              [Page 40]
Internet-Draft                  BFD Yang                      March 2017

               description "Using IPv6 micro-BFD.";
             }

             list member-links {
               key "member-link";
               description
                 "Micro-BFD over LAG. This represents one member link";

               leaf member-link {
                 type if:interface-ref;
                 description
                   "Member link on which micro-BFD is running";
               }
               container micro-bfd-ipv4 {
                 when "../../use-ipv4 = 'true'" {
                   description "Needed only if IPv4 is used.";
                 }
                 description
                   "Micro-BFD IPv4 session state on member link";
                 uses bfd:bfd-all-session;
               }
               container micro-bfd-ipv6 {
                 when "../../use-ipv6 = 'true'" {
                   description "Needed only if IPv6 is used.";
                 }
                 description
                   "Micro-BFD IPv6 session state on member link";
                 uses bfd:bfd-all-session;
               }
             }
           }
         }
       }
     }

     notification bfd-lag-notification {
       description
         "Notification for BFD over LAG session state change. " +
         "An implementation may rate-limit notifications, e.g. when a" +
         "session is continuously changing state.";

       uses bfd:bfd-notification-parms;

       leaf lag-name {
         type if:interface-ref;
         description "LAG interface name";
       }

Rahman, et al.         Expires September 11, 2017              [Page 41]
Internet-Draft                  BFD Yang                      March 2017

       leaf member-link {
         type if:interface-ref;
         description "Member link on which BFD is running";
       }
     }
   }
   <CODE ENDS>

2.17.  BFD over MPLS Yang Module

   <CODE BEGINS> file "ietf-bfd-mpls@2017-03-07.yang"
   module ietf-bfd-mpls {
     namespace "urn:ietf:params:xml:ns:yang:ietf-bfd-mpls";
     // replace with IANA namespace when assigned
     prefix "bfd-mpls";

     import ietf-bfd {
       prefix "bfd";
     }

     import ietf-inet-types {
       prefix "inet";
     }

     import ietf-routing {
       prefix "rt";
     }

     organization "IETF BFD Working Group";

     contact
       "WG Web:   <http://tools.ietf.org/wg/bfd>
        WG List:  <rtg-bfd@ietf.org>
        WG Chair: Jeff Haas
        WG Chair: Reshad Rahman
        Editor:   Lianshu Zheng and Reshad Rahman";

     description
       "This module contains the YANG definition for BFD parameters for
        MPLS LSPs as per RFC5884.

        Copyright (c) 2017 IETF Trust and the persons
        identified as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject
        to the license terms contained in, the Simplified BSD License
        set forth in Section 4.c of the IETF Trust's Legal Provisions

Rahman, et al.         Expires September 11, 2017              [Page 42]
Internet-Draft                  BFD Yang                      March 2017

        Relating to IETF Documents
        (http://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC XXXX; see
        the RFC itself for full legal notices.";

     revision 2017-03-07 {
       description "Initial revision.";
       reference "RFC XXXX: A YANG data model for BFD over MPLS LSPs";
     }

     // RFC Ed.: replace XXXX with actual RFC number and remove this
     // note

     identity bfd-encap-gach {
       base bfd:bfd-encap-type;
       description
         "BFD with G-ACh encapsulation as per RFC5586.";
     }

     identity bfd-encap-ip-gach {
       base bfd:bfd-encap-type;
       description
         "BFD with IP and G-ACh encapsulation as per RFC5586.";
     }

     grouping bfd-encap-cfg {
       description "Configuration for BFD encapsulation";

       leaf encap {
         type identityref {
           base bfd:bfd-encap-type;
         }
         default bfd:bfd-encap-ip;
         description "BFD encapsulation";
       }
     }

     grouping bfd-mpls-dest-address {
       description "Destination address as per RFC5884";

       leaf mpls-dest-address {
         type inet:ip-address;
         config "false";
         description
           "Destination address as per RFC5884.
            Needed if IP encapsulation is used";
       }

Rahman, et al.         Expires September 11, 2017              [Page 43]
Internet-Draft                  BFD Yang                      March 2017

     }

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd" {
       description "BFD augmentation for MPLS";
       container mpls {
         description "BFD MPLS top level container";

         container config {
           description "BFD MPLS configuration container";

           container egress {
             description "Egress configuration";

             uses bfd:bfd-grouping-base-cfg-parms;

             uses bfd:bfd-auth-parms;
           }

           container session-cfg {
             description "BFD MPLS session configuration";
             list sessions {
               key "mpls-fec";
               description "List of BFD MPLS sessions";
               leaf mpls-fec {
                 type inet:ip-address;
                 description "MPLS FEC";
               }

               uses bfd:bfd-grouping-common-cfg-parms;
             }
           }
         }

         container oper {
           config "false";

           description "BFD MPLS operational container";

           uses bfd:bfd-session-statistics;

           list session-group {
             key "mpls-fec";
             description
               "BFD MPLS group of sessions. A group of sessions is" +
               "for 1 FEC, each session has a different field in " +
               "UDP/IP hdr for ECMP.";

Rahman, et al.         Expires September 11, 2017              [Page 44]
Internet-Draft                  BFD Yang                      March 2017

             leaf mpls-fec {
               type inet:ip-address;
               description "MPLS-FEC";
             }
             list sessions {
               key "local-discriminator";
               description
                 "The BFD sessions for an MPLS FEC. Local " +
                 "discriminator is unique for each session in the " +
                 "group.";
               uses bfd:bfd-all-session;

               uses bfd-mpls:bfd-mpls-dest-address;
             }
           }

         }
       }
     }

     notification bfd-mpls-notification {
       description
         "Notification for BFD over MPLS FEC session state change. " +
         "An implementation may rate-limit notifications, e.g. when a" +
         "session is continuously changing state.";

       uses bfd:bfd-notification-parms;

       leaf mpls-dest-address {
         type inet:ip-address;
         description
           "Destination address as per RFC5884.
            Needed if IP encapsulation is used";
       }
     }
   }
   <CODE ENDS>

2.18.  BFD over MPLS-TE Yang Module

   <CODE BEGINS> file "ietf-bfd-mpls-te@2017-03-07.yang"
   module ietf-bfd-mpls-te {
     namespace "urn:ietf:params:xml:ns:yang:ietf-bfd-mpls-te";
     // replace with IANA namespace when assigned
     prefix "bfd-mpls-te";

     import ietf-bfd {
       prefix "bfd";

Rahman, et al.         Expires September 11, 2017              [Page 45]
Internet-Draft                  BFD Yang                      March 2017

     }

     import ietf-bfd-mpls {
       prefix "bfd-mpls";
     }

     import ietf-te {
       prefix "te";
     }

     import ietf-routing {
       prefix "rt";
     }

     organization "IETF BFD Working Group";

     contact
       "WG Web:   <http://tools.ietf.org/wg/bfd>
        WG List:  <rtg-bfd@ietf.org>
        WG Chair: Jeff Haas
        WG Chair: Reshad Rahman
        Editor:   Lianshu Zheng and Reshad Rahman";

     description
       "This module contains the YANG definition for BFD parameters for
        MPLS Traffic Engineering as per RFC5884.

        Copyright (c) 2017 IETF Trust and the persons
        identified as authors of the code.  All rights reserved.

        Redistribution and use in source and binary forms, with or
        without modification, is permitted pursuant to, and subject
        to the license terms contained in, the Simplified BSD License
        set forth in Section 4.c of the IETF Trust's Legal Provisions
        Relating to IETF Documents
        (http://trustee.ietf.org/license-info).

        This version of this YANG module is part of RFC XXXX; see
        the RFC itself for full legal notices.";

     revision 2017-03-07 {
       description "Initial revision.";
       reference "RFC XXXX: A YANG data model for BFD over MPLS-TE";
     }

     // RFC Ed.: replace XXXX with actual RFC number and remove this
     // note

Rahman, et al.         Expires September 11, 2017              [Page 46]
Internet-Draft                  BFD Yang                      March 2017

     augment "/rt:routing/rt:control-plane-protocols/"
           + "rt:control-plane-protocol/bfd:bfd" {
       description "BFD augmentation for MPLS-TE";
       container mpls-te {
         description "BFD MPLS-TE top level container";

         container config {
           description "BFD MPLS-TE configuration container";

           container egress {
             description "Egress configuration";

             uses bfd:bfd-grouping-base-cfg-parms;

             uses bfd:bfd-auth-parms;
           }
         }

         container oper {
           config "false";
           description "BFD operational container";
           uses bfd:bfd-session-statistics;
         }
       }
     }

     augment "/te:te/te:tunnels/te:tunnel/te:config" {
       description "BFD configuration on MPLS-TE tunnel.";

       uses bfd:bfd-grouping-common-cfg-parms;

       uses bfd-mpls:bfd-encap-cfg;
     }

     augment "/te:te/te:lsps-state/te:lsp" {
       when "/te:te/te:lsps-state/te:lsp/te:origin-type != 'transit'" {
         description "BFD information not needed at transit points";
       }
       description "BFD state information on MPLS-TE LSP.";

       uses bfd:bfd-all-session;

       uses bfd-mpls:bfd-mpls-dest-address;
     }

     notification bfd-mpls-te-notification {
       description

Rahman, et al.         Expires September 11, 2017              [Page 47]
Internet-Draft                  BFD Yang                      March 2017

         "Notification for BFD over MPLS-TE session state change. " +
         "An implementation may rate-limit notifications, e.g. when a" +
         "session is continuously changing state.";

       uses bfd:bfd-notification-parms;

       uses bfd-mpls:bfd-mpls-dest-address;

       leaf tunnel-name {
         type string;
         description "MPLS-TE tunnel on which BFD was running.";
       }
     }
   }
   <CODE ENDS>

2.19.  Security Considerations

   The YANG module defined in this memo is designed to be accessed via
   the NETCONF protocol [RFC6241].  The lowest NETCONF layer is the
   secure transport layer and the mandatory to implement secure
   transport is SSH [RFC6242].  The NETCONF access control model
   [RFC6536] provides the means to restrict access for particular
   NETCONF users to a pre-configured subset of all available NETCONF
   protocol operations and content.

   The YANG module has writeable data nodes which can be used for
   creation of BFD sessions and modification of BFD session parameters.
   The system should "police" creation of BFD sessions to prevent new
   sessions from causing existing BFD sessions to fail.  For BFD session
   modification, the BFD protocol has mechanisms in place which allow
   for in service modification.

2.20.  IANA Considerations

   The IANA is requested to as assign a new new namespace URI from the
   IETF XML registry.

   URI:TBD

2.21.  Acknowledgements

   We would also like to thank Nobo Akiya and Jeff Haas for their
   encouragement on this work.  We would also like to thank Rakesh
   Gandhi and Tarek Saad for their help on the MPLS-TE model.  We would
   also like to thank Acee Lindem for his guidance.

Rahman, et al.         Expires September 11, 2017              [Page 48]
Internet-Draft                  BFD Yang                      March 2017

3.  References

3.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <http://www.rfc-editor.org/info/rfc2119>.

   [RFC5586]  Bocci, M., Ed., Vigoureux, M., Ed., and S. Bryant, Ed.,
              "MPLS Generic Associated Channel", RFC 5586,
              DOI 10.17487/RFC5586, June 2009,
              <http://www.rfc-editor.org/info/rfc5586>.

   [RFC5880]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
              (BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010,
              <http://www.rfc-editor.org/info/rfc5880>.

   [RFC5881]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
              (BFD) for IPv4 and IPv6 (Single Hop)", RFC 5881,
              DOI 10.17487/RFC5881, June 2010,
              <http://www.rfc-editor.org/info/rfc5881>.

   [RFC5882]  Katz, D. and D. Ward, "Generic Application of
              Bidirectional Forwarding Detection (BFD)", RFC 5882,
              DOI 10.17487/RFC5882, June 2010,
              <http://www.rfc-editor.org/info/rfc5882>.

   [RFC5883]  Katz, D. and D. Ward, "Bidirectional Forwarding Detection
              (BFD) for Multihop Paths", RFC 5883, DOI 10.17487/RFC5883,
              June 2010, <http://www.rfc-editor.org/info/rfc5883>.

   [RFC5884]  Aggarwal, R., Kompella, K., Nadeau, T., and G. Swallow,
              "Bidirectional Forwarding Detection (BFD) for MPLS Label
              Switched Paths (LSPs)", RFC 5884, DOI 10.17487/RFC5884,
              June 2010, <http://www.rfc-editor.org/info/rfc5884>.

   [RFC5885]  Nadeau, T., Ed. and C. Pignataro, Ed., "Bidirectional
              Forwarding Detection (BFD) for the Pseudowire Virtual
              Circuit Connectivity Verification (VCCV)", RFC 5885,
              DOI 10.17487/RFC5885, June 2010,
              <http://www.rfc-editor.org/info/rfc5885>.

   [RFC6020]  Bjorklund, M., Ed., "YANG - A Data Modeling Language for
              the Network Configuration Protocol (NETCONF)", RFC 6020,
              DOI 10.17487/RFC6020, October 2010,
              <http://www.rfc-editor.org/info/rfc6020>.

Rahman, et al.         Expires September 11, 2017              [Page 49]
Internet-Draft                  BFD Yang                      March 2017

   [RFC6241]  Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed.,
              and A. Bierman, Ed., "Network Configuration Protocol
              (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, June 2011,
              <http://www.rfc-editor.org/info/rfc6241>.

   [RFC7130]  Bhatia, M., Ed., Chen, M., Ed., Boutros, S., Ed.,
              Binderberger, M., Ed., and J. Haas, Ed., "Bidirectional
              Forwarding Detection (BFD) on Link Aggregation Group (LAG)
              Interfaces", RFC 7130, DOI 10.17487/RFC7130, February
              2014, <http://www.rfc-editor.org/info/rfc7130>.

   [RFC7223]  Bjorklund, M., "A YANG Data Model for Interface
              Management", RFC 7223, DOI 10.17487/RFC7223, May 2014,
              <http://www.rfc-editor.org/info/rfc7223>.

   [RFC7277]  Bjorklund, M., "A YANG Data Model for IP Management",
              RFC 7277, DOI 10.17487/RFC7277, June 2014,
              <http://www.rfc-editor.org/info/rfc7277>.

   [RFC8022]  Lhotka, L. and A. Lindem, "A YANG Data Model for Routing
              Management", RFC 8022, DOI 10.17487/RFC8022, November
              2016, <http://www.rfc-editor.org/info/rfc8022>.

3.2.  Informative References

   [I-D.ietf-lime-yang-connectionless-oam]
              Kumar, D., Wang, Z., Wu, Q., Rahman, R., and S. Raghavan,
              "Generic YANG Data Model for Connectionless Operations,
              Administration, and Maintenance(OAM) protocols", draft-
              ietf-lime-yang-connectionless-oam-04 (work in progress),
              February 2017.

   [I-D.ietf-mpls-base-yang]
              Raza, K., Gandhi, R., Liu, X., Beeram, V., Saad, T.,
              Bryskin, I., Chen, X., Jones, R., and B. Wen, "A YANG Data
              Model for MPLS Base", draft-ietf-mpls-base-yang-02 (work
              in progress), March 2017.

   [I-D.ietf-netconf-restconf]
              Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF
              Protocol", draft-ietf-netconf-restconf-18 (work in
              progress), October 2016.

   [I-D.ietf-netmod-routing-cfg]
              Lhotka, L. and A. Lindem, "A YANG Data Model for Routing
              Management", draft-ietf-netmod-routing-cfg-25 (work in
              progress), November 2016.

Rahman, et al.         Expires September 11, 2017              [Page 50]
Internet-Draft                  BFD Yang                      March 2017

   [I-D.ietf-netmod-schema-mount]
              Bjorklund, M. and L. Lhotka, "YANG Schema Mount", draft-
              ietf-netmod-schema-mount-04 (work in progress), March
              2017.

   [I-D.ietf-rtgwg-device-model]
              Lindem, A., Berger, L., Bogdanovic, D., and C. Hopps,
              "Network Device YANG Organizational Models", draft-ietf-
              rtgwg-device-model-01 (work in progress), October 2016.

   [I-D.ietf-rtgwg-lne-model]
              Berger, L., Hopps, C., Lindem, A., and D. Bogdanovic,
              "YANG Logical Network Elements", draft-ietf-rtgwg-lne-
              model-01 (work in progress), October 2016.

   [I-D.ietf-rtgwg-ni-model]
              Berger, L., Hopps, C., Lindem, A., and D. Bogdanovic,
              "YANG Network Instances", draft-ietf-rtgwg-ni-model-01
              (work in progress), October 2016.

   [I-D.ietf-rtgwg-yang-key-chain]
              Lindem, A., Qu, Y., Yeung, D., Chen, I., Zhang, Z., and Y.
              Yang, "Routing Key Chain YANG Data Model", draft-ietf-
              rtgwg-yang-key-chain-15 (work in progress), February 2017.

   [I-D.ietf-teas-yang-te]
              Saad, T., Gandhi, R., Liu, X., Beeram, V., Shah, H.,
              Bryskin, I., Chen, X., Jones, R., and B. Wen, "A YANG Data
              Model for Traffic Engineering Tunnels and Interfaces",
              draft-ietf-teas-yang-te-05 (work in progress), October
              2016.

Appendix A.  Change log

   RFC Editor: Remove this section upon publication as an RFC.

A.1.  Changes between versions -04 and -05

   o  "bfd" node in augment of control-plane-protocol as per [RFC8022].

   o  Removed augment of network-instance.  Replaced by schema-mount.

   o  Added information on interaction with other YANG modules.

Rahman, et al.         Expires September 11, 2017              [Page 51]
Internet-Draft                  BFD Yang                      March 2017

A.2.  Changes between versions -03 and -04

   o  Updated author information.

   o  Fixed YANG compile error in ietf-bfd-lag.yang which was due to
      incorrect when statement.

A.3.  Changes between versions -02 and -03

   o  Fixed YANG compilation warning due to incorrect revision date in
      ietf-bfd-ip-sh module.

A.4.  Changes between versions -01 and -02

   o  Replace routing-instance, which has been removed from
      [I-D.ietf-netmod-routing-cfg], with network-instance from
      [I-D.ietf-rtgwg-ni-model]

A.5.  Changes between versions -00 and -01

   o  Remove BFD configuration parameters from BFD clients, all BFD
      configuration parameters in BFD

   o  YANG module split in multiple YANG modules (one per type of
      forwarding path)

   o  For BFD over MPLS-TE we augment MPLS-TE model

   o  For BFD authentication we now use key-chain in
      [I-D.ietf-rtgwg-yang-key-chain]

Authors' Addresses

   Reshad Rahman (editor)
   Cisco Systems
   Canada

   Email: rrahman@cisco.com

   Lianshu Zheng (editor)
   Huawei Technologies
   China

   Email: vero.zheng@huawei.com

Rahman, et al.         Expires September 11, 2017              [Page 52]
Internet-Draft                  BFD Yang                      March 2017

   Santosh Pallagatti
   India

   Email: santosh.pallagatti@gmail.com

   Mahesh Jethanandani
   Cisco Systems

   Email: mjethanandani@gmail.com

   Greg Mirsky
   ZTE Corporation

   Email: gregimirsky@gmail.com

Rahman, et al.         Expires September 11, 2017              [Page 53]