Skip to main content

IPv6 Segment Routing Header (SRH)
draft-ietf-6man-segment-routing-header-19

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8754.
Authors Clarence Filsfils , Darren Dukes , Stefano Previdi , John Leddy , Satoru Matsushima , Daniel Voyer
Last updated 2019-05-22
Replaces draft-previdi-6man-segment-routing-header
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state In WG Last Call
Document shepherd Bob Hinden
IESG IESG state Became RFC 8754 (Proposed Standard)
Consensus boilerplate Yes
Telechat date (None)
Responsible AD (None)
Send notices to Robert Hinden <bob.hinden@gmail.com>
draft-ietf-6man-segment-routing-header-19
Network Working Group                                   C. Filsfils, Ed.
Internet-Draft                                             D. Dukes, Ed.
Intended status: Standards Track                     Cisco Systems, Inc.
Expires: November 22, 2019                                    S. Previdi
                                                                  Huawei
                                                                J. Leddy
                                                              Individual
                                                           S. Matsushima
                                                                Softbank
                                                           D. Voyer, Ed.
                                                             Bell Canada
                                                            May 21, 2019

                   IPv6 Segment Routing Header (SRH)
               draft-ietf-6man-segment-routing-header-19

Abstract

   Segment Routing can be applied to the IPv6 data plane using a new
   type of Routing Extension Header.  This document describes the
   Segment Routing Extension Header and how it is used by Segment
   Routing capable nodes.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on November 22, 2019.

Copyright Notice

   Copyright (c) 2019 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents

Filsfils, et al.        Expires November 22, 2019               [Page 1]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Requirements Language . . . . . . . . . . . . . . . . . .   3
   2.  Segment Routing Extension Header  . . . . . . . . . . . . . .   4
     2.1.  SRH TLVs  . . . . . . . . . . . . . . . . . . . . . . . .   5
       2.1.1.  Padding TLVs  . . . . . . . . . . . . . . . . . . . .   7
       2.1.2.  HMAC TLV  . . . . . . . . . . . . . . . . . . . . . .   8
   3.  SR Nodes  . . . . . . . . . . . . . . . . . . . . . . . . . .  11
     3.1.  Source SR Node  . . . . . . . . . . . . . . . . . . . . .  11
     3.2.  Transit Node  . . . . . . . . . . . . . . . . . . . . . .  12
     3.3.  SR Segment Endpoint Node  . . . . . . . . . . . . . . . .  12
   4.  Packet Processing . . . . . . . . . . . . . . . . . . . . . .  12
     4.1.  Source SR Node  . . . . . . . . . . . . . . . . . . . . .  12
       4.1.1.  Reduced SRH . . . . . . . . . . . . . . . . . . . . .  13
     4.2.  Transit Node  . . . . . . . . . . . . . . . . . . . . . .  13
     4.3.  SR Segment Endpoint Node  . . . . . . . . . . . . . . . .  13
       4.3.1.  FIB Entry Is Locally Instantiated SRv6 SID  . . . . .  14
       4.3.2.  FIB Entry is a Local Interface  . . . . . . . . . . .  16
       4.3.3.  FIB Entry Is A Non-Local Route  . . . . . . . . . . .  17
       4.3.4.  FIB Entry Is A No Match . . . . . . . . . . . . . . .  17
   5.  Intra SR Domain Deployment Model  . . . . . . . . . . . . . .  17
     5.1.  Securing the SR Domain  . . . . . . . . . . . . . . . . .  17
     5.2.  SR Domain as a single system with delegation among
           components  . . . . . . . . . . . . . . . . . . . . . . .  18
     5.3.  MTU Considerations  . . . . . . . . . . . . . . . . . . .  19
     5.4.  ICMP Error Processing . . . . . . . . . . . . . . . . . .  19
     5.5.  Load Balancing and ECMP . . . . . . . . . . . . . . . . .  19
     5.6.  Other Deployments . . . . . . . . . . . . . . . . . . . .  20
   6.  Illustrations . . . . . . . . . . . . . . . . . . . . . . . .  20
     6.1.  Abstract Representation of an SRH . . . . . . . . . . . .  20
     6.2.  Example Topology  . . . . . . . . . . . . . . . . . . . .  21
     6.3.  Source SR Node  . . . . . . . . . . . . . . . . . . . . .  21
       6.3.1.  Intra SR Domain Packet  . . . . . . . . . . . . . . .  22
       6.3.2.  Inter SR Domain Packet - Transit  . . . . . . . . . .  22
       6.3.3.  Inter SR Domain Packet - Internal to External . . . .  22
     6.4.  Transit Node  . . . . . . . . . . . . . . . . . . . . . .  23
     6.5.  SR Segment Endpoint Node  . . . . . . . . . . . . . . . .  23
     6.6.  Delegation of Function with HMAC Verification . . . . . .  23
       6.6.1.  SID List Verification . . . . . . . . . . . . . . . .  23

Filsfils, et al.        Expires November 22, 2019               [Page 2]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   7.  Security Considerations . . . . . . . . . . . . . . . . . . .  24
     7.1.  Source Routing Attacks  . . . . . . . . . . . . . . . . .  24
     7.2.  Service Theft . . . . . . . . . . . . . . . . . . . . . .  25
     7.3.  Topology Disclosure . . . . . . . . . . . . . . . . . . .  25
     7.4.  ICMP Generation . . . . . . . . . . . . . . . . . . . . .  25
     7.5.  Applicability of AH . . . . . . . . . . . . . . . . . . .  26
   8.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  26
     8.1.  Segment Routing Header Flags Register . . . . . . . . . .  27
     8.2.  Segment Routing Header TLVs Register  . . . . . . . . . .  27
   9.  Implementation Status . . . . . . . . . . . . . . . . . . . .  27
     9.1.  Linux . . . . . . . . . . . . . . . . . . . . . . . . . .  27
     9.2.  Cisco Systems . . . . . . . . . . . . . . . . . . . . . .  28
     9.3.  FD.io . . . . . . . . . . . . . . . . . . . . . . . . . .  28
     9.4.  Barefoot  . . . . . . . . . . . . . . . . . . . . . . . .  28
     9.5.  Juniper . . . . . . . . . . . . . . . . . . . . . . . . .  28
     9.6.  Huawei  . . . . . . . . . . . . . . . . . . . . . . . . .  28
   10. Contributors  . . . . . . . . . . . . . . . . . . . . . . . .  29
   11. Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  29
   12. References  . . . . . . . . . . . . . . . . . . . . . . . . .  29
     12.1.  Normative References . . . . . . . . . . . . . . . . . .  29
     12.2.  Informative References . . . . . . . . . . . . . . . . .  30
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  31

1.  Introduction

   Segment Routing can be applied to the IPv6 data plane using a new
   type of Routing Extension Header (SRH).  This document describes the
   Segment Routing Extension Header and how it is used by Segment
   Routing capable nodes.

   The Segment Routing Architecture [RFC8402] describes Segment Routing
   and its instantiation in two data planes MPLS and IPv6.

   The encoding of IPv6 segments in the Segment Routing Extension Header
   is defined in this document.

   Terminology used within this document is defined in detail in
   [RFC8402].  Specifically, these terms: Segment Routing, SR Domain,
   SRv6, Segment ID (SID), SRv6 SID, Active Segment, and SR Policy.

1.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and
   "OPTIONAL" in this document are to be interpreted as described in BCP
   14 [RFC2119] [RFC8174] when, and only when, they appear in all
   capitals, as shown here.

Filsfils, et al.        Expires November 22, 2019               [Page 3]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

2.  Segment Routing Extension Header

   Routing Headers are defined in [RFC8200].  The Segment Routing Header
   has a new Routing Type (suggested value 4) to be assigned by IANA.

   The Segment Routing Header (SRH) is defined as follows:

     0                   1                   2                   3
     0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    | Next Header   |  Hdr Ext Len  | Routing Type  | Segments Left |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |  Last Entry   |     Flags     |              Tag              |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    |            Segment List[0] (128 bits IPv6 address)            |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    |                                                               |
                                  ...
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    |                                                               |
    |            Segment List[n] (128 bits IPv6 address)            |
    |                                                               |
    |                                                               |
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
    //                                                             //
    //         Optional Type Length Value objects (variable)       //
    //                                                             //
    +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   where:

   o  Next Header: Defined in [RFC8200] Section 4.4

   o  Hdr Ext Len: Defined in [RFC8200] Section 4.4

   o  Routing Type: TBD, to be assigned by IANA (suggested value: 4).

   o  Segments Left: Defined in [RFC8200] Section 4.4

   o  Last Entry: contains the index (zero based), in the Segment List,
      of the last element of the Segment List.

Filsfils, et al.        Expires November 22, 2019               [Page 4]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   o  Flags: 8 bits of flags.  Section 8.1 creates an IANA registry for
      new flags to be defined.  The following flags are defined:

          0 1 2 3 4 5 6 7
         +-+-+-+-+-+-+-+-+
         |U U U U U U U U|
         +-+-+-+-+-+-+-+-+

         U: Unused and for future use.  MUST be 0 on transmission and
         ignored on receipt.

   o  Tag: tag a packet as part of a class or group of packets, e.g.,
      packets sharing the same set of properties.  When tag is not used
      at source it MUST be set to zero on transmission.  When tag is not
      used during SRH Processing it SHOULD be ignored.  Tag is not used
      when processing the SID defined in Section 4.3.1.  It may be used
      when processing other SID types which are not defined in this
      document.  The allocation and use of tag is outside the scope of
      this document.

   o  Segment List[n]: 128 bit IPv6 addresses representing the nth
      segment in the Segment List.  The Segment List is encoded starting
      from the last segment of the SR Policy.  I.e., the first element
      of the segment list (Segment List [0]) contains the last segment
      of the SR Policy, the second element contains the penultimate
      segment of the SR Policy and so on.

   o  Type Length Value (TLV) are described in Section 2.1.

   In the SRH, the Next Header, Hdr Ext Len, and Routing Type fields are
   defined in Section 4.4 of [RFC8200] as not mutable.  The Segments
   Left field is defined as mutable in Section 4.4 of [RFC8200].

   Some of the other fields of the SRH change en route (i.e. they are
   mutable).  The SRH is processed as defined in Section 4.3 of this
   document, and uniquely per SID type.  The mutability of the remaining
   fields in the SRH (Flags, Tag, Segment List, Optional TLVs) are
   defined in that section, in the context of segment processing.

2.1.  SRH TLVs

   This section defines TLVs of the Segment Routing Header.

   A TLV provides meta-data for segment processing.  The only TLVs
   defined in this document are the HMAC (Section 2.1.2) and PAD
   (Section 2.1.1) TLVs.  While processing the SID defined in
   Section 4.3.1, all TLVs are ignored unless local configuration

Filsfils, et al.        Expires November 22, 2019               [Page 5]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   indicates otherwise (Section 4.3.1.1.1).  Thus, TLV and HMAC support
   is optional for any implementation, however an implementation adding
   or parsing TLVs MUST support PAD TLVs.  Other documents may define
   additional TLVs and processing rules for them.

   TLVs are present when the Hdr Ext Len exceeds the Last Entry element
   in the Segment List.

   While processing TLVs at a segment endpoint, TLVs MUST be fully
   contained within the SRH as determined by the Hdr Ext Len. Detection
   of TLVs exceeding the boundary of the SRH Hdr Ext Len results in an
   ICMP Parameter Problem, Code 0, message to the Source Address,
   pointing to the Hdr Ext Len field of the SRH, and the packet being
   discarded.

   An implementation MAY limit the number and/or length of TLVs it
   processes based on local configuration.  It MAY:

   o  Limit the number of consecutive Pad0 (Section 2.1.1.1) options to
      1, if padding of more than one byte is required then PadN
      (Section 2.1.1.2) should be used.

   o  Limit the length in PadN to 5.

   o  Limit the maximum number of non-Pad TLVs to be processed.

   o  Limit the maximum length of all TLVs to be processed.

   The implementation MAY stop processing additional TLVs in the SRH
   when these configured limits are exceeded.

    0                   1
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-----------------------
   |     Type      |    Length     | Variable length data
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-----------------------

   Type: An 8 bit value.  Unrecognized Types MUST be ignored on receipt.

   Length: The length of the Variable length data.

   Variable length data: Length bytes of data that is specific to the
   Type.

   Type Length Value (TLV) contain OPTIONAL information that may be used
   by the node identified in the Destination Address (DA) of the packet.

Filsfils, et al.        Expires November 22, 2019               [Page 6]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   Each TLV has its own length, format and semantic.  The code-point
   allocated (by IANA) to each TLV Type defines both the format and the
   semantic of the information carried in the TLV.  Multiple TLVs may be
   encoded in the same SRH.

   TLVs may change en route at each segment.  To identify when a TLV
   type may change en route the most significant bit of the Type has the
   following significance:

      0: TLV data does not change en route

      1: TLV data does change en route

   All TLVs specify their alignment requirements using an xn+y format.
   The xn+y format is defined as per [RFC8200].  The SR Source nodes use
   the xn+y alignment requirements of TLVs and padding TLVs when
   constructing an SRH.

   The "Length" field of the TLV is used to skip the TLV while
   inspecting the SRH in case the node doesn't support or recognize the
   Type.  The "Length" defines the TLV length in octets, not including
   the "Type" and "Length" fields.

   The following TLVs are defined in this document:

      Padding TLVs

      HMAC TLV

   Additional TLVs may be defined in the future.

2.1.1.  Padding TLVs

   There are two types of padding TLVs, pad0 and padN, the following
   applies to both:

      Padding TLVs are used to pad the SRH to a multiple of 8 octets.

      Padding TLVs are used for alignment.

      Padding TLVs are ignored by a node processing the SRH TLV.

      Multiple Padding TLVs MAY be used in one SRH

Filsfils, et al.        Expires November 22, 2019               [Page 7]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

2.1.1.1.  PAD0

   Alignment requirement: none

     0 1 2 3 4 5 6 7
     +-+-+-+-+-+-+-+-+
     |     Type      |
     +-+-+-+-+-+-+-+-+

      Type: to be assigned by IANA (Suggested value 0)

   A single Pad0 TLV MUST be used when a single byte of padding is
   required.  If more than one byte of padding is required a Pad0 TLV
   MUST NOT be used, the PadN TLV MUST be used.

2.1.1.2.  PADN

   Alignment requirement: none

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |    Length     |      Padding (variable)       |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   //                    Padding (variable)                       //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

      Type: to be assigned by IANA (suggested value 1).

      Length: 0 to 5

      Padding: Length octets of padding.  Padding bits have no
      semantics.  They MUST be set to 0 on transmission and ignored on
      receipt.

   The PadN TLV MUST be used when more than one byte of padding is
   required.

2.1.2.  HMAC TLV

   Alignment requirement: 8n

   The keyed Hashed Message Authentication Code (HMAC) TLV is OPTIONAL
   and has the following format:

Filsfils, et al.        Expires November 22, 2019               [Page 8]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

    0                   1                   2                   3
    0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |      Type     |     Length    |          RESERVED             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                      HMAC Key ID (4 octets)                   |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                              //
   |                      HMAC (32 octets)                        //
   |                                                              //
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   where:

   o  Type: to be assigned by IANA (suggested value 5).

   o  Length: 38.

   o  RESERVED: 2 octets.  MUST be 0 on transmission and ignored on
      receipt.

   o  HMAC Key ID: A 4 octet opaque number which uniquely identifies the
      pre-shared key and algorithm used to generate the HMAC.  If 0, the
      HMAC is not included.

   o  HMAC: 32 octets of keyed HMAC, not present if Key ID is 0.

   The HMAC TLV is used to verify the source of a packet is permitted to
   use the current segment in the destination address of the packet, and
   ensure the segment list is not modified in transit.

2.1.2.1.  HMAC Generation and Verification

   Local configuration determines when to check for an HMAC and
   potentially provides an alternate composition of Text, and a
   requirement on where the HMAC TLV must appear (e.g. first TLV), and
   whether or not to verify the destination address is equal to the
   current segment.  This local configuration is outside the scope of
   this document.  It may be based on the active segment at an SR
   Segment endpoint node, the result of an ACL that considers incoming
   interface, HMAC Key ID, or other packet fields.

   An implementation that supports the generation and verification of
   the HMAC SHOULD support the following default behavior as defined in
   the remainder of this section.

   The HMAC verification begins by checking the current segment is equal
   to the destination address of the IPv6 header, i.e.  destination

Filsfils, et al.        Expires November 22, 2019               [Page 9]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   address is equal to Segment List [Segments Left] and Segments Left is
   less than or equal to Last Segment+1.

   The HMAC field is the output of the HMAC computation as defined in
   [RFC2104], using:

   o  key: the pre-shared key identified by HMAC Key ID

   o  HMAC algorithm: identified by the HMAC Key ID

   o  Text: a concatenation of the following fields from the IPv6 header
      and the SRH, as it would be received at the node verifying the
      HMAC:

      *  IPv6 header: source address (16 octets)

      *  SRH: Last Entry (1 octet)

      *  SRH: Flags (1 octet)

      *  SRH: HMAC Key-id (4 octets)

      *  SRH: all addresses in the Segment List (variable octets)

   The HMAC digest is truncated to 32 octets and placed in the HMAC
   field of the HMAC TLV.

   For HMAC algorithms producing digests less than 32 octets, the digest
   is placed in the lowest order octets of the HMAC field.  Remaining
   octets MUST be set to zero.

   If HMAC verification is successful, the packet is forwarded to the
   next segment.

   If HMAC verification fails, an ICMP error message (parameter problem,
   error code 0, pointing to the HMAC TLV) SHOULD be generated (but rate
   limited) and SHOULD be logged.

2.1.2.2.  HMAC Pre-Shared Key Algorithm

   The HMAC Key ID field allows for the simultaneous existence of
   several hash algorithms (SHA-256, SHA3-256 ... or future ones) as
   well as pre-shared keys.

   The HMAC Key ID field is opaque, i.e., it has neither syntax nor
   semantic except as an identifier of the right combination of pre-
   shared key and hash algorithm, and except that a value of 0 means
   that there is no HMAC field.

Filsfils, et al.        Expires November 22, 2019              [Page 10]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   At the HMAC TLV verification node the Key ID uniquely identifies the
   pre-shared key and HMAC algorithm.

   At the HMAC TLV generating node the Key ID and destination address
   uniquely identify the pre-shared key and HMAC algorithm.  Utilizing
   the destination address with the Key ID allows for overlapping key
   IDs amongst different HMAC verification nodes.  The Text for the HMAC
   computation is set to the IPv6 header fields and SRH fields as they
   would appear at the verification node, not necessarily the same as
   the source node sending a packet with the HMAC TLV.

   Pre-shared key roll-over is supported by having two key IDs in use
   while the HMAC TLV generating node and verifying node converge to a
   new key.

   SRH implementations can support multiple hash functions but MUST
   implement SHA-2 [FIPS180-4] in its SHA-256 variant.

   The selection of pre-shared key and algorithm, and their distribution
   is outside the scope of this document, some options may include:

   o  in the configuration of the HMAC generating or verifying nodes,
      either by static configuration or any SDN oriented approach

   o  dynamically using a trusted key distribution protocol such as
      [RFC6407]

3.  SR Nodes

   There are different types of nodes that may be involved in segment
   routing networks: source SR nodes originate packets with a segment in
   the destination address of the IPv6 header, transit nodes that
   forward packets destined to a remote segment, and SR segment endpoint
   nodes that process a local segment in the destination address of an
   IPv6 header.

3.1.  Source SR Node

   A Source SR Node is any node that originates an IPv6 packet with a
   segment (i.e.  SRv6 SID) in the destination address of the IPv6
   header.  The packet leaving the source SR Node may or may not contain
   an SRH.  This includes either:

      A host originating an IPv6 packet.

      An SR domain ingress router encapsulating a received packet in an
      outer IPv6 header, followed by an optional SRH.

Filsfils, et al.        Expires November 22, 2019              [Page 11]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   The mechanism through which a segment in the destination address of
   the IPv6 header and the Segment List in the SRH, is derived is
   outside the scope of this document.

3.2.  Transit Node

   A transit node is any node forwarding an IPv6 packet where the
   destination address of that packet is not locally configured as a
   segment nor a local interface.  A transit node is not required to be
   capable of processing a segment nor SRH.

3.3.  SR Segment Endpoint Node

   A SR segment endpoint node is any node receiving an IPv6 packet where
   the destination address of that packet is locally configured as a
   segment or local interface.

4.  Packet Processing

   This section describes SRv6 packet processing at the SR source,
   Transit and SR segment endpoint nodes.

4.1.  Source SR Node

   A Source node steers a packet into an SR Policy.  If the SR Policy
   results in a segment list containing a single segment, and there is
   no need to add information to SRH flag or TLV, the DA is set to the
   single segment list entry and the SRH MAY be omitted.

   When needed, the SRH is created as follows:

      Next Header and Hdr Ext Len fields are set as specified in
      [RFC8200].

      Routing Type field is set as TBD (to be allocated by IANA,
      suggested value 4).

      The DA of the packet is set with the value of the first segment.

      The first element of the SRH Segment List is the ultimate segment.
      The second element is the penultimate segment and so on.

      The Segments Left field is set to n-1 where n is the number of
      elements in the SR Policy.

      The Last Entry field is set to n-1 where n is the number of
      elements in the SR Policy.

Filsfils, et al.        Expires November 22, 2019              [Page 12]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

      HMAC TLV may be set according to Section 7.

      The packet is forwarded toward the packet's Destination Address
      (the first segment).

4.1.1.  Reduced SRH

   When a source does not require the entire SID list to be preserved in
   the SRH, a reduced SRH may be used.

   A reduced SRH does not contain the first segment of the related SR
   Policy (the first segment is the one already in the DA of the IPv6
   header), and the Last Entry field is set to n-2 where n is the number
   of elements in the SR Policy.

4.2.  Transit Node

   As specified in [RFC8200], the only node allowed to inspect the
   Routing Extension Header (and therefore the SRH), is the node
   corresponding to the DA of the packet.  Any other transit node MUST
   NOT inspect the underneath routing header and MUST forward the packet
   toward the DA according to its IPv6 routing table.

   When a SID is in the destination address of an IPv6 header of a
   packet, it's routed through an IPv6 network as an IPv6 address.
   SIDs, or the prefix(es) covering SIDs, and their reachability may be
   distributed by means outside the scope of this document.  For
   example, [RFC5308] or [RFC5340] may be used to advertise a prefix
   covering the SIDs on a node.

4.3.  SR Segment Endpoint Node

   Without constraining the details of an implementation, the SR segment
   endpoint node creates Forwarding Information Base (FIB) entries for
   its local SIDs.

   When an SRv6-capable node receives an IPv6 packet, it performs a
   longest-prefix-match lookup on the packets destination address.  This
   lookup can return any of the following:

       A FIB entry that represents a locally instantiated SRv6 SID
       A FIB entry that represents a local interface, not locally
                                     instantiated as an SRv6 SID
       A FIB entry that represents a non-local route
       No Match

Filsfils, et al.        Expires November 22, 2019              [Page 13]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

4.3.1.  FIB Entry Is Locally Instantiated SRv6 SID

   This document, and section, defines a single SRv6 SID.  Future
   documents may define additional SRv6 SIDs.  In which case, the entire
   content of this section will be defined in that document.

   If the FIB entry represents a locally instantiated SRv6 SID, process
   the next header chain of the IPv6 header as defined in section 4 of
   [RFC8200].  Section 4.3.1.1 describes how to process an SRH,
   Section 4.3.1.2 describes how to process an upper layer header or no
   next header.

   Processing this SID type modifies the Segments Left and, if
   configured to process TLVs, it may modify the "variable length data"
   of TLV types that change en route.  Therefore Segments Left is
   mutable and TLVs that change en route are mutable.  The remainder of
   the SRH (Flags, Tag, Segment List, and TLVs that do not change en
   route) are immutable while processing this SID type.

4.3.1.1.  SRH Processing

Filsfils, et al.        Expires November 22, 2019              [Page 14]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   S01. When an SRH is processed {
   S02.   If Segments Left is equal to zero {
   S03.     Proceed to process the next header in the packet,
            whose type is identified by the Next Header field in
            the Routing header.
   S04.   }
   S05.   Else {
   S06.     If local configuration requires TLV processing {
   S07.       Perform TLV processing (see TLV Processing)
   S08.     }
   S09.     max_last_entry  =  ( Hdr Ext Len /  2 ) - 1
   S10.     If  ((Last Entry > max_last_entry) or
   S11.          (Segments Left is greater than (Last Entry+1)) {
   S12.       Send an ICMP Parameter Problem, Code 0, message to
              the Source Address, pointing to the Segments Left
              field, and discard the packet.
   S13.     }
   S14.     Else {
   S15.       Decrement Segments Left by 1.
   S16.       Copy Segment List[Segments Left] from the SRH to the
              destination address of the IPv6 header.
   S17.       If the IPv6 Hop Limit is less than or equal to 1 {
   S18.         Send an ICMP Time Exceeded -- Hop Limit Exceeded in
                Transit message to the Source Address and discard
                the packet.
   S19.       }
   S20.       Else {
   S21.         Decrement the Hop Limit by 1
   S22.         Resubmit the packet to the IPv6 module for transmission
                to the new destination.
   S23.       }
   S24.     }
   S25.   }
   S26. }

4.3.1.1.1.  TLV Processing

   Local configuration determines how TLVs are to be processed when the
   Active Segment is a local SID type defined in this document.  The
   definition of local configuration is outside the scope of this
   document.

   For illustration purpose only, two example local configurations that
   may be associated with a SID are provided below.

Filsfils, et al.        Expires November 22, 2019              [Page 15]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   Example 1:
   For any packet received from interface I2
     Skip TLV processing

   Example 2:
   For any packet received from interface I1
     If first TLV is HMAC {
       Process the HMAC TLV
     }
     Else {
       Discard the packet
     }

4.3.1.2.  Upper-layer Header or No Next Header

   When processing the Upper-layer header of a packet matching a FIB
   entry locally instantiated as an SRv6 SID type defined in this
   document.

   IF (Upper-layer Header is IPv4 or IPv6) and
       local configuration permits {
     Perform IPv6 decapsulation
     Resubmit the decapsulated packet to the IPv4 or IPv6 module
   }
   ELSE {
     Send an ICMP parameter problem message to the Source Address and
     discard the packet.  Error code (TBD by IANA) "SR Upper-layer
     Header Error", pointer set to the offset of the upper-layer
     header.
   }

   A unique error code allows an SR Source node to recognize an error in
   SID processing at an endpoint.

4.3.2.  FIB Entry is a Local Interface

   If the FIB entry represents a local interface, not locally
   instantiated as an SRv6 SID, the SRH is processed as follows:

      If Segments Left is zero, the node must ignore the Routing header
      and proceed to process the next header in the packet, whose type
      is identified by the Next Header field in the Routing Header.

      If Segments Left is non-zero, the node must discard the packet and
      send an ICMP Parameter Problem, Code 0, message to the packet's
      Source Address, pointing to the unrecognized Routing Type.

Filsfils, et al.        Expires November 22, 2019              [Page 16]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

4.3.3.  FIB Entry Is A Non-Local Route

   Processing is not changed by this document.

4.3.4.  FIB Entry Is A No Match

   Processing is not changed by this document.

5.  Intra SR Domain Deployment Model

   The use of the SIDs exclusively within the SR Domain and solely for
   packets of the SR Domain is an important deployment model.

   This enables the SR Domain to act as a single routing system.

   This section covers:

   o  securing the SR Domain from external attempt to use its SIDs

   o  SR Domain as a single system with delegation between components

   o  handling packets of the SR Domain

5.1.  Securing the SR Domain

   Nodes outside the SR Domain are not trusted: they cannot directly use
   the SID's of the domain.  This is enforced by two levels of access
   control lists:

   1.  Any packet entering the SR Domain and destined to a SID within
       the SR Domain is dropped.  This may be realized with the
       following logic, other methods with equivalent outcome are
       considered compliant:

       *  allocate all the SID's from a block S/s

       *  configure each external interface of each edge node of the
          domain with an inbound infrastructure access list (IACL) which
          drops any incoming packet with a destination address in S/s

       *  Failure to implement this method of ingress filtering exposes
          the SR Domain to source routing attacks as described and
          referenced in [RFC5095]

   2.  The distributed protection in #1 is complemented with per node
       protection, dropping packets to SIDs from source addresses
       outside the SR Domain.  This may be realized with the following

Filsfils, et al.        Expires November 22, 2019              [Page 17]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

       logic, other methods with equivalent outcome are considered
       compliant:

       *  assign all interface addresses from prefix A/a

       *  at node k, all SIDs local to k are assigned from prefix Sk/sk

       *  configure each internal interface of each SR node k in the SR
          Domain with an inbound IACL which drops any incoming packet
          with a destination address in Sk/sk if the source address is
          not in A/a.

5.2.  SR Domain as a single system with delegation among components

   All intra SR Domain packets are of the SR Domain.  The IPv6 header is
   originated by a node of the SR Domain, and is destined to a node of
   the SR Domain.

   All inter domain packets are encapsulated for the part of the packet
   journey that is within the SR Domain.  The outer IPv6 header is
   originated by a node of the SR Domain, and is destined to a node of
   the SR Domain.

   As a consequence, any packet within the SR Domain is of the SR
   Domain.

   The SR Domain is a system in which the operator may want to
   distribute or delegate different operations of the outer most header
   to different nodes within the system.

   An operator of an SR domain may choose to delegate SRH addition to a
   host node within the SR domain, and validation of the contents of any
   SRH to a more trusted router or switch attached to the host.
   Consider a top of rack switch (T) connected to host (H) via interface
   (I).  H receives an SRH (SRH1) with a computed HMAC via some SDN
   method outside the scope of this document.  H classifies traffic it
   sources and adds SRH1 to traffic requiring a specific SLA.  T is
   configured with an IACL on I requiring verification of the SRH for
   any packet destined to the SID block of the SR Domain (S/s).  T
   checks and verifies that SRH1 is valid, contains an HMAC TLV and
   verifies the HMAC.

   An operator of the SR Domain may choose to have all segments in the
   SR Domain verify the HMAC.  This mechanism would verify that the SRH
   segment list is not modified while traversing the SR Domain.

Filsfils, et al.        Expires November 22, 2019              [Page 18]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

5.3.  MTU Considerations

   Within the SR Domain, well known mitigation techniques are
   RECOMMENDED, such as deploying a greater MTU value within the SR
   Domain than at the ingress edges.

5.4.  ICMP Error Processing

   ICMP error packets generated within the SR Domain are sent to source
   nodes within the SR Domain.  The invoking packet in the ICMP error
   message may contain an SRH.  Since the destination address of a
   packet with an SRH changes as each segment is processed, it may not
   be the destination used by the socket or application that generated
   the invoking packet.

   For the source of an invoking packet to process the ICMP error
   message, the correct destination address must be determined.  The
   following logic is used to determine the destination address for use
   by protocol error handlers.

   o  Walk all extension headers of the invoking IPv6 packet to the
      routing extension header preceding the upper layer header.

      *  If routing header is type 4 (SRH)

         +  Use the 0th segment in the segment list as the destination
            address of the invoking packet.

   ICMP errors are then processed by upper layer transports as defined
   in [RFC4443].

   For IP packets encapsulated in an outer IPv6 header, ICMP error
   handling is as defined in [RFC2473].

5.5.  Load Balancing and ECMP

   For any inter domain packet, the SR Source node MUST impose a flow
   label computed based on the inner packet.  The computation of the
   flow label is as recommended in [RFC6438] for the sending Tunnel End
   Point.

   For any intra domain packet, the SR Source node SHOULD impose a flow
   label computed as described in [RFC6437] to assist ECMP load
   balancing at transit nodes incapable of computing a 5-tuple beyond
   the SRH.

   At any transit node within an SR domain, the flow label MUST be used
   as defined in [RFC6438] to calculate the ECMP hash toward the

Filsfils, et al.        Expires November 22, 2019              [Page 19]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   destination address.  If flow label is not used, the transit node
   would likely hash all packets between a pair of SR Edge nodes to the
   same link.

   At an SR segment endpoint node, the flow label MUST be used as
   defined in [RFC6438] to calculate any ECMP hash used to forward the
   processed packet to the next segment.

5.6.  Other Deployments

   Other deployment models and their implications on security, MTU,
   HMAC, ICMP error processing and interaction with other extension
   headers are outside the scope of this document.

6.  Illustrations

   This section provides illustrations of SRv6 packet processing at SR
   source, transit and SR segment endpoint nodes.

6.1.  Abstract Representation of an SRH

   For a node k, its IPv6 address is represented as Ak, its SRv6 SID is
   represented as Sk.

   IPv6 headers are represented as the tuple of (source, destination).
   For example, a packet with source address A1 and destination address
   A2 is represented as (A1,A2).  The payload of the packet is omitted.

   An SR Policy is a list of segments.  A list of segments is
   represented as <S1,S2,S3> where S1 is the first SID to visit, S2 is
   the second SID to visit and S3 is the last SID to visit.

   (SA,DA) (S3, S2, S1; SL) represents an IPv6 packet with:

   o  Source Address is SA, Destination Addresses is DA, and next-header
      is SRH.

   o  SRH with SID list <S1, S2, S3> with SegmentsLeft = SL.

   o  Note the difference between the <> and () symbols.  <S1, S2, S3>
      represents a SID list where the leftmost segment is the first
      segment.  Whereas, (S3, S2, S1; SL) represents the same SID list
      but encoded in the SRH Segment List format where the leftmost
      segment is the last segment.  When referring to an SR policy in a
      high-level use-case, it is simpler to use the <S1, S2, S3>
      notation.  When referring to an illustration of detailed behavior,
      the (S3, S2, S1; SL) notation is more convenient.

Filsfils, et al.        Expires November 22, 2019              [Page 20]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   At its SR Policy headend, the Segment List <S1,S2,S3> results in SRH
   (S3,S2,S1; SL=2) represented fully as:

       Segments Left=2
       Last Entry=2
       Flags=0
       Tag=0
       Segment List[0]=S3
       Segment List[1]=S2
       Segment List[2]=S1

6.2.  Example Topology

   The following topology is used in examples below:

           + * * * * * * * * * * * * * * * * * * * * +

           *         [8]                [9]          *
                      |                  |
           *          |                  |           *
   [1]----[3]--------[5]----------------[6]---------[4]---[2]
           *          |                  |           *
                      |                  |
           *          |                  |           *
                      +--------[7]-------+
           *                                         *

           + * * * * * * *  SR Domain  * * * * * * * +

                                 Figure 3

   o  3 and 4 are SR Domain edge routers

   o  5, 6, and 7 are all SR Domain routers

   o  8 and 9 are hosts within the SR Domain

   o  1 and 2 are hosts outside the SR Domain

   o  The SR domain is secured as per Section 5.1 and no external packet
      can enter the domain with a destination address equal to a segment
      of the domain.

6.3.  Source SR Node

Filsfils, et al.        Expires November 22, 2019              [Page 21]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

6.3.1.  Intra SR Domain Packet

   When host 8 sends a packet to host 9 via an SR Policy <S7,A9> the
   packet is

   P1: (A8,S7)(A9,S7; SL=1)

6.3.1.1.  Reduced Variant

   When host 8 sends a packet to host 9 via an SR Policy <S7,A9> and it
   wants to use a reduced SRH, the packet is

   P2: (A8,S7)(A9; SL=1)

6.3.2.  Inter SR Domain Packet - Transit

   When host 1 sends a packet to host 2, the packet is

   P3: (A1,A2)

   The SR Domain ingress router 3 receives P3 and steers it to SR Domain
   egress router 4 via an SR Policy <S7, S4>.  Router 3 encapsulates the
   received packet P3 in an outer header with an SRH.  The packet is

   P4: (A3, S7)(S4, S7; SL=1)(A1, A2)

   If the SR Policy contains only one segment (the egress router 4), the
   ingress Router 3 encapsulates P3 into an outer header (A3, S4).  The
   packet is

   P5: (A3, S4)(A1, A2)

6.3.2.1.  Reduced Variant

   The SR Domain ingress router 3 receives P3 and steers it to SR Domain
   egress router 4 via an SR Policy <S7, S4>.  If router 3 wants to use
   a reduced SRH, Router 3 encapsulates the received packet P3 in an
   outer header with a reduced SRH.  The packet is

   P6: (A3, S7)(S4; SL=1)(A1, A2)

6.3.3.  Inter SR Domain Packet - Internal to External

   When host 8 sends a packet to host 1, the packet is encapsulated for
   the portion of its journey within the SR Domain.  From 8 to 3 the
   packet is

   P7: (A8,S3)(A8,A1)

Filsfils, et al.        Expires November 22, 2019              [Page 22]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   In the opposite direction, the packet generated from 1 to 8 is

   P8: (A1,A8)

   At node 3 P8 is encapsulated for the portion of its journey within
   the SR domain, with the outer header destined to segment S8.
   Resulting in

   P9: (A3,S8)(A1,A8)

   At node 8 the outer IPv6 header is removed by S8 processing, then
   processed again when received by A8.

6.4.  Transit Node

   Nodes 5 acts as transit nodes for packet P1, and sends packet

   P1: (A8,S7)(A9,S7;SL=1)

   on the interface toward node 7.

6.5.  SR Segment Endpoint Node

   Node 7 receives packet P1 and, using the logic in Section 4.3.1,
   sends packet

   P7: (A8,A9)(A9,S7; SL=0)

   on the interface toward router 6.

6.6.  Delegation of Function with HMAC Verification

   This section describes how a function may be delegated within the SR
   Domain to non SR source nodes.  In the following sections consider a
   host 8 connected to a top of rack 5.

6.6.1.  SID List Verification

   An operator may prefer to add the SRH at source 8, while 5 verifies
   the SID list is valid.

   For illustration purpose, an SDN controller provides 8 an SRH
   terminating at node 9, with segment list <S5,S7,S6,A9>, and HMAC TLV
   computed for the SRH.  The HMAC key is shared with 5, node 8 does not
   know the key.  Node 5 is configured with an IACL applied to the
   interface connected to 8, requiring HMAC verification for any packet
   destined to S/s.

Filsfils, et al.        Expires November 22, 2019              [Page 23]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   Node 8 originates packets with the received SRH with HMAC TLV.

   P15:(A8,S5)(A9,S6,S7,S5;SL=3;HMAC)

   Node 5 receives and verifies the HMAC for the SRH, then forwards the
   packet to the next segment

   P16:(A8,S7)(A9,S6,S7,S5;SL=2;HMAC)

   Node 6 receives

   P17:(A8,S6)(A9,S6,S7,S5;SL=1;HMAC)

   Node 9 receives

   P18:(A8,A9)(A9,S6,S7,S5;SL=0;HMAC)

   This use of an HMAC is particularly valuable within an enterprise
   based SR Domain [SRN].

7.  Security Considerations

   This section reviews security considerations related to the SRH,
   given the SRH processing and deployment models discussed in this
   document.

   As described in Section 5, it is necessary to filter packets ingress
   to the SR Domain, destined to SIDs within the SR Domain (i.e.,
   bearing a SID in the destination address).  This ingress filtering is
   via an IACL at SR Domain ingress border nodes.  Additional protection
   is applied via an IACL at each SR Segment Endpoint node, filtering
   packets not from within the SR Domain, destined to SIDs in the SR
   Domain.  ACLs are easily supported for small numbers of prefixes,
   making summarization important, and when the prefixes requiring
   filtering is kept to a seldom changing set.

   Additionally, ingress filtering of IPv6 source addresses as
   recommended in BCP38 SHOULD be used.

7.1.  Source Routing Attacks

   [RFC5095] deprecates the Type 0 Routing header due to a number of
   significant attacks that are referenced in that document.  Such
   attacks include bypassing filtering devices, reaching otherwise
   unreachable Internet systems, network topology discovery, bandwidth
   exhaustion, and defeating anycast.

Filsfils, et al.        Expires November 22, 2019              [Page 24]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   Because this document specifies that the SRH is for use within an SR
   domain protected by ingress filtering via IACLs; such attacks cannot
   be mounted from outside an SR Domain.  As specified in this document,
   SR Domain ingress edge nodes drop packets entering the SR Domain
   destined to segments within the SR Domain.

   Additionally, this document specifies the use of IACL on SR Segment
   Endpoint nodes within the SR Domain to limit the source addresses
   permitted to send packets to a SID in the SR Domain.

   Such attacks may, however, be mounted from within the SR Domain, from
   nodes permitted to source traffic to SIDs in the domain.  As such,
   these attacks and other known attacks on an IP network (e.g.  DOS/
   DDOS, topology discovery, man-in-the-middle, traffic interception/
   siphoning), can occur from compromised nodes within an SR Domain.

7.2.  Service Theft

   Service theft is defined as the use of a service offered by the SR
   Domain by a node not authorized to use the service.

   Service theft is not a concern within the SR Domain as all SR Source
   nodes and SR segment endpoint nodes within the domain are able to
   utilize the services of the Domain.  If a node outside the SR Domain
   learns of segments or a topological service within the SR domain,
   IACL filtering denies access to those segments.

7.3.  Topology Disclosure

   The SRH is unencrypted and may contain SIDs of some intermediate SR-
   nodes in the path towards the destination within the SR Domain.  If
   packets can be snooped within the SR Domain, the SRH may reveal
   topology, traffic flows, and service usage.

   This is applicable within an SR Domain but the disclosure is less
   relevant as an attacker has other means of learning topology, flows,
   and service usage.

7.4.  ICMP Generation

   The generation of ICMPv6 error messages may be used to attempt
   denial-of-service attacks by sending an error-causing destination
   address or SRH in back-to-back packets.  An implementation that
   correctly follows Section 2.4 of [RFC4443] would be protected by the
   ICMPv6 rate-limiting mechanism.

Filsfils, et al.        Expires November 22, 2019              [Page 25]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

7.5.  Applicability of AH

   The SR Domain is a trusted domain, as defined in [RFC8402] Section 2
   and Section 8.2.  The SR Source is trusted to add an SRH (optionally
   verified via the HMAC TLV in this document), and segments advertised
   within the domain are trusted to be accurate and advertised by
   trusted sources via a secure control plane.  As such the SR Domain
   does not rely on the Authentication Header (AH) as defined in
   [RFC4302] to secure the SRH.

   The use of SRH with AH by an SR source node, and processing at a SR
   segment endpoint node, is not defined in this document.  Future
   documents may define use of SRH with AH and its processing.

8.  IANA Considerations

   This document makes the following registrations in the Internet
   Protocol Version 6 (IPv6) Parameters "Routing Type" registry
   maintained by IANA:

   Suggested            Description             Reference
     Value
   ----------------------------------------------------------
      4         Segment Routing Header (SRH)    This document

   This section provides guidance to the Internet Assigned Numbers
   Authority (IANA) regarding registration of values related to the SRH,
   in accordance with BCP 26, [RFC8126].

   The following terms are used here with the meanings defined in BCP
   26: "namespace", "assigned value", "registration".

   The following policies are used here with the meanings defined in BCP
   26: "Private Use", "First Come First Served", "Expert Review",
   "Specification Required", "IETF Consensus", "Standards Action".

   For registration requests where a Designated Expert should be
   consulted, the responsible IESG area director should appoint the
   Designated Expert.  The intention is that any allocation will be
   accompanied by a published RFC.  In order to allow for the allocation
   of values prior to the RFC being approved for publication, the
   Designated Expert can approve allocations once it seems clear that an
   RFC will be published.  The Designated expert will post a request to
   the 6man WG mailing list (or a successor designated by the Area
   Director) for comment and review, including an Internet-Draft.
   Before a period of 30 days has passed, the Designated Expert will
   either approve or deny the registration request and publish a notice
   of the decision to the 6man WG mailing list or its successor, as well

Filsfils, et al.        Expires November 22, 2019              [Page 26]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   as informing IANA.  A denial notice must be justified by an
   explanation, and in the cases where it is possible, concrete
   suggestions on how the request can be modified so as to become
   acceptable should be provided.

8.1.  Segment Routing Header Flags Register

   This document requests the creation of a new IANA managed registry to
   identify SRH Flags Bits.  The registration procedure is "Expert
   Review" as defined in [RFC8126].  Suggested registry name is "Segment
   Routing Header Flags".  Flags is 8 bits.

8.2.  Segment Routing Header TLVs Register

   This document requests the creation of a new IANA managed registry to
   identify SRH TLVs.  The registration procedure is "Expert Review" as
   defined in [RFC8126].  Suggested registry name is "Segment Routing
   Header TLVs".  A TLV is identified through an unsigned 8 bit
   codepoint value, with assigned values 0-127 for TLVs that do not
   change en route, and 128-255 for TLVs that may change en route.  The
   following codepoints are defined in this document:

    Assigned      Description               Reference
     Value
   -----------------------------------------------------
      0           Pad0 TLV                  This document
      1           PadN TLV                  This document
      5           HMAC TLV                  This document

9.  Implementation Status

   This section is to be removed prior to publishing as an RFC.

   See [I-D.matsushima-spring-srv6-deployment-status] for updated
   deployment and interoperability reports.

9.1.  Linux

   Name: Linux Kernel v4.14

   Status: Production

   Implementation: adds SRH, performs END processing, supports HMAC TLV

   Details: https://irtf.org/anrw/2017/anrw17-final3.pdf and
   [I-D.filsfils-spring-srv6-interop]

Filsfils, et al.        Expires November 22, 2019              [Page 27]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

9.2.  Cisco Systems

   Name: IOS XR and IOS XE

   Status: Production (IOS XR), Pre-production (IOS XE)

   Implementation: adds SRH, performs END processing, no TLV processing

   Details: [I-D.filsfils-spring-srv6-interop]

9.3.  FD.io

   Name: VPP/Segment Routing for IPv6

   Status: Production

   Implementation: adds SRH, performs END processing, no TLV processing

   Details: https://wiki.fd.io/view/VPP/Segment_Routing_for_IPv6 and
   [I-D.filsfils-spring-srv6-interop]

9.4.  Barefoot

   Name: Barefoot Networks Tofino NPU

   Status: Prototype

   Implementation: performs END processing, no TLV processing

   Details: [I-D.filsfils-spring-srv6-interop]

9.5.  Juniper

   Name: Juniper Networks Trio and vTrio NPU's

   Status: Prototype & Experimental

   Implementation: SRH insertion mode, Process SID where SID is an
   interface address, no TLV processing

9.6.  Huawei

   Name: Huawei Systems VRP Platform

   Status: Production

   Implementation: adds SRH, performs END processing, no TLV processing

Filsfils, et al.        Expires November 22, 2019              [Page 28]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

10.  Contributors

   Kamran Raza, Zafar Ali, Brian Field, Daniel Bernier, Ida Leung, Jen
   Linkova, Ebben Aries, Tomoya Kosugi, Eric Vyncke, David Lebrun, Dirk
   Steinberg, Robert Raszuk, Dave Barach, John Brzozowski, Pierre
   Francois, Nagendra Kumar, Mark Townsley, Christian Martin, Roberta
   Maglione, James Connolly, Aloys Augustin contributed to the content
   of this document.

11.  Acknowledgements

   The authors would like to thank Ole Troan, Bob Hinden, Ron Bonica,
   Fred Baker, Brian Carpenter, Alexandru Petrescu, Punit Kumar Jaiswal,
   and David Lebrun for their comments to this document.

12.  References

12.1.  Normative References

   [FIPS180-4]
              National Institute of Standards and Technology, "FIPS
              180-4 Secure Hash Standard (SHS)", March 2012,
              <http://csrc.nist.gov/publications/fips/fips180-4/
              fips-180-4.pdf>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC2473]  Conta, A. and S. Deering, "Generic Packet Tunneling in
              IPv6 Specification", RFC 2473, DOI 10.17487/RFC2473,
              December 1998, <https://www.rfc-editor.org/info/rfc2473>.

   [RFC4302]  Kent, S., "IP Authentication Header", RFC 4302,
              DOI 10.17487/RFC4302, December 2005,
              <https://www.rfc-editor.org/info/rfc4302>.

   [RFC5095]  Abley, J., Savola, P., and G. Neville-Neil, "Deprecation
              of Type 0 Routing Headers in IPv6", RFC 5095,
              DOI 10.17487/RFC5095, December 2007,
              <https://www.rfc-editor.org/info/rfc5095>.

   [RFC6407]  Weis, B., Rowles, S., and T. Hardjono, "The Group Domain
              of Interpretation", RFC 6407, DOI 10.17487/RFC6407,
              October 2011, <https://www.rfc-editor.org/info/rfc6407>.

Filsfils, et al.        Expires November 22, 2019              [Page 29]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174,
              May 2017, <https://www.rfc-editor.org/info/rfc8174>.

   [RFC8200]  Deering, S. and R. Hinden, "Internet Protocol, Version 6
              (IPv6) Specification", STD 86, RFC 8200,
              DOI 10.17487/RFC8200, July 2017,
              <https://www.rfc-editor.org/info/rfc8200>.

   [RFC8402]  Filsfils, C., Ed., Previdi, S., Ed., Ginsberg, L.,
              Decraene, B., Litkowski, S., and R. Shakir, "Segment
              Routing Architecture", RFC 8402, DOI 10.17487/RFC8402,
              July 2018, <https://www.rfc-editor.org/info/rfc8402>.

12.2.  Informative References

   [I-D.filsfils-spring-srv6-interop]
              Filsfils, C., Clad, F., Camarillo, P., Abdelsalam, A.,
              Salsano, S., Bonaventure, O., Horn, J., and J. Liste,
              "SRv6 interoperability report", draft-filsfils-spring-
              srv6-interop-02 (work in progress), March 2019.

   [I-D.matsushima-spring-srv6-deployment-status]
              Matsushima, S., Filsfils, C., Ali, Z., and Z. Li, "SRv6
              Implementation and Deployment Status", draft-matsushima-
              spring-srv6-deployment-status-01 (work in progress), May
              2019.

   [RFC2104]  Krawczyk, H., Bellare, M., and R. Canetti, "HMAC: Keyed-
              Hashing for Message Authentication", RFC 2104,
              DOI 10.17487/RFC2104, February 1997,
              <https://www.rfc-editor.org/info/rfc2104>.

   [RFC4443]  Conta, A., Deering, S., and M. Gupta, Ed., "Internet
              Control Message Protocol (ICMPv6) for the Internet
              Protocol Version 6 (IPv6) Specification", STD 89,
              RFC 4443, DOI 10.17487/RFC4443, March 2006,
              <https://www.rfc-editor.org/info/rfc4443>.

   [RFC5308]  Hopps, C., "Routing IPv6 with IS-IS", RFC 5308,
              DOI 10.17487/RFC5308, October 2008,
              <https://www.rfc-editor.org/info/rfc5308>.

   [RFC5340]  Coltun, R., Ferguson, D., Moy, J., and A. Lindem, "OSPF
              for IPv6", RFC 5340, DOI 10.17487/RFC5340, July 2008,
              <https://www.rfc-editor.org/info/rfc5340>.

Filsfils, et al.        Expires November 22, 2019              [Page 30]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   [RFC6437]  Amante, S., Carpenter, B., Jiang, S., and J. Rajahalme,
              "IPv6 Flow Label Specification", RFC 6437,
              DOI 10.17487/RFC6437, November 2011,
              <https://www.rfc-editor.org/info/rfc6437>.

   [RFC6438]  Carpenter, B. and S. Amante, "Using the IPv6 Flow Label
              for Equal Cost Multipath Routing and Link Aggregation in
              Tunnels", RFC 6438, DOI 10.17487/RFC6438, November 2011,
              <https://www.rfc-editor.org/info/rfc6438>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, DOI 10.17487/RFC8126, June 2017,
              <https://www.rfc-editor.org/info/rfc8126>.

   [SRN]      Lebrun, D., Jadin, M., Clad, F., Filsfils, C., and O.
              Bonaventure, "Software Resolved Networks: Rethinking
              Enterprise Networks with IPv6 Segment Routing", 2018,
              <https://inl.info.ucl.ac.be/system/files/
              sosr18-final15-embedfonts.pdf>.

Authors' Addresses

   Clarence Filsfils (editor)
   Cisco Systems, Inc.
   Brussels
   BE

   Email: cfilsfil@cisco.com

   Darren Dukes (editor)
   Cisco Systems, Inc.
   Ottawa
   CA

   Email: ddukes@cisco.com

   Stefano Previdi
   Huawei
   Italy

   Email: stefano@previdi.net

Filsfils, et al.        Expires November 22, 2019              [Page 31]
Internet-Draft      IPv6 Segment Routing Header (SRH)           May 2019

   John Leddy
   Individual
   US

   Email: john@leddy.net

   Satoru Matsushima
   Softbank

   Email: satoru.matsushima@g.softbank.co.jp

   Daniel Voyer (editor)
   Bell Canada

   Email: daniel.voyer@bell.ca

Filsfils, et al.        Expires November 22, 2019              [Page 32]