Segment routing for SD-WAN paths over hybrid networks
draft-dunbar-sr-sdwan-over-hybrid-networks-05
The information below is for an old version of the document.
| Document | Type |
This is an older version of an Internet-Draft whose latest revision state is "Expired".
|
|
|---|---|---|---|
| Authors | Linda Dunbar , Mehmet Toy | ||
| Last updated | 2019-07-08 (Latest revision 2019-06-13) | ||
| RFC stream | (None) | ||
| Formats | |||
| Additional resources | |||
| Stream | Stream state | (No stream defined) | |
| Consensus boilerplate | Unknown | ||
| RFC Editor Note | (None) | ||
| IESG | IESG state | I-D Exists | |
| Telechat date | (None) | ||
| Responsible AD | (None) | ||
| Send notices to | (None) |
draft-dunbar-sr-sdwan-over-hybrid-networks-05
Network Working Group L. Dunbar
Internet Draft Futurewei
Intended status: Informational Mehmet Toy
Expires: January 8, 2020 Verizon
July 8, 2019
Segment routing for SD-WAN paths over hybrid networks
draft-dunbar-sr-sdwan-over-hybrid-networks-05
Abstract
This document describes a method for end-to-end (E2E) SD-WAN paths
to traverse specific list of underlay network segments, some of
which can be private networks which include SR enabled segments,
some of which can be the public IP networks that do not support SR,
to achieve the desired optimal E2E quality.
The method described in this draft uses the principle of segment
routing to enforce a SD-WAN path' head-end selected route traversing
through a list of specific nodes of multiple network segments
without requiring the nodes in each network segment to have the
intelligence (or maintaining states) of selecting next hop or next
domain.
Status of this Memo
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79.
This Internet-Draft is submitted in full conformance with the
provisions of BCP 78 and BCP 79. This document may not be modified,
and derivative works of it may not be created, except to publish it
as an RFC and to translate it into languages other than English.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
xxx, et al. Expires January 8, 2020 [Page 1]
Internet-Draft SD-WAN over hybrid networks July 2019
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as
reference material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html
This Internet-Draft will expire on January 8, 2009.
Copyright Notice
Copyright (c) 2019 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with
respect to this document. Code Components extracted from this
document must include Simplified BSD License text as described in
Section 4.e of the Trust Legal Provisions and are provided without
warranty as described in the Simplified BSD License.
Table of Contents
1. Introduction...................................................3
2. Definition of terms............................................4
3. Key Use Cases..................................................5
3.1. SD-WAN Path over LTE network and SR Domain................5
3.2. SD-WAN as Last Mile for Cloud DCs Access..................6
3.3. How & Why SR is useful for those use cases................7
4. Mechanism for SD-WAN path over one SR Domain and existing access
..................................................................8
4.1. Controller Delivers SID Stack to SD-WAN Head-end..........9
4.2. Using GRE Key or VXLAN ID to Differentiate Flows.........11
Dunbar, et al. [Page 2]
Internet-Draft SD-WAN over hybrid networks July 2019
4.3. Using UDP Source Port Number to Differentiate Flows......12
4.4. GRE Header Extension.....................................15
5. SD-WAN path over multiple SP managed domains..................16
5.1. When Both SP domains support SR..........................18
5.2. When SP-2 does not support SR............................18
5.3. When SP-1 and SP-2 don't want to share network information19
5.4. TLV to pass Metadata through SRv6 Domain.................19
6. Security Considerations.......................................20
7. IANA Considerations...........................................21
8. References....................................................21
8.1. Normative References.....................................21
8.2. Informative References...................................21
9. Acknowledgments...............................................23
1. Introduction
This document describes a method to enforce a SD-WAN path's head-end
selected route traversing through a list of specific nodes of
multiple network segments without requiring the nodes in each
network segments to have the intelligence (or maintaining states) of
selecting next hop or next segments. Those networks over which the
SD-WAN path traverse have at least one SR enabled network, and some
network segments (especially the last mile access portion) being
existing IP networks (such as existing IPv4, IPv6 or others).
SD-WAN, as described by ONUG (Open Network User Group) and [SDWAN-
Net2Cloud], is about pooling WAN bandwidth from multiple service
providers to get better WAN bandwidth management, visibility &
control.
Throughout this document, the term "Classic SD-WAN" refers to a pair
of CPEs in two locations aggregating N Service Providers' paths,
such as MPLS Paths and public internet paths. [SR-SD-WAN] describes
using explicit routes within the SRv6 or SR-MPLS enabled networks to
reach the desired quality for SD-WAN paths over the SRv6 or SR-MPLS
enabled networks respectively.
[BGP-SDWAN-Usage] describes three distinct SD-WAN scenarios from an
edge node's perspective:
Dunbar, et al. [Page 3]
Internet-Draft SD-WAN over hybrid networks July 2019
1) All traffic is encrypted over WAN ports, so that network
service providers can extend its existing VPN to reach sites only
reachable via third party untrusted networks (such as public
internet);
2) Edge node has some ports connected to VPNs over which traffic
can go natively without encryption and other ports to the public
Internet over which traffic are encrypted; or
3) VPN PEs adding Internet facing WAN ports to offload low
priority traffic when the VPN backbone paths/links are congested.
This document focuses on the scenario 1) above, where a SD-WAN path
is spanning over SR enabled networks and over public IP networks,
such as existing IPv4, LTE, etc. Under this scenario, the endpoints
of the SD-WAN path (e.g. the CPE devices, one or both) are not
directly attached to PEs of a SR domain.
The goal is to place as large portion as possible of the SD-WAN path
over a provider VPN to achieve more optimal transport quality, or
steering the SD-WAN path traversing specific ingress/egress PEs to
reach optimal cost, quality, regulatory or other reasons.
2. Definition of terms
Cloud DC: Off-Premises Data Centers that usually host applications
and workload owned by different organizations or
tenants.
Controller: Used interchangeably with SD-WAN controller to manage
SD-WAN overlay path creation/deletion and monitoring the
path conditions between two or more sites.
Dunbar, et al. [Page 4]
Internet-Draft SD-WAN over hybrid networks July 2019
DMVPN: Dynamic Multipoint Virtual Private Network. DMVPN is a
secure network that exchanges data between sites without
needing to pass traffic through an organization's
headquarter virtual private network (VPN) server or
router.
Heterogeneous Cloud: applications & workloads split among Cloud DCs
owned & managed by different Cloud Providers.
Hybrid Cloud: applications & workloads split between on-premises
Data centers and Cloud DCs. In this document Hybrid
Cloud also include heterogeneous cloud as well.
SD-WAN: Software Defined Wide Area Network, "SDWAN" refers to
the solutions of pooling WAN bandwidth from multiple
underlay networks to get better WAN bandwidth
management, visibility & control. When the underlay
networks are private, traffic can traverse without
additional encryption; when the underlay networks are
public, such as the Internet, some traffic needs to be
encrypted when traversing through (depending on user
provided policies).
SP: Network Service Provider
SR: Segment Routing
SR Domain: A domain that supports Segment Routing
VPC: Virtual Private Cloud. A service offered by many Cloud
DC operators to allocate a logically isolated cloud
resources, including computing, networking and storage.
3. Key Use Cases
3.1. SD-WAN Path over LTE network and SR Domain
MEF Cloud Service Architecture [MEF-Cloud] describes a use case of
network operators needing to use SD-WAN over LTE for the last mile
Dunbar, et al. [Page 5]
Internet-Draft SD-WAN over hybrid networks July 2019
access that they do not have physical infrastructure, as shown
below:
+********SD-WAN Overlay Path *********+
* *
* +------------+ *
* |SD-WAN Ctrl | *
* +===+------------+====+ *
* // \\ *
* // <---Overlay Path ---> \\ *
* +-+--+ +--+ +--+ +--+-+ *
***+ E1 |==|C1+--------+C4+==+ E2 |****+
A --+ | | | | | | +----Z
A2--+--||+ ++-+ ++-+ ++---+\---Z2
LTE || | | //
|| | SR +-+---+ +----+
|| | Network | C6 | |E3 |
|| | | |----| |
+===+-+---+ +-+---+ +----+
+ C3 |-------+
+---+-+
|
+---+-+
| E4 |
+-----+
-- Directly attached
== || Public Internet or LTE path
*** Overlay path
Figure 1: SD-WAN end points are attached to VPN via LTE
3.2. SD-WAN as Last Mile for Cloud DCs Access
Digital Transformation is propelling more and more enterprises to
move their workloads/Apps to cloud DCs that are geographically close
to their end users to improve end-to-end latency & overall user
experience, or to comply with local data protection regulations.
Conversely, workloads/Apps in those Cloud DCs can be easily shutdown
when their end users' geographic base changes.
Because of the ephemeral property of the selected Cloud DCs, an
enterprise or its network service provider may not have the direct
Dunbar, et al. [Page 6]
Internet-Draft SD-WAN over hybrid networks July 2019
links to the Cloud DCs that are optimal for hosting the enterprise's
specific workloads/Apps. Under those circumstances, SD-WAN is a very
flexible choice to interconnect the enterprise on-premises data
centers & branch offices to its desired Cloud DCs.
However, SD-WAN paths over public internet can have unpredictable
performance, especially over long distances and cross state/country
boundaries. Therefore, it is highly desirable to place as much as
possible the portion of SD-WAN paths over service provider VPN (e.g.
enterprise's existing VPN) that have guaranteed SLA and to minimize
the distance/segments over public internet.
Under this scenario, one or both of the SD-WAN end points may not
directly attached to the PEs of a SR Domain.
3.3. How & Why SR is useful for those use cases
Let us assume that the SD-WAN Controller is capable of computing
optimal paths between two end-points (e.g. E1<->E2 in the Figure 2),
either by communicating with the SR Domain controller/management-
system, or by other methods which is out of the scope of this
document.
When a SR domain has multiple PEs with ports facing the external
networks (such as the public internet or LTE termination), SD-WAN
paths can traverse the SR domain via different ingress/egress PEs
resulting in different E2E performance.
In the diagram below, E1 <-> E2 SD-WAN (most likely IPsec encrypted
tunnel) path can traverse C1 <-> C4, C1<->C6, C3<->C6, or C3<->C4
within the VPN. There are many flows (by different Apps) between E1
<-> E2. Some flows may need to traverse C1<->C4, others may need to
traverse C3<->C6 or other segments within the VPN, which are
determined by the SD-WAN controller based on the characteristics &
need of the Apps, such as cost, available bandwidth, latency, or
special functions only available at specific locations, etc.
Even with the same ingress/egress, some flows may need different
segments across the SR Domain. It is not practical, or even
possible, for PEs (e.g. C1, C2, C3 in this example) to determine
which Apps' flows should egress C4 or C6 where both C4&C6 can reach
E2.
Dunbar, et al. [Page 7]
Internet-Draft SD-WAN over hybrid networks July 2019
Segment Routing can be used to steer packets (or path) to traverse
the explicit egress node (C4 or C6), or explicit segments through
the SR Domain based on the SLA requested by the SD-WAN head-end
nodes.
+********SD-WAN Overlay Path *********+
* *
* +------------+ *
* |SD-WAN Ctrl | *
* +===+------------+====+ *
* // \\ *
* // <-- Overlay path----> \\ *
* +-+--+ ++-+ ++-+ +--+-+ *
***+ E1 |==|C1|--------|C4+==+ E2 |****+
A --+ | | | | | | +----Z
A2--+--+-+ ++-+ ++-+ ++---+\---Z2
LTE || | | //
|| | SR +-+---+ +----+
|| | Network | C6 | |E3 |
|| | | |- --| |
|| +-+---+ +-+---+ +----+
+==+ C3 |-------+
+---+-+
|
+---+-+
| E4 |
+-----+
-- Directly attached
== || Public Internet or LTE path
** Overlay path
Figure 2: SDWAN end points not directly attached to PEs of SR Domain
4. Mechanism for SD-WAN path over one SR Domain and existing access
This section describes the mechanism to enforce a SD-WAN path' head-
end selected route traversing through a list of specific nodes of
multiple network segments without requiring the nodes in each
network segment to have the intelligence (or maintaining states) of
selecting next hop or next domain.
There may be two approaches here:
Dunbar, et al. [Page 8]
Internet-Draft SD-WAN over hybrid networks July 2019
1) Controller installs the entire SID stack at E1.
2) Controller delivers to E1 a "Key" that the SR ingress PE can use
to map to the SID stack for the packets arriving at the SR Ingress
PE. Section 4.2 & 4.3 will describe how the "Key" is carried by the
packets.
The Approach 1) requires less processing at the SR Ingress PE nodes,
but only works if the remote CPEs are in the same administrative
domain as the SR domain. SR domain usually is not willing to expose
its internal binding SIDs to devices in different administration
domains. This approach also requires more changes to SD-WAN end
nodes and need more header bytes added to the packets when rd traversing through 3 party internet. Some SD-WAN nodes might not be
capable of supporting encapsulating packets with the SID stack.
The Approach 2) above requires SR Ingress PE nodes to map the "Key"
to the SID Stack and prepend the SID stack to the packets (Same
processing for other traffic except the mapping is from the received
"Key" carried in the payload).
4.1. Controller Delivers SID Stack to SD-WAN Head-end
This approach is straightforward.
E1 -------------------------- > SD-WAN controller
request for a SD-WAN path E1<->E2 with a specific SLA
E1 <-------------------------- SD-WAN controller
Reply with the Ingress PE Node ID or address
& the Binding SID.
Here is the packet header for SD-WAN Source Node to prepend to the
payload:
Dunbar, et al. [Page 9]
Internet-Draft SD-WAN over hybrid networks July 2019
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
IPv4 Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Version| IHL |Type of Service| Total Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Identification |Flags| Fragment Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Time to Live | Prot.=17(UDP) | Header Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SD-WAN Source IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SR Ingress PE IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
UDP Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Port = | Dest. Port = 4754/4755 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UDP Length | UDP Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
GRE Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C| |K|S| Reserved0 | Ver | Protocol Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Checksum (optional) | Reserved1 (Optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Key (For SR Ingress to map to its SID) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
To traverse SRv6 domain, SRv6 Header is appended after the GRE
header [SRv6-SRH]:
Dunbar, et al. [Page 10]
Internet-Draft SD-WAN over hybrid networks July 2019
To traverse MPLS-SR domain, a stack of MPLS labels is appended after
GRE Header [MPLS-SR].
4.2. Using GRE Key or VXLAN ID to Differentiate Flows
This section describes a method of SD-WAN head-end node using GRE
Key or VXLAN Network ID (VNI) to indicate the desired property for
specific flows between SD-WAN end-points (E1<->E2 in the figure
above): such as different desired routes through the SR Domain,
different egress PEs based on cost, performance or other factors.
It might be difficult or impossible for DiffServ bits carried by the
packets to describe those flow properties because there can be more
than what DiffServ bits can represent.
The SR Domain ingress can map the GRE key to different SID through
the SR Domain.
We assume that the SD-WAN Controller can determine which ingress PE
can lead to the optimal path between E1<->E2. It is beyond the scope
of this document on how SD-WAN controller computes the paths and how
& what SD-WAN controller communicates with the SR Domain controller.
Here is the sequence of the flow:
E1 -------------------------- > SD-WAN controller
request for a SD-WAN path E1<->E2 with a specific SLA
E1 <-------------------------- SD-WAN controller
Reply with the Ingress PE Node ID or address
& (the GRE Key or VXLAN ID).
Note: the GRE key (or VXLAN ID) from the SD-WAN controller is for
the ingress PEs to correlate desired Path with the list of SIDs to
prepend the packet across the SR domain.
When SD-WAN Controller get the E1<->E2 path request, it will
communicate with the VPN Controller to get the optimal Ingress PE
Dunbar, et al. [Page 11]
Internet-Draft SD-WAN over hybrid networks July 2019
Node ID (or IP address) and the GRE key (or VXLAN ID) to encapsulate
the original packets between E1 <-> E2 (assuming IPsec Tunnel mode
is used).
Upon receiving the GRE encapsulated packets, the provider ingress
Edge C1/C3 uses the GRE key (or VXLAN ID) to map to the pre-defined
(by the network controller) Binding SIDs, prepend the Binding SIDs
to the packets, and forward its desired paths across the provider
VPN.
Depending on how the SD-WAN path destination can be reached by the
egress PE, the egress PE has different processing procedure:
- If the destination of the SD-WAN path is directly attached to
the egress VPN PE node, the egress VPN PE decapsulates SR
header and forward the packets to SD-WAN path destination node,
such as the E2 in the figure above.
- If the destination of the SD-WAN path is IP reachable via IPv4
network from the egress VPN PE node, the egress VPN PE node
decapsulates SR header and forward the packets to SD-WAN path
destination node via its internet facing port to the SD-WAN
path destination (i.e. the E2 node in the figure above).
- If the SD-WAN path is traversing multiple domains owned by
different network operators, the egress PE processing is
described in the next session.
4.3. Using UDP Source Port Number to Differentiate Flows
[RFC8086] describes how to use GRE-in-UDP source port number as
entropy for better ECMP performance. When the remotely attached CPEs
is within very close proximity to the PEs, e.g. only one or two
hopes away like in LTE access, there is less issue if ECMP put all
flows with same traffic classifier into one path. Then, those UDP
numbers can also be used as a key to SR PE nodes to map to the
appropriate SID to the packets.
Same as RFC8086, UDP source port values used as a key for SR PEs to
map to appropriate SIDs SHOULD be chosen from the ephemeral port
range (49152-65535) [RFC8085].
Dunbar, et al. [Page 12]
Internet-Draft SD-WAN over hybrid networks July 2019
The GRE-in-UDP encapsulation format contains a UDP header [RFC768]
and a GRE header [RFC2890]. The format is shown as follow
(presented in bit order):
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
IPv4 Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Version| IHL |Type of Service| Total Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Identification |Flags| Fragment Offset |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Time to Live | Prot.=17(UDP) | Header Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SD-WAN Source IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SR Ingress PE IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
UDP Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Port = SIDs key Value | Dest. Port = 4754/4755 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UDP Length | UDP Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
GRE Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C| |K|S| Reserved0 | Ver | Protocol Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Checksum (optional) | Reserved1 (Optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Key (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 3: UDP + GRE Headers in IPv4
Dunbar, et al. [Page 13]
Internet-Draft SD-WAN over hybrid networks July 2019
Here is the GRE Header for IPv6 network, i.e. the SD-WAN Source SD-
WAN Destination, and SR PEs are all in IPv6 domain:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
IPv6 Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Version| Traffic Class | Flow Label |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Payload Length | NxtHdr=17(UDP)| Hop Limit |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ SD-WAN Source IPv6 Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ SR Domain Ingress PE IPv6 Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
UDP Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source Port = SIDs key value | Dest. Port = 4754/4755 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UDP Length | UDP Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Dunbar, et al. [Page 14]
Internet-Draft SD-WAN over hybrid networks July 2019
GRE Header:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C| |K|S| Reserved0 | Ver | Protocol Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Checksum (optional) | Reserved1 (Optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Key (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 4: GRE+UDP for IPv6
4.4. GRE Header Extension
A new protocol type can be added to the GRE header [RFC2890] to make
it easier for the SR PE to do the proper actions:
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C| Reserved0 | Ver | Protocol Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Checksum (optional) | Reserved1 (Optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The proposed GRE header will have the following format:
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|C| |K|S| Reserved0 | Ver | Protocol Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Checksum (optional) | Reserved1 (Optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Key (optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Sequence Number (Optional) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
New protocol type (value to be assigned by IANA):
Dunbar, et al. [Page 15]
Internet-Draft SD-WAN over hybrid networks July 2019
UDP-Key: Using UDP source port value as a Key for SR Ingress PE to
map to the appropriate SIDs.
GRE-KEY: Using GRE Key value as a key for SR ingress PE to map to
the appropriate SIDs
5. SD-WAN path over multiple SP managed domains
The following figure shows a SD-WAN Path E1<->E2 over two SP domains
which are interconnected by public internet.
Dunbar, et al. [Page 16]
Internet-Draft SD-WAN over hybrid networks July 2019
+********SD-WAN Overlay Path *************+
* *
* +------------+ *
* |SD-WAN Ctrl | *
* +===+------------+====E2/E3/E4.. *
* // *
* // *
* +-+--+ ++-+ ++-+ +--+-+ *
***+ E1 |==|C1+--------+C7+--+ E7 | *
A --+ | | | | | | + *
A2--+----+ ++-+ ++-+ ++---+ *
LTE || | SP1 | // *
+---+ SR +-+---+ +----+ *
+--------+ |C3 | Network | C4 | |E3 | *
| E4 | | | | |- --| | *
| | +---+-----+---+---+-+ +----+ *
+--------+=======+ C2 | || *
+---+-+ // *
// // *
+-+-+--------+--+-+ *
|D1 | |D4 | *
| | | | *
++--+ ++---+ *
| SP2 | *
| SR +--+--+ +-+--+
+--------+ | Network | D2 | |E2 +----Z
| E6 | | | +====+ +---Z2
| | +--+-----+ +-+---+LTE +----+
+-+--+-+-+-------+ D3 |-----+
+---+-+
-- Directly attached
== || Public Internet or LTE path
** Overlay path
Figure 5: SD-WAN path over two different SP domains
Dunbar, et al. [Page 17]
Internet-Draft SD-WAN over hybrid networks July 2019
Let's assume that the SP-1 domain's egress node for the SD-WAN path
E1<->E2 is C2, which can reach D1 or D4 of SP-2 via public IP
network (say IPv4 network).
Let's also assume that the optimal route for some flows over SD-WAN
path E1<->E2 are C1->C2->D1 and other flows are over C1->C2->D4 (out
of the scope of this document on how the path is calculated).
If SP-1 is SR enabled, the mechanism described in Section 4 is
applicable to the SD-WAN path source node E1 and the SP-1's ingress
PE (e.g. C1 or C3 in the figure).
However, the processing at egress node might be different depending
on how the SP-1's egress edges are connected to the SP-2's ingress
edge nodes.
5.1. When Both SP domains support SR
There may be three approaches here:
1) Controller installs the entire SID stack at E1, and the SID list
contains SID entries belong to both domains.
2) Controller delivers to E1 the SID stack that only for the first
domain, but delivers to C6 (egress node of first domain) the binding
SID of the second domain.
3) Controller delivers a "Key" to E1, which can be encoded as GRE
KEY or represented by the Source UDP port of the GRE encapsulation,
for Ingress PE of the first SR Domain to map to its own SID stack as
described in Section 4. The first SR Domain will reserve the "Key"
through its domain and pass the "Key" to the second SR domain. The
second SR Domain Ingress node will use the same method to map the
"Key" to its SID stack.
5.2. When SP-2 does not support SR
Under this circumstance (which can be caused by SP-2 not supporting
SR or not willing to share Binding SIDs to SP-1), if the packets
arriving at SP-1 egress node C6 do not have any metadata indicating
the types of encrypted payload, C6 does not really have much choice
Dunbar, et al. [Page 18]
Internet-Draft SD-WAN over hybrid networks July 2019
other than simply forwarding the packets to E2 via public IP
network. This way, the packets may or may not traverse through the
SP-2 domain. If the distance between C6 and E2 is far, the quality
of service can be unpredictable.
5.3. When SP-1 and SP-2 don't want to share network information
If SP-1's ingress node C1 can include the GRE KEY it receives from
E1 in the data packets' SR header, the SP-1's egress node can map
the Key to the SP-2's Ingress node and encapsulate the data packet
in a new GRE header destined towards the SP-2's Ingress node. Then
the SP-2's Ingress node can follow the procedure described in the
Section 4 to forward the data packets across its domain.
If the first SR Domain does not support adding metadata to carry the
"key" through its domain, the controller can deliver the "key" to
SP-1's egress node the same time as it delivers the key to E1,
knowing the SD-WAN path will need to traverse two domains with the
second one does support SR but the two SPs don't want to exchange
network information.
5.4. TLV to pass Metadata through SRv6 Domain
If SP-1 is SRv6 based, the ingress node C1 can append a TLV to the
end of the SR Header [SRv6-SRH] to carry the KEY it receives from
E1.
The SP-1 egress node C6 can get the mapping between the KEYs and the
Node-IDs (or Addresses) of the next domain's ingress edge node (i.e.
D1 or D4 in the figure 3 above) from its network controller ahead of
time.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | RESERVED |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Key ID (4 octets) from the GRE tunnel remote ingress node |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Optional //
| Node ID or address for the ingress node Next domain //
| Variable length (0~32 octets) //
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Dunbar, et al. [Page 19]
Internet-Draft SD-WAN over hybrid networks July 2019
TYPE: (to be assigned by IANA) is to indicate the TLV is for
carrying the flow identifier of the packet encoded by the SD-WAN
source node.
Upon receiving the packet, the egress node (C6) can
- find the Node-ID (or the address) for the next domain's ingress
node,
- construct a GRE header with the Key received from the TLV above
and the destination address from the mapping given by the
controller,
- encapsulate the GRE header to the data packet (which has
decapsulated SR header),
- and forward the packet to the public internet.
6. Security Considerations
Remotely attached CPEs might brought the following security risks:
1) Potential DDoS attack to the PEs with ports facing internet.
I.e. the PE resource being attacked by unwanted traffic.
2) Potential risk of provider VPN network bandwidth being stolen
by the entities who spoofed the addresses of SD-WAN end nodes.
To mitigate security risk of 1) above, it is absolutely necessary
for PEs which accept remotely attached CPEs or simply have ports
facing internet to enable Anti-DDoS feature to prevent major DDoS
attack to those PEs.
To mitigate the security risk of 2) above, RFC7510 defines the use
of DTLS to authenticate and encrypt the RFC7510 encapsulation.
However, for the scenario of SD-WAN source node being remotely
attached to PEs, using the method recommended by RFC7510 means the
source node has to perform DTLS on top of the IPSec encryption
between SD-WAN end points E1<->E2. This can be too processing heavy
for the SD-WAN end nodes. In addition, if there are many SD-WAN
Dunbar, et al. [Page 20]
Internet-Draft SD-WAN over hybrid networks July 2019
flows to traverse through the ingress PE (e.g. C1, C2, C4 in the
figure 1 above), heavy processing is required on the ingress PEs.
Since the payload between E2<->E2 is already encrypted, the
confidentiality of the payload is already ensured. The network
operators need to balance between how much they can tolerant some
percentage of bandwidth being stolen and how much extra cost they
are willing to pay for completely prevent any unpaid traffic
traversing through its VPN networks. For operators who opt for lower
cost ingress PEs and CPEs, but can tolerant some percentage of
bandwidth being used by unpaid subscribers, a simple approach can be
considered:
- Embed a key in the packets, which can be changed periodically,
like the digital signature used by a certificate authority or
certification authority (CA).
- The key can be encoded in the GRE Key field between SD-WAN end
node and Ingress PE. Since GRE has 24 bits, some fixed bits
can be used to represent the signature of paid subscribers.
7. IANA Considerations
This document requires new protocol type:
Protocol type to be added to GRE header: SR_Route
8. References
8.1. Normative References
[RFC2890] G. Dommety "Key and Sequence Number Extensions to GRE".
Sep. 2000.
8.2. Informative References
[RFC2735] B. Fox, et al "NHRP Support for Virtual Private
networks". Dec. 1999.
Dunbar, et al. [Page 21]
Internet-Draft SD-WAN over hybrid networks July 2019
[RFC8192] S. Hares, et al "Interface to Network Security Functions
(I2NSF) Problem Statement and Use Cases", July 2017
[ITU-T-X1036] ITU-T Recommendation X.1036, "Framework for creation,
storage, distribution and enforcement of policies for
network security", Nov 2007.
[RFC6071] S. Frankel and S. Krishnan, "IP Security (IPsec) and
Internet Key Exchange (IKE) Document Roadmap", Feb 2011.
[RFC4364] E. Rosen and Y. Rekhter, "BGP/MPLS IP Virtual Private
Networks (VPNs)", Feb 2006
[RFC4664] L. Andersson and E. Rosen, "Framework for Layer 2 Virtual
Private Networks (L2VPNs)", Sept 2006.
[SR-SD-WAN] D. Dukes, et al, "SR for SDWAN: VPN with Underlay SLA",
draft-dukes-sr-for-sdwan-00, in progress, Oct 2017
[SRv6-SRH] S. Previdi, et al, "IPv6 Segment Routing Header (SRH)",
draft-ietf-6man-segment-routing-header-13, in progress,
April 2018.
[MPLS-SR] A. Bashandy, et al, "Segment Routing with MPLS data
plane", draft-ietf-spring-segment-routing-mpls-13, in
progress, April 2018.
[RFC7510] X. Xu, et al, "Encapsulating MPLS in UDP", April 2015.
[RFC8086] L. Yong, et al, "GRE-in-UDP Encapsulation", March 2017.
[BGP-SDWAN-Usage] L. Dunbar, et al, "BGP Usage for SDWAN Overlay
Networks, draft-dunbar-bess-bgp-sdwan-usage-01, in
progress, July 2019.
[SDWAN-Net2Cloud] L. Dunbar, et al, "Dynamic Networks to Hybrid
Cloud DCs Problem Statement", draft-ietf-rtgwg-net2cloud-
problem-statement-04, in progress, July 2019.
Dunbar, et al. [Page 22]
Internet-Draft SD-WAN over hybrid networks July 2019
[MEF-Cloud] "Cloud Services Architecture Technical Specification",
Work in progress, April 2018
9. Acknowledgments
Many thanks to Dean Cheng and Jim Guichard for the discussion and
contributions.
Dunbar, et al. [Page 23]
Internet-Draft SD-WAN over hybrid networks July 2019
Authors' Addresses
Linda Dunbar
Futurewei
Email: Linda.Dunbar@futurewei.com
Mehmet Toy
Verizon
One Verizon Way
Basking Ridge, NJ 07920
Email: mehmet.toy@verizon.com
Dunbar, et al. [Page 24]