IPv6 Socket API for Source Address Selection
draft-chakrabarti-ipv6-addrselect-api-07
The information below is for an old version of the document that is already published as an RFC.
| Document | Type |
This is an older version of an Internet-Draft that was ultimately published as RFC 5014.
|
|
|---|---|---|---|
| Authors | Samita Chakrabarti , Erik Nordmark , Julien Laganier | ||
| Last updated | 2015-10-14 (Latest revision 2007-06-18) | ||
| RFC stream | Internet Engineering Task Force (IETF) | ||
| Intended RFC status | Informational | ||
| Formats | |||
| Reviews | |||
| Stream | WG state | (None) | |
| Document shepherd | (None) | ||
| IESG | IESG state | Became RFC 5014 (Informational) | |
| Action Holders |
(None)
|
||
| Consensus boilerplate | Unknown | ||
| Telechat date | (None) | ||
| Responsible AD | Jari Arkko | ||
| Send notices to | ipv6-chairs@ietf.org |
draft-chakrabarti-ipv6-addrselect-api-07
Network Working Group E. Nordmark
Internet-Draft Sun Microsystems, Inc.
Intended status: Standards Track S. Chakrabarti
Expires: December 16, 2007 Azaire Networks
J. Laganier
DoCoMo Euro-Labs
June 14, 2007
IPv6 Socket API for Source Address Selection
draft-chakrabarti-ipv6-addrselect-api-07
Status of this Memo
By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
This Internet-Draft will expire on December 16, 2007.
Copyright Notice
Copyright (C) The IETF Trust (2007).
Nordmark, et al. Expires December 16, 2007 [Page 1]
Internet-Draft Socket API for Source Address Selection June 2007
Abstract
The IPv6 default address selection document [RFC3484] describes the
rules for selecting source and destination IPv6 addresses, and
indicates that applications should be able to reverse the sense of
some of the address selection rules through some unspecified API.
However, no such socket API exists in the basic [RFC3493] or advanced
[RFC3542] IPv6 socket API documents. This document fills that gap
partially by specifying new socket-level options for source address
selection and flags for the getaddrinfo() API to specify address
selection based on the the source address preference in accordance
with the socket-level options that modify the default source address
selection algorithm. The socket API described in this document will
be particularly useful for IPv6 applications that want to choose
between temporary and public addresses, and for Mobile IPv6 aware
applications that want to use the care-of address for communication.
It also specifies socket options and flags for selecting CGA or non-
CGA source addresses.
Nordmark, et al. Expires December 16, 2007 [Page 2]
Internet-Draft Socket API for Source Address Selection June 2007
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4
2. Definition Of Terms . . . . . . . . . . . . . . . . . . . . . 7
3. Usage Scenario . . . . . . . . . . . . . . . . . . . . . . . . 8
4. Design Alternatives . . . . . . . . . . . . . . . . . . . . . 9
5. Address Preference Flags . . . . . . . . . . . . . . . . . . . 10
6. Additions to the Socket Interface . . . . . . . . . . . . . . 12
7. Additions to the protocol-independent nodename translation . . 13
8. Application Requirements . . . . . . . . . . . . . . . . . . . 15
9. Usage Example . . . . . . . . . . . . . . . . . . . . . . . . 17
10. Implementation Notes . . . . . . . . . . . . . . . . . . . . . 18
11. Mapping to Default Address Selection Rules . . . . . . . . . . 19
12. IPv4-mapped IPv6 Addresses . . . . . . . . . . . . . . . . . . 21
13. Validating source address preferences . . . . . . . . . . . . 22
14. Summary of New Definitions . . . . . . . . . . . . . . . . . . 25
15. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 26
16. Security Considerations . . . . . . . . . . . . . . . . . . . 27
17. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 28
18. References . . . . . . . . . . . . . . . . . . . . . . . . . . 29
18.1. Normative references . . . . . . . . . . . . . . . . . . 29
18.2. Informative references . . . . . . . . . . . . . . . . . 29
Appendix A. Per Packet Address Selection Preference . . . . . . . 30
Appendix B. Changes from previous version of draft . . . . . . . 32
Appendix C. Intellectual Property Statement . . . . . . . . . . . 33
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 34
Intellectual Property and Copyright Statements . . . . . . . . . . 35
Nordmark, et al. Expires December 16, 2007 [Page 3]
Internet-Draft Socket API for Source Address Selection June 2007
1. Introduction
[RFC3484] specifies the default address selection rules for IPv6
[RFC2460]. This document defines socket API extensions that allow
applications to override the default choice of source address
selection. It therefore indirectly affects the destination address
selection through getaddrinfo(). Privacy considerations [RFC3041]
have introduced "public" and "temporary" addresses. IPv6 Mobility
[RFC3775] introduces "home address" and "care-of address" definitions
in the mobile systems.
The default address selection rules in [RFC3484] in summary are that
a public address is preferred over a temporary address, that a mobile
IPv6 home address is preferred over a care-of address, and that a
larger scope address is preferred over a smaller scope address.
Although it is desirable to have default rules for address selection,
an application may want to reverse certain address selection rules
for efficiency and other application-specific reasons.
Currently IPv6 socket API extensions provide mechanisms to choose a
specific source address through simple bind() operation or
IPV6_PKTINFO socket option [RFC3542]. However, in order to use
bind() or IPV6_PKTINFO socket option, the application itself must
make sure that the source address is appropriate for the destination
address (e.g., with respect to the interface used to send packets to
the destination). The application also needs to verify the
appropriateness of the source address scope with respect to the
destination address and so on. This can be quite complex for the
application, since in effect it needs to implement all the default
address selection rules in order to change its preferences with
respect to one of the rules.
The mechanism presented in this document allows the application to
specify attributes of the source addresses it prefers while still
having the system perform the rest of the address selection rules.
For instance, if an application specifies that it prefers to use a
care-of address over a home address as the source address and if the
host has two care-of addresses, one public and one temporary, then
the host would select the public care-of address by following the
default address selection rule for preferring a public over a
temporary address.
A socket option has been deemed useful for this purpose, as it
enables an application to specify address selection preferences on a
per-socket basis. It can also provide the flexibility of enabling
and disabling address selection preferences in non-connected (UDP)
sockets. The socket option uses a set of flags for specifying
address selection preferences. Since the API should not assume a
Nordmark, et al. Expires December 16, 2007 [Page 4]
Internet-Draft Socket API for Source Address Selection June 2007
particular implementation method of the address selection [RFC3484]
in the network layer or in getaddrinfo(), the corresponding set of
flags are also defined for getaddrinfo() as it depends on the source
address selection.
As a result, this document introduces several flags for address
selection preferences that alter the default address selection
[RFC3484] for a number of rules. It analyzes the usefulness of
providing API functionality for different default address selection
rules; it provides API to alter only those rules that are possibly
used by certain classes of applications. In addition, it also
considers CGA [RFC3972] and non-CGA source addresses when CGA
addresses are available in the system. In the future, more source
flags may be added to expand the API as the needs may arise.
The approach in this document is to allow the application to specify
preferences for address selection and not to be able to specify hard
requirements: For instance, an application can set a flag to prefer a
temporary source address, but if no temporary source addresses are
available at the node, a public address would be chosen instead.
Specifying hard requirements for address selection would be
problematic for several reasons. The major one is that in the vast
majority of cases the application would like to be able to
communicate even if an address with the 'optimal' attributes is not
available. For instance, an application that performs very short,
e.g., UDP, transactional exchanges (e.g. DNS queries), might prefer
to use a care-of address when running on a mobile host which is away
from home since this provides a short round-trip time in many cases.
But if the application is running on a mobile host that is at home,
or running on a host which isn't providing Mobile IPv6, then it
doesn't make sense for the application to fail due to no care-of
address being available. Also, in particular when using UDP sockets
and the sendto() or sendmsg() primitives, the use of hard
requirements would have been problematic, since the set of available
IP addresses might very well have changed from when the application
called getaddrinfo() until it called sendto() or sendmsg(), which
would introduce new failure modes.
For the few applications that have hard requirements on the
attributes of the IP addresses they use, this document defines a
verification function which allows such applications to properly fail
to communicate when their address selection requirements are not met.
Furthermore, the approach is to define two flags for each rule that
can be modified, so that an application can specify its preference
for addresses selected as per the rule, the opposite preference (i.e.
an address selected as per the rule reverted), or choose not to set
Nordmark, et al. Expires December 16, 2007 [Page 5]
Internet-Draft Socket API for Source Address Selection June 2007
either of the flags relating to that rule and leave it up to the
system default (section 4). This approach allows different
implementations to have different system defaults, and works with
getaddrinfo() as well as setsockopt(). (For setsockopt a different
approach could have been chosen, but that would still require the
same approach for getaddrinfo.)
Note that this document does not directly modify the destination
address selection rules described in [RFC3484]. An analysis has been
done to see which destination address rules may be altered by the
applications. Rule number 4(prefer home address), 8(prefer smaller
scope), 7(prefer native interfaces) of default address selection
document [RFC3484] were taken into consideration for destination
address alteration. But, as of this writing there was not enough
practical usage for applications to alter destination address
selection rules directly by applying the setsockopt() with a
preferred destination type of address flag. However, this document
does not rule out any possibility of adding flags for preferred
destination address selection. However, [RFC3484] destination
address selection rules are dependent on source address selections,
thus by altering the default source address selection by using the
methods described in this document, one indirectly influences the
choice of destination address selection. Hence this document
explains how getaddrinfo() can be used to select the destination
address while taking the preferred source addresses into
consideration [Section 11].
This document specifies extensions only to the Basic IPv6 socket API
specified in [RFC3493]. The intent is that this document serves as a
model for expressing preferences for attributes of IP addresses, that
also need to be expressible in other networking API such as those
found in middleware systems and the Java environment. Similar model
is also applicable for other socket families.
Nordmark, et al. Expires December 16, 2007 [Page 6]
Internet-Draft Socket API for Source Address Selection June 2007
2. Definition Of Terms
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [RFC2119].
Address preference flag:
A flag expressing a preference for a particular type of address
(e.g. temporary, public).
Opposite flags:
Each flag expressing an address preference has a so called
"opposite flag" expressing the opposite preference:
* home address preference flag is the opposite of the care-of
address preference flag.
* temporary address preference flag is the opposite of the public
address preference flag.
* CGA address preference flag is the opposite of the non-CGA
address preference flag.
Contradictory flags:
Any combination of flags including both a flag expressing a given
address preference and a flag expressing the opposite preference
constitutes Such flags are contradictory by definition of their
usefulness with respect to source address selection. For example,
consider a set of flags including both the home address preference
flag and the care-of address preference flag. When considering
source address selection, the selected address can be a home
address, or a care-of address, but it cannot be both at the same
time. Hence, to prefer an address which is both a home address,
and a care-of address, is contradictory.
Nordmark, et al. Expires December 16, 2007 [Page 7]
Internet-Draft Socket API for Source Address Selection June 2007
3. Usage Scenario
The examples discussed here are limited to applications supporting
Mobile IPv6, IPv6 Privacy Extensions and Cryptographically Generated
Addresses. Address selection document [RFC3484] recommends that home
addresses should be preferred over care-of address when both are
configured. However, a mobile node may want to prefer care-of
address as source address for DNS query in the foreign network as it
normally means a shorter and local return path compared to the route
via the mobile node's home-agent when the query contains home address
as source address. Another example is IKE application which requires
care-of address as its source address for the initial security
association pair with Home Agent [RFC3775] while the mobile node
boots up at the foreign network and wants to do the key exchange
before a successful home-registration. Also a Mobile IPv6 aware
application may want to toggle between home address and care-of
address depending on its location and state of the application. It
may also want to open different sockets and use home address as
source address for one socket and care-of address for the others.
In a non-mobile environment, an application may similarly prefer to
use temporary address as source address for certain cases. By
default, the source address selection rule selects "public" address
when both are available. For example, an application supporting web
browser and mail-server may want to use "temporary" address for the
former and "public" address for the mail-server as a mail-server may
require reverse path for DNS records for anti-spam rules.
Similarly, a node may be configured to use Cryptographically
Generated Addresses [RFC3972] by default, as in Secure Neighbor
Discovery [RFC3971], but an application may prefer not to use it.
For instance, fping [FPING], a debugging tool which tests basic
reachability of multiple destinations by sending packets in parallel.
These packets may end up initiating neighbor discovery signaling that
uses SEND if used with a CGA source address. SEND performs some
cryptographic operations to prove ownership of the said CGA address.
If the application does not require this feature, it would like to
use a non-CGA address to avoid potentially expensive computations
performed by SEND. On the other hand, when a node is not configured
for CGA as default, an application may prefer using CGA by setting
the corresponding preference.
Nordmark, et al. Expires December 16, 2007 [Page 8]
Internet-Draft Socket API for Source Address Selection June 2007
4. Design Alternatives
Some suggested to have per-application flags instead of per-socket
and per-packet flags. However, this design stays with per-socket and
per-packet flags for the following reasons:
o While some systems have per environment/application flags (such as
environment variables in Unix systems) this might not be available
in all systems which implement the socket API.
o When an application links with some standard library, that library
might use the socket API, while the application is unaware of that
fact. Mechanisms that would provide per application flags may
affect not only the application itself but also the libraries,
hence creating risks of unintended consequences.
Instead of the pair of 'flag' and 'opposite flag' for each rule that
can be modified, the socket option could have been defined to use a
single 'flag' value for each rule. This would still have allowed
different implementations to have different default settings as long
as the applications were coded to first retrieve the default setting
(using getsockopt()), and then clear or set the 'flag' according to
their preferences, and finally set the new value with setsockopt().
But such an approach would not be possible for getaddrinfo() because
all the preferences would need to be expressible in the parameters
that are passed with a single getaddrinfo() call. Hence, for
consistency, the 'flag' and 'opposite flag' approach is used for both
getaddrinfo() and setsockopt().
Thus in this API document, an application has three choices on source
address selection:
a) Application wants to use an address with flag X : Set flag X;
unset opposite/contradictory flags of X if they are set before.
b) Application wants to use an address with 'opposite' or
contradictory flag of X: Set opposite or contradictory flag of X;
unset flag X, if already set.
c) Application does not care about the presence of flag X and
would like to use default : No need to set any address preference
flags through setsockopt() or getaddrinfo() ; unset any address
preference flags if they are set before by the same socket.
Nordmark, et al. Expires December 16, 2007 [Page 9]
Internet-Draft Socket API for Source Address Selection June 2007
5. Address Preference Flags
The following flags are defined to alter or set the default rule of
source address selection rules discussed in default address selection
specification [RFC3484].
IPV6_PREFER_SRC_HOME /* Prefer Home address as source */
IPV6_PREFER_SRC_COA /* Prefer Care-of address as source */
IPV6_PREFER_SRC_TMP /* Prefer Temporary address as source */
IPV6_PREFER_SRC_PUBLIC /* Prefer Public address as source */
IPV6_PREFER_SRC_CGA /* Prefer CGA address as source */
IPV6_PREFER_SRC_NONCGA /* Prefer a non-CGA address as source */
These flags can be combined together in a flag-set to express more
complex address preferences. However such combinations can result in
a contradictory flag-set, for example:
IPV6_PREFER_SRC_PUBLIC | IPV6_PREFER_SRC_TMP
IPV6_PREFER_SRC_HOME | IPV6_PREFER_SRC_COA
IPV6_PREFER_SRC_HOME | IPV6_PREFER_SRC_COA | IPV6_PREFER_SRC_TMP
IPV6_PREFER_SRC_CGA | IPV6_PREFER_SRC_NONCGA
Etc.
Example of valid combination of address selection flags are given
below:
IPV6_PREFER_SRC_HOME | IPV6_PREFER_SRC_PUBLIC
IPV6_PREFER_SRC_HOME | IPV6_PREFER_SRC_CGA
IPV6_PREFER_SRC_COA | IPV6_PREFER_SRC_PUBLIC | IPV6_PREFER_SRC_CGA
IPV6_PREFER_SRC_HOME | IPV6_PREFER_SRC_NONCGA
If a flag-set includes a combination of 'X' and 'Y', and if 'Y' is
not applicable or available in the system, then the selected address
has attribute 'X' and system default for the attribute 'Y'. For
example, on a system that has only public addresses, the valid
combination of flags:
Nordmark, et al. Expires December 16, 2007 [Page 10]
Internet-Draft Socket API for Source Address Selection June 2007
IPV6_PREFER_SRC_TMP | IPV6_PREFER_SRC_HOME
would result in the selected address being a public home address,
since no temporary addresses are available.
Nordmark, et al. Expires December 16, 2007 [Page 11]
Internet-Draft Socket API for Source Address Selection June 2007
6. Additions to the Socket Interface
The IPv6 Basic Socket API [RFC3493] defines socket options for IPv6.
To allow applications to influence address selection mechanisms this
document adds a new socket option at the IPPROTO_IPV6 level. This
socket option is called IPV6_ADDR_PREFERENCES. It can be used with
setsockopt() and getsockopt() calls to set and get the address
selection preferences affecting all packets sent via a given socket.
The socket option value (optval) is a 32-bits unsigned integer
argument. The argument consists of a number of flags where each flag
indicates an address selection preference which modifies one of the
rules in the default address selection specification.
The following flags are defined to alter or set the default rule of
source address selection rules discussed in default address selection
specification [RFC3484]. They are defined as a result of including
the <netinet/in.h> header:
IPV6_PREFER_SRC_HOME /* Prefer Home address as source */
IPV6_PREFER_SRC_COA /* Prefer Care-of address as source */
IPV6_PREFER_SRC_TMP /* Prefer Temporary address as source */
IPV6_PREFER_SRC_PUBLIC /* Prefer Public address as source */
IPV6_PREFER_SRC_CGA /* Prefer CGA address as source */
IPV6_PREFER_SRC_NONCGA /* Prefer a non-CGA address as source */
NOTE: No source preference flag for longest matching prefix is
defined here because it is believed to be handled by the policy table
defined in the default address selection specification.
When the IPV6_ADDR_PREFERENCES is successfully set with setsockopt(),
the option value given is used to specify address preference for any
connection initiation through the socket and all subsequent packets
sent via that socket. If no option is set, the system selects a
default value as per default address selection algorithm or by some
other equivalent means.
Setting contradictory flags at the same time results in the error
EINVAL.
Nordmark, et al. Expires December 16, 2007 [Page 12]
Internet-Draft Socket API for Source Address Selection June 2007
7. Additions to the protocol-independent nodename translation
Section 8 of Default Address Selection [RFC3484] document indicates
possible implementation strategies for getaddrinfo() [RFC3493]. One
of them suggests that getaddrinfo() collects available source/
destination pair from the network layer after being sorted at the
network layer with full knowledge of source address selection.
Another strategy is to call down to the network layer to retrieve
source address information and then sort the list in the context of
getaddrinfo().
This implies that getaddrinfo() should be aware of the address
selection preferences of the application, since getaddrinfo() is
independent of any socket the application might be using.
Thus if an application alters the default address selection rules by
using setsockopt() with the IPV6_ADDR_PREFERENCES option, the
application should also use the corresponding address selection
preference flags with its getaddrinfo() call.
For that purpose, the addrinfo data structure defined in Basic IPV6
Socket API Extension [RFC3493] has been extended with an extended
"ai_eflags" flag-set field to provide the designers freedom of adding
more flags as necessary without crowding the valuable bit space in
the "ai_flags" flag-set field. The extended addrinfo data structre
is defined as a result of including the <netdb.h> header:
struct addrinfo {
int ai_flags; /* input flags */
int ai_family; /* protocol family for socket */
int ai_socktype; /* socket type */
int ai_protocol; /* protocol for socket */
socklen_t ai_addrlen; /* length of socket address */
char *ai_canonname; /* canonical name for hostname */
struct sockaddr *ai_addr; /* socket address for socket */
struct addrinfo *ai_next; /* pointer to next in list */
int ai_eflags; /* Extended flags for special usage */
};
Note that the additional field for extended flags are added at the
bottom of the addrinfo structure to preserve binary compatibility of
the new functionality with the old applications which use the
existing addrinfo data structure.
A new flag (AI_EXTFLAGS) is defined for the "ai_flags" flag-set field
of the addrinfo data structure to tell the system to look for the
"ai_eflags" extended flag-set field in the addrinfo structure. It is
defined in the <netdb.h> header:
Nordmark, et al. Expires December 16, 2007 [Page 13]
Internet-Draft Socket API for Source Address Selection June 2007
AI_EXTFLAGS /* extended flag-set present */
If AI_EXTFLAGS flag is set in "ai_flags" flag-set field of the
addrinfo data structure, then the getaddrinfo() implementation MUST
look for the "ai_eflags" values stored in the extended flag-set field
"ai_eflags" of the addrinfo data structure. The flags stored in the
"ai_eflags" field are only meaningful if the AI_EXTFLAGS flag is set
in the "ai_flags" flag-set field of the addrinfo data structure. By
default, AI_EXTFLAGS is not set in the "ai_flags" flag-set field. If
AI_EXTFLAGS is set in the "ai_flags" flag-set field, and the
"ai_eflags" extended flag-set field is 0 (zero) or undefined, then
AI_EXTFLAGS is ignored.
The IPV6 source address preference values (IPV6_PREFER_SRC_*) defined
for the IPV6_ADDR_PREFERENCES socket option are also defined as
address selection preference flags for the "ai_eflags" extended flag-
set field of the addrinfo data structure, so that getaddrinfo() can
return matching destination addresses corresponding to the source
address preferences expressed by the caller application.
Thus, an application passes source address selection hints to
getaddrinfo by setting AI_EXTFLAGS in the "ai_flags" field of the
addrinfo structure, and the corresponding address selection
preference flags (IPV6_PREFER_SRC_*) in the "ai_eflags" field.
Currently AI_EXTFLAGS is defined for the AF_INET6 socket protocol
family only. But its usage should be extendable to other socket
protocol families - such as AF_INET or as appropriate.
If contradictory flags such as IPV6_PREFER_SRC_HOME and
IPV6_PREFER_SRC_COA are set in ai_eflags, the getaddrinfo() fails and
return the value EAI_BADEXTFLAGS defined as a result of including the
<netdb.h> header. This error value MUST be interpreted into a
descriptive text string when passed to the gai_strerror() function
[RFC3493].
Nordmark, et al. Expires December 16, 2007 [Page 14]
Internet-Draft Socket API for Source Address Selection June 2007
8. Application Requirements
An application should call getsockopt() prior calling setsockopt() if
the application needs to be able to restore the socket back to the
system default preferences. Note, this is suggested for portability.
An application which does not have this requirement can just use
getaddrinfo() while specifying its preferences, followed by:
uint32_t flags = IPV6_PREFER_SRC_TMP;
if (setsockopt(s, IPPROTO_IPV6, IPV6_ADDR_PREFERENCES,
(void *) &flags, sizeof (flags)) == -1) {
perror("setsockopt IPV6_ADDR_REFERENCES");
}
An application which needs to be able to restore the default settings
on the socket would instead do this:
uint32_t save_flags, flags;
int optlen = sizeof (save_flags);
/* Save the existing IPv6_ADDR_PREFERENCE flags now */
if (getsockopt(s, IPPROTO_IPV6, IPV6_ADDR_PREFERENCES,
(void *) &save_flags, &optlen) == -1 {
perror("getsockopt IPV6_ADDR_REFERENCES");
}
/* Set the new flags */
flags = IPV6_PREFER_SRC_TMP;
if (setsockopt(s, IPPROTO_IPV6, IPV6_ADDR_PREFERENCES,
(void *) &flags, sizeof (flags)) == -1) {
perror("setsockopt IPV6_ADDR_REFERENCES");
}
/*
*
* Do some work with the socket here.
*
*/
/* Restore the flags */
if (setsockopt(s, IPPROTO_IPV6, IPV6_ADDR_PREFERENCES,
(void *) &save_flags, sizeof (save_flags)) == -1) {
perror("setsockopt IPV6_ADDR_REFERENCES");
}
Nordmark, et al. Expires December 16, 2007 [Page 15]
Internet-Draft Socket API for Source Address Selection June 2007
Applications should not set contradictory flags at the same time.
In order to allow different implementations to do different parts of
address selection in getaddrinfo() and in the protocol stack, this
specification requires that applications set the semantically
equivalent flags when calling getaddrinfo() and setsockopt(). For
example, if the application sets the IPV6_PREFER_SRC_COA flag, it
MUST use the same for the "ai_eflag" field of the addrinfo data
structure when calling getaddrinfo(). If applications are not
setting the semantically equivalent flags the behavior of the
implementation is undefined.
Nordmark, et al. Expires December 16, 2007 [Page 16]
Internet-Draft Socket API for Source Address Selection June 2007
9. Usage Example
An example of usage of this API is given below:
struct addrinfo hints, *ai, *ai0;
uint32_t preferences;
preferences = IPV6_PREFER_SRC_TMP;
hints.ai_flags |= AI_EXTFLAGS;
hints.ai_eflags = preferences; /* Chosen address preference flag */
/* Fill in other hints fields */
getaddrinfo(....,&hints,. &ai0..);
/* Loop over all returned addresses and do connect */
for (ai = ai0; ai; ai = ai->ai_next) {
s = socket(ai->ai_family, ...);
setsockopt(s, IPV6_ADDR_PREFERENCES, (void *) &preferences,
sizeof (preferences));
if (connect(s, ai->ai_addr, ai->ai_addrlen) == -1){
close (s);
s = -1;
continue;
}
break;
}
freeaddrinfo(ai0);
Nordmark, et al. Expires December 16, 2007 [Page 17]
Internet-Draft Socket API for Source Address Selection June 2007
10. Implementation Notes
o Within the same application, if a specific source address is set
by either bind() or IPV6_PKTINFO socket option, while at the same
time an address selection preference is expressed with the
IPV6_ADDR_PREFERENCES socket option, then the source address
setting carried by bind() or IPV6_PKTINFO takes precedence over
the address selection setting.
o setsockopt() and getaddrinfo() should silently ignore any address
preference flags that are not supported in the system. For
example, a host which does not implement Mobile IPv6, should not
fail setsockopt() or getaddrinfo() that specify preferences for
home or care-of addresses. The socket option calls should return
error (-1) and set errno to EINVAL when contradictory flags values
are passed to them.
o If an implementation supports both stream and datagram sockets, it
should implement the address preference mechanism API described in
this document on both types of sockets.
o An implementation supporting this API MUST implement both
getaddrinfo() extension flags and socket option flags processing
for portability of applications.
o The following flags are set as default values on a system (which
is consistent with [RFC3484] defaults):
IPV6_PREFER_SRC_HOME
IPV6_PREFER_SRC_PUBLIC
IPV6_PREFER_SRC_CGA
Nordmark, et al. Expires December 16, 2007 [Page 18]
Internet-Draft Socket API for Source Address Selection June 2007
11. Mapping to Default Address Selection Rules
This API defines only those flags that are deemed to be useful by the
applications to alter default address selection rules. Thus we
discuss the mapping of each set of flags to the corresponding rule
number in the address selection document [RFC3484].
Source address selection rule #4 (prefer home address):
IPV6_PREFER_SRC_HOME (default)
IPV6_PREFER_SRC_COA
Source address selection rule #7 (prefer public address) :
IPV6_PREFER_SRC_PUBLIC (default)
IPV6_PREFER_SRC_TMP
At this time, this document does not define flags to alter source
address selection rule #2 (prefer appropriate scope for destination)
and destination address selection rule #8 (prefer smaller scope) as
the implementers felt that there were no practical applications that
can take advantage of reverting the scoping rules of IPv6 default
address selection. Flags altering other destination address
selection rules (#4, prefer home address and #7, prefer native
transport) could have applications, but the problem is that the local
system cannot systematically determine whether a destination address
is a tunnel address for destination rule #7 (although it can when the
destination address is one of its own, or can be syntactically
recognized as a tunnel address, e.g., a 6to4 address.) The flags
defined for source address selection rule #4 (prefer home address)
should also take care of destination address selection rule #4. Thus
at this point, it was decided not to define flags for these
destination rules.
Also, note that there is no corresponding destination address
selection rule for source address selection rule #7 (prefer public
addresses) of default address selection document [RFC3484]. However,
this API provides a way for an application to make sure that the
source address preference set in setsockopt() is taken into account
by the getaddrinfo() function. Let's consider an example to
understand this scenario. DA and DB are two global destination
addresses and the node has two global source addresses SA and SB
through interface A and B respectively. SA is a temporary address
while SB is a public address. The application has set
IPV6_PREFER_SRC_TMP in the setsockopt() flag. The route to DA points
to interface A and route to DB points to interface B. Thus when
Nordmark, et al. Expires December 16, 2007 [Page 19]
Internet-Draft Socket API for Source Address Selection June 2007
AI_EXTFLAGS in ai_flags and IPV6_PREFER_SRC_TMP in ai_eflags are set,
getaddrinfo() returns DA before DB in the list of destination
addresses and thus SA will be used to communicate with the
destination DA. Similarly, getaddrinfo() returns DB before DA when
AI_EXTFLAGS and ai_eflags are set to IPV6_PREFER_SRC_PUBLIC. Thus
the source address preference is taking effect into destination
address selection and as well as source address selection by the
getaddrinfo() function.
The following numerical example clarifies the above further.
Imagine a host with two addresses:
1234::1:1 public
9876::1:2 temporary
The destination has the following two addresses:
1234::9:3
9876::9:4
By default getaddrinfo() will return the destination addresses in the
order
1234::9:3
9876::9:4
because the public source is preferred and 1234 matches more bits
with the public source address. On the other hand, if ai_flags is
set to AI_EXTFLAGS and ai_eflags to IPV6_PREFER_SRC_TMP, getaddrinfo
will return the addresses in the reverse order since the temporary
source address will be preferred.
Other source address rules (that are not mentioned here) were also
deemed not applicable for changing its default on a per-application
basis.
Nordmark, et al. Expires December 16, 2007 [Page 20]
Internet-Draft Socket API for Source Address Selection June 2007
12. IPv4-mapped IPv6 Addresses
IPv4-mapped IPv6 addresses for AF_INET6 sockets are supported in this
API. In some cases the application of IPv4-mapped addresses are
limited because the API attributes are IPv6 specific. For example,
IPv6 temporary addresses and cryptographically generated addresses
have no IPv4 counterparts. Thus the IPV6_PREFER_SRC_TMP or
IPV6_PREFER_SRC_CGA are not directly applicable to an IPv4-mapped
IPv6 address. However, the IPv4-mapped address support may be useful
for mobile-IPv4 applications shifting source address between the home
address and the care-of address. Thus the IPV6_PREFER_SRC_COA and
IPV6_PREFER_SRC_HOME are applicable to an IPv4-mapped IPv6 address.
At this point it is not well understood whether this particular API
has any value to IPv4 addresses or AF_INET family of sockets, but
similar model still applies to AF_INET socket family if corresponding
address flags are defined.
Nordmark, et al. Expires December 16, 2007 [Page 21]
Internet-Draft Socket API for Source Address Selection June 2007
13. Validating source address preferences
Sometimes an application may have a requirement to only use addresses
with some particular attribute, and if no such address is available
the application should fail to communicate instead of communicating
using the 'wrong' address. In that situation, address selection
preferences do not guarantee that the application requirements are
met. Instead, the application has to use a new call that binds a
socket to the source address that would be selected to communicate
with a given destination address, according to its preferences, and
then explicitly verify that the chosen address satisfies its
requirements using a validation function. Such an application would
go through the following steps:
1. The application specifies one or more IPV6_PREFER_SRC_* flags and
AI_EXTFLAGS ai_flags with getaddrinfo().
2. The application specifies the same IPV6_PREFER_SRC_* flags with
setsockopt()
3. The application calls the stack to select a source address to
communicate with the specified destination address, according to
the expressed address selection preferences. This is achieved
with a connect() call, or a bind2addrsel() call as specified
below. The connect() function must not be used when the
application uses connexion-oriented communication (e.g. TCP) and
want to ensure that no single packet (e.g. TCP SYN) is sent
before the application could verify that its requirements were
fulfilled. Instead, the application must use the newly
introduced bind2addrsel() call, which binds a socket to the
source address that would be selected to communicate with a given
destination address according to the application's preferences.
For datagram-oriented communications (e.g. UDP), the connect()
call can be used since it results in the stack selecting a source
address without sending any packet.
4. Retrieve the selected source address using the getsockname() API
call.
5. Verify with the validation function that the retrieved address is
satisfactory as specified below. If not, abort the communication
e.g., by closing the socket.
The binding of the socket to the address that would be selected to
communicate with a given destination address according to the
application preferences is accomplished via a new binding function
defined for this purpose:
Nordmark, et al. Expires December 16, 2007 [Page 22]
Internet-Draft Socket API for Source Address Selection June 2007
#include <netinet/in.h>
int bind2addrsel(int s, const struct sockaddr *dstaddr,
socklen_t dstaddrlen);
Where s is the socket which source address selection preferences have
been expressed by the application, the dstaddr is a non-NULL pointer
to a sockaddr_in6 structure initialized as follows:
o sin6_addr is a 128-bit IPv6 destination address with which the
local node wants to communicate.
o sin6_family MUST be set to AF_INET6.
o sin6_scope_id MUST be set if the address is link-local.
and dstaddrlen is the size of the sockaddr structure passed as
argument,
The bind2addrsel() call is defined to return the same values as the
bind() call, i.e. 0 if successful, -1 otherwise while the global
variable errno is set to indicate the error. The bind2addrsel() call
fails for the same reasons that the bind() call.
The verification of temporary vs. public, home vs. care-of, CGA vs.
not, are performed by a new validation function defined for this
purpose:
#include <netinet/in.h>
short inet6_is_srcaddr(struct sockaddr_in6 *srcaddr,
uint32_t flags);
Where the flags contains the specified IPV6_PREFER_SRC_* source
preference flags, and the srcaddr is a non-NULL pointer to a
sockaddr_in6 structure initialized as follows:
o sin6_addr is a 128-bit IPv6 address of the local node.
o sin6_family MUST be set to AF_INET6.
o sin6_scope_id MUST be set if the address is link-local.
inet6_is_srcaddr() is defined to return three possible values (0, 1,
-1): The function returns true (1) when the IPv6 address corresponds
to a valid address in the node and satisfies the given preference
flags. If the IPv6 address input value does not correspond to any
address in the node or if the flags are not one of the valid
Nordmark, et al. Expires December 16, 2007 [Page 23]
Internet-Draft Socket API for Source Address Selection June 2007
preference flags, it returns a failure (-1). If the input address
does not match an address which satisfies the preference flags
indicated, the function returns false (0.)
This function can handle multiple valid preference flags combination
as its second parameter, for example IPV6_PREFER_SRC_COA |
IPV6_PREFER_SRC_TMP, which means that all flags MUST be satisfied for
the result to be true. Contradictory flag values result in a false
return value.
The function will return true for IPV6_PREFER_SRC_HOME even if the
host is not implementing mobile IPv6, as well as for a mobile node
which is at home (i.e., does not have any care-of address).
Nordmark, et al. Expires December 16, 2007 [Page 24]
Internet-Draft Socket API for Source Address Selection June 2007
14. Summary of New Definitions
The following list summarizes the constants, structure, and extern
definitions discussed in this memo, sorted by header.
<netdb.h> AI_EXTFLAGS
<netdb.h> IPV6_PREFER_SRC_HOME
<netdb.h> IPV6_PREFER_SRC_COA
<netdb.h> IPV6_PREFER_SRC_TMP
<netdb.h> IPV6_PREFER_SRC_PUBLIC
<netdb.h> IPV6_PREFER_SRC_CGA
<netdb.h> IPV6_PREFER_SRC_NONCGA
<netdb.h> EAI_BADEXTFLAGS
<netdb.h> struct addrinfo{};
<netinet/in.h> IPV6_PREFER_SRC_HOME
<netinet/in.h> IPV6_PREFER_SRC_COA
<netinet/in.h> IPV6_PREFER_SRC_TMP
<netinet/in.h> IPV6_PREFER_SRC_PUBLIC
<netinet/in.h> IPV6_PREFER_SRC_CGA
<netinet/in.h> IPV6_PREFER_SRC_NONCGA
<netinet/in.h> short inet6_is_srcaddr(struct sockaddr_in6 *,
uint32_t);
<netinet/in.h> int bind2addrsel(int, const struct sockaddr *,
socklen_t);
Nordmark, et al. Expires December 16, 2007 [Page 25]
Internet-Draft Socket API for Source Address Selection June 2007
15. IANA Considerations
This document has no IANA considerations.
Nordmark, et al. Expires December 16, 2007 [Page 26]
Internet-Draft Socket API for Source Address Selection June 2007
16. Security Considerations
This document conforms to the same security implications as specified
in the Basic IPv6 socket API [RFC3493]. Allowing applications to
specify a preference for temporary addresses provides per-application
(and per-socket) ability to use the privacy benefits of the temporary
addresses. The setting of certain address preferences (e.g. not
using a CGA address, or not using a temporary address) may be
restricted to privileged processes because of security implications.
Nordmark, et al. Expires December 16, 2007 [Page 27]
Internet-Draft Socket API for Source Address Selection June 2007
17. Acknowledgments
The authors like to thank members of mobile-ip and ipv6 working
groups for useful discussion on this topic. Richard Draves and Dave
Thaler suggested that getaddrinfo also needs to be considered along
with the new socket option. Gabriel Montenegro suggested that CGAs
may also be considered in this document. Thanks to Alain Durand,
Renee Danson, Alper Yegin, Francis Dupont, Keiichi Shima, Michael
Hunter, Sebastien Roy, Robert Elz, Pekka Savola, Itojun, Jim Bound,
Jeff Boote, Steve Cipolli, Vlad Yasevich, Mika Liljeberg, Ted Hardie,
Vidya Narayanan and Lars Eggert for useful discussions and
suggestions. Thanks to Remi Denis-Courmont, Brian Haberman, Brian
Haley, Bob Gilligan, Jack McCann, Jim Bound, Jinmei Tatuya, Suresh
Krishnan, Hilarie Orman, Geoff Houston, Marcelo Bungulo and Jari
Arkko for the review of the document and suggestions for improvement.
Nordmark, et al. Expires December 16, 2007 [Page 28]
Internet-Draft Socket API for Source Address Selection June 2007
18. References
18.1. Normative references
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3484] Draves, R., "Default Address Selection for Internet
Protocol version 6 (IPv6)", RFC 3484, February 2003.
[RFC3493] Gilligan, R., Thomson, S., Bound, J., McCann, J., and W.
Stevens, "Basic Socket Interface Extensions for IPv6",
RFC 3493, February 2003.
18.2. Informative references
[FPING] "Fping - a program to ping hosts in parallel", Online web
site http://www.fping.com.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
[RFC3041] Narten, T. and R. Draves, "Privacy Extensions for
Stateless Address Autoconfiguration in IPv6", RFC 3041,
January 2001.
[RFC3542] Stevens, W., Thomas, M., Nordmark, E., and T. Jinmei,
"Advanced Sockets Application Program Interface (API) for
IPv6", RFC 3542, May 2003.
[RFC3775] Johnson, D., Perkins, C., and J. Arkko, "Mobility Support
in IPv6", RFC 3775, June 2004.
[RFC3971] Arkko, J., Kempf, J., Zill, B., and P. Nikander, "SEcure
Neighbor Discovery (SEND)", RFC 3971, March 2005.
[RFC3972] Aura, T., "Cryptographically Generated Addresses (CGA)",
RFC 3972, March 2005.
Nordmark, et al. Expires December 16, 2007 [Page 29]
Internet-Draft Socket API for Source Address Selection June 2007
Appendix A. Per Packet Address Selection Preference
This document discusses setting source address selection preferences
on a per socket basis with the new IPV6_ADDR_PREFERENCES socket
option used in setsockopt(). The document does not encourage setting
the source address selection preference on a per packet basis through
the use of ancillary data objects with sendmsg(), or setsockopt()
with unconnected datagram sockets.
Per-packet source address selection is expensive as the system will
have to determine the source address indicated by the application
preference before sending each packet, while setsockopt() address
preference on a connected socket makes the selection once and uses
that source address for all packets transmitted through that socket
end-point, as long as the socket option is set.
However, this document provides guidelines for those implementations
which like to have an option on implementing transmit-side ancillary
data object support for altering default source address selection.
Therefore, if an application chooses to use the per-packet source
address selection, then the implementation should process at the
IPPROTO_IPV6 level (cmsg_level) ancillary data object of type
(cmsg_type) IPV6_ADDR_PREFERENCES containing as data (cmsg_data[]) a
32-bits unsigned integer encoding the source address selection
preference flags (e.g. IPV6_PREFER_SRC_COA |
IPV6_PREFER_SRC_PUBLIC), in a fashion similar to the advanced IPV6
Socket API [RFC3542]. This address selection preference ancillary
data object may be present along with other ancillary data objects.
The implementation processing the ancillary data object is
responsible for selection of preferred source address as indicated in
the ancillary data object. Thus, an application can use sendmsg() to
pass an address selection preference ancillary data object to the
IPv6 layer. The following example shows usage of the ancillary data
API for setting address preferences:
Nordmark, et al. Expires December 16, 2007 [Page 30]
Internet-Draft Socket API for Source Address Selection June 2007
void *extptr;
socklen_t extlen;
struct msghdr msg;
struct cmsghdr *cmsgptr;
int cmsglen;
struct sockaddr_in6 dest;
uint32_t flags;
extlen = sizeof(flags);
cmsglen = CMSG_SPACE(extlen);
cmsgptr = malloc(cmsglen);
cmsgptr->cmsg_len = CMSG_LEN(extlen);
cmsgptr->cmsg_level = IPPROTO_IPV6;
cmsgptr->cmsg_type = IPV6_ADDR_PREFERENCES;
extptr = CMSG_DATA(cmsgptr);
flags = IPV6_PREFER_SRC_COA;
memcpy(extptr, &flags, extlen);
msg.msg_control = cmsgptr;
msg.msg_controllen = cmsglen;
/* finish filling in msg{} */
msg.msg_name = dest;
sendmsg(s, &msg, 0);
Thus when an IPV6_ADDR_PREFERENCES ancillary data object is passed to
sendmsg(), the value included in the object is used to specify
address preference for the packet being sent by sendmsg().
Nordmark, et al. Expires December 16, 2007 [Page 31]
Internet-Draft Socket API for Source Address Selection June 2007
Appendix B. Changes from previous version of draft
o Note to RFC Editor: This section is to be removed upon publication
as an RFC.
o Added an appendix discussing setting source address selection
preferences on a per packet basis, including via passing a
transmit-side ancillary data object.
o Changed getaddrinfo()usage and removed the AI_PREFER flags. Added
one extended flag field in addrinfo structure and added one
AI_flag in order to save bits.
o Removed scope address preferences as some questioned about
applicability of IPV6_PREFER_SRC and DST scope rules alterations.
o Added -1 return value for inet6_is_srcaddr() for failure
situation.
o Addressed comments by the working group and reviewers of this
draft.
o Added a definition of term for X and not-X flags.
o Changed "not-X flag" by "opposite flag", and "X and not-X flags"
by by "contradictory flags"
o updated rationale why not to deal with native transport
destination address selection rule.
Nordmark, et al. Expires December 16, 2007 [Page 32]
Internet-Draft Socket API for Source Address Selection June 2007
Appendix C. Intellectual Property Statement
This document only defines a source preference flag to choose
Cryptographically Generated Address (CGA) as source address when
applicable. CGA are obtained using public keys and hashes to prove
address ownership. Several IPR claims have been made about such
methods.
Nordmark, et al. Expires December 16, 2007 [Page 33]
Internet-Draft Socket API for Source Address Selection June 2007
Authors' Addresses
Erik Nordmark
Sun Microsystems, Inc.
4150 Network Circle, UMPK17-308
Santa Clara, CA 95054
USA
Email: Erik.Nordmark@Sun.COM
Samita Chakrabarti
Azaire Networks
3121 Jay Street, Suite 210
Santa Clara, CA 95054
USA
Email: samitac2@gmail.com
Julien Laganier
DoCoMo Euro-Labs
Landsbergerstrasse 312
D-80687 Muenchen
Germany
Email: julien.IETF@laposte.net
Nordmark, et al. Expires December 16, 2007 [Page 34]
Internet-Draft Socket API for Source Address Selection June 2007
Full Copyright Statement
Copyright (C) The IETF Trust (2007).
This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.
This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Intellectual Property
The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.
Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.
Acknowledgment
Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).
Nordmark, et al. Expires December 16, 2007 [Page 35]