Skip to main content

Guidelines for Implementing Digital Video Broadcasting - IPTV (DVB-IPTV) Application-Layer Hybrid Forward Error Correction (FEC) Protection
RFC 6683

Document Type RFC - Informational (August 2012)
Authors Ali C. Begen , Thomas Stockhammer
Last updated 2015-10-14
RFC stream Internet Engineering Task Force (IETF)
Formats
Additional resources Mailing list discussion
IESG Responsible AD Martin Stiemerling
Send notices to (None)
RFC 6683
Internet Engineering Task Force (IETF)                          A. Begen
Request for Comments: 6683                                         Cisco
Category: Informational                                   T. Stockhammer
ISSN: 2070-1721                                           Nomor Research
                                                             August 2012

Guidelines for Implementing Digital Video Broadcasting - IPTV (DVB-IPTV)
   Application-Layer Hybrid Forward Error Correction (FEC) Protection

Abstract

   Annex E of the Digital Video Broadcasting - IPTV (DVB-IPTV) technical
   specification defines an optional Application-Layer Forward Error
   Correction (AL-FEC) protocol to protect the streaming media
   transported using RTP.  The DVB-IPTV AL-FEC protocol uses two layers
   for FEC protection.  The first (base) layer is based on the 1-D
   interleaved parity code.  The second (enhancement) layer is based on
   the Raptor code.  By offering a layered approach, the DVB-IPTV AL-FEC
   protocol offers good protection against both bursty and random packet
   losses at a cost of decent complexity.  This document describes how
   one can implement the DVB-IPTV AL-FEC protocol by using the 1-D
   interleaved parity code and Raptor code that have already been
   specified in separate documents.

Status of This Memo

   This document is not an Internet Standards Track specification; it is
   published for informational purposes.

   This document is a product of the Internet Engineering Task Force
   (IETF).  It represents the consensus of the IETF community.  It has
   received public review and has been approved for publication by the
   Internet Engineering Steering Group (IESG).  Not all documents
   approved by the IESG are a candidate for any level of Internet
   Standard; see Section 2 of RFC 5741.

   Information about the current status of this document, any errata,
   and how to provide feedback on it may be obtained at
   http://www.rfc-editor.org/info/rfc6683.

Begen & Stockhammer           Informational                     [Page 1]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

Copyright Notice

   Copyright (c) 2012 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  2
   2.  DVB-IPTV AL-FEC Specification  . . . . . . . . . . . . . . . .  5
     2.1.  Base-Layer FEC . . . . . . . . . . . . . . . . . . . . . .  5
     2.2.  Enhancement-Layer FEC  . . . . . . . . . . . . . . . . . .  7
     2.3.  Hybrid Decoding Procedures . . . . . . . . . . . . . . . .  7
   3.  Session Description Protocol (SDP) Signaling . . . . . . . . .  8
   4.  Security Considerations  . . . . . . . . . . . . . . . . . . .  9
   5.  Acknowledgments  . . . . . . . . . . . . . . . . . . . . . . .  9
   6.  References . . . . . . . . . . . . . . . . . . . . . . . . . . 10
     6.1.  Normative References . . . . . . . . . . . . . . . . . . . 10
     6.2.  Informative References . . . . . . . . . . . . . . . . . . 10

1.  Introduction

   In 2007, the IP Infrastructure (IPI) Technical Module (TM) of the
   Digital Video Broadcasting (DVB) consortium published a technical
   specification [ETSI-TS-102-034v1.3.1] through the European
   Telecommunications Standards Institute (ETSI).
   [ETSI-TS-102-034v1.3.1] covers several areas related to the
   transmission of MPEG2 transport stream-based services over IP
   networks.

   Annex E of [ETSI-TS-102-034v1.3.1] defines an optional protocol for
   Application-Layer Forward Error Correction (AL-FEC) to protect the
   streaming media for DVB-IP services transported using RTP [RFC3550].
   In 2009, DVB updated the specification in a new revision that is
   available as [ETSI-TS-102-034v1.4.1].  Among others, some updates and
   modifications to the AL-FEC protocol have been made.  This document
   describes how one can implement the DVB-IPTV AL-FEC protocol by using
   the 1-D interleaved parity code [RFC6015] and Raptor code
   specifications [RFC6681] [RFC6682].

Begen & Stockhammer           Informational                     [Page 2]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

   The DVB-IPTV AL-FEC protocol uses two layers for protection:  a base
   layer that is produced by the 1-D interleaved parity code (also
   simply referred to as "parity code" in the remainder of this
   document), and an enhancement layer that is produced by the Raptor
   code.  Whenever a receiver supports the DVB-IPTV AL-FEC protocol, the
   decoding support for the base-layer FEC is mandatory while the
   decoding support for the enhancement-layer FEC is optional.  Both the
   interleaved parity code and the Raptor code are systematic FEC codes,
   meaning that source packets are not modified in any way during the
   FEC encoding process.

   The DVB-IPTV AL-FEC protocol considers protection of single-sequence
   source RTP flows only.  In the AL-FEC protocol, the source stream can
   only be an MPEG-2 transport stream.  The FEC data at each layer are
   generated based on some configuration information, which also
   determines the exact associations and relationships between the
   source and repair packets.  This document shows how this
   configuration may be communicated out-of-band in the Session
   Description Protocol (SDP) [RFC4566].

   In DVB-IPTV AL-FEC, the source packets are carried in the source RTP
   stream and the generated FEC repair packets at each layer are carried
   in separate streams.  At the receiver side, if all of the source
   packets are successfully received, there is no need for FEC recovery
   and the repair packets may be discarded.  However, if there are
   missing source packets, the repair packets can be used to recover the
   missing information.

   The block diagram of the encoder side for the systematic DVB-IPTV
   AL-FEC protection is described in Figure 1.  Here, the source packets
   are fed into the parity encoder to produce the parity repair packets.
   The source packets may also be fed to the Raptor encoder to produce
   the Raptor repair packets.  Source packets as well as the repair
   packets are then sent to the receiver(s) over an IP network.

Begen & Stockhammer           Informational                     [Page 3]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

                              +--------------+
   +--+  +--+  +--+  +--+ --> |  Systematic  | -> +--+  +--+  +--+  +--+
   +--+  +--+  +--+  +--+     |FEC Protection|    +--+  +--+  +--+  +--+
                              +--------------+
                              |    Parity    | -> +==+  +==+  +==+
                              |    Encoder   |    +==+  +==+  +==+
                              +--------------+
                              |    Raptor    | -> +~~+  +~~+
                              |    Encoder   |    +~~+  +~~+
                              +--------------+

   Source Packet: +--+
                  +--+

   Base-layer Repair Packet: +==+
                             +==+

   Enhancement-layer Repair Packet: +~~+
                                    +~~+

          Figure 1: Block Diagram for the DVB-IPTV AL-FEC Encoder

   The block diagram of the decoder side for the systematic DVB-IPTV
   AL-FEC protection is described in Figure 2.  This is a minimum
   performance decoder since the receiver only supports decoding the
   base-layer repair packets.  If there is a loss among the source
   packets, the parity decoder attempts to recover the missing source
   packets by using the base-layer repair packets.

                              +--------------+
   +--+   X     X    +--+ --> |  Systematic  | -> +--+  +--+  +--+  +--+
   +--+              +--+     |FEC Protection|    +--+  +--+  +--+  +--+
                              +--------------+
         +==+  +==+  +==+ --> |    Parity    |
         +==+  +==+  +==+     |    Decoder   |
                              +--------------+

   Lost Packet: X

    Figure 2: Block Diagram for the DVB-IPTV AL-FEC Minimum Performance
                                  Decoder

   On the other hand, if the receiver supports decoding both the base-
   layer and enhancement-layer repair packets, a combined (hybrid)
   decoding approach is employed to improve the recovery rate of the
   lost packets.  In this case, the decoder is called an enhanced
   decoder.  Section 2.3 outlines the procedures for hybrid decoding.

Begen & Stockhammer           Informational                     [Page 4]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

                              +--------------+
   +--+   X     X     X   --> |  Systematic  | -> +--+  +--+  +--+  +--+
   +--+                       |FEC Protection|    +--+  +--+  +--+  +--+
                              +--------------+
         +==+  +==+  +==+ --> |    Parity    |
         +==+  +==+  +==+     |    Decoder   |
                              +--------------+
               +~~+  +~~+ --> |    Raptor    |
               +~~+  +~~+     |    Decoder   |
                              +--------------+

   Lost Packet: X

     Figure 3: Block Diagram for the DVB-IPTV AL-FEC Enhanced Decoder

2.  DVB-IPTV AL-FEC Specification

   The DVB-IPTV AL-FEC protocol comprises two layers of FEC protection:
   1-D interleaved parity FEC for the base layer and Raptor FEC for the
   enhancement layer.  The performance of these FEC codes has been
   examined in detail in [DVB-A115].

2.1.  Base-Layer FEC

   The 1-D interleaved parity FEC uses the exclusive OR (XOR) operation
   to generate the repair symbols.  In a group of D x L source packets,
   the XOR operation is applied to each group of D source packets whose
   sequence numbers are L apart from each other to generate a total of L
   repair packets.  Due to interleaving, this FEC is effective against
   bursty packet losses up to burst sizes of length L.

   The DVB-IPTV AL-FEC protocol requires that the D x L block of the
   source packets protected by the 1-D interleaved FEC code be wholly
   contained within a single source block of the Raptor code, if both
   FEC layers are used.

   Originally, the DVB-IPTV AL-FEC protocol had adopted the 1-D
   interleaved FEC payload format from [SMPTE2022-1] in
   [ETSI-TS-102-034v1.3.1].  However, some incompatibilities with RTP
   [RFC3550] have been discovered in this specification.  These issues
   have all been addressed in [RFC6015] (for details, refer to Section 1
   of [RFC6015]).  Some of the changes required by [RFC6015] are,
   however, not backward compatible with the existing implementations
   that were based on [SMPTE2022-1].

   In a recent liaison statement from the IETF AVT WG to DVB TM-IPI, it
   has been recommended that DVB TM-IPI define a new RTP profile for the

Begen & Stockhammer           Informational                     [Page 5]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

   AL-FEC protocol since in the new profile, several of the issues could
   easily be addressed without jeopardizing the compliance to RTP
   [RFC3550].

   At the writing of this document, it was not clear whether or not a
   new RTP profile would be defined for the AL-FEC protocol.  DVB TM-IPI
   attempted to address some of the issues in the updated specification
   [ETSI-TS-102-034v1.4.1]; however, there are still outstanding issues.

   The following is a list of the exceptions that need to be considered
   by an implementation adopting [RFC6015] to be compliant with the DVB-
   IPTV AL-FEC protocol as specified in [ETSI-TS-102-034v1.4.1].

   o  SSRC (synchronization source)
      The DVB-IPTV AL-FEC protocol requires that the SSRC fields of the
      FEC packets be set to zero.

      This requirement conflicts with RTP [RFC3550].  Unless signaled
      otherwise, RTP uses random SSRC values with collision detection.
      An explicit SSRC signaling mechanism is currently defined in
      [RFC5576] and can be used for this purpose.

   o  CSRC (contributing source)
      The DVB-IPTV AL-FEC protocol does not support the protection of
      the CSRC entries in the source packets.  Thus, in an
      implementation compliant to DVB-IPTV AL-FEC protocol, the source
      stream must not have any CSRC entries in its packets, and
      subsequently the CC fields of the source RTP packets will be zero.

      Note that if there are no RTP mixers used in a system running the
      DVB-IPTV AL-FEC protocol, the CC field of the source RTP packets
      will be zero and this is no longer an issue.  Thus, if defined,
      the new RTP profile for the DVB-IPTV AL-FEC protocol should forbid
      the use of any RTP mixers.

   o  Timestamp
      In the DVB-IPTV AL-FEC protocol, the timestamp fields of the FEC
      packets are ignored by the receivers.

   o  Payload Type
      The DVB-IPTV AL-FEC protocol sets the PT fields of the FEC packets
      to 96.

      A static payload type assignment for the base-layer FEC packets is
      outside the scope of [RFC6015].  If defined, the new RTP profile
      for the DVB-IPTV AL-FEC protocol may assign 96 as the payload type
      for the base-layer FEC packets.

Begen & Stockhammer           Informational                     [Page 6]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

   In implementations that are based on [RFC6015] and are willing to be
   compliant with the DVB-IPTV AL-FEC protocol as specified in
   [ETSI-TS-102-034v1.3.1], all these exceptions must be considered as
   well; however, in this case, the sender does not have to select a
   random initial sequence number for the FEC stream as suggested by
   [RFC3550].

   Note that neither [ETSI-TS-102-034v1.3.1] nor [ETSI-TS-102-034v1.4.1]
   implements the 1-D interleaved parity code as specified in [RFC6015].
   Thus, the payload format registered in [RFC6015] must not be used by
   the implementations that are compliant with the
   [ETSI-TS-102-034v1.3.1] or [ETSI-TS-102-034v1.4.1] specification.

2.2.  Enhancement-Layer FEC

   The Raptor code is a fountain code where as many encoding symbols as
   needed can be generated by the encoder on-the-fly from source data.
   Due to the fountain property of the Raptor code, multiple enhancement
   layers may also be specified, if needed.

   The details of the Raptor code are provided in [RFC6681].  The FEC
   scheme for the enhancement layer SHALL be the Raptor FEC scheme for a
   Single Sequenced Flow with FEC encoding ID 5.  The RTP payload format
   for Raptor FEC is specified in [RFC6682].

   It is important to note that the DVB-IPTV AL-FEC protocol in the
   latest specification [ETSI-TS-102-034v1.4.1] allows both UDP-only and
   RTP-over-UDP encapsulations for the enhancement-layer FEC stream.
   The initial specification [ETSI-TS-102-034v1.3.1] exclusively permits
   UDP-only encapsulation for the enhancement-layer FEC stream.

   When SDP is used for signaling, the transport protocol identifier
   indicates whether an RTP-over-UDP or UDP-only encapsulation is used.
   In case of any other signaling framework, the differentiation of the
   protocol for the enhancement-layer stream is achieved either
   explicitly through a protocol identifier or implicitly by the version
   number of the DVB IPTV Handbook.  If none of the above signaling is
   provided, the receiver shall concur from the packet size of the
   repair packets if RTP-over-UDP or UDP-only encapsulation is used.

2.3.  Hybrid Decoding Procedures

   The receivers that support receiving and decoding both the base- and
   enhancement-layer FEC perform hybrid decoding to improve the repair
   performance.  The following steps may be followed to perform hybrid
   decoding:

Begen & Stockhammer           Informational                     [Page 7]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

   1.  Base-layer (Parity) Decoding:  In this step, the repair packets
       that are encoded by the parity encoder are processed as usual to
       repair as many missing source packets as possible.

   2.  Enhancement-layer (Raptor) Decoding:  If there are still missing
       source packets after the first step, the repair packets that are
       Raptor encoded are processed with the source packets already
       received and the source packets that are recovered in the first
       step.

   3.  Hybrid Decoding:  If there are still missing source packets after
       the second step, the unprocessed base-layer (parity) repair
       packets are converted to a form in which they can be added to the
       Raptor decoding process.  With this additional information,
       Raptor decoding may potentially recover any remaining missing
       source packet.

   The procedure that should be followed to benefit from the base-layer
   repair packets in the Raptor decoding process is explained in detail
   in Annex E.5.2 of [ETSI-TS-102-034v1.4.1].

3.  Session Description Protocol (SDP) Signaling

   This section provides an SDP [RFC4566] example for
   [ETSI-TS-102-034v1.4.1].  The example uses the FEC grouping semantics
   [RFC5956].

   In the example, we have one source video stream (mid:S1), one FEC
   repair stream (mid:R1) that is produced by the 1-D interleaved parity
   FEC code, as well as another FEC repair stream (mid:R2) that is
   produced by the Raptor FEC code.  We form one FEC group with the
   "a=group:FEC-FR S1 R1 R2" line.  The source and repair streams are
   sent to the same port on different multicast groups.  The source,
   base-layer FEC, and enhancement-layer FEC streams are all
   encapsulated in RTP.

   Due to the exceptions described in Section 2.1, a
   [ETSI-TS-102-034v1.4.1]-compliant implementation must not use the RTP
   payload format defined in [RFC6015].  Instead, it may use the payload
   format that has been registered by DVB TM-IPI for
   [ETSI-TS-102-034v1.3.1].

Begen & Stockhammer           Informational                     [Page 8]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

        v=0
        o=ali 1122334455 1122334466 IN IP4 fec.example.com
        s=DVB-IPTV AL-FEC Example
        t=0 0
        a=group:FEC-FR S1 R1 R2
        m=video 30000 RTP/AVP 100
        c=IN IP4 233.252.0.1/127
        a=rtpmap:100 MP2T/90000
        a=mid:S1
        m=application 30000 RTP/AVP 96
        c=IN IP4 233.252.0.2/127
        a=rtpmap:96 vnd.dvb.iptv.alfec-base/90000
        a=mid:R1
        m=application 30000 RTP/AVP 111
        c=IN IP4 233.252.0.3/127
        a=rtpmap:111 vnd.dvb.iptv.alfec-enhancement/90000
        a=mid:R2

   Note that in the example above, the payload type has been chosen as
   96 for the base-layer FEC stream and there is no "a=fmtp:" line to
   specify the format parameters.  Due to the lack of the format
   parameters for "vnd.dvb.iptv.alfec-base", it is not possible to learn
   the FEC parameters from the SDP description.

4.  Security Considerations

   This specification adds no new security considerations to the DVB-
   IPTV AL-FEC protocol.

5.  Acknowledgments

   This document is based on [ETSI-TS-102-034v1.3.1] and
   [ETSI-TS-102-034v1.4.1].  Thus, the authors would like to thank the
   editors of [ETSI-TS-102-034v1.3.1] and [ETSI-TS-102-034v1.4.1].  The
   authors also would like to thank those who reviewed earlier versions
   of this document.

Begen & Stockhammer           Informational                     [Page 9]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

6.  References

6.1.  Normative References

   [ETSI-TS-102-034v1.3.1]
              ETSI TS 102 034 V1.3.1, "Transport of MPEG 2 TS Based DVB
              Services over IP Based Networks", October 2007.

   [ETSI-TS-102-034v1.4.1]
              ETSI TS 102 034 V1.4.1, "Transport of MPEG 2 TS Based DVB
              Services over IP Based Networks", August 2009.

   [RFC6015]  Begen, A., "RTP Payload Format for 1-D Interleaved Parity
              Forward Error Correction (FEC)", RFC 6015, October 2010.

   [RFC6681]  Watson, M., Stockhammer, T., and M. Luby, "Raptor FEC
              Schemes for FECFRAME", RFC RFC6681, August 2012.

   [RFC6682]  Watson, M., Stockhammer, T., and M. Luby, "RTP Payload
              Format for Raptor Forward Error Correction (FEC)",
              RFC 6682, August 2012.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, July 2003.

   [RFC5576]  Lennox, J., Ott, J., and T. Schierl, "Source-Specific
              Media Attributes in the Session Description Protocol
              (SDP)", RFC 5576, June 2009.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, July 2006.

   [RFC5956]  Begen, A., "Forward Error Correction Grouping Semantics in
              the Session Description Protocol", RFC 5956,
              September 2010.

6.2.  Informative References

   [DVB-A115]
              "DVB Application Layer FEC Evaluations (DVB Document
              A115)", May 2007, <http://www.dvb.org/technology/
              standards/a115.tm3783.AL-FEC_Evaluation.pdf>.

   [SMPTE2022-1]
              SMPTE 2022-1-2007, "Forward Error Correction for Real-Time
              Video/Audio Transport over IP Networks", 2007.

Begen & Stockhammer           Informational                    [Page 10]
RFC 6683           Guidelines for DVB AL-FEC Protocol        August 2012

Authors' Addresses

   Ali Begen
   Cisco
   181 Bay Street
   Toronto, ON  M5J 2T3
   Canada

   EMail:  abegen@cisco.com

   Thomas Stockhammer
   Nomor Research
   Brecherspitzstrasse 8
   Munich,   81541
   Germany

   EMail:  stockhammer@nomor.de

Begen & Stockhammer           Informational                    [Page 11]