Skip to main content

Inter-Domain MPLS and GMPLS Traffic Engineering -- Resource Reservation Protocol-Traffic Engineering (RSVP-TE) Extensions
RFC 5151

Document Type RFC - Proposed Standard (February 2008) Errata
Authors Adrian Farrel , JP Vasseur , Arthi Ayyangar
Last updated 2020-01-21
RFC stream Internet Engineering Task Force (IETF)
Formats
Additional resources Mailing list discussion
IESG Responsible AD Ross Callon
Send notices to (None)
RFC 5151
Network Working Group                                     A. Farrel, Ed.
Request for Comments: 5151                            Old Dog Consulting
Updates: 3209, 3473                                          A. Ayyangar
Category: Standards Track                               Juniper Networks
                                                             JP. Vasseur
                                                     Cisco Systems, Inc.
                                                           February 2008

          Inter-Domain MPLS and GMPLS Traffic Engineering --
 Resource Reservation Protocol-Traffic Engineering (RSVP-TE) Extensions

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Abstract

   This document describes procedures and protocol extensions for the
   use of Resource Reservation Protocol-Traffic Engineering (RSVP-TE)
   signaling in Multiprotocol Label Switching-Traffic Engineering
   (MPLS-TE) packet networks and Generalized MPLS (GMPLS) packet and
   non-packet networks to support the establishment and maintenance of
   Label Switched Paths that cross domain boundaries.

   For the purpose of this document, a domain is considered to be any
   collection of network elements within a common realm of address space
   or path computation responsibility.  Examples of such domains include
   Autonomous Systems, Interior Gateway Protocol (IGP) routing areas,
   and GMPLS overlay networks.

Farrel, et al.              Standards Track                     [Page 1]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

Table of Contents

   1. Introduction ....................................................3
      1.1. Conventions Used in This Document ..........................3
      1.2. Terminology ................................................4
   2. Signaling Overview ..............................................4
      2.1. Signaling Options ..........................................5
   3. Procedures on the Domain Border Node ............................6
      3.1. Rules on ERO Processing ....................................8
      3.2. LSP Setup Failure and Crankback ...........................10
      3.3. RRO Processing across Domains .............................11
      3.4. Notify Message Processing .................................11
   4. RSVP-TE Signaling Extensions ...................................12
      4.1. Control of Downstream Choice of Signaling Method ..........12
   5. Protection and Recovery of Inter-Domain TE LSPs ................13
      5.1. Fast Recovery Support Using MPLS-TE Fast Reroute (FRR) ....14
           5.1.1. Failure within a Domain (Link or Node Failure) .....14
           5.1.2. Failure of Link at Domain Border ...................14
           5.1.3. Failure of a Border Node ...........................15
      5.2. Protection and Recovery of GMPLS LSPs .....................15
   6. Reoptimization of Inter-Domain TE LSPs .........................16
   7. Backward Compatibility .........................................17
   8. Security Considerations ........................................18
   9. IANA Considerations ............................................20
      9.1. Attribute Flags for LSP_Attributes Object .................20
      9.2. New Error Codes ...........................................20
   10. Acknowledgments ...............................................21
   11. References ....................................................21
       11.1. Normative References ....................................21
       11.2. Informative References ..................................22

Farrel, et al.              Standards Track                     [Page 2]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

1.  Introduction

   The requirements for inter-area and inter-AS (Autonomous System)
   Multiprotocol Label Switching (MPLS) Traffic Engineering (TE) are
   stated in [RFC4105] and [RFC4216], respectively.  Many of these
   requirements also apply to Generalized MPLS (GMPLS) networks.  The
   framework for inter-domain MPLS-TE is provided in [RFC4726].

   This document presents procedures and extensions to Resource
   Reservation Protocol-Traffic Engineering (RSVP-TE) signaling for the
   setup and maintenance of traffic engineered Label Switched Paths (TE
   LSPs) that span multiple domains in MPLS-TE or GMPLS networks.  The
   signaling procedures described in this document are applicable to
   MPLS-TE packet LSPs established using RSVP-TE ([RFC3209]) and all
   LSPs (packet and non-packet) that use RSVP-TE GMPLS extensions as
   described in [RFC3473].

   Three different signaling methods for inter-domain RSVP-TE signaling
   are identified in [RFC4726].  Contiguous LSPs are achieved using the
   procedures of [RFC3209] and [RFC3473] to create a single end-to-end
   LSP that spans all domains.  Nested LSPs are established using the
   techniques described in [RFC4206] to carry the end-to-end LSP in a
   separate tunnel across each domain.  Stitched LSPs are established
   using the procedures of [RFC5150] to construct an end-to-end LSP from
   the concatenation of separate LSPs each spanning a domain.

   This document defines the RSVP-TE protocol extensions necessary to
   control and select which of the three signaling mechanisms is used
   for any one end-to-end inter-domain TE LSP.

   For the purpose of this document, a domain is considered to be any
   collection of network elements within a common realm of address space
   or path computation responsibility.  Examples of such domains include
   Autonomous Systems, IGP areas, and GMPLS overlay networks
   ([RFC4208]).

1.1.  Conventions Used in This Document

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

Farrel, et al.              Standards Track                     [Page 3]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

1.2.  Terminology

   AS: Autonomous System.

   ASBR: Autonomous System Border Router.  A router used to connect
   together ASs of a different or the same Service Provider via one or
   more inter-AS links.

   Bypass Tunnel: An LSP that is used to protect a set of LSPs passing
   over a common facility.

   ERO: Explicit Route Object.

   FA: Forwarding Adjacency.

   LSR: Label Switching Router.

   MP: Merge Point.  The node where bypass tunnels meet the protected
   LSP.

   NHOP bypass tunnel: Next-Hop Bypass Tunnel.  A backup tunnel, which
   bypasses a single link of the protected LSP.

   NNHOP bypass tunnel: Next-Next-Hop Bypass Tunnel.  A backup tunnel,
   which bypasses a single node of the protected LSP.

   PLR: Point of Local Repair.  The ingress of a bypass tunnel.

   RRO: Record Route Object.

   TE link: Traffic Engineering link.

2.  Signaling Overview

   The RSVP-TE signaling of a TE LSP within a single domain is described
   in [RFC3209] and [RFC3473].  Inter-domain TE LSPs can be supported by
   one of three options as described in [RFC4726] and set out in the
   next section:

   - contiguous LSPs
   - nested LSPs
   - stitched LSPs.

   In fact, as pointed out in [RFC4726], any combination of these three
   options may be used in the course of an end-to-end inter-domain LSP.
   That is, the options should be considered as per-domain transit
   options so that an end-to-end inter-domain LSP that starts in domain
   A, transits domains B, C, and D, and ends in domain E might use an

Farrel, et al.              Standards Track                     [Page 4]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   LSP that runs contiguously from the ingress in domain A, through
   domain B to the border with domain C.  Domain C might be transited
   using the nested LSP option to reach the border with domain D, and
   domain D might be transited using the stitched LSP option to reach
   the border with domain E, from where a normal LSP runs to the egress.

   This document describes the RSVP-TE signaling extensions required to
   select and control which of the three signaling mechanisms is used.

   The specific protocol extensions required to signal each LSP type are
   described in other documents and are out of scope for this document.
   Similarly, the routing extensions and path computation techniques
   necessary for the establishment of inter-domain LSPs are out of
   scope.  An implementation of a transit LSR is unaware of the options
   for inter-domain TE LSPs since it sees only TE LSPs.  An
   implementation of a domain border LSR has to decide what mechanisms
   of inter-domain TE LSP support to include, but must in any case
   support contiguous inter-domain TE LSPs since this is the default
   mode of operation for RSVP-TE.  Failure to support either or both of
   nested LSPs or stitched LSPs, restricts the operators options, but
   does not prevent the establishment of inter-domain TE LSPs.

2.1.  Signaling Options

   There are three ways in which an RSVP-TE LSP could be signaled across
   multiple domains:

   Contiguous
      A contiguous TE LSP is a single TE LSP that is set up across
      multiple domains using RSVP-TE signaling procedures described in
      [RFC3209] and [RFC3473].  No additional TE LSPs are required to
      create a contiguous TE LSP, and the same RSVP-TE information for
      the TE LSP is maintained along the entire LSP path.  In
      particular, the TE LSP has the same RSVP-TE session and LSP ID at
      every LSR along its path.

   Nested
      One or more TE LSPs may be nested within another TE LSP as
      described in [RFC4206].  This technique can be used to nest one or
      more inter-domain TE LSPs into an intra-domain hierarchical LSP
      (H-LSP).  The label stacking construct is used to achieve nesting
      in packet networks.  In the rest of this document, the term H-LSP
      is used to refer to an LSP that allows other LSPs to be nested
      within it.  An H-LSP may be advertised as a TE link within the
      same instance of the routing protocol as was used to advertise the
      TE links from which it was created, in which case it is a
      Forwarding Adjacency (FA) [RFC4206].

Farrel, et al.              Standards Track                     [Page 5]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   Stitched
      The concept of LSP stitching as well as the required signaling
      procedures are described in [RFC5150].  This technique can be used
      to stitch together shorter LSPs (LSP segments) to create a single,
      longer LSP.  The LSP segments of an inter-domain LSP may be
      intra-domain LSPs or inter-domain LSPs.

      The process of stitching in the data plane results in a single,
      end-to-end contiguous LSP.  But in the control plane, each segment
      is signaled as a separate LSP (with distinct RSVP sessions) and
      the end-to-end LSP is signaled as yet another LSP with its own
      RSVP session.  Thus, the control plane operation for LSP stitching
      is very similar to that for nesting.

   An end-to-end inter-domain TE LSP may be achieved using one or more
   of the signaling techniques described.  The choice is a matter of
   policy for the node requesting LSP setup (the ingress) and policy for
   each successive domain border node.  On receipt of an LSP setup
   request (RSVP-TE Path message) for an inter-domain TE LSP, the
   decision of whether to signal the LSP contiguously or whether to nest
   or stitch it to another TE LSP depends on the parameters signaled
   from the ingress node and on the configuration of the local node.

   The stitching segment LSP or H-LSP used to cross a domain may be
   pre-established or signaled dynamically based on the demand caused by
   the arrival of the inter-domain TE LSP setup request.

3.  Procedures on the Domain Border Node

   Whether an inter-domain TE LSP is contiguous, nested, or stitched is
   limited by the signaling methods supported by or configured on the
   intermediate nodes.  It is usually the domain border nodes where this
   restriction applies since other transit nodes are oblivious to the
   mechanism in use.  The ingress of the LSP may further restrict the
   choice by setting parameters in the Path message when it is signaled.

   When a domain border node receives the RSVP Path message for an
   inter-domain TE LSP setup, it MUST carry out the following procedures
   before it can forward the Path message to the next node along the
   path:

      1.  Apply policies for the domain and the domain border node.
          These policies may restrict the establishment of inter-domain
          TE LSPs.  In case of a policy failure, the node SHOULD fail
          the setup and send a PathErr message with error code "Policy
          control failure"/ "Inter-domain policy failure".

Farrel, et al.              Standards Track                     [Page 6]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

      2.  Determine the signaling method to be used to cross the domain.
          If the ingress node of the inter-domain TE LSP has specified
          restrictions on the methods to be used, these MUST be adhered
          to.  Within the freedom allowed by the ingress node, the
          domain border node MAY choose any method according to local
          configuration and policies.  If no resultant signaling method
          is available or allowed, the domain border node MUST send a
          PathErr message with an error code as described in Section
          4.1.

          Thus, for example, an ingress may request a contiguous LSP
          because it wishes to exert maximal control over the LSP's path
          and to control when reoptimization takes place.  But the
          operator of a transit domain may decide (for example) that
          only LSP stitching is allowed for exactly the reason that it
          gives the operator the chance to reoptimize their own domain
          under their own control.  In this case, the policy applied at
          the entry to the transit domain will result in the return of a
          PathErr message and the ingress has a choice to:

          - find another path avoiding the transit domain,
          - relax his requirements, or
          - fail to provide the service.

      3.  Carry out ERO procedures as described in Section 3 in addition
          to the procedures in [RFC3209] and [RFC3473].

      4.  Perform any path computations as required to determine the
          path across the domain and potentially to select the exit
          point from the domain.

          The path computation procedure is outside the scope of this
          document.  A path computation option is specified in
          [RFC5152], and another option is to use a Path Computation
          Element (PCE) [RFC4655].

         4a.  In the case of nesting or stitching, either find an
              existing intra-domain TE LSP to carry the inter-domain TE
              LSP or signal a new one, depending on local policy.

          In the event of a path computation failure, a PathErr message
          SHOULD be sent with error code "Routing Problem" using an
          error value selected according to the reason for computation
          failure.  A domain border node MAY opt to silently discard the
          Path message in this case as described in Section 8.

Farrel, et al.              Standards Track                     [Page 7]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   In the event of the receipt of a PathErr message reporting signaling
   failure from within the domain or reported from a downstream domain,
   the domain border node MAY apply crankback procedures as described in
   Section 3.2.  If crankback is not applied, or is exhausted, the
   border node MUST continue with PathErr processing as described in
   [RFC3209] and [RFC3473].

   In the event of successful processing of a Path or Resv message, the
   domain border node MUST carry out RRO procedures as described in
   Section 3.3.

3.1.  Rules on ERO Processing

   The ERO that a domain border node receives in the Path message was
   supplied by the ingress node of the TE LSP and may have been updated
   by other nodes (for example, other domain border nodes) as the Path
   message was propagated.  The content of the ERO depends on several
   factors including:

   - the path computation techniques used,
   - the degree of TE visibility available to the nodes performing path
     computation, and
   - the policy at the nodes creating/modifying the ERO.

   In general, H-LSPs and LSP segments are used between domain border
   nodes, but there is no restriction on the use of such LSPs to span
   multiple hops entirely within a domain.  Therefore, the discussion
   that follows may be equally applied to any node within a domain
   although the term "domain border node" continues to be used for
   clarity.

   When a Path message reaches the domain border node, the following
   rules apply for ERO processing and for further signaling.

      1.  If there are any policies related to ERO processing for the
          LSP, they MUST be applied and corresponding actions MUST be
          taken.  For example, there might be a policy to reject EROs
          that identify nodes within the domain.  In case of
          inter-domain LSP setup failures due to policy failures related
          to ERO processing, the node SHOULD issue a PathErr with error
          code "Policy control failure"/"Inter-domain explicit route
          rejected", but MAY be configured to silently discard the Path
          message or to return a different error code for security
          reasons.

Farrel, et al.              Standards Track                     [Page 8]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

      2.  Section 8.2 of [RFC4206] describes how a node at the edge of a
          region processes the ERO in the incoming Path message and uses
          this ERO, to either find an existing H-LSP or signal a new
          H-LSP using the ERO hops.  This process includes adjusting the
          ERO before sending the Path message to the next hop.  These
          procedures MUST be followed for nesting or stitching of
          inter-domain TE LSPs.

      3.  If an ERO subobject identifies a TE link formed by the
          advertisement of an H-LSP or LSP segment (whether numbered or
          unnumbered), contiguous signaling MUST NOT be used.  The node
          MUST use either nesting or stitching according to the
          capabilities of the LSP that forms the TE link, the parameters
          signaled in the Path message, and local policy.  If there is a
          conflict between the capabilities of the LSP that forms the TE
          link indicated in the ERO and the parameters on the Path
          message, the domain border node SHOULD send a PathErr with
          error code "Routing Problem"/"ERO conflicts with inter-domain
          signaling method", but MAY be configured to silently discard
          the Path message or to return a different error code for
          security reasons.

      4.  An ERO in a Path message received by a domain border node may
          have a loose hop as the next hop.  This may be an IP address
          or an AS number.  In such cases, the ERO MUST be expanded to
          determine the path to the next hop using some form of path
          computation that may, itself, generate loose hops.

      5.  In the absence of any ERO subobjects beyond the local domain
          border node, the LSP egress (the destination encoded in the
          RSVP Session object) MUST be considered as the next loose hop
          and rule 4 applied.

      6.  In the event of any other failures processing the ERO, a
          PathErr message SHOULD be sent as described in [RFC3209] or
          [RFC3473], but a domain border router MAY be configured to
          silently discard the Path message or to return a different
          error code for security reasons.

Farrel, et al.              Standards Track                     [Page 9]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

3.2.  LSP Setup Failure and Crankback

   When an error occurs during LSP setup, a PathErr message is sent back
   towards the LSP ingress node to report the problem.  If the LSP
   traverses multiple domains, this PathErr will be seen successively by
   each domain border node.

   Domain border nodes MAY apply local policies to restrict the
   propagation of information about the contents of the domain.  For
   example, a domain border node MAY replace the information in a
   PathErr message that indicates a specific failure at a specific node
   with information that reports a more general error with the entire
   domain.  These procedures are similar to those described for the
   borders of overlay networks in [RFC4208].

   However:

   - A domain border node MUST NOT suppress the propagation of a PathErr
     message except to attempt rerouting as described below.

   - Nodes other than domain border nodes SHOULD NOT modify the contents
     of a PathErr message.

   - Domain border nodes SHOULD NOT modify the contents of a PathErr
     message unless domain confidentiality is a specific requirement.

   Domain border nodes provide an opportunity for crankback rerouting
   [RFC4920].  On receipt of a PathErr message generated because of an
   LSP setup failure, a domain border node MAY hold the PathErr and make
   further attempts to establish the LSP if allowed by local policy and
   by the parameters signaled on the Path message for the LSP.  Such
   attempts might involve the computation of alternate routes through
   the domain, or the selection of different downstream domains.  If a
   subsequent attempt is successful, the domain border router MUST
   discard the held PathErr message, but if all subsequent attempts are
   unsuccessful, the domain border router MUST send the PathErr upstream
   toward the ingress node.  In this latter case, the domain border
   router MAY change the information in the PathErr message to provide
   further crankback details and information aggregation as described in
   [RFC4920].

   Crankback rerouting MAY also be used to handle the failure of LSPs
   after they have been established [RFC4920].

Farrel, et al.              Standards Track                    [Page 10]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

3.3.  RRO Processing across Domains

   [RFC3209] defines the RRO as an optional object used for loop
   detection and for providing information about the hops traversed by
   LSPs.

   As described for overlay networks in [RFC4208], a domain border node
   MAY filter or modify the information provided in an RRO for
   confidentiality reasons according to local policy.  For example, a
   series of identifiers of hops within a domain MAY be replaced with
   the domain identifier (such as the AS number) or be removed entirely
   leaving just the domain border nodes.

   Note that a domain border router MUST NOT mask its own presence, and
   MUST include itself in the RRO.

   Such filtering of RRO information does not hamper the working of the
   signaling protocol, but the subsequent information loss may render
   management diagnostic procedures inoperable or at least make them
   more complicated, requiring the coordination of administrators of
   multiple domains.

   Similarly, protocol procedures that depend on the presence of RRO
   information may become inefficient.  For example, the Fast Reroute
   procedures defined in [RFC4090] use information in the RRO to
   determine the labels to use and the downstream MP.

3.4.  Notify Message Processing

   Notify messages are introduced in [RFC3473].  They may be sent direct
   rather than hop-by-hop, and so may speed the propagation of error
   information.  If a domain border router is interested in seeing such
   messages (for example, to enable it to provide protection switching),
   it is RECOMMENDED that the domain border router update the Notify
   Request objects in the Path and Resv messages to show its own address
   following the procedures of [RFC3473].

   Note that the replacement of a Notify Recipient in the Notify Request
   object means that some Notify messages (for example, those intended
   for delivery to the ingress LSR) may need to be examined, processed,
   and forwarded at domain borders.  This is an obvious trade-off issue
   as the ability to handle notifiable events locally (i.e., within the
   domain) may or may not outweigh the cost of processing and forwarding
   Notify messages beyond the domain.  Observe that the cost increases
   linearly with the number of domains in use.

Farrel, et al.              Standards Track                    [Page 11]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   Also note that, as described in Section 8, a domain administrator may
   wish to filter or modify Notify messages that are generated within a
   domain in order to preserve security or confidentiality of network
   information.  This is most easily achieved if the Notify messages are
   sent via the domain borders.

4.  RSVP-TE Signaling Extensions

   The following RSVP-TE signaling extensions are defined to enable
   inter-domain LSP setup.

4.1.  Control of Choice of Signaling Method

   In many network environments, there may be a network-wide policy that
   determines which one of the three inter-domain LSP techniques is
   used.  In these cases, no protocol extensions are required.

   However, in environments that support more than one technique, an
   ingress node may wish to constrain the choice made by domain border
   nodes for each inter-domain TE LSP that it originates.

   [RFC4420] defines the LSP_Attributes object that can be used to
   signal required attributes of an LSP.  The Attributes Flags TLV
   includes Boolean flags that define individual attributes.

   This document defines a new bit in the TLV that can be set by the
   ingress node of an inter-domain TE LSP to restrict the intermediate
   nodes to using contiguous signaling:

      Contiguous LSP bit (bit number assignment in Section 9.1)

   This flag is set by the ingress node that originates a Path message
   to set up an inter-domain TE LSP if it requires that the contiguous
   LSP technique is used.  This flag bit is only to be used in the
   Attributes Flags TLV.

   When a domain border LSR receives a Path message containing this bit
   set (one), the node MUST NOT perform stitching or nesting in support
   of the inter-domain TE LSP being set up.  When this bit is clear
   (zero), a domain border LSR MAY perform stitching or nesting
   according to local policy.

   This bit MUST NOT be modified by any transit node.

Farrel, et al.              Standards Track                    [Page 12]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   An intermediate node that supports the LSP_Attributes object and the
   Attributes Flags TLV, and also recognizes the "Contiguous LSP" bit,
   but cannot support contiguous TE LSPs, MUST send a Path Error message
   with an error code "Routing Problem"/"Contiguous LSP type not
   supported" if it receives a Path message with this bit set.

   If an intermediate node receiving a Path message with the "Contiguous
   LSP" bit set in the Flags field of the LSP_Attributes, recognizes the
   object, the TLV, and the bit and also supports the desired contiguous
   LSP behavior, then it MUST signal a contiguous LSP.  If the node is a
   domain border node, or if the node expands a loose hop in the ERO, it
   MUST include an RRO Attributes subobject in the RRO of the
   corresponding Resv message (if such an object is present) with the
   "Contiguous LSP" bit set to report its behavior.

   Domain border LSRs MUST support and act on the setting of the
   "Contiguous LSP" flag.

   However, if the intermediate node supports the LSP_Attributes object
   but does not recognize the Attributes Flags TLV, or supports the TLV
   but does not recognize this "Contiguous LSP" bit, then it MUST
   forward the object unmodified.

   The choice of action by an ingress node that receives a PathErr when
   requesting the use of a contiguous LSP is out of the scope of this
   document, but may include the computation of an alternate path.

5.  Protection and Recovery of Inter-Domain TE LSPs

   The procedures described in Sections 3 and 4 MUST be applied to all
   inter-domain TE LSPs, including bypass tunnels, detour LSPs
   [RFC4090], and segment recovery LSPs [RFC4873].  This means that
   these LSPs will also be subjected to ERO processing, policies, path
   computation, etc.

   Note also that the paths for these backup LSPs need to be either
   pre-configured, computed, and signaled with the protected LSP or
   computed on-demand at the PLR.  Just as with any inter-domain TE LSP,
   the ERO may comprise strict or loose hops and will depend on the TE
   visibility of the computation point into the subsequent domain.

   If loose hops are present in the path of the backup LSP, ERO
   expansion will be required at some point along the path: probably at
   a domain border node.  In order that the backup path remains disjoint
   from the protected LSP(s) the node performing the ERO expansion must

Farrel, et al.              Standards Track                    [Page 13]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   be provided with the path of the protected LSPs between the PLR and
   the MP.  This information can be gathered from the RROs of the
   protected LSPs and is signaled in the DETOUR object for Fast Reroute
   [RFC4090] and uses route exclusion [RFC4874] for other protection
   schemes.

5.1.  Fast Recovery Support Using MPLS-TE Fast Reroute (FRR)

   [RFC4090] describes two methods for local protection for a packet TE
   LSP in case of link, Shared Risk Link Group (SRLG), or node failure.
   This section describes how these mechanisms work with the proposed
   signaling solutions for inter-domain TE LSP setup.

5.1.1.  Failure within a Domain (Link or Node Failure)

   The mode of operation of MPLS-TE Fast Reroute to protect a
   contiguous, stitched, or nested TE LSP within a domain is identical
   to the existing procedures described in [RFC4090].  Note that, in the
   case of nesting or stitching, the end-to-end LSP is automatically
   protected by the protection operation performed on the H-LSP or
   stitching segment LSP.

   No protocol extensions are required.

5.1.2.  Failure of a Link at a Domain Border

   This case arises where two domains are connected by a TE link.  In
   this case, each domain has its own domain border node, and these two
   nodes are connected by the TE link.  An example of this case is where
   the ASBRs of two ASs are connected by a TE link.

   A contiguous LSP can be backed up using any PLR and MP, but if the
   LSP uses stitching or nesting in either of the connected domains, the
   PLR and MP MUST be domain border nodes for those domains.  It will be
   usual to attempt to use the local (connected by the failed link)
   domain border nodes as the PLR and MP.

   To protect an inter-domain link with MPLS-TE Fast Reroute, a set of
   backup tunnels must be configured or dynamically computed between the
   PLR and MP such that they are diversely routed from the protected
   inter-domain link and the protected inter-domain LSPs.

   Each protected inter-domain LSP using the protected inter-domain TE
   link must be assigned to an NHOP bypass tunnel that is diverse from
   the protected LSP.  Such an NHOP bypass tunnel can be selected by
   analyzing the RROs in the Resv messages of the available bypass

Farrel, et al.              Standards Track                    [Page 14]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   tunnels and the protected TE LSP.  It may be helpful to this process
   if the extensions defined in [RFC4561] are used to clearly
   distinguish nodes and links in the RROs.

5.1.3.  Failure of a Border Node

   Two border node failure cases exist.  If the domain border falls on a
   link as described in the previous section, the border node at either
   end of the link may fail.  Alternatively, if the border falls on a
   border node (as is the case with IGP areas), that single border node
   may fail.

   It can be seen that if stitching or nesting is used, the failed node
   will be the start or end (or both) of a stitching segment LSP or
   H-LSP, in which case protection must be provided to the far end of
   the stitching segment or H-LSP.  Thus, where one of these two
   techniques is in use, the PLR will be the upstream domain entry point
   in the case of the failure of the domain exit point, and the MP will
   be the downstream domain exit point in the case of the failure of the
   domain entry point.  Where the domain border falls at a single domain
   border node, both cases will apply.

   If the contiguous LSP mechanism is in use, normal selection of the
   PLR and MP can be applied, and any node within the domains may be
   used to fill these roles.

   As before, selection of a suitable backup tunnel (in this case, an
   NNHOP backup) must consider the paths of the backed-up LSPs and the
   available NNHOP tunnels by examination of their RROs.

   Note that where the PLR is not immediately upstream of the failed
   node, error propagation time may be delayed unless some mechanism
   such as [BFD-MPLS] is implemented or unless direct reporting, such as
   through the GMPLS Notify message [RFC3473], is employed.

5.2.  Protection and Recovery of GMPLS LSPs

   [RFC4873] describes GMPLS-based segment recovery.  This allows
   protection against a span failure, a node failure, or failure over
   any particular portion of a network used by an LSP.

   The domain border failure cases described in Section 5.1 may also
   occur in GMPLS networks (including packet networks) and can be
   protected against using segment protection without any additional
   protocol extensions.

Farrel, et al.              Standards Track                    [Page 15]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   Note that if loose hops are used in the construction of the working
   and protection paths signaled for segment protection, then care is
   required to keep these paths disjoint.  If the paths are signaled
   incrementally, then route exclusion [RFC4874] may be used to ensure
   that the paths are disjoint.  Otherwise, a coordinated path
   computation technique such as that offered by cooperating Path
   Computation Elements [RFC4655] can provide suitable paths.

6.  Reoptimization of Inter-Domain TE LSPs

   Reoptimization of a TE LSP is the process of moving the LSP from the
   current path to a more preferred path.  This involves the
   determination of the preferred path and make-before-break signaling
   procedures [RFC3209] to minimize traffic disruption.

   Reoptimization of an inter-domain TE LSP may require a new path in
   more than one domain.

   The nature of the inter-domain LSP setup mechanism defines how
   reoptimization can be applied.  If the LSP is contiguous, then the
   signaling of the make-before-break process MUST be initiated by the
   ingress node as defined in [RFC3209].  But if the reoptimization is
   limited to a change in path within one domain (that is, if there is
   no change to the domain border nodes) and nesting or stitching is in
   use, the H-LSP or stitching segment may be independently reoptimized
   within the domain without impacting the end-to-end LSP.

   In all cases, however, the ingress LSR may wish to exert control and
   coordination over the reoptimization process.  For example, a transit
   domain may be aware of the potential for reoptimization, but not
   bother because it is not worried by the level of service being
   provided across the domain.  But the cumulative effect on the
   end-to-end LSP may cause the head-end to worry and trigger an
   end-to-end reoptimization request (of course, the transit domain may
   choose to ignore the request).

   Another benefit of end-to-end reoptimization over per-domain
   reoptimization for non-contiguous inter-domain LSPs is that
   per-domain reoptimization is restricted to preserve the domain entry
   and exit points (since to do otherwise would break the LSP!).  But
   end-to-end reoptimization is more flexible and can select new domain
   border LSRs.

Farrel, et al.              Standards Track                    [Page 16]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   There may be different cost-benefit analysis considerations between
   end-to-end reoptimization and per-domain reoptimization.  The greater
   the number of hops involved in the reoptimization, the higher the
   risk of traffic disruption.  The shorter the segment reoptimized, the
   lower the chance of making a substantial improvement on the quality
   of the end-to-end LSP.  Administrative policies should be applied in
   this area with care.

   [RFC4736] describes mechanisms that allow:

   - The ingress node to request each node with a loose next hop to
     re-evaluate the current path in order to search for a more optimal
     path.

   - A node with a loose next hop to inform the ingress node that a
     better path exists.

   These mechanisms SHOULD be used for reoptimization of a contiguous
   inter-domain TE LSP.

   Note that end-to-end reoptimization may involve a non-local
   modification that might select new entry / exit points.  In this
   case, we can observe that local reoptimization is more easily and
   flexibly achieved using nesting or stitching.  Further, the "locality
   principle" (i.e., the idea of keeping information only where it is
   needed) is best achieved using stitching or nesting.  That said, a
   contiguous LSP can easily be modified to take advantage of local
   reoptimizations (as defined in [RFC4736]) even if this would require
   the dissemination of information and the invocation of signaling
   outside the local domain.

7.  Backward Compatibility

   The procedures in this document are backward compatible with existing
   deployments.

   - Ingress LSRs are not required to support the extensions in this
     document to provision intra-domain LSPs.  The default behavior by
     transit LSRs that receive a Path message that does not have the
     "Contiguous LSP" bit set in the Attributes Flags TLV of the
     LSP_Attributes object or does not even have the object present is
     to allow all modes of inter-domain TE LSP, so back-level ingress
     LSRs are able to initiate inter-domain LSPs.

   - Transit, non-border LSRs are not required to perform any special
     processing and will pass the LSP_Attributes object onwards
     unmodified according to the rules of [RFC2205].  Thus, back-level
     transit LSRs are fully supported.

Farrel, et al.              Standards Track                    [Page 17]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   - Domain border LSRs will need to be upgraded before inter-domain TE
     LSPs are allowed.  This is because of the need to establish policy,
     administrative, and security controls before permitting
     inter-domain LSPs to be signaled across a domain border.  Thus,
     legacy domain border LSRs do not need to be considered.

   The RRO additions in this document are fully backward compatible.

8.  Security Considerations

   RSVP does not currently provide for automated key management.
   [RFC4107] states a requirement for mandatory automated key management
   under certain situations.  There is work starting in the IETF to
   define improved authentication including automated key management for
   RSVP.  Implementations and deployments of RSVP should pay attention
   to any capabilities and requirements that are outputs from this
   ongoing work.

   A separate document is being prepared to examine the security aspects
   of RSVP-TE signaling with special reference to multi-domain scenarios
   [MPLS-SEC].  [RFC4726] provides an overview of the requirements for
   security in an MPLS-TE or GMPLS multi-domain environment.

   Before electing to utilize inter-domain signaling for MPLS-TE, the
   administrators of neighboring domains MUST satisfy themselves as to
   the existence of a suitable trust relationship between the domains.
   In the absence of such a relationship, the administrators SHOULD
   decide not to deploy inter-domain signaling, and SHOULD disable
   RSVP-TE on any inter-domain interfaces.

   When signaling an inter-domain RSVP-TE LSP, an operator MAY make use
   of the security features already defined for RSVP-TE [RFC3209].  This
   may require some coordination between the domains to share the keys
   (see [RFC2747] and [RFC3097]), and care is required to ensure that
   the keys are changed sufficiently frequently.  Note that this may
   involve additional synchronization, should the domain border nodes be
   protected with FRR, since the MP and PLR should also share the key.

   For an inter-domain TE LSP, especially when it traverses different
   administrative or trust domains, the following mechanisms SHOULD be
   provided to an operator (also see [RFC4216]):

   1) A way to enforce policies and filters at the domain borders to
      process the incoming inter-domain TE LSP setup requests (Path
      messages) based on certain agreed trust and service
      levels/contracts between domains.  Various LSP attributes such as
      bandwidth, priority, etc. could be part of such a contract.

Farrel, et al.              Standards Track                    [Page 18]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   2) A way for the operator to rate-limit LSP setup requests or error
      notifications from a particular domain.

   3) A mechanism to allow policy-based outbound RSVP message processing
      at the domain border node, which may involve filtering or
      modification of certain addresses in RSVP objects and messages.

   Additionally, an operator may wish to reduce the signaling
   interactions between domains to improve security.  For example, the
   operator might not trust the neighboring domain to supply correct or
   trustable restart information [RFC5063] and might ensure that the
   availability of restart function is not configured in the Hello
   message exchange across the domain border.  Thus, suitable
   configuration MUST be provided in an RSVP-TE implementation to enable
   the operator to control optional protocol features that may be
   considered a security risk.

   Some examples of the policies described above are as follows:

     A) An operator may choose to implement some kind of ERO filtering
        policy on the domain border node to disallow or ignore hops
        within the domain from being identified in the ERO of an
        incoming Path message.  That is, the policy is that a node
        outside the domain cannot specify the path of the LSP inside the
        domain.  The domain border LSR can make implement this policy in
        one of two ways:

          - It can reject the Path message.

          - It can ignore the hops in the ERO that lie within the
            domain.

     B) In order to preserve confidentiality of network topology, an
        operator may choose to disallow recording of hops within the
        domain in the RRO or may choose to filter out certain recorded
        RRO addresses at the domain border node.

     C) An operator may require the border node to modify the addresses
        of certain messages like PathErr or Notify originated from hops
        within the domain.

     D) In the event of a path computation failure, an operator may
        require the border node to silently discard the Path message
        instead of returning a PathErr.  This is because a Path message
        could be interpreted as a network probe, and a PathErr provides
        information about the network capabilities and policies.

Farrel, et al.              Standards Track                    [Page 19]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   Note that the detailed specification of such policies and their
   implementation are outside the scope of this document.

   Operations, Administration, and Management (OAM) mechanisms including
   [BFD-MPLS] and [RFC4379] are commonly used to verify the connectivity
   of end-to-end LSPs and to trace their paths.  Where the LSPs are
   inter-domain LSPs, such OAM techniques MAY require that OAM messages
   are intercepted or modified at domain borders, or are passed
   transparently across domains.  Further discussion of this topic can
   be found in [INTERAS-PING] and [MPLS-SEC].

9.  IANA Considerations

   IANA has made the codepoint allocations described in the following
   sections.

9.1.  Attribute Flags for LSP_Attributes Object

   A new bit has been allocated from the "Attributes Flags" sub-registry
   of the "RSVP TE Parameters" registry.

  Bit | Name                 | Attribute  | Path       | RRO | Reference
  No  |                      | Flags Path | Flags Resv |     |
  ----+----------------------+------------+------------+-----+----------
  4     Contiguous LSP         Yes          No           Yes   [RFC5150]

9.2.  New Error Codes

   New RSVP error codes/values have been allocated from the "Error Codes
   and Globally-Defined Error Value Sub-Codes" sub-registry of the "RSVP
   Parameters" registry.

   For the existing error code "Policy control failure" (value 2), two
   new error values have been registered as follows:

      103 = Inter-domain policy failure
      104 = Inter-domain explicit route rejected

   For the existing error code "Routing Problem" (value 24), two new
   error values have been registered as follows:

      28 = Contiguous LSP type not supported
      29 = ERO conflicts with inter-domain signaling method

Farrel, et al.              Standards Track                    [Page 20]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

10.  Acknowledgements

   The authors would like to acknowledge the input and helpful comments
   from Kireeti Kompella on various aspects discussed in the document.
   Deborah Brungard and Dimitri Papdimitriou provided thorough reviews.

   Thanks to Sam Hartman for detailed discussions of the security
   considerations.

11.  References

11.1.  Normative References

   [RFC2119]       Bradner, S., "Key words for use in RFCs to Indicate
                   Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC2205]       Braden, R., Ed., Zhang, L., Berson, S., Herzog, S.,
                   and S. Jamin, "Resource ReSerVation Protocol (RSVP)
                   -- Version 1 Functional Specification", RFC 2205,
                   September 1997.

   [RFC3209]       Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan,
                   V., and G. Swallow, "RSVP-TE: Extensions to RSVP for
                   LSP Tunnels", RFC 3209, December 2001.

   [RFC3473]       Berger, L., Ed., "Generalized Multi-Protocol Label
                   Switching (GMPLS) Signaling Resource ReserVation
                   Protocol-Traffic Engineering (RSVP-TE) Extensions",
                   RFC 3473, January 2003.

   [RFC4206]       Kompella, K. and Y. Rekhter, "Label Switched Paths
                   (LSP) Hierarchy with Generalized Multi-Protocol Label
                   Switching (GMPLS) Traffic Engineering (TE)", RFC
                   4206, October 2005.

   [RFC4420]       Farrel, A., Ed., Papadimitriou, D., Vasseur, J.-P.,
                   and A. Ayyangar, "Encoding of Attributes for
                   Multiprotocol Label Switching (MPLS) Label Switched
                   Path (LSP) Establishment Using Resource ReserVation
                   Protocol-Traffic Engineering (RSVP-TE)", RFC 4420,
                   February 2006.

   [RFC5150]       Ayyangar, A., Kompella, K., and JP. Vasseur, "Label
                   Switched Path Stitching with Generalized
                   Multiprotocol Label Switching Traffic Engineering
                   (GMPLS TE)", RFC 5150, February 2008.

Farrel, et al.              Standards Track                    [Page 21]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

11.2. Informative References

   [RFC2747]       Baker, F., Lindell, B., and M. Talwar, "RSVP
                   Cryptographic Authentication", RFC 2747, January
                   2000.

   [RFC3097]       Braden, R. and L. Zhang, "RSVP Cryptographic
                   Authentication -- Updated Message Type Value", RFC
                   3097, April 2001.

   [RFC4090]       Pan, P., Ed., Swallow, G., Ed., and A. Atlas, Ed.,
                   "Fast Reroute Extensions to RSVP-TE for LSP Tunnels",
                   RFC 4090, May 2005.

   [RFC4105]       Le Roux, J.-L., Ed., Vasseur, J.-P., Ed., and J.
                   Boyle, Ed., "Requirements for Inter-Area MPLS Traffic
                   Engineering", RFC 4105, June 2005.

   [RFC4107]       Bellovin, S. and R. Housley, "Guidelines for
                   Cryptographic Key Management", BCP 107, RFC 4107,
                   June 2005.

   [RFC4208]       Swallow, G., Drake, J., Ishimatsu, H., and Y.
                   Rekhter, "Generalized Multiprotocol Label Switching
                   (GMPLS) User-Network Interface (UNI): Resource
                   ReserVation Protocol-Traffic Engineering (RSVP-TE)
                   Support for the Overlay Model", RFC 4208, October
                   2005.

   [RFC4216]       Zhang, R., Ed., and J.-P. Vasseur, Ed., "MPLS Inter-
                   Autonomous System (AS) Traffic Engineering (TE)
                   Requirements", RFC 4216, November 2005.

   [RFC4379]       Kompella, K. and G. Swallow, "Detecting Multi-
                   Protocol Label Switched (MPLS) Data Plane Failures",
                   RFC 4379, February 2006.

   [RFC4561]       Vasseur, J.-P., Ed., Ali, Z., and S. Sivabalan,
                   "Definition of a Record Route Object (RRO) Node-Id
                   Sub-Object", RFC 4561, June 2006.

   [RFC4655]       Farrel, A., Vasseur, J.-P., and J. Ash, "A Path
                   Computation Element (PCE)-Based Architecture", RFC
                   4655, August 2006.

Farrel, et al.              Standards Track                    [Page 22]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

   [RFC4726]       Farrel, A., Vasseur, J.-P., and A. Ayyangar, "A
                   Framework for Inter-Domain Multiprotocol Label
                   Switching Traffic Engineering", RFC 4726, November
                   2006.

   [RFC4736]       Vasseur, JP., Ed., Ikejiri, Y., and R. Zhang,
                   "Reoptimization of Multiprotocol Label Switching
                   (MPLS) Traffic Engineering (TE) Loosely Routed Label
                   Switched Path (LSP)", RFC 4736, November 2006.

   [RFC4873]       Berger, L., Bryskin, I., Papadimitriou, D., and A.
                   Farrel, "GMPLS Segment Recovery", RFC 4873, May 2007.

   [RFC4874]       Lee, CY., Farrel, A., and S. De Cnodder, "Exclude
                   Routes - Extension to Resource ReserVation Protocol-
                   Traffic Engineering (RSVP-TE)", RFC 4874, April 2007.

   [RFC4920]       Farrel, A., Ed., Satyanarayana, A., Iwata, A.,
                   Fujita, N., and G. Ash, "Crankback Signaling
                   Extensions for MPLS and GMPLS RSVP-TE", RFC 4920,
                   July 2007.

   [BFD-MPLS]      Aggarwal, R., Kompella, K., Nadeau, T., and G.
                   Swallow, "BFD For MPLS LSPs", Work in Progress,
                   February 2005.

   [INTERAS-PING]  Nadeau, T. and G. Swallow, "Detecting MPLS Data Plane
                   Failures in Inter-AS and inter-provider Scenarios",
                   Work in Progress, October 2006.

   [RFC5152]       Vasseur, JP., Ed., Ayyangar, A., Ed., and R. Zhang,
                   "A Per-Domain Path Computation Method for
                   Establishing Inter-Domain Traffic Engineering (TE)
                   Label Switched Paths (LSPs)", RFC 5152, February
                   2008.

   [MPLS-SEC]      Fang, L., Ed., Behringer, M., Callon, R., Le Roux, J.
                   L., Zhang, R., Knight, P., Stein, Y., Bitar, N., and
                   R. Graveman., "Security Framework for MPLS and GMPLS
                   Networks", Work in Progress, July 2007.

   [RFC5063]       Satyanarayana, A., Ed., and R. Rahman, Ed.,
                   "Extensions to GMPLS Resource Reservation Protocol
                   (RSVP) Graceful Restart", RFC 5063, October 2007.

Farrel, et al.              Standards Track                    [Page 23]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

Authors' Addresses

   Adrian Farrel
   Old Dog Consulting

   EMail: adrian@olddog.co.uk

   Arthi Ayyangar
   Juniper Networks
   1194 N. Mathilda Avenue
   Sunnyvale, CA 94089
   USA

   EMail: arthi@juniper.net

   Jean Philippe Vasseur
   Cisco Systems, Inc.
   300 Beaver Brook Road
   Boxborough , MA - 01719
   USA

   EMail: jpv@cisco.com

Farrel, et al.              Standards Track                    [Page 24]
RFC 5151      Inter-Domain MPLS & GMPLS RSVP-TE Extensions February 2008

Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Farrel, et al.              Standards Track                    [Page 25]