Skip to main content

RTP Control Protocol (RTCP) Extended Report (XR) Block for MPEG2 Transport Stream (TS) Program Specific Information (PSI) Decodability Statistics Metrics reporting
draft-ietf-xrblock-rtcp-xr-psi-decodability-03

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 7380.
Authors Jiangang Tong, Claire Bi, Roni Even , Qin Wu , Rachel Huang
Last updated 2014-06-05 (Latest revision 2014-04-23)
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state Submitted to IESG for Publication
Document shepherd Dan Romascanu
Shepherd write-up Show Last changed 2014-05-19
IESG IESG state Became RFC 7380 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD Alissa Cooper
Send notices to xrblock-chairs@tools.ietf.org, draft-ietf-xrblock-rtcp-xr-psi-decodability@tools.ietf.org
draft-ietf-xrblock-rtcp-xr-psi-decodability-03
Network Working Group                                            J. Tong
Internet-Draft                                                C. Bi, Ed.
Intended status: Standards Track                           China Telecom
Expires: October 26, 2014                                        R. Even
                                                        Gesher Erove Ltd
                                                              Q. Wu, Ed.
                                                                R. Huang
                                                                  Huawei
                                                          April 24, 2014

    RTP Control Protocol (RTCP) Extended Report (XR) Block for MPEG2
 Transport Stream (TS) Program Specific Information (PSI) Decodability
                      Statistics Metrics reporting
             draft-ietf-xrblock-rtcp-xr-psi-decodability-03

Abstract

   An MPEG2 Transport Stream (TS) is a standard container format used in
   the transmission and storage of multimedia data.  Unicast/Multicast
   MPEG2 TS over RTP is widely deployed in IPTV systems.  This document
   defines an RTP Control Protocol (RTCP) Extended Report (XR) Block
   that allows the reporting of MPEG2 TS decodability statistics metrics
   related to transmissions of MPEG2 TS over RTP.  The metrics specified
   in the RTCP XR Block are related to Program specific information
   carried in MPEG TS.

Status of this Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at http://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on October 26, 2014.

Copyright Notice

   Copyright (c) 2014 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

Tong, et al.            Expires October 26, 2014                [Page 1]
Internet-Draft           RTCP XR TS Decodability              April 2014

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (http://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction . . . . . . . . . . . . . . . . . . . . . . . . .  3
     1.1.  MPEG2 Transport Stream Decodability Metrics  . . . . . . .  3
     1.2.  RTCP and RTCP XR Reports . . . . . . . . . . . . . . . . .  3
     1.3.  Performance Metrics Framework  . . . . . . . . . . . . . .  3
     1.4.  Applicability  . . . . . . . . . . . . . . . . . . . . . .  3
   2.  Terminology  . . . . . . . . . . . . . . . . . . . . . . . . .  4
     2.1.  Standards Language . . . . . . . . . . . . . . . . . . . .  4
   3.  MPEG2 TS PSI Decodability Statistics Metrics Block . . . . . .  4
   4.  SDP Signaling  . . . . . . . . . . . . . . . . . . . . . . . .  8
     4.1.  SDP rtcp-xr-attrib Attribute Extension . . . . . . . . . .  8
     4.2.  Offer/Answer Usage . . . . . . . . . . . . . . . . . . . .  8
     4.3.  Usage Outside of Offer/Answer  . . . . . . . . . . . . . .  8
   5.  IANA Considerations  . . . . . . . . . . . . . . . . . . . . .  8
     5.1.  New RTCP XR Block Type value . . . . . . . . . . . . . . .  8
     5.2.  New RTCP XR SDP Parameter  . . . . . . . . . . . . . . . .  9
     5.3.  Contact information for registrations  . . . . . . . . . .  9
   6.  Security Considerations  . . . . . . . . . . . . . . . . . . .  9
   7.  References . . . . . . . . . . . . . . . . . . . . . . . . . .  9
     7.1.  Normative References . . . . . . . . . . . . . . . . . . .  9
     7.2.  Informative References . . . . . . . . . . . . . . . . . . 10
   Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 10

Tong, et al.            Expires October 26, 2014                [Page 2]
Internet-Draft           RTCP XR TS Decodability              April 2014

1.  Introduction

1.1.  MPEG2 Transport Stream Decodability Metrics

   The European Telecommunications Standards Institute (ETSI) has
   defined a set of syntax and information consistency tests and
   corresponding indicators [ETSI] that are recommended for the
   monitoring of MPEG2 Transport Streams [ISO-IEC.13818-1.2007].  The
   tests and corresponding indicators are grouped according to priority:

   o  First priority - Necessary for decodability (basic monitoring)
   o  Second priority - Recommended for continuous or periodic
      monitoring
   o  Third priority - Recommended for application-dependent monitoring

   This memo is based on information consistency tests and resulting
   indicators defined by ETSI [ETSI] and defines a new block type to
   augment those defined in [RFC3611] for use with MPEG2 Transport
   Stream (TS) [ISO-IEC.13818-1.2007].  The new block type supports
   reporting of the number of occurrences of each Program Specific
   Information (PSI) indicator in the first and second priorities that
   supplements information from PSI independent Decodability Statistics
   Metrics Block [RFC6990]; third priority indicators are not supported.

1.2.  RTCP and RTCP XR Reports

   The use of RTCP for reporting is defined in [RFC3550].  [RFC3611]
   defined an extensible structure for reporting using an RTCP Extended
   Report (XR).  This document defines a new Extended Report block for
   use with [RFC3550] and [RFC3611].

1.3.  Performance Metrics Framework

   The Performance Metrics Framework [RFC6390] provides guidance on the
   definition and specification of performance metrics.  The RTP
   Monitoring Architectures [RFC6792] provides guideline for reporting
   block format using RTCP XR.  The new report block described in this
   memo is in compliance with the monitoring architecture specified in
   [RFC6792] and the Performance Metrics Framework [RFC6390].

1.4.  Applicability

   These metrics are applicable to any type of RTP application that uses
   the MPEG2 TS standard format for multimedia data; for example, MPEG4
   over MPEG2 TS over RTP.  This new block type can be useful for
   measuring content stream or TS quality by checking TS header
   information [ETSI] and identifying the existence, and characterizing
   the severity, of bitstream packetization problems which may affect

Tong, et al.            Expires October 26, 2014                [Page 3]
Internet-Draft           RTCP XR TS Decodability              April 2014

   users' perception of a service delivered over RTP; it may also be
   useful for verifying the continued correct operation of an existing
   system management tool.

2.  Terminology

2.1.  Standards Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

3.  MPEG2 TS PSI Decodability Statistics Metrics Block

   ETSI TR 101290 [ETSI] generally defines metrics related to error
   events while this document contains counts of those metrics defined
   in [ETSI].  The block defined in this document reports MPEG2 TS PSI
   decodability statistics metrics beyond the information carried in the
   standard RTCP packet format and PSI independent Decodability Metrics
   Block [RFC6990], which are measured at the receiving end of the RTP
   stream.  It contains counts of six metrics defined in ETSI TR 101290
   [ETSI].  Information is reported about basic monitoring parameters
   necessary to ensure that the TS can be decoded including:

   o  Program Association Table(PAT) errors
   o  PAT 2 errors
   o  Program Map Table(PMT) errors
   o  PMT 2 errors
   o  Packet Identifier(PID) errors

   and continuous monitoring parameters necessary to ensure the
   continuous decoding including:

   o  Cyclic Redundancy Check (CRC) errors
   o  Conditional Access Table (CAT) errors

   The other parameters are ignored since they do not apply to all MPEG2
   implementations.  For further information on these parameters, see
   [ETSI].

   The MPEG2 TS PSI Decodability Metrics Block has the following format:

Tong, et al.            Expires October 26, 2014                [Page 4]
Internet-Draft           RTCP XR TS Decodability              April 2014

       0                   1                   2                   3
       0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |    BT=MTPD    |    Reserved   |         block length          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |                     SSRC of source                            |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |          begin_seq            |             end_seq           |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |        PAT_error_count        |      PAT_error_2_count        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |        PMT_error_count        |      PMT_error_2_count        |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |       PID_error_count         |      CRC_error_count          |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
      |        CAT_error_count        |        Reserved               |
      +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   block type (BT): 8 bits

      The MPEG2 TS PSI Decodability Metrics Block is identified by the
      constant <MTPD>.

   Reserved: 8 bits

      These bits are reserved.  They MUST be set to zero by senders
      ignored by receivers (See [RFC6709] section 4.2).

   block length: 16 bits

      The constant 6, in accordance with the definition of this field in
      Section 3 of RFC 3611.  The block MUST be discarded if the block
      length is set to a different value.

   SSRC of source: 32 bits

      As defined in Section 4.1 of RFC 3611.

   begin_seq: 16 bits

      As defined in Section 4.1 of RFC 3611.

   end_seq: 16 bits

      As defined in Section 4.1 of RFC 3611.

Tong, et al.            Expires October 26, 2014                [Page 5]
Internet-Draft           RTCP XR TS Decodability              April 2014

   PAT_error_count: 16 bits

      A count of the number of PAT errors that occurred in the above
      sequence number interval.  The program association table (PAT) is
      the only packet with packet ID (PID) 0x 0000.  A PAT error occurs
      when it does not occur at least every 0.5s or the table has an ID
      other than 0x 00, as defined in section 5.2.1 of [ETSI].  Every
      program within the MPEG TS stream is listed in the PAT; if it is
      missing, then no programs can be decoded.

      The measured value is unsigned value.  If the measurement is
      unavailable, the value 0xFFFF MUST be reported.  Note that
      PAT_error_count and PAT_error_2_count MUST NOT be reported at the
      same time in the same metric block.  If PAT_error_count is
      reported, PAT_error_2_count MUST be set to 0xFFFF.

   PAT_error_2_count: 16 bits

      A count of the number of PAT2 errors that occurred in the above
      sequence number interval.  A PAT2 error occurs when it does not
      occur at least every 0.5s or the table has an ID other than 0x 00
      or there is more than one table ID 0x 00 inside the packet with
      the PAT PID, as defined in section 5.2.1 of [ETSI].

      The measured value is unsigned value.  If the measurement is
      unavailable, the value 0xFFFF MUST be reported.  Note that
      PAT_error_count and PAT_error_2_count MUST NOT be reported at the
      same time in the same metric block.  If PAT_error_2_count is
      reported, PAT_error_count MUST be set to 0xFFFF.

   PMT_error_count: 16 bits

      A count of the number of PMT_errors that occurred in the above
      sequence number interval.  A PMT_error occurs when the program map
      table (PMT) does not come up at least every 0.5s on the PID that
      is referred to in the PAT, as defined in the section 5.2.1 of
      [ETSI].

      The measured value is unsigned value.  If the measurement is
      unavailable, the value 0xFFFF MUST be reported.  Note that
      PMT_error_count and PMT_error_2_count MUST NOT be reported at the
      same time in the same metric block.  If PMT_error_count is
      reported, PMT_error_2_count MUST be set to 0xFFFF.

Tong, et al.            Expires October 26, 2014                [Page 6]
Internet-Draft           RTCP XR TS Decodability              April 2014

   PMT_error_2_count: 16 bits

      A count of the number of PMT2 errors that occurred in the above
      sequence number interval.  A PMT2_error occurs when the program
      map table (PMT) does not come up at least every 0.5s on the PID
      that is referred to in the PAT, as defined in the section 5.2.1 of
      [ETSI].

      The measured value is unsigned value.  If the measurement is
      unavailable, the value 0xFFFF MUST be reported.  Note that
      PMT_error_count and PMT_error_2_count MUST NOT be reported at the
      same time in the same metric block.  If PMT_error_2_count is
      reported, PMT_error_count MUST be set to 0xFFFF.

   PID_error_count: 16 bits

      A count of the number of PID_errors that occurred in the above
      sequence number interval.  A PID_error occurs when MPEG TS streams
      are remultiplexed and any PID doesn't refer to an actual data
      stream, as defined in the section 5.2.2 of [ETSI].

      The measured value is unsigned value.  If the measurement is
      unavailable, the value 0xFFFF MUST be reported.

   CRC_error_count: 16 bits

      A count of the number of CRC_errors that occurred in the above
      sequence number interval.  A CRC_error occurs if data corruption
      occurred in any of the following tables -- CAT, PAT, PMT, Network
      Information Table (NIT), Event Information Table (EIT), Bouquet
      Association Table (BAT), Service Description Table (SDT) or Time
      Offset Table (TOT), as defined in the section 5.2.2 of [ETSI].

      The measured value is unsigned value.  If the measurement is
      unavailable, the value 0xFFFF MUST be reported.

   CAT_error_count: 16 bits

      A count of the number of CAT_errors that occurred in the above
      sequence number interval.  A CAT_error occurs when the table has
      an ID other than 0x 01,as defined in the section 5.2.2 of [ETSI].

      The measured value is unsigned value.  If the measurement is
      unavailable, the value 0xFFFF MUST be reported.

Tong, et al.            Expires October 26, 2014                [Page 7]
Internet-Draft           RTCP XR TS Decodability              April 2014

   Reserved: 16 bits

      These bits are reserved.  They MUST be set to zero by senders
      ignored by receivers (See [RFC6709] section 4.2).

4.  SDP Signaling

   RFC 3611 defines the use of SDP (Session Description Protocol)
   [RFC4566] for signaling the use of RTCP XR blocks.  However XR blocks
   MAY be used without prior signaling (See section 5 of RFC3611).

4.1.  SDP rtcp-xr-attrib Attribute Extension

   This session augments the SDP attribute "rtcp-xr" defined in Section
   5.1 of RFC 3611 by providing an additional value of "xr-format" to
   signal the use of the report block defined in this document.

   xr-format =/  xr-tpd-block

   xr-tpd-block = "ts-psi-decodability"

4.2.  Offer/Answer Usage

   When SDP is used in offer-answer context, the SDP Offer/Answer usage
   defined in [RFC3611] for unilateral "rtcp-xr" attribute parameters
   applies.  For detailed usage of Offer/Answer for unilateral
   parameter, refer to section 5.2 of [RFC3611].

4.3.  Usage Outside of Offer/Answer

   For usage outside of Offer/Answer,refer to section 5.3 of [RFC3611].

5.  IANA Considerations

   New report block types for RTCP XR are subject to IANA registration.
   For general guidelines on IANA allocations for RTCP XR, refer to
   Section 6.2 of RFC 3611.

5.1.  New RTCP XR Block Type value

   This document assigns the block type value MTPD in the IANA " RTP
   Control Protocol Extended Reports (RTCP XR) Block Type Registry " to
   the "MPEG2 Transport Stream PSI Decodability Statistics Metrics
   Block".

Tong, et al.            Expires October 26, 2014                [Page 8]
Internet-Draft           RTCP XR TS Decodability              April 2014

   [Note to RFC Editor: please replace MTPD with the IANA provided RTCP
   XR block type for this block.]

5.2.  New RTCP XR SDP Parameter

   This document also registers a new parameter "ts-psi-decodability" in
   the "RTP Control Protocol Extended Reports (RTCP XR) Session
   Description Protocol (SDP) Parameters Registry".

5.3.  Contact information for registrations

   The contact information for the registrations is:

                    Qin Wu
                    sunseawq@huawei.com
                    101 Software Avenue, Yuhua District
                    Nanjing, JiangSu 210012 China

6.  Security Considerations

   This proposed RTCP XR report block introduces no new security
   considerations beyond those described in RFC 3611.

7.  References

7.1.  Normative References

   [ETSI]     ETSI, "Digital Video Broadcasting (DVB); Measurement
              guidelines for DVB systems", Technical Report TR 101 290,
              2001.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3550]  Schulzrinne, H., "RTP: A Transport Protocol for Real-Time
              Applications", RFC 3550, July 2003.

   [RFC3611]  Friedman, T., Caceres, R., and A. Clark, "RTP Control
              Protocol Extended Reports (RTCP XR)", RFC 3611,
              November 2003.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, July 2006.

Tong, et al.            Expires October 26, 2014                [Page 9]
Internet-Draft           RTCP XR TS Decodability              April 2014

7.2.  Informative References

   [ISO-IEC.13818-1.2007]
              International Organization for Standardization,
              "Information technology - Generic coding of moving
              pictures and associated audio information: Systems",
              ISO International Standard 13818-1, October 2007.

   [RFC6390]  Clark, A. and B. Claise, "Guidelines for Considering New
              Performance Metric Development", BCP 170, RFC 6390,
              October 2011.

   [RFC6709]  Carpenter, B., Aboba, B., and S. Cheshire, "Design
              Considerations for Protocol Extensions", RFC 6709,
              September 2012.

   [RFC6792]  Wu, Q., Hunt, G., and P. Arden, "Guidelines for Use of the
              RTP Monitoring Framework", RFC 6792, November 2012.

   [RFC6990]  Wu, Q., "RTP Control Protocol (RTCP) Extended Report (XR)
              Block for MPEG2 Transport Stream (TS) Program Specific
              Information (PSI) Independent Decodability Statistics
              Metrics reporting", RFC 6990, May 2013.

Authors' Addresses

   Jiangang Tong
   Shanghai Research Institure of China Telecom Corporation Limited
   No.1835,South Pudong Road
   Shanghai  200122
   China

   Email: tongjg@sttri.com.cn

   Claire Bi (editor)
   Shanghai Research Institure of China Telecom Corporation Limited
   No.1835,South Pudong Road
   Shanghai  200122
   China

   Email: bijy@sttri.com.cn

Tong, et al.            Expires October 26, 2014               [Page 10]
Internet-Draft           RTCP XR TS Decodability              April 2014

   Roni Even
   Gesher Erove Ltd
   14 David Hamelech
   Tel Aviv  64953
   Israel

   Email: ron.even.tlv@gmail.com

   Qin Wu (editor)
   Huawei
   101 Software Avenue, Yuhua District
   Nanjing, Jiangsu  210012
   China

   Email: bill.wu@huawei.com

   Rachel Huang
   Huawei
   101 Software Avenue, Yuhua District
   Nanjing, Jiangsu  210012
   China

   Email: rachel.huang@huawei.com

Tong, et al.            Expires October 26, 2014               [Page 11]