Skip to main content

RTP Payload Format for Flexible Forward Error Correction (FEC)
draft-ietf-payload-flexible-fec-scheme-06

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8627.
Authors Mo Zanaty , Varun Singh , Ali C. Begen , Giridhar Mandyam
Last updated 2018-03-05
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Revised I-D Needed - Issue raised by WGLC
Document shepherd Roni Even
IESG IESG state Became RFC 8627 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to "Roni Even" <roni.even@mail01.huawei.com>
draft-ietf-payload-flexible-fec-scheme-06
PAYLOAD                                                        M. Zanaty
Internet-Draft                                                     Cisco
Intended status: Standards Track                                V. Singh
Expires: September 6, 2018                                  callstats.io
                                                                A. Begen
                                                         Networked Media
                                                              G. Mandyam
                                              Qualcomm Innovation Center
                                                           March 5, 2018

     RTP Payload Format for Flexible Forward Error Correction (FEC)
               draft-ietf-payload-flexible-fec-scheme-06

Abstract

   This document defines new RTP payload formats for the Forward Error
   Correction (FEC) packets that are generated by the non-interleaved
   and interleaved parity codes from a source media encapsulated in RTP.
   These parity codes are systematic codes, where a number of FEC repair
   packets are generated from a set of source packets.  These repair
   packets are sent in a redundancy RTP stream separate from the source
   RTP stream that carries the source packets.  RTP source packets that
   were lost in transmission can be reconstructed using the source and
   repair packets that were received.  The non-interleaved and
   interleaved parity codes which are defined in this specification
   offer a good protection against random and bursty packet losses,
   respectively, at a cost of decent complexity.  The RTP payload
   formats that are defined in this document address the scalability
   issues experienced with the earlier specifications including RFC
   2733, RFC 5109 and SMPTE 2022-1, and offer several improvements.  Due
   to these changes, the new payload formats are not backward compatible
   with the earlier specifications, but endpoints that do not implement
   this specification can still work by simply ignoring the FEC repair
   packets.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any

Zanaty, et al.          Expires September 6, 2018               [Page 1]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on September 6, 2018.

Copyright Notice

   Copyright (c) 2018 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
     1.1.  Parity Codes  . . . . . . . . . . . . . . . . . . . . . .   4
       1.1.1.  1-D Non-interleaved (Row) FEC Protection  . . . . . .   5
       1.1.2.  1-D Interleaved (Column) FEC Protection . . . . . . .   5
       1.1.3.  Use Cases for 1-D FEC Protection  . . . . . . . . . .   6
       1.1.4.  2-D (Row and Column) FEC Protection . . . . . . . . .   8
       1.1.5.  Overhead Computation  . . . . . . . . . . . . . . . .   9
   2.  Requirements Notation . . . . . . . . . . . . . . . . . . . .   9
   3.  Definitions and Notations . . . . . . . . . . . . . . . . . .  10
     3.1.  Definitions . . . . . . . . . . . . . . . . . . . . . . .  10
     3.2.  Notations . . . . . . . . . . . . . . . . . . . . . . . .  10
   4.  Packet Formats  . . . . . . . . . . . . . . . . . . . . . . .  10
     4.1.  Source Packets  . . . . . . . . . . . . . . . . . . . . .  10
     4.2.  Repair Packets  . . . . . . . . . . . . . . . . . . . . .  10
   5.  Payload Format Parameters . . . . . . . . . . . . . . . . . .  16
     5.1.  Media Type Registration - Parity Codes  . . . . . . . . .  16
       5.1.1.  Registration of audio/flexfec . . . . . . . . . . . .  16
       5.1.2.  Registration of video/flexfec . . . . . . . . . . . .  18
       5.1.3.  Registration of text/flexfec  . . . . . . . . . . . .  19
       5.1.4.  Registration of application/flexfec . . . . . . . . .  20
     5.2.  Mapping to SDP Parameters . . . . . . . . . . . . . . . .  22
       5.2.1.  Offer-Answer Model Considerations . . . . . . . . . .  22
       5.2.2.  Declarative Considerations  . . . . . . . . . . . . .  23
   6.  Protection and Recovery Procedures - Parity Codes . . . . . .  23
     6.1.  Overview  . . . . . . . . . . . . . . . . . . . . . . . .  23
     6.2.  Repair Packet Construction  . . . . . . . . . . . . . . .  24

Zanaty, et al.          Expires September 6, 2018               [Page 2]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

     6.3.  Source Packet Reconstruction  . . . . . . . . . . . . . .  25
       6.3.1.  Associating the Source and Repair Packets . . . . . .  26
       6.3.2.  Recovering the RTP Header . . . . . . . . . . . . . .  27
       6.3.3.  Recovering the RTP Payload  . . . . . . . . . . . . .  28
       6.3.4.  Iterative Decoding Algorithm for the 2-D Parity FEC
               Protection  . . . . . . . . . . . . . . . . . . . . .  29
   7.  SDP Examples  . . . . . . . . . . . . . . . . . . . . . . . .  31
     7.1.  Example SDP for Flexible FEC Protection with in-band SSRC
           mapping . . . . . . . . . . . . . . . . . . . . . . . . .  31
     7.2.  Example SDP for Flex FEC Protection with explicit
           signalling in the SDP . . . . . . . . . . . . . . . . . .  31
   8.  Congestion Control Considerations . . . . . . . . . . . . . .  32
   9.  Security Considerations . . . . . . . . . . . . . . . . . . .  33
   10. IANA Considerations . . . . . . . . . . . . . . . . . . . . .  33
   11. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . .  33
   12. Change Log  . . . . . . . . . . . . . . . . . . . . . . . . .  33
     12.1.  draft-ietf-payload-flexible-fec-scheme-05  . . . . . . .  34
     12.2.  draft-ietf-payload-flexible-fec-scheme-03  . . . . . . .  34
     12.3.  draft-ietf-payload-flexible-fec-scheme-02  . . . . . . .  34
     12.4.  draft-ietf-payload-flexible-fec-scheme-01  . . . . . . .  34
     12.5.  draft-ietf-payload-flexible-fec-scheme-00  . . . . . . .  34
     12.6.  draft-singh-payload-1d2d-parity-scheme-00  . . . . . . .  34
     12.7.  draft-ietf-fecframe-1d2d-parity-scheme-00  . . . . . . .  35
   13. References  . . . . . . . . . . . . . . . . . . . . . . . . .  35
     13.1.  Normative References . . . . . . . . . . . . . . . . . .  35
     13.2.  Informative References . . . . . . . . . . . . . . . . .  36
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  37

1.  Introduction

   This document defines new RTP payload formats for the Forward Error
   Correction (FEC) that is generated by the non-interleaved and
   interleaved parity codes from a source media encapsulated in RTP
   [RFC3550].  The type of the source media protected by these parity
   codes can be audio, video, text or application.  The FEC data are
   generated according to the media type parameters, which are
   communicated out-of-band (e.g., in SDP).  Furthermore, the
   associations or relationships between the source and repair RTP
   streams may be communicated in-band or out-of-band.  For situations
   where adaptivitiy of FEC parameters is desired, the endpoint can use
   the in-band mechanism, whereas when the FEC parameters are fixed, the
   endpoint may prefer to negotiate them out-of-band.

   The Redunadncy RTP Stream [RFC7656] repair packets proposed in this
   document protect the Source RTP Stream packets that belong to the
   same RTP session.

Zanaty, et al.          Expires September 6, 2018               [Page 3]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

1.1.  Parity Codes

   Both the non-interleaved and interleaved parity codes use the
   eXclusive OR (XOR) operation to generate the repair packets.  In a
   nutshell, the following steps take place:

   1.  The sender determines a set of source packets to be protected by
       FEC based on the media type parameters.

   2.  The sender applies the XOR operation on the source packets to
       generate the required number of repair packets.

   3.  The sender sends the repair packet(s) along with the source
       packets, in different RTP streams, to the receiver(s).  The
       repair packets may be sent proactively or on-demand based on RTCP
       feedback messages such as NACK [RFC4585].

   At the receiver side, if all of the source packets are successfully
   received, there is no need for FEC recovery and the repair packets
   are discarded.  However, if there are missing source packets, the
   repair packets can be used to recover the missing information.
   Figure 1 and Figure 2 describe example block diagrams for the
   systematic parity FEC encoder and decoder, respectively.

                              +------------+
   +--+  +--+  +--+  +--+ --> | Systematic | --> +--+  +--+  +--+  +--+
   +--+  +--+  +--+  +--+     | Parity FEC |     +--+  +--+  +--+  +--+
                              |  Encoder   |
                              |  (Sender)  | --> +==+  +==+
                              +------------+     +==+  +==+

   Source Packet: +--+    Repair Packet: +==+
                  +--+                   +==+

         Figure 1: Block diagram for systematic parity FEC encoder

                              +------------+
   +--+    X    X    +--+ --> | Systematic | --> +--+  +--+  +--+  +--+
   +--+              +--+     | Parity FEC |     +--+  +--+  +--+  +--+
                              |  Decoder   |
               +==+  +==+ --> | (Receiver) |
               +==+  +==+     +------------+

   Source Packet: +--+    Repair Packet: +==+    Lost Packet: X
                  +--+                   +==+

         Figure 2: Block diagram for systematic parity FEC decoder

Zanaty, et al.          Expires September 6, 2018               [Page 4]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   In Figure 2, it is clear that the FEC repair packets have to be
   received by the endpoint within a certain amount of time for the FEC
   recovery process to be useful.  In this document, we refer to the
   time that spans a FEC block, which consists of the source packets and
   the corresponding repair packets, as the repair window.  At the
   receiver side, the FEC decoder SHOULD buffer source and repair
   packets at least for the duration of the repair window, to allow all
   the repair packets to arrive.  The FEC decoder can start decoding the
   already received packets sooner; however, it should not register a
   FEC decoding failure until it waits at least for the duration of the
   repair window.

1.1.1.  1-D Non-interleaved (Row) FEC Protection

   Suppose that we have a group of D x L source packets that have
   sequence numbers starting from 1 running to D x L, and a repair
   packet is generated by applying the XOR operation to every L
   consecutive packets as sketched in Figure 3.  This process is
   referred to as 1-D non-interleaved FEC protection.  As a result of
   this process, D repair packets are generated, which we refer to as
   non-interleaved (or row) FEC repair packets.

   +--------------------------------------------------+    ---    +===+
   | S_1          S_2          S3          ...  S_L   | + |XOR| = |R_1|
   +--------------------------------------------------+    ---    +===+
   +--------------------------------------------------+    ---    +===+
   | S_L+1        S_L+2        S_L+3       ...  S_2xL | + |XOR| = |R_2|
   +--------------------------------------------------+    ---    +===+
     .            .            .                .           .       .
     .            .            .                .           .       .
     .            .            .                .           .       .
   +--------------------------------------------------+    ---    +===+
   | S_(D-1)xL+1  S_(D-1)xL+2  S_(D-1)xL+3 ...  S_DxL | + |XOR| = |R_D|
   +--------------------------------------------------+    ---    +===+

       Figure 3: Generating non-interleaved (row) FEC repair packets

1.1.2.  1-D Interleaved (Column) FEC Protection

   If we apply the XOR operation to the group of the source packets
   whose sequence numbers are L apart from each other, as sketched in
   Figure 4.  In this case the endpoint generates L repair packets.
   This process is referred to as 1-D interleaved FEC protection, and
   the resulting L repair packets are referred to as interleaved (or
   column) FEC repair packets.

Zanaty, et al.          Expires September 6, 2018               [Page 5]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

       +-------------+ +-------------+ +-------------+     +-------+
       | S_1         | | S_2         | | S3          | ... | S_L   |
       | S_L+1       | | S_L+2       | | S_L+3       | ... | S_2xL |
       | .           | | .           | |             |     |       |
       | .           | | .           | |             |     |       |
       | .           | | .           | |             |     |       |
       | S_(D-1)xL+1 | | S_(D-1)xL+2 | | S_(D-1)xL+3 | ... | S_DxL |
       +-------------+ +-------------+ +-------------+     +-------+
              +               +               +                +
        -------------   -------------   -------------       -------
       |     XOR     | |     XOR     | |     XOR     | ... |  XOR  |
        -------------   -------------   -------------       -------
              =               =               =                =
            +===+           +===+           +===+            +===+
            |C_1|           |C_2|           |C_3|      ...   |C_L|
            +===+           +===+           +===+            +===+

       Figure 4: Generating interleaved (column) FEC repair packets

1.1.3.  Use Cases for 1-D FEC Protection

   A sender may generate one non-interleaved repair packet out of L
   consecutive source packets or one interleaved repair packet out of D
   non-consecutive source packets.  Regardless of whether the repair
   packet is a non-interleaved or an interleaved one, it can provide a
   full recovery of the missing information if there is only one packet
   missing among the corresponding source packets.  This implies that
   1-D non-interleaved FEC protection performs better when the source
   packets are randomly lost.  However, if the packet losses occur in
   bursts, 1-D interleaved FEC protection performs better provided that
   L is chosen large enough, i.e., L-packet duration is not shorter than
   the observed burst duration.  If the sender generates non-interleaved
   FEC repair packets and a burst loss hits the source packets, the
   repair operation fails.  This is illustrated in Figure 5.

Zanaty, et al.          Expires September 6, 2018               [Page 6]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

                     +---+                +---+  +===+
                     | 1 |    X      X    | 4 |  |R_1|
                     +---+                +---+  +===+

                     +---+  +---+  +---+  +---+  +===+
                     | 5 |  | 6 |  | 7 |  | 8 |  |R_2|
                     +---+  +---+  +---+  +---+  +===+

                     +---+  +---+  +---+  +---+  +===+
                     | 9 |  | 10|  | 11|  | 12|  |R_3|
                     +---+  +---+  +---+  +---+  +===+

    Figure 5: Example scenario where 1-D non-interleaved FEC protection
                     fails error recovery (Burst Loss)

   The sender may generate interleaved FEC repair packets to combat with
   the bursty packet losses.  However, two or more random packet losses
   may hit the source and repair packets in the same column.  In that
   case, the repair operation fails as well.  This is illustrated in
   Figure 6.  Note that it is possible that two burst losses may occur
   back-to-back, in which case interleaved FEC repair packets may still
   fail to recover the lost data.

                        +---+         +---+  +---+
                        | 1 |    X    | 3 |  | 4 |
                        +---+         +---+  +---+

                        +---+         +---+  +---+
                        | 5 |    X    | 7 |  | 8 |
                        +---+         +---+  +---+

                        +---+  +---+  +---+  +---+
                        | 9 |  | 10|  | 11|  | 12|
                        +---+  +---+  +---+  +---+

                        +===+  +===+  +===+  +===+
                        |C_1|  |C_2|  |C_3|  |C_4|
                        +===+  +===+  +===+  +===+

   Figure 6: Example scenario where 1-D interleaved FEC protection fails
                      error recovery (Periodic Loss)

Zanaty, et al.          Expires September 6, 2018               [Page 7]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

1.1.4.  2-D (Row and Column) FEC Protection

   In networks where the source packets are lost both randomly and in
   bursts, the sender ought to generate both non-interleaved and
   interleaved FEC repair packets.  This type of FEC protection is known
   as 2-D parity FEC protection.  At the expense of generating more FEC
   repair packets, thus increasing the FEC overhead, 2-D FEC provides
   superior protection against mixed loss patterns.  However, it is
   still possible for 2-D parity FEC protection to fail to recover all
   of the lost source packets if a particular loss pattern occurs.  An
   example scenario is illustrated in Figure 7.

                     +---+                +---+  +===+
                     | 1 |    X      X    | 4 |  |R_1|
                     +---+                +---+  +===+

                     +---+  +---+  +---+  +---+  +===+
                     | 5 |  | 6 |  | 7 |  | 8 |  |R_2|
                     +---+  +---+  +---+  +---+  +===+

                     +---+                +---+  +===+
                     | 9 |    X      X    | 12|  |R_3|
                     +---+                +---+  +===+

                     +===+  +===+  +===+  +===+
                     |C_1|  |C_2|  |C_3|  |C_4|
                     +===+  +===+  +===+  +===+

    Figure 7: Example scenario #1 where 2-D parity FEC protection fails
                              error recovery

   2-D parity FEC protection also fails when at least two rows are
   missing a source and the FEC packet and the missing source packets
   (in at least two rows) are aligned in the same column.  An example
   loss pattern is sketched in Figure 8.  Similarly, 2-D parity FEC
   protection cannot repair all missing source packets when at least two
   columns are missing a source and the FEC packet and the missing
   source packets (in at least two columns) are aligned in the same row.

Zanaty, et al.          Expires September 6, 2018               [Page 8]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

                     +---+  +---+         +---+
                     | 1 |  | 2 |    X    | 4 |    X
                     +---+  +---+         +---+

                     +---+  +---+  +---+  +---+  +===+
                     | 5 |  | 6 |  | 7 |  | 8 |  |R_2|
                     +---+  +---+  +---+  +---+  +===+

                     +---+  +---+         +---+
                     | 9 |  | 10|    X    | 12|    X
                     +---+  +---+         +---+

                     +===+  +===+  +===+  +===+
                     |C_1|  |C_2|  |C_3|  |C_4|
                     +===+  +===+  +===+  +===+

    Figure 8: Example scenario #2 where 2-D parity FEC protection fails
                              error recovery

1.1.5.  Overhead Computation

   The overhead is defined as the ratio of the number of bytes belonging
   to the repair packets to the number of bytes belonging to the
   protected source packets.

   Generally, repair packets are larger in size compared to the source
   packets.  Also, not all the source packets are necessarily equal in
   size.  However, if we assume that each repair packet carries an equal
   number of bytes carried by a source packet, we can compute the
   overhead for different FEC protection methods as follows:

   o  1-D Non-interleaved FEC Protection: Overhead = 1/L

   o  1-D Interleaved FEC Protection: Overhead = 1/D

   o  2-D Parity FEC Protection: Overhead = 1/L + 1/D

   where L and D are the number of columns and rows in the source block,
   respectively.

2.  Requirements Notation

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

Zanaty, et al.          Expires September 6, 2018               [Page 9]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

3.  Definitions and Notations

3.1.  Definitions

   This document uses a number of definitions from [RFC6363].

3.2.  Notations

   o  L: Number of columns of the source block.

   o  D: Number of rows of the source block.

   o  bitmask: Run-length encoding of packets protected by a FEC packet.
      If the bit i in the mask is set to 1, the source packet number N +
      i is protected by this FEC packet.  Here, N is the sequence number
      base, which is indicated in the FEC packet as well.

4.  Packet Formats

   This section defines the formats of the source and repair packets.

4.1.  Source Packets

   The source packets MUST contain the information that identifies the
   source block and the position within the source block occupied by the
   packet.  Since the source packets that are carried within an RTP
   stream already contain unique sequence numbers in their RTP headers
   [RFC3550], we can identify the source packets in a straightforward
   manner and there is no need to append additional field(s).  The
   primary advantage of not modifying the source packets in any way is
   that it provides backward compatibility for the receivers that do not
   support FEC at all.  In multicast scenarios, this backward
   compatibility becomes quite useful as it allows the non-FEC-capable
   and FEC-capable receivers to receive and interpret the same source
   packets sent in the same multicast session.

4.2.  Repair Packets

   The repair packets MUST contain information that identifies the
   source block they pertain to and the relationship between the
   contained repair packets and the original source block.  For this
   purpose, we use the RTP header of the repair packets as well as
   another header within the RTP payload, which we refer to as the FEC
   header, as shown in Figure 9.

   Note that all the source stream packets that are protected by a
   particular FEC packet need to be in the same RTP session.

Zanaty, et al.          Expires September 6, 2018              [Page 10]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

             +------------------------------+
             |          IP Header           |
             +------------------------------+
             |       Transport Header       |
             +------------------------------+
             |          RTP Header          |
             +------------------------------+ ---+
             |          FEC Header          |    |
             +------------------------------+    | RTP Payload
             |        Repair Payload        |    |
             +------------------------------+ ---+

                    Figure 9: Format of repair packets

   The RTP header is formatted according to [RFC3550] with some further
   clarifications listed below:

   o  Marker (M) Bit: This bit is not used for this payload type, and
      SHALL be set to 0.

   o  Payload Type: The (dynamic) payload type for the repair packets is
      determined through out-of-band means.  Note that this document
      registers new payload formats for the repair packets (Refer to
      Section 5 for details).  According to [RFC3550], an RTP receiver
      that cannot recognize a payload type must discard it.  This
      provides backward compatibility.  If a non-FEC-capable receiver
      receives a repair packet, it will not recognize the payload type,
      and hence, will discard the repair packet.

   o  Sequence Number (SN): The sequence number has the standard
      definition.  It MUST be one higher than the sequence number in the
      previously transmitted repair packet.  The initial value of the
      sequence number SHOULD be random (unpredictable, based on
      [RFC3550]).

   o  Timestamp (TS): The timestamp SHALL be set to a time corresponding
      to the repair packet's transmission time.  Note that the timestamp
      value has no use in the actual FEC protection process and is
      usually useful for jitter calculations.

   o  Synchronization Source (SSRC): The SSRC value for each repair
      stream SHALL be randomly assigned as suggested by [RFC3550].  This
      allows the sender to multiplex the source and repair RTP streams
      on the same port, or multiplex multiple repair streams on a single
      port.  The repair streams SHOULD use the RTCP CNAME field to
      associate themselves with the source stream.

Zanaty, et al.          Expires September 6, 2018              [Page 11]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

      In some networks, the RTP Source, which produces the source
      packets and the FEC Source, which generates the repair packets
      from the source packets may not be the same host.  In such
      scenarios, using the same CNAME for the source and repair RTP
      streams means that the RTP Source and the FEC Source MUST share
      the same CNAME (for this specific source-repair stream
      association).  A common CNAME may be produced based on an
      algorithm that is known both to the RTP and FEC Source [RFC7022].
      This usage is compliant with [RFC3550].

      Note that due to the randomness of the SSRC assignments, there is
      a possibility of SSRC collision.  In such cases, the collisions
      MUST be resolved as described in [RFC3550].

   The format of the FEC header is shown in Figure 10.

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |R|F| P|X|  CC   |M| PT recovery |         length recovery      |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                          TS recovery                          |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |           SN base_i           |k|          Mask [0-14]        |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |k|                   Mask [15-45] (optional)                   |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                                                               |
       +                     Mask [46-109] (optional)                  |
       |                                                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |     ... next SN base and Mask for CSRC_i in CSRC list ...     |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 10: Format of the FEC header

   The FEC header consists of the following fields:

   o  The R bit MUST be set to 1 to indicate a retransmission packet,
      and MUST be set to 0 for repair packets.

   o  The F field (1 bit) indicates the type of the mask.  Namely:

Zanaty, et al.          Expires September 6, 2018              [Page 12]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

    +---------------+-------------------------------------+
    |     F bit     | Use                                 |
    +---------------+-------------------------------------+
    |       0       | flexible mask                       |
    |       1       | packets indicated by offset M and N |
    +---------------+-------------------------------------+

                          Figure 11: F-bit values

   o  The P, X, CC, M and PT recovery fields are used to determine the
      corresponding fields of the recovered packets.

   o  The Length recovery (16 bits) field is used to determine the
      length of the recovered packets.

   o  The TS recovery (32 bits) field is used to determine the timestamp
      of the recovered packets.

   o  The CSRC_i (32 bits) field describes the SSRC of the packets
      protected by this particular FEC packet.  If a FEC packet contains
      protects multiple SSRCs (indicated by the CSRC Count > 1), there
      will be multiple blocks of data containing the SN base and Mask
      fields.

   o  The SN base_i (16 bits) field indicates the lowest sequence
      number, taking wrap around into account, of the source packets for
      a particular SSSRC (indicated in CSRC_i) protected by this repair
      packet.

   o  If the F-bit is set to 0, it represents that the source packets of
      all the SSRCs protected by this particular repair packet are
      indicated by using a flexible bitmask.  Mask is a run-length
      encoding of packets for a particular CSRC_i protected by the FEC
      packet.  Where a bit j set to 1 indicates that the source packet
      with sequence number (SN base_i + j + 1) is protected by this FEC
      packet.

   o  The k-bit in the bitmasks indicates if it is 15-, 46-, or a
      110-bitmask.  k=1 denotes that another mask follows, and k=0
      denotes that it is the last block of bit mask.

   o

Zanaty, et al.          Expires September 6, 2018              [Page 13]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |0|0| P|X|  CC  |M| PT recovery |         length recovery       |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                          TS recovery                          |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |           SN base_i           |k|          Mask [0-14]        |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |k|                   Mask [15-45] (optional)                   |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                                                               |
       +                     Mask [46-109] (optional)                  |
       |                                                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |   ... next SN base and Mask for CSRC_i in CSRC list ...       |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 12: Protocol format for F=0

   o  If the F-bit is set to 1, it represents that the source packets of
      all the SSRCs protected by this particular repair packet are
      indicated by using fixed offsets.

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |1|0| P|X|  CC  |M| PT recovery |         length recovery       |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                          TS recovery                          |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |           SN base_i           |  M (columns)  |    N (rows)   |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

                    Figure 13: Protocol format for F=1

      Consequently, the following conditions occur for M and N values:

Zanaty, et al.          Expires September 6, 2018              [Page 14]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   If M>0, N=0,  is Row FEC, and no column FEC will follow
               Hence, FEC = SN, SN+1, SN+2, ... , SN+(M-1), SN+M.

   If M>0, N=1,  is Row FEC, and column FEC will follow.
                 Hence, FEC = SN, SN+1, SN+2, ... , SN+(M-1), SN+M.
            and more to come

   If M>0, N>1,  indicates column FEC of every M packet
                    in a group of N packets starting at SN base.
                 Hence, FEC = SN+(Mx0), SN+(Mx1), ... , SN+(MxN).

             Figure 14: Interpreting the M and N field values

   By setting R to 1, F to 1, this FEC protects only one packet, i.e.,
   the FEC payload carries just the packet indicated by SN Base_i, which
   is effectively retransmitting the packet.

   Note that the parsing of this packet is different.  The sequence
   number (SN base_i) replaces the length recovery in the FEC packet.
   The CSRC Count (CC) which would be 1, M and N would be set to 0, and
   the reserved bits from the FEC header are removed.  By doing this, we
   save 64 bits.

        0                   1                   2                   3
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |1|1| P|X|  CC  |M| PT recovery |        sequence number        |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                           timestamp                           |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                              SSRC                             |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |                         Retransmission                        |
       :                            payload                            :
       |                                                               |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

               Figure 15: Protocol format for Retransmission

   The details on setting the fields in the FEC header are provided in
   Section 6.2.

   It should be noted that a mask-based approach (similar to the ones
   specified in [RFC2733] and [RFC5109]) may not be very efficient to
   indicate which source packets in the current source block are

Zanaty, et al.          Expires September 6, 2018              [Page 15]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   associated with a given repair packet.  In particular, for the
   applications that would like to use large source block sizes, the
   size of the mask that is required to describe the source-repair
   packet associations may be prohibitively large.  The 8-bit fields
   proposed in [SMPTE2022-1] indicate a systematized approach.  Instead
   the approach in this document uses the 8-bit fields to indicate
   packet offsets protected by the FEC packet.  The approach in
   [SMPTE2022-1] is inherently more efficient for regular patterns, it
   does not provide flexibility to represent other protection patterns
   (e.g., staircase).

5.  Payload Format Parameters

   This section provides the media subtype registration for the non-
   interleaved and interleaved parity FEC.  The parameters that are
   required to configure the FEC encoding and decoding operations are
   also defined in this section.  If no specific FEC code is specified
   in the subtype, then the FEC code defaults to the parity code defined
   in this specification.

5.1.  Media Type Registration - Parity Codes

   This registration is done using the template defined in [RFC6838] and
   following the guidance provided in [RFC3555].

   Note to the RFC Editor: In the following sections, please replace
   "XXXX" with the number of this document prior to publication as an
   RFC.

5.1.1.  Registration of audio/flexfec

   Type name: audio

   Subtype name: flexfec

   Required parameters:

   o  rate: The RTP timestamp (clock) rate.  The rate SHALL be larger
      than 1000 Hz to provide sufficient resolution to RTCP operations.
      However, it is RECOMMENDED to select the rate that matches the
      rate of the protected source RTP stream.

   o  repair-window: The time that spans the source packets and the
      corresponding repair packets.  The size of the repair window is
      specified in microseconds.

   Optional parameters:

Zanaty, et al.          Expires September 6, 2018              [Page 16]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   o  L: indicates the number of columns of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  L is a positive integer.

   o  D: indicates the number of rows of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  D is a positive integer.

   o  ToP: indicates the type of protection applied by the sender: 0 for
      1-D interleaved FEC protection, 1 for 1-D non-interleaved FEC
      protection, and 2 for 2-D parity FEC protection.  The ToP value of
      3 is reserved for future uses.

   Encoding considerations: This media type is framed (See Section 4.8
   in the template document [RFC6838]) and contains binary data.

   Security considerations: See Section 9 of [RFCXXXX].

   Interoperability considerations: None.

   Published specification: [RFCXXXX].

   Applications that use this media type: Multimedia applications that
   want to improve resiliency against packet loss by sending redundant
   data in addition to the source media.

   Fragment identifier considerations: None.

   Additional information: None.

   Person & email address to contact for further information: Varun
   Singh <varun@callstats.io> and IETF Audio/Video Transport Payloads
   Working Group.

   Intended usage: COMMON.

   Restriction on usage: This media type depends on RTP framing, and
   hence, is only defined for transport via RTP [RFC3550].

   Author: Varun Singh <varun@callstats.io>.

   Change controller: IETF Audio/Video Transport Working Group delegated
   from the IESG.

   Provisional registration? (standards tree only): Yes.

Zanaty, et al.          Expires September 6, 2018              [Page 17]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

5.1.2.  Registration of video/flexfec

   Type name: video

   Subtype name: flexfec

   Required parameters:

   o  rate: The RTP timestamp (clock) rate.  The rate SHALL be larger
      than 1000 Hz to provide sufficient resolution to RTCP operations.
      However, it is RECOMMENDED to select the rate that matches the
      rate of the protected source RTP stream.

   o  repair-window: The time that spans the source packets and the
      corresponding repair packets.  The size of the repair window is
      specified in microseconds.

   Optional parameters:

   o  L: indicates the number of columns of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  L is a positive integer.

   o  D: indicates the number of rows of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  D is a positive integer.

   o  ToP: indicates the type of protection applied by the sender: 0 for
      1-D interleaved FEC protection, 1 for 1-D non-interleaved FEC
      protection, and 2 for 2-D parity FEC protection.  The ToP value of
      3 is reserved for future uses.

   Encoding considerations: This media type is framed (See Section 4.8
   in the template document [RFC6838]) and contains binary data.

   Security considerations: See Section 9 of [RFCXXXX].

   Interoperability considerations: None.

   Published specification: [RFCXXXX].

   Applications that use this media type: Multimedia applications that
   want to improve resiliency against packet loss by sending redundant
   data in addition to the source media.

   Fragment identifier considerations: None.

   Additional information: None.

Zanaty, et al.          Expires September 6, 2018              [Page 18]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   Person & email address to contact for further information: Varun
   Singh <varun@callstats.io> and IETF Audio/Video Transport Payloads
   Working Group.

   Intended usage: COMMON.

   Restriction on usage: This media type depends on RTP framing, and
   hence, is only defined for transport via RTP [RFC3550].

   Author: Varun Singh <varun@callstats.io>.

   Change controller: IETF Audio/Video Transport Working Group delegated
   from the IESG.

   Provisional registration? (standards tree only): Yes.

5.1.3.  Registration of text/flexfec

   Type name: text

   Subtype name: flexfec

   Required parameters:

   o  rate: The RTP timestamp (clock) rate.  The rate SHALL be larger
      than 1000 Hz to provide sufficient resolution to RTCP operations.
      However, it is RECOMMENDED to select the rate that matches the
      rate of the protected source RTP stream.

   o  repair-window: The time that spans the source packets and the
      corresponding repair packets.  The size of the repair window is
      specified in microseconds.

   Optional parameters:

   o  L: indicates the number of columns of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  L is a positive integer.

   o  D: indicates the number of rows of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  D is a positive integer.

   o  ToP: indicates the type of protection applied by the sender: 0 for
      1-D interleaved FEC protection, 1 for 1-D non-interleaved FEC
      protection, and 2 for 2-D parity FEC protection.  The ToP value of
      3 is reserved for future uses.

Zanaty, et al.          Expires September 6, 2018              [Page 19]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   Encoding considerations: This media type is framed (See Section 4.8
   in the template document [RFC6838]) and contains binary data.

   Security considerations: See Section 9 of [RFCXXXX].

   Interoperability considerations: None.

   Published specification: [RFCXXXX].

   Applications that use this media type: Multimedia applications that
   want to improve resiliency against packet loss by sending redundant
   data in addition to the source media.

   Fragment identifier considerations: None.

   Additional information: None.

   Person & email address to contact for further information: Varun
   Singh <vvarun@callstats.io> and IETF Audio/Video Transport Payloads
   Working Group.

   Intended usage: COMMON.

   Restriction on usage: This media type depends on RTP framing, and
   hence, is only defined for transport via RTP [RFC3550].

   Author: Varun Singh <varun@callstats.io>.

   Change controller: IETF Audio/Video Transport Working Group delegated
   from the IESG.

   Provisional registration? (standards tree only): Yes.

5.1.4.  Registration of application/flexfec

   Type name: application

   Subtype name: flexfec

   Required parameters:

   o  rate: The RTP timestamp (clock) rate.  The rate SHALL be larger
      than 1000 Hz to provide sufficient resolution to RTCP operations.
      However, it is RECOMMENDED to select the rate that matches the
      rate of the protected source RTP stream.

Zanaty, et al.          Expires September 6, 2018              [Page 20]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   o  repair-window: The time that spans the source packets and the
      corresponding repair packets.  The size of the repair window is
      specified in microseconds.

   Optional parameters:

   o  L: indicates the number of columns of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  L is a positive integer.

   o  D: indicates the number of rows of the source block that are
      protected by this FEC block and it applies to all the source
      SSRCs.  D is a positive integer.

   o  ToP: indicates the type of protection applied by the sender: 0 for
      1-D interleaved FEC protection, 1 for 1-D non-interleaved FEC
      protection, and 2 for 2-D parity FEC protection.  The ToP value of
      3 is reserved for future uses.

   Encoding considerations: This media type is framed (See Section 4.8
   in the template document [RFC6838]) and contains binary data.

   Security considerations: See Section 9 of [RFCXXXX].

   Interoperability considerations: None.

   Published specification: [RFCXXXX].

   Applications that use this media type: Multimedia applications that
   want to improve resiliency against packet loss by sending redundant
   data in addition to the source media.

   Fragment identifier considerations: None.

   Additional information: None.

   Person & email address to contact for further information: Varun
   Singh <varun@callstats.io> and IETF Audio/Video Transport Payloads
   Working Group.

   Intended usage: COMMON.

   Restriction on usage: This media type depends on RTP framing, and
   hence, is only defined for transport via RTP [RFC3550].

   Author: Varun Singh <varun@callstats.io>.

Zanaty, et al.          Expires September 6, 2018              [Page 21]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   Change controller: IETF Audio/Video Transport Working Group delegated
   from the IESG.

   Provisional registration? (standards tree only): Yes.

5.2.  Mapping to SDP Parameters

   Applications that are using RTP transport commonly use Session
   Description Protocol (SDP) [RFC4566] to describe their RTP sessions.
   The information that is used to specify the media types in an RTP
   session has specific mappings to the fields in an SDP description.
   In this section, we provide these mappings for the media subtypes
   registered by this document.  Note that if an application does not
   use SDP to describe the RTP sessions, an appropriate mapping must be
   defined and used to specify the media types and their parameters for
   the control/description protocol employed by the application.

   The mapping of the media type specification for "non-interleaved-
   parityfec" and "interleaved-parityfec" and their parameters in SDP is
   as follows:

   o  The media type (e.g., "application") goes into the "m=" line as
      the media name.

   o  The media subtype goes into the "a=rtpmap" line as the encoding
      name.  The RTP clock rate parameter ("rate") also goes into the
      "a=rtpmap" line as the clock rate.

   o  The remaining required payload-format-specific parameters go into
      the "a=fmtp" line by copying them directly from the media type
      string as a semicolon-separated list of parameter=value pairs.

   SDP examples are provided in Section 7.

5.2.1.  Offer-Answer Model Considerations

   When offering 1-D interleaved parity FEC over RTP using SDP in an
   Offer/Answer model [RFC3264], the following considerations apply:

   o  Each combination of the L and D parameters produces a different
      FEC data and is not compatible with any other combination.  A
      sender application may desire to offer multiple offers with
      different sets of L and D values as long as the parameter values
      are valid.  The receiver SHOULD normally choose the offer that has
      a sufficient amount of interleaving.  If multiple such offers
      exist, the receiver may choose the offer that has the lowest
      overhead or the one that requires the smallest amount of
      buffering.  The selection depends on the application requirements.

Zanaty, et al.          Expires September 6, 2018              [Page 22]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   o  The value for the repair-window parameter depends on the L and D
      values and cannot be chosen arbitrarily.  More specifically, L and
      D values determine the lower limit for the repair-window size.
      The upper limit of the repair-window size does not depend on the L
      and D values.

   o  Although combinations with the same L and D values but with
      different repair-window sizes produce the same FEC data, such
      combinations are still considered different offers.  The size of
      the repair-window is related to the maximum delay between the
      transmission of a source packet and the associated repair packet.
      This directly impacts the buffering requirement on the receiver
      side and the receiver must consider this when choosing an offer.

   o  There are no optional format parameters defined for this payload.
      Any unknown option in the offer MUST be ignored and deleted from
      the answer.  If FEC is not desired by the receiver, it can be
      deleted from the answer.

5.2.2.  Declarative Considerations

   In declarative usage, like SDP in the Real-time Streaming Protocol
   (RTSP) [RFC2326] or the Session Announcement Protocol (SAP)
   [RFC2974], the following considerations apply:

   o  The payload format configuration parameters are all declarative
      and a participant MUST use the configuration that is provided for
      the session.

   o  More than one configuration may be provided (if desired) by
      declaring multiple RTP payload types.  In that case, the receivers
      should choose the repair stream that is best for them.

6.  Protection and Recovery Procedures - Parity Codes

   This section provides a complete specification of the 1-D and 2-D
   parity codes and their RTP payload formats.

6.1.  Overview

   The following sections specify the steps involved in generating the
   repair packets and reconstructing the missing source packets from the
   repair packets.

Zanaty, et al.          Expires September 6, 2018              [Page 23]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

6.2.  Repair Packet Construction

   The RTP header of a repair packet is formed based on the guidelines
   given in Section 4.2.

   The FEC header includes 12 octets (or upto 28 octets when the longer
   optional masks are used).  It is constructed by applying the XOR
   operation on the bit strings that are generated from the individual
   source packets protected by this particular repair packet.  The set
   of the source packets that are associated with a given repair packet
   can be computed by the formula given in Section 6.3.1.

   The bit string is formed for each source packet by concatenating the
   following fields together in the order specified:

   o  The first 64 bits of the RTP header (64 bits).

   o  Unsigned network-ordered 16-bit representation of the source
      packet length in bytes minus 12 (for the fixed RTP header), i.e.,
      the sum of the lengths of all the following if present: the CSRC
      list, extension header, RTP payload and RTP padding (16 bits).

   By applying the parity operation on the bit strings produced from the
   source packets, we generate the FEC bit string.  The FEC header is
   generated from the FEC bit string as follows:

   o  The first (most significant) 2 bits in the FEC bit string are
      skipped.  The MSK bits in the FEC header are set to the
      appropriate value, i.e., it depends on the chosen bitmask length.

   o  The next bit in the FEC bit string is written into the P recovery
      bit in the FEC header.

   o  The next bit in the FEC bit string is written into the X recovery
      bit in the FEC header.

   o  The next 4 bits of the FEC bit string are written into the CC
      recovery field in the FEC header.

   o  The next bit is written into the M recovery bit in the FEC header.

   o  The next 7 bits of the FEC bit string are written into the PT
      recovery field in the FEC header.

   o  The next 16 bits are skipped.

   o  The next 32 bits of the FEC bit string are written into the TS
      recovery field in the FEC header.

Zanaty, et al.          Expires September 6, 2018              [Page 24]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   o  The next 16 bits are written into the length recovery field in the
      FEC header.

   o  Depending on the chosen MSK value, the bit mask of appropriate
      length will be set to the appropriate values.

   As described in Section 4.2, the SN base field of the FEC header MUST
   be set to the lowest sequence number of the source packets protected
   by this repair packet.  When MSK represents a bitmask (MSK=00,01,10),
   the SN base field corresponds to the lowest sequence number indicated
   in the bitmask.  When MSK=11, the following considerations apply: 1)
   for the interleaved FEC repair packets, this corresponds to the
   lowest sequence number of the source packets that forms the column,
   2) for the non-interleaved FEC repair packets, the SN base field MUST
   be set to the lowest sequence number of the source packets that forms
   the row.

   The repair packet payload consists of the bits that are generated by
   applying the XOR operation on the payloads of the source RTP packets.
   If the payload lengths of the source packets are not equal, each
   shorter packet MUST be padded to the length of the longest packet by
   adding octet 0's at the end.

   Due to this possible padding and mandatory FEC header, a repair
   packet has a larger size than the source packets it protects.  This
   may cause problems if the resulting repair packet size exceeds the
   Maximum Transmission Unit (MTU) size of the path over which the
   repair stream is sent.

6.3.  Source Packet Reconstruction

   This section describes the recovery procedures that are required to
   reconstruct the missing source packets.  The recovery process has two
   steps.  In the first step, the FEC decoder determines which source
   and repair packets should be used in order to recover a missing
   packet.  In the second step, the decoder recovers the missing packet,
   which consists of an RTP header and RTP payload.

   In the following, we describe the RECOMMENDED algorithms for the
   first and second steps.  Based on the implementation, different
   algorithms MAY be adopted.  However, the end result MUST be identical
   to the one produced by the algorithms described below.

   Note that the same algorithms are used by the 1-D parity codes,
   regardless of whether the FEC protection is applied over a column or
   a row.  The 2-D parity codes, on the other hand, usually require
   multiple iterations of the procedures described here.  This iterative
   decoding algorithm is further explained in Section 6.3.4.

Zanaty, et al.          Expires September 6, 2018              [Page 25]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

6.3.1.  Associating the Source and Repair Packets

   We denote the set of the source packets associated with repair packet
   p* by set T(p*).  Note that in a source block whose size is L columns
   by D rows, set T includes D source packets plus one repair packet for
   the FEC protection applied over a column, and L source packets plus
   one repair packet for the FEC protection applied over a row.  Recall
   that 1-D interleaved and non-interleaved FEC protection can fully
   recover the missing information if there is only one source packet
   missing in set T.  If there are more than one source packets missing
   in set T, 1-D FEC protection will not work.

6.3.1.1.  Signaled in SDP

   The first step is associating the source and repair packets.  If the
   endpoint relies entirely on out-of-band signaling (MSK=11, and
   M=N=0), then this information may be inferred from the media type
   parameters specified in the SDP description.  Furthermore, the
   payload type field in the RTP header, assists the receiver
   distinguish an interleaved or non-interleaved FEC packet.

   Mathematically, for any received repair packet, p*, we can determine
   the sequence numbers of the source packets that are protected by this
   repair packet as follows:

                        p*_snb + i * X_1 (modulo 65536)

   where p*_snb denotes the value in the SN base field of p*'s FEC
   header, X_1 is set to L and 1 for the interleaved and non-interleaved
   FEC repair packets, respectively, and

                                 0 <= i < X_2

   where X_2 is set to D and L for the interleaved and non-interleaved
   FEC repair packets, respectively.

6.3.1.2.  Using bitmasks

   When using fixed size bitmasks (16-, 48-, 112-bits), the SN base
   field in the FEC header indicates the lowest sequence number of the
   source packets that forms the FEC packet.  Finally, the bits maked by
   "1" in the bitmask are offsets from the SN base and make up the rest
   of the packets protected by the FEC packet.  The bitmasks are able to
   represent arbitrary protection patterns, for example, 1-D
   interleaved, 1-D non-interleaved, 2-D, staircase.

Zanaty, et al.          Expires September 6, 2018              [Page 26]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

6.3.1.3.  Using M and N Offsets

   When value of M is non-zero, the 8-bit fields indicate the offset of
   packets protected by an interleaved (N>0) or non-interleaved (N=0)
   FEC packet.  Using a combination of interleaved and non-interleaved
   FEC repair packets can form 2-D protection patterns.

   Mathematically, for any received repair packet, p*, we can determine
   the sequence numbers of the source packets that are protected by this
   repair packet are as follows:

When N = 0:
  p*_snb, p*_snb+1,..., p*_snb+(M-1), p*_snb+M
When N > 0:
  p*_snb, p*_snb+(Mx1), p*_snb+(Mx2),..., p*_snb+(Mx(N-1)), p*_snb+(MxN)

6.3.2.  Recovering the RTP Header

   For a given set T, the procedure for the recovery of the RTP header
   of the missing packet, whose sequence number is denoted by SEQNUM, is
   as follows:

   1.   For each of the source packets that are successfully received in
        T, compute the 80-bit string by concatenating the first 64 bits
        of their RTP header and the unsigned network-ordered 16-bit
        representation of their length in bytes minus 12.

   2.   For the repair packet in T, compute the FEC bit string from the
        first 80 bits of the FEC header.

   3.   Calculate the recovered bit string as the XOR of the bit strings
        generated from all source packets in T and the FEC bit string
        generated from the repair packet in T.

   4.   Create a new packet with the standard 12-byte RTP header and no
        payload.

   5.   Set the version of the new packet to 2.  Skip the first 2 bits
        in the recovered bit string.

   6.   Set the Padding bit in the new packet to the next bit in the
        recovered bit string.

   7.   Set the Extension bit in the new packet to the next bit in the
        recovered bit string.

   8.   Set the CC field to the next 4 bits in the recovered bit string.

Zanaty, et al.          Expires September 6, 2018              [Page 27]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   9.   Set the Marker bit in the new packet to the next bit in the
        recovered bit string.

   10.  Set the Payload type in the new packet to the next 7 bits in the
        recovered bit string.

   11.  Set the SN field in the new packet to SEQNUM.  Skip the next 16
        bits in the recovered bit string.

   12.  Set the TS field in the new packet to the next 32 bits in the
        recovered bit string.

   13.  Take the next 16 bits of the recovered bit string and set the
        new variable Y to whatever unsigned integer this represents
        (assuming network order).  Convert Y to host order.  Y
        represents the length of the new packet in bytes minus 12 (for
        the fixed RTP header), i.e., the sum of the lengths of all the
        following if present: the CSRC list, header extension, RTP
        payload and RTP padding.

   14.  Set the SSRC of the new packet to the SSRC of the source RTP
        stream.

   This procedure recovers the header of an RTP packet up to (and
   including) the SSRC field.

6.3.3.  Recovering the RTP Payload

   Following the recovery of the RTP header, the procedure for the
   recovery of the RTP payload is as follows:

   1.  Append Y bytes to the new packet.

   2.  For each of the source packets that are successfully received in
       T, compute the bit string from the Y octets of data starting with
       the 13th octet of the packet.  If any of the bit strings
       generated from the source packets has a length shorter than Y,
       pad them to that length.  The padding of octet 0 MUST be added at
       the end of the bit string.  Note that the information of the
       first 8 octets are protected by the FEC header.

   3.  For the repair packet in T, compute the FEC bit string from the
       repair packet payload, i.e., the Y octets of data following the
       FEC header.  Note that the FEC header may be 12, 16, 32 octets
       depending on the length of the bitmask.

Zanaty, et al.          Expires September 6, 2018              [Page 28]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   4.  Calculate the recovered bit string as the XOR of the bit strings
       generated from all source packets in T and the FEC bit string
       generated from the repair packet in T.

   5.  Append the recovered bit string (Y octets) to the new packet
       generated in Section 6.3.2.

6.3.4.  Iterative Decoding Algorithm for the 2-D Parity FEC Protection

   In 2-D parity FEC protection, the sender generates both non-
   interleaved and interleaved FEC repair packets to combat with the
   mixed loss patterns (random and bursty).  At the receiver side, these
   FEC packets are used iteratively to overcome the shortcomings of the
   1-D non-interleaved/interleaved FEC protection and improve the
   chances of full error recovery.

   The iterative decoding algorithm runs as follows:

   1.  Set num_recovered_until_this_iteration to zero

   2.  Set num_recovered_so_far to zero

   3.  Recover as many source packets as possible by using the non-
       interleaved FEC repair packets as outlined in Section 6.3.2 and
       Section 6.3.3, and increase the value of num_recovered_so_far by
       the number of recovered source packets.

   4.  Recover as many source packets as possible by using the
       interleaved FEC repair packets as outlined in Section 6.3.2 and
       Section 6.3.3, and increase the value of num_recovered_so_far by
       the number of recovered source packets.

   5.  If num_recovered_so_far > num_recovered_until_this_iteration
       ---num_recovered_until_this_iteration = num_recovered_so_far
       ---Go to step 3
       Else
       ---Terminate

   The algorithm terminates either when all missing source packets are
   fully recovered or when there are still remaining missing source
   packets but the FEC repair packets are not able to recover any more
   source packets.  For the example scenarios when the 2-D parity FEC
   protection fails full recovery, refer to Section 1.1.4.  Upon
   termination, variable num_recovered_so_far has a value equal to the
   total number of recovered source packets.

   Example:

Zanaty, et al.          Expires September 6, 2018              [Page 29]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   Suppose that the receiver experienced the loss pattern sketched in
   Figure 16.

                                   +---+  +---+  +===+
                       X      X    | 3 |  | 4 |  |R_1|
                                   +---+  +---+  +===+

                     +---+  +---+  +---+  +---+  +===+
                     | 5 |  | 6 |  | 7 |  | 8 |  |R_2|
                     +---+  +---+  +---+  +---+  +===+

                     +---+                +---+  +===+
                     | 9 |    X      X    | 12|  |R_3|
                     +---+                +---+  +===+

                     +===+  +===+  +===+  +===+
                     |C_1|  |C_2|  |C_3|  |C_4|
                     +===+  +===+  +===+  +===+

   Figure 16: Example loss pattern for the iterative decoding algorithm

   The receiver executes the iterative decoding algorithm and recovers
   source packets #1 and #11 in the first iteration.  The resulting
   pattern is sketched in Figure 17.

                     +---+         +---+  +---+  +===+
                     | 1 |    X    | 3 |  | 4 |  |R_1|
                     +---+         +---+  +---+  +===+

                     +---+  +---+  +---+  +---+  +===+
                     | 5 |  | 6 |  | 7 |  | 8 |  |R_2|
                     +---+  +---+  +---+  +---+  +===+

                     +---+         +---+  +---+  +===+
                     | 9 |    X    | 11|  | 12|  |R_3|
                     +---+         +---+  +---+  +===+

                     +===+  +===+  +===+  +===+
                     |C_1|  |C_2|  |C_3|  |C_4|
                     +===+  +===+  +===+  +===+

        Figure 17: The resulting pattern after the first iteration

   Since the if condition holds true, the receiver runs a new iteration.
   In the second iteration, source packets #2 and #10 are recovered,
   resulting in a full recovery as sketched in Figure 18.

Zanaty, et al.          Expires September 6, 2018              [Page 30]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

                     +---+  +---+  +---+  +---+  +===+
                     | 1 |  | 2 |  | 3 |  | 4 |  |R_1|
                     +---+  +---+  +---+  +---+  +===+

                     +---+  +---+  +---+  +---+  +===+
                     | 5 |  | 6 |  | 7 |  | 8 |  |R_2|
                     +---+  +---+  +---+  +---+  +===+

                     +---+  +---+  +---+  +---+  +===+
                     | 9 |  | 10|  | 11|  | 12|  |R_3|
                     +---+  +---+  +---+  +---+  +===+

                     +===+  +===+  +===+  +===+
                     |C_1|  |C_2|  |C_3|  |C_4|
                     +===+  +===+  +===+  +===+

        Figure 18: The resulting pattern after the second iteration

7.  SDP Examples

   This section provides two SDP [RFC4566] examples.  The examples use
   the FEC grouping semantics defined in [RFC5956].

7.1.  Example SDP for Flexible FEC Protection with in-band SSRC mapping

   In this example, we have one source video stream and one FEC repair
   stream.  The source and repair streams are multiplexed on different
   SSRCs.  The repair window is set to 200 ms.

        v=0
        o=mo 1122334455 1122334466 IN IP4 fec.example.com
        s=FlexFEC minimal SDP signalling Example
        t=0 0
        m=video 30000 RTP/AVP 96 98
        c=IN IP4 143.163.151.157
        a=rtpmap:96 VP8/90000
        a=rtpmap:98 flexfec/90000
        a=fmtp:98; repair-window=200ms

7.2.  Example SDP for Flex FEC Protection with explicit signalling in
      the SDP

   In this example, we have one source video stream (ssrc:1234) and one
   FEC repair streams (ssrc:2345).  We form one FEC group with the
   "a=ssrc-group:FEC-FR 1234 2345" line.  The source and repair streams

Zanaty, et al.          Expires September 6, 2018              [Page 31]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   are multiplexed on different SSRCs.  The repair window is set to 200
   ms.

        v=0
        o=ali 1122334455 1122334466 IN IP4 fec.example.com
        s=2-D Parity FEC with no in band signalling Example
        t=0 0
        m=video 30000 RTP/AVP 100 110
        c=IN IP4 233.252.0.1/127
        a=rtpmap:100 MP2T/90000
        a=rtpmap:110 flexfec/90000
        a=fmtp:110 L:5; D:10; ToP:2; repair-window:200000
        a=ssrc:1234
        a=ssrc:2345
        a=ssrc-group:FEC-FR 1234 2345

8.  Congestion Control Considerations

   FEC is an effective approach to provide applications resiliency
   against packet losses.  However, in networks where the congestion is
   a major contributor to the packet loss, the potential impacts of
   using FEC SHOULD be considered carefully before injecting the repair
   streams into the network.  In particular, in bandwidth-limited
   networks, FEC repair streams may consume most or all of the available
   bandwidth and consequently may congest the network.  In such cases,
   the applications MUST NOT arbitrarily increase the amount of FEC
   protection since doing so may lead to a congestion collapse.  If
   desired, stronger FEC protection MAY be applied only after the source
   rate has been reduced.

   In a network-friendly implementation, an application SHOULD NOT send/
   receive FEC repair streams if it knows that sending/receiving those
   FEC repair streams would not help at all in recovering the missing
   packets.  However, it MAY still continue to use FEC if considered for
   bandwidth estimation instead of speculatively probe for additional
   capacity [Holmer13][Nagy14].  It is RECOMMENDED that the amount of
   FEC protection is adjusted dynamically based on the packet loss rate
   observed by the applications.

   In multicast scenarios, it may be difficult to optimize the FEC
   protection per receiver.  If there is a large variation among the
   levels of FEC protection needed by different receivers, it is
   RECOMMENDED that the sender offers multiple repair streams with
   different levels of FEC protection and the receivers join the
   corresponding multicast sessions to receive the repair stream(s) that
   is best for them.

Zanaty, et al.          Expires September 6, 2018              [Page 32]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

9.  Security Considerations

   RTP packets using the payload format defined in this specification
   are subject to the security considerations discussed in the RTP
   specification [RFC3550] and in any applicable RTP profile.  The main
   security considerations for the RTP packet carrying the RTP payload
   format defined within this memo are confidentiality, integrity and
   source authenticity.  Confidentiality is achieved by encrypting the
   RTP payload.  Integrity of the RTP packets is achieved through a
   suitable cryptographic integrity protection mechanism.  Such a
   cryptographic system may also allow the authentication of the source
   of the payload.  A suitable security mechanism for this RTP payload
   format should provide confidentiality, integrity protection, and at
   least source authentication capable of determining if an RTP packet
   is from a member of the RTP session.

   Note that the appropriate mechanism to provide security to RTP and
   payloads following this memo may vary.  It is dependent on the
   application, transport and signaling protocol employed.  Therefore, a
   single mechanism is not sufficient, although if suitable, using the
   Secure Real-time Transport Protocol (SRTP) [RFC3711] is recommended.
   Other mechanisms that may be used are IPsec [RFC4301] and Transport
   Layer Security (TLS) [RFC5246] (RTP over TCP); other alternatives may
   exist.

10.  IANA Considerations

   New media subtypes are subject to IANA registration.  For the
   registration of the payload formats and their parameters introduced
   in this document, refer to Section 5.

11.  Acknowledgments

   Some parts of this document are borrowed from [RFC5109].  Thus, the
   author would like to thank the editor of [RFC5109] and those who
   contributed to [RFC5109].

   Thanks to Bernard Aboba , Rasmus Brandt , Roni Even , Stefan Holmer ,
   Jonathan Lennox , and Magnus Westerlund for providing valuable
   feedback on earlier versions of this draft.

12.  Change Log

   Note to the RFC-Editor: please remove this section prior to
   publication as an RFC.

Zanaty, et al.          Expires September 6, 2018              [Page 33]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

12.1.  draft-ietf-payload-flexible-fec-scheme-05

   FEC packet format changed as per discussions in IETF97, Seoul.

12.2.  draft-ietf-payload-flexible-fec-scheme-03

   FEC packet format changed as per discussions in IETF96, Berlin.

   Removed section on non-parity codes and flexfec-raptor.

12.3.  draft-ietf-payload-flexible-fec-scheme-02

   FEC packet format changed as per discussions in IETF94, Tokyo.

   Added section on non-parity codes.

   Registration of application/flexfec-raptor.

12.4.  draft-ietf-payload-flexible-fec-scheme-01

   FEC packet format changed as per discussions in IETF93, Prague.

   Replaced non-interleaved-parityfec and interleaved-parity-fec with
   flexfec.

   SDP simplified for the case when association to RTP is made in the
   FEC header and not in the SDP.

12.5.  draft-ietf-payload-flexible-fec-scheme-00

   Initial WG version, based on draft-singh-payload-1d2d-parity-scheme-
   00.

12.6.  draft-singh-payload-1d2d-parity-scheme-00

   This is the initial version, which is based on draft-ietf-fecframe-
   1d2d-parity-scheme-00.  The following are the major changes compared
   to that document:

   o  Updated packet format with 16-, 48-, 112- bitmask.

   o  Updated the sections on: repair packet construction, source packet
      construction.

   o  Updated the media type registration and aligned to RFC6838.

Zanaty, et al.          Expires September 6, 2018              [Page 34]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

12.7.  draft-ietf-fecframe-1d2d-parity-scheme-00

   o  Some details were added regarding the use of CNAME field.

   o  Offer-Answer and Declarative Considerations sections have been
      completed.

   o  Security Considerations section has been completed.

   o  The timestamp field definition has changed.

13.  References

13.1.  Normative References

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119,
              DOI 10.17487/RFC2119, March 1997,
              <https://www.rfc-editor.org/info/rfc2119>.

   [RFC3264]  Rosenberg, J. and H. Schulzrinne, "An Offer/Answer Model
              with Session Description Protocol (SDP)", RFC 3264,
              DOI 10.17487/RFC3264, June 2002,
              <https://www.rfc-editor.org/info/rfc3264>.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
              July 2003, <https://www.rfc-editor.org/info/rfc3550>.

   [RFC3555]  Casner, S. and P. Hoschka, "MIME Type Registration of RTP
              Payload Formats", RFC 3555, DOI 10.17487/RFC3555, July
              2003, <https://www.rfc-editor.org/info/rfc3555>.

   [RFC4566]  Handley, M., Jacobson, V., and C. Perkins, "SDP: Session
              Description Protocol", RFC 4566, DOI 10.17487/RFC4566,
              July 2006, <https://www.rfc-editor.org/info/rfc4566>.

   [RFC5956]  Begen, A., "Forward Error Correction Grouping Semantics in
              the Session Description Protocol", RFC 5956,
              DOI 10.17487/RFC5956, September 2010,
              <https://www.rfc-editor.org/info/rfc5956>.

   [RFC6363]  Watson, M., Begen, A., and V. Roca, "Forward Error
              Correction (FEC) Framework", RFC 6363,
              DOI 10.17487/RFC6363, October 2011,
              <https://www.rfc-editor.org/info/rfc6363>.

Zanaty, et al.          Expires September 6, 2018              [Page 35]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   [RFC6709]  Carpenter, B., Aboba, B., Ed., and S. Cheshire, "Design
              Considerations for Protocol Extensions", RFC 6709,
              DOI 10.17487/RFC6709, September 2012,
              <https://www.rfc-editor.org/info/rfc6709>.

   [RFC6838]  Freed, N., Klensin, J., and T. Hansen, "Media Type
              Specifications and Registration Procedures", BCP 13,
              RFC 6838, DOI 10.17487/RFC6838, January 2013,
              <https://www.rfc-editor.org/info/rfc6838>.

   [RFC7022]  Begen, A., Perkins, C., Wing, D., and E. Rescorla,
              "Guidelines for Choosing RTP Control Protocol (RTCP)
              Canonical Names (CNAMEs)", RFC 7022, DOI 10.17487/RFC7022,
              September 2013, <https://www.rfc-editor.org/info/rfc7022>.

13.2.  Informative References

   [Holmer13]
              Holmer, S., Shemer, M., and M. Paniconi, "Handling Packet
              Loss in WebRTC", Proc. of IEEE International Conference on
              Image Processing (ICIP 2013) , 9 2013.

   [Nagy14]   Nagy, M., Singh, V., Ott, J., and L. Eggert, "Congestion
              Control using FEC for Conversational Multimedia
              Communication", Proc. of 5th ACM Internation Conference on
              Multimedia Systems (MMSys 2014) , 3 2014.

   [RFC2326]  Schulzrinne, H., Rao, A., and R. Lanphier, "Real Time
              Streaming Protocol (RTSP)", RFC 2326,
              DOI 10.17487/RFC2326, April 1998,
              <https://www.rfc-editor.org/info/rfc2326>.

   [RFC2733]  Rosenberg, J. and H. Schulzrinne, "An RTP Payload Format
              for Generic Forward Error Correction", RFC 2733,
              DOI 10.17487/RFC2733, December 1999,
              <https://www.rfc-editor.org/info/rfc2733>.

   [RFC2974]  Handley, M., Perkins, C., and E. Whelan, "Session
              Announcement Protocol", RFC 2974, DOI 10.17487/RFC2974,
              October 2000, <https://www.rfc-editor.org/info/rfc2974>.

   [RFC3711]  Baugher, M., McGrew, D., Naslund, M., Carrara, E., and K.
              Norrman, "The Secure Real-time Transport Protocol (SRTP)",
              RFC 3711, DOI 10.17487/RFC3711, March 2004,
              <https://www.rfc-editor.org/info/rfc3711>.

Zanaty, et al.          Expires September 6, 2018              [Page 36]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   [RFC4301]  Kent, S. and K. Seo, "Security Architecture for the
              Internet Protocol", RFC 4301, DOI 10.17487/RFC4301,
              December 2005, <https://www.rfc-editor.org/info/rfc4301>.

   [RFC4585]  Ott, J., Wenger, S., Sato, N., Burmeister, C., and J. Rey,
              "Extended RTP Profile for Real-time Transport Control
              Protocol (RTCP)-Based Feedback (RTP/AVPF)", RFC 4585,
              DOI 10.17487/RFC4585, July 2006,
              <https://www.rfc-editor.org/info/rfc4585>.

   [RFC5109]  Li, A., Ed., "RTP Payload Format for Generic Forward Error
              Correction", RFC 5109, DOI 10.17487/RFC5109, December
              2007, <https://www.rfc-editor.org/info/rfc5109>.

   [RFC5246]  Dierks, T. and E. Rescorla, "The Transport Layer Security
              (TLS) Protocol Version 1.2", RFC 5246,
              DOI 10.17487/RFC5246, August 2008,
              <https://www.rfc-editor.org/info/rfc5246>.

   [RFC7656]  Lennox, J., Gross, K., Nandakumar, S., Salgueiro, G., and
              B. Burman, Ed., "A Taxonomy of Semantics and Mechanisms
              for Real-Time Transport Protocol (RTP) Sources", RFC 7656,
              DOI 10.17487/RFC7656, November 2015,
              <https://www.rfc-editor.org/info/rfc7656>.

   [SMPTE2022-1]
              SMPTE 2022-1-2007, "Forward Error Correction for Real-Time
              Video/Audio Transport over IP Networks", 2007.

Authors' Addresses

   Mo Zanaty
   Cisco
   Raleigh, NC
   USA

   Email: mzanaty@cisco.com

   Varun Singh
   CALLSTATS I/O Oy
   Runeberginkatu 4c A 4
   Helsinki  00100
   Finland

   Email: varun.singh@iki.fi
   URI:   http://www.callstats.io/

Zanaty, et al.          Expires September 6, 2018              [Page 37]
Internet-Draft      RTP Payload Format for Parity FEC         March 2018

   Ali Begen
   Networked Media
   Konya
   Turkey

   Email: ali.begen@networked.media

   Giridhar Mandyam
   Qualcomm Innovation Center
   5775 Morehouse Drive
   San Diego, CA  92121
   USA

   Phone: +1 858 651 7200
   Email: mandyam@qti.qualcomm.com

Zanaty, et al.          Expires September 6, 2018              [Page 38]