Skip to main content

Deterministic Networking Architecture
draft-ietf-detnet-architecture-04

The information below is for an old version of the document.
Document Type
This is an older version of an Internet-Draft that was ultimately published as RFC 8655.
Authors Norman Finn , Pascal Thubert , Balazs Varga , János Farkas
Last updated 2017-10-30
Replaces draft-finn-detnet-architecture
RFC stream Internet Engineering Task Force (IETF)
Formats
Reviews
Additional resources Mailing list discussion
Stream WG state WG Document
Document shepherd (None)
IESG IESG state Became RFC 8655 (Proposed Standard)
Consensus boilerplate Unknown
Telechat date (None)
Responsible AD (None)
Send notices to (None)
draft-ietf-detnet-architecture-04
DetNet                                                           N. Finn
Internet-Draft                               Huawei Technologies Co. Ltd
Intended status: Standards Track                              P. Thubert
Expires: May 3, 2018                                               Cisco
                                                                B. Varga
                                                               J. Farkas
                                                                Ericsson
                                                        October 30, 2017

                 Deterministic Networking Architecture
                   draft-ietf-detnet-architecture-04

Abstract

   Deterministic Networking (DetNet) provides a capability to carry
   specified unicast or multicast data flows for real-time applications
   with extremely low data loss rates and bounded latency.  Techniques
   used include: 1) reserving data plane resources for individual (or
   aggregated) DetNet flows in some or all of the intermediate nodes
   (e.g. bridges or routers) along the path of the flow; 2) providing
   explicit routes for DetNet flows that do not rapidly change with the
   network topology; and 3) distributing data from DetNet flow packets
   over time and/or space to ensure delivery of each packet's data' in
   spite of the loss of a path.  The capabilities can be managed by
   configuration, or by manual or automatic network management.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on May 3, 2018.

Finn, et al.               Expires May 3, 2018                  [Page 1]
Internet-Draft    Deterministic Networking Architecture     October 2017

Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents
   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Terminology . . . . . . . . . . . . . . . . . . . . . . . . .   4
     2.1.  Terms used in this document . . . . . . . . . . . . . . .   4
     2.2.  IEEE 802 TSN to DetNet dictionary . . . . . . . . . . . .   6
   3.  Providing the DetNet Quality of Service . . . . . . . . . . .   7
     3.1.  Primary goals defining the DetNet QoS . . . . . . . . . .   7
     3.2.  Mechanisms to achieve DetNet Qos  . . . . . . . . . . . .   9
       3.2.1.  Congestion protection . . . . . . . . . . . . . . . .   9
       3.2.2.  Explicit routes . . . . . . . . . . . . . . . . . . .   9
       3.2.3.  Jitter Reduction  . . . . . . . . . . . . . . . . . .  10
       3.2.4.  Packet Replication and Elimination  . . . . . . . . .  11
     3.3.  Secondary goals for DetNet  . . . . . . . . . . . . . . .  12
       3.3.1.  Coexistence with normal traffic . . . . . . . . . . .  12
       3.3.2.  Fault Mitigation  . . . . . . . . . . . . . . . . . .  13
   4.  DetNet Architecture . . . . . . . . . . . . . . . . . . . . .  14
     4.1.  DetNet stack model  . . . . . . . . . . . . . . . . . . .  14
       4.1.1.  Representative Protocol Stack Model . . . . . . . . .  14
       4.1.2.  DetNet Data Plane Overview  . . . . . . . . . . . . .  16
       4.1.3.  Network reference model . . . . . . . . . . . . . . .  18
     4.2.  DetNet systems  . . . . . . . . . . . . . . . . . . . . .  19
       4.2.1.  End system  . . . . . . . . . . . . . . . . . . . . .  19
       4.2.2.  DetNet edge, relay, and transit nodes . . . . . . . .  20
     4.3.  DetNet flows  . . . . . . . . . . . . . . . . . . . . . .  21
       4.3.1.  DetNet flow types . . . . . . . . . . . . . . . . . .  21
       4.3.2.  Source guarantees . . . . . . . . . . . . . . . . . .  21
       4.3.3.  Incomplete Networks . . . . . . . . . . . . . . . . .  23
     4.4.  Traffic Engineering for DetNet  . . . . . . . . . . . . .  23
       4.4.1.  The Application Plane . . . . . . . . . . . . . . . .  23
       4.4.2.  The Controller Plane  . . . . . . . . . . . . . . . .  24
       4.4.3.  The Network Plane . . . . . . . . . . . . . . . . . .  24
     4.5.  Queuing, Shaping, Scheduling, and Preemption  . . . . . .  25

Finn, et al.               Expires May 3, 2018                  [Page 2]
Internet-Draft    Deterministic Networking Architecture     October 2017

     4.6.  Service instance  . . . . . . . . . . . . . . . . . . . .  26
     4.7.  Flow identification at technology borders . . . . . . . .  27
       4.7.1.  Exporting flow identification . . . . . . . . . . . .  27
       4.7.2.  Flow attribute mapping between layers . . . . . . . .  29
       4.7.3.  Flow-ID mapping examples  . . . . . . . . . . . . . .  30
     4.8.  Advertising resources, capabilities and adjacencies . . .  32
     4.9.  Provisioning model  . . . . . . . . . . . . . . . . . . .  32
       4.9.1.  Centralized Path Computation and Installation . . . .  32
       4.9.2.  Distributed Path Setup  . . . . . . . . . . . . . . .  32
     4.10. Scaling to larger networks  . . . . . . . . . . . . . . .  33
     4.11. Connected islands vs. networks  . . . . . . . . . . . . .  33
     4.12. Compatibility with Layer-2  . . . . . . . . . . . . . . .  33
   5.  Security Considerations . . . . . . . . . . . . . . . . . . .  34
   6.  Privacy Considerations  . . . . . . . . . . . . . . . . . . .  34
   7.  IANA Considerations . . . . . . . . . . . . . . . . . . . . .  35
   8.  Acknowledgements  . . . . . . . . . . . . . . . . . . . . . .  35
   9.  Access to IEEE 802.1 documents  . . . . . . . . . . . . . . .  35
   10. Informative References  . . . . . . . . . . . . . . . . . . .  35
   Authors' Addresses  . . . . . . . . . . . . . . . . . . . . . . .  40

1.  Introduction

   Deterministic Networking (DetNet) is a service that can be offered by
   a network to DetNet flows.  DetNet provides these flows extremely low
   packet loss rates and assured maximum end-to-end delivery latency.
   This is accomplished by dedicating network resources such as link
   bandwidth and buffer space to DetNet flows and/or classes of DetNet
   flows, and by replicating packets along multiple paths.  Unused
   reserved resources are available to non-DetNet packets.

   The Deterministic Networking Problem Statement
   [I-D.ietf-detnet-problem-statement] introduces Deterministic
   Networking, and Deterministic Networking Use Cases
   [I-D.ietf-detnet-use-cases] summarizes the need for it.  See
   [I-D.dt-detnet-dp-alt] for a discussion of specific techniques that
   can be used to identify DetNet Flows and assign them to specific
   paths through a network.

   A goal of DetNet is a converged network in all respects.  That is,
   the presence of DetNet flows does not preclude non-DetNet flows, and
   the benefits offered DetNet flows should not, except in extreme
   cases, prevent existing QoS mechanisms from operating in a normal
   fashion, subject to the bandwidth required for the DetNet flows.  A
   single source-destination pair can trade both DetNet and non-DetNet
   flows.  End systems and applications need not instantiate special
   interfaces for DetNet flows.  Networks are not restricted to certain
   topologies; connectivity is not restricted.  Any application that
   generates a data flow that can be usefully characterized as having a

Finn, et al.               Expires May 3, 2018                  [Page 3]
Internet-Draft    Deterministic Networking Architecture     October 2017

   maximum bandwidth should be able to take advantage of DetNet, as long
   as the necessary resources can be reserved.  Reservations can be made
   by the application itself, via network management, by an applications
   controller, or by other means.

   Many applications of interest to Deterministic Networking require the
   ability to synchronize the clocks in end systems to a sub-microsecond
   accuracy.  Some of the queue control techniques defined in
   Section 4.5 also require time synchronization among relay and transit
   nodes.  The means used to achieve time synchronization are not
   addressed in this document.  DetNet should accommodate various
   synchronization techniques and profiles that are defined elsewhere to
   solve exchange time in different market segments.

   Wired and wireless media differ greatly in a number of ways,
   including connectivity possibilities and the reliability of packet
   transmission.  While some of the techniques described in this
   document may be applicable to wireless media, the DetNet architecture
   assumes the use of links with characteristics typical of wired, and
   not wireless, media.

2.  Terminology

2.1.  Terms used in this document

   The following special terms are used in this document in order to
   avoid the assumption that a given element in the architecture does or
   does not have Internet Protocol stack, functions as a router, bridge,
   firewall, or otherwise plays a particular role at Layer-2 or higher.

   App-flow
           The native format of a DetNet flow.

   destination
           An end system capable of receiving a DetNet flow.

   DetNet domain
           The portion of a network that is DetNet aware.  It includes
           end systems and other DetNet nodes.

   DetNet flow
           A DetNet flow is a sequence of packets to which the DetNet
           service is to be provided.

   DetNet compound flow and DetNet member flow
           A DetNet compound flow is a DetNet flow that has been
           separated into multiple duplicate DetNet member flows, which
           are eventually merged back into a single DetNet compound

Finn, et al.               Expires May 3, 2018                  [Page 4]
Internet-Draft    Deterministic Networking Architecture     October 2017

           flow, at the DetNet transport layer.  "Compound" and "member"
           are strictly relative to each other, not absolutes; a DetNet
           compound flow comprising multiple DetNet member flows can, in
           turn, be a member of a higher-order compound.

   DetNet intermediate node
           A DetNet relay node or transit node.

   DetNet edge node
           An instance of a DetNet relay node that includes either a
           DetNet service layer proxy function for DetNet service
           protection (e.g. the addition or removal of packet sequencing
           information) for one or more end systems, or starts or
           terminates congestion protection at the DetNet transport
           layer, analogous to a Label Edge Router (LER).

   DetNet-UNI
           User-to-Network Interface with DetNet specific
           functionalities.  It is a packet-based reference point and
           may provide multiple functions like encapsulation, status,
           synchronization, etc.

   end system
           Commonly called a "host" or "node" in IETF documents, and an
           "end station" is IEEE 802 documents.  End systems of interest
           to this document are either sources or destinations of DetNet
           flows.  And end system may or may not be DetNet transport
           layer aware or DetNet service layer aware.

   link
           A connection between two DetNet nodes.  It may be composed of
           a physical link or a sub-network technology that can provide
           appropriate traffic delivery for DetNet flows.

   DetNet node
           A DetNet aware end system, transit node, or relay node.
           "DetNet" may be omitted in some text.

   Detnet relay node
           A DetNet node including a service layer function that
           interconnects different DetNet transport layer paths to
           provide service protection.  A DetNet relay node can be a
           bridge, a router, a firewall, or any other system that
           participates in the DetNet service layer.  It typically
           incorporates DetNet transport layer functions as well, in
           which case it is collocated with a transit node.

   reservation

Finn, et al.               Expires May 3, 2018                  [Page 5]
Internet-Draft    Deterministic Networking Architecture     October 2017

           A trail of configuration between source to destination(s)
           through transit nodes and subnets associated with a DetNet
           flow, to provide congestion protection.

   DetNet service layer
           The layer at which service protection is provided, packet
           sequencing, replication, and elimination (Section 3.2.4) or
           packet encoding.

   source
           An end system capable of sourcing a DetNet flow.

   DetNet transit node
           A node operating at the DetNet transport layer, that utilizes
           link layer and/or network layer switching across multiple
           links and/or sub-networks to provide paths for DetNet service
           layer functions.  Optionally provides congestion protection
           over those paths.  An MPLS LSR is an example of a DetNet
           transit node.

   DetNet transport layer
           The layer that optionally provides congestion protection for
           DetNet flows over paths provided by the underlying network.

   TSN
           Time-Sensitive Networking, TSN is a Task Group of the IEEE
           802.1 Working Group.

2.2.  IEEE 802 TSN to DetNet dictionary

   This section also serves as a dictionary for translating from the
   terms used by the IEEE 802 Time-Sensitive Networking (TSN) Task Group
   to those of the DetNet WG.

   Listener
           The IEEE 802 term for a destination of a DetNet flow.

   relay system
           The IEEE 802 term for a DetNet intermediate node.

   Stream
           The IEEE 802 term for a DetNet flow.

   Talker
           The IEEE 802 term for the source of a DetNet flow.

Finn, et al.               Expires May 3, 2018                  [Page 6]
Internet-Draft    Deterministic Networking Architecture     October 2017

3.  Providing the DetNet Quality of Service

3.1.  Primary goals defining the DetNet QoS

   The DetNet Quality of Service can be expressed in terms of:

   o  Minimum and maximum end-to-end latency from source to destination;
      timely delivery and jitter avoidance derive from these constraints

   o  Probability of loss of a packet, under various assumptions as to
      the operational states of the nodes and links.  A derived property
      is whether it is acceptable to deliver a duplicate packet, which
      is an inherent risk in highly reliable and/or broadcast
      transmissions

   It is a distinction of DetNet that it is concerned solely with worst-
   case values for the end-to-end latency.  Average, mean, or typical
   values are of no interest, because they do not affect the ability of
   a real-time system to perform its tasks.  In general, a trivial
   priority-based queuing scheme will give better average latency to a
   data flow than DetNet, but of course, the worst-case latency can be
   essentially unbounded.

   Three techniques are used by DetNet to provide these qualities of
   service:

   o  Congestion protection (Section 3.2.1).

   o  Explicit routes (Section 3.2.2).

   o  Service protection (Section 3.2.4).

   Congestion protection operates by reserving resources along the path
   of a DetNet Flow, e.g. buffer space or link bandwidth.  Congestion
   protection greatly reduces, or even eliminates entirely, packet loss
   due to output packet congestion within the network, but it can only
   be supplied to a DetNet flow that is limited at the source to a
   maximum packet size and transmission rate.

   Congestion protection addresses both of the DetNet QoS requirements
   (latency and packet loss).  Given that DetNet nodes have a finite
   amount of buffer space, congestion protection necessarily results in
   a maximum end-to-end latency.  It also addresses the largest
   contribution to packet loss, which is buffer congestion.

   After congestion, the most important contributions to packet loss are
   typically from random media errors and equipment failures.  Service
   protection is the name for the mechanisms used by DetNet to address

Finn, et al.               Expires May 3, 2018                  [Page 7]
Internet-Draft    Deterministic Networking Architecture     October 2017

   these losses.  The mechanisms employed are constrained by the
   requirement to meet the users' latency requirements.  Packet
   replication and elimination (Section 3.2.4) is described in this
   document to provide service protection; others may be found.  This
   mechanism distributes the contents of DetNet flows over multiple
   paths in time and/or space, so that the loss of some of the paths
   does need not cause the loss of any packets.  The paths are typically
   (but not necessarily) explicit routes, so that they cannot suffer
   temporary interruptions caused by the reconvergence of routing or
   bridging protocols.

   These three techniques can be applied independently, giving eight
   possible combinations, including none (no DetNet), although some
   combinations are of wider utility than others.  This separation keeps
   the protocol stack coherent and maximizes interoperability with
   existing and developing standards in this (IETF) and other Standards
   Development Organizations.  Some examples of typical expected
   combinations:

   o  Explicit routes plus service protection are exactly the techniques
      employed by [HSR-PRP].  Explicit routes are achieved by limiting
      the physical topology of the network, and the sequentialization,
      replication, and duplicate elimination are facilitated by packet
      tags added at the front or the end of Ethernet frames.

   o  Congestion protection alone is is offered by IEEE 802.1 Audio
      Video bridging [IEEE802.1BA-2011].  As long as the network suffers
      no failures, zero congestion loss can be achieved through the use
      of a reservation protocol (MSRP), shapers in every bridge, and a
      bit of network calculus.

   o  Using all three together gives maximum protection.

   There are, of course, simpler methods available (and employed, today)
   to achieve levels of latency and packet loss that are satisfactory
   for many applications.  Prioritization and over-provisioning is one
   such technique.  However, these methods generally work best in the
   absence of any significant amount of non-critical traffic in the
   network (if, indeed, such traffic is supported at all), or work only
   if the critical traffic constitutes only a small portion of the
   network's theoretical capacity, or work only if all systems are
   functioning properly, or in the absence of actions by end systems
   that disrupt the network's operations.

   There are any number of methods in use, defined, or in progress for
   accomplishing each of the above techniques.  It is expected that this
   DetNet Architecture will assist various vendors, users, and/or
   "vertical" Standards Development Organizations (dedicated to a single

Finn, et al.               Expires May 3, 2018                  [Page 8]
Internet-Draft    Deterministic Networking Architecture     October 2017

   industry) to make selections among the available means of
   implementing DetNet networks.

3.2.  Mechanisms to achieve DetNet Qos

3.2.1.  Congestion protection

   The primary means by which DetNet achieves its QoS assurances is to
   reduce, or even completely eliminate, congestion at an output port as
   a cause of packet loss.  Given that a DetNet flow cannot be
   throttled, this can be achieved only by the provision of sufficient
   buffer storage at each hop through the network to ensure that no
   packets are dropped due to a lack of buffer storage.

   Ensuring adequate buffering requires, in turn, that the source, and
   every intermediate node along the path to the destination (or nearly
   every node -- see Section 4.3.3) be careful to regulate its output to
   not exceed the data rate for any DetNet flow, except for brief
   periods when making up for interfering traffic.  Any packet sent
   ahead of its time potentially adds to the number of buffers required
   by the next hop, and may thus exceed the resources allocated for a
   particular DetNet flow.

   The low-level mechanisms described in Section 4.5 provide the
   necessary regulation of transmissions by an end system or
   intermediate node to provide congestion protection.  The reservation
   of the bandwidth and buffers for a DetNet flow requires the
   provisioning described in Section 4.9.  A DetNet node may have other
   resources requiring allocation and/or scheduling, that might
   otherwise be over-subscribed and trigger the rejection of a
   reservation.

3.2.2.  Explicit routes

   In networks controlled by typical peer-to-peer protocols such as IEEE
   802.1 ISIS bridged networks or IETF OSPF routed networks, a network
   topology event in one part of the network can impact, at least
   briefly, the delivery of data in parts of the network remote from the
   failure or recovery event.  Thus, even redundant paths through a
   network, if controlled by the typical peer-to-peer protocols, do not
   eliminate the chances of brief losses of contact.

   Many real-time networks rely on physical rings or chains of two-port
   devices, with a relatively simple ring control protocol.  This
   supports redundant paths for service protection with a minimum of
   wiring.  As an additional benefit, ring topologies can often utilize
   different topology management protocols than those used for a mesh
   network, with a consequent reduction in the response time to topology

Finn, et al.               Expires May 3, 2018                  [Page 9]
Internet-Draft    Deterministic Networking Architecture     October 2017

   changes.  Of course, this comes at some cost in terms of increased
   hop count, and thus latency, for the typical path.

   In order to get the advantages of low hop count and still ensure
   against even very brief losses of connectivity, DetNet employs
   explicit routes, where the path taken by a given DetNet flow does not
   change, at least immediately, and likely not at all, in response to
   network topology events.  Service protection (Section 3.2.4) over
   explicit routes provides a high likelihood of continuous
   connectivity.  Explicit routes are commonly used in MPLS TE LSPs.

3.2.3.  Jitter Reduction

   A core objective of DetNet is to enable the convergence of Non-IP
   networks onto a common network infrastructure.  This requires the
   accurate emulation of currently deployed mission-specific networks,
   which typically rely on point-to-point analog (e.g. 4-20mA
   modulation) and serial-digital cables (or buses) for highly reliable,
   synchronized and jitter-free communications.  While the latency of
   analog transmissions is basically the speed of light, legacy serial
   links are usually slow (in the order of Kbps) compared to, say, GigE,
   and some latency is usually acceptable.  What is not acceptable is
   the introduction of excessive jitter, which may, for instance, affect
   the stability of control systems.

   Applications that are designed to operate on serial links usually do
   not provide services to recover the jitter, because jitter simply
   does not exists there.  Streams of information are expected to be
   delivered in-order and the precise time of reception influences the
   processes.  In order to converge such existing applications, there is
   a desire to emulate all properties of the serial cable, such as clock
   transportation, perfect flow isolation and fixed latency.  While
   minimal jitter (in the form of specifying minimum, as well as
   maximum, end-to-end latency) is supported by DetNet, there are
   practical limitations on packet-based networks in this regard.  In
   general, users are encouraged to use, instead of, "do this when you
   get the packet," a combination of:

   o  Sub-microsecond time synchronization among all source and
      destination end systems, and

   o  Time-of-execution fields in the application packets.

   Jitter reduction is provided by the mechanisms described in
   Section 4.5 that also provide congestion protection.

Finn, et al.               Expires May 3, 2018                 [Page 10]
Internet-Draft    Deterministic Networking Architecture     October 2017

3.2.4.  Packet Replication and Elimination

   After congestion loss has been eliminated, the most important causes
   of packet loss are random media and/or memory faults, and equipment
   failures.  Both causes of packet loss can be greatly reduced by
   spreading the data in a packet over multiple transmissions.  One such
   method for service protection is described in this section, which
   sends the same packets over multiple paths.

   Packet replication and elimination, also known as seamless redundancy
   [HSR-PRP], or 1+1 hitless protection, is a function of the DetNet
   service layer.  It involves three capabilities:

   o  Providing sequencing information, once, at or near the source, to
      the packets of a DetNet compound flow.  This may be done by adding
      a sequence number or time stamp as part of DetNet, or may be
      inherent in the packet, e.g. in a transport protocol, or
      associated to other physical properties such as the precise time
      (and radio channel) of reception of the packet.  Section 3.2.2.

   o  Replicating these packets into multiple DetNet member flows and,
      typically, sending them along at least two different paths to the
      destination(s), e.g. over the explicit routes of

   o  Eliminating duplicated packets.  This may be done at any step
      along the path to save network resources further down, in
      particular if multiple Replication points exist.  But the most
      common case is to perform this operation at the very edge of the
      DetNet network, preferably in or near the receiver.

   This function is a "hitless" version of, e.g., the 1+1 linear
   protection in [RFC6372].  That is, instead of switching from one flow
   to the other when a failure of a flow is detected, DetNet combines
   both flows, and performs a packet-by-packet selection of which to
   discard, based on sequence number.

   In the simplest case, this amounts to replicating each packet in a
   source that has two interfaces, and conveying them through the
   network, along separate paths, to the similarly dual-homed
   destinations, that discard the extras.  This ensures that one path
   (with zero congestion loss) remains, even if some intermediate node
   fails.  The sequence numbers can also be used for loss detection and
   for re-ordering.

   Detnet relay nodes in the network can provide replication and
   elimination facilities at various points in the network, so that
   multiple failures can be accommodated.

Finn, et al.               Expires May 3, 2018                 [Page 11]
Internet-Draft    Deterministic Networking Architecture     October 2017

   This is shown in the following figure, where the two relay nodes each
   replicate (R) the DetNet flow on input, sending the DetNet member
   flows to both the other relay node and to the end system, and
   eliminate duplicates (E) on the output interface to the right-hand
   end system.  Any one link in the network can fail, and the Detnet
   compound flow can still get through.  Furthermore, two links can
   fail, as long as they are in different segments of the network.

                    Packet replication and elimination

                > > > > > > > > > relay > > > > > > > >
               > /------------+ R node E +------------\ >
              > /                  v + ^               \ >
      end    R +                   v | ^                + E end
      system   +                   v | ^                +   system
              > \                  v + ^               / >
               > \------------+ R relay E +-----------/ >
                > > > > > > > > >  node > > > > > > > >

                                 Figure 1

   Packet replication and elimination does not react to and correct
   failures; it is entirely passive.  Thus, intermittent failures,
   mistakenly created packet filters, or misrouted data is handled just
   the same as the equipment failures that are detected handled by
   typical routing and bridging protocols.

   If packet replication and elimination is used over paths providing
   congestion protection (Section 3.2.1), and member flows that take
   different-length paths through the network are combined, a merge
   point may require extra buffering to equalize the delays over the
   different paths.  This equalization ensures that the resultant
   compound flow will not exceed its contracted bandwidth even after one
   or the other of the paths is restored after a failure.

3.3.  Secondary goals for DetNet

   Many applications require DetNet to provide additional services,
   including coesistence with other QoS mechanisms Section 3.3.1 and
   protection against misbehaving transmitters Section 3.3.2.

3.3.1.  Coexistence with normal traffic

   A DetNet network supports the dedication of a high proportion (e.g.
   75%) of the network bandwidth to DetNet flows.  But, no matter how
   much is dedicated for DetNet flows, it is a goal of DetNet to coexist
   with existing Class of Service schemes (e.g., DiffServ).  It is also

Finn, et al.               Expires May 3, 2018                 [Page 12]
Internet-Draft    Deterministic Networking Architecture     October 2017

   important that non-DetNet traffic not disrupt the DetNet flow, of
   course (see Section 3.3.2 and Section 5).  For these reasons:

   o  Bandwidth (transmission opportunities) not utilized by a DetNet
      flow are available to non-DetNet packets (though not to other
      DetNet flows).

   o  DetNet flows can be shaped or scheduled, in order to ensure that
      the highest-priority non-DetNet packet also is ensured a worst-
      case latency (at any given hop).

   o  When transmission opportunities for DetNet flows are scheduled in
      detail, then the algorithm constructing the schedule should leave
      sufficient opportunities for non-DetNet packets to satisfy the
      needs of the users of the network.  Detailed scheduling can also
      permit the time-shared use of buffer resources by different DetNet
      flows.

   Ideally, the net effect of the presence of DetNet flows in a network
   on the non-DetNet packets is primarily a reduction in the available
   bandwidth.

3.3.2.  Fault Mitigation

   One key to building robust real-time systems is to reduce the
   infinite variety of possible failures to a number that can be
   analyzed with reasonable confidence.  DetNet aids in the process by
   providing filters and policers to detect DetNet packets received on
   the wrong interface, or at the wrong time, or in too great a volume,
   and to then take actions such as discarding the offending packet,
   shutting down the offending DetNet flow, or shutting down the
   offending interface.

   It is also essential that filters and service remarking be employed
   at the network edge to prevent non-DetNet packets from being mistaken
   for DetNet packets, and thus impinging on the resources allocated to
   DetNet packets.

   There exist techniques, at present and/or in various stages of
   standardization, that can perform these fault mitigation tasks that
   deliver a high probability that misbehaving systems will have zero
   impact on well-behaved DetNet flows, except of course, for the
   receiving interface(s) immediately downstream of the misbehaving
   device.  Examples of such techniques include traffic policing
   functions (e.g.  [RFC2475]) and separating flows into per-flow rate-
   limited queues.

Finn, et al.               Expires May 3, 2018                 [Page 13]
Internet-Draft    Deterministic Networking Architecture     October 2017

4.  DetNet Architecture

4.1.  DetNet stack model

4.1.1.  Representative Protocol Stack Model

   Figure 2 illustrates a conceptual DetNet data plane layering model.
   One may compare it to that in [IEEE802.1CB], Annex C, a work in
   progress.

                     DetNet data plane protocol stack

             |  packets going  |        ^  packets coming   ^
             v down the stack  v        |   up the stack    |
           +----------------------+   +-----------------------+
           |        Source        |   |      Destination      |
           +----------------------+   +-----------------------+
           |    Service layer     |   |     Service layer     |
           |  Packet sequencing   |   | Duplicate elimination |
           |  Flow duplication    |   |      Flow merging     |
           |   Packet encoding    |   |    Packet decoding    |
           +----------------------+   +-----------------------+
           |   Transport layer    |   |    Transport layer    |
           |   Congestion prot.   |   |   Congestion prot.    |
           +----------------------+   +-----------------------+
           |     Lower layers     |   |     Lower layers      |
           +----------------------+   +-----------------------+
                      v                           ^
                       \_________________________/

                                 Figure 2

   Not all layers are required for any given application, or even for
   any given network.  The layers are, from top to bottom:

   Application
           Shown as "source" and "destination" in the diagram.

   OAM
           Operations, Administration, and Maintenance leverages in-band
           and out-of-and signaling that validates whether the service
           is effectively obtained within QoS constraints.  OAM is not
           shown in Figure 2; it may reside in any number of the layers.
           OAM can involve specific tagging added in the packets for
           tracing implementation or network configuration errors;
           traceability enables to find whether a packet is a replica,
           which relay node performed the replication, and which segment
           was intended for the replica.

Finn, et al.               Expires May 3, 2018                 [Page 14]
Internet-Draft    Deterministic Networking Architecture     October 2017

   Packet sequencing
           As part of DetNet service protection, supplies the sequence
           number for packet replication and elimination
           (Section 3.2.4).  Peers with Duplicate elimination.  This
           layer is not needed if a higher-layer transport protocol is
           expected to perform any packet sequencing and duplicate
           elimination required by the DetNet flow duplication.

   Duplicate elimination
           As part of the DetNet service layer, based on the sequenced
           number supplied by its peer, packet sequencing, Duplicate
           elimination discards any duplicate packets generated by
           DetNet flow duplication.  It can operate on member flows,
           compound flows, or both.  The duplication may also be
           inferred from other information such as the precise time of
           reception in a scheduled network.  The duplicate elimination
           layer may also perform resequencing of packets to restore
           packet order in a flow that was disrupted by the loss of
           packets on one or another of the multiple paths taken.

   Flow duplication
           As part of DetNet service protection, packets that belong to
           a DetNet compound flow are replicated into two or more DetNet
           member flows.  This function is separate from packet
           sequencing.  Flow duplication can be an explicit duplication
           and remarking of packets, or can be performed by, for
           example, techniques similar to ordinary multicast
           replication.  Peers with DetNet flow merging.

   Network flow merging
           As part of DetNet service protection, merges DetNet member
           flows together for packets coming up the stack belonging to a
           specific DetNet compound flow.  Peers with DetNet flow
           duplication.  DetNet flow merging, together with packet
           sequencing, duplicate elimination, and DetNet flow
           duplication, performs packet replication and elimination
           (Section 3.2.4).

   Packet encoding
           As part of DetNet service protection, as an alternative to
           packet sequencing and flow duplication, packet encoding
           combines the information in multiple DetNet packets, perhaps
           from different DetNet compound flows, and transmits that
           information in packets on different DetNet member Flows.
           Peers with Packet decoding.

   Packet decoding

Finn, et al.               Expires May 3, 2018                 [Page 15]
Internet-Draft    Deterministic Networking Architecture     October 2017

           As part of DetNet service protection, as an alternative to
           flow merging and duplicate elimination, packet decoding takes
           packets from different DetNet member flows, and computes from
           those packets the original DetNet packets from the compound
           flows input to packet encoding.  Peers with Packet encoding.

   Congestion protection
           The DetNet transport layer provides congestion protection.
           See Section 4.5.  The actual queuing and shaping mechanisms
           are typically provided by underlying subnet layers, but since
           these are can be closely associated with the means of
           providing paths for DetNet flows (e.g.  MPLS LSPs or {VLAN,
           multicast destination MAC address} pairs), the path and the
           congestion protection are conflated in this figure.

   The packet sequencing and duplication elimination functions at the
   source and destination ends of a DetNet compound flow may be
   performed either in the end system or in a DetNet edge node.  The
   reader must not confuse a DetNet edge function with other kinds of
   edge functions, e.g. an Label Edge Router, although the two functions
   may be performed together.  The DetNet edge function is concerned
   with sequencing packets belonging to DetNet flows.  The LER with
   encapsulating/decapsulating packets for transport, and is considered
   part of the network underlying the DetNet transport layer.

4.1.2.  DetNet Data Plane Overview

   A "Deterministic Network" will be composed of DetNet enabled nodes
   i.e., End Systems, Edge Nodes, Relay Nodes and collectively deliver
   DetNet services.  DetNet enabled nodes are interconnected via Transit
   Nodes (i.e., routers) which support DetNet, but are not DetNet
   service aware.  Transit nodes see DetNet nodes as end points.  All
   DetNet enabled nodes are connect to sub-networks, where a point-to-
   point link is also considered as a simple sub-network.  These sub-
   networks will provide DetNet compatible service for support of DetNet
   traffic.  Examples of sub-networks include IEEE 802.1 TSN and OTN.
   Of course, multi-layer DetNet systems may also be possible, where one
   DetNet appears as a sub-network, and provides service to, a higher
   layer DetNet system.  A simple DetNet concept network is shown in
   Figure 3.

Finn, et al.               Expires May 3, 2018                 [Page 16]
Internet-Draft    Deterministic Networking Architecture     October 2017

  TSN              Edge          Transit        Relay        DetNet
  End System       Node            Node         Node         End System

  +---------+    +.........+                                 +---------+
  |  Appl.  |<---:Svc Proxy:-- End to End Service ---------->|  Appl.  |
  +---------+    +---------+                   +---------+   +---------+
  |   TSN   |    |TSN| |Svc|<-- DetNet flow ---: Service :-->| Service |
  +---------+    +---+ +---+    +---------+    +---------+   +---------+
  |Transport|    |Trp| |Trp|    |Transport|    |Trp| |Trp|   |Transport|
  +-------.-+    +-.-+ +-.-+    +--.----.-+    +-.-+ +-.-+   +---.-----+
          :  Link  :    /  ,-----.  \   :  Link  :    /  ,-----.  \
          +........+    +-[  Sub  ]-+   +........+    +-[  Sub  ]-+
                          [Network]                     [Network]
                           `-----'                       `-----'

                 Figure 3: A Simple DetNet Enabled Network

   Distinguishing the function of these two DetNet data plane layers,
   the DetNet service layer and the DetNet transport layer, helps to
   explore and evaluate various combinations of the data plane solutions
   available.  This separation of DetNet layers, while helpful, should
   not be considered as formal requirement.  For example, some
   technologies may violate these strict layers and still be able to
   deliver a DetNet service.

               .
               .
           +-----------+
           |  Service  | PW, RTP/(UDP), GRE
           +-----------+
           | Transport | (UDP)/IPv6, (UDP)/IPv4, MPLS LSPs, BIER
           +-----------+
               .
               .

                 Figure 4: DetNet adaptation to data plane

   In some networking scenarios, the end system initially provides a
   DetNet flow encapsulation, which contains all information needed by
   DetNet nodes (e.g., Real-time Transport Protocol (RTP) [RFC3550]
   based DetNet flow transported over a native UDP/IP network or
   PseudoWire).  In other scenarios, the encapsulation formats might
   differ significantly.  As an example, a CPRI "application's" I/Q data
   mapped directly to Ethernet frames may have to be transported over an
   MPLS-based packet switched network (PSN).

   There are many valid options to create a data plane solution for
   DetNet traffic by selecting a technology approach for the DetNet

Finn, et al.               Expires May 3, 2018                 [Page 17]
Internet-Draft    Deterministic Networking Architecture     October 2017

   service layer and also selecting a technology approach for the DetNet
   transport layer.  There are a high number of valid combinations.

   One of the most fundamental differences between different potential
   data plane options is the basic addressing and headers used by DetNet
   end systems.  For example, is the basic service a Layer 2 (e.g.,
   Ethernet) or Layer 3 (i.e., IP) service.  This decision impacts how
   DetNet end systems are addressed, and the basic forwarding logic for
   the DetNet service layer.

4.1.3.  Network reference model

   The figure below shows another view of the DetNet service related
   reference points and main components (Figure 5).

DetNet                                                        DetNet
end system                                                    end system
   _                                                                _
  / \     +----DetNet-UNI (U)                                      / \
 /App\    |                                                       /App\
/-----\   |                                                      /-----\
| NIC |   v         ________                                     | NIC |
+--+--+   _____    /        \               DetNet-UNI (U) --+   +--+--+
   |     /     \__/          \                               |      |
   |    / +----+    +----+    \_____                         |      |
   |   /  |    |    |    |          \_______                 |      |
   +------U PE +----+ P  +----+             \            _   v      |
       |  |    |    |    |    |              |       ___/ \         |
       |  +--+-+    +----+    |       +----+ |      /      \_       |
       \     |                |       |    | |     /         \      |
        \    |   +----+    +--+-+  +--+PE  |--------         U------+
         \   |   |    |    |    |  |  |    | |     \_      _/
          \  +---+ P  +----+ P  +--+  +----+ |       \____/
           \___  |    |    |    |           /
               \ +----+__  +----+     DetNet-1      DetNet-2
   |            \_____/  \___________/                              |
   |                                                                |
   |      |     End-to-End-Service         |       |         |      |
   <---------------------------------------------------------------->
   |      |     DetNet-Service             |       |         |      |
   |      <-------------------------------------------------->      |
   |      |                                |       |         |      |

          Figure 5: DetNet Service Reference Model (multi-domain)

   DetNet-UNIs ("U" in Figure 5) are assumed in this document to be
   packet-based reference points and provide connectivity over the
   packet network.  A DetNet-UNI may provide multiple functions, e.g.,

Finn, et al.               Expires May 3, 2018                 [Page 18]
Internet-Draft    Deterministic Networking Architecture     October 2017

   it may add networking technology specific encapsulation to the DetNet
   flows if necessary; it may provide status of the availability of the
   connection associated to a reservation; it may provide a
   synchronization service for the end system; it may carry enough
   signaling to place the reservation in a network without a controller,
   or if the controller only deals with the network but not the end
   points.  Internal reference points of end systems (between the
   application and the NIC) are more challenging from control
   perspective and they may have extra requirements (e.g., in-order
   delivery is expected in end system internal reference points, whereas
   it is considered optional over the DetNet-UNI), therefore not covered
   in this document.

4.2.  DetNet systems

4.2.1.  End system

   The native data flow between the source/destination end systems is
   referred to as application-flow (App-flow).  The traffic
   characteristics of an App-flow can be CBR (constant bit rate) or VBR
   (variable bit rate) and can have L1 or L2 or L3 encapsulation (e.g.,
   TDM (time-division multiplexing), Ethernet, IP).  These
   characteristics are considered as input for resource reservation and
   might be simplified to ensure determinism during transport (e.g.,
   making reservations for the peak rate of VBR traffic, etc.).

   An end system may or may not be DetNet transport layer aware or
   DetNet service layer aware.  That is, an end system may or may not
   contain DetNet specific functionality.  End systems with DetNet
   functionalities may have the same or different transport layer as the
   connected DetNet domain.  Grouping of end systems are shown in
   Figure 6.

Finn, et al.               Expires May 3, 2018                 [Page 19]
Internet-Draft    Deterministic Networking Architecture     October 2017

                End system
                    |
                    |
                    |  DetNet aware ?
                   / \
           +------<   >------+
        NO |       \ /       | YES
           |        v        |
    DetNet unaware           |
      End system             |
                             | Service/
                             | Transport
                            / \  aware ?
                  +--------<   >-------------+
          t-aware |         \ /              | s-aware
                  |          v               |
                  |          | both          |
                  |          |               |
          DetNet t-aware     |        DetNet s-aware
            End system       |         End system
                             v
                       DetNet st-aware
                         End system

                     Figure 6: Grouping of end systems

   Note some known use cases for end systems:

   o  DetNet unaware: The classic case requiring network proxies.

   o  DetNet t-aware: An extant TSN system.  It knows about some TSN
      functions (e.g., reservation), but not about replication/
      elimination.

   o  DetNet s-aware: An extant IEC 62439-3 system.  It supplies
      sequence numbers, but doesn't know about zero congestion loss.

   o  DetNet st-aware: A full functioning DetNet end station, it has
      DetNet functionalities and usually the same forwarding paradigm as
      the connected DetNet domain.  It can be treated as an integral
      part of the DetNet domain .

4.2.2.  DetNet edge, relay, and transit nodes

   As shown in Figure 3, DetNet edge nodes providing proxy service and
   DetNet relay nodes providing the DetNet service layer are DetNet-
   aware, and DetNet transit nodes need only be aware of the DetNet
   transport layer.

Finn, et al.               Expires May 3, 2018                 [Page 20]
Internet-Draft    Deterministic Networking Architecture     October 2017

   In general, if a DetNet flow passes through one or more DetNet-
   unaware network node between two DetNet nodes providing the DetNet
   transport layer for that flow, there is a potential for disruption or
   failure of the DetNet QoS.  A network administrator needs to ensure
   that the DetNet-unaware network nodes are configured to minimize the
   chances of packet loss and delay, and provision enough exra buffer
   space in the DetNet transit node following the DetNet-unaware network
   nodes to absorb the induced latency variations.

4.3.  DetNet flows

4.3.1.  DetNet flow types

   A DetNet flow can have different formats during while it is
   transported between the peer end systems.  Therefore, the following
   possible types / formats of a DetNet flow are distinguished in this
   document:

   o  App-flow: native format of a DetNet flow.  It does not contain any
      DetNet related attributes.

   o  DetNet-t-flow: specific format of a DetNet flow.  Only requires
      the congestion / latency features provided by the Detnet transport
      layer.

   o  DetNet-s-flow: specific format of a DetNet flow.  Only requires
      the replication/elimination feature ensured by the DetNet service
      layer.

   o  DetNet-st-flow: specific format of a DetNet flow.  It requires
      both DetNet service layer and DetNet transport layer functions
      during forwarding.

4.3.2.  Source guarantees

   For the purposes of congestion protection, DetNet flows can be
   synchronous or asynchronous.  In synchronous DetNet flows, at least
   the intermediate nodes (and possibly the end systems) are closely
   time synchronized, typically to better than 1 microsecond.  By
   transmitting packets from different DetNet flows or classes of DetNet
   flows at different times, using repeating schedules synchronized
   among the intermediate nodes, resources such as buffers and link
   bandwidth can be shared over the time domain among different DetNet
   flows.  There is a tradeoff among techniques for synchronous DetNet
   flows between the burden of fine-grained scheduling and the benefit
   of reducing the required resources, especially buffer space.

Finn, et al.               Expires May 3, 2018                 [Page 21]
Internet-Draft    Deterministic Networking Architecture     October 2017

   In contrast, asynchronous DetNet flows are not coordinated with a
   fine-grained schedule, so relay and end systems must assume worst-
   case interference among DetNet flows contending for buffer resources.
   Asynchronous DetNet flows are characterized by:

   o  A maximum packet size;

   o  An observation interval; and

   o  A maximum number of transmissions during that observation
      interval.

   These parameters, together with knowledge of the protocol stack used
   (and thus the size of the various headers added to a packet), limit
   the number of bit times per observation interval that the DetNet flow
   can occupy the physical medium.

   The source promises that these limits will not be exceeded.  If the
   source transmits less data than this limit allows, the unused
   resources such as link bandwidth can be made available by the system
   to non-DetNet packets.  However, making those resources available to
   DetNet packets in other DetNet flows would serve no purpose.  Those
   other DetNet flows have their own dedicated resources, on the
   assumption that all DetNet flows can use all of their resources over
   a long period of time.

   There is no provision in DetNet for throttling DetNet flows (reducing
   the transmission rate via feedback); the assumption is that a DetNet
   flow, to be useful, must be delivered in its entirety.  That is,
   while any useful application is written to expect a certain number of
   lost packets, the real-time applications of interest to DetNet demand
   that the loss of data due to the network is extraordinarily
   infrequent.

   Although DetNet strives to minimize the changes required of an
   application to allow it to shift from a special-purpose digital
   network to an Internet Protocol network, one fundamental shift in the
   behavior of network applications is impossible to avoid: the
   reservation of resources before the application starts.  In the first
   place, a network cannot deliver finite latency and practically zero
   packet loss to an arbitrarily high offered load.  Secondly, achieving
   practically zero packet loss for unthrottled (though bandwidth
   limited) DetNet flows means that bridges and routers have to dedicate
   buffer resources to specific DetNet flows or to classes of DetNet
   flows.  The requirements of each reservation have to be translated
   into the parameters that control each system's queuing, shaping, and
   scheduling functions and delivered to the hosts, bridges, and
   routers.

Finn, et al.               Expires May 3, 2018                 [Page 22]
Internet-Draft    Deterministic Networking Architecture     October 2017

4.3.3.  Incomplete Networks

   The presence in the network of transit nodes or subnets that are not
   fully capable of offering DetNet services complicates the ability of
   the intermediate nodes and/or controller to allocate resources, as
   extra buffering, and thus extra latency, must be allocated at points
   downstream from the non-DetNet intermediate node for a DetNet flow.

4.4.  Traffic Engineering for DetNet

   Traffic Engineering Architecture and Signaling (TEAS) [TEAS] defines
   traffic-engineering architectures for generic applicability across
   packet and non-packet networks.  From TEAS perspective, Traffic
   Engineering (TE) refers to techniques that enable operators to
   control how specific traffic flows are treated within their networks.

   Because if its very nature of establishing explicit optimized paths,
   Deterministic Networking can be seen as a new, specialized branch of
   Traffic Engineering, and inherits its architecture with a separation
   into planes.

   The Deterministic Networking architecture is thus composed of three
   planes, a (User) Application Plane, a Controller Plane, and a Network
   Plane, which echoes that of Figure 1 of Software-Defined Networking
   (SDN): Layers and Architecture Terminology [RFC7426].:

4.4.1.  The Application Plane

   Per [RFC7426], the Application Plane includes both applications and
   services.  In particular, the Application Plane incorporates the User
   Agent, a specialized application that interacts with the end user /
   operator and performs requests for Deterministic Networking services
   via an abstract Flow Management Entity, (FME) which may or may not be
   collocated with (one of) the end systems.

   At the Application Plane, a management interface enables the
   negotiation of flows between end systems.  An abstraction of the flow
   called a Traffic Specification (TSpec) provides the representation.
   This abstraction is used to place a reservation over the (Northbound)
   Service Interface and within the Application plane.  It is associated
   with an abstraction of location, such as IP addresses and DNS names,
   to identify the end systems and eventually specify intermediate
   nodes.

Finn, et al.               Expires May 3, 2018                 [Page 23]
Internet-Draft    Deterministic Networking Architecture     October 2017

4.4.2.  The Controller Plane

   The Controller Plane corresponds to the aggregation of the Control
   and Management Planes in [RFC7426], though Common Control and
   Measurement Plane (CCAMP) [CCAMP] makes an additional distinction
   between management and measurement.  When the logical separation of
   the Control, Measurement and other Management entities is not
   relevant, the term Controller Plane is used for simplicity to
   represent them all, and the term controller refers to any device
   operating in that plane, whether is it a Path Computation entity or a
   Network Management entity (NME).  The Path Computation Element (PCE)
   [PCE] is a core element of a controller, in charge of computing
   Deterministic paths to be applied in the Network Plane.

   A (Northbound) Service Interface enables applications in the
   Application Plane to communicate with the entities in the Controller
   Plane.

   One or more PCE(s) collaborate to implement the requests from the FME
   as Per-Flow Per-Hop Behaviors installed in the intermediate nodes for
   each individual flow.  The PCEs place each flow along a deterministic
   sequence of intermediate nodes so as to respect per-flow constraints
   such as security and latency, and optimize the overall result for
   metrics such as an abstract aggregated cost.  The deterministic
   sequence can typically be more complex than a direct sequence and
   include redundancy path, with one or more packet replication and
   elimination points.

4.4.3.  The Network Plane

   The Network Plane represents the network devices and protocols as a
   whole, regardless of the Layer at which the network devices operate.
   It includes Forwarding Plane (data plane), Application, and
   Operational Plane (control plane) aspects.

   The network Plane comprises the Network Interface Cards (NIC) in the
   end systems, which are typically IP hosts, and intermediate nodes,
   which are typically IP routers and switches.  Network-to-Network
   Interfaces such as used for Traffic Engineering path reservation in
   [RFC5921], as well as User-to-Network Interfaces (UNI) such as
   provided by the Local Management Interface (LMI) between network and
   end systems, are both part of the Network Plane, both in the control
   plane and the data plane.

   A Southbound (Network) Interface enables the entities in the
   Controller Plane to communicate with devices in the Network Plane.
   This interface leverages and extends TEAS to describe the physical
   topology and resources in the Network Plane.

Finn, et al.               Expires May 3, 2018                 [Page 24]
Internet-Draft    Deterministic Networking Architecture     October 2017

                          Flow Management Entity

       End                                                     End
       System                                               System

      -+-+-+-+-+-+-+ Northbound -+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

                PCE         PCE              PCE              PCE

      -+-+-+-+-+-+-+ Southbound -+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

              intermediate  intermed.   intermed.  intermed.
                  Node       Node       Node       Node
       NIC                                                     NIC
              intermediate  intermed.   intermed.  intermed.
                  Node       Node       Node       Node

                                 Figure 7

   The intermediate nodes (and eventually the end systems NIC) expose
   their capabilities and physical resources to the controller (the
   PCE), and update the PCE with their dynamic perception of the
   topology, across the Southbound Interface.  In return, the PCE(s) set
   the per-flow paths up, providing a Flow Characterization that is more
   tightly coupled to the intermediate node Operation than a TSpec.

   At the Network plane, intermediate nodes may exchange information
   regarding the state of the paths, between adjacent systems and
   eventually with the end systems, and forward packets within
   constraints associated to each flow, or, when unable to do so,
   perform a last resort operation such as drop or declassify.

   This specification focuses on the Southbound interface and the
   operation of the Network Plane.

4.5.  Queuing, Shaping, Scheduling, and Preemption

   DetNet achieves congestion protection and bounded delivery latency by
   reserving bandwidth and buffer resources at every hop along the path
   of the DetNet flow.  The reservation itself is not sufficient,
   however.  Implementors and users of a number of proprietary and
   standard real-time networks have found that standards for specific
   data plane techniques are required to enable these assurances to be
   made in a multi-vendor network.  The fundamental reason is that
   latency variation in one system results in the need for extra buffer
   space in the next-hop system(s), which in turn, increases the worst-
   case per-hop latency.

Finn, et al.               Expires May 3, 2018                 [Page 25]
Internet-Draft    Deterministic Networking Architecture     October 2017

   Standard queuing and transmission selection algorithms allow a
   central controller to compute the latency contribution of each
   transit node to the end-to-end latency, to compute the amount of
   buffer space required in each transit node for each incremental
   DetNet flow, and most importantly, to translate from a flow
   specification to a set of values for the managed objects that control
   each relay or end system.  The IEEE 802 has specified (and is
   specifying) a set of queuing, shaping, and scheduling algorithms that
   enable each transit node (bridge or router), and/or a central
   controller, to compute these values.  These algorithms include:

   o  A credit-based shaper [IEEE802.1Q-2014] Clause 34.

   o  Time-gated queues governed by a rotating time schedule,
      synchronized among all transit nodes [IEEE802.1Qbv].

   o  Synchronized double (or triple) buffers driven by synchronized
      time ticks.  [IEEE802.1Qch].

   o  Pre-emption of an Ethernet packet in transmission by a packet with
      a more stringent latency requirement, followed by the resumption
      of the preempted packet [IEEE802.1Qbu], [IEEE802.3br].

   While these techniques are currently embedded in Ethernet and
   bridging standards, we can note that they are all, except perhaps for
   packet preemption, equally applicable to other media than Ethernet,
   and to routers as well as bridges.

4.6.  Service instance

   A Service instance represents all the functions required on a node to
   allow the end-to-end service between the UNIs.

   The DetNet network reference model is shown in Figure 8 for a DetNet-
   Service scenario (i.e. between two DetNet-UNIs).  In this figure, the
   end systems ("A" and "B") are connected directly to the edge nodes of
   the IP/MPLS network ("PE1" and "PE2").  End-systems participating
   DetNet communication may require connectivity before setting up an
   App-flow that requires the DetNet service.  Such a connectivity
   related service instance and the one dedicated for DetNet service
   share the same access.  Packets belonging to a DetNet flow are
   selected by a filter configured on the access ("F1" and "F2").  As a
   result, data flow specific access ("access-A + F1" and "access-B +
   F2") are terminated in the flow specific service instance ("SI-1" and
   "SI-2").  A tunnel is used to provide connectivity between the
   service instances.

Finn, et al.               Expires May 3, 2018                 [Page 26]
Internet-Draft    Deterministic Networking Architecture     October 2017

   The tunnel is used to transport exclusively the packets of the DetNet
   flow between "SI-1" and "SI-2".  The service instances are configured
   to implement DetNet functions and a flow specific routing or bridging
   function depending on what connectivity the participating end systems
   require (L3 or L2).  The service instance and the tunnel may or may
   not be shared by multiple DetNet flows.  Sharing the service instance
   by multiple DetNet flows requires properly populated forwarding
   tables of the service instance.

          access-A                                      access-B
           <----->    <---------- tunnel ---------->     <----->

              +---------+          ___  _         +---------+
End system    |  +----+ |         /   \/ \_       | +----+  | End system
    "A" -------F1+    | |        /         \      | |    +F2----- "B"
              |  |    +==========+ IP/MPLS +========+    |  |
              |  |SI-1| |        \__  Net._/      | |SI-2|  |
              |  +----+ |           \____/        | +----+  |
              |PE1      |                         |      PE2|
              +---------+                         +---------+

                 Figure 8: DetNet network reference model

   The tunnel between the service instances may have some special
   characteristics.  For example, in case of a "packet PW" based tunnel,
   there are differences in the usage of the packet PW for DetNet
   traffic compared to the network model described in [RFC6658].  In the
   DetNet scenario, the packet PW is used exclusively by the DetNet
   flow, whereas [RFC6658] states: "The packet PW appears as a single
   point-to-point link to the client layer.  Network-layer adjacency
   formation and maintenance between the client equipments will follow
   the normal practice needed to support the required relationship in
   the client layer ... This packet pseudowire is used to transport all
   of the required layer 2 and layer 3 protocols between LSR1 and LSR2".

4.7.  Flow identification at technology borders

4.7.1.  Exporting flow identification

   An interesting feature of DetNet, and one that invites
   implementations that can be accused of "layering violations", is the
   need for lower layers to be aware of specific flows at higher layers,
   in order to provide specific queuing and shaping services for
   specific flows.  For example:

Finn, et al.               Expires May 3, 2018                 [Page 27]
Internet-Draft    Deterministic Networking Architecture     October 2017

   o  A non-IP, strictly L2 source end system X may be sending multiple
      flows to the same L2 destination end system Y.  Those flows may
      include DetNet flows with different QoS requirements, and may
      include non-DetNet flows.

   o  A router may be sending any number of flows to another router.
      Again, those flows may include DetNet flows with different QoS
      requirements, and may include non-DetNet flows.

   o  Two routers may be separated by bridges.  For these bridges to
      perform any required per-flow queuing and shaping, they must be
      able to identify the individual flows.

   o  A Label Edge Router (LERs) may have a Label Switched Path (LSP)
      set up for handling traffic destined for a particular IP address
      carrying only non-DetNet flows.  If a DetNet flow to that same
      address is requested, a separate LSP may be needed, in order that
      all of the Label Switch Routers (LSRs) along the path to the
      destination give that flow special queuing and shaping.

   The need for a lower-level DetNet node to be aware of individual
   higher-layer flows is not unique to DetNet.  But, given the endless
   complexity of layering and relayering over tunnels that is available
   to network designers, DetNet needs to provide a model for flow
   identification that is at least somewhat better than packet
   inspection.  That is not to say that packet inspection to layer 4 or
   5 addresses will not be used, or the capability standardized; but,
   there are alternatives.

   A DetNet relay node can connect DetNet flows on different paths using
   different flow identification methods.  For example:

   o  A single unicast DetNet flow passing from router A through a
      bridged network to router B may be assigned a {VLAN, multicast
      destination MAC address} pair that is unique within that bridged
      network.  The bridges can then identify the flow without accessing
      higher-layer headers.  Of course, the receiving router must
      recognize and accept that multicast MAC address.

   o  A DetNet flow passing from LSR A to LSR B may be assigned a
      different label than that used for other flows to the same IP
      destination.

   In any of the above cases, it is possible that an existing DetNet
   flow can be used as a carrier for multiple DetNet sub-flows.  (Not to
   be confused with DetNet compound vs. member flows.)  Of course, this
   requires that the aggregate DetNet flow be provisioned properly to
   carry the sub-flows.

Finn, et al.               Expires May 3, 2018                 [Page 28]
Internet-Draft    Deterministic Networking Architecture     October 2017

   Thus, rather than packet inspection, there is the option to export
   higher-layer information to the lower layer.  The requirement to
   support one or the other method for flow identification (or both) is
   the essential complexity that DetNet brings to existing control plane
   models.

4.7.2.  Flow attribute mapping between layers

   Transport of DetNet flows over multiple technology domains may
   require that lower layers are aware of specific flows of higher
   layers.  Such an "exporting of flow identification" is needed each
   time when the forwarding paradigm is changed on the transport path
   (e.g., two LSRs are interconnected by a L2 bridged domain, etc.).
   The three main forwarding methods considered for deterministic
   networking are:

   o  IP routing

   o  MPLS label switching

   o  Ethernet bridging

        add/remove     add/remove
        Eth Flow-ID    IP Flow-ID
            |             |
            v             v
         +-----------------------------------------------------------+
         |      |      |      |                                      |
         | Eth  | MPLS |  IP  |     Application data                 |
         |      |      |      |                                      |
         +-----------------------------------------------------------+
                   ^
                   |
               add/remove
              MPLS Flow-ID

                  Figure 9: Packet with multiple Flow-IDs

   The additional (domain specific) Flow-ID can be

   o  created by a domain specific function or

   o  derived from the Flow-ID added to the App-flow,

   so that it must be unique inside the given domain.  Note that the
   Flow-ID added to the App-flow is still present in the packet, but
   transport nodes may lack the function to recognize it; that's why the
   additional Flow-ID is added (pushed).

Finn, et al.               Expires May 3, 2018                 [Page 29]
Internet-Draft    Deterministic Networking Architecture     October 2017

4.7.3.  Flow-ID mapping examples

   IP nodes and MPLS nodes are assumed to be configured to push such an
   additional (domain specific) Flow-ID when sending traffic to an
   Ethernet switch (as shown in the examples below).

   Figure 10 shows a scenario where an IP end system ("IP-A") is
   connected via two Ethernet switches ("ETH-n") to an IP router ("IP-
   1").

                                     IP domain
                  <-----------------------------------------------

           +======+                                       +======+
           |L3-ID |                                       |L3-ID |
           +======+  /\                           +-----+ +======+
                    /  \       Forward as         |     |
                   /IP-A\      per ETH-ID         |IP-1 |      Recognize
   Push  ------>  +-+----+         |              +---+-+  <----- ETH-ID
   ETH-ID           |         +----+-----+            |
                    |         v          v            |
                    |      +-----+    +-----+         |
                    +------+     |    |     +---------+
           +......+        |ETH-1+----+ETH-2|           +======+
           .L3-ID .        +-----+    +-----+           |L3-ID |
           +======+             +......+                +======+
           |ETH-ID|             .L3-ID .                |ETH-ID|
           +======+             +======+                +------+
                                |ETH-ID|
                                +======+

                             Ethernet domain
                           <---------------->

         Figure 10: IP nodes interconnected by an Ethernet domain

   End system "IP-A" uses the original App-flow specific ID ("L3-ID"),
   but as it is connected to an Ethernet domain it has to push an
   Ethernet-domain specific flow-ID ("VID + multicast MAC address",
   referred as "ETH-ID") before sending the packet to "ETH-1" node.
   Ethernet switch "ETH-1" can recognize the data flow based on the
   "ETH-ID" and it does forwarding toward "ETH-2".  "ETH-2" switches the
   packet toward the IP router.  "IP-1" must be configured to receive
   the Ethernet Flow-ID specific multicast stream, but (as it is an L3
   node) it decodes the data flow ID based on the "L3-ID" fields of the
   received packet.

Finn, et al.               Expires May 3, 2018                 [Page 30]
Internet-Draft    Deterministic Networking Architecture     October 2017

   Figure 11 shows a scenario where MPLS domain nodes ("PE-n" and "P-m")
   are connected via two Ethernet switches ("ETH-n").

                                    MPLS domain
                  <----------------------------------------------->

       +=======+                                  +=======+
       |MPLS-ID|                                  |MPLS-ID|
       +=======+  +-----+                 +-----+ +=======+ +-----+
                  |     |   Forward as    |     |           |     |
                  |PE-1 |   per ETH-ID    | P-2 +-----------+ PE-2|
   Push   ----->  +-+---+        |        +---+-+           +-----+
   ETH-ID           |      +-----+----+       |  \ Recognize
                    |      v          v       |   +-- ETH-ID
                    |   +-----+    +-----+    |
                    +---+     |    |     +----+
           +.......+    |ETH-1+----+ETH-2|   +=======+
           .MPLS-ID.    +-----+    +-----+   |MPLS-ID|
           +=======+                         +=======+
           |ETH-ID |         +.......+       |ETH-ID |
           +=======+         .MPLS-ID.       +-------+
                             +=======+
                             |ETH-ID |
                             +=======+
                          Ethernet domain
                        <---------------->

        Figure 11: MPLS nodes interconnected by an Ethernet domain

   "PE-1" uses the MPLS specific ID ("MPLS-ID"), but as it is connected
   to an Ethernet domain it has to push an Ethernet-domain specific
   flow-ID ("VID + multicast MAC address", referred as "ETH-ID") before
   sending the packet to "ETH-1".  Ethernet switch "ETH-1" can recognize
   the data flow based on the "ETH-ID" and it does forwarding toward
   "ETH-2".  "ETH-2" switches the packet toward the MPLS node ("P-2").
   "P-2" must be configured to receive the Ethernet Flow-ID specific
   multicast stream, but (as it is an MPLS node) it decodes the data
   flow ID based on the "MPLS-ID" fields of the received packet.

   One can appreciate from the above example that, when the means used
   for DetNet flow identifcation is altered or exported, the means for
   encoding the sequence number information must similarly be altered or
   exported.

Finn, et al.               Expires May 3, 2018                 [Page 31]
Internet-Draft    Deterministic Networking Architecture     October 2017

4.8.  Advertising resources, capabilities and adjacencies

   There are three classes of information that a central controller or
   decentralized control plane needs to know that can only be obtained
   from the end systems and/or transit nodes in the network.  When using
   a peer-to-peer control plane, some of this information may be
   required by a system's neighbors in the network.

   o  Details of the system's capabilities that are required in order to
      accurately allocate that system's resources, as well as other
      systems' resources.  This includes, for example, which specific
      queuing and shaping algorithms are implemented (Section 4.5), the
      number of buffers dedicated for DetNet allocation, and the worst-
      case forwarding delay.

   o  The dynamic state of an end or transit node's DetNet resources.

   o  The identity of the system's neighbors, and the characteristics of
      the link(s) between the systems, including the length (in
      nanoseconds) of the link(s).

4.9.  Provisioning model

4.9.1.  Centralized Path Computation and Installation

   A centralized routing model, such as provided with a PCE (RFC 4655
   [RFC4655]), enables global and per-flow optimizations.  (See
   Section 4.4.)  The model is attractive but a number of issues are
   left to be solved.  In particular:

   o  Whether and how the path computation can be installed by 1) an end
      device or 2) a Network Management entity,

   o  And how the path is set up, either by installing state at each hop
      with a direct interaction between the forwarding device and the
      PCE, or along a path by injecting a source-routed request at one
      end of the path.

4.9.2.  Distributed Path Setup

   Significant work on distributed path setup can be leveraged from MPLS
   Traffic Engineering, in both its GMPLS and non-GMPLS forms.  The
   protocols within scope are Resource ReSerVation Protocol [RFC3209]
   [RFC3473](RSVP-TE), OSPF-TE [RFC4203] [RFC5392] and ISIS-TE [RFC5307]
   [RFC5316].  These should be viewed as starting points as there are
   feature specific extensions defined that may be applicable to DetNet.

Finn, et al.               Expires May 3, 2018                 [Page 32]
Internet-Draft    Deterministic Networking Architecture     October 2017

   In a Layer-2 only environment, or as part of a layered approach to a
   mixed environment, IEEE 802.1 also has work, either completed or in
   progress.  [IEEE802.1Q-2014] Clause 35 describes SRP, a peer-to-peer
   protocol for Layer-2 roughly analogous to RSVP [RFC2205].
   [IEEE802.1Qca] defines how ISIS can provide multiple disjoint paths
   or distribution trees.  Also in progress is [IEEE802.1Qcc], which
   expands the capabilities of SRP.

   The integration/interaction of the DetNet control layer with an
   underlying IEEE 802.1 sub-network control layer will need to be
   defined.

4.10.  Scaling to larger networks

   Reservations for individual DetNet flows require considerable state
   information in each transit node, especially when adequate fault
   mitigation (Section 3.3.2) is required.  The DetNet data plane, in
   order to support larger numbers of DetNet flows, must support the
   aggregation of DetNet flows into tunnels, which themselves can be
   viewed by the transit nodes' data planes largely as individual DetNet
   flows.  Without such aggregation, the per-relay system may limit the
   scale of DetNet networks.

4.11.  Connected islands vs. networks

   Given that users have deployed examples of the IEEE 802.1 TSN TG
   standards, which provide capabilities similar to DetNet, it is
   obvious to ask whether the IETF DetNet effort can be limited to
   providing Layer-2 connections (VPNs) between islands of bridged TSN
   networks.  While this capability is certainly useful to some
   applications, and must not be precluded by DetNet, tunneling alone is
   not a sufficient goal for the DetNet WG.  As shown in the
   Deterministic Networking Use Cases draft [I-D.ietf-detnet-use-cases],
   there are already deployments of Layer-2 TSN networks that are
   encountering the well-known problems of over-large broadcast domains.
   Routed solutions, and combinations routed/bridged solutions, are both
   required.

4.12.  Compatibility with Layer-2

   Standards providing similar capabilities for bridged networks (only)
   have been and are being generated in the IEEE 802 LAN/MAN Standards
   Committee.  The present architecture describes an abstract model that
   can be applicable both at Layer-2 and Layer-3, and over links not
   defined by IEEE 802.  It is the intention of the authors (and
   hopefully, as this draft progresses, of the DetNet Working Group)
   that IETF and IEEE 802 will coordinate their work, via the

Finn, et al.               Expires May 3, 2018                 [Page 33]
Internet-Draft    Deterministic Networking Architecture     October 2017

   participation of common individuals, liaisons, and other means, to
   maximize the compatibility of their outputs.

   DetNet enabled end systems and intermediate nodes can be
   interconnected by sub-networks, i.e., Layer-2 technologies.  These
   sub-networks will provide DetNet compatible service for support of
   DetNet traffic.  Examples of sub-networks include 802.1TSN and a
   point-to-point OTN link.  Of course, multi-layer DetNet systems may
   be possible too, where one DetNet appears as a sub-network, and
   provides service to, a higher layer DetNet system.

5.  Security Considerations

   Security in the context of Deterministic Networking has an added
   dimension; the time of delivery of a packet can be just as important
   as the contents of the packet, itself.  A man-in-the-middle attack,
   for example, can impose, and then systematically adjust, additional
   delays into a link, and thus disrupt or subvert a real-time
   application without having to crack any encryption methods employed.
   See [RFC7384] for an exploration of this issue in a related context.

   Furthermore, in a control system where millions of dollars of
   equipment, or even human lives, can be lost if the DetNet QoS is not
   delivered, one must consider not only simple equipment failures,
   where the box or wire instantly becomes perfectly silent, but bizarre
   errors such as can be caused by software failures.  Because there is
   essential no limit to the kinds of failures that can occur,
   protecting against realistic equipment failures is indistinguishable,
   in most cases, from protecting against malicious behavior, whether
   accidental or intentional.  See also Section 3.3.2.

   Security must cover:

   o  the protection of the signaling protocol

   o  the authentication and authorization of the controlling systems

   o  the identification and shaping of the DetNet flows

6.  Privacy Considerations

   DetNet is provides a Quality of Service (QoS), and as such, does not
   directly raise any new privacy considerations.

   However, the requirement for every (or almost every) node along the
   path of a DetNet flow to identify DetNet flows may present an
   additional attack surface for privacy, should the DetNet paradigm be
   found useful in broader environments.

Finn, et al.               Expires May 3, 2018                 [Page 34]
Internet-Draft    Deterministic Networking Architecture     October 2017

7.  IANA Considerations

   This document does not require an action from IANA.

8.  Acknowledgements

   The authors wish to thank Jouni Korhonen, Erik Nordmark, George
   Swallow, Rudy Klecka, Anca Zamfir, David Black, Thomas Watteyne,
   Shitanshu Shah, Craig Gunther, Rodney Cummings, Balazs Varga,
   Wilfried Steiner, Marcel Kiessling, Karl Weber, Janos Farkas, Ethan
   Grossman, Pat Thaler, Lou Berger, and especially Michael Johas
   Teener, for their various contribution with this work.

9.  Access to IEEE 802.1 documents

   To access password protected IEEE 802.1 drafts, see the IETF IEEE
   802.1 information page at https://www.ietf.org/proceedings/52/slides/
   bridge-0/tsld003.htm.

10.  Informative References

   [AVnu]     http://www.avnu.org/, "The AVnu Alliance tests and
              certifies devices for interoperability, providing a simple
              and reliable networking solution for AV network
              implementation based on the Audio Video Bridging (AVB)
              standards.".

   [CCAMP]    IETF, "Common Control and Measurement Plane",
              <https://datatracker.ietf.org/doc/charter-ietf-ccamp/>.

   [HSR-PRP]  IEC, "High availability seamless redundancy (HSR) is a
              further development of the PRP approach, although HSR
              functions primarily as a protocol for creating media
              redundancy while PRP, as described in the previous
              section, creates network redundancy.  PRP and HSR are both
              described in the IEC 62439 3 standard.",
              <http://webstore.iec.ch/webstore/webstore.nsf/
              artnum/046615!opendocument>.

   [I-D.dt-detnet-dp-alt]
              Korhonen, J., Farkas, J., Mirsky, G., Thubert, P.,
              Zhuangyan, Z., and L. Berger, "DetNet Data Plane Protocol
              and Solution Alternatives", draft-dt-detnet-dp-alt-04
              (work in progress), September 2016.

Finn, et al.               Expires May 3, 2018                 [Page 35]
Internet-Draft    Deterministic Networking Architecture     October 2017

   [I-D.ietf-6tisch-architecture]
              Thubert, P., "An Architecture for IPv6 over the TSCH mode
              of IEEE 802.15.4", draft-ietf-6tisch-architecture-12 (work
              in progress), August 2017.

   [I-D.ietf-6tisch-tsch]
              Watteyne, T., Palattella, M., and L. Grieco, "Using
              IEEE802.15.4e TSCH in an IoT context: Overview, Problem
              Statement and Goals", draft-ietf-6tisch-tsch-06 (work in
              progress), March 2015.

   [I-D.ietf-detnet-problem-statement]
              Finn, N. and P. Thubert, "Deterministic Networking Problem
              Statement", draft-ietf-detnet-problem-statement-02 (work
              in progress), September 2017.

   [I-D.ietf-detnet-use-cases]
              Grossman, E., Gunther, C., Thubert, P., Wetterwald, P.,
              Raymond, J., Korhonen, J., Kaneko, Y., Das, S., Zha, Y.,
              Varga, B., Farkas, J., Goetz, F., Schmitt, J., Vilajosana,
              X., Mahmoodi, T., Spirou, S., Vizarreta, P., Huang, D.,
              Geng, X., Dujovne, D., and M. Seewald, "Deterministic
              Networking Use Cases", draft-ietf-detnet-use-cases-13
              (work in progress), September 2017.

   [I-D.ietf-roll-rpl-industrial-applicability]
              Phinney, T., Thubert, P., and R. Assimiti, "RPL
              applicability in industrial networks", draft-ietf-roll-
              rpl-industrial-applicability-02 (work in progress),
              October 2013.

   [I-D.svshah-tsvwg-deterministic-forwarding]
              Shah, S. and P. Thubert, "Deterministic Forwarding PHB",
              draft-svshah-tsvwg-deterministic-forwarding-04 (work in
              progress), August 2015.

   [I-D.varga-detnet-service-model]
              Varga, B. and J. Farkas, "DetNet Service Model", draft-
              varga-detnet-service-model-02 (work in progress), May
              2017.

   [IEEE802.1AS-2011]
              IEEE, "IEEE Std 802.1AS Timing and Synchronization for
              Time-Sensitive Applications in Bridged Local Area
              Networks", 2011,
              <http://ieeexplore.ieee.org/document/5741898/>.

Finn, et al.               Expires May 3, 2018                 [Page 36]
Internet-Draft    Deterministic Networking Architecture     October 2017

   [IEEE802.1BA-2011]
              IEEE, "IEEE Std 802.1BA Audio Video Bridging (AVB)
              Systems", 2011,
              <http://ieeexplore.ieee.org/document/6032690/>.

   [IEEE802.1CB]
              IEEE, "Frame Replication and Elimination for Reliability
              (IEEE Draft P802.1CB)", 2017,
              <http://www.ieee802.org/1/files/private/cb-drafts/>.

   [IEEE802.1Q-2014]
              IEEE, "IEEE Std 802.1Q Bridges and Bridged Networks",
              2014, <http://ieeexplore.ieee.org/document/6991462/>.

   [IEEE802.1Qbu]
              IEEE, "IEEEE Std 802.1Qbu Bridges and Bridged Networks -
              Amendment 26: Frame Preemption", 2016,
              <http://ieeexplore.ieee.org/document/7553415/>.

   [IEEE802.1Qbv]
              IEEE, "IEEEE Std 802.1Qbu Bridges and Bridged Networks -
              Amendment 25: Enhancements for Scheduled Traffic", 2015,
              <http://ieeexplore.ieee.org/document/7572858/>.

   [IEEE802.1Qca]
              IEEE, "IEEE Std 802.1Qca Bridges and Bridged Networks -
              Amendment 24: Path Control and Reservation", June 2015,
              <http://ieeexplore.ieee.org/document/7565435/>.

   [IEEE802.1Qcc]
              IEEE, "Stream Reservation Protocol (SRP) Enhancements and
              Performance Improvements (IEEE Draft P802.1Qcc)", 2017,
              <http://www.ieee802.org/1/files/private/cc-drafts/>.

   [IEEE802.1Qch]
              IEEE, "Cyclic Queuing and Forwarding (IEEE Draft
              P802.1Qch)", 2017,
              <http://www.ieee802.org/1/files/private/ch-drafts/>.

   [IEEE802.1TSNTG]
              IEEE Standards Association, "IEEE 802.1 Time-Sensitive
              Networks Task Group", 2013,
              <http://www.IEEE802.org/1/pages/avbridges.html>.

   [IEEE802.3-2015]
              IEEE, "IEEE Std 802.3 Standard for Ethernet", 2015,
              <http://ieeexplore.ieee.org/document/7428776/>.

Finn, et al.               Expires May 3, 2018                 [Page 37]
Internet-Draft    Deterministic Networking Architecture     October 2017

   [IEEE802.3br]
              IEEE, "IEEE Std 802.3br Standard for Ethernet Amendment 5:
              Specification and Management Parameters for Interspersing
              Express Traffic", 2016,
              <http://ieeexplore.ieee.org/document/7900321/>.

   [ISA95]    ANSI/ISA, "Enterprise-Control System Integration Part 1:
              Models and Terminology", 2000,
              <https://www.isa.org/isa95/>.

   [ODVA]     http://www.odva.org/, "The organization that supports
              network technologies built on the Common Industrial
              Protocol (CIP) including EtherNet/IP.".

   [PCE]      IETF, "Path Computation Element",
              <https://datatracker.ietf.org/doc/charter-ietf-pce/>.

   [Profinet]
              http://us.profinet.com/technology/profinet/, "PROFINET is
              a standard for industrial networking in automation.",
              <http://us.profinet.com/technology/profinet/>.

   [RFC2205]  Braden, R., Ed., Zhang, L., Berson, S., Herzog, S., and S.
              Jamin, "Resource ReSerVation Protocol (RSVP) -- Version 1
              Functional Specification", RFC 2205, DOI 10.17487/RFC2205,
              September 1997, <https://www.rfc-editor.org/info/rfc2205>.

   [RFC2475]  Blake, S., Black, D., Carlson, M., Davies, E., Wang, Z.,
              and W. Weiss, "An Architecture for Differentiated
              Services", RFC 2475, DOI 10.17487/RFC2475, December 1998,
              <https://www.rfc-editor.org/info/rfc2475>.

   [RFC3209]  Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
              and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
              Tunnels", RFC 3209, DOI 10.17487/RFC3209, December 2001,
              <https://www.rfc-editor.org/info/rfc3209>.

   [RFC3473]  Berger, L., Ed., "Generalized Multi-Protocol Label
              Switching (GMPLS) Signaling Resource ReserVation Protocol-
              Traffic Engineering (RSVP-TE) Extensions", RFC 3473,
              DOI 10.17487/RFC3473, January 2003,
              <https://www.rfc-editor.org/info/rfc3473>.

   [RFC3550]  Schulzrinne, H., Casner, S., Frederick, R., and V.
              Jacobson, "RTP: A Transport Protocol for Real-Time
              Applications", STD 64, RFC 3550, DOI 10.17487/RFC3550,
              July 2003, <https://www.rfc-editor.org/info/rfc3550>.

Finn, et al.               Expires May 3, 2018                 [Page 38]
Internet-Draft    Deterministic Networking Architecture     October 2017

   [RFC4203]  Kompella, K., Ed. and Y. Rekhter, Ed., "OSPF Extensions in
              Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 4203, DOI 10.17487/RFC4203, October 2005,
              <https://www.rfc-editor.org/info/rfc4203>.

   [RFC4655]  Farrel, A., Vasseur, J., and J. Ash, "A Path Computation
              Element (PCE)-Based Architecture", RFC 4655,
              DOI 10.17487/RFC4655, August 2006,
              <https://www.rfc-editor.org/info/rfc4655>.

   [RFC5307]  Kompella, K., Ed. and Y. Rekhter, Ed., "IS-IS Extensions
              in Support of Generalized Multi-Protocol Label Switching
              (GMPLS)", RFC 5307, DOI 10.17487/RFC5307, October 2008,
              <https://www.rfc-editor.org/info/rfc5307>.

   [RFC5316]  Chen, M., Zhang, R., and X. Duan, "ISIS Extensions in
              Support of Inter-Autonomous System (AS) MPLS and GMPLS
              Traffic Engineering", RFC 5316, DOI 10.17487/RFC5316,
              December 2008, <https://www.rfc-editor.org/info/rfc5316>.

   [RFC5392]  Chen, M., Zhang, R., and X. Duan, "OSPF Extensions in
              Support of Inter-Autonomous System (AS) MPLS and GMPLS
              Traffic Engineering", RFC 5392, DOI 10.17487/RFC5392,
              January 2009, <https://www.rfc-editor.org/info/rfc5392>.

   [RFC5673]  Pister, K., Ed., Thubert, P., Ed., Dwars, S., and T.
              Phinney, "Industrial Routing Requirements in Low-Power and
              Lossy Networks", RFC 5673, DOI 10.17487/RFC5673, October
              2009, <https://www.rfc-editor.org/info/rfc5673>.

   [RFC5921]  Bocci, M., Ed., Bryant, S., Ed., Frost, D., Ed., Levrau,
              L., and L. Berger, "A Framework for MPLS in Transport
              Networks", RFC 5921, DOI 10.17487/RFC5921, July 2010,
              <https://www.rfc-editor.org/info/rfc5921>.

   [RFC6372]  Sprecher, N., Ed. and A. Farrel, Ed., "MPLS Transport
              Profile (MPLS-TP) Survivability Framework", RFC 6372,
              DOI 10.17487/RFC6372, September 2011,
              <https://www.rfc-editor.org/info/rfc6372>.

   [RFC6658]  Bryant, S., Ed., Martini, L., Swallow, G., and A. Malis,
              "Packet Pseudowire Encapsulation over an MPLS PSN",
              RFC 6658, DOI 10.17487/RFC6658, July 2012,
              <https://www.rfc-editor.org/info/rfc6658>.

   [RFC7384]  Mizrahi, T., "Security Requirements of Time Protocols in
              Packet Switched Networks", RFC 7384, DOI 10.17487/RFC7384,
              October 2014, <https://www.rfc-editor.org/info/rfc7384>.

Finn, et al.               Expires May 3, 2018                 [Page 39]
Internet-Draft    Deterministic Networking Architecture     October 2017

   [RFC7426]  Haleplidis, E., Ed., Pentikousis, K., Ed., Denazis, S.,
              Hadi Salim, J., Meyer, D., and O. Koufopavlou, "Software-
              Defined Networking (SDN): Layers and Architecture
              Terminology", RFC 7426, DOI 10.17487/RFC7426, January
              2015, <https://www.rfc-editor.org/info/rfc7426>.

   [TEAS]     IETF, "Traffic Engineering Architecture and Signaling",
              <https://datatracker.ietf.org/doc/charter-ietf-teas/>.

Authors' Addresses

   Norman Finn
   Huawei Technologies Co. Ltd
   3755 Avocado Blvd.
   PMB 436
   La Mesa, California  91941
   US

   Phone: +1 925 980 6430
   Email: norman.finn@mail01.huawei.com

   Pascal Thubert
   Cisco Systems
   Village d'Entreprises Green Side
   400, Avenue de Roumanille
   Batiment T3
   Biot - Sophia Antipolis  06410
   FRANCE

   Phone: +33 4 97 23 26 34
   Email: pthubert@cisco.com

   Balazs Varga
   Ericsson
   Konyves Kalman krt. 11/B
   Budapest  1097
   Hungary

   Email: balazs.a.varga@ericsson.com

Finn, et al.               Expires May 3, 2018                 [Page 40]
Internet-Draft    Deterministic Networking Architecture     October 2017

   Janos Farkas
   Ericsson
   Konyves Kalman krt. 11/B
   Budapest  1097
   Hungary

   Email: janos.farkas@ericsson.com

Finn, et al.               Expires May 3, 2018                 [Page 41]