Skip to main content

A Per-Domain Path Computation Method for Establishing Inter-Domain Traffic Engineering (TE) Label Switched Paths (LSPs)
RFC 5152

Document Type RFC - Proposed Standard (February 2008)
Authors JP Vasseur , Raymond Zhang , Arthi Ayyangar
Last updated 2018-12-20
RFC stream Internet Engineering Task Force (IETF)
Formats
Additional resources Mailing list discussion
IESG Responsible AD Ross Callon
Send notices to (None)
RFC 5152
Networking Working Group                                JP. Vasseur, Ed.
Request for Comments: 5152                           Cisco Systems, Inc.
Category: Standards Track                               A. Ayyangar, Ed.
                                                        Juniper Networks
                                                                R. Zhang
                                                                      BT
                                                           February 2008

   A Per-Domain Path Computation Method for Establishing Inter-Domain
          Traffic Engineering (TE) Label Switched Paths (LSPs)

Status of This Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Abstract

   This document specifies a per-domain path computation technique for
   establishing inter-domain Traffic Engineering (TE) Multiprotocol
   Label Switching (MPLS) and Generalized MPLS (GMPLS) Label Switched
   Paths (LSPs).  In this document, a domain refers to a collection of
   network elements within a common sphere of address management or path
   computational responsibility such as Interior Gateway Protocol (IGP)
   areas and Autonomous Systems.

   Per-domain computation applies where the full path of an inter-domain
   TE LSP cannot be or is not determined at the ingress node of the TE
   LSP, and is not signaled across domain boundaries.  This is most
   likely to arise owing to TE visibility limitations.  The signaling
   message indicates the destination and nodes up to the next domain
   boundary.  It may also indicate further domain boundaries or domain
   identifiers.  The path through each domain, possibly including the
   choice of exit point from the domain, must be determined within the
   domain.

Vasseur, et al.             Standards Track                     [Page 1]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

Table of Contents

   1. Introduction ....................................................2
   2. Terminology .....................................................3
      2.1. Requirements Language ......................................4
   3. General Assumptions .............................................4
      3.1. Common Assumptions .........................................4
      3.2. Example of Topology for the Inter-Area TE Case .............6
      3.3. Example of Topology for the Inter-AS TE Case ...............7
   4. Per-Domain Path Computation Procedures ..........................8
      4.1. Example with an Inter-Area TE LSP .........................11
           4.1.1. Case 1: T0 Is a Contiguous TE LSP ..................11
           4.1.2. Case 2: T0 Is a Stitched or Nested TE LSP ..........12
      4.2. Example with an Inter-AS TE LSP ...........................13
           4.2.1. Case 1: T1 Is a Contiguous TE LSP ..................13
           4.2.2. Case 2: T1 Is a Stitched or Nested TE LSP ..........14
   5. Path Optimality/Diversity ......................................14
   6. Reoptimization of an Inter-Domain TE LSP .......................15
      6.1. Contiguous TE LSPs ........................................15
      6.2. Stitched or Nested (non-contiguous) TE LSPs ...............16
      6.3. Path Characteristics after Reoptimization .................17
   7. Security Considerations ........................................17
   8. Acknowledgements ...............................................18
   9. References .....................................................18
      9.1. Normative References ......................................18
      9.2. Informative References ....................................18

1.  Introduction

   The requirements for inter-domain Traffic Engineering (inter-area and
   inter-AS TE) have been developed by the Traffic Engineering Working
   Group and have been stated in [RFC4105] and [RFC4216].  The framework
   for inter-domain MPLS Traffic Engineering has been provided in
   [RFC4726].

   Some of the mechanisms used to establish and maintain inter-domain TE
   LSPs are specified in [RFC5151] and [RFC5150].

   This document exclusively focuses on the path computation aspects and
   defines a method for establishing inter-domain TE LSPs where each
   node in charge of computing a section of an inter-domain TE LSP path
   is always along the path of such a TE LSP.

   When the visibility of an end-to-end complete path spanning multiple
   domains is not available at the Head-end LSR (the LSR that initiated
   the TE LSP), one approach described in this document consists of
   using a per-domain path computation technique during LSP setup to
   determine the inter-domain TE LSP as it traverses multiple domains.

Vasseur, et al.             Standards Track                     [Page 2]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   The mechanisms proposed in this document are also applicable to MPLS
   TE domains other than IGP areas and ASs.

   The solution described in this document does not attempt to address
   all the requirements specified in [RFC4105] and [RFC4216].  This is
   acceptable according to [RFC4216], which indicates that a solution
   may be developed to address a particular deployment scenario and
   might, therefore, not meet all requirements for other deployment
   scenarios.

   It must be pointed out that the inter-domain path computation
   technique proposed in this document is one among many others.  The
   choice of the appropriate technique must be driven by the set of
   requirements for the path attributes and the applicability to a
   particular technique with respect to the deployment scenario.  For
   example, if the requirement is to get an end-to-end constraint-based
   shortest path across multiple domains, then a mechanism using one or
   more distributed PCEs could be used to compute the shortest path
   across different domains (see [RFC4655]).  Other off-line mechanisms
   for path computation are not precluded either.  Note also that a
   Service Provider may elect to use different inter-domain path
   computation techniques for different TE LSP types.

2.  Terminology

   Terminology used in this document:

   AS: Autonomous System.

   ABR: Area Border Router, a router used to connect two IGP areas
   (areas in OSPF or levels in Intermediate System to Intermediate
   System (IS-IS)).

   ASBR: Autonomous System Border Router, a router used to connect
   together ASs of a different or the same Service Provider via one or
   more inter-AS links.

   Boundary LSR: A boundary LSR is either an ABR in the context of
   inter-area TE or an ASBR in the context of inter-AS TE.

   ERO: Explicit Route Object.

   IGP: Interior Gateway Protocol.

   Inter-AS TE LSP: A TE LSP that crosses an AS boundary.

   Inter-area TE LSP: A TE LSP that crosses an IGP area.

Vasseur, et al.             Standards Track                     [Page 3]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   LSR: Label Switching Router.

   LSP: Label Switched Path.

   TE LSP: Traffic Engineering Label Switched Path.

   PCE: Path Computation Element, an entity (component, application, or
   network node) that is capable of computing a network path or route
   based on a network graph and applying computational constraints.

   TED: Traffic Engineering Database.

   The notion of contiguous, stitched, and nested TE LSPs is defined in
   [RFC4726] and will not be repeated here.

2.1.  Requirements Language

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in RFC 2119 [RFC2119].

3.  General Assumptions

3.1.  Common Assumptions

   - Each domain in all the examples below is assumed to be capable of
     doing Traffic Engineering (i.e., running OSPF-TE or ISIS-TE and
     RSVP-TE (Resource Reservation Protocol Traffic Engineering)).  A
     domain may itself comprise multiple other domains, e.g., an AS may
     itself be composed of several other sub-ASs (BGP confederations) or
     areas/levels.  In this case, the path computation technique
     described for inter-area and inter-AS MPLS Traffic Engineering
     applies recursively.

   - The inter-domain TE LSPs are signaled using RSVP-TE ([RFC3209] and
     [RFC3473]).

   - The path (specified by an ERO (Explicit Route Object) in an RSVP-TE
     Path message) for an inter-domain TE LSP may be signaled as a set
     of (loose and/or strict) hops.

   - The hops may identify:

      * The complete strict path end-to-end across different domains

      * The complete strict path in the source domain followed by
         boundary LSRs (or domain identifiers, e.g., AS numbers)

Vasseur, et al.             Standards Track                     [Page 4]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

      * The complete list of boundary LSRs along the path

      * The current boundary LSR and the LSP destination

   The set of (loose or strict) hops can be either statically configured
   on the Head-end LSR or dynamically computed.  A per-domain path
   computation method is defined in this document with an optional
   auto-discovery mechanism (e.g., based on IGP, BGP, policy routing
   information) yielding the next-hop boundary node (domain exit point,
   such as an Area Border Router (ABR) or an Autonomous System Border
   Router (ASBR)) along the path as the TE LSP is being signaled, along
   with potential crankback mechanisms.  Alternatively, the domain exit
   points may be statically configured on the Head-end LSR, in which
   case next-hop boundary node auto-discovery would not be required.

   - Boundary LSRs are assumed to be capable of performing local path
     computation for expansion of a loose next hop in the signaled ERO
     if the path is not signaled by the Head-end LSR as a set of strict
     hops or if the strict hop is an abstract node (e.g., an AS).  In
     any case, no topology or resource information needs to be
     distributed between domains (as mandated per [RFC4105] and
     [RFC4216]), which is critical to preserve IGP/BGP scalability and
     confidentiality in the case of TE LSPs spanning multiple routing
     domains.

   - The paths for the intra-domain Hierarchical LSP (H-LSP) or Stitched
     LSP (S-LSP) or for a contiguous TE LSP within the domain may be
     pre-configured or computed dynamically based on the arriving
     inter-domain LSP setup request (depending on the requirements of
     the transit domain).  Note that this capability is explicitly
     specified as a requirement in [RFC4216].  When the paths for the
     H-LSP/S-LSP are pre-configured, the constraints as well as other
     parameters like a local protection scheme for the intra-domain H-
     LSP/S-LSP are also pre-configured.

   - While certain constraints like bandwidth can be used across
     different domains, certain other TE constraints like resource
     affinity, color, metric, etc. as listed in [RFC2702] may need to be
     translated at domain boundaries.  If required, it is assumed that,
     at the domain boundary LSRs, there will exist some sort of local
     mapping based on policy agreement in order to translate such
     constraints across domain boundaries.  It is expected that such an
     assumption particularly applies to inter-AS TE: for example, the
     local mapping would be similar to the inter-AS TE agreement
     enforcement polices stated in [RFC4216].

Vasseur, et al.             Standards Track                     [Page 5]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   - The procedures defined in this document are applicable to any node
     (not just a boundary node) that receives a Path message with an ERO
     that constrains a loose hop or an abstract node that is not a
     simple abstract node (that is, an abstract node that identifies
     more than one LSR).

3.2.  Example of Topology for the Inter-Area TE Case

   The following example will be used for the inter-area TE case in this
   document.

                <-area 1-><-- area 0 --><--- area 2 --->
                ------ABR1------------ABR3-------
                |    /   |              |  \     |
               R0--X1    |              |   X2---X3--R1
                |        |              |  /     |
                ------ABR2-----------ABR4--------
               <=========== Inter-area TE LSP =======>

         Figure 1 - Example of topology for the inter-area TE case

   Description of Figure 1:

   - ABR1, ABR2, ABR3, and ABR4 are ABRs.
   - X1 is an LSR in area 1.
   - X2 and X3 are LSRs in area 2.
   - An inter-area TE LSP T0 originated at R0 in area 1 and terminated
     at R1 in area 2.

   Notes:

   - The terminology used in the example above corresponds to OSPF, but
     the path computation technique proposed in this document equally
     applies to the case of an IS-IS multi-level network.

   - Just a few routers in each area are depicted in the diagram above
     for the sake of simplicity.

   - The example depicted in Figure 1 shows the case where the Head-end
     and Tail-end areas are connected by means of area 0.  The case of
     an inter-area TE LSP between two IGP areas that does not transit
     through area 0 is not precluded.

Vasseur, et al.             Standards Track                     [Page 6]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

3.3.  Example of Topology for the Inter-AS TE Case

   We consider the following general case, built on a superset of the
   various scenarios defined in [RFC4216]:

            <-- AS1 ----> <------- AS2 ------><--- AS3 ----->

                     <---BGP--->            <---BGP-->
      CE1---R0---X1-ASBR1-----ASBR4--R3---ASBR7----ASBR9----R6
            |\     \ |       / |   / |   / |          |      |
            | \     ASBR2---/ ASBR5  | --  |          |      |
            |  \     |         |     |/    |          |      |
            R1-R2---ASBR3-----ASBR6--R4---ASBR8----ASBR10---R7---CE2

            <======= Inter-AS TE LSP (LSR to LSR)===========>
      or

      <======== Inter-AS TE LSP (CE to ASBR) =>

      or

      <================= Inter-AS TE LSP (CE to CE)===============>

         Figure 2 - Example of topology for the inter-AS TE case

   The diagram depicted in Figure 2 covers all the inter-AS TE
   deployment cases described in [RFC4216].

   Description of Figure 2:

   - Three interconnected ASs, respectively AS1, AS2, and AS3.  Note
     that in some scenarios described in [RFC4216] AS1=AS3.

   - The ASBRs in different ASs are BGP peers.  There is usually no IGP
     running on the single hop links interconnecting the ASBRs and also
     referred to as inter-ASBR links.

   - Each AS runs an IGP (IS-IS or OSPF) with the required IGP TE
     extensions (see [RFC3630], [RFC3784], [RFC4203] and [RFC4205]).  In
     other words, the ASs are TE enabled.

   - CE: Customer Edge router.

   - Each AS can be made of several IGP areas.  The path computation
     technique described in this document applies to the case of a
     single AS made of multiple IGP areas, multiple ASs made of a single
     IGP area, or any combination of the above.  For the sake of
     simplicity, each routing domain will be considered as a single area

Vasseur, et al.             Standards Track                     [Page 7]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

     in this document.  The case of an inter-AS TE LSP spanning multiple
     ASs where some of those ASs are themselves made of multiple IGP
     areas can be easily derived from the examples above: the per-domain
     path computation technique described in this document is applied
     recursively in this case.

   - An inter-AS TE LSP T1 originated at R0 in AS1 and terminated at R6
     in AS3.

4.  Per-Domain Path Computation Procedures

   The mechanisms for inter-domain TE LSP computation as described in
   this document can be used regardless of the nature of the
   inter-domain TE LSP (contiguous, stitched, or nested).

   Note that any path can be defined as a set of loose and strict hops.
   In other words, in some cases, it might be desirable to rely on the
   dynamic path computation in some domains, and exert a strict control
   on the path in other domains (defining strict hops).

   When an LSR that is a boundary node such as an ABR/ASBR receives a
   Path message with an ERO that contains a strict node, the procedures
   specified in [RFC3209] apply and no further action is needed.

   When an LSR that is a boundary node such as an ABR/ASBR receives a
   Path message with an ERO that contains a loose hop or an abstract
   node that is not a simple abstract node (that is, an abstract node
   that identifies more than one LSR), then it MUST follow the
   procedures as described in [RFC5151].

   In addition, the following procedures describe the path computation
   procedures that SHOULD be carried out on the LSR:

   1) If the next hop is not present in the TED, the two following
      conditions MUST be checked:

      o  Whether the IP address of the next-hop boundary LSR is outside
         of the current domain

      o  Whether the next-hop domain is PSC (Packet Switch Capable) and
         uses in-band control channel

   If the two conditions above are satisfied, then the boundary LSR
   SHOULD check if the next hop has IP reachability (via IGP or BGP).
   If the next hop is not reachable, then a signaling failure occurs and
   the LSR SHOULD send back an RSVP PathErr message upstream with error
   code=24 ("Routing Problem") and error subcode as described in section
   4.3.4 of [RFC3209].  If the available routing information indicates

Vasseur, et al.             Standards Track                     [Page 8]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   that next hop is reachable, the selected route will be expected to
   pass through a domain boundary via a domain boundary LSR.  The
   determination of domain boundary point based on routing information
   is what we term as "auto-discovery" in this document.  In the absence
   of such an auto-discovery mechanism, a) the ABR in the case of
   inter-area TE or the ASBR in the next-hop AS in the case of inter-AS
   TE should be the signaled loose next hop in the ERO and hence should
   be accessible via the TED, or b) there needs to be an alternate
   scheme that provides the domain exit points.  Otherwise, the path
   computation for the inter-domain TE LSP will fail.

   An implementation MAY support the ability to disable such an IP
   reachability fall-back option should the next-hop boundary LSR not be
   present in the TED.  In other words, an implementation MAY support
   the possibility to trigger a signaling failure whenever the next hop
   is not present in the TED.

   2) Once the next-hop boundary LSR has been determined (according to
      the procedure described in 1)) or if the next-hop boundary is
      present in the TED:

      o  Case of a contiguous TE LSP.  Unless not allowed by policy, the
         boundary LSR that processes the ERO SHOULD perform an ERO
         expansion (a process consisting of computing the constrained
         path up to the next loose hop and adding the list of hops as
         strict nodes in the ERO).  If no path satisfying the set of
         constraints can be found, then this is treated as a path
         computation and signaling failure and an RSVP PathErr message
         SHOULD be sent for the inter-domain TE LSP based on section
         4.3.4 of [RFC3209].

      o  Case of a stitched or nested TE LSP

         *  If the boundary LSR is a candidate LSR for intra-area H-LSP/
            S-LSP setup (the boundary has local policy for nesting or
            stitching), the TE LSP is a candidate for hierarchy/nesting
            (the "Contiguous LSP" bit defined in [RFC5151] is not set),
            and if there is no H-LSP/S-LSP from this LSR to the next-hop
            boundary LSR that satisfies the constraints, it SHOULD
            signal an H-LSP/S-LSP to the next-hop boundary LSR.  If a
            pre-configured H-LSP(s) or S-LSP(s) already exists, then it
            will try to select from among those intra-domain LSPs.
            Depending on local policy, it MAY signal a new H-LSP/S-LSP
            if this selection fails.  If the H-LSP/S-LSP is successfully
            signaled or selected, it propagates the inter-domain Path
            message to the next hop following the procedures described
            in [RFC5151].  If for some reason the dynamic H-LSP/S-LSP
            setup to the next-hop boundary LSR fails, then this SHOULD

Vasseur, et al.             Standards Track                     [Page 9]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

            be treated as a path computation and signaling failure and
            an RSVP PathErr message SHOULD be sent upstream for the
            inter-domain LSP.  Similarly, if selection of a pre-
            configured H-LSP/S-LSP fails and local policy prevents
            dynamic H-LSP/S, this SHOULD be treated as a path
            computation and signaling failure and an RSVP PathErr
            message SHOULD be sent upstream for the inter-domain TE LSP.
            In both of these cases, procedures described in section
            4.3.4 of [RFC3209] SHOULD be followed to handle the failure.

         *  If, however, the boundary LSR is not a candidate for
            intra-domain H-LSP/S-LSP (the boundary LSR does not have
            local policy for nesting or stitching) or the TE LSP is not
            a candidate for hierarchy/nesting (the "Contiguous LSP" bit
            defined in [RFC5151] is set), then it SHOULD apply the same
            procedure as for the contiguous case.

   The ERO of an inter-domain TE LSP may comprise abstract nodes such as
   ASs.  In such a case, upon receiving the ERO whose next hop is an AS,
   the boundary LSR has to determine the next-hop boundary LSR, which
   may be determined based on the auto-discovery process mentioned
   above.  If multiple ASBR candidates exist, the boundary LSR may apply
   some policies based on peering contracts that may have been
   pre-negotiated.  Once the next-hop boundary LSR has been determined,
   a similar procedure as the one described above is followed.

   Note the following related to the inter-AS TE case:

   In terms of computation of an inter-AS TE LSP path, an interesting
   optimization technique consists of allowing the ASBRs to flood the TE
   information related to the inter-ASBR link(s) although no IGP TE is
   enabled over those links (and so there is no IGP adjacency over the
   inter-ASBR links).  This of course implies that the inter-ASBR links
   be TE-enabled although no IGP is running on those links.

            <-- AS1 ----> <------- AS2 ------><--- AS3 ----->

                     <---BGP--->            <---BGP-->
      CE1---R0---X1-ASBR1-----ASBR4--R3---ASBR7----ASBR9----R6
            |\     \ |       / |   / |   / |          |      |
            | \     ASBR2---/ ASBR5  | --  |          |      |
            |  \     |         |     |/    |          |      |
            R1-R2---ASBR3-----ASBR6--R4---ASBR8----ASBR10---R7---CE2

      Figure 3 - Flooding of the TE-related information for
                 the inter-ASBR links

Vasseur, et al.             Standards Track                    [Page 10]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   Referring to Figure 3, ASBR1 for example would advertise in its OSPF
   Link State Advertisement (LSA)/IS-IS LSP the Traffic Engineering TLVs
   related to the link ASBR1-ASBR4.

   This allows an LSR (could be the entry ASBR) in the previous AS to
   make a more appropriate route selection up to the entry ASBR in the
   immediately downstream AS taking into account the constraints
   associated with the inter-ASBR links.  This reduces the risk of call
   setup failure due to inter-ASBR links not satisfying the inter-AS TE
   LSP set of constraints.  Note that the TE information is only related
   to the inter-ASBR links: the TE LSA/LSP flooded by the ASBR includes
   not only the TE-enabled links contained in the AS but also the
   inter-ASBR links.

   Note that no summarized TE information is leaked between ASs, which
   is compliant with the requirements listed in [RFC4105] and [RFC4216].

   For example, consider the diagram depicted in Figure 2: when ASBR1
   floods its IGP TE LSA ((opaque LSA for OSPF)/LSP (TLV 22 for IS-IS))
   in its routing domain, it reflects the reservation states and TE
   properties of the following links: X1-ASBR1, ASBR1-ASBR2, and
   ASBR1-ASBR4.

   Thanks to such an optimization, the inter-ASBR TE link information
   corresponding to the links originated by the ASBR is made available
   in the TED of other LSRs in the same domain to which the ASBR
   belongs.  Consequently, the path computation for an inter-AS TE LSP
   path can also take into account the inter-ASBR link(s).  This will
   improve the chance of successful signaling along the next AS in case
   of resource shortage or unsatisfied constraints on inter-ASBR links,
   and it potentially reduces one level of crankback.  Note that no
   topology information is flooded, and these links are not used in IGP
   SPF computations.  Only the TE information for the outgoing links
   directly connected to the ASBR is advertised.

   Note that an operator may decide to operate a stitched segment or
   1-hop hierarchical LSP for the inter-ASBR link.

4.1.  Example with an Inter-Area TE LSP

   The following example uses Figure 1 as a reference.

4.1.1.  Case 1: T0 Is a Contiguous TE LSP

   The Head-end LSR (R0) first determines the next-hop ABR (which could
   be manually configured by the user or dynamically determined by using
   the auto-discovery mechanism).  R0 then computes the path to reach
   the selected next-hop ABR (ABR1) and signals the Path message.  When

Vasseur, et al.             Standards Track                    [Page 11]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   the Path message reaches ABR1, it first determines the next-hop ABR
   from its area 0 along the LSP path (say, ABR3), either directly from
   the ERO (if for example the next-hop ABR is specified as a loose hop
   in the ERO) or by using the auto-discovery mechanism specified above.

   - Example 1 (set of loose hops):
     R0-ABR1(loose)-ABR3(loose)-R1(loose)

   - Example 2 (mix of strict and loose hops):
     R0-X1-ABR1-ABR3(loose)-X2-X3-R1

   Note that a set of paths can be configured on the Head-end LSR,
   ordered by priority.  Each priority path can be associated with a
   different set of constraints.  It may be desirable to systematically
   have a last-resort option with no constraint to ensure that the
   inter-area TE LSP could always be set up if at least a TE path exists
   between the inter-area TE LSP source and destination.  In case of
   setup failure or when an RSVP PathErr is received indicating that the
   TE LSP has suffered a failure, an implementation might support the
   possibility of retrying a particular path option a configurable
   amount of times (optionally with dynamic intervals between each
   trial) before trying a lower-priority path option.

   Once it has computed the path up to the next-hop ABR (ABR3), ABR1
   sends the Path message along the computed path.  Upon receiving the
   Path message, ABR3 then repeats a similar procedure.  If ABR3 cannot
   find a path obeying the set of constraints for the inter-area TE LSP,
   the signaling process stops and ABR3 sends a PathErr message to ABR1.
   Then ABR1 can in turn trigger a new path computation by selecting
   another egress boundary LSR (ABR4 in the example above) if crankback
   is allowed for this inter-area TE LSP (see [RFC4920]).  If crankback
   is not allowed for that inter-area TE LSP or if ABR1 has been
   configured not to perform crankback, then ABR1 MUST stop the
   signaling process and MUST forward a PathErr up to the Head-end LSR
   (R0) without trying to select another ABR.

4.1.2.  Case 2: T0 Is a Stitched or Nested TE LSP

   The Head-end LSR (R0) first determines the next-hop ABR (which could
   be manually configured by the user or dynamically determined by using
   the auto-discovery mechanism).  R0 then computes the path to reach
   the selected next-hop ABR and signals the Path message.  When the
   Path message reaches ABR1, it first determines the next-hop ABR from
   its area 0 along the LSP path (say ABR3), either directly from the
   ERO (if for example the next-hop ABR is specified as a loose hop in
   the ERO) or by using an auto-discovery mechanism, specified above.

Vasseur, et al.             Standards Track                    [Page 12]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   ABR1 then checks whether it has an H-LSP or S-LSP to ABR3 matching
   the constraints carried in the inter-area TE LSP Path message.  If
   not, ABR1 computes the path for an H-LSP or S-LSP from ABR1 to ABR3
   satisfying the constraint and sets it up accordingly.  Note that the
   H-LSP or S-LSP could have also been pre-configured.

   Once ABR1 has selected the H-LSP/S-LSP for the inter-area LSP, using
   the signaling procedures described in [RFC5151], ABR1 sends the Path
   message for the inter-area TE LSP to ABR3.  Note that irrespective of
   whether ABR1 does nesting or stitching, the Path message for the
   inter-area TE LSP is always forwarded to ABR3.  ABR3 then repeats the
   exact same procedures.  If ABR3 cannot find a path obeying the set of
   constraints for the inter-area TE LSP, ABR3 sends a PathErr message
   to ABR1.  Then ABR1 can in turn either select another H-LSP/S-LSP to
   ABR3 if such an LSP exists or select another egress boundary LSR
   (ABR4 in the example above) if crankback is allowed for this inter-
   area TE LSP (see [RFC4920]).  If crankback is not allowed for that
   inter-area TE LSP or if ABR1 has been configured not to perform
   crankback, then ABR1 forwards the PathErr up to the inter-area Head-
   end LSR (R0) without trying to select another egress LSR.

4.2.  Example with an Inter-AS TE LSP

   The following example uses Figure 2 as a reference.

   The path computation procedures for establishing an inter-AS TE LSP
   are very similar to those of an inter-area TE LSP described above.
   The main difference is related to the presence of inter-ASBR link(s).

4.2.1.  Case 1: T1 Is a Contiguous TE LSP

   The inter-AS TE path may be configured on the Head-end LSR as a set
   of strict hops, loose hops, or a combination of both.

   - Example 1 (set of loose hops):
     ASBR4(loose)-ASBR9(loose)-R6(loose)

   - Example 2 (mix of strict and loose hops):
     R2-ASBR3-ASBR2-ASBR1-ASBR4-ASBR10(loose)-ASBR9-R6

   In example 1 above, a per-AS path computation is performed,
   respectively on R0 for AS1, ASBR4 for AS2, and ASBR9 for AS3.  Note
   that when an LSR has to perform an ERO expansion, the next hop either
   must belong to the same AS or must be the ASBR directly connected to
   the next hop AS.  In this latter case, the ASBR reachability is
   announced in the IGP TE LSA/LSP originated by its neighboring ASBR.
   In example 1 above, the TE LSP path is defined as: ASBR4(loose)-
   ASBR9(loose)-R6(loose).  This implies that R0 must compute the path

Vasseur, et al.             Standards Track                    [Page 13]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   from R0 to ASBR4, hence the need for R0 to get the TE reservation
   state related to the ASBR1-ASBR4 link (flooded in AS1 by ASBR1).  In
   addition, ASBR1 must also announce the IP address of ASBR4 specified
   in T1's path configuration.

   Once it has computed the path up to the next-hop ASBR, ASBR1 sends
   the Path message for the inter-area TE LSP to ASBR4 (supposing that
   ASBR4 is the selected next-hop ASBR).  ASBR4 then repeats the exact
   same procedures.  If ASBR4 cannot find a path obeying the set of
   constraints for the inter-AS TE LSP, then ASBR4 sends a PathErr
   message to ASBR1.  Then ASBR1 can in turn either select another ASBR
   (ASBR5 in the example above) if crankback is allowed for this inter-
   AS TE LSP (see [RFC4920]), or if crankback is not allowed for that
   inter-AS TE LSP or if ASBR1 has been configured not to perform
   crankback, ABR1 stops the signaling process and forwards a PathErr up
   to the Head-end LSR (R0) without trying to select another egress LSR.
   In this case, the Head-end LSR can in turn select another sequence of
   loose hops, if configured.  Alternatively, the Head-end LSR may
   decide to retry the same path; this can be useful in case of setup
   failure due to an outdated IGP TE database in some downstream AS.  An
   alternative could also be for the Head-end LSR to retry the same
   sequence of loose hops after having relaxed some constraint(s).

4.2.2.  Case 2: T1 Is a Stitched or Nested TE LSP

   The path computation procedures are very similar to the inter-area
   LSP setup case described earlier.  In this case, the H-LSPs or S-LSPs
   are originated by the ASBRs at the entry to the AS.

5.  Path Optimality/Diversity

   Since the inter-domain TE LSP is computed on a per-domain (area, AS)
   basis, one cannot guarantee that the optimal inter-domain path can be
   found.

   Moreover, computing two diverse paths using a per-domain path
   computation approach may not be possible in some topologies (due to
   the well-known "trapping" problem).

   For example, consider the following simple topology:

                            +-------+
                           /         \
                          A----B-----C------D
                               \           /
                                +---------+

                Figure 4 - Example of the "trapping" problem

Vasseur, et al.             Standards Track                    [Page 14]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   In the simple topology depicted in Figure 4, with a serialized
   approach using the per-domain path computation technique specified in
   this document, a first TE LSP may be computed following the path
   A-B-C-D, in which case no diverse path could be found although two
   diverse paths actually exist: A-C-D and A-B-D.  The aim of that
   simple example that can easily be extended to the inter-domain case
   is to illustrate the potential issue of not being able to find
   diverse paths using the per-domain path computation approach when
   diverse paths exist.

   As already pointed out, the required path computation method can be
   selected by the Service Provider on a per-LSP basis.

   If the per-domain path computation technique does not meet the set of
   requirements for a particular TE LSP (e.g., path optimality,
   requirements for a set of diversely routed TE LSPs), other techniques
   such as PCE-based path computation techniques may be used (see
   [RFC4655]).

6.  Reoptimization of an Inter-Domain TE LSP

   As stated in [RFC4216] and [RFC4105], the ability to reoptimize an
   already established inter-domain TE LSP constitutes a requirement.
   The reoptimization process significantly differs based upon the
   nature of the TE LSP and the mechanism in use for the TE LSP
   computation.

   The following mechanisms can be used for reoptimization and are
   dependent on the nature of the inter-domain TE LSP.

6.1.  Contiguous TE LSPs

   After an inter-domain TE LSP has been set up, a better route might
   appear within any traversed domain.  Then in this case, it is
   desirable to get the ability to reroute an inter-domain TE LSP in a
   non-disruptive fashion (making use of the so-called Make-Before-Break
   procedure) to follow a better path.  This is a known as a TE LSP
   reoptimization procedure.

   [RFC4736] proposes a mechanism that allows the Head-end LSR to be
   notified of the existence of a more optimal path in a downstream
   domain.  The Head-end LSR may then decide to gracefully reroute the
   TE LSP using the Make-Before-Break procedure.  In case of a
   contiguous LSP, the reoptimization process is strictly controlled by
   the Head-end LSR that triggers the Make-Before-Break procedure as
   defined in [RFC3209], regardless of the location of the better path.

Vasseur, et al.             Standards Track                    [Page 15]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

6.2.  Stitched or Nested (non-contiguous) TE LSPs

   In the case of a stitched or nested inter-domain TE LSP, the
   reoptimization process is treated as a local matter to any domain.
   The main reason is that the inter-domain TE LSP is a different LSP
   (and therefore different RSVP session) from the intra-domain S-LSP or
   H-LSP in an area or an AS.  Therefore, reoptimization in a domain is
   done by locally reoptimizing the intra-domain H-LSP or S-LSP.  Since
   the inter-domain TE LSPs are transported using S-LSP or H-LSP across
   each domain, optimality of the inter-domain TE LSP in a domain is
   dependent on the optimality of the corresponding S-LSP or H-LSP.  If
   after an inter-domain LSP is set up a more optimal path is available
   within a domain, the corresponding S-LSP or H-LSP will be reoptimized
   using Make-Before-Break techniques discussed in [RFC3209].
   Reoptimization of the H-LSP or S-LSP automatically reoptimizes the
   inter-domain TE LSPs that the H-LSP or S-LSP transports.
   Reoptimization parameters like frequency of reoptimization, criteria
   for reoptimization like metric or bandwidth availability, etc. can
   vary from one domain to another and can be configured as required,
   per intra-domain TE S-LSP or H-LSP if it is pre-configured or based
   on some global policy within the domain.

   Hence, in this scheme, since each domain takes care of reoptimizing
   its own S-LSPs or H-LSPs, and therefore the corresponding
   inter-domain TE LSPs, the Make-Before-Break can happen locally and is
   not triggered by the Head-end LSR for the inter-domain LSP.  So, no
   additional RSVP signaling is required for LSP reoptimization, and
   reoptimization is transparent to the Head-end LSR of the inter-domain
   TE LSP.

   If, however, an operator desires to manually trigger reoptimization
   at the Head-end LSR for the inter-domain TE LSP, then this solution
   does not prevent that.  A manual trigger for reoptimization at the
   Head-end LSR SHOULD force a reoptimization thereby signaling a "new"
   path for the same LSP (along the more optimal path) making use of the
   Make-Before-Break procedure.  In response to this new setup request,
   the boundary LSR either may initiate new S-LSP setup, in case the
   inter-domain TE LSP is being stitched to the intra-domain S-LSP, or
   it may select an existing or new H-LSP, in case of nesting.  When the
   LSP setup along the current path is complete, the Head-end LSR should
   switch over the traffic onto that path, and the old path is
   eventually torn down.  Note that the Head-end LSR does not know a
   priori whether a more optimal path exists.  Such a manual trigger
   from the Head-end LSR of the inter-domain TE LSP is, however, not
   considered to be a frequent occurrence.

Vasseur, et al.             Standards Track                    [Page 16]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   Procedures described in [RFC4736] MUST be used if the operator does
   not desire local reoptimization of certain inter-domain LSPs.  In
   this case, any reoptimization event within the domain MUST be
   reported to the Head-end node.  This SHOULD be a configurable policy.

6.3.  Path Characteristics after Reoptimization

   Note that in the case of loose hop reoptimization of contiguous
   inter-domain TE LSP or local reoptimization of stitched/nested S-LSP
   where boundary LSRs are specified as loose hops, the TE LSP may
   follow a preferable path within one or more domain(s) but would still
   traverse the same set of boundary LSRs.  In contrast, in the case of
   PCE-based path computation techniques, because the end-to-end optimal
   path is computed, the reoptimization process may lead to following a
   completely different inter-domain path (including a different set of
   boundary LSRs).

7.  Security Considerations

   Signaling of inter-domain TE LSPs raises security issues (discussed
   in section 7 of [RFC5151]).

   [RFC4726] provides an overview of the requirements for security in an
   MPLS-TE or GMPLS multi-domain environment.  In particular, when
   signaling an inter-domain RSVP-TE LSP, an operator may make use of
   the security features already defined for RSVP-TE ([RFC3209]).  This
   may require some coordination between the domains to share the keys
   (see [RFC2747] and [RFC3097]), and care is required to ensure that
   the keys are changed sufficiently frequently.  Note that this may
   involve additional synchronization, should the domain border nodes be
   protected with Fast Reroute ([RFC4090], since the Merge Point (MP)
   and Point of Local Repair (PLR) should also share the key.  For an
   inter-domain TE LSP, especially when it traverses different
   administrative or trust domains, the following mechanisms SHOULD be
   provided to an operator (also see [RFC4216]):

   1) A way to enforce policies and filters at the domain borders to
      process the incoming inter-domain TE LSP setup requests (Path
      messages) based on certain agreed trust and service
      levels/contracts between domains.  Various LSP attributes such as
      bandwidth, priority, etc. could be part of such a contract.

   2) A way for the operator to rate-limit LSP setup requests or error
      notifications from a particular domain.

   3) A mechanism to allow policy-based outbound RSVP message processing
      at the domain border node, which may involve filtering or
      modification of certain addresses in RSVP objects and messages.

Vasseur, et al.             Standards Track                    [Page 17]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   This document relates to inter-domain path computation.  It must be
   noted that the process for establishing paths described in this
   document does not increase the information exchanged between ASs and
   preserves topology confidentiality, in compliance with [RFC4105] and
   [RFC4216].  That being said, the signaling of inter-domain TE LSP
   according to the procedure defined in this document requires path
   computation on boundary nodes that may be exposed to various attacks.
   Thus, it is RECOMMENDED to support policy decisions to reject the ERO
   expansion of an inter-domain TE LSP if not allowed.

8.  Acknowledgements

   We would like to acknowledge input and helpful comments from Adrian
   Farrel, Jean-Louis Le Roux, Dimitri Papadimitriou, and Faisal Aslam.

9.  References

9.1.  Normative References

   [RFC2119]   Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.

   [RFC3209]   Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V.,
               and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP
               Tunnels", RFC 3209, December 2001.

   [RFC3473]   Berger, L., Ed., "Generalized Multi-Protocol Label
               Switching (GMPLS) Signaling Resource ReserVation
               Protocol-Traffic Engineering (RSVP-TE) Extensions", RFC
               3473, January 2003.

9.2.  Informative References

   [RFC4920]   Farrel, A., Ed., Satyanarayana, A., Iwata, A., Fujita,
               N., and G. Ash, "Crankback Signaling Extensions for MPLS
               and GMPLS RSVP-TE", RFC 4920, July 2007.

   [RFC5151]   Farrel, A., Ed., Ayyangar, A., and JP. Vasseur, "Inter-
               Domain MPLS and GMPLS Traffic Engineering -- Resource
               Reservation Protocol-Traffic Engineering (RSVP-TE)
               Extensions", RFC 5151, February 2008.

   [RFC5150]   Ayyangar, A., Kompella, K., Vasseur, JP., and A. Farrel,
               "Label Switched Path Stitching with Generalized
               Multiprotocol Label Switching Traffic Engineering (GMPLS
               TE)", RFC 5150, February 2008.

Vasseur, et al.             Standards Track                    [Page 18]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   [RFC2702]   Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J.
               McManus, "Requirements for Traffic Engineering Over
               MPLS", RFC 2702, September 1999.

   [RFC2747]   Baker, F., Lindell, B., and M. Talwar, "RSVP
               Cryptographic Authentication", RFC 2747, January 2000.

   [RFC3097]   Braden, R. and L. Zhang, "RSVP Cryptographic
               Authentication -- Updated Message Type Value", RFC 3097,
               April 2001.

   [RFC3630]   Katz, D., Kompella, K., and D. Yeung, "Traffic
               Engineering (TE) Extensions to OSPF Version 2", RFC 3630,
               September 2003.

   [RFC3784]   Smit, H. and T. Li, "Intermediate System to Intermediate
               System (IS-IS) Extensions for Traffic Engineering (TE)",
               RFC 3784, June 2004.

   [RFC4090]   Pan, P., Ed., Swallow, G., Ed., and A. Atlas, Ed., "Fast
               Reroute Extensions to RSVP-TE for LSP Tunnels", RFC 4090,
               May 2005.

   [RFC4105]   Le Roux, J.-L., Ed., Vasseur, J.-P., Ed., and J. Boyle,
               Ed., "Requirements for Inter-Area MPLS Traffic
               Engineering", RFC 4105, June 2005.

   [RFC4203]   Kompella, K., Ed., and Y. Rekhter, Ed., "OSPF Extensions
               in Support of Generalized Multi-Protocol Label Switching
               (GMPLS)", RFC 4203, October 2005.

   [RFC4205]   Kompella, K., Ed., and Y. Rekhter, Ed., "Intermediate
               System to Intermediate System (IS-IS) Extensions in
               Support of Generalized Multi-Protocol Label Switching
               (GMPLS)", RFC 4205, October 2005.

   [RFC4216]   Zhang, R., Ed., and J.-P. Vasseur, Ed., "MPLS Inter-
               Autonomous System (AS) Traffic Engineering (TE)
               Requirements", RFC 4216, November 2005.

   [RFC4655]   Farrel, A., Vasseur, J.-P., and J. Ash, "A Path
               Computation Element (PCE)-Based Architecture", RFC 4655,
               August 2006.

   [RFC4726]   Farrel, A., Vasseur, J.-P., and A. Ayyangar, "A Framework
               for Inter-Domain Multiprotocol Label Switching Traffic
               Engineering", RFC 4726, November 2006.

Vasseur, et al.             Standards Track                    [Page 19]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

   [RFC4736]   Vasseur, JP., Ed., Ikejiri, Y., and R. Zhang,
               "Reoptimization of Multiprotocol Label Switching (MPLS)
               Traffic Engineering (TE) Loosely Routed Label Switched
               Path (LSP)", RFC 4736, November 2006.

Authors' Addresses

   JP Vasseur (editor)
   Cisco Systems, Inc.
   1414 Massachusetts Avenue
   Boxborough, MA  01719
   USA

   EMail: jpv@cisco.com

   Arthi Ayyangar (editor)
   Juniper Networks
   1194 N. Mathilda Ave
   Sunnyvale, CA  94089
   USA

   EMail: arthi@juniper.net

   Raymond Zhang
   BT
   2160 E. Grand Ave.
   El Segundo, CA  90025
   USA

   EMail: raymond.zhang@bt.com

Vasseur, et al.             Standards Track                    [Page 20]
RFC 5152          Path Comp. for Inter-Domain TE LSPs      February 2008

Full Copyright Statement

   Copyright (C) The IETF Trust (2008).

   This document is subject to the rights, licenses and restrictions
   contained in BCP 78, and except as set forth therein, the authors
   retain all their rights.

   This document and the information contained herein are provided on an
   "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
   OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
   THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
   OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
   THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
   WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

   The IETF takes no position regarding the validity or scope of any
   Intellectual Property Rights or other rights that might be claimed to
   pertain to the implementation or use of the technology described in
   this document or the extent to which any license under such rights
   might or might not be available; nor does it represent that it has
   made any independent effort to identify any such rights.  Information
   on the procedures with respect to rights in RFC documents can be
   found in BCP 78 and BCP 79.

   Copies of IPR disclosures made to the IETF Secretariat and any
   assurances of licenses to be made available, or the result of an
   attempt made to obtain a general license or permission for the use of
   such proprietary rights by implementers or users of this
   specification can be obtained from the IETF on-line IPR repository at
   http://www.ietf.org/ipr.

   The IETF invites any interested party to bring to its attention any
   copyrights, patents or patent applications, or other proprietary
   rights that may cover technology that may be required to implement
   this standard.  Please address the information to the IETF at
   ietf-ipr@ietf.org.

Vasseur, et al.             Standards Track                    [Page 21]